Professional Documents
Culture Documents
Axia Iq Aoip Mixing Console: Specifications
Axia Iq Aoip Mixing Console: Specifications
Axia Iq Aoip Mixing Console: Specifications
SPECIFICATIONS: loop
Frequency Response
8 - 24 Channel Digital Console
Any input to any output: +0.5 / -0.5 dB, 20 Hz to 20 kHz
Flexible AoIP Design
4 x Mic Inputs Dynamic Range
16 x Stereo Analogue Inputs Analog Input to Analog Output: 102 dB referenced to 0 dBFS, 105 dB
2 x Digital Input / Output “A” weighted to 0 dBFS
8 x Output Busses Analog Input to Digital Output: 105 dB referenced to 0 dBFS
Compatible With The Axia Livewire Range Digital Input to Analog Output: 103 dB referenced to 0 dBFS, 106 dB
“A” weighted
QOR.32 Connections Digital Input to Digital Output: 125 dB
Microphone Inputs: 4x balanced XLR-F, with selectable Phantom
power Equivalent Input Noise
Analog Inputs: 16x RJ-45, StudioHub+ standard. Microphone Preamp: -128 dBu, 150 Ohm source, reference -50 dBu
Analog Outputs: 8x RJ-45, StudioHub+ standard. input level
AES/EBU Inputs: 2x RJ-45, StudioHub+ standard.
AES/EBU Outputs: 2x RJ-45, StudioHub+ standard. Total Harmonic Distortion + Noise
GPIO: 8x DB-15 Mic Pre Input to Analog Line Output: <0.005%, 1 kHz, -38 dBu input,
Livewire: 4x 100Base-T with PoE, RJ-45, 2x 100Base-T, RJ-45, 2x +18 dBu output
1000Base-T, RJ-45, 2x Gigabit, SFP (Small Form Pluggable) Analog Input to Analog Output: <0.008%, 1 kHz, +18 dBu input, +18
Console Frame Connections: 3x, 6-pin “latch and lock” style dBu output
Accessory Connections: 1x, 6-pin “latch and lock” style Digital Input to Digital Output: <0.0003%, 1 kHz, -20 dBFS
Digital Input to Analog Output: <0.005%, 1 kHz, -6 dBFS input, +18
Microphone Preamplifiers dBu output
Source Impedance: 150 Ohms
Input Impedance: 4 k Ohms minimum, balanced Crosstalk Isolation, Stereo Separation And CMRR
Nominal Level Range: Adjustable, -75 dBu to -20 dBu Analog Line channel to channel isolation: 90 dB isolation minimum, 20
Input Headroom: >20 dB above nominal input Hz to 20 kHz
Output Level: +4 dBu, nominal Microphone channel to channel isolation: 80 dB isolation minimum, 20
Hz to 20 kHz
Analog Line Inputs Analog Line Stereo separation: 85 dB isolation minimum, 20Hz to 20
Input Impedance: 20 k Ohms kHz
Nominal Level Range: Selectable, +4 dBu or -10dBv Analog Line Input CMRR: >50 dB, 20 Hz to 20 kHz
Input Headroom: 20 dB above nominal input Microphone Input CMRR: >50 dB, 20 Hz to 20 kHz
SPECIFICATIONS:
FM SECTION
Tuning Range 87.5 - 108 Mhz
External antenna FM 75 Ohm (Ground isolator included)
Frequency range 20 Hz - 15 kHz
Usable sensitivity 10 dBf
S/N ratio: Mono/Stereo 76 dB / 70 dB
THD: Mono/Stereo 0.5% / 0.7%
AM SECTION
Tuning Range 520 - 1710 Khz
External antenna AM antenna (included)
Frequency range 30 Hz - 11 kHz
Usable sensitivity 10 mV
Signal to noise ratio 50 dB
Total Harmonic Distortion (THD) 1%
GENERAL
Output RCA Cinch
Output level Adjustable (FM: 900 mV / AM: 500 mV)
Power supply 230V
Remote control IR (included) / Wired via contacts on Euroblock
Dimensions (H x W x D) 44 x 483 x 280 mm
Weight 3.1 Kg
NAUTEI NX15 AM Transmitter
130% positive peak modulation to 16.5
kW
AC INPUT:
Voltage:
340 V to 510 V, 3 phase or to
customer
Specifications
Power Consumption:
17.9 kW typical at 15 kW, 0%
modulation
26.8 kW typical at 15 kW, 100%
modulation
General:
Transmitter Type Cos (theta):
Medium wave, AM, 100% solid state Built in Dynamic Carrier Control
0.95 typical
SPECIFICATIONS:
Earthquake resistance: 8
Wrapped ice: 8°
Verticality: 1/1000