Professional Documents
Culture Documents
27F520T M134C PDF
27F520T M134C PDF
Operating Conditions Note: Many factory alignments appear in the menus but B+ Adjustment Focus Adjustment
Unless otherwise noted, the following conditions must be only the ones listed here can be changed. The values 1. Tune the instrument to receive a crosshatch signal. Test Point: Observe Display
observed when aligning this chassis: can be accessed and the value (hex number) on the Adjust: Focus Control Flyback
screen can be changed but the actual value the 2. Set the Preset Picture Mode to normal.
Chassis must be operated from a 120VAC isolation 3. Adjust VR802 for 130Vdc +/- 0.5V at C422+ (B+).
instrument is using cannot be changed except at the
transformer, with line voltage set to 120VAC (±2.0V). factory using special equipment. 1. Tune the instrument to receive a crosshatch signal.
RF AGC Adjustment
Picture controls (color, brightness etc.) must be set to The following is a list of all the menus and a 2. Adjust the Focus control for best overall focus.
midrange. The RF AGC has been preset at the time of manufacture
description of the individual adjustments under
Procedures must be performed in the sequence given. for optimum operation over a wide range of RF signal
each Main menu that can be changed. Only the
A 10X probe must be used for oscilloscope and frequency following menu items can actually be adjusted. input conditions. Readjustment should not be required Color Temperature Adjustment
measurements. unless the tuner has been repaired or unusual signal con- Test Point: Observe Display
The audio output leads must not be shorted together or to Menu 1 (Remote key: 1) ditions exist such as: Adjust: Menu 1 RC (Red Cutoff)
ground with the chassis on. Item Remark a. Cable TV—adjacent channel interference. Menu 1 GC (Green Cutoff)
All video signals must have -40 IRE sync tips unless b. Picture bending and/or channel 6 color beats which are Menu 1 BC (Blue Cutoff)
RC R cut-off setting
Menu 1 GD (Green Drive)
specified otherwise. GC G cut-off setting usually due to excessive RF signal input. This occurs
Menu 1 BD (Blue Drive)
Chassis AC power must be removed for 10 seconds before BC B cut-off setting when the receiver location is too close to the transmitting
disconnecting any cable. GD G drive setting tower. It may also occur when the receiver is connected
A 3-minute warm-up is required for chassis or module to an antenna distribution system where the RF signal 1. Perform the Screen adjustment.
BD B drive setting
related alignments. A 15-minute warm-up is required for has been amplified. The signal should be attenuated at 2. Set the Picture color temperature to Normal and set all
Kine related alignments. Menu 2 (Remote key: 2) the antenna input to a more satisfactory level. of the picture controls (brightness, contrast etc.) to
Item Remark c. Picture Noise caused by “broadcast noise” or weak sig- midrange.
Required Test Equipment HIGH6 60Hz height nal. If the broadcast is “clean” and the received signal is 3. Tune the instrument to receive a grayscale stairstep test
- Dual-Trace Oscilloscope VP60 Vertical position at least 1 mV, the picture will be noise free in any area. pattern.
- Digital Voltmeter VLIN6 60Hz Vertical linearity NOTE: Adjustment of the RF AGC parameters may not have 4. Enter the Service mode and adjust the values for the Cut-
- Frequency Counter VSC6 Vertical S correction (60Hz) any visible effect except under unusual conditions. off and Drive controls to obtain proper color tracking
- Audio Signal Generator Adjusting the RF AGC to one extreme of it’s (no tinting - only black, white and shades of gray). Cor-
- NTSC Signal Generator (B&K 1249, or equivalent) Menu 3 (Remote key: 3) parameter limits will usually provide a relatively rect color temperature is 9300 degrees - X=284 Y=299.
- MTS Signal Generator (B&K 2009, or equivalent) Item Remark poor signal-to-noise ratio, while adjustment to the 5. Check the low light to high light gray scale tracking (black
- Sweep/Marker Generator (or Standard Signal Generator) HPOS6 Horizontal position (60Hz) other extreme of it’s parameter limits will cause a
and white picture). Should any color other than gray or
- DC Power Supply (5.0V/0.25A) for TAG001 degradation of overload conditions such as channel 6
PARA6 Parabola white be dominant in low light to high light areas the
color beats or Cable TV adjacent channel
TRAP6 Trapazoid interference. Use the weakest local signal to adjust color temperature settings have not been properly set.
HSIZE Horizontal size RF AGC parameter setting (Menu 8). If the RF AGC Repeat the procedure if necessary.
Entering the Service mode CNRT6 Corners top parameter setting is adjusted, check all local NOTE: Color Cutoff adjustments affect the low light (dark)
1. Enter the service mode (S-Mode) by pressing the VOL- CNRB6 Corners bottom channels for proper operation. areas while color drive adjustments affect the high
UME DOWN key on the instrument until the volume
light (white) areas.
decreases to minimum. Menu 4 (Remote key: 4) Screen Adjustment
2. Press the INFO key on the remote handset while holding No adjustments allowed Test Point: Observe Display
the VOLUME DOWN key on the instrument. Adjust: Screen Control Flyback
3. Press the PROGRAM UP/DOWN buttons to select the Menu 5(Remote key: 5)
different adjustments under the first menu and press the No adjustments allowed 1. Tune the instrument to receive a crosshatch signal.
VOLUME UP/DOWN buttons to adjust the setting 2. Set the Picture color temperature to Normal and set all
(value). Menu 6(Remote key: 6 )
of the picture controls (brightness, contrast etc.) to
5. Press the OK button to toggle into the Main Menu selec- No adjustments allowed
midrange.
tion mode and select the different Main menu sections 3. Enter the Service mode and preset the Menu 1 values to
using the PROGRAM UP/DOWN buttons. Press the Menu 7( Remote key: 7)
No adjustments allowed RC/GC/BC to 80 AND GD/BD to 40.
OK button again to toggle back into the value adjust-
4. While still in the service mode, press the Input button on
ment mode.
Menu 8 (Remote key: 8 ) the remote control. This will collapse the vertical.
6. Menus up to menu 19 can be selected directly using the
Item Remark 5. Adjust the screen control to just produce a dim horizon-
remote control by pressing digital buttons 1~9, 0, note-
RFAGC RFAGC [12H, bit 5 ~ 0] tal line on the CRT.
book, CAP, Display, Sleep, Calendar, System/INS,
Favourite, Return and Picture.
Menu 9 - 24
7. Press the Sound button to save the new settings and exit No adjustments allowed
the service mode.
S Video Av2 IN
SIF
Av1 IN
Z141
AV Out
SAW
PI F & SI F
CVBS CVBS/YC Y
EEPROM IC 101 Cb
24C08
TMPA8809(M134C) Cr
MCU/V/C/D Y/C
Receiver
CRT Drive
AMP
IC 301V.OUT
37
TDA8177
REMOTE
HANDSET TV Body Button 38 +28V
H OUT
+13V
Power
IC 801 +130V
STR-W6735 +12V
7809 +9V
FBT
7805 +5V Optional Function
Fuse Blown
Figure 1 Fuse Blown
ground?
Yes Yes
No raster abnormal + B
Figure 2 No Raster, Abnormal +B
Voltage
No Yes
Yes
No raster, +B ok
Is there an
Is +9V, +5V Y Yes Waveform at C Yes Is R461 No Replace
output waveform
Shorted to ground? of Q411? ok? R461
Pin13of IC101?
No
Yes
NO No
Is the drive
Increase
Check/Replace Is Pin2 of IC101 low circuit ok?
VG2
short voltage level?
No Yes NG
Yes
Yes No
No
Is both +14V and -14V ok? Check horizontal scan circuit, such
as C412, C413, C419, etc
Yes
No
Is the signal at Pin SCL, Yes Is the supply voltage Yes Check/Replace
SDA of tuner ok? of tuner ok? Tuner
No No
Check signal at P5, P57, P58, P59,
Check/Replace
and P60 of IC101 and replace the
IC201, IC202, D101.
abnormal related circuits
Yes
Check EEPROM
Figure 5 Sparse Noise
Symptom: raster ok, no
picture, no sound, sparse
noise dots
Yes
Yes
Yes
Yes
Check &
Replace the Tuner Replace Z141 (SAW) repair the IF
pre-amplifier
circuit
No sound Figure 6 No Sound
Yes
Replace
Apply the lead of a multimeter at IC602
RX1KΩ connect one probe to GND, No
Is it mute at P6
use another to touch Pin4, Pin12 of No Check power Yes
of IC602?
IC602, Is there interference noise supply of IC602
from the speaker. Yes Check/Replace
Q601, Q602
and Q603 etc.
Yes
No
No
Check Q917 and
TV has NG
Check P13 of IC901 Video path Circuit
Picture. AV
hasn’t
Picture.
Check P1 of IC101,
Is the waveform at Is the logic at P9,
Yes No P4 of IC1001 and
Pin12, Pin14 of P10 of IC901 ok?
the related circuit
IC901 ok?
No Yes
No Picture
Check Q901 ~
Q904 path circuit
Replace IC901
Replace
IC901
Is the waveform
Is the logic at Yes
at P15 of IC901 Yes
P9, P10 of
ok? Check P1 of IC101, P4 of
AV has IC901 ok?
IC1001 and the related
Picture. TV No
circuit
hasn’t No Is the waveform at
Picture.
P30 of IC101 ok?
Check/Replace R245,
Check/Replace IC101
R311, R313.
Figure 9 No Tuning
Yes
No Check/Repair +33V
Does the channel
power supply
number display No
No
on the screen? Check/Replace
Check the the tuner
Yes No
waveform Is there a
Is the
Start auto- at Pin60, short circuit
No Yes +33V/+5V
search. Is the Pin61 of Yes around the
A power
BUS ok? IC101 integration Check/Repair the
supply Yes
circuit? integration circuit
Yes ok?
Yes
No
Yes
Replace the disabled
No Is the voltage at P5 of components
IC101 ok?
Yes
Yes
Page 1 of 74
M134C
Page 2 of 74
M134C
Page 3 of 74
M134C
Page 4 of 74
M134C
Page 5 of 74
M134C
Page 6 of 74
M134C
Page 7 of 74
M134C
Page 8 of 74
M134C
Page 9 of 74
M134C
Page 10 of 74
M134C
Page 11 of 74
M134C
Page 12 of 74
M134C
Page 13 of 74
M134C
Page 14 of 74
M134C
Page 15 of 74
M134C
Page 16 of 74
M134C
Page 17 of 74
M134C
Page 18 of 74
M134C
Page 19 of 74
M134C
Page 20 of 74
M134C
Page 21 of 74
M134C
Page 22 of 74
M134C
Page 23 of 74
M134C
Page 24 of 74
M134C
Page 25 of 74
M134C
Page 26 of 74
M134C
Page 27 of 74
M134C
Page 28 of 74
M134C
Page 29 of 74
M134C
Page 30 of 74
M134C
Page 31 of 74
M134C
Page 32 of 74
M134C
Page 33 of 74
M134C
Page 34 of 74
M134C
Page 35 of 74
M134C
Page 36 of 74
M134C
Page 37 of 74
M134C
Page 38 of 74
M134C
Page 39 of 74
M134C
Page 40 of 74
M134C
Page 41 of 74
M134C
Page 42 of 74
M134C
Page 43 of 74
M134C
Page 44 of 74
M134C
Page 45 of 74
M134C
Page 46 of 74
M134C
Page 47 of 74
M134C
Page 48 of 74
M134C
Page 49 of 74
M134C
Page 50 of 74
M134C
Page 51 of 74
M134C
Page 52 of 74
M134C
Page 53 of 74
M134C
Page 54 of 74
M134C
Page 55 of 74
M134C
Page 56 of 74
M134C
Page 57 of 74
M134C
Page 58 of 74
M134C
Page 59 of 74
M134C
Page 60 of 74
M134C
Page 61 of 74
M134C
Page 62 of 74
M134C
Page 63 of 74
M134C
Page 64 of 74
M134C
Page 65 of 74
M134C
Page 66 of 74
M134C
Page 67 of 74
M134C
Page 68 of 74
M134C
Page 69 of 74
M134C
Page 70 of 74
M134C
Page 71 of 74
M134C
Page 72 of 74
M134C
Page 73 of 74
M134C
Page 74 of 74
Chassis Part Symbol Defective Circuit Symptom solution
Servicer installed replacement chassis but the parental lock was
turned on, blocking all programming except for commercials. Pressing the vol+ on the
According to the customer instruction book the code was supposed remote & ch+ on the FPA the
m134 None System Control to have been set to 0000. This wasn't the case. password came up as 1111.