Professional Documents
Culture Documents
Ford We 910 - 2001 PDF
Ford We 910 - 2001 PDF
Ford We 910 - 2001 PDF
1. SCOPE
This standard gives the general and dimensional requirements for hexagon (M4 - M24), flanged
hexagon (M5 - M20), and hexagon thin nuts (M4 - M24).
NOTE: The dimensions specified in Table 1 are not suitable for property classes 9 and 12. The
requirements for Nut and Washer Assemblies are specified in WE 901.
2. REFERENCES
ISO 261 - General purpose metric screw threads - General plan.
ISO 965 - General purpose metric screw threads - Tolerances.
ISO 1502 - General purpose metric screw threads - Gauging.
ISO 1302 - Technical drawings - method of indicating surface roughness.
ISO 4288 - Rules and procedures for the measurement of surface roughness parameters using
stylus instruments.
WE 901 - General requirements for nut and washer assemblies.
WX 100 - Finish Specification
3. GENERAL REQUIREMENTS
Dimensions in mm
Thread Size d M4 M5 M6 M8 M10 M12 M14 M16 M20 M24
Pitch 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5 3
da max. 4.6 5.75 6.75 8.75 10.8 13 15.1 17.3 21.6 25.9
min. 4 5 6 8 10 12 14 16 20 24
dw min. 5.9 6.9 8.9 11.6 13.6 16.6 19.6 22.5 27.7 33.3
e min. 7.66 8.79 11.05 14.38 16.64 20.03 23.35 26.75 32.95 39.55
m max. 3.2 4.7 5.2 6.8 8.4 10.8 12.8 14.8 18 21.5
min. 2.9 4.4 4.9 6.44 8.04 10.37 12.1 14.1 16.9 20.2
1)
m' min. 2.32 3.52 3.92 5.15 6.43 8.3 9.68 11.28 13.52 16.16
s max. 7 8 10 13 15 18 21 24 30 36
min. 6.78 7.78 9.78 12.73 14.73 17.73 20.67 23.67 29.16 35
Dimensions in mm
Thread Size M4 M5 M6 M8 M10 M12 M14 M16 M20
Pitch 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5
c min. 0.9 1 1.1 1.2 1.5 1.8 2.1 2.4 3
da max. 4.6 5.75 6.75 8.75 10.8 13 15.1 17.3 21.6
min. 4 5 6 8 10 12 14 16 20
dc max. 10 11.8 14.2 17.9 21.8 26 29.9 34.5 42.8
dw min. 5.9 9.8 12.2 15.8 19.6 23.8 27.6 31.9 39.9
e min. 7.66 8.79 11.05 14.38 16.64 20.03 23.36 26.75 32.95
m max. 4 5 6 8 10 12 14 16 20
min. 3.7 4.7 5.7 7.6 9.6 11.6 13.3 15.3 18.9
s max. 7 8 10 13 15 18 21 24 30
min. 6.78 7.78 9.78 12.73 14.73 17.73 20.67 23.67 29.16
1)
m' min 2 2.2 3.1 4.5 5.5 6.7 7.8 9 11.1
2)
r max. 0.24 0.3 0.36 0.48 0.6 0.72 0.88 0.96 1.2
Dimensions in mm
Thread Size M4 M5 M6 M8 M10 M12 M14 M16 M20 M24
Pitch 0.7 0.8 1 1.25 1.5 1.75 2 2 2.5 3
da max. 4.6 5.75 6.75 8.75 10.8 13 15.1 17.3 21.6 25.9
min. 4 5 6 8 10 12 14 16 20 24
dw min. 5.9 6.9 8.9 11.6 13.6 16.6 19.6 22.5 27.7 33.2
e min. 7.66 8.79 11.05 14.38 16.64 20.03 23.35 26.75 32.95 39.55
m max. 2.2 2.7 3.2 4 5 6 7 8 10 12
min. 1.95 2.45 2.9 3.7 4.7 5.7 6.42 7.42 9.1 10.9
1)
m' min. 1.56 1.96 2.32 2.96 3.78 4.56 5.14 5.94 7.38 8.72
s max. 7 8 10 13 15 18 21 24 30 36
min. 6.78 7.78 9.78 12.73 14.73 17.73 20.67 23.67 29.16 35
Dimensions in mm
Nominal M4 M5 M6 M8 M10 M12 M14 M16 M20 M24
Thread
Diameter d
Concentricity - 0.44 0.54 0.66 0.78
Hexagon Flats
to Thread
Concentricity - - 0.86 1.04 1.24 -
Flanged
Portion to
Thread