Professional Documents
Culture Documents
QB Tech
QB Tech
ANS: b
ANS: c
a.Option 1 and 2
b.option 1 and 3
c.Option 2 and 3
d.All the above
ANS:
ANS:
Q5. During the normal start of a gas turbine engine
ANS:
a. Whirling of shaft
b. Bucking of shaft
c .Movement of the shaft in the axial direction
d. None of these
ANS: a
Q7. High Pressure Turbine blades are cooled using air from
a. Ambient atmosphere
b. High Pressure Compressor
c. Low Pressure Compressor
d. None of the above
ANS:
ANS:
Q9. "Most common type of bearing used in a gas turbine engine are
a. ball bearing
b. roller bearings
c. plane bearing
a. Option 1 and 2
b. Option 1 and 3
c. Option 2 and 3
d. All the above
ANS: c
a. Option 1 and 2
b. Option 1 and 3
c. Option 2 and 3
d. All the above
ANS:
Q11. Advantage of shrouded High Pressure Turbine blades is
ANS:
Q12.A high Pressure compressor Blade is found to have a crack near the root
a. The blade has to be rejected for further operation as root is a high stress
area
b. The blade is accepted bal for further service operation
c. Compressor blades can never develop cracks at the root
d. None of the above is correct
ANS: a
Q13. A Blisk is a
a. Bladed Disc-ans
b. Bladed drum
c. Location where shaft meets the disc
d. None of these
ANS: a
a .Increase-ans
b. Decrease.
c. Initially increase and then decrease
d .None of these
ANS: a
a. Re-distribution of weight
b. Addition of weight
c. Removal of weight
d .All the above
ANS: d
Q17. High by pass ratio engines give
ANS:
a. Overhaul burden
b .Line maintenance burden
c. Cost of Ownership
d. None of the above
ANS:
ANS:
ANS:
Q1. Shot-peening is a process used for introducing a
ANS:
Q2. The Oil system in Turbofan engine has the following roles
ANS:
Q3. Variable geometry inlet duct are used on supersonic aircrafts for
a. Slowing the airflow to subsonic speeds at the face of the compressor and
increase static pressure
b .accelerating the airflow, to supersonic speeds, during cruising flisht
c. Increasing the airflow, at outlet end of compressor
d. None of these
ANS:
a.Option 1 and 2
b.Option 1 and 3
c.Option 2 and 3
d All the above
ANS:
ANS:
a.More
b.Less
c.Equal
d.Not adequate
ANS:
ANS:
ANS:
a. The fin
b. the wing dihedral
c. the horizontal tail plane
d. None of the above
ANS:
Q11. What are the types of rivets that are used in Aerospace Industry
a.Solid river
b.Hollow river
c.Blind river
a.Option 1 and 2
b.Option 1 and 3
c.Option 2 and 3
d. All the above
ANS:
a.lift,weight,thrust
b.Lift.drag,weight
c.Lift and weight only
d.None of the these
ANS:
Q13. Which of the following properties makes titanium ideal for fan baldes
a. It is very light
b. It is very leap
c. It is silver coloured
d. all the above
ANS:
a. Welding
b. Brazing
c. Thermal spray Technique
d. Mechanical Fastner
ANS:
ANS:
Q16. The component used for transferring axial thrust form a rotating
component to a static component is
a. Roller Bearing
b.Thrust Bearing
c. Ball Bearing
d. Both 2 and 3 above
ANS:
Q17. The boundary layer is
a. Landing
b. Acceleration and climb
c. Decelerating aircraft
d. Cruise
ANS:
a.Increase
b.Decrease
c.remains constant
d.None of the above
ANS:
a.Pitch
b.Roll
c.Yaw
d.All the above
ANS:
a.Visual inspection
b.Dimensional inspection
c. Non destructive Inspection
d. All the of the above
ANS:
ANS:
a.Option 1 and 2
b.Option 1 and 3
c.Option 2 and 3
d. all the above
ANS:
ANS:
ANS:
a.Option 1 and 2
b.option 1 and 3
c.Option 2 and 3
d.All the above
ANS:
a. Re-distribution of weight
b. Addition of weight
c. Removal of weight
d .All the above
ANS:
ANS:
ANS:
Q6. A Blisk is a
a. Bladed Disc-ans
b. Bladed drum
c. Location where shaft meets the disc
d .None of these
ANS:
Q7. "Most common type of bearing used in a gas turbine engine are
a.ball bearing
b.roller bearings
c.plane bearing
a.Option 1 and 2
b.Option 1 and 3
c.Option 2 and 3
d. All the above
ANS:
ANS:
ANS:
ANS:
ANS:
a.Option 1 and 2
b.Option 1 and 3
c.Option 2 and 3
d.All the above
ANS:
ANS:
Q14. A high Pressure compressor Blade is found to have a crack near the root
a. The blade has to be rejected for further operation as root is a high stress
area
b. The blade is accepted bal for further service operation
c. Compressor blades can never develop cracks at the root
d. None of the above is correct
ANS:
ANS:
ANS:
ANS:
a. Overhaul burden
b. Line maintenance burden
c. Cost of Ownership
d. None of the above
ANS:
a. Increase-ans
b. Decrease.
c. Initially increase and then decrease
d. None of these
ANS:
Q20. High Pressure Turbine blades are cooled using air from
a. Ambient atmosphere
b. High Pressure Compressor
c. Low Pressure Compressor
d. None of the above
ANS: