Professional Documents
Culture Documents
M60dsa4 1445X Ext Man 001
M60dsa4 1445X Ext Man 001
M60DSA4-1445X-EXT
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 2 of 9
REVISION HISTORY
CHANGE DESCRIPTION
01 Initial Release
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 3 of 9
TABLE OF CONTENTS
1.0 FEATURES
2.0 SERVICE
3.0 SPECIFICATIONS
5.0 DISASSEMBLY/ASSEMBLY
M60DSA4-1445X-EXT
4.06” 10K SIDE DOOR STRIPPER PACKER
Reference Drawing M60DSA4-1445X-EXT-ART-001
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 4 of 9
M60DSA4-1445X-EXT
4.06" 10,000 PSI "DSA4" SIDE DOOR STRIPPER PACKER
1.0 FEATURES
The Texas Oil Tools DSA4 Side Door Stripper Packer is designed to pack-off on coiled tubing as it is
stripped in and out of the well, at working pressures up to 10,000 psi. This design permits the
replacement of the packing elements and bushings through the open "window" below the injector.
Changing packers is always easier, but it is particularly advantageous when changing packers with
tubing in the well.
The side door design permits replacement of the packer, energizer and non-extrusion rings by
hydraulically retracting the pack-off piston and exposing an open portal through which these elements
may be changed with tubing in the well. This design also incorporates positioning the balanced
actuator piston above the pack-off element, isolating the hydraulic chamber from well pressure and
eliminating any effects caused by fluctuations in well pressure.
The hydraulic pack-off cylinder is long stroke and double acting. This double acting feature allows the
operator to use hydraulic pressure to pump the piston up to relieve pack-off pressure on the packer
system; as well as, to completely retract it, exposing the packers for easy replacement.
The DSA4 packers, energizers and non-extrusion rings are common to the DS84 and DTS4 model
stripper packers. Internal wear bushings, packers, and non-extrusion rings are available for coiled
tubing sizes up to 2 7/8" size and all alloy components in contact with pressurized well fluids conform
to NACE Specification MR-01-75 for H2S Service.
2.0 SERVICE
H2S SERVICE - All well fluid wetted alloy components to NACE MR-01-75, with Viton and Poly-Myte
seals. Hydraulic seals are Nitrile. Operating temperature range -20°F. to +200°F. Note: seals and
pack- off elements are available for higher temperatures.
DNV -32°C H2S SERVICE - All well fluid wetted alloy components to NACE MR-01-75, with Viton and
Poly-Myte seals. Hydraulic seals are Nitrile. Operating temperature range -32°C.(-25°F.) to +93°C.
(+200°F.) Charpy Impact Tests and NDE on all parts required by DNV, complete with DNV Design
Verification, Data Book and Certificate of Conformity for operating to -32°C.
ARCTIC -50°F H2S SERVICE - All well fluid wetted alloy components to NACE MR-01-75, with low
temperature o-rings and special Poly-Myte seals. Charpy Impact Tests at -50°F and NDE on all parts
required by API 6A. Operating temperature range -50°F. to +200°F.
HYDRAULIC REQUIREMENTS:
The DSA4 hydraulic cylinder has a larger diameter than the standard DS84 stripper packer, since
placing the hydraulic system above the packer requires that the pack-off force exceed the force of the
well pressure acting on the packer. The ratio of the well pressure to hydraulic pressure is dependent
upon the size of the coiled tubing.
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 5 of 9
Example: 1.75" coiled tubing, 4,000 psi well pressure 4000/2.20= 1818 PSI hydraulic pressure
The calculated hydraulic pressure is the pressure required to overcome the force of the well pressure. A
slight additional amount of hydraulic pressure will be required to compress the packer.
To operate the DSA4 in all of the various applications, the hydraulic system should have a 5,000 psi
working pressure. Most applications will require much less pressure. Retract pressure on the lower side of
the piston should not exceed 5,000 psi. The DSA4 works most conveniently with a pump having a 4-way
valve and two hoses. If a single hose system is used, be sure that the quick connectors do not have check
valves as this would prevent escape of the downstream hydraulic fluid and prevent operation of the tool.
3.0 SPECIFICATIONS
Hydraulic Pressure
Pack-Off .............................................................................................. 500 psi min/ 5,000 psi max.
Retract ................................................................................................. 500 psi min/ 5,000 psi max.
Hydraulic Volumes
Pack-Off ............................................................................................................................... 554 in3
Retract ................................................................................................................................. 155 in3
Torque #/FT
Union Nut ....................................................................................................................... Hand Tight
L.H. Lock Collar.............................................................................................................. Hand Tight
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 6 of 9
PREMATURE PACKER WEAR - The internal wear bushings above the packers are extra long, for
better centering of the coiled tubing and longer wear life. The single most frequent cause of
premature packer wear or failure, is worn bushings. At very low well and hydraulic pressures, worn
bushings may be useable. At higher pressures, it is essential that the non-extrusion rings and
packer bushings fit closely around the tubing to prevent packer extrusion. Bushings must be
replaced frequently to minimize any extrusion gaps.
PACKER REPLACEMENT - Close BOP pipe rams to control well pressure and vent residual well
pressure that may remain between the DSA4 stripper and the BOP. Back out the two lock screws
(2-1) and open wide both doors (2). Pressure up the retract port and fully retract piston (22) exposing
packers and seal (1-11). Remove upper non-extrusion ring (12) while supporting packer bushing (29).
Remove both halves of energizer (13) to expose packer (14). Remove packer, lower non-extrusion
ring (12) and packer bushing (29). Inspect packer bushing and lower bushing (28) for wear and seal
for damage. Replace as necessary.
A reserve seal (1-11), located in the lower groove on the seal sub (16) may be used during operations
with tubing in the well.
Re-install lower bushing and lower non-extrusion ring. Install packer bushing into piston and
support while installing new packer, energizer and upper non-extrusion ring. Pressure up on upper
pack-off port and extend piston down over pack-off and seal until doors can be closed around piston
above step ring (23). Rotate the lock screws to the locked position. Pressurize upper pack-off port to
energize packer as necessary. Equalize well pressure above the rams in the BOP and open
rams.
ASSEMBLY - Reverse above Disassembly Procedure in same sequence and complete second
portion of Packer Replacement Procedure.
A bushing installation tool (11) is available to aid in installing the interlocking bushings.
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 7 of 9
M60DSA4-1445X-EXT
4.06” 10K SIDE DOOR STRIPPER PACKER
Reference Drawing M60DSA4-1445X-EXT-ART-001
ARCTIC -50°F
ITEM DESCRIPTION QTY H2S SERVICE
SERVICE
1 SEAL KIT 1 M60DSA4-SK03 M60DSA4-SK03B
2 DOOR ASSY 2 9109-0440 9109-0440
3 BUSHING EXT ASSY 1 DSA4-SB44Y DSA4-SB44Y
4 SHCS .500 13UNC X 2.00 2 7947-0808 7947-0808
5 PLUG SKT #8 1 7934-0208 7934-0208
6 ADAPTER #8 SAE 1 7934-0518 7934-0518
7 PLUG .250 NPT 1 7934-1002 7934-1002
8 PLUG .500 NPT 2 7934-1004 7934-1004
9 SHCS .250 20UNC X .750 8 7935-0403 7935-0403
10 SHCS 1.00 8UNC X 4.50 8 7935-1618 7935-1618
11 BUSHING INSTALL TOOL 1 7940-1121 7940-1121
12 NON EXTRUSION RING 2 8412-2444 8412-2444
13 ENERGIZER 1 8412-3750 8412-3750
14 PACKER INTERLOCK 1 8412-6044 8412-6044
15 LOCKING COLLAR 1 8807-2621B 8807-2621B
16 SEAL SUB 1 9109-0422XB 9109-0422XB
17 BOTTOM PLATE 1 9109-0421B 9109-0421B
18 TIE ROD 1 9109-0431S 9109-0431S
19 FLANGE MOUNT 1 9109-0432B 9109-0432B
20 HYDRAULIC CYLINDER 1 9109-0433B 9109-0433B
21 BUSHING SLEEVE 1 9109-0321B 9109-0321B
22 PACKER PISTON 1 9109-0435B 9109-0435B
23 STEP RING 1 9003-0436B 9003-0436B
24 WASHER 1 9003-0437B 9003-0437B
25 BOTTOM SUB 1 9109-3445B 9109-3445B
26 BODY 1 9109-0450B 9109-0450B
27 UNION NUT 1 9221-0940B 9221-0940B
28 LOWER BUSHING 1 9109-0544 9109-0544
29 PACKER BUSHING 1 9109-0644 9109-0644
30 GUIDE BUSHING 2 9109-2144 9109-2144
31 BOTTOM SPACER 1 9109-2244 9109-2244
32 THREAD PROTECTOR 1 8002-0362 8002-0362
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 8 of 9
M60DSA4-SK03*
SEAL KIT 4.06” 10K SIDE DOOR STRIPPER PACKER
Reference Drawing M60DSA4-1445X-EXT-ART-001
M60DSA4-SK03 M60DSA4-SK03B
ITEM DESCRIPTION QTY
H2S SERVICE ARCTIC -50°F
1-1 O-RING NITRILE 1 7813-3351 7813-A351
1-2 SEAL URETHANE 1 2003-1221 2003-1221B
1-3 O-RING NITRILE 1 7813-3378 7813-A378
1-4 O-RING VITON 1 7813-4433 7813-A433
1-5 PISTON SEAL 1 7951-3A16 7951-3A16
1-6 O-RING VITON 1 7813-4908 7813-A908
1-7 SEAL POLYMYTE DEEP B 1 7821-4752 7821-4752B
1-8 SEAL POLYMYTE TYPE B 1 7821-5252 7821-5252B
1-9 RETAINER RING EXTERNAL 2 7824-0847 7824-0847
1-10 RETAINER RING EXTERNAL 1 7824-8007 7824-8007
1-11 SEAL VITON 2 7973-5502 7973-5502
1-12 BACK-UP RING 1 7992-1644 7992-1644
9109-0440
DOOR ASSEMBLY 4.06” 10K SIDE DOOR STRIPPER PACKER
Reference Drawing M60DSA4-1445X-EXT-ART-001
ARCTIC -50°F
ITEM DESCRIPTION QTY H2S SERVICE
SERVICE
2-1 LOCK SCREW 1 9003-0447 9003-0447
2-2 HINGE 2 9003-0448 9003-0448
DSA4-SB44Y
BUSHING EXT ASSY 4.06” 10K SIDE DOOR STRIPPER PACKER
Reference Drawing M60DSA4-1445X-EXT-ART-001
ARCTIC -50°F
ITEM DESCRIPTION QTY H2S SERVICE
SERVICE
3-1 TOP BUSHING 1 M601009727-44 M601009727-44
3-2 CAP 1 9705-1943 9705-1943
3-3 GUIDE BUSHING 1 9109-2144 9109-2144
3-4 SHCS 2 7947-0808 7947-0808
www.nov.com
M60DSA4-1445X-EXT-MAN-001
Rev / 01
P a g e | 9 of 9
M60DSA4-1445X-EXT-ART-001
www.nov.com