Professional Documents
Culture Documents
Pdms Commads & Syntaxes:: Piping Design
Pdms Commads & Syntaxes:: Piping Design
PIPING DESIGN:
14. Q_HCON: To verify Head connection type. E.g. bwd, open, close, etc.
15. Q_TCON: To verify Tail connection type. E.g. bwd, open, close, etc.
16. Q_HDIR: To verify the direction of the head.
17. Q_TDIR: To verify the direction of the tail.
18. Q_HPOS: To verify the position of the head.
19. Q_TPOS: To verify the position of the tail.
20. Q_HBOR: To verify the nominal bore (NB) of the head in mm.
21. Q_TBOR: To verify the nominal bore (NB) of the tail in mm.
22. Q_PSPEC: To verify the pipe specification, branch default spec.
23. Q_ISPEC: To verify the pipe insulation specification.
24. Q_TEMP: To check & change the temperature of the branch.
25. Q_INSUL: To check & change the insulation thickness of pipe, branch.
26. Q_HSTU: To check the attributes of head side tube of branch.
27. MOVE_PH (PT) _BY_ (DIR) _ (DIST) _WRT_/*: To move the head position or tail
position in a direction opposite to the head or tail.
GENERAL COMMANDS:
1. F1: HELP
2. F2: ZOOM
3. F3: PAN
4. F4: PERSPECTIVE
5. F5: ROTATE
6. F6: WALK
7. F7: EYE
8. F8: SHADE/WIREFRAME
9. F9: BORDER
10. Q_ATT: To verify the attributes of any item like pcom, sctn, equip, zon & sit, etc.
11. Q_AT: To check the position of any comp, hierarchy of any level, but not applicable
for some of items like FRMW, SBFR, ETC.
12. Q_POS_ID, IDP, IDPL_@: To check the pos of comp at a particular point or pline or
by its origin.
13. BRA_CONN_PH_TO_FIR_MEM: When in forwards mode & head is
opened to atmosphere.
14. BRA_CONN_PT_TO_LAS_MEM: When in forwards mode & tail is
opened to atmosphere.
15. BRA_CONN_PH_TO_ID, IDP_@: To conn branch head to any other
item like tee, flange, elbow, etc.
16. BRA_CONN_PT_TO_ID, IDP_@: To conn branch tail to any other
item like tee, flange, elbow, etc.
17. BRA_CONN_PH_TO_PT_OF_ID@: To conn branch head to tail of other
adjacent branch it may same pipe or different pipe.
18. BRA_CONN_PH_TO_PT_OF_ID@: To conn branch tail to head of other
adjacent branch it may same pipe or different pipe.
19. Q_NAM: To name any item like any sit, zon, stru, equip, inst, pipe, etc.
20. Q_CUTLEN: To know the total cut length of the section.
21. Q_DERLEN: To know the total derived length of the section(same as
Cutlen command).
22. SAVEWORK: To save the process we done before.
23. Q_IDP@: To check the attributes of a particular point of a component for
example tee has three points’ p1, p2 & p3.
24. VAR_1_NAM: It’s like the copy or move command. To copy item NEW_ (ITEM)
_COPY_$V1, to move item INCL_$V1 in this case before moving the item we must
keep item current element as we need include into that hierarchy.
25. CONN_NEX: It connects ce with previous item & makes next item as ce.
26. NEX_CONN: Connect the next item with the current element.
27. NEX_THR_CE: Aligns the next component with current element.
28. THR_NEX: Align the current element with the next component.
29. PRE_THR_CE: Aligns the previous component with current element.
30. THR_PRE: Align the current element with the previous component.
31. THR_ID,IDP,&IDPL @: Aligns the CE with the identified component, point or pline.
32. Q_MAP: To see & to know about different databases.
33. Q_LAS: To know the name of last member of that particular hierarchy.
34. LAS: It switches to the last member (item) of the hierarchy.
35. Q_FIR: To know the name of first member of that particular hierarchy.
36. FIR: It switches to the first member (item) of the hierarchy.
37. 1SEL: It selects the first item of the branch, pipe, zone, site, world.
38. FIR5: It selects the first fifth of the same hierarchy.
39. LAS5: It select from the last fifth of the same hierarchy.
40. Q_OWN: It gives the owner name.
41. OWN: It goes to its higher level that is to its owner.
42. PRE: It goes to the previous item at any level.
42. NEX: It goes to the next item at any level.
43. FOR: It makes the creation mode forwards.
44. BAC: It makes the creation mode backwards.
45. PLAN_THR_PT: To move an item through tail position at a derived direction.
46. PLAN_THR_NEX: To move an item through position of next component to the
direction of next component from CE.
47. MOV_ (DIR) _THR_ID@ or MOV_THR_ID@: Move the item through item pick
with respect to picked item direction.
48. NEW_ (ITEM) _COPY_PRE_REN_(PRE ITEM NAME)_(NEW
NAME)_BY_(DIR)_WRT_/*: This is used to copy a pipe with same name with small
change in name, but not only for the pipe also for other items which have more
subdivisions like STRU have many FRMWs, many SUBSs, SBFRs, etc.
49. NEW_ (ITEM) _COPY_PRE_MOV_THR_PT, PH, ID, IDP, IDPL@: This is used to
copy the previous item at the same time to move the copied item with respect to the
identified point of direction or through the tail position or head position .
50. NEW_(ITEM)_CHOO_ALL_MOV_THR_ID@: This is used to create new item by
choosing all items from table at the same time move the item with respect to the
identified point of direction.
51. CHOO_ALL_MOV_THR_ID@: This is used to reselect the item at the same time
move the item to a particular direction of pick.
52. Q_MDB: To verify the MDB.
53. MDB_NOUPD: