Professional Documents
Culture Documents
V686K Explore - WIFI Quadcopter
V686K Explore - WIFI Quadcopter
V686K Explore - WIFI Quadcopter
Specifications
CONTENTS OF THE BOX: SPECIFICATIONS:
Security precautions
• Read the manual carefully and completely
• This model is not suitable for children under 14 years and contains small parts
• Children should only use this model under the supervision of an adult
• Keep hands, face, hair and clothes away from blades.
• Stand out of reach of moving parts of the copter
• After using the copter ALWAYS disconnect the battery and remove it from the device
• The model and the transmitter must be switched off after use
• Always fly in an open and safe environment where you will not cause any danger to others
• For the remote control, we recommend AA batteries with a voltage of 1.5 to 1.2 volts
• For people without experience, we recommend that you learn to fly with an experienced user during your first flights
• Before each flight, test the distance limit of the transmitter
• Keep these instructions safe
• Always follow local laws and regulations! Contact your reseller when in doubt.
Battery charging
1. Charging wire
2. LED
3. Li-po Battery
Plug the charger into a wall socket and connect the battery to
the charger. This can only be done in one way: by firmly
connecting the charging cable. If the green light is on, the
battery is fully charged and can be disconnected. Then do not
forget to unplug the charger from the wall socket.
Input : 220V
Charging Current : 500mA
Full Voltage: 4.2 +/- 0.03V
Warning : Always place the battery on a heat resistant surface and never leave it unattended!
- Using the throttle you can control the rotation axis of the drone. Using the directional joystick you can control the flight direction
of the drone.
- The mode available on this model is the mode 2 with the layout of the throttle on left. It is not possible to switch mode on this
model.
- The different calibration buttons help keep the drone stationary. Test this by pressing the accelerator and calibration buttons to
maintain the drone in one place.
- You can choose the percentage of the speed. The higher the value, the faster the reaction will be (e.g. 100% will be more
responsive than 40%).
- The two module buttons are used to activate different modules : photos / shots / basket.
Headless mode
Headless Mode Operation : Straighten the copter (red blades are in front) , long press Headless Mode button 2 seconds to enter
into Headless Mode, the transmitter will start beeping; Long press Headless Mode button 2 seconds to exit, the transmitter will
stop beeping.
How to fly
Flying is really simple, but you need a little practice at first. Connect to www.wltoys.eu to watch educational films.
SIDEWARD
FORWARD
ALTITUDE
Pushing the gear lever from side to side, the drone will turn
on its own axis.
Never go full speed for the first 3 flights. After 3 flights, blow out engines with air when possible.
Spare engines can be bought on www.wltoys.eu or with your reseller.
CAUTION
- Ensure that the copter in flight is always within sight and under control.
- Always use a fully charged battery.
- When finished flying, always turn off the copter first, then the remote control.
- Do not use the copter when it has visible or mechanical damage.
- Always fly in an open and Jellyfished environment to avoid dangerous situations.
- Always stay out of reach of rotors.
- Remember to disconnect the battery of the copter after each flight.
- Ensure that you adhere to all the legal requirements that exist for your copter model in the country in which you are using it.
- If you lose control of the copter, disable the propulsion of the engines immediately by pushing the throttle lever down to turn it off.
Calibration
Note: The calibration is done in the factory, it is usually not necessary to do it when you receive the product.
Troubleshooting
1. The receiver LED blinks continuously for more than 4 seconds after the quadcopter battery have been inserted. No response to
the command input. The transmitter is not connected to the device. Repeat the power-on initialization process.
2. No response from the quadcopter after the battery have been connected. There is probably contact failure on the battery
terminals. Turn on the transmitter and ensure that the battery of the vehicle is correctly inserted. Replace the battery and ensure
good contact at the battery's connections. Use fully charged batteries in the remote.
3. The motor does not respond to the throttle stick and the receiver flashes. The quadcopter's battery is exhausted. Charge the
battery or replace it with a charged battery.
4. The main rotor continues to rotate after landing. Confirm that the gear lever is oriented downward.
5. The main rotor rotates but the device does not take off. The blades may be distorted or the quadcopter battery is exhausted.
Charge or replace with a fully charged battery and / or replace the blades.
6. The quadcopter suffers of strong vibrations. The blades are distorted. Replace the blades.
7. The tail is not balanced after adjusting the clip or speed is inconsistent in the left / right pirouette. Tail rotors are probably
damaged. Replace the main wing and / or the main engine.
8. The quadcopter was still moving forward after the adjustment of the levers during hover. The gyroscope is not correctly
calibrated. The gear lever is placed too high or too low. The boot refines the calibration therefore restart on a flat surface.
9. You can not fly, the helicopter falls. The motor is probably fall out or the gears are loose. Reinstall the motor and tighten the
gears.
Spare parts
The copter is not sensitive to crashes, but in case of extreme drops it is possible that some parts may break. All parts can be
ordered and easily assembled. Please contact your dealer or visit www.wltoys.eu for more information.
105 | Bearing | 8
123 | Gear | 4
125 | Main shaft | 4
415 | Blades | 4
421 | Battery | 1
422 | Protect part | 4
641 | Upper canopy | 1
642 | Battery cover | 1
643 | Lower canopy | 1
644 | Landing skid | 2
645 | Lamp cover | 4
646 | Back lamp cover | 1
649 | PCB | 1
650 | Red light | 2
651 | Motor clockwise | 2
652 | Motor counterclockwise | 2
657 | Green light | 2
658 | Indicator light | 1
105 | Bearing | 8
123 | Gear | 4
125 | Main shaft | 4
415 | Blades | 4
421 | Battery | 1
422 | Protect part | 4
641 | Upper canopy | 1
642 | Battery cover | 1
643 | Lower canopy | 1
644 | Landing skid | 2
645 | Lamp cover | 4
646 | Back lamp cover | 1
649 | PCB | 1
650 | Red light | 2
651 | Motor clockwise | 2
652 | Motor counterclockwise | 2
657 | Green light | 2
658 | Indicator light | 1
1. Camera
2. Bubble
3. Fountain
4. Bullet
5. Rescue
3. Then connect the plug to the matching slot provided for that
purpose on the support base.
1. CAMERA = camera
2-3. SPRAYER = fountain or bubble blower
4. MISSILE = missile shooter
5. HOIST = Rescue module
FPV
Steps to install the FPV set on your copter:
WIFI
Application
1. Take picture (saved to camera roll)
2. Make video (saved to camera roll)
3. Go to media library
4. Adjust assertiveness (30/60/100%)
5. Steer by gyroscope
6. Eneble/disable steering on phone
7. Rotate image
8. Throttle/rudder
9. Elevator/aileron
10. Rudder trim
11. Aileron trim
12. Elevator trim
Wltoys
Imported by: WLtoys.eu / DroneX BV
Bloemstraat 86HS 1016 LE Amsterdam | www.wltoys.eu |
info@wltoys.eu
WARNING:
Non-compliance with safety rules may cause damage, injury and / or dangerous situations.
Warranty
The use of the copter is entirely at your own responsibility and at your own risk. Since we have no control beyond this manual
when you use the remote control and the copter (both flying and maintenance), we are not responsible for any damages or costs
incurred by improper use.
This warranty covers manufacturing and material defects in the context of normal use. We take no responsibility for damage
caused indirectly.