Professional Documents
Culture Documents
Bta41 600B PDF
Bta41 600B PDF
40 A standard TRIACs
Features A2
Applications
■ On/off function in static relays, heating
RD91 insulated
regulation, induction motor starting circuits
(BTA40)
■ Phase control operations in light dimmers,
motor speed controllers, and similar A2
Description A1
A2 A1
G
Available in high power packages, the A2
G
1 Characteristics
I - II - III 50
IGT (1) MAX. mA
VD = 12 V RL = 33 Ω IV 100
VGT ALL MAX. 1.3 V
VGD VD = VDRM RL = 3.3 kΩ Tj = 125 °C ALL MIN. 0.2 V
IH (2) IT = 500 mA MAX. 80 mA
I - III - IV 70
IL IG = 1.2 IGT MAX. mA
II 160
dV/dt(2) VD = 67% VDRM gate open Tj = 125 °C MIN. 500 V/µs
(2)
(dV/dt)c (dI/dt)c = 20 A/ms Tj = 125 °C MIN. 10 V/µs
1. Minimum IGT is guaranted at 5% of IGT max.
2. for both polarities of A2 referenced to A1
IDRM Tj = 25 °C 5 µA
VDRM = VRRM MAX.
IRRM Tj = 125 °C 5 mA
1. Minimum IGT is guaranted at 5% of IGT max.
2. for both polarities of A2 referenced to A1
Figure 1. Maximum power dissipation versus Figure 2. On-state rms current versus case
on-state rms current (full cycle) temperature (full cycle)
P(W) IT(RMS)(A)
50 45
α=180°
40
BTB41
40 35 BTA40
BTA41
30
30
25
20
20
15
180°
α 10
10
α 5 TC(°C)
IT(RMS)(A)
0 0
0 5 10 15 20 25 30 35 40 0 25 50 75 100 125
100
Tj = Tj max.
1.E-01
Zth(j-a)
BTA / BTB41
Tj = 25°C.
10
1.E-02
VTM(V)
1.E-03
tp(s) 1
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 1.E+02 1.E+03
Figure 5. Surge peak on-state current versus Figure 6. Non-repetitive surge peak on-state
number of cycles current for a sinusoidal pulse and
corresponding value of I2t
2 2
ITSM(A) ITSM(A), I t (A s)
450 10000
Tj initial=25 °C
400 dI/dt limitation: Pulse width tp < 10 ms
50A/µs ITSM
350 t=20ms
I2t
Non repetitive
Tj initial=25°C One cycle
300 1000
250
200
150 Repetitive
TC=70°C
100
50
Number of cycles tp(ms)
0 100
1 10 100 1000 0.01 0.10 1.00 10.00
Figure 7. Relative variation of gate trigger, Figure 8. Relative variation of critical rate of
holding and latching current versus decrease of main current versus
junction temperature (dV/dt)c (typical values)
1.8
2.0
1.6
IGT
1.5 1.4
IH & IL 1.2
Typical values
1.0 1.0
0.8
0.5
0.6
Tj(°C) (dV/dt)c (V/µs)
0.0 0.4
-40 -20 0 20 40 60 80 100 120 140 0.1 1.0 10.0 100.0
Figure 9. Relative variation of critical rate of decrease of main current versus (dV/dt)c
1
Tj(°C)
0
0 25 50 75 100 125
TRIAC series
Insulation
A = insulated
B = non-insulated
Current
40 = 40 A in RD91
Voltage
600 = 600 V
800 = 800 V
Sensitivity and type
B = 50 mA standard
Packing mode
RG = Tube
Blank = Bulk
3 Package information
R B
A 4.4 4.6 0.173 0.181
ØL
B 1.45 1.55 0.057 0.061
C2 C1
B2 - 24.00 - 0.945
A1
C - 14.00 - 0.551
C1 - 3.50 - 0.138
N2 N1
C2 1.95 3.00 0.077 0.118
B
F E3 0.70 0.90 0.027 0.035
F 4.00 4.50 0.157 0.177
E3
I I 11.20 13.60 0.441 0.535
A
L1 3.10 3.50 0.122 0.138
L2 1.70 1.90 0.067 0.075
N1 33° 43° 33° 43°
N2 28° 38° 28° 38°
4 Ordering information
5 Revision history
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.