Professional Documents
Culture Documents
11
11
class EUtranCellFDD
class EUtranCellFDD
ManagedElement
+-ENodeBFunction
+-EUtranCellFDD
+-Cdma20001xRttBandRelation [0..32]
+-Cdma2000FreqBandRelation [0..32]
+-EUtranFreqRelation [0..8]
+-GeranFreqGroupRelation [0..16]
+-UeMeasControl [1..1]
+-UtranFreqRelation [0..16]
This MO represents a Cell and contains parameters needed by the cell. It also contains
parameters for the mandatory common channels.
Filter: FDD
Possible parents:
ENodeBFunction;
Possible children:
Cdma20001xRttBandRelation [0..32]; Cdma2000FreqBandRelation [0..32];
EUtranFreqRelation [0..8]; GeranFreqGroupRelation [0..16]; UeMeasControl [1..1];
UtranFreqRelation [0..16];
References to:
AirIfLoadProfile; ExternalCdma20001xRttCell; ManagedObject; QciTable; SectorCarrier;
SectorEquipmentFunction;
Actions
void changeFrequency ( long earfcn );
throws ChangeFrequencyException
Changes the frequency of the cell. The attribute earfcndl is changed. This MO action
includes the following steps:
- For neigbouring cells with existing cell relations to the cell, create new
EUtranFreqRelation instances (if not already existing) and new EUtranCellRelation
instances (with the same attribute values as the existing EUtranFreqRelation and
EUtranCellRelation MOs).
- For the changed cell an instance of EUtranFreqRelation with reference to the correct
instance of EUtranFrequency is created, if not already existing (with the same
attribute values as the existing EUtranFreqRelation MO).
Note that changing frequency of a EUtranCellFDD will imply that all other eNBs that
have this cell configured as an ExternaEUtranCellFDD will be updated with the new
frequency. This means that new EUtranFreqRelation and corresponding
EUtranFrequency MOs might be created.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 2 of 162
Parameters
Name: earfcn
Range: 0..17999
Description: The new DL frequency for this cell.
void startAilg ( );
throws AlreadyStartedException
throws DeviceDisabledException
throws InternalErrorException
throws MoAccessException
throws NoLicenseException
Starts the execution of the optional feature Air Interface Load Generation.
Attributes
AcBarringConfig acBarringForCsfb
Access class barring parameters for mobile originating CSFB
calls.
The information is broadcasted in SIB2.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 3 of 162
The list may include up to 5 PLMNs, and they must be the same
in all EUtranCells in the node.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 4 of 162
make ACS detect a sleeping cell slower, but with lower risk for
false detection.
Dependencies: None
Takes effect: Immediately
boolean ailgActive
nonPersistent
readOnly The state of the feature Air Interface Load Generator. Indicates
if it is running or stopped.
AirIfLoadProfile ailgRef
Refers to an instance of AirIfLoadProfile. Assigns a
AirIfLoadProfile to a cell.
Unit: 1 meter
Takes effect: Immediately
AltDirVals altitudeDir = HEIGHT
The antenna altitude direction. Valid values are HEIGHT and
DEPTH.
Dependencies: None
Takes effect: Immediately
AvailabilityStatus availabilityStatus
nonPersistent
readOnly The availability status. It contains details about
operationalState. This attribute is set by the application in the
RBS.
Cdma2000SysTimeVals bcCdma2000SysTimeType
nonPersistent
readOnly The actual type of CDMA2000 system time that is broadcast in
SIB8.
PlmnIdentity[0..2] bPlmnList
nonUnique
The Public Land Mobile Network (PLMN) ID of the cell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 5 of 162
Range 0-255.
long cellRange = 15 { 1..100 }
Defines the maximum distance from the base station where a
connection to a UE can be setup and/or maintained.
Unit: 1 km
Disturbances: Changes may affect traffic.
Takes effect: Object unlocked
CellReservedForOperatorUse cellReservedForOperatorUse = NOT_RESERVED
[0..2] nonUnique
Indicates if the cell is reserved for operator use.
The first index is for the primary Public Land Mobile Network
(PLMN) of the cell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 6 of 162
Unit: 1 ms
Dependencies: For 1.4 MHz: Only valid inputs are 10 and 20.
Takes effect: Cell lock/unlock
long confidence = 100 { 0..100 }
Percentage of confidence that the target device is within the
ellipsoid defined by the three axes of uncertainty: semi-major,
semi-minor, and altitude.
Unit: 1 percent
Dependencies: None
Takes effect: Immediately
long configurableFrequencyStart = 0 { 0..100 }
The start frequency offset for allocating resources when the
downlink interference management is disabled. Expressed as a
percentage of the available bandwidth.
Unit: 1 Percentage
Deprecated: Replaced by dlConfigurableFrequencyStart. Since
L11B.
Unit: 1 kHz
Dependencies: This attribute is dependent on and shall be set to
the same as ulChannelBandwidth.
Disturbances: Changes may affect traffic.
Takes effect: Object disabled/enabled.
long dlConfigurableFrequencyStart = 0 { 0..100 }
Specifies the start frequency offset for the allocation of
resources when the downlink interference management is
disabled expressed as a percentage of the configured
bandwidth.
Unit: 1 percent
Dependencies: dlInterferenceManagementActive shall be
disabled before this parameter takes effect.
Takes effect: Object unlocked
long dlFrequencyAllocationProportion = 100 { 0..100 }
Specifies the amount of frequency resources that is allocated in
DL expressed as a percentage of the configured bandwidth.
Unit: 1 percent
Takes effect: Object unlocked
boolean dlInterferenceManagementActive = false
Specifies if the downlink interference management is enabled or
disabled.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 7 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 8 of 162
noNotification
restricted
EutranCellCorner[0..15] eutranCellPolygon
nonUnique
Models the manageable characteristics for the cell polygon used
for UE positioning. Each polygon corner is described by a
latitude and longitude pair. Each polygon corner is represented
with one position in the sequence. The other configured polygon
corners follow in sequence. There must at least be three corners
configured in a polygon when the function is active/used. The
points shall be connected in the order that they are given. The
last point is connected to the first point.
Unit: 1 Seconds
Dependencies: None
boolean highSpeedUEActive = false
Indicates if the feature High Speed UE is activated in the cell
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 9 of 162
Dependencies: None
Takes effect: Immediately
long lbUtranOffloadThreshold = 100 { 0..1600 }
Threshold for eNodeB
The value applies for offload towards UTRAN target cells. The
eNodeB attempts to offload traffic from the source cell
corresponding to the subscription ratio above the threshold.
Unit: 0.01 .
Takes effect: Immediately
long longitude = 0 { -180000000..180000000 }
The degree of longitude of the transmitter antenna position.
In case of Combined Cell (multi-sector cell):
For indoor system, antenna of any sector.
For outdoor system,antenna of macro sector.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 10 of 162
Dependencies: None
Takes effect: Object unlocked
long noOfDefPagCyclPrim = 8 { 1..16 }
Number of consecutive "DefaultPagingCycles" in which paging
for Earthquake and Tsunami Warning System (ETWS) Primary
Notification shall be transmitted in the cell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 11 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 12 of 162
N <= X < (N + 1)
Unit: 1 degrees
Dependencies: None
Takes effect: Immediately
boolean otdoaSuplActive = false
Indicates if the feature OTDOA Support in SUPL Environment is
ACTIVATED or DEACTIVATED in the cell.
Unit: 1 %
Deprecated: Replaced by partOfSectorPower. Since L11B.
Unit: 1 %
Deprecated: Since L13A. Planned to be removed. Replaced by
SectorCarrier::partOfSectorPower. The value from the first
SectorCarrier in the
EUtranCellFDD/EUtranCellTDD::sectorCarrierRef will be mapped
to this deprecated attribute.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 13 of 162
Unit: 0.001 .
Takes effect: Cell lock/unlock
CfiMode pdcchCfiMode = CFI_STATIC_BY_BW
Controls the CFI (Control Format Indicator) used for the control
region. cfiMode maps to CFI as described under enumerations.
For DL BW of 1400 kHz, values of CFI = 1, 2 and 3 map to 2, 3,
and 4 control region symbols respectively. Other BW, CFI maps
directly to number of control region symbols.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 14 of 162
Dependencies: None
Takes effect: Object unlocked
long prsConfigIndex = -1 { -1..4095 }
The Positioning Reference Signal (PRS) index value for the cell
defines the periodicity of the PRS occasions and the PRS
subframe offset, as defined in 3GPP TS 36.211. The value -1
(default) means that this parameter will not be used for setting
the PRS period and prsSubframeOffset. Instead the parameter
prsPeriod shall be used to directly set the PRS period while
prsSubframeOffset will be set by the system to guarantee non
collision with SIB1.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 15 of 162
Unit: 1 dBm
Disturbances: Changes may affect traffic.
Takes effect: Immediately
long pZeroNominalPusch = -103 { -126..24 }
The nominal component of the UE transmit power for Physical
Uplink Shared Channel (PUSCH).
Unit: 1 dBm
Disturbances: Changes may affect traffic.
Takes effect: Immediately
QciTable qciTableRef
Refers to an instance of QciTable and assigns a QciTable to a
cell. The QciTable defines Quality of Service Class Indicator
(QCI) to use in the cell.
Unit: 1 dB
Dependencies: The field is mandatory present if the Struct
Member threshServingLowQ in SIB3 is used in
systemInformationBlockType3.
Takes effect: Immediately
long qQualMinOffset = 0 { 0..8 }
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 16 of 162
Unit: 1 dB
Dependencies: If the value of qQualMin is set to 0 the
parameter qQualMinOffset will not be broadcasted.
Takes effect: Immediately
long qRxLevMin = -140 { -140..-44 }
The required minimum received Reference Symbol Received
Power (RSRP) level in the E-UTRA frequency for cell reselection.
Corresponds to parameter Qrxlevmin in 3GPP TS 36.304. This
attribute is broadcast in SIB1.
Unit: 1 dBm
Resolution: 2
Takes effect: Immediately
long qRxLevMinOffset = 1000 { 2..16, 1000 }
The offset applied to the signalled Qrxlevmin. Corresponds to
parameter Qrxlevminoffset in 3GPP TS 36.304. Value 1000
means it is not sent and the UE sets Qrxlevminoffset=0dB.
Unit: 1 dB
Resolution: 2
Takes effect: Immediately
long rachRootSequence = 386 { 0..837 }
The first root sequence number for Random Access Channel
(RACH) preamble generation. RACH root sequence is broadcast
as a part of system information distribution and used for
preamble detection.
See definition for logical root sequence number in 3GPP TS
36.211.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 17 of 162
ManagedObject redirectionInfoRefPrio2
Reference to an Managed Object instance containing redirection
information for this EUtranCell. This reference should be set to a
Cdma2000Freq, EUtranFrequency, UtranFrequency or
GeranFrequencyGroup instance. Redirect to the same frequency
is possible.
PeriodicitySI siPeriodicity
The periodicity of System Information (SI) messages. If a
System Information Block (SIB) is not mapped to a SI message,
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 18 of 162
Unit: 1 ms
Dependencies: siWindowLength * ‘transmitted number of SI-
messages’ <= MIN(siPeriodicitySIx), i.e it must be possible
schedule all SI messages within the shortest siPeriodicity time
used.
Takes effect: When EUtranCellFDD/TDD object is unlocked
AcBarringConfig ssacBarringForMMTELVideo
Service specific access class barring parameters for MMTEL
video originating calls.
The information in broadcasted in SIB2.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 19 of 162
Unit: 1 dB
Resolution: 2
Takes effect: Immediately
string timeOfLastModification = "" [ 0..19 ]
Indicates the time and date when the MO was last modified.
Format: YYYY-MM-DD HH:MM:SS
Unit: 1 kHz
Dependencies: This attribute is dependent on and shall be set to
the same as dlChannelBandwidth.
Disturbances: Changes may affect traffic.
Takes effect: Object disabled/enabled.
long ulConfigurableFrequencyStart = 0 { 0..100 }
Specifies the start frequency offset for the allocation of
resources when the uplink interference management is disabled
expressed as a percentage of the configured bandwidth.
Unit: 1 percent
Dependencies: ulInterferenceManagementActive shall be
disabled before this parameter takes effect.
Takes effect: Object unlocked
long ulFrequencyAllocationProportion = 100 { 0..100 }
Specifies the amount of frequency resources that is allocated in
UL expressed as a percentage of the configured bandwidth.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 20 of 162
Unit: 1 percent
Takes effect: Object unlocked
boolean ulInterferenceManagementActive = true
Specifies if uplink interference management is enabled or
disabled.
Unit: 45 * ((1.025)^k - 1) .
Takes effect: Immediately
long uncertSemiMajor = 0 { 0..127 }
Semi-major axis of uncertainty. The uncertainty (r) is derived
from the uncertainty code (k) by:
r = 10 * ((1.1^k) - 1).
r = 10 * ((1.1^k) - 1).
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 21 of 162
PM counters
long pmActiveDrbDlSum
noNotification
nonPersistent The sum of the contributions from each UE in the cell of the number of
readOnly active DRBs in the downlink direction.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 22 of 162
Condition: Each TTI, the counter shall be increased wih the number of DRBs
that are considered active (i.e. that have data in the downlink buffer).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmActiveDrbDlSumQci
nonUnique
noNotification The sum of number of DL active DRBs per QCI. A DL DRB is active if there
nonPersistent are buffered DL data for the DRB. (Due to implementation, there are either
readOnly 9052 or 9053 samples per ROP)
Compressed: True
Condition: The bin accumulates the number of active DRBs in DL per QCI.
Counter type: PDF
Sampling rate: 0.1
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmActiveDrbUlSum
noNotification
nonPersistent The sum of the contributions from each UE in the cell of the number of
readOnly active DRBs in the uplink direction.
Condition: Each TTI, the counter shall be increased wih the number of DRBs
that are considered active (i.e. that are considered to have data in the
uplink buffer).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmActiveUeDlMax
noNotification
nonPersistent Peak number of UEs considered active in the downlink direction, i.e. has
readOnly designated data in UE dedicated buffer in the eNB. The value is a maximum
of a set of samples, where each sample is an average of active UEs per ms
(throughout the frame), during a sample period shorter than the ROP.
Condition: The counter is set equal to the peak sample recognized at the
end of each Recording Output Period (ROP).
Counter type: GAUGE
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..6] pmActiveUeDlSectorCarrierDistr
nonUnique
noNotification The counter shows the distribution of DL UEs that are in 1 to N sectors.
nonPersistent
readOnly [0]: Sum of active DL UEs that is connected to 1 sector
[1]: Sum of active DL UEs that is connected to 2 sectors
-----
[5]: Sum of active DL UEs that is connected to 6 sectors or more.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 23 of 162
Condition: The counter aggregates for each TTI the number of UEs with
DRB data to send.
Counter type: ACC
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmActiveUeDlSumQci
nonUnique
noNotification The sum of number of DL active UE per QCI. A DL active UE for a QCI is a
nonPersistent UE that has buffered DL data for the QCI. (Due to implementation, there
readOnly are either 9052 or 9053 samples per ROP)
Compressed: True
Condition: The counter is set to peak sample recognized at the end of each
Recording Output Period (ROP).
Counter type: GAUGE
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..6] pmActiveUeUlSectorCarrierDistr
nonUnique
noNotification The counter shows the distribution of UL UEs that are in 1 to N sectors.
nonPersistent
readOnly [0]: Sum of active UL UEs that is connected to 1 sector
[1]: Sum of active UL UEs that is connected to 2 sectors
-----
[5]: Sum of active UL UEs that is connected to 6 sectors or more.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 24 of 162
Condition: The counter aggregates for each TTI the number of UEs with
buffer status reports indicating DRB data to be sent in the uplink direction.
Counter type: ACC
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..4] pmActiveUeUlSumLcg
nonUnique
noNotification The sum of number of UL active UE per LCG (Logical Channel Group). An UL
nonPersistent active UE for a LCG is a UE that has buffered UL data for the LCG. (Due to
readOnly implementation, there are either 9052 or 9053 samples per ROP)
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 25 of 162
triggered).
Filter: FDD
Condition: Stepped in each subframe (TTI) for UEs using this cell as a
primary component carrier (PCell) and which are configured with at least
one secondary component carrier (SCell).
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 26 of 162
Filter: FDD
Condition: This measurement provides the mean number of UEs capable of
downlink carrier aggregation, counted per the number of component
carriers (PCell and SCells).
Filter: FDD
Condition: This measurement provides the mean number of UEs configured
for downlink carrier aggregation, out of the number of carrier aggregation
capable UEs, counted per the number of component carriers (PCell and
SCells) configured in each UE.
Counter type: PDF
Sampling rate: 5
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..5] pmCaScheduledDlSum
nonUnique
noNotification Mean number of UE that have data scheduled on downlink, counted by the
nonPersistent number of component carriers simultaneously scheduled.
readOnly UE is considered scheduled for carrier aggregation if the eNodeB has sent a
PDCCH assignment indicating a PDSCH assignment
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 27 of 162
Filter: FDD
Condition: Stepped in each subframe (TTI) for UEs using this cell as a
primary component carrier (PCell) and which are activated with at least one
secondary component carrier (SCell).
Unit: 1 Rejects
Condition: The counter is stepped in dl scheduler when a ue is going to be
setup, if the pdcchAdmEnabled attribute is set to true, and the usage of
CCEs for high prioritized Ues is above the threshold pdcchAdmThreshold. A
reject is also sent to higher layers.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmCellAdmControlPdcchRejMeas
noNotification
nonPersistent Counter is stepped whenever we would have had a reject due to that pdcch
readOnly is limiting new connections.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 28 of 162
Unit: 1 s
Condition: Incremented by one each second.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long pmCellDowntimeMan
noNotification
nonPersistent Length of time the cell has been disabled due to:
readOnly - AdministrativeState of the cell MO or another MO the cell depends on has
been set to Locked by the operator
or
- the operator has performed a reconfiguration request on an Unlocked cell
which requires the cell to be taken down temporarily.
The counter is only incremented when the RBS is operational.
Unit: 1 s
Condition: Incremented by one each second.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long pmCellDownUnlockMan
noNotification
nonPersistent The number of times the cell has been enabled.
readOnly
Condition: Incremented at change of the AdministritiveState to Unlocked.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..8] pmCompUlDeltaSinrPuschDistr
nonUnique
noNotification Distribution of the SINR difference for PUSCH between Uplink Coordinated
nonPersistent Multi-Point Reception and Interference Rejection Combining within
readOnly SectorCarrier.
PDF ranges:
[0]: DeltaSINR <= -1;
[1]: -1<DeltaSINR <= 0;
[2]: 0 < DeltaSINR 2 <= 2;
[3]: 2 < DeltaSINR <= 4;
[4]: 2 < DeltaSINR <= 4;
[5]: 4 < DeltaSINR <= 6;
[6]: 6 < DeltaSINR <= 8;
[7]: 8 < DeltaSINR <= 10;
Unit: 1 dB
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 29 of 162
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of DL capacity license, hardware capacity or
PDCCH resources is counted. Note that result is dependent on the
configuration of Subframe assignment (i.e. How many TTIs are available to
scheduling).
Counter type: PEG
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmContDlCapLic
noNotification
nonPersistent The counter aggregates the number of ms for which contention has
readOnly occurred in the downlink direction due to lack of DL capacity license.
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of DL capacity license is counted. Note that
result is dependent on the configuration of Subframe assignment (i.e. How
many TTIs are available to scheduling).
Counter type: PEG
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmContDlHw
noNotification
nonPersistent The counter aggregates the number of ms for which contention has
readOnly occurred in the downlink direction due to lack of hardware resources.
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of hardware resources is counted. Note that
result is dependent on the configuration of Subframe assignment (i.e. How
many TTIs are available to scheduling).
Counter type: PEG
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmContDlPdcch
noNotification
nonPersistent The counter aggregates the number of ms for which contention has
readOnly occurred in the downlink direction due to lack of PDCCH resources.
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of PDCCH resources is counted. Note that result
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 30 of 162
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of UL capacity license, hardware capacity or
PDCCH resources is counted. Note that result is dependent on the
configuration of Subframe assignment (i.e. How many TTIs are available to
scheduling).
Counter type: PEG
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmContUlCapLic
noNotification
nonPersistent The counter aggregates the number of ms for which contention has
readOnly occurred in the uplink direction due to lack of license resources.
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of UL capacity license is counted. Note that
result is dependent on the configuration of Subframe assignment (i.e. How
many TTIs are available to scheduling).
Counter type: PEG
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmContUlHw
noNotification
nonPersistent The counter aggregates the number of ms for which contention has
readOnly occurred in the uplink direction due to lack of hardware resources.
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of hardware resources is counted. Note that
result is dependent on the configuration of Subframe assignment (i.e. How
many TTIs are available to scheduling).
Counter type: PEG
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmContUlPdcch
noNotification
nonPersistent The counter aggregates the number of ms for which contention has
readOnly occurred in the uplink direction due to lack of PDCCH resources.
Unit: 1 ms
Condition: Any TTI for which contention (i.e. data not scheduled for a Radio
Bearer) occurs due to lack of PDCCH resources is counted. Note that result
is dependent on the configuration of Subframe assignment (i.e. How many
TTIs are available to scheduling).
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 31 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 32 of 162
Compressed: True
Unit: 1 ms
Filter: FDD
Condition: The bin accumulates the DL transmission time per QCI for each
large data burst that needs to be transmitted across multiple TTIs.
Counter type: PDF
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmDrxSleepTime
noNotification
nonPersistent Contains the DRX sleep time in number of subframes for all UEs in the cell.
readOnly
Compressed: True
Unit: 1 ms
Compressed: True
Unit: 1 ms
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 33 of 162
Compressed: True
Unit: 1 ms
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 34 of 162
removed.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 35 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 36 of 162
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabAdmissionAttArp4
noNotification
nonPersistent The total number of E-RAB admission attempts for ARP (Allocation
readOnly Retention Priority)=4
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 37 of 162
long pmErabAdmissionAttArp8
noNotification
nonPersistent The total number of E-RAB admission attempts for ARP (Allocation
readOnly Retention Priority)=8
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 38 of 162
nonPersistent The total number of admitted E-RAB Establishment for ARP (Allocation
readOnly
Retention Priority)=10
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 39 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 40 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 41 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 42 of 162
Condition: Shall be stepped for each E-RAB Establishment attempt per QCI
at reception of S1-AP message E-RAB Setup Request.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabEstabAttGbr
noNotification
nonPersistent The total number of E-RAB setup attempts with resource type GBR for a
readOnly cell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 43 of 162
nonPersistent The total number of initial E-RAB setup attempts per QCI.
readOnly
Compressed: True
Condition: Shall be stepped for each E-RAB Establishment attempt per QCI
at reception of S1-AP message Initial Context Setup Request.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabEstabFailAddedLic
noNotification
nonPersistent The total number of failed establishment of added E-RABs due to license
readOnly rejects (Multiple Radio Bearer per user or RLC UM). Added E-RABs are all
E-RABs present in S1 message E-RAB Setup Request.
Condition: Stepped for each added E-RAB that fails to be established due to
a license reject (Multiple Radio Bearer per user or RLC UM). The specific
license will be indicated in the PM event triggered by this counter.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 44 of 162
long pmErabEstabFailGbrUlEnb
noNotification
nonPersistent The total number of failed E-RAB setup attempts due to uplink GBR
readOnly overload for resources common to the eNodeB.
Condition: Stepped for each initial E-RAB that fails to be established due to
a license reject (Multiple Radio Bearer per user or RLC UM).The specific
license will be indicated in the PM event triggered by this counter.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long pmErabEstabSuccAdded
noNotification
nonPersistent The total number of successfully added E-RABs. Added E-RABs are all
readOnly E-RABs present in S1 message E-RAB Setup Request.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 45 of 162
noNotification The total number of successful additional E-RAB setup per QCI.
nonPersistent
readOnly
Compressed: True
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 46 of 162
noNotification The total number of successful initial E-RAB setup per QCI.
nonPersistent
readOnly
Compressed: True
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 47 of 162
nonPersistent to QCI y, bin [x] would be used (and for subsequent E-RAB Modify
readOnly
attempts, bin [y] would be used).
Compressed: True
Condition: Shall be stepped for each E-RAB modification attempt per QCI at
reception of S1-AP message E-RAB Modify Request.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabModFailLic
noNotification
nonPersistent The number of E-RAB Modify attempts initiated from the MME which failed
readOnly due to license reject.
Condition: Stepped for each E-RAB for which modification failed due to
license reject.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmErabModSuccQci
nonUnique
noNotification The number of successful E-RAB Modify attempts per QCI.
nonPersistent Note: since the QCI itself can be modified, if an E-RAB on QCI x is modified
readOnly to QCI y, bin [x] would be used (and for subsequent E-RAB Modify
attempts, bin [y] would be used).
Compressed: True
Condition: The bin represents the max number of simultaneous E-RABs per
QCI among all measured values within the measurement period.
Counter type: PDF
Sampling rate: 5
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 48 of 162
long pmErabRelAbnormalEnb
noNotification
nonPersistent The total number of abnormal E-RAB Releases triggered by eNB per cell.
readOnly
Condition: Stepped at reception of S1 message E-RAB Release Command or
UE Context Release Command where the cause value indicates system
(abnormal) release with the pre-condition that the Initial Context
Establishment procedure must first have been successfully completed. The
release must also have been eNB initiated.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelAbnormalEnbAct
noNotification
nonPersistent The total number of abnormal E-RAB Releases per cell initiated by the eNB
readOnly and that there was data in either the UL or DL buffer (i.e. active).
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message E-RAB Release Command or UE
Context Release Command when internal cause codes considered abnormal
(Radio Connection with UE is lost; Handover failure for the UE; Non
admitted E-RABs by target cell at successful handover for the UE; UE pre-
emption) when the RBS initiated the release. It can also be stepped at
transmission of E-RAB Release Indication, UE Context Release Request or
Reset message by the RBS, or when a cell owned by that RBS is disabled
(and that leads to internal RBS UE Context Release). In the UL case when a
UE has multiple bearers co-existing and sharing the same LCG, the bearers
share a single packet queue. If one of the bearers is released and there is
data in the queue, the bearer's associated counter is incremented,
regardless of whether or not the data belongs to the released bearer.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..16] pmErabRelAbnormalEnbActArp
nonUnique
noNotification The total number of abnormal E-RAB Releases initiated by the RBS (per cell
nonPersistent per ARP). The counter is stepped if data was present in the UL or DL
readOnly buffers.
Type:
Compressed PDF
[0]: Sum of active E-RABs released with ARP priority value 0
[1]: Sum of active E-RABs released with ARP priority value 1
….
[15]: Sum of active E-RABs released with ARP priority value 15
Compressed: True
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message E-RAB Release Command or UE
Context Release Command, for E-RAB/s with the specific ARP Priority Level,
when internal cause codes considered abnormal (Radio Connection with UE
is lost; Handover failure for the UE; Non admitted E-RABs by target cell at
successful handover for the UE; UE pre-emption; Bearer pre-emption)
when the RBS initiated the release. It can also be stepped at transmission
of Reset message by the RBS, or when a cell owned by that RBS is disabled
(and that leads to internal RBS UE Context Release). In the UL case when a
UE has multiple bearers co-existing and sharing the same LCG, the bearers
share a single packet queue. If one of the bearers is released and there is
data in the queue, the bearer's associated counter is incremented,
regardless of whether or not the data belongs to the released bearer.
Counter type: PDF
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 49 of 162
Condition: Stepped for each ERAB that is lost due to cell down time
(manual intervention) when data was in either the UL or DL buffer. In the
UL case when a UE has multiple bearers co-existing and sharing the same
LCG, the bearers share a single packet queue. If one of the bearers is
released and there is data in the queue, the bearer's associated counter is
incremented, regardless of whether or not the data belongs to the released
bearer.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelAbnormalEnbActHo
noNotification
nonPersistent The total number of abnormal ERAB releases per cell by the eNB due to
readOnly handover execution failure and that there was data in either the UL or DL
buffer (i.e. active).
Condition: If there was data in the buffer at the time of release, and the
release is due to that executed handover fails and the UE is considered
dropped. In the UL case when a UE has multiple bearers co-existing and
sharing the same LCG, the bearers share a single packet queue. If one of
the bearers is released and there is data in the queue, the bearer's
associated counter is incremented, regardless of whether or not the data
belongs to the released bearer.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelAbnormalEnbActHpr
noNotification
nonPersistent The total number of abnormal ERAB releases by the eNB per cell due to
readOnly handover preparation and that there was data in either the UL or DL buffer
(i.e. active).
Condition: Stepped for each ERAB that is released due to pre-emption when
data was in either the UL or DL buffer. In the UL case when a UE has
multiple bearers co-existing and sharing the same LCG, the bearers share a
single packet queue. If one of the bearers is released and there is data in
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 50 of 162
Compressed: True
Condition: The bin is steped for each released active E-RAB that maps to a
certain QCI when the release is triggered by an E-RAB Release Indication,
UE Context Release Request or Reset message and has a internal abnormal
cause code, except active E-RABs released due to a successful HO. In the
UL case when a UE has multiple bearers co-existing and sharing the same
LCG, the bearers share a single packet queue. If one of the bearers is
released and there is data in the queue, the bearer's associated counter is
incremented, regardless of whether or not the data belongs to the released
bearer.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelAbnormalEnbActTnFail
noNotification
nonPersistent The total number of abnormal ERAB releases per cell due to S1 interface
readOnly down, "X2 interface down" or "Transport Resource Unavailable", with the
pre-condition that the Initial Context Establishment procedure must first
have been successfully completed and that there was data in either the UL
or DL buffer (i.e. active).
Condition: If there was data in the buffer at the time of release of an E-RAB
and due to that the S1 interface is lost or S1 bearer error indication is
received. In the UL case when a UE has multiple bearers co-existing and
sharing the same LCG, the bearers share a single packet queue. If one of
the bearers is released and there is data in the queue, the bearer's
associated counter is incremented, regardless of whether or not the data
belongs to the released bearer.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelAbnormalEnbActUeLost
noNotification
nonPersistent The total number of abnormal ERAB releases by the eNB per cell due that
readOnly the contact with the UE is lost with the pre-condition that the Initial Context
Establishment procedure must first have been successfully completed and
that there was data in either the UL or DL buffer (i.e. active).
Condition: If there was data in the buffer at the time of release and if there
was a release of an UE due to that the radio connection towards the UE is
lost (i.e. UE unreachable by the RBS). In the UL case when a UE has
multiple bearers co-existing and sharing the same LCG, the bearers share a
single packet queue. If one of the bearers is released and there is data in
the queue, the bearer's associated counter is incremented, regardless of
whether or not the data belongs to the released bearer.
Counter type: PEG
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 51 of 162
Compressed: True
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 52 of 162
Compressed: True
Condition: The bin is stepped for each released E-RAB that maps to a
certain QCI when the release is triggered by an UE CONTEXT RELEASE
REQUEST message and has an internal abnormal cause code and with the
pre-condition that the Initial Context Establishment procedure must first
have been successfully completed.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelAbnormalMmeAct
noNotification
nonPersistent The total number of E-RAB Releases initiated by the MME considered as
readOnly abnormal. The counter is stepped if if there was data in either the UL or DL
buffer (i.e. active).
Compressed: True
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 53 of 162
Compressed: True
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message E-RAB Release Command or UE
Context Release Command (except if the cause was successful handover).
The release must also have been MME initiated. In the UL case when a UE
has multiple bearers co-existing and sharing the same LCG, the bearers
share a single packet queue. If one of the bearers is released and there is
data in the queue, the bearer's associated counter is incremented,
regardless of whether or not the data belongs to the released bearer.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long pmErabRelMmeActEutra
noNotification
nonPersistent The total number of E-RAB Releases per cell, initiated by the MME with the
readOnly pre-condition that the Initial Context Establishment procedure must first
have been successfully completed and that there was data in either the UL
or DL buffer (i.e. active) and the cause was "Release due to Eutran
generated reason".
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 54 of 162
Compressed: True
Condition: The bin is stepped for each released active E-RAB that maps to a
certain QCI when the release is triggered by MME through an E-RAB
RELEASE COMMAND or UE CONTEXT RELEASE COMMAND message, except
active E-RABs released due to a successful HO. In the UL case when a UE
has multiple bearers co-existing and sharing the same LCG, the bearers
share a single packet queue. If one of the bearers is released and there is
data in the queue, the bearer's associated counter is incremented,
regardless of whether or not the data belongs to the released bearer.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelMmeActUnspecified
noNotification
nonPersistent The total number of E-RAB Releases per cell, initiated by the MME with the
readOnly pre-condition that the Initial Context Establishment procedure must first
have been successfully completed and that there was data in either the UL
or DL buffer (i.e. active) and the cause was "Unspecified".
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 55 of 162
multiple bearers co-existing and sharing the same LCG, the bearers share a
single packet queue. If one of the bearers is released and there is data in
the queue, the bearer's associated counter is incremented, regardless of
whether or not the data belongs to the released bearer.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..16] pmErabRelMmeArp
nonUnique
noNotification The total number of E-RAB Releases initiated by the MME excluding
nonPersistent successful handover per cell per ARP Level. The counter is stepped
readOnly regardless of whether data was or was not lost in UL/DL buffers.
Type:
Compressed PDF
[0]: Sum of E-RABs released with ARP priority value 0 (unallowed ARP
level)
[1]: Sum of E-RABs released with ARP priority value 1
….
[15]: Sum of E-RABs released with ARP priority value 15
Compressed: True
Compressed: True
Condition: The corresponding QCI bin is stepped for each released E-RAB at
reception of S1 message E-RAB Release Command or UE Context Release
Command (except if the cause was successful handover) and with the pre-
condition that the Initial Context Establishment procedure must first have
been successfully completed. The release must also have been MME
initiated.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmErabRelNormalEnb
noNotification
nonPersistent The total number of normal E-RAB Releases triggered by eNB per cell.
readOnly
Condition: Stepped at reception of S1 message E-RAB Release Command or
UE Context Release Command where the cause value indicates normal
release with the pre-condition that the Initial Context Establishment
procedure must first have been successfully completed. The release must
also have been eNB initiated.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 56 of 162
long pmErabRelNormalEnbAct
noNotification
nonPersistent The total number of normal E-RAB Releases per cell initiated by the eNB
readOnly and that there was data in either the UL or DL buffer (i.e. active).
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message E-RAB Release Command or UE
Context Release Command when internal cause codes considered normal
(User Inactivity, Inter-RAT redirection, CS Fallback Triggered) when the
RBS initiated the release. In the UL case when a UE has multiple bearers
co-existing and sharing the same LCG, the bearers share a single packet
queue. If one of the bearers is released and there is data in the queue, the
bearer's associated counter is incremented, regardless of whether or not
the data belongs to the released bearer.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..16] pmErabRelNormalEnbActArp
nonUnique
noNotification The total number of normal E-RAB Releases initiated by the RBS (per cell
nonPersistent per ARP). The counter is stepped if there was data lost in UL/DL buffers.
readOnly Type:
Compressed PDF
[0]: Sum of E-RABs released with ARP priority value 0
[1]: Sum of E-RABs released with ARP priority value 1
….
[15]: Sum of E-RABs released with ARP priority value 15
Compressed: True
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message E-RAB Release Command or UE
Context Release Command, for E-RAB/s with the specific ARP Priority Level,
when internal cause codes considered normal and the RBS initiated the
release. In the UL case when a UE has multiple bearers co-existing and
sharing the same LCG, the bearers share a single packet queue. If one of
the bearers is released and there is data in the queue, the bearer's
associated counter is incremented, regardless of whether or not the data
belongs to the released bearer.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmErabRelNormalEnbActQci
nonUnique
noNotification The total number of active E-RABs released normally (per cell per QCI) for
nonPersistent requests initiated by eNB, except active E-RABs released due to successful
readOnly HO. An E-RAB is considered to be active when there are data in the DL or
UL queues for the E-RAB.
Compressed: True
Condition: The bin is stepped for each released active E-RAB that maps to a
certain QCI when the release is triggered by an UE CONTEXT RELEASE
REQUEST message and has a normal release cause code, except active
E-RABs released due to a successful HO. In the UL case when a UE has
multiple bearers co-existing and sharing the same LCG, the bearers share a
single packet queue. If one of the bearers is released and there is data in
the queue, the bearer's associated counter is incremented, regardless of
whether or not the data belongs to the released bearer.
Counter type: PDF
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 57 of 162
Compressed: True
Condition: The bin is stepped for each released E-RAB that maps to a
certain QCI when the release is triggered by an UE CONTEXT RELEASE
REQUEST message and has an internal normal cause code and with the
pre-condition that the Initial Context Establishment procedure must first
have been successfully completed.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmHoExeAttQci
nonUnique
noNotification The number of handover execution attempt for ERABs per QCI towards
nonPersistent target cell.
readOnly
Compressed: True
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 58 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 59 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 60 of 162
Unit: 1 ms
Condition: The bin accumulates the UL transmission time per LCG for large
data bursts that need to be transmitted across multiple TTIs.
Counter type: PDF
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..4] pmLcgThpVolUlLcg
nonUnique
noNotification The UL volume used for UL DRB Throughput per LCG. It comprises of the
nonPersistent MAC SDU volume received on Uu per LCG, excluding the volume received in
readOnly the first 4 data transmissions and the data transmission emptying the UL
buffer.
Condition: The bin accumulates the UL volume per LCG for large data
bursts that needs to be transmitted across multiple TTIs.
Counter type: PDF
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmMacDelayTimeDl
noNotification
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 61 of 162
nonPersistent Aggregated time for the downlink MAC delay measure. The time for each
readOnly
sample shall show the time between reception from RLC until it is
successfully received in the UE or HARQ failure occurs.
Unit: 1 ms
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmMacHarqDlAck
noNotification
nonPersistent The total number of successful HARQ transmissions (ACKs) in the downlink
readOnly direction.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 62 of 162
nonPersistent The total number of occasions when an downlink HARQ feedback was not
readOnly
received from an UE and DTX is considered the reason.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 63 of 162
long pmMacHarqDlNack16qam
noNotification
nonPersistent The total number of unsuccessful HARQ transmissions in the downlink
readOnly direction using a 16QAM modulation.
Condition: To decide if it was failed is based on the HARQ NACK from the
UE.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmMacHarqDlNack64qam
noNotification
nonPersistent The total number of unsuccessful HARQ transmissions in the downlink
readOnly direction using a 64QAM modulation.
Condition: To decide if it was failed is based on the HARQ NACK from the
UE.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmMacHarqDlNackQpsk
noNotification
nonPersistent The total number of unsuccessful HARQ transmissions in the downlink
readOnly direction using a QPSK modulation.
Condition: To decide if it was failed is based on the HARQ NACK from the
UE.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmMacHarqUlAck
noNotification
nonPersistent The total number of successful HARQ transmissions (ACKs) in the uplink
readOnly direction.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 64 of 162
long pmMacHarqUlDtx16qam
noNotification
nonPersistent The total number of occasions when an uplink grant was meant for HARQ
readOnly transmission of a transport block using 16QAM modulation in the uplink
direction, where DTX is considered the reason for no receiption of HARQ in
uplink in the eNB.
Condition: To decide if it was failed is based on the CRC check for recieved
transport blocks (which results in NACK).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmMacHarqUlFailQpsk
noNotification
nonPersistent The total number of unsuccessful HARQ transmissions in the uplink
readOnly direction using a QPSK modulation.
Condition: To decide if it was failed is based on the CRC check for recieved
transport blocks (which results in NACK).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmMacHarqUlNack
noNotification
nonPersistent The total number of unsuccessful HARQ transmissions (NACKs) in the uplink
readOnly direction.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 65 of 162
Condition: When the cell fails to broadcast an RRC Paging within a certain
time (pagingDiscardTimer), e.g. due to congestion, the Paging is discarded
and this counter is incremented by the number of included Paging Records
in the discarded Paging message.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPagReceived
noNotification
nonPersistent This counter counts the number of S1AP Paging messages routed to this
readOnly cell.
Condition: When an S1AP Paging is routed to this cell which is correct and
complete. An S1AP Paging message discarded as part of pmPagS1Discarded
will not cause this counter to be pegged.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 66 of 162
Condition: The bin accumulates the number of CCEs used for UL grants
corresponding to TBs with bits belonging to a specific QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..20] pmPdcchCceUtil
nonUnique
noNotification PDF of % of CCEs utilized compared with total CCEs available (at the
nonPersistent maximum CFI permitted by pdcchCfiMode) each subframe, considering
readOnly bandwidth and antenna configuration.
[0]: utilization <= 5%
[1]: 5% < utilization <= 10%
[2]: 10% < utilization <= 15%
[3]: 15% < utilization <= 20%
[4]: 20% < utilization <= 25%
[5]: 25% < utilization <= 30%
[6]: 30% < utilization <= 35%
[7]: 35% < utilization <= 40%
[8]: 40% < utilization <= 45%
[9]: 45% < utilization <= 50%
[10]: 50% < utilization <= 55%
[11]: 55% < utilization <= 60%
[12]: 60% < utilization <= 65%
[13]: 65% < utilization <= 70%
[14]: 70% < utilization <= 75%
[15]: 75% < utilization <= 80%
[16]: 80% < utilization <= 85%
[17]: 85% < utilization <= 90%
[18]: 90% < utilization <= 95%
[19]: 95% < utilization <= 100%
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 67 of 162
Unit: 1 %
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 68 of 162
Condition: The PDF shall be updated each TTI with the percentage of
PDCCH resources used.
Counter type: PDF
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcchResyncAtt
noNotification
nonPersistent The total number of attempted 3GPP procedure "PDCCH ordered
readOnly resynchronization", see 3GPP TS 36.321 and TS 36.212.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) is measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 69 of 162
Unit: 1 kbps
Filter: FDD
Condition: The counter is set equal to the peak sample at the end of each
Recording Output Period (ROP).
Counter type: GAUGE
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpBitrateDlDrbMin
noNotification
nonPersistent Minimum cell DL bit rate. One cell bit rate sample is obtained by dividing
readOnly the total volume (PDCP SDU) on Data Radio Bearers aggregated to cell
level, that has been transmitted in the downlink direction in the PDCP layer,
with the time (in seconds) of the sample gathering period.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) is measured on PCell.
Unit: 1 kbps
Filter: FDD
Condition: The counter is set equal to the low mark sample at the end of
each Recording Output Period (ROP).
Counter type: GAUGE
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpBitrateUlDrbMax
noNotification
nonPersistent Peak cell UL bit rate. One cell bit rate sample is obtained by dividing the
readOnly total volume (PDCP SDU) on Data Radio Bearers aggregated to cell level,
that has been received in the uplink direction, with the time (in seconds) of
the sample gathering period.
Unit: 1 kbps
Condition: The counter is set equal to the peak sample at the end of each
Recording Output Period (ROP).
Counter type: GAUGE
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpBitrateUlDrbMin
noNotification
nonPersistent Minimum cell UL bit rate. One cell bit rate sample is obtained by dividing
readOnly the total volume (PDCP SDU) on Data Radio Bearers aggregated to cell
level, that has been received in the uplink direction, with the time (in
seconds) of the sample gathering period.
Unit: 1 kbps
Condition: The counter is set equal to the low mark sample at the end of
each Recording Output Period (ROP).
Counter type: GAUGE
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpDelayTimeDl
noNotification
nonPersistent Aggregated time for the downlink delay measure. One sample per
readOnly successful transmission of a packet (PDCP SDU). The time for each sample
is between reception of a packet (PDCP SDU) until the successful
transmission of the corresponding MAC SDU.
Unit: 1 ms
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 70 of 162
Filter: FDD
Condition: Measurement for UEs aggregated to cell level. Only PDCP SDUs
that enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
forwarding).
Counter type: PEG
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmPdcpLatPktTransDlDrxNoSync
noNotification
nonPersistent Number of DRB packets for downlink Latency measurements when DRX is
readOnly active and the UE has UL synchronization status "NOT synchronized".
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Filter: FDD
Condition: Measurement for UEs aggregated to cell level. Only PDCP SDUs
that enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
forwarding). The samples are included
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpLatPktTransDlDrxSync
noNotification
nonPersistent Number of DRB packets for downlink Latency measurements when DRX is
readOnly active and the UE has UL synchronization status "synchronized".
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Filter: FDD
Condition: Measurement for UEs aggregated to cell level. Only PDCP SDUs
that enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 71 of 162
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Filter: FDD
Condition: Measurement for UEs aggregated to cell level. Only PDCP SDUs
that enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
forwarding). The samples are included
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmPdcpLatPktTransDlQci
nonUnique
noNotification Number of samples for DL Latency measurements during measurement
nonPersistent period per QCI.
readOnly
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Compressed: True
Filter: FDD
Condition: The counter registers the number of samples for DL Latency
measurements during measurement period per QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpLatTimeDl
noNotification
nonPersistent Aggregated DL Latency for a measurement period. The effective DL Latency
readOnly time comprises the time from PDCP DRB SDU entering the buffer until the
first data has been transmitted to the UE.
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Unit: 1 ms
Filter: FDD
Condition: Measurement for UEs aggregated to cell level. Only PDCP SDUs
that enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 72 of 162
forwarding).
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmPdcpLatTimeDlDrxNoSync
noNotification
nonPersistent Aggregated DL Latency when DRX is active and the UE has UL
readOnly synchronization status "NOT synchronized".
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Filter: FDD
Condition: The effective DL Latency time comprises the time from PDCP
DRB SDU entering the buffer until the first data has been transmitted to the
UE. Measurement for UEs aggregated to cell level. Only PDCP SDUs that
enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
forwarding).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpLatTimeDlDrxSync
noNotification
nonPersistent Aggregated DL Latency when DRX is active and the UE has UL
readOnly synchronization status "synchronized".
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Filter: FDD
Condition: The effective DL Latency time comprises the time from PDCP
DRB SDU entering the buffer until the first data has been transmitted to the
UE. Measurement for UEs aggregated to cell level. Only PDCP SDUs that
enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
forwarding).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpLatTimeDlNoDrxSync
noNotification
nonPersistent Aggregated DL Latency when DRX is NOT active and the UE has UL
readOnly synchronization status "synchronized".
When carrier aggregation is used, the DL Latency for all component carriers
is registered on the UE's primary component carrier (PCell).
Filter: FDD
Condition: The effective DL Latency time comprises the time from PDCP
DRB SDU entering the buffer until the first data has been transmitted to the
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 73 of 162
UE. Measurement for UEs aggregated to cell level. Only PDCP SDUs that
enters an empty buffer are measured. Samples during handover are
excluded since they can distort the interpretation of the result (due to
packet forwarding, the target cell might have to buffer data before it is
possible to schedule the UE in the target cell, hence it would be an
increased Latency measurement if it would be included. It would however
not lead to a degraded performance for the end-user, due to packet
forwarding).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmPdcpLatTimeDlQci
nonUnique
noNotification Aggregated DL Latency for a measurement period per QCI.
nonPersistent When carrier aggregation is used, the DL Latency for all component carriers
readOnly is registered on the UE's primary component carrier (PCell).
Compressed: True
Unit: 1 ms
Filter: FDD
Condition: The counter represents DL latency per QCI. The effective DL
Latency time comprises the time from PDCP SDU entering the buffer until
the first data has been transmitted to the UE. Only latency for PDCP SDUs
that enters an empty buffer is measured. Samples during handover are
excluded.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpPktDiscDlAqm
noNotification
nonPersistent Total number of packets (PDCP SDUs) discarded due to Active Queue
readOnly Management (AQM).
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of packets (PDCP SDUs) discarded due
to AQM is measured on PCell.
Filter: FDD
Condition: When a packet is discarded due to AQM
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmPdcpPktDiscDlAqmQci
nonUnique
noNotification Total number of packets (PDCP SDUs) per QCI discarded due to Active
nonPersistent Queue Management (AQM).
readOnly
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of packets (PDCP SDUs) per QCI
discarded due to AQM is measured on PCell.
Compressed: True
Filter: FDD
Condition: When a packet is discarded due to AQM
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 74 of 162
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total number of packets (PDCP SDUs) discarded
in the downlink due to handover and reestablishment procedures is
measured on PCell.
Filter: FDD
Condition: The counter can be incremented from both source and target
point of view in the handover functionality. Discards in the target eNB could
be due to out of order sequence. Discards in the source eNB includes
discards of PDCP SDU packets not positively acknowledged for which it was
decided that no more transmission attempts on either Uu, X2 or S1
interface will be done. In the reestablishment functionality, packets in the
PDCP buffer are discarded due to the reestablishment procedure. Only
applicable to DRB packets.
Compressed: True
Filter: FDD
Condition: The counter can be incremented from both source and target
point of view in the handover functionality. Discards in the target eNB could
be due to out of order sequence. Discards in the source eNB includes
discards of packets not positively acknowledged PDCP SDU for which it was
decided that no more transmission attempts on either Uu, X2 or S1
interface will be done. Only applicable to DRB packets.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpPktDiscDlPelr
noNotification
nonPersistent Total number of DRB packets (PDCP SDUs) for which no part has been
readOnly transmitted over the air in the downlink that are discarded due to reasons
other than handover or active queue management.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of DRB packets (PDCP SDUs) discarded
due to reasons other than handover or active queue management is
measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 75 of 162
Filter: FDD
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmPdcpPktDiscDlPelrQci
nonUnique
noNotification Total number of DL packets (PDCP SDUs) per QCI that are discarded in the
nonPersistent PDCP layer due to reasons other than handover or active queue
readOnly management. No part of these packets has been transmitted over the air.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of DL packets (PDCP SDUs) per QCI
discarded due to reasons other than handover or active queue management
is measured on PCell.
Compressed: True
Filter: FDD
Condition: The bin accumulates the number of DL PDCP SDUs discarded not
due to HO or active queue management per QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpPktDiscDlPelrUu
noNotification
nonPersistent Total number of packets (PDCP SDUs) for which at least a part has been
readOnly transmitted over the air in the downlink direction but not positively
acknowledged, and it was decided that no more transmission attempts will
be done, due to reasons other than handover. Only applicable to DRB
packets.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of packets (PDCP SDUs) for which at
least a part has been transmitted over the air in the downlink direction but
not positively acknowledged, and it was decided that no more transmission
attempts will be done, due to reasons other than handover, is measured on
PCell.
Filter: FDD
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmPdcpPktDiscDlPelrUuQci
nonUnique
noNotification Total number of DL packets (PDCP SDUs) per QCI for which at least a part
nonPersistent has been transmitted over the air but not positively acknowledged due to
readOnly reasons other than handover, and it was decided that no more transmission
attempts will be done.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of DL packets (PDCP SDUs) per QCI for
which at least a part has been transmitted over the air but not positively
acknowledged due to reasons other than handover, and it was decided that
no more transmission attempts will be done, is measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 76 of 162
Compressed: True
Filter: FDD
Condition: The bin accumulates the number of DL PDCP SDUs that are not
successfully transmitted due to reasons other than HO per QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpPktFwdDl
noNotification
nonPersistent Total number of DRB packets (PDCP SDUs) forwarded to target cell at
readOnly handover for downlink sessions.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of DRB packets (PDCP SDUs) received
by RBS in PDCP in the downlink is measured on PCell.
Filter: FDD
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 77 of 162
Compressed: True
Filter: FDD
Condition: The bin accumulates the number of DL PDCP SDUs received per
QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpPktReceivedUl
noNotification
nonPersistent Total number of DRB packets (PDCP SDUs) received in the uplink.
readOnly
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmPdcpPktReceivedUlQci
nonUnique
noNotification Total number of UL packets (PDCP SDUs) received per QCI.
nonPersistent Compressed: True
readOnly
Condition: The bin accumulates the number of UL PDCP SDUs that are
successfully received per QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpPktTransDl
noNotification
nonPersistent Total number of DRB packets (PDCP SDUs) successfully transmitted (RLC
readOnly acknowledged by UE) in the downlink.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of DRB packets (PDCP SDUs)
successfully transmitted (RLC acknowledged by UE) in the downlink is
measured on PCell.
Filter: FDD
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmPdcpPktTransDlQci
nonUnique
noNotification
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 78 of 162
nonPersistent Total number of DL packets (PDCP SDUs) transmitted successfully per QCI.
readOnly
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). Total number of DL packets (PDCP SDUs) transmitted
successfully per QCI is measured on PCell.
Compressed: True
Filter: FDD
Condition: The bin accumulates the number of DL PDCP SDUs that are
transmitted successfully per QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmPdcpVolDlCmpHdrQci
nonUnique
noNotification The total volume of compressed PDCP SDU headers that has been
nonPersistent transmitted from the Robust Header Compression entity in the downlink
readOnly direction per QCI.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume of compressed PDCP SDU headers
that has been transmitted from the Robust Header Compression entity in
the downlink direction per QCI is measured on PCell.
Compressed: True
Filter: FDD
Condition: Continuous measurement for DRBs aggregated to cell level.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpVolDlDrb
noNotification
nonPersistent The total volume (PDCP SDU) on Data Radio Bearers that has been
readOnly transferred (acknowledged by the UE) in the downlink direction.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transferred (acknowledged by the UE) in the downlink
direction is measured on PCell.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 79 of 162
Compressed: True
Condition: The bin accumulates the DL PDCP SDU volume per QCI that is
transmitted in the last TTI when the buffer for a DRB that maps to the
given QCI is emptied.
Counter type: PDF
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmPdcpVolDlDrbQci
nonUnique
noNotification The total volume (PDCP SDU) that has been transferred (acknowledged by
nonPersistent the UE) on Data Radio Bearers in the downlink direction per QCI.
readOnly
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) that has been
transferred (acknowledged by the UE) on Data Radio Bearers in the
downlink direction per QCI is measured on PCell.
Compressed: True
Filter: FDD
Condition: The counter accumulates acknowledged DL PDCP volume per
QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpVolDlDrbTrans
noNotification
nonPersistent The total volume (PDCP SDU) on Data Radio Bearers that has been
readOnly transmitted in the downlink direction in the PDCP layer.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer is
measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 80 of 162
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN0 is measured on PCell.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN1 is measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 81 of 162
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN2 is measured on PCell.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN3 is measured on PCell.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN4 is measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 82 of 162
by PLMN5.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN5 is measured on PCell.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
that has been transmitted in the downlink direction in the PDCP layer for
the UEs served by PLMN6 is measured on PCell.
Compressed: True
Filter: FDD
Condition: Continuous measurement after Robust Header Compression for
DRBs aggregated to cell level.
Counter type: PDF
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 83 of 162
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Data Radio Bearers
for RLC UM that has been transmitted in the downlink direction in the PDCP
layer is measured on PCell.
Filter: FDD
Condition: Continuous measurement after Robust Header Compression for
DRBs aggregated to cell level
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmPdcpVolDlHdrQci
nonUnique
noNotification The total volume of uncompressed PDCP SDU headers that has been
nonPersistent received in the Robust Header Compression entity in the downlink direction
readOnly per QCI.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume of uncompressed PDCP SDU headers
that has been received in the Robust Header Compression entity in the
downlink direction per QCI is measured on PCell.
Compressed: True
Filter: FDD
Condition: Continuous measurement for DRBs aggregated to cell level.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPdcpVolDlSrb
noNotification
nonPersistent The total number of bits (PDCP SDU) on Signalling Radio Bearers that has
readOnly been transferred (acknowledged by the UE) in the downlink direction.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total number of bits (PDCP SDU) on Signalling
Radio Bearers that has been transferred (acknowledged by the UE) in the
downlink direction is measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 84 of 162
nonPersistent The total volume (PDCP SDU) on Signalling Radio Bearers that has been
readOnly
transmitted in the downlink direction in the PDCP layer.
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The total volume (PDCP SDU) on Signalling Radio
Bearers that has been transmitted in the downlink direction in the PDCP
layer is measured on PCell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 85 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 86 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 87 of 162
Compressed: True
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 88 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 89 of 162
Condition: The bin accumulates the number of PRB pairs used in DL per QCI
for HARQ initial transmissions.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPrbUsedDlFirstTrans
noNotification
nonPersistent The total number of PRB pairs used in DL for HARQ initial transmissions.
readOnly
Condition: The counter accumulates the number of PRB pairs used in DL for
HARQ initial transmissions.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPrbUsedDlMbms
noNotification
nonPersistent The total number of Physical Resource Blocks (PRB) used by MBMS
readOnly transmission in the downlink
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 90 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 91 of 162
Condition: The bin accumulates the number of PRB pairs used in UL per
QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPrbUsedUlSrb
noNotification
nonPersistent The total number of Physical Resource Block (PRB) pairs used for Signaling
readOnly Radio Bearers (SRB) in the uplink.
PDF ranges:
[0]: 0 % <= Utilization < 10 %
[1]: 10 % <= Utilization < 20 %
[2]: 20 % <= Utilization < 30 %
[3]: 30 % <= Utilization < 40 %
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 92 of 162
PDF ranges:
[0]: 0 % <= Utilization < 10 %
[1]: 10 % <= Utilization < 20 %
[2]: 20 % <= Utilization < 30 %
[3]: 30 % <= Utilization < 40 %
[4]: 40 % <= Utilization < 50 %
[5]: 50 % <= Utilization < 60 %
[6]: 60 % <= Utilization < 70 %
[7]: 70 % <= Utilization < 80 %
[8]: 80 % <= Utilization < 90 %
[9]: 90 % <= Utilization
Condition: In a typical case each allocation request is for one CQI resource
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 93 of 162
AND one SR resource; The counter is then increased with one for the
combined allocation request, not one for each resource requested. One
allocation request may also contain request for resources for more than one
UE (a bundled allocation request); Also in this case the counter is only
incremented with one.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmPucchSrCqiResCongCqi
noNotification
nonPersistent The number of times a PUCCH allocation request for CQI resource(s) could
readOnly not be granted
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 94 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 95 of 162
Unit: 1 dBm/PRB
Unit: 1 mW * 2^(-48)
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 96 of 162
long pmRadioRecInterferencePwrPrb11
noNotification
nonPersistent The accumulated interference power for PRB11
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb12
noNotification
nonPersistent The accumulated interference power for PRB12
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb13
noNotification
nonPersistent The accumulated interference power for PRB13
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb14
noNotification
nonPersistent The accumulated interference power for PRB14
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb15
noNotification
nonPersistent The accumulated interference power for PRB15
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb16
noNotification
nonPersistent The accumulated interference power for PRB16
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 97 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 98 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 99 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 100 of 162
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb33
noNotification
nonPersistent The accumulated interference power for PRB33
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb34
noNotification
nonPersistent The accumulated interference power for PRB34
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb35
noNotification
nonPersistent The accumulated interference power for PRB35
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb36
noNotification
nonPersistent The accumulated interference power for PRB36
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb37
noNotification
nonPersistent The accumulated interference power for PRB37
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 101 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 102 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 103 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 104 of 162
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb54
noNotification
nonPersistent The accumulated interference power for PRB54
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb55
noNotification
nonPersistent The accumulated interference power for PRB55
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb56
noNotification
nonPersistent The accumulated interference power for PRB56
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb57
noNotification
nonPersistent The accumulated interference power for PRB57
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb58
noNotification
nonPersistent The accumulated interference power for PRB58
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 105 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 106 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 107 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 108 of 162
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb75
noNotification
nonPersistent The accumulated interference power for PRB75
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb76
noNotification
nonPersistent The accumulated interference power for PRB76
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb77
noNotification
nonPersistent The accumulated interference power for PRB77
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb78
noNotification
nonPersistent The accumulated interference power for PRB78
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb79
noNotification
nonPersistent The accumulated interference power for PRB79
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 109 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 110 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 111 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 112 of 162
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb96
noNotification
nonPersistent The accumulated interference power for PRB96
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb97
noNotification
nonPersistent The accumulated interference power for PRB97
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb98
noNotification
nonPersistent The accumulated interference power for PRB98
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioRecInterferencePwrPrb99
noNotification
nonPersistent The accumulated interference power for PRB99
readOnly
Unit: 1 mW * 2^(-48)
Condition: Samples summed over the measurement period. Measurements
are averaged over receive antennas.One sample per TTI
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..16] pmRadioRecInterferencePwrPucch
nonUnique
noNotification The measured Noise and Interference Power on PUCCH, according to
nonPersistent 36.214.
readOnly
PDF ranges:
[0]: N+I <= -121
[1]: -121 < N+I <= -120
[2]: -120 < N+I <= -119
[3]: -119 < N+I <= -118
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 113 of 162
Unit: 1 dBm/PRB
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 114 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 115 of 162
Filter: FDD
Condition: The counter is incremented when a downlink transmission is
acknowledged on HARQ level (only stepped for secondary component
carrier (SCell) traffic).
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioThpVolDlSelTbs
noNotification
nonPersistent The total successfully transferred data volume on MAC level in the downlink
readOnly for UEs that are considered to be in true radio condition. This counter
includes possible padding bits.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 116 of 162
PDF ranges:
[0]: Transmit diversity
[1]: Open Loop SM Rank 1
[2]: Open Loop SM Rank 2
[3]: Closed Loop SM rank 1
[4]: Closed Loop SM rank 2
Unit: 1 dB
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 117 of 162
long The accumulated sum of all sub-band 10 CQI reported by UEs in the cell for
noNotification
nonPersistent rank 2 transmissions. The average value of the reported sub-band 10 CQI
readOnly within the measurement period can be obtained in conjunction with counter
pmRadioUeRepCqi2SubbandSamp.
The counter is defined according to 32.425.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 118 of 162
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRadioUeRepCqi2Subband1Sum
noNotification
nonPersistent The accumulated sum of all sub-band 1 CQI reported by UEs in the cell for
readOnly rank 2 transmissions. The average value of the reported sub-band 1 CQI
within the measurement period can be obtained in conjunction with counter
pmRadioUeRepCqi2SubbandSamp.
The counter is defined according to 32.425.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 119 of 162
Sub-band CQI value for each codeword. In this case both CQI values shall
be added to the counter and are counted as two samples.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 120 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 121 of 162
Condition: Incremented for each UE aperiodic rank 2 CQI report within the
measurement period.
This counter is for rank 2 (two codewords) CQI reports.
The counter is defined according to 32.425 Section 4.10.1.2
Note for CQI/PMI/RI reporting mode 3-1 or 2-1, there will be a different
Sub-band CQI value for each codeword. In this case, the counter is
incremented twice.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 122 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 123 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 124 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 125 of 162
nonPersistent within the measurement period can be obtained in conjunction with counter
readOnly
pmRadioUeRepCqiSubbandSamp.
The counter is defined according to 32.425.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 126 of 162
Condition: Incremented for each UE aperiodic rank 1 CQI report within the
measurement period.
This counter is for rank 1 (one codeword) CQI reports.
The counter is defined according to 32.425 Section 4.10.1.2
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 127 of 162
nonPersistent The number of CBRA preambles for which no random access response (RA
readOnly
Msg2) was sent due to expiration of the random access response window.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 128 of 162
Unit: 1 ms
Condition: Data in uplink buffer, according to the Buffer Status Report
(BSR) and Token Bucket Counter (TBC) less than 0. Continuous
measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRaUnassignedCfraFalse
noNotification
nonPersistent The number of detected Contention Free Random Access (CFRA, known as
readOnly non-contention based random access in 3GPP term) preambles that are not
allocated to any UE
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 129 of 162
When carrier aggregation is used, the total number of successful RLC PDU
transmissions (ACKs) in the downlink direction is registered on the UE's
primary component carrier (PCell).
Filter: FDD
Condition: Continuous measurement for Radio Bearers aggregated to cell
level.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRlcArqDlNack
noNotification
nonPersistent The total number of unsuccessful RLC PDU and RLC PDU segment
readOnly transmissions (NACKs) in the downlink direction.
Filter: FDD
Condition: Continuous measurement for Radio Bearers aggregated to cell
level.
Counter type: ACC
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRlcArqUlAck
noNotification
nonPersistent The total number of successful RLC PDU transmissions (ACKs) in the uplink
readOnly direction.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 130 of 162
Unit: 1 ms
Condition: The counter represents DL delay per QCI. The DL delay is the
time between reception of a PDCP SDU until it has been scheduled and sent
to the MAC layer for transmission over the air.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRohcEstabFailCid
noNotification
nonPersistent Number of setups of Robust Header Compression failed due to BBM limit.
readOnly
Condition: Triggered at failed activation of Robust Header Compression for
a data radio bearer.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRohcEstabFailLic
noNotification
nonPersistent Number of setups Robust Header Compression failed due to missing or
readOnly inoperable license.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 131 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 132 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 133 of 162
nonPersistent The total number of RRC Connection Request attempts that are considered
readOnly
as re-attempts for Establishment cause High Priority Access.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 134 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 135 of 162
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRrcConnEstabSuccGummeiNative
noNotification
nonPersistent The total number of successful RRC Connection Establishments for GUMMEI
readOnly type equal to native.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 136 of 162
long Number of times the corresponding Sum counter has been incremented.
noNotification
nonPersistent Associated ACC pmCounter pmRrcConnLevSum.
readOnly
Condition: This counter is based on an internal level counter that counts the
number of RRC_CONNECTED UEs that have UL synchronization state: out-
of-sync. Values are read periodically and accumulated.
Counter type: ACC
Sampling rate: 5
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmRrcConnMax
noNotification
nonPersistent Peak number of UE in RRC_CONNECTED mode.
readOnly
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 137 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 138 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 139 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 140 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 141 of 162
Scanner: Primary
Counter is reset after measurement period: Yes
long pmSchedActivityCellDl
noNotification
nonPersistent The aggregated number of ms in which DRB data was required to be
readOnly scheduled in the downlink.
Unit: 1 ms
Condition: Each TTI, the counter shall be incremented when there was a
need to schedule DRB data in the downlink.
Counter type: PEG
Sampling rate: Per ms
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSchedActivityCellUl
noNotification
nonPersistent The aggregated number of ms in which DRB data was required to be
readOnly scheduled in the uplink.
Unit: 1 ms
Condition: Each TTI, the counter shall be incremented when there was a
need to schedule DRB data in the uplink.
Counter type: PEG
Sampling rate: Per ms
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSchedActivityUeDl
noNotification
nonPersistent Total UEs scheduling activity in the downlink.
readOnly
Unit: 1 ms
Condition: The counter shall be increased with 1 for each UE that was
scheduled with SRB/DRB data in the downlink.
Counter type: ACC
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSchedActivityUeUl
noNotification
nonPersistent Total UEs scheduling activity in the uplink.
readOnly
Unit: 1 ms
Condition: The counter shall be increased with 1 for each UE that was
scheduled with SRB/DRB data in the uplink.
Counter type: ACC
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSchedRestrictUeCatDl
noNotification
nonPersistent The sum of the contributions from each UE of the number of ms where
readOnly respective UE is limited in the downlink direction by its UE capability.
Unit: 1 ms
Condition: Each TTI, the counter shall be increased by the number of UEs in
the cell that are limited by their UE capability.
Counter type: ACC
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSchedRestrictUeCatUl
noNotification
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 142 of 162
nonPersistent The sum of the contributions from each UE of the number of ms where
readOnly
respective UE is limited in the uplink direction by its UE capability.
Unit: 1 ms
Condition: Each TTI, the counter shall be increased by the number of UEs in
the cell that are limited by their UE capability.
Counter type: ACC
Sampling rate: Per TTI
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmServiceTimeDrb
noNotification
nonPersistent Number of service seconds aggregated for DRBs in a cell. A DRB is said to
readOnly be ´in service´ from the first data on a DRB (UL or DL) until the last on the
DRB is sent/received.
Unit: 1 s
Condition: Count the time from the first data on the DRB until the last data
on the DRB and sum on the cell level.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmServiceTimeDrbQci
nonUnique
noNotification Number of service seconds aggregated for DRBs mapping to a specific QCI
nonPersistent in a cell. A DRB is said to be ´in service´ from the first data on a DRB (UL
readOnly or DL) until the last on the DRB is sent/received.
[0]: N/A
[1]: Service Time for DRBs mapping to QCI 1
...
[255]: Service Time for DRBs mapping to QCI 255
Compressed: True
Unit: 1 s
Condition: Count the time from the first data on the DRB until the last data
on the DRB associated with the specific QCI and sum on the cell level.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmServiceTimeUe
noNotification
nonPersistent Number of service seconds aggregated for UEs in a cell. A UE is said to be
readOnly ´in service´ if any of its associated DRBs are.
Unit: 1 s
Condition: Count the time when any DRB, associated with the UE, is in
service.
Counter type: ACC
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSessionTimeDrb
noNotification
nonPersistent This counters shows the accumulated active session time for all DRBs in a
readOnly cell.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 143 of 162
Unit: 1 seconds
Condition: Number of session seconds aggregated for DRBs in a cell. A DRB
is said to be ´in session´ if data on a DRB (UL or DL) has been transferred
during the last 100 ms.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..256] pmSessionTimeDrbQci
nonUnique
noNotification The session time aggregated for DRBs mapping to a QCI.
nonPersistent Compressed: True
readOnly
Unit: 1 seconds
Condition: The bin accumulates session seconds aggregated for DRBs with
a certain QCI. The DRBs for a UE is said to be "in session" if any data on
any DRB (UL or DL) has been transferred during the last 100 ms for that
QCI.
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmSessionTimeUe
noNotification
nonPersistent This counters shows the accumulated active session time for all UEs in a
readOnly cell.
Unit: 1 s
Condition: Number of session seconds aggregated for all UEs in a cell. A UE
is said to be ´in session´ if any data on a DRB (UL or DL) has been
transferred during the last 100 ms
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long[0..8] pmSinrPucchDistr
nonUnique
noNotification Distribution of the SINR values calculated for PUCCH .
nonPersistent
readOnly PDF ranges:
[0]: SINR <= -15
[1]: -15 < SINR <= -12
[2]: -12 < SINR <= -9
[3]: -9 < SINR <= -6
[4]: -6 < SINR <= -3
[5]: -3 < SINR <= 0
[6]: 0 < SINR <= 3
[7]: 3 < SINR
Unit: 1 dB
Condition: Each SINR value for PUCCH per UE calculated on a TTI basis
yields one sample in the distribution.
Counter type: PDF
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..8] pmSinrPuschDistr
nonUnique
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 144 of 162
Unit: 1 dB
Condition: Each SINR value for PUSCH per UE calculated on a TTI basis
yields one sample in the distribution.
Counter type: PDF
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmTtiBundlingUeMax
noNotification
nonPersistent Maximum sample value of number of UEs using TTI Bundling.
readOnly
Filter: FDD
Condition: The counter is set to the peak value of samples of number of
UEs using TTI Bundling.
Counter type: GAUGE
Sampling rate: 5
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmTtiBundlingUeSamp
noNotification
nonPersistent Counts the number of times the corresponding pmTtiBundlingUeSum has
readOnly accumulated a new sample.
Filter: FDD
Condition: The counter is incremented by one each time a sample value is
accumulated in pmTtiBundlingUeSum.
Counter type: SCAN
Sampling rate: 5
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmTtiBundlingUeSum
noNotification
nonPersistent Sum of all sample values recorded for number of UEs using TTI Bundling.
readOnly
Filter: FDD
Condition: The counter accumulates values of the number of UEs using TTI
Bundling from each sampling occasion.
Counter type: ACC
Sampling rate: 5
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..5] pmUeCategoryDistr
nonUnique
noNotification A distribution of the UE capability parameter UeCategory for established UE
nonPersistent contexts.
readOnly
PDF ranges:
[0]: ueCategory = 1
[1]: ueCategory = 2
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 145 of 162
[2]: ueCategory = 3
[3]: ueCategory = 4
[4]: ueCategory = 5
Condition: If there was data in the buffer at the time of release, then at
reception of S1 message UE Context Release Command with internal cause
codes considered abnormal (Radio Connection with UE is lost; Handover
failure for the UE; UE pre-emption) when the RBS initiated the release. It
can also be stepped at transmission of UE Context Release Request or
Reset message by the RBS, or when a cell owned by that RBS is disabled
(and that leads to internal RBS UE Context Release).
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long pmUeCtxtRelAbnormalEnbActCdt
noNotification
nonPersistent Counts the total number of abnormal UE context releases by the eNodeB
readOnly due to cell down time (manual intervention) when data was in either the UL
or DL buffer (i.e. active).
Condition: Stepped for each UE that is lost due to cell down time (manual
intervention).
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 146 of 162
Condition: If there was data in the buffer at the time of release, and the
release is due to that executed handover fails and the UE is considered
dropped.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelAbnormalEnbActPe
noNotification
nonPersistent The total number of abnormal UE context releases initiated by the RBS due
readOnly to pre-emption and that there was data in either the UL or DL buffer (i.e.
active).
Condition: If there was data in the buffer at the time of release of an E-RAB
and due to that the S1 interface is lost, S1 bearer error indication is
received or SGW failure is detected.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelAbnormalEnbActUeLost
noNotification
nonPersistent The total number of abnormal UE Context releases by the RBS due that the
readOnly radio connection with the UE is lost and that there was data in either the UL
or DL buffer (i.e. active).
Condition: If there was data in the buffer at the time of release and if there
was a release of an UE due to that the radio connection towards the UE is
lost (i.e. UE unreachable by the RBS).
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelAbnormalEnbLic
noNotification
nonPersistent The total number of abnormal UE Contexts Releases initiated by the RBS
readOnly due to license reject.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 147 of 162
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelAbnormalEnbPe
noNotification
nonPersistent The total number of abnormal UE Context releases initiated by the RBS due
readOnly to pre-emption. The counter is stepped regardless of whether data was or
was not lost in UL/DL buffers.
Condition: there was data in the buffer at the time of release, then stepped
at reception of S1 message UE Context Release Command , if the cause
was regarded as abnormal, and the release is MME initiated.
Counter type: PEG
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmUeCtxtRelCsfbCdma1xRtt
noNotification
nonPersistent Number of RRC Connection Release with redirect to CDMA2000 1xRTT
readOnly triggered by CS Fallback
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 148 of 162
Condition: CS Fallback has been initiated and a target cell for handover has
been determined, but handover preparation has failed.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelCsfbHoPrepFail1xRttEm
noNotification
nonPersistent Number of times a CS Fallback Emergency Call has been triggered where
readOnly the UE should be doing a handover to a cell found by measurements, the
handover preparation failed and the UE was redirected to a CDMA2000
1xRTT frequency
Condition: CS Fallback Emergency Call has been initiated and a target cell
for handover has been determined, but handover preparation has failed.
Counter type: PEG
Sampling rate: -
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 149 of 162
Condition: CS Fallback has been initiated for the UE and the UE has
searched for, but failed to find, a target cell for handover and the
measurement has timed out.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelCsfbMeasTO1xRttEm
noNotification
nonPersistent Number of times a CS Fallback Emergency Call has been triggered where
readOnly the UE should be doing a handover to a cell found by measurements, the
measurement failed to find a target cell, and the UE was redirected to a
CDMA2000 1xRTT frequency
Condition: CS Fallback Emergency Call has been initiated for the UE and the
UE has searched for, but failed to find, a target cell for handover and the
measurement has timed out.
Counter type: PEG
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelCsfbTdScdma
noNotification
nonPersistent The number of RRC Connection Release with redirect to TD-SCDMA
readOnly triggered by CS Fallback.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 150 of 162
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message UE Context Release Command (except
if the cause was successful handover). The release must also have been
MME initiated.
Counter type: PEG
Scanner: Primary
Counter is reset after measurement period: Yes
long pmUeCtxtRelNormalEnb
noNotification
nonPersistent The total number of normal UE Context Releases triggered by RBS. The
readOnly counter is stepped regardless of whether data was or was not lost in UL/DL
buffers.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 151 of 162
Condition: If there was data in the buffer at the time of release, then
stepped at reception of S1 message UE Context Release Command when
internal cause codes considered normal (Successful Handover, User
Inactivity, Inter-RAT redirection, CS Fallback Triggered) when the RBS
initiated the release.
Counter type: PEG
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmUeCtxtRelNormalEnbTuneOut
noNotification
nonPersistent The total number of normal UE Context Releases initiated by the RBS for
readOnly Tune-out UEs. The counter is stepped regardless of whether data was or
was not lost in UL/DL buffers
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 152 of 162
PDF ranges:
[0]: 0 < DL UE thp sample < 1.000
[1]: 1.000 <= DL UE thp sample < 5.000
[2]: 5.000 <= DL UE thp sample < 10.000
[3]: 10.000 <= DL UE thp sample < 20.000
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 153 of 162
Unit: 1 kbps
When carrier aggregation is used, a PDCP SDU can be sent over multiple
cells (PCell/SCell(s)). The effective DL transport time, comprising those
periods from when the first part of the PDCP SDU of the DL buffer was
transmitted on Uu until the buffer is emptied, excluding the TTI emptying
the buffer, is registered on PCell.
Unit: 1 ms
Filter: FDD
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmUeThpTimeUl
noNotification
nonPersistent The UL volume transfer time used for UL UE Throughput. It comprises of
readOnly time periods from when the 5th MAC SDU data reception of an UL buffer
transfer on Uu until the buffer is emptied, excluding the TTI emptying the
buffer.
Unit: 1 ms
Condition: Continuous measurement for UEs aggregated to cell level.
Counter type: ACC
Sampling rate: -
Scanner: Primary
Counter is reset after measurement period: Yes
long pmUeThpTimeUlRs
noNotification
nonPersistent The time where the UE have uplink data in a buffer and End-user bitrate
readOnly shaping functionality will prohibit transmission in the uplink.
Unit: 1 ms
Deprecated: Since L12A. Has no functional behaviour. Planned to be
removed.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 154 of 162
PDF ranges:
[0]: 0 < UL UE thp sample < 1.000
[1]: 1.000 <= UL UE thp sample < 3.000
[2]: 3.000 <= UL UE thp sample < 5.000
[3]: 5.000 <= UL UE thp sample < 10.000
[4]: 10.000 <= UL UE thp sample < 20.000
[5]: 20.000 <= UL UE thp sample < 30.000
[6]: 30.000 <= UL UE thp sample < 60.000
[7]: 60.000 <= UL UE thp sample
Unit: 1 kbps
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 155 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 156 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 157 of 162
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long[0..256] pmZtemporary18Qci
nonUnique
noNotification Compressed: True
nonPersistent
readOnly Condition: -
Counter type: PDF
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmZtemporary19
noNotification
nonPersistent Normally this counter is not used, it can however sometimes be temporarily
readOnly used for very late additions in a release. If so, for description see Network
Impact Report in the CPI.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 158 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 159 of 162
Sampling rate: -
Scanner: Not included in any predefined scanner
Counter is reset after measurement period: Yes
long pmZtemporary30
noNotification
nonPersistent Normally this counter is not used, it can however sometimes be temporarily
readOnly used for very late additions in a release. If so, for description see Network
Impact Report in the CPI.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 160 of 162
nonPersistent Normally this counter is not used, it can however sometimes be temporarily
readOnly
used for very late additions in a release. If so, for description see Network
Impact Report in the CPI.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 161 of 162
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018
class EUtranCellFDD Page 162 of 162
long pmZtemporary69
noNotification
nonPersistent Normally this counter is not used, it can however sometimes be temporarily
readOnly used for very late additions in a release. If so, for description see Network
Impact Report in the CPI.
http://localhost:9032/alexserv?AC=LINK&ID=8618&FN=15554-EN_LZN7850001_1-... 7/18/2018