Professional Documents
Culture Documents
Sealed SKF Single Row Angular Contact Ball Bearings
Sealed SKF Single Row Angular Contact Ball Bearings
Sealed SKF single row angular contact ball Reduced cost of ownership Environmentally friendly
bearings have an attractive combination of Sealed SKF single row angular contact ball When compared to open bearings, sealed
design features such as low friction seals bearings are well suited for bearing arrange- SKF single row angular contact ball bearings
and the same load carrying capacity as open ments where, due to limited space or for cost can significantly reduce grease consumption.
variants – features that enable new design reasons, external seals are not practical. These bearings do not have a relubrication
solutions for many demanding applications. Their favourable design characteristics save feature, so all costs associated with re-
space axially, enabling more compact machine lubrication including the costs to purchase
designs. and dispose of used grease are eliminated.
Reduced need for More importantly, these bearings can reduce
maintenance the environmental impact that a machine
will have over course of its life cycle.
Sealed SKF single row angular contact ball
bearings are ready-to-use units that are
filled at the factory with the proper amount
of high quality grease, under clean
conditions.
The cleanliness in a bearing is essential
for long service life. Protection is particularly
important during installation. By using
sealed single row angular contact ball bear-
ings instead of open bearings, solid contam-
inants are less likely to enter the bearing.
2
ball bearings provide distinct benefits
0
Standard Competitor
SKF RZ seal contact seal
Standard SKF bearings with non-contact seals were tested against standard competitor bearings with
contact seals on vertical shafts
3
Temperature measurements taken on the Fig. 1
outer rings showed that peak temperatures Temperature range for
for standard sealed SKF single row angular RZ seals
contact ball bearings were more than 30%
lower than competitor single row angular The permissible operating temperature
contact ball bearings with contact seals and range for RZ seals is –40 to +100 °C
that steady state temperatures were nearly (–40 to +212 °F). Temperatures up to
20% lower. 120 °C (248 °F) can be tolerated for brief
The design of the seal lip makes these periods.
bearings suitable for vertical shaft applica-
tions († diagram 2, page 3).
The mass of ejected grease is lower at Grease service life
sealed SKF single row angular contact ball Reducing the heat generated by a bearing
bearings with a non-contact seal. has a significant impact on grease service life.
Sealed SKF single row angular contact As a rule of thumb, reducing the operating
ball bearings with a non-contact seal on temperature by 15 °C doubles the service
both sides are identified by the designation life of the grease. However, other factors
suffix 2RZ. that increase or decrease service life must
In case of severe contamination or sealing be taken into consideration and include load,
against liquids is required, a low friction speed and misalignment. Please contact
contacting seal solution can be proposed. SKF application engineering to confirm the
Please contact SKF. expected grease service life.
Table 1
Technical specifications of SKF GXN grease for sealed single row angular contact ball bearings
Grease Temperature range [°C] Thickener Base NLGI Base oil viscosity [mm2/s]
oil type consistency at 40 °C at 100 °C
class (105 °F) (210 °F)
–50 0 50 100 150 200 250 °C
GXN1) Polyurea soap (di-urea) Mineral oil 2–3 96 10,5
4
Product data
Seals Load carrying capacity Lubricant
Bearings are fitted on both sides with a seal Sealed SKF single row angular contact ball Sealed SKF single row angular contact ball
made of an oil and wear-resistant NBR that bearings have the same load carrying capacity bearings are standard filled with a high
is reinforced with a sheet steel insert. and speed ratings as open SKF single row performance polyurea grease (GXN). Non-
angular contact ball bearings, see table 2. standard greases and grease-fills are avail-
able on request.
Cages For grease specifications see table 1.
Bearings are fitted with an injection moulded, Clearance and preload
ball centred cage made of a glass fibre rein- Standard sealed SKF single row angular
forced polyamide. contact ball bearings are supplied as non- Assortment
matchable bearings for single use. Univer- The range of standard sealed SKF single row
sally matchable bearings with three different angular contact ball bearings covers shaft
Dimensions and tolerances clearance and preload classes are available diameters 15 to 55 mm for the 72 series
Sealed SKF single row angular contact ball on request. and 12 to 50 mm for the 73 series.
bearings are dimensionally interchangeable
with same size SKF open bearings and are
manufactured with the same tolerances.
Table 2
mm mm mm kN kN r/min r/min –
5
Application recommendations
Typical examples
• Fluid machinery:
– Pumps
– Scroll compressors
• Material handling: Sicor elevator gearbox
– Elevators
• Gearboxes
• Electric motors
Typical requirements
• Minimum maintenance
• Reduced cost of ownership
• High degree of reliability
• Environmentally friendly
Main advantages:
• Replaces external sealing solutions
• Eliminates the need to grind seal coun-
terfaces for external seals
• Space saving compared to external seals
• Greased for life
• Protects against solid contaminants
• Reduced cost of ownership
Electric motor
6
Application example:
vertical shaft industrial pumps
For industrial pumps, reliability, long service made it possible to maintain a class A energy
life and energy efficiency are essential. efficiency rating.
To attain these performance requirements, Sealed SKF single row angular contact
leading pump manufacturers that used ball bearings have been used successfully in
competitor single row angular contact ball vertical shaft applications. This was made
bearings with contact seals in the past, possible by the design of the seals, combined
turned to SKF and tested non-contact RZ with the grease used.
seals with success. The switch to sealed SKF For additional information and support
single row angular contact ball bearings please contact the SKF application engi-
neering service.
7
The Power of Knowledge Engineering These competence areas include bearings and
Combining products, people, and application- units, seals, lubrication systems, mechatronics,
Bearings and Lubrication
Seals
housings systems
specific knowledge, SKF delivers innovative and a wide range of services, from 3-D computer
solutions to equipment manufacturers and pro- modelling to cloud-based condition monitoring
duction facilities in every major industry world- and asset management services.
wide. Having expertise in multiple competence SKF’s global footprint provides SKF customers
Mechatronics Services
areas supports SKF Life Cycle Management, a with uniform quality standards and worldwide
proven approach to improving equipment reliabil- product availability. Our local presence provides
ity, optimizing operational and energy efficiency direct access to the experience, knowledge and
and reducing total cost of ownership. ingenuity of SKF people.
skf.com