Professional Documents
Culture Documents
Ms Office 2016 Key
Ms Office 2016 Key
A. True B. False
Answer: Option A
Explanation:
A. DC circuits only
B. AC circuits only
Answer: Option B
Explanation:
3. In a thyristor the gate lead is connected to the n layer near the p layer to which anode is
connected.
A. True B. False
Answer: Option B
Explanation:
Answer: Option D
Explanation:
A. natural commutation
B. auxiliary commutation
C. complementary commutation
Answer: Option C
6. Which converter is used in HVDC transmission?
A. 3 pulse
B. 6 pulse
C. 12 pulse
D. 24 pulse
Answer: Option C
Explanation:
Reason (R): The turn off time of SCR is about 10 to 300 ms.
Answer: Option B
Explanation:
8. An n pulse rectifier is fed by a source having an inductance L. If load current is I 0, the voltage
drop due to overlap is
A.
B.
C.
D.
Answer: Option A
9. Which chopper circuit operates in all the 4 quadrants?
A. A B. C
C. D D. E
Answer: Option D
Explanation:
10. A single phase cycloconverter feeds a resistance heating load. The heating power is provided by
Answer: Option C
11. A 3 phase fully controlled bridge converter is fed by a 3 phase system having phase voltage v =
Vm sin ωt. The firing angle is . The dc output voltage is
A.
B.
C.
D.
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
12. Which of these commutation methods uses an external pulse for commutation?
A. Class A
B. Class C
C. Class E
D. Class F
Answer: Option C
Explanation:
13. In a single phase full wave regulator feeding an R-L load, the power factor angle of load is θ. The
range of control of firing angle is
A. 0≤ ≤
B. θ≤ ≤
C. 0≤ ≤ ( - θ)
D. θ≤ ≤ ( + θ)
Answer & Explanation
Answer: Option B
Explanation:
14. A separately excited dc motor is run from a dc source through a chopper. At 600 rpm and rated
torque, the duty cycle of chopper is 0.8. At 600 rpm and half the rated torque, the duty cycle is
likely to be
A. 0.9 B. 0.8
C. 0.75 D. 0.6
Answer: Option C
Explanation:
A. tunnel diode
B. UJT
D. PIN diode
Answer: Option B
16. In a 3 phase bridge inverter with 180° mode of operation the numbers of thyristors conducting at
one time are
A. 1 B. 2
C. 3 D. 4
Answer: Option C
Explanation:
B. 3 quadrants
C. 2 quadrants
D. 1 quadrant
Answer: Option C
Explanation:
18. In a 3 phase semiconverter, the freewheeling diode comes into operation only if firing angle
A. is zero
B. is 60°
Answer: Option C
Explanation:
19. In the circuit of figure, the load current when thyristor is off
A. is constant
B. increases exponentially
C. decreases exponentially
D. Zero
Answer: Option C
Explanation:
20. A full bridge inverter is fed by a battery of 30 V. The rms value of output voltage is
A. 15 V
B. 152 V
C. 30 V
D. 302 V
Answer: Option C
Explanation:
21. In brushless excitation system of modern alternators, the main exciter is
A. dc generator
B. ac generator
C. either dc or ac generator
D. induction generator
Answer: Option B
Explanation:
B. both p-n-p
C. both n-p-n
Answer: Option A
Explanation:
A. is constant
Answer: Option C
Explanation:
D. outside n layer
Answer: Option B
Explanation:
25. In a 3 phase full converter, the firing angle is less than 60°. The instantaneous output voltage
Answer: Option A
26. In a stud mounted SCR, the stud is
A. in thermal contact with heat sink
Answer: Option C
Explanation:
Answer: Option A
Explanation:
Answer: Option A
Explanation:
29. The characteristics of which device has peak point and valley point
A. SCR
B. PUT
C. SCS
D. Shockley diode
Answer: Option B
Explanation:
30. In a step down chopper using time ratio control, the input voltage is V and duty cycle is . The
load is purely resistive having resistance R. The average and rms load currents are
A.
B.
C.
D.
Answer: Option B
A. about 0.5
B. about 2
C. about 5
D. about 20
Answer: Option C
Explanation:
D. turn on time may be equal, less than or more than turn off time
Answer: Option C
Explanation:
Answer: Option C
Explanation:
A. SUS
B. SBS
C. SCS
Answer: Option C
Explanation:
No answer description available for this question. Let us discuss.
A. dual converter
B. full converter
C. semi converter
Answer: Option A
36. A single phase half wave converter is feeding a resistive load. Output dc power is Pdc and total
power delivered to load is Pac then
Answer: Option D
Explanation:
A. UJT
B. PUT
Answer: Option C
Explanation:
38. In integral cycle control of ac regulators, the period of integral cycle control, i.e., (m + n) T should
be
D. very high
Answer: Option A
Explanation:
39. All other parameters remaining the same, a 3 phase bridge inverter with 180° mode of operation
Answer: Option B
Explanation:
Answer: Option A
41. If a step down chopper is fed by a dc voltage V with Ton and Toff are on and off periods
then is
Answer: Option A
Explanation:
42. A voltage VBB is applied across the terminals of a UJT. The emitter voltage at peak point is
A. hVBB
B. (h + 1) VBB
C. hVBB + VD
D. VD
Answer: Option C
Explanation:
A. True B. False
Answer: Option A
Explanation:
44. In the circuit of figure, the waveshape of load current when thyristor conducting is
A. constant
B. increasing exponentially
C. decreasing exponentially
Answer: Option B
Explanation:
45. In the basic series inverter circuit, the source supplies load
Answer: Option A
46. A current source inverter has
simple commutation circuit.
A. True B. False
Answer: Option A
Explanation:
No answer description
available for this question. Let
us discuss.
View
Answer Workspace Report Discuss
in Forum
47. In load commutated chopper, the commutating element
A. is capacitor
Answer: Option A
Explanation:
A. 2f
B. f
C. 0.5 f
D. 0.25 f
Answer: Option B
Explanation:
49. Assertion (A): A transistor has lower voltage drop during conduction as
compared to thyristor
Answer: Option C
Explanation:
50. Assertion (A): Typical value of thermal resistance from source to sink
of an SCR is about 0.3° C/W
Answer: Option B