Instruction Sheet
ENERPAC.
POWERFUL SOLUTIONS. GLOBAL FORCE.
P2282 .
40,000 PSI Hand Pump .
11651 Rev.B 09/10
Index:
English... sees 2
Frangals.. 020 : 35
Deutsch 8
Malian... ett
Espafol.. i244
Nederlands 1517
| Pycexo..» 18-20
Repair Parts Sheets for this product are available from the
) Enerpac web site at wwwenerpac.com, or fromm your nearest
Authorized Enerpac Service Center or Enarpac Sales fice.
4.0 IMPORTANT RECEIVING INSTRUCTIONS
Visually inspect all components for shipping damage. Shipping
damage is not covered by warranty I shipping dsmaga is found,
notify carer at once. The cartier responsible for all repair and
replacement costs resulting from damage in shipment,
SAFETY FIRST
2.0 SAFETY ISSUES
Feed all instuctions, warnings and cautions
PA BS) carers. Fotow ai sacty precautions to avoid
_ jersonal injury oF property‘cariago' aug system
‘operation, Enerpac cannot be responsible for damage of inky
resulting from ‘unsafe product use, lack of maintenance. or
incorrect product anc/or system operation. Contact Enerpac
nen in doubt as to the satety precautions and operations. Ifyou
have never been trahed on high-pressure hycraule, safety,
consult your distibution or service center for a fee Enerpac
Hyer stely course,
Fatlue to comply wit the folawing cautions and warnings could
cause equlament damage and personal Huy.
[ACAUTION isused to indicate corect operating or malntenance
procedures and practices to prevent damage t, or dostuction
+ Of equipment or other propery.
AWARNING incioates a potential danger that requires cowect
provedutes or practoes to aver personal lun.
[DANGER is only used when your ection or lack of action may
‘cause serious injury or even death.
WARNING: Wear proper personal protective gear when
‘operating hydraulic equipment.
WARNING: Stay clear of loads supported by
hhydraulies. A oyinder, when used as aload ling device,
should never be used as a load holding device. After the
load has been raised or lowered, it must alneys be blocked
mechanically
Zea WARNING: USE ONLY RIGID PIECES TO HOLD
LOADS. Caretlly select steel or wood blocks that are
‘capable of supporting the load, Never use @ hydrauic
cylinder asa shim or spacer in any iting or pressing application.
Sn
iQ Besse
yap pr
eee
seratpttskeleeatrareteter tn cast ot
pee eri Crogan endo he
“A Novo so eet av ta Nee pes ar
ZX, retin te psu ot to puro. Hoe eros
inayat neuen Gora adr tcl.
WARNING: The stom operating pressure must net
tneced the prssreaing of honostates earponert
inthe syetars Insal presi geugo nto ajar fo
tmonter operating pressure RiyouruPeane wo Whetishoering
inte ste
CAUTION: Avoid camaging ryraue nose. Avid
Shay bond end Kno hos eth Mya hosce
Usha bent inked Foss Wil car seco vetepesere
Sharp bends and kinks wil internally damage the hase leading 10
premature hose falure.
>, Donat tp avo Dosa nt
Qh Bsc tees ae
> roping pressure to a damaged hose may cause i
tent,
oA} morte ee me
Pedal dong ort
CAUTION: Keep nyeasieequbmant way rom
<< flames and heat Excessive heat sotonpackings
Eoukrmutng hasten rae eae
Posaper te rdplenpe bern etondeyyy
Coen ciate ate ance reer cae
Parole and Sma tenets open
IMPORTANT: Do not lift hydraulic equicment by thea
Se
oe
Bele lee tree el
ah LIFTING LOAD. Cylinders should be placed on a flat
ee
.
lide Site re
ene
Fg, IMPORTANT: Hydraulic equipment must only be serviced
by a qualified hycraulic technician. For repair service,
Contact the Authorized ENERPAC Service Center in your
area. To protect your warranty, use only ENERPAC ol.
ovat errr mpi
fh mS ROR NS ae
break causing personal injury and property eamace *
ee
3.0 INSTALLATION
WARNING: Install gauge in system. This pump does
ot have a rat valve 20 monitoring system pressure
is necessary.
9.1 Tube Connection
1, Close pump release valve by tuning clockwise. Use finger
pressure only.
2. Using 40,000 psi rated tube and tube fitings, insert end bf
tubing through hole in gland nut and secure with sleeve.
‘3. Position end of tubing in discharge port of pump end secure
‘with gland nut, Do not overtighten.
4.0 OPERATION
1, Release handle lock pin located under beam.
2, The pump may be operated as a vented of a non-ventad
pump. Turn the reservoir fll cap to the position desired.
CAUTION: Do not stand directly over the pump
handle. It fs possible for the pump hancle to "kick
back." Keep your body to the side of the pump and
away from the line of force of the handle.
3, Open pump release valve by turning counterclockwise one
turn, Operate the pump using ful strokes six or more times
‘86 necessary to purge ar from the pump circu.
4, Open pump fil cap and chock the ll evel. Fill (using
Enerpee oil only) to the indicator mark on the end cap. DO
NOT overfil,
NOTE: The P-2282 pump has a usable oll capacity of 60 cu. I.
5. Close release valve by turning clockwise,
NOTE: Releaso valve is designed to close with hand pressure
Coniy. Use of tools to close valve can result in damage to the valve
and/or valve seat.
6. The pump may be operated from horizontal of vertical
position. In the vertical position, the discharge port must be
down,
‘The P-2282's a two stage pump. The shift trom trsttosecond
stage is automatic when the system pressure reaches 200
Pl.
8, The P-2282 pump does NOT have an internal reli valve.
‘This necessitates the use of a gauge at al times,
NOTE: When desighing a system to use with the P-2282,
allow for oll comprassibilty In low pressure applications this is
‘negligible, but 28 preseure increases, oll wil compress at a rate
‘of approximately 1/2% per 1000 ps.
5.0 MAINTENANCE
‘To check oll evel in pump, open release valve to allow of in the
system to return to pump. Remove filcap. Add Enerpactydraulle
ol unt level with mark on rear cap. Do not overfl To function
properly all hand pumps require air in the reservokr if the ol level
Is too high the pump will not operate.
Ifthe pump is operated under dirty conditions, frequent changing
of the oll is recommended, Refill wth clean Enerpac cl,
Periodically lubricate the beam pin, cross pin, and piston head
WARNING: This pump is not equipped with a relief
valve. A gauge must be used with this pump at all
times. Do not exceed 40,000 psi [2800 bar).
‘Out Port
Pump Roloase Valve