Professional Documents
Culture Documents
(Civil Plumbing Electrical Work) For Refurb. of CHC Kothawan
(Civil Plumbing Electrical Work) For Refurb. of CHC Kothawan
4 EARTH FILLING
1.3
Ref.
S.No Description
code
1.3.1 Filling with selected, suitable excavated earth already available at site in
plinths, back of retaining walls, foundations and trenches etc. and
spreading the remaining soil for landscaping and other location as
directed by the Project Manager and shall be done in layers, not
exceeding 20cm in depth and consolidating each deposited layer by
mechanical means, ramming and watering as per specifications
including re-excavation, transportation, loading, unloading, carriage to
5 dumping spot and all incidentals at all depth, levels, leads and lifts
complete. (Net consolidated area fill volume will be computed from the
initial and final levels. Volume in slopes, embankments etc. will be
computed applying appropriate formula, as per CPWD specification).
1.3.2 Supply selected/ approved earth brought from outside the site and filling
the same in plinths, back of retaining walls, foundations and trenches
and spreading in landscaping and other location as directed by the
Project Manager and shall be done in layers, not exceeding 20cm in
depth and consolidating each deposited layer by mechanical means,
ramming and watering as per specifications including transportation,
cost of soil, royalty, loading, unloading, carriage to dumping spot and all
6 incidentals at all depths and levels, for all leads and lifts complete (Net
consolidated area fill volume will be computed from the initial and final
levels. Volume in slopes, embankments etc. will be computed applying
appropriate formula, as per CPWD specification).
(Rates for all cement concrete items plain and reinforced described
below shall include work from Basement Level to top of last roof including
roof of machine room, mumty, over head water tanks and parapets
above at all floors and for all heights, required hacking of the surfaces for
smooth plaster. (This section covers cast in situ structural and
architectural as well as precast structural and architectural concrete
work).
Ref.
S.No Description
code
8 2.1 PLAIN CEMENT CONCRETE
Providing and laying damp proof course 40mm thick with cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggreate
20mm nominal size) including providing and mixing of water proofing
compound @ 2% of cement content and providing and applying two
layers of bitumen of grade 85/25 and as directed by the Project Manager.
Providing & laying cast - in - situ machine batched, machine mixed and
machine vibrated structural controlled cement concrete M25 grade
using concrete pump with 20mm down coarse aggregates excluding cost
of centering, shuttering and steel reinforcement but including cost of
making shear keys and provision of construction / contraction / control
13 2.3.1 joints in various locations, laid, consolidated and cured, item to include
all structural items like foundation, raft slab, raft beams, plinth beam,
sump pits, pedestals / bases of coloum, wall foundations grade slab,
Allow for forming grooves, drip course, chamfers, cut-outs, openings etc.
where called for and for dressing with approved shuttering oil to prevent
adhesion. Unexposed concrete surfaces subsequently left untreated (in
the condition obtained on removal of form work) shall not constitute
exposed concrete work and shall be measured under this item only.
Irregular shapes with sides which may not be perpendicular to each other
for shapes not conforming to rectangle or square shall not be paid
separately. (quoted rate to include all staging upto any height).
(Quoted Rates are for all heights, depths, levels, leads and lifts and for all
design and pattern shown in drawings)
Providing and applying 6mm thick plaster to RCC slab in cement mortar
1:4 (1 cement : 4 fine and coarse sand in equal proportion) finished
smooth including scaffolding, curing, making grooves at desired location
etc. complete as per drawing.
7.5 Providing and fixing precoated galvanised iron profile sheet (size, shape
and pitch of corrugation as approved by engineer- in-charge)..50mm
(+.05%) total coated thickness with zinc coating 120 grams per sqm as
per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both
side of the sheet and polyester top coat 15-18 micron. Sheet should have
protective guard film of 25 microns mimnimum to avoid scratches during
transportation and should be supplied in single length up to 12 Meter or
as desired by engineer-in-charge, The sheet shall be fixed using self
34 drilling/ self tapping screws of size ( 5.5x55mm) with EPDM seal,
complete upto any pitch in horizontal/ vertical or curved surface,
excluding the cost of rafter and trusses and including cutting to size and
shape whereever required. (Make Jindal/Tata/Everest or equivalent)
Prviding & Fixing M.S. Mosquito Net on Windows & Vantilations including
35 7.6 all hardware necessary fittings as directed by EIC.
9.10.1 Providing and fixing Glazing with 6mm thick clear glass of approved
make duly toughened with Approved in Aluminium Doors, windows,
vantilators, shutters and Partitions etc with EPDM Gasket (gasket to be
43 paid under relevent item) etc. complete as per directed by EIC. The rates
are inclusive all other necessary hardwares/fittings etc. complete as per
directed by EIC.
9.10.2 Providing and fixing Glazing with 6mm thick plain float glass of approved
44 make complete in all respect including all other necessary
hardwares/fittings etc. complete as directed by EIC.
Ref.
S.No Description
code
9.10.3 Providing and fixing powder coated aluminium door frame (chowkhat)
section 100 mm x 40 mm x 2.5 mm thick (JINDAL B 9287) or equivalent
as per architectural drawings fabricated out of anodised aluminium built-
up extruded sections of alloy conforming to IS designation HE 9 WP/HV 9
WP alloy with chemical composition and technical properties in
accordance with IS 733 and IS 1285 respectively ( Powder coating shall
be at least 55 microns thick using pure polyester epoxy of approved
colour and manufacture), designed to deflection up to L/175 of span at
45
wind-load of 150kg/sqm in accordance with IS.875 , joints mitred and
jointed with heavy duty aluminium angle pieces with fins to match the
sections of the frame by crimping and fixed with nickel plated steel
screws (Nettlefold or equivalent) (Rates are inclusive of all Hardware
fittings as directed by EIC.)
Providing and laying tile flooring of approved make, shade & make as
approved by Architect laid over 20/12mm thick bed of cement mortar
1:4 (1 cement : 4 coarse sand), joint to be filled with siliconsealent to
match the shade of tile of approved brand, cutting of tiles as per requred,
making holes for light fixtures& laid as per design & drawing approved by
Architect for various thickness of tiles.
Kota Stone slab flooring over 20mm (average) thick base laid over and
jointed with grey cement slurry mixed with pigment to match the shade
of the slab, including rubbing and polishing complete with the base of
cement mortar 1:4 (1cement : 4 coarse sand) as per directed by EIC.
Providing and laying machine cut pre-polished stone slab in required size
of approved quality in counters fixed over average 20 mm thick cement
mortar 1:4 (1 cement : 4 coarse sand) and joints neatly finish with
cement paste mixed with matching pigment including edge chamfering,
making moulding as per design and drawing, making openings/ holes for
sink/ wash basin, mixers, soap dispenser, facia etc. as required and
mirror polishing of moulding and cut edges, filling silicon at junctions with
sanitary fixtures and corners with wall whereever required etc complete
as per drawing.
10.7.1 With 18 mm thick Prepolished Baroda Green stone and joint to be filled
with white cement slurry mixed with pigment to match the shade of
56 stone including exposed edge polishing, complete. (Basic rate of
prepolished Granite stone Rs.880/- per Sqm)
Ref.
S.No Description
code
Painting (Two or more coat) with superior synthetic enamel such as Luxol
3, Hi-glossapcolite superlac, dulux specified brushing to give an even
shade on old surfaces (Door window and steel surface).
Note:- Paint shall be applied after proper preparation of the surface.
Finishing wall with water proof cement paints two or more coat of
approved make such Super Snowcem, Durroem, Robiacem, Guttucem
Supercem quality and of required shade on undecorated wall surfaces
(one coat) over and including one coat white cement primer to give and
60 11.6
even shade after thoroughly preparation of surface (existing/new)
including brushing, cleaning to powered materials including curing and
cost of all materials.
Ref.
S.No Description
code
61 12 Expansion Joint
Providing and fixing 150 mm wide sheet covering over expansion joints
66 12.2 with iron screws as per design to match the colour / shade of wall
treatment.
cum. 50 75 3750
46250
Unit Quantity Rate Amount (Rs.)
Kg 755.83 60 45349.5
99562
34152
232001.74
4900
Unit Quantity Rate Amount (Rs.)
834803.61
Unit Quantity Rate Amount (Rs.)
Kg 5081.3 85 431910.5
725694.5
110115.025975
Kg 25 300 7500
172288.5
720205.96
789444.05
120000.00
80000.00
1.1
2.1
2.2
3.1
3.2
Ref.
Code
4.1
4.2
5.1
8
8.1
8.2
8.3
10
11
12
1
Ref.
Code
1.1
1.2
2.1
5
BOQ - MEP-CHC (Kothawan)
DESCRIPTION
MEP WORKS
PLUMBING-Sanitary fixtures
Note: All Consumables like chrome plated brass or GI, nuts bolts, screws,
washers, as required C.I. Brackets, fasteners, rawl plugs, cement, sand etc.
are in the scope of Contractor and rates should be inclusive of these, except for
the items specifically mentioned as owner's supply (if any) , all other materials,
consumables are deemed to be the part of contractor's scope.
Providing and fixing of water closet squatting pan (Indian type W.C. Pan) with 100mm
sand cast iron "S" or 'P" trap, 10 litre low level white P.V.C. flushing Cistern, including flush
pipe, with manually controlled device (Handle lever) conforming IS:7231, with all fittings
and fixtures complete, including cuttong and making good the walls and floors wherever
required:
Providing and fixing white vitreous china pedestal type water closet (Europian type
W.C. Pan) with seat lid, 10 litre low level white P.V.C. flushing Cistern, peincluding flush
pipe, with manually controlled device (Handle lever) conforming IS:7231, with all fittings
and fixtures complete, including cuttong and making good the walls and floors wherever
required:
W.C. Pan with ISI marked white solid plastic seat and lid
P/F White Vitreous China flat back or wall corner type lipped front urinal basin of
430x260x350mm size with all necessary fittings and accessories as per list of make.
P/F wash basin with C.I. Brackets,15mm C.P. Brass pillar taps, 32 mm C.P. Brass waste of
standard pattern, Including painting of fittings and brackets ,cutting and making good the
walls wherever require: (as per list of make).
White viterous china wash basin size 550X400 mm with a single of 15mm C.P. brass pillar
tap
White vitreous china surgeon type wash basin of size 660X460 mm with single 15 mm C.P.
Brass pillar taps with elbow operated levers ISI marked
Providing & Fixing Stainless Steel A ISI 304 (18/8) Kitchen sink as per IS 13983 with C.I.
Brackets and stainless steel plug 40mm, including apintingg of fittings and brackets,
cutting & making good the walls wherever required
Kitchen Sink without drain board (Size 610X510 mm Bowl depth 200 mm)
Providing & fixing of 15 mm C.P. brass pillar tap for kitchen sink
DESCRIPTION
Providing & fixing G.I. Pipes complete with G.I. Fittings and clamps, i/c making good the
walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting
chases and making good the wall
Providing and fixing G.I. Pipe Complete with G.I. Fittings and clamps including painting of
synthetic enmel paint of 2 coats over one coat of primer of approved shade and color etc.
(external Work)
25 mm dia nominal bore
Providing & Fixing of water tank (1000Ltr) with all fitttings and accessories on platform
including connections of water supply line,vent, drain line & overflow line etc.
Making of PCC platform for water storage tank on terrace as per size of water tank or as
directed by engineer incharge.
Providing & Fixing ball Valve (Brass) of approved quality of the following size
20 mm dia
25 mm dia
32 mm dia
Providing & Fixing C.P. brass short/long body bib cock of approved quality confirming to IS
8931
Providing & Fixing P.V.C. waste pipe for sink and wash basin including P.V.C. waste fitting
complete (Flexible pipe 40 mm dia)
Providing and fixing of 450mm long S.S braided EPDM lined flexible connector with nuts
washers and all necessary fittings complete in all respects. (As per list of make)
Providing and fixing 15 mm dia C.P. angle valves with S.S wall flange complete in all respects.
(As per list of make)
Providing, fixing & testing uPVC pipes confirming to IS 13592 (Type B) SWR for soil, waste
and vent system alongwith all required fittings like tees, bends, crosses with or without
access doors jointed with approved solvent cement as per manufacturer's
recommendations, fixed to walls and ceilings with clamps complete including cutting and
making good the floors and walls where required complete in all respects.
DESCRIPTION
75 mm OD
110 mm OD
Providing, fixing & testing uPVC pipes confirming to IS 13592 (Type A) SWR for rain water
system alongwith all required fittings like tees, bends, crosses with or without access doors
jointed with approved solvent cement as per manufacturer's recommendations, fixed to
walls and ceilings with clamps complete including cutting and making good the floors and
walls where required complete in all respects. Make Prakash/Kisan or equivalent)
110 mm OD
Providing & Fixing of uPVC "P" trap (125X 110 mm) including connection in pipe, cutting
the floor and making good etc.
Providing & Fixing of uPVC Nahani rap of the size 110 mm dia including connection in pipe,
cutting the floor and making good etc.
Providing & Fixing of CP jali of the approved quality of the required size as per drain
provision in the toilet and kitchen.
Grand Total
BOQ
UNIT Rate Amount
Qty.
Nos. 42 60 2,520
655,125
655,125
Sr. Item Description QTY UOM Supply
No Rate
A LUMINAIRES & FANS
1 Single LED Tube Light 20-Watt with wall mounted Batten 150 Nos 300.00
fixtures , Polycarbonate Housing and integrated electronic
driver
2 Twin LED Tube Light 2 x 20-Watt with wall mounted Batten 20 Nos 700.00
fixtures , Polycarbonate Housing and integrated electronic
driver
3 LED Street Light 25 Watt with cast Aluminium housing, 10 Nos 1,800.00
separate LED driver compartment with IP66 ingress
protection, impact resistance of IK-07 and 10kV built-in SPD
complete with wall-mount brackets & fixtures
4 Celing Fan, 1200 mm sweep, 390 RPM, White Colour with 30 Nos 1,500.00
double ball bearing arrangement complete with anchoring
sockets
B POINT WIRINGS
1 Supply, Laying, Testing and Commissioning of 'Single LED Tube 150 Points 250.00
Light Point' Wiring with 3 Runs of 1.5 sq.mm., FRLS type PVC
insulated multi strand copper cables of 1.1kV grade through
existing Concealed Conduits inside the Rooms along with 1no.
6A One-way switch, fitted into a Modular Front Plate with
Base Frame and Surface Mount PVC Moulded Enclosure and
other accessories as required as per the site conditions . The
Ferrules identification to be done at the both end (Cable
length of average 6 Mtr. per Point to be considered)
2 Supply, Laying, Fixing, Testing and Commissioning of 'Power 1600 Mtrs 60.00
Circuit' (from SP MCB to Room Junction Box) with 3 Run of 2.5
sq.mm. PVC insulated FRLS multi strand copper flexible Cables
of 1.1kV grade layed in UPVC Round Rigid MMS type Conduits
of 25 mm. dia. size, and wall-fixing with saddles, Round
Inspection Box and Radial type Bend and other associated
accessories as required as per the site conditions. (Only 3nos.
circuits, each comprising of P-N-E : 9nos. single core cables are
allowed to be layed through a common 25mm PVC Conduits)
2 Supply, Laying, Fixing, Testing and Commissioning of 'Sub Main 370 Mtrs 150.00
Power Circuit' (Main LT Panel to SPN DBs) with 3-Core, 6.0
sq.mm. multi Strand, Copper, PVC Insulated and PVC
sheathed, 1.1kV grade, Power Cables layed in UPVC Round
Rigid MMS type Conduits of 25mm. dia. size, and wall-fixing
with saddles, Round Inspection Box and Radial type Bend and
other associated accessories as required as per the site
conditions .
H EARTHING SYSTEM
1 Supply, testing and commissioning of Maintenance free 2 Nos. 7,500.00
earthing with Copper Bonded Rod of 3 Mtr length and the
earth pit shall be filled & packed with highly conductive and
anti corrosive chemical compound. Earth Pit Chamber shall be
provided for inspection and connection. 25 mm x 6 mm thick
GI strip shall be nut bolted to connect the earthing
strips/Leads . The electrode shall be provided with 2 x 25kG
earh conductivity enhancing chemical compound as per
specification
I LIGHTNING PROTECTION
1 Supply, Installation, Testing and Commissioning of ESE Type 2 Nos. 50,000.00
active lightning conductor designed to conform to the
Standard NF C 17-102 ΔT: 30 μs ( Jul 1995 ) complete with 5
mtr Must of dia 50 mm. and base plate, Down Conductor of GI
Strip of size : 25 x 6mm, Bus bar Test Link, 2nos maintenance
free Earth Pits with Copper bonded earth electrodes, 2 x 25kG
Bag of earth conductivity enhancing chemical compounds as
per specification.
-
-
37,500.00 150.00 22,500.00
-
-
3,500.00 20.00 2,000.00
Erection
Amount Rate Amount
4,500.00 20.00 2,000.00
-
-
72,000.00 20.00 32,000.00
-
-
Erection
Amount Rate Amount
37,000.00 40.00 14,800.00
-
-
32,000.00 500.00 4,000.00
-
-
Erection
Amount Rate Amount
50,000.00 5,000.00 5,000.00
-
-
15,000.00 2,500.00 5,000.00
-
-
100,000.00 10,000.00 20,000.00
816,600.00 212,650.00