Professional Documents
Culture Documents
SDS Loctite AA 324
SDS Loctite AA 324
Page 1 of 9
LOCTITE AA 324 STRUCTURAL ADHESIVE
MSDS-No. : 153503
known as (LOCTITE 324 SPEEDBONDER) V000.0
Date of issue: 29.06.2015
Supplier:
Henkel Australia Pty Ltd
135-141 Canterbury Road
Kilsyth, Victoria, 3137
Australia
GHS Classification:
Hazard pictogram:
Precautionary Statement(s):
Prevention: P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources.
No smoking.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash hands thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing should not be allowed out of the workplace.
P273 Avoid release to the environment.
P280 Wear protective gloves, eye protection, and face protection.
Risk phrases:
R36/37/38 Irritating to eyes, respiratory system and skin.
R43 May cause sensitisation by skin contact.
R52/53 Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Safety phrases:
S23 Do not breathe gas/fumes/vapour/spray.
S24/25 Avoid contact with skin and eyes.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S28 After contact with skin, wash immediately with plenty of water and soap.
S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S46 If swallowed, seek medical advice immediately and show this container or label.
S61 Avoid release to the environment. Refer to special instructions/Safety data sheets.
Signal word:
HAZARDOUS
MSDS-No.: 153503 Page 3 of 9
V000.0 LOCTITE AA 324 STRUCTURAL ADHESIVE
known as (LOCTITE 324 SPEEDBONDER)
Identity of ingredients:
Eyes: Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes.
Get immediate medical attention.
Decomposition products in case of Thermal decomposition can lead to release of irritating gases and vapors.
fire:: Carbon monoxide.
Carbon dioxide.
Oxides of nitrogen.
Hydrogen cyanide.
Amines.
Isocyanates.
Additional fire fighting advice: In case of fire, keep containers cool with water spray.
Collect contaminated fire fighting water separately. It must not enter drains.
MSDS-No.: 153503 Page 4 of 9
V000.0 LOCTITE AA 324 STRUCTURAL ADHESIVE
known as (LOCTITE 324 SPEEDBONDER)
Clean-up methods: For small spills wipe up with paper towel and place in container for disposal.
For large spills absorb onto inert absorbent material and place in sealed container for
disposal.
Dispose of contaminated material as waste according to Section 13.
Ingredient [Regulated substance] form of TWA (ppm) TWA Peak Limit. Peak Limit. STEL (ppm) STEL
exposure (mg/m3) (ppm) (mg/m3) (mg/m3)
ACRYLIC ACID 2 5.9 - - - -
79-10-7
Engineering controls: Provide adequate local exhaust ventilation to maintain worker exposure below exposure
limits.
Please note that in practice the working life of chemical resistant gloves may be
considerably reduced as a result of many influencing factors (e.g. temperature). Suitable
risk assessment should be carried out by the end user. If signs of wear and tear are noticed
then the gloves should be replaced.
Respiratory protection: If inhalation risk exists, wear a respirator or air supplied mask complying with the
requirements of AS/NZS 1715 and AS/NZS 1716.
Hazardous decomposition Thermal decomposition can lead to release of irritating gases and vapors.
products:
Carbon monoxide.
Carbon dioxide.
Oxides of nitrogen.
Hydrogen cyanide.
Amines.
Isocyanates.
Health Effects:
Ingestion: Ingestion can cause gastrointestinal irritation, nausea, vomiting and diarrhea.
Skin: Causes skin irritation.
Symptoms may include redness, edema, drying, defatting and cracking of the skin.
May cause allergic skin reaction.
Eyes: Causes serious eye damage.
Contact with the eyes may cause moderate to severe eye injury. Eye contact may result in corneal
injury. Symptoms may include discomfort or pain, excess blinking and tear production, with
marked redness and swelling of the conjunctiva.
Inhalation: This product is irritating to the respiratory system.
May cause irritation to nose and throat.
Acute toxicity:
Skin corrosion/irritation:
Toxicity:
Disposal for uncleaned package: After use, tubes, cartons and bottles containing residual product should be disposed of as
chemically contaminated waste in an authorised legal land fill site or incinerated.
Disposal must be made according to official regulations.
Dangerous Goods information: Not classified as Dangerous Goods according to the criteria of the
Australian Code for the Transport of Dangerous Goods by Road and
Rail (ADG Code).
Reason for issue: Reviewed SDS. Reissued with new date. involved chapters: 1 - 16
Disclaimer:
The percentage weight (% w/w) of ingredients is not to be taken as a specification
guaranteed by Henkel Australia Pty. Limited, but only as an approximate guide to the
content of hazardous ingredients in the material. The information contained herein does
not constitute a guarantee by Henkel Australia Pty. Limited concerning the properties of
the material. The information contained in the Safety Data Sheet is offered in good faith
and has been developed from what is believed to be accurate and reliable sources. The
information is offered without warranty, representation, inducement or licence and Henkel
Australia Pty. Limited assumes no legal responsibility for reliance upon same. Henkel
Australia Pty. Limited disclaims any liability for loss, injury or damage incurred in
connection with the use of the material or its associated Safety Data Sheet. This
information is not to be construed as a representation that the material is suitable for any
particular purpose or use except those conditions and warranties implied by either
Commonwealth or State statutes. Customers are encouraged to make their own enquiries
as to the material’s characteristics and, where appropriate, to conduct their own tests in the
specific context of the material’s intended use.