Professional Documents
Culture Documents
LG 42LB5500 Chassis LA49B
LG 42LB5500 Chassis LA49B
LED TV
SERVICE MANUAL
CHASSIS : LA49B
CONTENTS . ............................................................................................. 2
SPECIFICATION........................................................................................ 4
ADJUSTMENT INSTRUCTION................................................................. 9
TROUBLE SHOOTING............................................................................. 16
BLOCK DIAGRAM................................................................................... 22
Copyright © LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
Copyright © LG Electronics. Inc. All rights reserved. -3- LGE Internal Use Only
Only for training and service purposes
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder ES
on page 3 of this publication, always follow the safety precautions. devices.
Remember: Safety First. 4. Use only an anti-static type solder removal device. Some solder
removal devices not classified as “anti-static” can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board mod- 6. Do not remove a replacement ES device from its protective
ule or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug or (Most replacement ES devices are packaged with leads electri-
other electrical connection. cally shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective material
installation of electrolytic capacitors may result in an explo- to the chassis or circuit assembly into which the device will be
sion hazard. installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or circuit,
high voltage meter or other voltage measuring device (DVM, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropriate
(by volume) isopropyl alcohol (90 % - 99 % strength) tip size and shape that will maintain tip temperature within the
CAUTION: This is a flammable mixture. range or 500 °F to 600 °F.
Unless specified otherwise in this service manual, lubrication of 2. Use an appropriate gauge of RMA resin-core solder composed
contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks are Do not use freon-propelled spray-on cleaners.
correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 °F to 600 °F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 °F to 600 °F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand against
ily by static electricity. Such components commonly are called the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor “chip” components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharging
wrist strap device, which should be removed to prevent poten-
tial shock reasons prior to applying power to the unit under test.
Copyright © LG Electronics. Inc. All rights reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed whenever
gently prying up on the lead with the soldering iron tip as the this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remaining good copper pattern. Solder the overlapped area and clip off
on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the lead
of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and if
necessary, apply additional solder.
Copyright © LG Electronics. Inc. All rights reserved. -5- LGE Internal Use Only
Only for training and service purposes
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
4. General Specification
No Item Specification Result Remark
1. Receiving System 1) ATSC / NTSC-M / 64 QAM / 256 QAM
2. Available Channel 1) VHF : 02~13
2) UHF : 14~69
3) DTV : 02-69
4) CATV : 01~135
5) CADTV : 01~135
3. Input Voltage AC 110V, 60HZ Mark : 110V, 60Hz (N.America)
4. Market NORTH AMERICA
5. Screen Size 32/42 inch Wide (1920 × 1080) FHD + 60Hz 32LB5600-UZ
39LB5600-UZ
42LB5500-UZ
42LB5600-UZ
49LB5500-UZ
55LB5500-UZ
32 inch Wide (1366 × 768) HD + 60Hz 32LB550B-UZ
32LB560B-UZ
6. Aspect Ratio 16:9
7. Tuning System FS
Copyright © LG Electronics. Inc. All rights reserved. -6- LGE Internal Use Only
Only for training and service purposes
No Item Specification Result Remark
8. Module DIRECT L LC320DUE-FGA3 LGD 32LB5600-UZ
DIRECT L LC320DXE-FGA3 LGD 32LB560B-UZ
DIRECT L LC320DXE-FGA5 LGD 32LB550B-UZ
DIRECT L NC320DXN-VSBP1 Sharp 32LB560B-UZ
DIRECT L NC320DXN-VSBP3 Sharp 32LB550B-UZ
DIRECT L NC390DUN-VXBP1 INX 39LB5600-UZ
DIRECT L LC420DUE-FGA3 LGD 42LB5600-UZ
DIRECT L LC420DUE-FGA5 LGD 42LB5500-UZ
DIRECT L T420HVF07.1 AUO 42LB5600-UZ
DIRECT L LC490DUE-FGA5 LGD 49LB5500-UZ
DIRECT L LC550DUE-FGA5 LGD 55LB5500-UZ
DIRECT L HC550DUN-ABHR1 BOE 55LB5500-UZ
9. Operating Environment 1) Temp : 0 ~ 40 deg
2) Humidity : ~ 80 %
10. Storage Environment 1) Temp : -20 ~ 60 deg
2) Humidity : ~ 85 %
Copyright © LG Electronics. Inc. All rights reserved. -7- LGE Internal Use Only
Only for training and service purposes
5.2. HDMI Input (DTV/PC)
Copyright © LG Electronics. Inc. All rights reserved. -8- LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTION
1. Application 4. MAIN PCBA Adjustments
This spec. sheet applies to LA49B Chassis applied LED TV all
models manufactured in TV factory * Download
(1) Execute ISP program “Mstar ISP Utility” and then click
“Config” tab.
(2) Set as below, and then click “Auto Detect” and check “OK”
2. Specification message
(1) Because this is not a hot chassis, it is not necessary to use If display “Error”, Check connect computer, jig, and set.
an isolation transformer. However, the use of isolation (3) Click “Connect” tab. If display “Can’t ”, Check connect
transformer will help protect test instrument. computer, jig, and set.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of
25 ±5 ºC of temperature and 65±10% of relative humidity if (1) (3)
there is no specific designation
(4) The input voltage of the receiver must keep 100~240V,
50/60Hz
(5) At first Worker must turn on the SET by using Power Only
key.
(6) The receiver must be operated for about 5 minutes prior to (2) OK
the adjustment when module is in the circumstance of over
15 ºC
In case of keeping module is in the circumstance of 0°C, it
should be placed in the circumstance of above 15°C for 2
hours
Please Check the Speed :
In case of keeping module is in the circumstance of below To use speed between from 200KHz to 400KHz
-20°C, it should be placed in the circumstance of above
15°C for 3 hours. (4) Click “Read” tab, and then load download file(XXXX.bin) by
clicking “Read”
※ Caution
When still image is displayed for a period of 20 minutes or
longer (especially where W/B scale is strong. (4)
Digital pattern 13ch and/or Cross hatch pattern 09ch), there
can some afterimage in the black level area
filexxx.bin
3. Adjustment items
3.1. Main PCBA Adjustments
(1) ADC adjustment : ADC adjustment is OTP (Auto ADC)
(2) EDID download : HDMI
Copyright © LG Electronics. Inc. All rights reserved. -9- LGE Internal Use Only
Only for training and service purposes
4.1. ADC Adjustment 4.2.5. EDID DATA
4.1.1. Overview 4.2.5.1. North America (PCM)
▪ ADC adjustment is needed to find the optimum black level 4.2.5.1.1. FHD Model
and gain in Analog-to-Digital device and to compensate RGB
deviation. ■ HDMI 1-FHD-8BIT (C/S : E708)
▪ ADC adjustment is OTP (Auto ADC) EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
4.2. EDID Download -----------------------------------------------------------------------------
4.2.1. Overview 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
▪ I t is a VESA regulation. A PC or a MNT will display an 10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
optimal resolution through information sharing without any 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
necessity of user input. It is a realization of “Plug and Play”. 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30
4.2.2. Equipment 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
(1) Since EDID data is embedded, EDID download JIG, HDMI 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
cable is not need. 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E7
(2) Adjust by using remote controller
EDID Block 1, Bytes 128-255 [80H-FFH]
4.2.3. Download method (using DFT)
※ PC(for communication through RS-232C), UART baud rate: 0 1 2 3 4 5 6 7 8 9 A B C D E F
115200 bps -----------------------------------------------------------------------------
Command : aa 00 00 (Start Factory mode) 0 | 02 03 19 F1 48 90 22 20 05 04 03 02 01 23 09 57
Command : ae 00 10 (Download All EDID) 10 | 07 67 03 0C 00 10 00 80 1E 02 3A 80 18 71 38 2D
Command : aa 00 90 (End of Factory mode) 20 | 40 58 2C 04 05 40 84 63 00 00 1E 01 1D 80 18 71
30 | 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 01 1D 00
40 | 72 51 D0 1E 20 6E 28 55 00 40 84 63 00 00 1E 8C
4.2.4. Download method (using Service Remocon)
50 | 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84 63 00 00
(1) Press Adj. key on the Adj. R/C.
60 | 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
(2) Select EDID D/L menu.
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08
(3) By pressing Enter key, EDID download will begin
(4) If Download is successful, OK is display, but If Download is
■ HDMI 2-FHD-8BIT (C/S : E7F8)
failure, NG is displayed.
EDID Block 0, Bytes 0-127 [00H-7FH]
(5) If Download is failure, Re-try downloads.
※Caution : W hen EDID Download, must remove HDMI
0 1 2 3 4 5 6 7 8 9 A B C D E F
Cable.
-----------------------------------------------------------------------------
(6) EDID Write confirmation
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
EDID D/L (PCM) 10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
HDMI1 : OK 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
HDMI2 : OK 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30
50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
4.2.5. Models for EDID Data 70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E7
2D
HD / 8bit FHD / 8bit EDID Block 1, Bytes 128-255 [80H-FFH]
HDMI 2ea HDMI 2ea
0 1 2 3 4 5 6 7 8 9 A B C D E F
North 32LB550B-UZ 32LB5600-UZ -----------------------------------------------------------------------------
America 32LB560B-UZ 39LB5600-UZ
0 | 02 03 19 F1 48 90 22 20 05 04 03 02 01 23 09 57
(PCM) 42LB5500-UZ
10 | 07 67 03 0C 00 20 00 80 1E 02 3A 80 18 71 38 2D
42LB5600-UZ
49LB5500-UZ
20 | 40 58 2C 04 05 40 84 63 00 00 1E 01 1D 80 18 71
55LB5500-UZ 30 | 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 01 1D 00
40 | 72 51 D0 1E 20 6E 28 55 00 40 84 63 00 00 1E 8C
50 | 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84 63 00 00
60 | 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F8
Copyright © LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
4.2.5.1.2. HD Model 4.2.5.2. AC3 EDID Data
4.2.5.2.1. FHD Model
■ HDMI 1-HD (C/S : 6F08)
EDID Block 0, Bytes 0-127 [00H-7FH] ■ HDMI 1-FHD-8BIT (C/S : E796)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
----------------------------------------------------------------------------- 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 -----------------------------------------------------------------------------
10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01 10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
40 | 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
50 | 18 88 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30
60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 6F 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E7
EDID Block 1, Bytes 128-255 [80H-FFH]
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
----------------------------------------------------------------------------- 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 | 02 03 19 F1 48 10 22 20 05 84 03 02 01 23 09 57 -----------------------------------------------------------------------------
10 | 07 67 03 0C 00 10 00 80 1E 02 3A 80 18 71 38 2D 0 | 02 03 1C F1 48 90 22 20 05 04 03 02 01 26 15 07
20 | 40 58 2C 04 05 40 84 63 00 00 1E 01 1D 80 18 71 10 | 50 09 57 07 67 03 0C 00 10 00 80 1E 02 3A 80 18
30 | 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 01 1D 00 20 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D
40 | 72 51 D0 1E 20 6E 28 55 00 40 84 63 00 00 1E 8C 30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E
50 | 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84 63 00 00 40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 00
60 | 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08 60 | 63 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 96
■ HDMI 2-HD (C/S : 6FF8)
EDID Block 0, Bytes 0-127 [00H-7FH] ■ HDMI 2-FHD-8BIT (C/S : E786)
EDID Block 0, Bytes 0-127 [00H-7FH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
----------------------------------------------------------------------------- 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 -----------------------------------------------------------------------------
10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01
20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01 10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70 20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80
40 | 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30 30 | 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C
50 | 18 88 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A 40 | 45 00 40 84 63 00 00 1E 66 21 50 B0 51 00 1B 30
60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC 50 | 40 70 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 6F 60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 E7
EDID Block 1, Bytes 128-255 [80H-FFH]
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
----------------------------------------------------------------------------- 0 1 2 3 4 5 6 7 8 9 A B C D E F
0 | 02 03 19 F1 48 10 22 20 05 84 03 02 01 23 09 57 -----------------------------------------------------------------------------
10 | 07 67 03 0C 00 20 00 80 1E 02 3A 80 18 71 38 2D 0 | 02 03 1C F1 48 90 22 20 05 04 03 02 01 26 15 07
20 | 40 58 2C 04 05 40 84 63 00 00 1E 01 1D 80 18 71 10 | 50 09 57 07 67 03 0C 00 20 00 80 1E 02 3A 80 18
30 | 1C 16 20 58 2C 25 00 40 84 63 00 00 9E 01 1D 00 20 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D
40 | 72 51 D0 1E 20 6E 28 55 00 40 84 63 00 00 1E 8C 30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E
50 | 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84 63 00 00 40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 00
60 | 18 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F8 60 | 63 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 86
Copyright © LG Electronics. Inc. All rights reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
4.2.5.2.2. HD Model 5. Final Assembly Adjustment
■ HDMI 1-HD (C/S : 6F96) 5.1. White Balance Adjustment
EDID Block 0, Bytes 0-127 [00H-7FH] 5.1.1. Overview
5.1.1.1. W/B adj. Objective & How-it-works
0 1 2 3 4 5 6 7 8 9 A B C D E F (1) Objective: To reduce each Panel’s W/B deviation
----------------------------------------------------------------------------- (2) How-it-works: When R/G/B gain in the OSD is at 192, it
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 means the panel is at its Full Dynamic Range. In order to
10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 prevent saturation of Full Dynamic range and data, one of
20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01 R/G/B is fixed at 192, and the other two is lowered to find
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70 the desired value.
40 | 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30 (3) Adj. condition: normal temperature
50 | 18 88 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A - Surrounding Temperature: 25±5 ºC
60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC - Warm-up time: About 5 Min
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 6F - Surrounding Humidity: 20% ~ 80%
- Before White balance adjustment, Keep power on status,
EDID Block 1, Bytes 128-255 [80H-FFH] don’t power off
0 1 2 3 4 5 6 7 8 9 A B C D E F 5.1.2. Equipment
----------------------------------------------------------------------------- (1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:
0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 CH14)
10 | 01 18 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26 (2) A dj. Computer(During auto adj., RS-232C protocol is
20 | 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 01 01 needed)
30 | 01 01 01 01 01 01 66 21 50 B0 51 00 1B 30 40 70 (3) Adjust Remocon
40 | 36 00 40 84 63 00 00 1E 64 19 00 40 41 00 26 30 (4) V ideo Signal Generator MSPG-925F 720p/204-Gray
50 | 18 88 36 00 40 84 63 00 00 1E 00 00 00 FD 00 3A (Model:217, Pattern:49)
60 | 3E 1E 53 10 00 0A 20 20 20 20 20 20 00 00 00 FC → Only when internal pattern is not available
70 | 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 01 6F ※ C olor Analyzer Matrix should be calibrated using
CS-1000
EDID Block 1, Bytes 128-255 [80H-FFH]
0 1 2 3 4 5 6 7 8 9 A B C D E F
-----------------------------------------------------------------------------
0 | 02 03 1C F1 48 10 22 20 05 84 03 02 01 26 15 07
10 | 50 09 57 07 67 03 0C 00 20 00 80 1E 02 3A 80 18
20 | 71 38 2D 40 58 2C 04 05 40 84 63 00 00 1E 01 1D
30 | 80 18 71 1C 16 20 58 2C 25 00 40 84 63 00 00 9E
40 | 01 1D 00 72 51 D0 1E 20 6E 28 55 00 40 84 63 00
50 | 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E 96 00 40 84
60 | 63 00 00 18 00 00 00 00 00 00 00 00 00 00 00 00
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 86
Copyright © LG Electronics. Inc. All rights reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
5.1.3. Equipment connection 5.1.5. Adjustment method
5.1.5.1. Auto WB calibration
(1) Set TV in ADJ mode using P-ONLY key (or POWER ON
key)
(2) Place optical probe on the center of the display
- It need to check probe condition of zero calibration before
adjustment.
(3) Connect RS-232C Cable
(4) Select mode in ADJ Program and begin a adjustment.
(5) When WB adjustment is completed with OK message,
check adjustment status of pre-set mode (Cool, Medium,
Warm)
(6) Remove probe and RS-232C cable.
※ W/B Adj. must begin as start command “wb 00 00” , and
finish as end command “wb 00 ff”, and Adj. offset if need.
Copyright © LG Electronics. Inc. All rights reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
5.1.6. Reference 5.2. Option selection per country
( White Balance Adj. coordinate and color 5.2.1. Overview
temperature) (1) Tool option selection is only done for models in Non-USA
▪ Luminance: 204 Gray, 80IRE North America due to rating
**(normal line) Model : For LGD (LB56xx, LB55xx) (2) Applied model: LA32B Chassis applied to CANADA and
▪ S tandard color coordinate and temperature using MEXICO
CA-210(CH-14) – by aging time
Cool Medium Warm 5.2.2. Country Group selection
H/R Time(Min) x y x x y x (1) Press ADJ key on the Adj. R/C, and then select Country
Group Menu
271 270 286 289 313 329 (2) Depending on destination, select US, then on the lower
1 0-2 281 285 296 304 323 344 Country option, select US, CA, MX.
Selection is done using +, - KEY
2 3-5 280 284 295 303 322 343
(3) Using DFT(Auto)
3 6-9 279 282 294 301 321 341 ※ PC (for communication through RS-232C) -> UART Baud
4 10-19 277 279 292 288 319 338 rate : 115200 bps
Command : ah 00 00 DATA(Area Number(hexadecimal))
5 20-35 275 275 290 294 317 334
ITEM DATA(Area Number) AREA
6 36-49 273 273 288 292 315 332
7 50-79 272 272 287 291 314 331
AREA OPTION1 0 USA
**(aging chamber) Model : For LGD (LB56xx, LB55xx) 5.2.3. Tool Option inspection
▪ Standard color coordinate and temperature using ▪ Press Adj. key on the Adj. R/C, then select Tool option
CA-210(CH-14) – by aging time
Tool Tool Tool Tool
Model Module
Cool Medium Warm option1 option2 option3 option4
H/R Time(Min) x y x x y x 32LB550B-UZ LGD 784 13314 41036 20544
271 270 286 289 313 329 32LB560B-UZ SHARP 13074 9218 41036 20544
1 0-5 280 285 295 304 319 340 32LB550B-UZ SHARP 13074 13314 41036 20544
2 6-10 276 280 291 299 315 335 42LB5500-UZ LGD 1552 5126 41036 24640
3 11-20 272 275 287 294 311 330 42LB5500-UZ AUO 9744 5126 41036 24640
4 21-30 269 272 284 291 308 327 42LB5600-UZ LGD 1552 1030 41036 24640
5 31-40 267 268 282 287 306 323 42LB5600-UZ AUO 9744 1030 41036 24640
6 41-50 266 265 281 284 305 320 39LB5600-UZ INX 17682 1030 41036 24640
7 51-80 265 263 280 282 304 318 49LB5500-UZ LGD 2064 5126 41036 24640
8 81-119 264 261 279 280 303 316 55LB5500-UZ LGD 2576 5126 41036 24640
9 Over 120 264 260 279 279 303 315 55LB5500-UZ BOE 23058 5126 41036 24640
32LB550B-UZ BOE 21266 13314 41036 24640
**For INX,AUO,SHARP,CSOT Module.( In the case of , the color
temperature spec of cool mode is 13000K) 32LB5600-UZ LGD 784 1026 41036 24640
Copyright © LG Electronics. Inc. All rights reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
6. GND and HI-POT Test * USB S/W Download (option, Service only)
(1) Put the USB Stick to the USB socket.
6.1. GND & HI-POT auto-check preparation (2) Automatically detecting update file in USB Stick.
(1) Check the POWER CABLE and SIGNAL CABE insertion
- If your downloaded program version in USB Stick is Low,
condition
it didn't work. But your downloaded version is High, USB
data is automatically detecting
6.2. GND & HI-POT auto-check (3) Show the message "Copying files from memory"
(1) Pallet moves in the station. (POWER CORD / AV CORD is
tightly inserted)
(2) Connect the AV JACK Tester.
(3) Controller (GWS103-4) on.
(4) GND Test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, execute next process (Hi-pot test).
(Remove A/V CORD from A/V JACK BOX)
(5) HI-POT test (Auto)
- If Test is failed, Buzzer operates.
- If Test is passed, GOOD Lamp on and move to next
process automatically (4) Updating is staring.
6.3. Checkpoint
(1) Test voltage
- GND: 1.5KV/min at 100mA
- SIGNAL: 3KV/min at 100mA
(2) TEST time: 1 second
(3) TEST POINT
- GND Test = P OWER CORD GND and SIGNAL CABLE
GND.
- Hi-pot Test = POWER CORD GND and LIVE & NEUTRAL.
(4) LEAKAGE CURRENT: At 0.5mArms
7.2. Specification
No Item Min Typ Max Unit Remark
1 Audio practical 4.5 5.0 6.0 W (1) Measurement
max Output, L/R 6.0 6.3 6.9 Vrms condition
(Distortion=10% - EQ/AVL/Clear
max Output) Voice: Off (5) After updating is complete, The TV will restart automatically.
(2) Speaker (6) If TV turns on, check your updated version and Tool option.
(8Ω Impedance)
LB55 Series
(refer to the next page about tool option)
* If downloading version is higher than your TV have, TV
9.0 10.9 12.0 W (1) Measurement can lost all channel data. In this case, you have to
8.5 9.3 9.8 Vrms condition
- EQ/AVL/Clear channel recover. If all channel data is cleared, you didn't
Voice: Off have a DTV/ATV test on production line.
(2) Speaker
(8Ω Impedance)
※After downloading, TOOL OPTION setting is needed again.
LB56 Series
(1) Push "IN-START" key in service remote controller.
(2) Select "Tool Option 1" and Push “OK” button.
(3) Punch in the number. (Each model has their number.)
Copyright © LG Electronics. Inc. All rights reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
TROUBLE SHOOTING
1. Power-up boot check
Check stand-by Voltage. No ok M ain B/D 3.5V Line ok
Check 18pin Power connector Replace Power board.
P401 3, 5, 6pin : +3.5V_ST Short Check
ok
ok
ok
Check M ulti Voltage No
P401 9, 10pin : 24V Replace Power Board
/ 13, 14, 15pin:12V
ok
Check IC402/3/4 Output Voltage
IC402 : 2.5V No
IC403 : 1.5V Replace IC402, IC403, IC404, Q403
IC404 : 1.15V
Q403 : 3.3V
ok
Check LVDS Power Voltage No
Q409 : 12V Replace Q409
ok
No
Check M star LVDS Output Replace M star(IC101) or M ain Board
ok
ok
Change M odule
Copyright © LG Electronics. Inc. All rights reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
2. Digital/Analog TV Video
ok
No
Check Tuner 3.3V Power
Replace L3703
L3703
ok
ok
ok
No
Check Mstar LVDS Output Replace M star(IC101) or M ain Board.
3. AV Video
Check input signal format.
Is it supported?
ok
ok
ok
No
Check CVBS_DET Signal Replace R1713
ok
No
Check Mstar LVDS Output Replace M star(IC101) or M ain Board.
Copyright © LG Electronics. Inc. All rights reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
4. Component Video
Check input signal format.
Is it supported?
ok
ok
Check JK1701 No
Replace Jack
Y/PB/PR signal Line
ok
No
Check COMP_DET Signal Replace R1712 or R1713
ok
No
Check Mstar LVDS Output Replace M star(IC101) or M ain Board.
5. HDMI Video
Check input signal format.
Is it supported?
ok
ok
Check EDID No
R810, R811, R815, R816 I2C Signal Replace the defective IC or re-download EDID data
ok
No
Check JK800, JK801 Replace Jack
ok
No
Check HDMI_DET (HPD) Replace R808, R809, Q800, R803, R814
ok
ok
No
Check Mstar LVDS Output Replace M star(IC101) or M ain Board.
Copyright © LG Electronics. Inc. All rights reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
6. MHL Video
Check input signal format.
Is it supported?
ok
ok
No
Check MHL Signal (R214, R215) Replace the defective IC or re-download EDID data
ok
No
Check JK801 Replace Jack
ok
No
Check CD_Sense, Cbus, Vbus Replace R817, C800
ok
ok
No
Check Mstar LVDS Output Replace M star(IC101) or M ain Board.
Copyright © LG Electronics. Inc. All rights reserved. - 19 - LGE Internal Use Only
Only for training and service purposes
7. All Source Audio
Check the TV Speaker M enu Off
Toggle the Menu
(M enu -> Audio -> TV Speaker)
On
ok
No
Check Mstar AUDIO_MASTER_CLK Replace M star(IC101) or M ain Board.
R148
ok
ok
ok
ok
No Replace connector
Check Connector & P5600
if found to be damaged.
ok
Copyright © LG Electronics. Inc. All rights reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
8. Digital/Analog TV Audio
ok
No
Check Tuner 3.3V Power
Replace L3703
L3703
ok
ok
ok
Follow procedure
‘7. All source audio’
trouble shooting guide.
9. AV Audio
Check AV Cable for damage
for damage or open conductor
ok
ok
Follow procedure
‘7. All source audio’
trouble shooting guide.
ok
ok
Follow procedure
‘7. All source audio’
trouble shooting guide.
Copyright © LG Electronics. Inc. All rights reserved. - 21 - LGE Internal Use Only
Only for training and service purposes
Copyright ©
X-tal Serial Flash EEPROM
IF
(24MHz) 8M x 8bit 64K x 8bit
On board
Air/Cable
IF(ATSC)
DDR2
- 22 -
End DSP MCLK
TAS5733
UART
TMDS/DDC HDMI
HDMI
RX
540mV
USB2.0 USB
502
900
400
420
410
510
540
121
530
120
LV1
820
Set + Stand
A10
200
A2
Copyright © LG Electronics. Inc. All rights reserved. - 23 - LGE Internal Use Only
Only for training and service purposes
<SOC_RESET>
POWER_ON/OFF
/MHL_OCP_DET
SIDE_USB_DP
SIDE_USB_DM
MHL_OCP_EN
<MAIN SoC Vcc>
SOC_RESET
POWER_DET
/FLASH_WP
PANEL_CTL
AMP_RESET
MODEL_OPT
+3.5V_ST
PWM_DIM2
AMP_MUTE
USB1_CTL
USB1_OCD
AVDD_MOD
SPI_SCK
SPI_SDO
PWM_DIM
/SPI_CS
SPI_SDI
INV_CTL
AMP_SCL
AMP_SDA
I2C_SCL
I2C_SDA
PM_RXD
PM_TXD
OPT
RXBCK-
RXBCK+
RL_ON
RXB3+
RXB3-
RXB2+
RXB2-
RXB1+
RXB1-
RXB0+
RXB0-
R103
470
IR
POWER_DET_RESET L102 +3.5V_ST
PZ1608U121-2R0TF
+3.5V_ST AVDD_MOD
L105
PZ1608U121-2R0TF AVDD_DADC
+3.5V_ST
1K
1K
AR105
1/16W
T120
4.7K
C131 C132
OPT
C121 0.1uF 0.1uF C147
OPT 10uF C127 16V C139 0.1uF
R112
R115
16V
AR111
1/16W
C100 C101 6.3V 1uF 0.1uF C140 16V
4.7uF 4.7uF 10V 16V 0.1uF
L108
33
10V 10V 16V
PZ1608U121-2R0TF AVDD_AU33
<Chip config.> AR112
AR110
1/16W
SOC_RESET 4.7K
100
100
1/16W AR108
1/16W +1.15V_VDDC C146
0.1uF
Closed to SoC as possible 16V
R_ODD[5]/LVB1-/RLV3(CLK)-/EPI6-
R_ODD[4]/LVB1+/RLV3(CLK)+/EPI6+
R104 C103
470K 0.1uF R117 C130
16V Closed to SoC as possible 10K C138 L107
0.1uF
R_ODD[1]/LVBCLK-/RLV5-/EPI4-
R_ODD[0]/LVBCLK+/RLV5+/EPI4+
C120 0.1uF PZ1608U121-2R0TF AVDD_DMPLL
C126 C129 16V
1/16W
100
AR104
AR107 10uF 0.1uF 16V
1uF C137
LVSYNC/GPIO16/RLV0-/GPIO16
LHSYNC/GPIO17/RLV0+/GPIO17
R_ODD[7]/LVB0-/RLV2-/EPI7-
R_ODD[6]/LVB0+/RLV2+/EPI7+
R_ODD[3]/LVB2-/RLV4-/EPI5-
R_ODD[2]/LVB2+/RLV4+/EPI5+
G_ODD[7]/LVB3-/RLV6-/EPI3-
G_ODD[6]/LVB3+/RLV6+/EPI3+
G_ODD[5]/LVB4-/LLV0-/EPI2-
G_ODD[4]/LVB4+/LLV0+/EPI2+
33 6.3V 10V 16V 0.1uF
5V_DET_HDMI_1
HPD1
1/16W 16V C145
0.1uF
LDE/GPIO18/RLV1-/GPIO18
LCK/GPIO19/RLV1+/GPIO19
16V
INT/GPIO64/I2S_OUT_MCK
AR106
1/16W
L106
<HW_OPTION>
33
PZ1608U121-2R0TF AVDD_VIDEO
GPIO10/TCON10
R114
10K DDR_CMD DDR_DATA
PWM0/GPIO15
PWM1/GPIO14
GPIO0/TCON0
GPIO1/TCON1
GPIO2/TCON2
GPIO3/TCON3
GPIO4/TCON4
GPIO5/TCON5
GPIO6/TCON6
GPIO7/TCON7
GPIO8/TCON8
GPIO9/TCON9
+3.3V_NORMAL C144
+1.8V_DDR +1.8V_DDR 0.1uF
ARC/GPIO87
AVDD_MOD_3
L101 L104 16V
HOTPLUG_A
HOTPLUG_D
PZ1608U121-2R0TF PZ1608U121-2R0TF
DDCA_CK
DDCA_DA
SPI_CK
SPI_CZ
SPI_DI
SPI_DO
C119 C136
FHD C118 0.1uF OPT 0.1uF OPT
DP_P0
DM_P0
RESET
R102 10uF 16V C125 C135
10uF 16V C141
4.7K 6.3V
IRIN
TEST
0.1uF 6.3V 0.1uF
16V 16V
74 B_ODD[7]/LVA2-/LLV3(CLK)-
KEY1 SAR1/GPIO74 RXACK+
Closed to SoC as possible
129
KEY2
73 B_ODD[6]/LVA2+/LLV3(CLK)+
R111 1K SAR2/GPIO73 130
RXACK-
LED_RED
72 B_ODD[5]/LVACLK-/LLV4- RXA2+
VDDC_3 131
+1.15V_VDDC
71 B_ODD[4]/LVACLK+/LLV4+ RXA2-
VDDIO_DATA 132
DDR_DATA
70 B_ODD[3]/LVA3-/LLV5- RXA1+
R110 1K GPIO54 133
AV_DET
AR102 69 B_ODD[2]/LVA3+/LLV5+ RXA1-
100
1/16W DDCDD_CL 134
DDC_SCL_1
68 B_ODD[1]/LVA4-/LLV6- RXA0+
DDCDD_DA 135
DDC_SDA_1
67 B_ODD[0]/LVA4+/LLV6+ RXA0-
COMP_DET
R109 1K DDCDA_CL 136 GPIO53/I2S_OUT_SD
5V_DET_HDMI_2
R108 10K DDCDA_DA 137 IC102 66
65 GPIO52/I2S_OUT_BCK
AUD_LRCH
AUD_LRCK
DDC_SCL_2
DDCDB_CL 140 GPIO49/SPDIF_OUT
62 SPDIF
IC100-*1
NVRAM_ATMEL
HPD2
HOTPLUG_B 141 [M1L] 61 GPIO47
R126
100
SPDIF_OUT
AT24C512C-SSHD-T
AVDD_5V_MHL
AVDD_5V_MHL 142 VCOM_SDA
60 GPIO46/MHL_VBUS VCOM_SCL
A0 VCC GND_EFUSE 143
1 8
59 GPIO45/I2C_SCLM/UART_RX1
A1 WP
+1.15V_VDDC VDDC_4 144 TU_SCL
2 7
58 GPIO44/I2C_SDAM/UART_TX1
A2
3 6
SCL
CK-_HDMI1
RXCN_D 145 TU_SDA
57 VDDC_2 +1.15V_VDDC
GND
4 5
SDA
CK+_HDMI1
RXCP_D 146
56 VDDIO_CMD DDR_CMD
D0-_HDMI1
RX0N_D 147
55 AVDD_MOD_2 AVDD_MOD
D0+_HDMI1
RX0P_D 148
54 XOUT C143 15pF
D1-_HDMI1 RX1N_D 149 R127 X100
EEPROM(512KB) 53 XIN 1M 24MHz
C142 15pF
NVRAM_ROHM D1+_HDMI1 RX1P_D 150
IC100 52 AVDD3P3_DMPLL AVDD_DMPLL
BR24G512FJ-3 D2-_HDMI1
RX2N_D 151 Closed to SoC
+3.5V_ST 51 AVDD3P3_DADC AVDD_DADC
D2+_HDMI1
RX2P_D 152
A0
1 8
VCC 50 VIFM R122 0 C123
IF_N_MSTAR
THERMAL
CK-_HDMI2
RXCN_B 153 0.1uF
16V
C105
0.1uF 49 VIFP R123 0 C124
157
C102 C104
8pF 8pF
RX1N_B
RX1P_B
RX2N_B
RX2P_B
AVDD_MOD_1
RXCN_A
RXCP_A
RX0N_A
RX0P_A
RX1N_A
RX1P_A
RX2N_A
RX2P_A
HSYNC0
BIN0P
SOGIN0
GIN0P
GIN0M
RIN0P
VSYNC0
BIN1P
SOGIN1
GIN1P
GIN1M
RIN1P
VSYNC1
CVBS1
CVBS0
VCOM
CVBS_OUT1
VDDC_1
AVDD_AU33
AUR0
AUL0
AUR1
AUL1
AUR2
AUL2
AUR3
AUL3
VAG
VRM
LINEOUTL3
LINEOUTR3
LINEOUTL0
+3.3V_NORMAL
PZ1608U121-2R0TF
SERIAL FLASH(64MB) +3.5V_ST
L103
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
0.047uF
1000pF
2.2uF
2.2uF
SFLASH_MXIC SFLASH_WINBOND
25V
50V
25V
25V
25V
10V
10V
25V
25V
OPT IC101
IC101-*1
R105 MX25L6406EM2I-12G
4.7K W25Q64FVSSIG C122
C116 0.1uF
C107
C108
C109
C111
C112
C113
C114
C115
C110
33
68
0.1uF
33
6.3V 0.047uF
AR109
25V
R113
R118
R120
R121
R119
/FLASH_WP WP SCLK
3 6 SPI_SCK WP[IO2] CLK
3 6
L100
GND SI/SIO0
AVDD_MOD
D1+_HDMI2
D2-_HDMI2
D2+_HDMI2
4 5
AVDD_VIDEO
+1.15V_VDDC
AVDD_AU33
COMP_Pb+
DTV/MNT_VOUT
COMP_Pr+
COMP_Y+
COMP_R_IN
COMP_L_IN
COMP_Y+
Copyright ⓒ 2014 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
L14 K-TASK POWER BLOCK
PMV48XP
+3.5V_ST --> 3.375V --> 3.46V
PANEL_Vcc Power_DET
FET_12V_NXP
FROM LIPS or POWER B/D +12V --> 3.58V --> 3.82V (3.68V)
Q205-*1
D
+12V
SOC_RESET_+3.5V
PANEL_VCC
G
R235-*1
+12V +3.5V_ST 100
L203 FET_12V_DIODES
Q205 +3.5V_ST
UBW2012-121F R234
RL_ON_Buffer DMP2130L 100K
+3.5V_ST
MMBT3906(NXP)
D
Q200 OPT R236
OPT C210 R230 R233 RESET_IC_DIODES
R215 OPT 0 4.7K
C208 10uF 2.7K
3 10K 16V G R219 R223 1% IC204
1 OPT 0.1uF APX803D29 SOC_RESET_PD_IC
3.3K 3.3K
R207 25V R235
R200 33K Vgs=8.15V POWER_DET
RL_ON_Buffer 2 VCC RESET 300
10K 3 2
R202
RL_ON 10K R214 1
4.7K
C222 R229 GND C232
1.2K 0.1uF
R201 0.1uF
10K C 16V 1%
RL_ON_Direct
RL_ON_Direct PANEL_CTL B Q203 POWER_DET_RESET
R203 MMBT3904(NXP)
ICVS0518150FR_
0 +3.3V_NORMAL
E CI_RESET_IC_ROHM
+3.5V_ST IC204-*1
R208 R209
VA201
OPT
100 1K BD48K28G
P200 C R211
SMAW200-H18S5 R210 10K VDD VOUT
+3.5V_ST B 10K INV_CTL 3 2
1
C200 C202
ZD200
10uF
5.5V
PWR ON DRV ON
5V
PMV48XP
+24V 24V 9 10 24V
PWM_DIM2
+3.3V_Normal
FET_3.3V_NXP
OPT GND 11 12 GND
C205 C206
12V 12V
Q204-*1
4.7uF 0.1uF 13 14
50V 50V 12V 15 16 NC
D
GND 17 18 GND
L200 +3.5V_ST
MLB-201209-0120P-N2 FET_3.3V_DIODES +3.3V_NORMAL
+12V
OPT Q204
G
L204
C203 C204 19 DMP2130L PZ1608U121-2R0TF
4.7uF 0.1uF
D
.
16V 16V
OPT
C211 C214 ZD202
+1.15V_VDDC
G
C209 0.1uF 10uF 5V
R217 4.7uF 16V
12K 6.3V
10V +3.5V_ST
THERMAL
R216 16V 6.3V 10V 16V
1.8K C237
+1.15V_VDDC VIN EN
9
2 7
1000pF
L207 C231 50V
R212 C 3.6uH 0.1uF PH COMP
POWER_ON/OFF 16V 3 6
10K B Q202
MMBT3904(NXP)
OPT
3A R237
C236
0.33uF
OPT 16V
C220 C224 C225 GND VSENSE 2.7K
E ZD203 22uF 22uF 4 5 1%
0.1uF
C228
270pF
R232
20K
1% R1
C233
0.039uF
50V
C235
390pF
50V
50V
+3.3V_NORMAL
R231 R2
+1.8V_DDR 47K
IC200 1%
AZ1117EH-ADJTRG1
IN OUT
C201
R1 Vout=0.808*(1+R1/R2)
ADJ/GND 1% R206
10uF 1
6.3V R204 ZD201
2.7K 2.5V
C207
10uF
6.3V
R2 1%
R205
1.2K
+5V_USB & MHL W/ OCP CI_GateIC_Toshiba
IC202-*1
TC7SZ08FU_TOSHIBA
+12V
IN_B VCC
1 5
Vout=1.25*(1+R2/R1)
IN_A
2
C215 C216
10uF 10uF
16V 16V GND OUT_Y
3 4
Vout=0.8*(1+R1/R2)
[EP]GND
PGND_2
PGND_1
PGOOD
VIN_2
VIN_1
R222
OPT 100K
V7V
C212
100pF +5V_NORMAL
50V C218 L205
24
23
22
21
20
19
0.047uF 4.7uH
EN BST 25V
C213 1 18
R220 4700pF
4.7K 50V THERMAL C227
+3.3V_NORMAL COMP
25
LX_2 R1 +3.3V_NORMAL
2 17 C223 22uF GateIC_STC
R228 16V
OPT SS LX_1 18K 82pF IC202
R221 3 16 1% 50V
OPT 74LVC1G08GW
0 ROSC FB
R218 IC201
4.7K 4 15
EN_SW2 TPS65282REGR SW_IN_2 R2
MHL_5V_EN 5 14 B VCC
1 5
USB1_CTL
EN_SW1
6
4A 13
SW_IN_1
R227
3.3K
1%
MHL_CD_SENSE
10
11
12
A
C219
7
+3.3V_NORMAL 2
10uF MHL_OCP_EN
+5V_USB 16V
FAULT2
FAULT1
SW_OUT2
RLIM
AGND
SW_OUT1
GND Y
3 4
MHL_5V_EN
AR200
1/16W
10K
D200 R226
MBR230LSFT1G 10
OPT 30V
R225 C217
100K 10uF
/MHL_OCP_DET
USB1_OCD
10V
16K(1.6A)->14K(1.8A)
Copyright ⓒ 2014 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
AUDIO AMP(TI)/LVDS/IR IR
+3.5V_ST
AR303
1/16W
10K
HD
P301 KEY1
10031HR-30
FHD OPT
C338 IR_10PIN
P300 VR302 0.1uF IR_8PIN
FI-RE51S-HF-J-R1500 16V P302 P303
1
12507WR-08L 12507WR-10L
1
2
V-COM I2C
3 VCOM_SCL_M KEY2 1 1
2 OPT
4 VCOM_SDA_M +3.3V_NORMAL OPT
LVDS_SEL C337
3 VR301 0.1uF
5 2 2
16V
4 +3.3V_NORMAL
VCOM_SDA_M 6 RXA0-
5 VCOM_SCL_M +3.5V_ST 3 3
7 RXA0+ V_COM V_COM
OPT L307
6 R302 R316 R317 PZ1608U121-2R0TF
3.3K 8 2K 2K
4 4
7
9 AR302
RXA1- 0
OPT C335 C336
8 1/16W 0.1uF 1000pF
R301 10 16V 50V 5 5
RXA1+
9 10K VCOM_SCL_M VCOM_SCL
11
VCOM_SDA_M VCOM_SDA
10 LED_RED 6 6
12 RXA2- V_COM
11 OPT
13 VR300 +3.5V_ST
RXA2+ 7 7
12
RXA0- 14
OPT
13 R322
RXA0+ 15 8 8
RXACK- 3.3K
14
RXA1- 16 RXACK+ IR 9
15 9
RXA1+ 17 C339
100pF OPT
16 LVDS_SEL 50V VR303
RXA2- 18 RXA3- 10
17 +3.3V_NORMAL
RXA2+ 19 RXA3+
18 11
20
19 OPT
RXACK- 21 R307
3.3K
20
RXACK+ 22
21 PANEL_VCC
23 OPT
R306
22 10K
RXA3- 24 HD
23 L302
RXA3+ 25 120OHM
24 UBW2012-121F
26
25
FHD 27
R300
26
28 OPT HD
0
27 C303 C306
29 10uF 0.1uF
28 16V 16V
RXB0- 30
29
RXB0+
31
30
RXB1-
31
RXB1+
32
RXB2-
33
RXB2+
34
35
RXBCK-
36
RXBCK+
37
38
RXB3-
39
RXB3+
40
41
AR300
0
AUDIO AMP(TI)
1/16W FHD
42
1/16W
C300 C301
Separate DGND AND AVSS 10.0uH
R321
10uF 0.1uF C310 NRS6045T100MMGK
+24V_AMP
18
1%
50 16V 16V 4700pF
51 C314
C309 R314 2200pF C328 OPT
+3.3V_NORMAL 330pF C343
+3.3V_NORMAL 50V C334
52 0.047uF 470 50V 0.1uF 2200pF
C320 C321 50V 50V
0.1uF 10uF
50V
SPEAKER_L
SSTIMER
35V
PVDD_AB_2
PVDD_AB_1
VR_ANA
PLL_FLTP
PLL_FLTM
C330
BST_A
OUT_A
0.47uF
AVSS
PBTL
NC_2
NC_1
C327 OPT
50V C342 P304
330pF C333 2200pF
R305 C304 50V 0.1uF 50V
[EP]
12
11
10
9
8
7
6
5
4
3
2
1
0.1uF 50V
1/16W
4.7K
R320
16V AVDD 13 48 PGND_AB_2
SPK_L+
18
1%
R313 A_SEL_FAULT PGND_AB_1 4
THERMAL
14 47
MCLK OUT_B L306
2.2K 46
49
AUD_MASTER_CLK 15 SPK_L-
Need to Check. R312 OSC_RES NC_6 SPK_L-
16 45 10.0uH 3
C326 NRS6045T100MMGK
18K 1% DVSSO 17 44 NC_5 0.033uF
VR_DIG BST_B 50V
AMP_MUTE 18 IC300 43
SPK_R+
PDN 42 BST_C 2
19
OPT OPT LRCLK TAS5733 41 NC_4
C302 20 C325
R304 C308 SCLK NC_3 SPK_R-
0 1000pF 21 40 0.033uF 1
0.1uF L304
POWER_DET 50V 16V SDIN 22 39 OUT_C 50V
SPK_R+
SDA 23 38 PGND_CD_2 10.0uH
SCL PGND_CD_1 NRS6045T100MMGK
1/16W
24 37
+3.3V_NORMAL
R319
25
26
27
28
29
30
31
32
33
34
35
36
18
1%
AUD_LRCK OPT
AUD_SCK C341
C332 2200pF
PVDD_CD_1
PVDD_CD_2
RESET
STEST
DVDD
DVSS
GND
AGND
VREG
GVDD_OUT
BST_D
OUT_D
AR301
1/16W
330pF 50V
+24V_AMP 50V C329
AMP_SDA OPT
0.47uF C340
AMP_SCL C323 50V 2200pF SPEAKER_R
330pF C331 50V
AMP_RESET 50V 0.1uF
C319 C322 50V
0.1uF 10uF
1/16W
+3.3V_NORMAL 50V
R318
C313 35V
C307
18
1%
0.1uF
0.1uF 16V
16V L303
SPK_R-
C316 C317 10.0uH
OPT 1uF 0.033uF NRS6045T100MMGK
ZD300 25V 50V
5V C311
0.1uF
16V
Copyright ⓒ 2014 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
EXTERNAL INTERFACE HDMI_1(REAR)
OPT
R416
10K
AV/COMPONENT Q400
C
B
R417
10K
5V_DET_HDMI_1 MMBT3904(NXP) HPD1
+5V_NORMAL
JK401 JK404 SHIELD R412
E
1K
PPJ245N2-01 20
R420 R421
4.7K 4.7K
6E [RD2]E-LUG R409
10K
19
R411
OPT DDC_SDA_1
18 2.7K VR409
COMP_R_IN R414
OPT 4.7K DDC_SCL_1
17 VR405
VR403 R402 OPT
C402 R408 16 OPT OPT
OPT
14
OPT
13
EAG59023302
D403
4E [RD2]CONTACT R406
10K
12 4 3
L401
IP4283CZ10-TBA
DLP11SA900HL2L 1 10 CK-_HDMI1
COMP_L_IN 11
CK+ HDMI_REAR_EMI_FILTER
10 2 9 CK+_HDMI1
1 2
R401 OPT +3.3V_NORMAL D0-
VR401 470K C401 R407 9 3 8
OPT
5D [WH]O-SPRING 1000pF
50V
12K
8
D0_GND
4 3
L402
DLP11SA900HL2L
4 7 D0-_HDMI1
AR401
1/16W
D0+ HDMI_REAR_EMI_FILTER
5 6 D0+_HDMI1
7
10K
1 2
D1-
6
COMP_DET 4 3
4C [RD1]CONTACT OPT
5
D1_GND
D1+
L403
DLP11SA900HL2L
1 10 D1-_HDMI1
HDMI_REAR_EMI_FILTER
VR402 4 2 9 D1+_HDMI1
1 2
D2-
3 3 8
4 3
D2_GND 4 7 D2-_HDMI1
5C [RD1]O-SPRING 2
D2+
L404
DLP11SA900HL2L
D2+_HDMI1
ICVS0518150FR_
5 6
HDMI_REAR_EMI_FILTER
COMP_Pr+
CVBS_OUT 1
1
VR407
2
D402
IP4283CZ10-TBA
ZD404 OPT OPT
[RD1]E-LUG-S R405
VA402
75 5%
7C
OPT
ZD405 comp-shape=2012
+3.3V_NORMAL
5B [BL]O-SPRING
ICVS0518150FR_
COMP_Pb+
CVBS_OUT
ZD402 IC401 CVBS_OUT
[GN/YL]CONTACT R404
MM1756DURE C411
0.1uF HDMI_2(SIDE)
VA401
75 5%
4A ZD403
OPT
comp-shape=2012 DTV/MNT_VOUT
VCC IN
6 1
CVBS_OUT
PS GND C415 R419
5 2 0.1uF 33
5A [GN/YL]O-SPRING CVBS_OUT
R410
1/16W
HPD2
75 OUT BIAS 5%
AV_DET 4 3 5V_HDMI 5V_DET_HDMI_2
+5V_NORMAL +3.5V_ST
OPT
VR400 GND
A1
A2
6A [GN/YL]E-LUG JK403 BODY_SHIELD MMBD6100
D401
CVBS_OUT
20
C
C410
4.7uF 19 HP_DET OPT
ICVS0518150FR_
VR408
AR402
1/16W
COMP_Y+ R413
4.7K
18 5V
2.7K R415
17 GND 4.7K DDC_SDA_2
ZD401 OPT
R403
DDC_DATA VR404
VA400
75 1% 16 DDC_SCL_2
OPT
ZD400 comp-shape=3216
15 DDC_CLK
14 NC OPT OPT
VR411 VR412
13 CE_REMOTE
OPT
EAG62611204
12 CK- D405
IP4283CZ10-TBA
11 CK_GND
D0-
1
2
10
9
CK-_HDMI2
CK+_HDMI2
9 3 8
D0_GND 4 7 D0-_HDMI2
8
JK400 OPT D0+ 5 6 D0+_HDMI2
KJA-PH-1-0177 1/16W 7
R400
0 5% D1-
IC400 C407 C409 6
6 M6 MAX3232CDR P401 OPT
22uF 22uF D1_GND
C400 ZD406 5
0.1uF 5V 10V 10V 1 10 D1-_HDMI2
1 M1 D1+
3AU04S-305-ZC-(LG)
4
1
D2-
3 M3_DETECT 3 3 8
C406
0.1uF D2_GND
2
GND V+ SIDE_USB_DM 2
4 7 D2-_HDMI2
AR400 15 2
4 M4 D2+ 5 6 D2+_HDMI2
100 1
1/16W C405
3
C403
DIN2 DOUT2 0.1uF
10 7
ROUT2 RIN2
P400 9 8
12507WS-04L
EAN41348201 SPDIF OPTIC JACK
+3.3V_NORMAL
1
SPDIF
2 JK402
JST1223-001
3 GND
1
Fiber Optic
4 VCC
2
JP422
JP423
JP424
JP425
VINPUT
3
SPDIF_OUT
4
SPDIF
C408 C412
FIX_POLE
ESD Ready
Copyright ⓒ 2014 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes
3.3V_NORMAL -> 3.3V_TU
TUNER for ATSC W/O Isolator
+3.3V_NORMAL
+3.3V_TU
L500
PZ1608U121-2R0TF
+3.3V_TU
R502 R503
AR500 1.8K 1.8K
33
1/16W
TU_SCL
TU_SDA
OPT OPT
C501 C504 C505 C506
15pF 15pF 20pF 20pF
TU500 50V 50V 50V 50V
TDSS-H701F
NC_1
1
NC_2
2
SCL
3
SDA
4 +3.3V_TU
+B1[3.3V]
5
NC_3
6
NC_4
7
NC_5
8
C500 C503
IF_AGC
9 100pF 0.1uF
DIF[P] 50V 16V
10
DIF[N]
11 1. should be guarded by ground
close to the tuner pin 2. No via on both of them
B1 A1 IF_AGC_MAIN 3. Signal Width >= 12mils
B1 A1
Signal to Signal Width = 12mils
C502 should be guarded by ground
Ground Width >= 24mils
0.1uF
12 16V
SHIELD
R501
33
IF_P_MSTAR
R500 1/16W
33
5% IF_N_MSTAR
1/16W
5%
Copyright ⓒ 2014 LG Electronics. Inc. All right reserved. LGE Internal Use Only
Only for training and service purposes