Professional Documents
Culture Documents
Offcon DNV Zorro Skid
Offcon DNV Zorro Skid
About OffCon: OffCon is an MS EXCEL based checklist and calculation tool for verification of the design of
offshore containers. This program does not include any detailed analysis of the container framework. Detailed
frame analysis may be performed using DNV 3-D Beam or other beam calculation programs.
The program is copyright by Det Norske Veritas, and is based on the rule requirements of DNV Standard for Certification
2.7-1 January 2006. The program is available for clients applying for offshore container certification at DNV. Feedback and
comments are appreciated: e-mail: MTPNO876@dnv.com.
Identification
Client Project No.
Project Name 0
Calculations
14. Four point lift: 2,5xR (Only primary structure included)
15. Two point lift: 1,5xR for open frames (incl. all structure)
16. Fork pocket lift: 1,6xR
17. Frame analysis carried out (computer analysis)
18. Padeye stresses
19. Impact loads
20. Floor plate stress from internal loading: 2,5xP/A
21. Wall stress from internal loading: 0,6xP/A
22. Strength of intermediate deck
23. IMDG Requirements (DG tank containers)
Other Comments:
Beam span
L= 4343 mm
Yield strength of material
Re = 324 N/mm2
Maximum bending stress and deflections due to simulated impact in middle of span
Other frame members of the side structure, including top rails: F = 0,15*R*g
Length Bending stress (N/mm2) Deflections (mm) Max. Allowable
deflection L/250 (mm) *
fixed - fixed fixed - free free-free fixed - fixed fixed - free free-free
3843 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 15.37
4343 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 17.37
4843 #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 19.37
Padeye Design
Client: 0 Time: 15:32
Project: 0 Date: 18.08.13
Project No.: 0
Reference: Section 4.2.3.1 Lifting with lifting set and Appendix D. Design of pad eye.
Calculated stresses
Tear out stress N/mm2
Contact stress, 6% clearence N/mm2 Steel only
Shackle dimensions
Minimum bolt diameter
Dmin = 0,94xDh = 0.00 mm
Check if the pad eye input is suitable to any shackle as listed in EN 13889:2000
Remember that this check only give a preliminary indication if the pad eye is matching the shackle based
on pin diameter and pad eye thickness. Always remember to manualy verify that shackle and pad eye
geometry match. These calculation only check against Dee and Bow shackles listed in Table 2 in the EN
13889:2000 standard. Other dimensions may be acceptable
-> Approved services -> Products and Manufacturers-> Type Approval -> Containers, Cargo Handling, Lifting
Appliances and Miscellaneous Equipment (S) -> Lifting Sets
Lifting Set Calculations
Client: 0 Time: 15:32
Project: 0 Date: 18.08.13
Project No.: 0
http://exchange.dnv.com/
-> Approved services -> Products and Manufacturers-> Type Approval -> Containers, Cargo Handling, Lifting
Appliances and Miscellaneous Equipment (S) -> Lifting Sets
Special lifting set calculations
Client: 0 Time 15:32
Project: 0 Date 18.08.13
Project No.: 0
These calculations are for containers where the centre of gravity is offset along one axis
Rating 13608 kg
Enhancement factor x #VALUE! Table 8.1
Working Load Limit = #VALUE!
Semi-symmetric slings
a= mm
b= mm
w= mm
h= mm
If these values are modified after pad eyes calculation ,
remember to recheck pad eyes
g1= #VALUE! °
g2= #VALUE! °
a1= #VALUE! °
a2= #VALUE! °
Master link
Quad Assembly ( Masterlink + Intermediate links requirements
Load on quad assembly #VALUE!
Forerunner requirements Fore runner
Load on forerunner #VALUE!
Wirerope sling, fibre core EN 13414-1 #VALUE!
Wirerope sling, steel core EN 13414-1 #VALUE! Quad assembly
Chain sling EN 818-4 #VALUE!
Sling leg requirements g1 g2
Load per sling leg #VALUE! #VALUE!
Wirerope sling, fibre core EN 13414-1 #VALUE! #VALUE!
Wirerope sling, steel core EN 13414-1 #VALUE! #VALUE!
Chain sling EN818-4 #VALUE! #VALUE! β Sling leg
Shackle requirements g1 g2
Load on each shackle #VALUE! #VALUE!
Required shackle EN 13889 #VALUE! #VALUE!
Shackle
http://exchange.dnv.com/
-> Approved services -> Products and Manufacturers-> Type Approval -> Containers, Cargo Handling, Lifting
Appliances and Miscellaneous Equipment (S) -> Lifting Sets