Professional Documents
Culture Documents
Installation Instructions: Parts List
Installation Instructions: Parts List
com
Accessory Application Publications No.
VERSION 1
INSTALLATION FOG LIGHTS 2016 HR-V
Issue Date
INSTRUCTIONS P/N 08V31-T7S-100
APR 2015
Relay
13 Wire ties
10 Self-tapping screws
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 08V31-T7S-1000-90 1 of 20
www.collegehillshonda.com
Fuse label TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Ratchet
10 mm Socket
Diagonal cutters
Blanket
15A Fuse Tape
Isopropyl alcohol
Shop towel
The following tools are available through the Honda Tool
and Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter
the number under “Search”. Or, call 888-424-6857.
2 Aluminum tapes • Plastic Trim Tool (T/N SILTRIMTL10)
• Trim Tool Set (T/N SOJATP2014)
Illustration of the Fog Lights Installed on the Vehicle
SWITCH COMBINATION
HARNESS LIGHT SWITCH
Clip
(May not used)
INSTALLATION
2 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
2. Lower the steering wheel. Attach tape to the upper 4. Turn the steering wheel 180° counterclockwise.
column cover as shown. Using a plastic trim tool, release the retaining tab.
STEERING
WHEEL
UPPER
COLUMN
COVER
UPPER
TAPE COLUMN
COVER
PLASTIC
TRIM TOOL
UPPER COLUMN
COVER
QD41005AJ
RETAINING
TAB
PLASTIC
TRIM TOOL
QD41003AJ
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 3 of 20
www.collegehillshonda.com
6. Remove the one self-tapping screw from the lower 8. Pull away the door opening seal, and remove the
column cover. driver’s dashboard side lid.
DOOR
OPENING
SEAL
(Pull away.)
LOWER
COLUMN 6 RETAINING
COVER SELF-TAPPING QD41006AJ TABS
SCREW DRIVER’S
DASHBOAR
D SIDE LID
7. Turn the steering wheel 180° clockwise, and remove
the one self-tapping screw from the lower column PLASTIC
TRIM TOOL QD40315AJ
cover.
9. Attach the tape to the lower column cover.
SELF-TAPPING
LOWER SCREW
COLUMN
COVER QD41007AJ
TAPE QD40316AJ
LOWER COLUMN
COVER
4 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
10. Pull away the door opening seal, and remove the • Wrap a shop towel around the lever.
driver’s dashboard lower cover and unplug the • Attach tape to the areas shown on each side.
vehicle connectors.
SHOP TOWEL
DOOR OPENING SEAL
(Pull away.) LEVER
CLIP
VEHICLE
CONNECTORS
HEAD
LIGHT
DRIVER’S DASHBOARD
11 CLIPS LOWER COVER QD41009AJ FRONT
FENDER
11. Remove the lower column cover.
TAPE
FRONT BUMPER
9 CLIPS
GRILLE COVER
LOWER COLUMN
SELF-TAPPING COVER
SCREW QD41402AJ
FRONT BUMPER
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 5 of 20
www.collegehillshonda.com
• Remove the front wheel arch protector on each
side.
5 CLIPS
2 CLIPS
2 SELF-TAPPING
SCREWS
4 CLIPS
QC72104AH
6 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
• Remove one self-tapping screw on each side. • Release the four retaining tabs on each side.
SELF-TAPPING 1 3 RETAINING
SCREW TABS
FRONT BUMPER
2 RETAINING
TAB
FRONT
BUMPER
FRONT
BUMPER
QD41504AH
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 7 of 20
www.collegehillshonda.com
• With the help of an assistant, remove the front 13. Remove the front bumper lower grille from the front
bumper. Place the front bumper on the blanket bumper.
to prevent damage.
4 RETAINING
TABS
2 RETAINING TABS
FRONT
BUMPER
FRONT BUMPER
LOWER GRILLE
FRONT BUMPER
2 SELF-
D41599AH
TAPPING
SCREWS
6 RETAINING
6 RETAINING TABS QD42002AH
TABS
8 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Installing the Fog Lights 16. Install the left fog light bracket to the left fog light trim.
14. Remove the left bumper trim from the front bumper.
6 RETAINING
TABS LEFT FOG LIGHT TRIM
FRONT BUMPER
3 SELF-TAPPING
SCREWS QD42004AH
17. Install the left fog light trim to the front bumper.
SELF-TAPPING
SCREW FRONT 6 RETAINING
LEFT BUMPER TRIM BUMPER TABS
(Discard.)
QD42003AH
15. Install the left fog light on the left fog light bracket
with two self-tapping screws.
SELF-TAPPING
SCREW
(reused)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 9 of 20
www.collegehillshonda.com
Routing the Fog Light Harness 22. Secure the fog light harness 1-pin connector to the
vehicle harness with one wire tie.
20. Route the fog light harness as shown.
FOG LIGHT
HARNESS FOG LIGHT HARNESS QD42007BH
23. Install the fog light harness ground terminal with one
ground bolt.
21. Plug the vehicle 1-pin connector into the fog light
harness 1-pin connector.
GROUND BOLT
10 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
24. Secure the fog light harness to the vehicle harness 26. Secure the fog light harness clip to the hole in the
with one wire tie. vehicle frame as shown.
FOG LIGHT
HARNESS
25. Align the branch of fog light harness with the branch 27. Route the fog light harness as shown. Secure the fog
of vehicle harness, and secure the fog light harness light harness clip to the hole in the vehicle frame as
to the vehicle harness with three wire ties. shown.
VEHICLE
HARNESS FOG LIGHT QD42012AH
FOG LIGHT BRANCH OF QD42010BH HARNESS
HARNESS FOG LIGHT
HARNESS
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 11 of 20
www.collegehillshonda.com
28. Secure the fog light harness to the vehicle harness 30. Using isopropyl alcohol on a shop towel, clean the
with one wire tie. bumper beam where the aluminum tape will attach.
VEHICLE
HARNESS
32. Plug the two fog light harness 2-pin connectors into
each fog light, and with the help of an assistant,
reinstall the front bumper.
2 JOINED
LONG
WIRE TIES
BUMPER
BEAM
FOG
LIGHT
2 LONG HARNESS
WIRE TIES
(Joint.)
QD42014AH RIGHT
FOG LIGHT
12 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Routing the Switch Harness 35. Install the clip to the switch harness relay block.
Secure the switch harness relay block to the hole in
33. Install the relay into the switch harness relay block.
the vehicle frame. If another relay block is already
secured to the hole in the vehicle frame, secure the
RELAY
switch harness relay block into other relay block.
VEHICLE
FRAME
SWITCH
HARNESS
RELAY BLOCK
SWITCH HARNESS
RELAY BLOCK
CLIP
QD42017BH
VEHICLE 1-PIN
CONNECTOR
SWITCH HARNESS
SWITCH HARNESS RELAY BLOCK
1-PIN CONNECTOR
STEERING SHAFT
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 13 of 20
www.collegehillshonda.com
36. Align the branch of switch harness with the branch of 38. Secure the switch harness to the vehicle harness
vehicle harness, and secure the switch harness to with one wire tie.
the vehicle harness with two wire ties.
VEHICLE
HARNESS WIRE TIE
BRANCH OF
VEHICLE HARNESS 2 WIRE TIES
SWITCH
HARNESS SWITCH
VEHICLE BRANCH OF HARNESS
HARNESS SWITCH HARNESS
37. Secure the switch harness to the vehicle harness Without Other Accessory Harness 4-pin
with three wire ties. Connector Plugged Into The Fuse Box.
39. Plug the switch harness 4-pin connector into the fuse
SWITCH VEHICLE box. Go to step 41.
HARNESS 3 WIRE TIES
HARNESS
FRONT VIEW
Plug in here.
FUSE BOX
SWITCH
HARNESS
4-PIN
CONNECTOR
14 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
With Other Accessory Harness 4-pin Connector Without Other Accessory Harness 8-pin
Plugged Into The Fuse Box. Connector Plugged Into The Fuse Box.
40. If another accessory harness 4-pin connector is 41. Plug the switch harness 8-pin connector into the fuse
plugged into the fuse box, plug the switch harness 4- box. Go to step 44.
pin connector into the other accessory harness 4-pin
connector. FRONT VIEW
Plug in SWITCH HARNESS
here. 8-PIN CONNECTOR
OTHER ACCESSORY
HARNESS
4-PIN CONNECTOR
FRONT VIEW
OTHER ACCESSORY HARNESS
4-PIN CONNECTOR
FUSE BOX
FUSE BOX
SWITCH
HARNESS
4-PIN
CONNECTOR
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 15 of 20
www.collegehillshonda.com
With Other Accessory Harness 8-pin Connector 44. Secure the switch harness to the vehicle harness
Plugged Into The Fuse Box. with one wire tie.
FUSE BOX
OTHER ACCESSORY
HARNESS
8-PIN CONNECTOR
QD42028AH
SWITCH HARNESS
8-PIN CONNECTOR
STEERING
WHEEL
43. Plug the switch harness 8-pin connector into the fuse Do not pull
box. on the lever.
VEHICLE
CONNECTOR
FRONT VIEW
Plug in SWITCH HARNESS
here. 8-PIN CONNECTOR
FUSE BOX
16 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
47. Install the new combination light switch on the 50. Using isopropyl alcohol on a shop towel, clean the
steering column. lower column cover where the fuse label will attach.
NOTE: Do not push on the lever when installing the
switch.
ATTACHING
FUSE LABEL
(15A OPTION FUSE)
STEERING
WHEEL
Do not push
on the lever.
VEHICLE LOWER
CONNECTOR COLUMN COVER
Clean with
isopropyl alcohol.
QC33139CH
NEW COMBINATION 2 RETAINING TABS QD42030AH 52. Remove the relay box cover.
LIGHT SWITCH (Push.)
RELAY BOX
49. Plug the 15A fuse into the fuse box. COVER
FRONT VIEW
CONNECTING
LOCATION
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 17 of 20
www.collegehillshonda.com
53. Using isopropyl alcohol on a shop towel, clean the Check to Operate of the Fog Lights
relay box cover.
• Turn the headlight switch to the “ ” position
(headlights on low beam).
FUSE LABEL
• Turn on the fog light switch (indicator is on).
• If the fog lights do not turn on, check the fuse and all the
ATTACHING connectors including the ground cable.
RELAY BOX
COVER
FOG LIGHT
OFF - - - -
SWITCH
- - ON -
QC51302BH
QC00130AH
18 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
Fog Light Aiming Adjustment 2. Unplug the fog light harness connector.
61. Adjust the fog lights:
• Adjust the aim according to your local laws and
regulations.
FOG LIGHT
• To adjust, turn the adjustment point in or out until HARNESS
the correct aim is obtained. CONNECTOR
LEFT
FOG LIGHT
BULB
(Turn.)
To To
raise. QC73038AH
lower.
PHILLIPS QC73035BH
SCREWDRIVER
BULB REPLACEMENT
1. Remove the two clips, and tuck the left front inner
fender as shown.
LEFT FRONT
INNER
FENDER
(Tuck.)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved. AII01797-24 (1504) 19 of 20
www.collegehillshonda.com
4. Install the new fog light bulb.
• Use only a genuine Honda halogen light bulb
with specified wattage.
Rating: 12V 35W H8 Halogen Light Bulb
P/N 33165-TL0-003
• Do not touch the bulb. Oily or greasy substances
on the bulb can shorten its service life due to the
heat produced when the bulb is turned on. If the
bulb is accidentally touched, wipe it clean with a
soft cloth that has been dampened with a
denatured alcohol or a mild detergent solution.
• When installing the new bulb, align the cutout on
the fog light with the tab on the new bulb and turn
the new bulb in completely. If not properly
aligned, the fog light may annoy the oncoming
driver’s view.
NEW BULB
20 of 20 AII01797-24 (1504) © 2015 American Honda Motor Co., Inc. – All Rights Reserved.