Professional Documents
Culture Documents
Operator's Manual
Operator's Manual
MANUAL
,, Safety
HOURS: IVIon.- Fri. 8 a.m. to 5 p.m. (CT)
,, Assembly
,, Operation
WARNING ADVERTENCIA ,,Maintenance
Before using this product, read this Antes de utiiizar el producto, lea este
manual and follow all Safety Rules manual y siga todas las Reglas de ,,Parts
and Operating Instructions. Seguridad e Instrucciones de Uso.
,, EspaNol,p. 18
* This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association
(PWMA) standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
* Esta limpiadora a presiOn est_ clasificada conforme a la norma PWI01-2010 (comprobaciOn y clasificaciOn de rendimiento de limpiadoras
a presiOn) de la AsociaciOn de fabricantes de bombas a presiOn (Pressure Washer Manufacturers Association, PWMA).
For warranty coverage details to obtain free replacement, visit the web page: www.craftsman.com/warranty
This warranty does not cover spray guns, hoses, nozzle extensions, nozzles, spray tips or filters, which are expendableparts
that can wear out from normal use within the warranty period.
This warranty is void if this product is ever used while providing commercial services or if rented to another person.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
© 2013
SAVE THESE INSTRUCTIONS
_, WARNING Riskof electrocution.Contactingboth power
Read this manual carefully and becomefamiliar ///_\ conductors,at the sametime could causeelectric
with your pressurewasher. Knowits applications, shock or burn resulting in deathor serious injury.
its limitations, and any hazards involved.
• inspect cord before each use, DO NOTuse if cord is
important Safety information damaged.
• The product is equipped with a ground fault circuit
Safety Symbols and Meanings interrupter (GFCI)built into the power cord plug. If
A replacementof the plug or cord is required, use only
identical replacementparts.
e Keepall connections dry and off the ground.
ReadManual ElectricalShock Fire
e DONOTtouch plug with wet hands.
e DONOT run cord through doorways, windows, holes in
ceilings, wails, or floors.
e DONOTwalk on cord.
e DONOT drive over, drag or place objects over cord.
Slippery Surface Fall Fluid Injection
e DONOT spray near power source.
®
®
®
®
A - Fold Down Handle -- Handle folds down for space J - TurboSpray Tip -- Whirls a powerful pin-point jet of
saving storage. water for intense cleaning.
B - Spray Gun -- Controls the application of water onto K - Electric Cord with GFCI-- Theelectric pressure washer
cleaning surface with trigger device. Includes trigger lock. and operator is protected by a ground fault circuit
C - Plastic Wand -- Allows you to switch between three interrupter (GFCI).
different spray tips. L - Water Supply Inlet -- Connectto water supply using a
D - Handle Lock Bar -- Slides side to side; to lock handle in 50 ft. (15.24 m) maximum garden hose.
place and unlock to fold handle down. M- Spray Tips -- White tipped spray tip for general soap
E - DetergentTank -- Use to hold up to one quart (0.95 I) applications. Orangetipped spray tip is for various high
of PerfectMixTM detergent in tank. pressure applications.
F - Warning Labels -- Identifieshazards to be avoided when N - High PressureHose-- Connect one end to high
using your pressure washer. pressure water outlet and the other end to spray gun.
G - Nigh Pressure Water Outlet -- Connection for high P - Master ON/OFFToggle Switch -- Push top of switch in
pressure hose. (I) to turn pressure washer ON. Push bottom of switch in
(0) to turn pressure washer OFF.
H- Identification Label -- Provides model and serial
number of pressure washer. Pleasehave these readily
available if calling for assistance.
Your electric pressure washer requires some assembly but is ASSEMBLINGPRESSUREWASHER
quickly ready for use.
Your Craftsman pressure washer will need assembly before
If you have any problemswith the assembly of your operation:
pressurewasher, please caii the pressurewasher heJpJine
at 1=800-222-3136. 1. Fill out and send in registration card.
2. Lubricate o-rings.
UNPACKTHEPRESSUREWASHER 3. Connect pressure hose to spray gun and pump.
Become familiar with each piece before assembling the 1. inspect and clean connecting surfaces prior to lubrication
pressure washer, identify all contents with the illustration and assembly.
on page 5. If any parts are missing or damaged, call the 2. Use lubricants sparingly during assembly; a light film is
pressure washer helpline at 1-800-222-3136. all that is required.
3. Use a small brush or cotton swab to apply grease directly
to o-rings where they are not accessible (QCfitting, M22
fitting).
ConnectHosesand Water Supply ConnectWand and Spray Tip
1. Turn ONwater, point gun in a safe direction, press trigger
NOTICE Use ONLYcold water (less than 100°F).
lock button (H), then squeezetrigger (J) to purge pump
1. Attach garden hose (50 ft. / 15.24 m maximum) to water system and spray gun of air and impurities.
supply.
. Run water through garden hose for 30 seconds to flush
the hose of debris. Turn off water.
3. Confirm that water inlet screen (A) is installed in water
inlet located on left side from front of unit; Do Not
remove except for cleaning.
2. Insert and twist plasticwand (K) into spray gun (N). Once
wand slides into gun, applyfurther inwardpressure to
wand and twist 1/4 turn clockwiseuntil securelyin place.
NOTICE DO NOT run the pump without the water supply 3. Turn OFFwater and releasetrigger. Point gun in a safe
connected and turned on. direction and make sure trigger cannot be squeezed.
• Damageto equipment resulting from failure to follow 4. insert the spray tip (N) into plastic wand (P). Once spray
this instruction will void warranty. tip slides into gun, apply further inward pressure until it
. Attach opposite end of garden hose (B) to the water inlet SNAPSinto place.
coupling (C). Tighten by hand.
5. Attach high pressure hose (D) to the unit's water outlet
(E) located on right side from front of unit. Tighten by
hand.
_A cordcouldcause
electric
shock
or burnresulting The electric pressure washer motor runs only when the
(//_;, in death or serious injury. trigger is engaged.To stop the electric pressure washer and
turn off the motor:
• DO NOTuse an extension cord with this electric pressure
washer. Your home's electrical circuit receptacleor 1. Releasespray gun trigger.
extension cord may not provide lifesaving ground-fault 2. Press the master ON/OFFswitch to the OFF(0) position.
circuit-interruption protection.
NOTICE Releasingthe trigger will shut off the motor but
. Plug electrical power cord into an electrical circuit rated does not shut off electrical power to the unit.
for 120 Volts AC at 15 Amps that is properly installed
in accordancewith all local codes and ordinances. The 3. Turn off water supply.
indicator light on the GFCIshould be ON. 4. ALWAYS point spray gun in a safe direction and squeeze
spray gun trigger to relieve built up pressure in the unit.
_ its underlying
quipment tissues,could
produces resulting in serious
cut through injury
skin and
...........................
and possible amputation.
Spray gun traps high water pressure, even when motor is
stopped and water is disconnected, which could result in
serious injury.
• Keep high pressure hose connected to pump and spray
NOTICE The indicator light must be ON for the electric gun while system is pressurized.
3ressure washer to operate.
• ALWAYS point spray gun in safe direction, squeeze
WARNING Risk of electrocution. Non-operating ground spray gun trigger to releasehigh pressure, every time
you turn off pressure washer.
j_ death or serious
fault circuit injury.(GFCI)could
interrupter If indicator light does
result in not
, . stay ONafter test and reset, do not use GFCI. 5. Disconnect GFCIplug from outlet and coil power cord.
6. Coil and store high pressure hose, spray gun and
8. Press TEST button (B). The indicator light (C) should be accessories on the unit.
OFF.
There are three spray tips supplied with the pressure washer. 7. Start the pressure washer as instructed in How to Start
Your Electric Pressure Washer.
The turbo spray tip whirls a powerful pin-point jet of water
for intense cleaning. The white tipped spray tip is for general 8. Apply detergent to a dry surface, starting at lower portion
soap applications and the orange tipped spray tip is for of area to be washed and work upward using long, even,
overlapping strokes.
various high pressure applications.
9. Allow detergent to "soak in" for 3-5 minutes before
Usage Tips washing and rinsing. Reappiy as needed to prevent
* For most effective cleaning, keep spray tip from 8 to surface from drying. To prevent streaking, do not allow
24 inches away from cleaning surface. detergent to dry on surface.
* If you get spray tip too close, especially using a high ElectricPressure Washer Rinsing
pressure setting, you may damage surface being
1. Removewhite tipped spray tip from wand.
cleaned.
2. Install orange tipped spray tip.
Do Not get closer than 6 inches when cleaning tires.
3. Keepspray gun a safe distance from area you plan to
Applying Detergent spray.
A _ Chemicalscould cause burns resulting in /,_\ Spray gun could kickback causing you to fall
death or serious injury. /_, resulting in death or serious injury.
• Alwayswear indirect vented (chemical splash) safety Operatethe electric pressure washer from a
goggles marked to comply with ANSi 787.1 when using stable surface.
chemicals. Be extremely careful if you must use the electric pressure
• DONOTsubstitute safety glasses or dry-condition washer from a ladder, scaffolding, or any other similar
goggles for indirect vented safety goggles. location.
• DO NOT use caustic liquid with electric pressure washer. • Firmly grasp spray gun with both hands when using
• Use ONLYpressure washer safe detergents/soaps. power spray modes to avoid injury when spray gun kicks
back.
Follow all manufacturers instructions.
4. Apply a high pressure spray to a small area and then
To apply detergent, follow these steps:
check surface for damage, if no damage is found, you can
1. Review use of spray tips in How to Use Spray Tips. assume it is okay to continue rinsing.
2. Tip unit back and remove detergent tank cap. 5. Start at top of area to be rinsed, working down with same
3. Fill tank with PerfectMixTM concentrate solution. overlapping strokes as you used for cleaning.
10
PRODUCTSPECIFICATIONS OWNER'SRESPONSIBILITIES
PressureWasher Specifications GeneralRecommendations
Max Outlet Pressure .............. 1700 PSl@l.0 GPM* Regular maintenancewill improve the performance and
Max Flow Rate ................... 1000 PS1@1.3GPM* extend the life of the pressure washer.
Detergent Mix ................. See MFR's Instructions The pressure washer warranty does not cover items that have
Water Supply Temperature.... Not to exceed IO0°F (38°C) been subjected to operator abuse or negligence. To receive
Motor ........................ Universal (brush) Type full value from the warranty, the operator must maintain
pressure washer as instructed in this manual including
Rated Voltage .......................... 120 Volts AC
proper storage as detailed in Storage.
Current ................................. 12.5 Amps
Before EachUse
* This pressure washer is rated in accordanceto the 1. Cleandebris.
Pressure Washer Manufacturers Association (PWMA) 2. Check water inlet screen for debris or damage.
standard PW101-2010 (Testing and Rating Performance of 3. Check high pressure hose for leaks.
Pressure Washers).
4. Check spray gun operation.
PRESSUREWASHERMAINTENANCE
Clean Debris
11
Check High Pressure Hose 3. ALWAYS point spray gun in a safe direction, press trigger
lock button and squeeze spray gun trigger to release
The high pressure hose can develop leaks from wear, retained high water pressure.
kinking, or abuse. Inspect the hose each time before using it.
Checkfor cuts, leaks, abrasions or bulging of cover, damage ,_. WARNING The high pressure stream of water that this
or movement of couplings. If any of these conditions exist, JA,, equipment produces could cut through skin and
replace the hose immediately. its underlying tissues, resulting in serious injury
:J
"_/---_._}and possible amputation.
WARNING The high pressure stream of water that this Spray gun traps high water pressure, even when motor is
stopped and water is disconnected, which could result in
its underlying tissues,could
resulting in serious injury serious injury.
_ equipment produces cut through skin and
and possible amputation. * Keep high pressure hose connected to pump and spray
* NEVERrepair high pressure hose. Replace it. gun while system is pressurized.
* Replacement hose rating MUST equal or exceed * ALWAYS point spray gun in safe direction, squeeze
maximum pressure rating of unit. spray gun trigger to releasehigh pressure, every time
you turn off pressure washer.
Check SprayGun 4. Removespray tip from end of plastic wand.
Examine the hose connection to the spray gun and make sure 5. Use a small paper clip to free any foreign material
it is secure. Test the trigger (A) by pressing the trigger lock clogging or restricting any of the spray tips.
button (B) and making sure the trigger "springs back" into
place when you releaseit. You should not be able to press
the trigger without pressing the trigger lock button. Replace
spray gun immediately if it fails any of these tests.
12
AFTEREACHUSE Protecting the Pump
Water should not remain in the unit for long periods of
To protect the pump from damage caused by mineral
time. Sediments or minerals can deposit on pump parts and deposits or freezing, use PumpSaver, Model 74403, to treat
"freeze" pump action. Follow these procedures after every pump. This prevents freeze damageand lubricates plunger
use: and seals.
1. Press the master ON/OFFswitch to the OFF(0) position.
Remove power cord plug from electrical outlet. NOTICE PumpSaver is available as an optional accessory, it
2. Turn off water supply, point gun in a safe direction, press is not included with the electric pressure washer. Contact the
trigger lock button and squeezetrigger to relieve trapped nearest authorized service center to purchase Pump Saver.
pressure.
3. Disconnect garden hose from the water supply and the
electric pressure washer. NOTICE You must protect your unit from freezing
4. Disconnect hose from spray gun and high pressure outlet temperatures.
on pump. Drain water from hose, gun, and wand. Use a * Failureto do so will permanently damageyour pump
rag to wipe off the hose. and render your unit inoperable.
5. Drain water from pump by tipping unit on its right side * Freezedamage is not covered under warranty.
(water inlet facing down).
6. Coil power cord and store on back of unit.
7. Store unit in a clean, dry area. To use PumpSaver, make sure the electric pressure washer
8. If storing for more than 30 days see Winter or Long Term is turned off and inlet and outlet hoses are disconnected.
Storage on next page. Readand follow all instructions and warnings given on the
PumpSaver container.
NOTICE Water left in the pump could freeze and damage the
pump.
13
ProbJern Cause Correction
1. Water inlet is blocked. 1. Clear inlet.
2. inadequatewater supply. 2. Provide adequatewater flow.
3. Garden hose is kinked or leaking. 3. Straighten garden hose or replace if
Pump has following problems:failure leaking.
to producepressure, erratic pressure, 4. Cloggedwater inlet screen. 4. Checkand clean water inlet screen.
chattering, loss of pressure, low water 5. Water supply is over IO0°F (38°C). 5. Provide cooler water supply.
voJurne. 6. High pressure hose is blocked or 6. Clear blocks in high pressure hose
leaks. or replace hose.
7. Spray tip is obstructed. 7. Cleanspray tip.
8. Pump is faulty. 8. Contact Sears service facility.
1. Water supply is not turned on. 1. Turn on water supply.
2. Unit is not turned on. 2. Press the master ON/OFFswitch to
Unit fails to start when spray gun the Pressure Washer ON position
trigger is squeezed. (I). ResetGFCI.
3. Garden hose is too long. 3. Use only 50 ft. (15.24 m) maximum
garden hose.
Detergent faiJsto mix with spray. 1. High pressure spray tip installed. 1. Replacewith white tipped spray tip.
14
CRAFTSMAN1700 PSi ElectricPressure Washer 580.750290
ExplodedView and Parts List
1 m
/
8
12
t
15
16
17
i CRIIFTSr4 lIH i
Product questions or problems?
-33t -45
Customer Care ot Line
Get answers to questions, troubleshoot problems,
order parts, or schedule repair service.
Para respuestas a preguntas o problemas, y ordenar
piezas o pedir servicio para la reparaci6n de su equipo.
To help us help you, register your product at www.craftsman.com/registration
www.craftsman.com/signup
Como miembro exdusivo, recibe diversos beneficios como ofertas, precios especiales, proyectos
nuevos, consejos de expertos y nuestro programa de puntos SHOP YOUR WAY REWARDS!
® Registered Trademark / TMTrademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
® Marca Registrada / TMMarca de F&brica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros paises