Professional Documents
Culture Documents
Info RASCHIG Pall-Ring-350 PDF
Info RASCHIG Pall-Ring-350 PDF
Subject page
Materials 4-5
The weights for PALL-Rings made of other metal alloys are obtained by
multiplication with the following factors:
Aluminium 0.35
Monel and nickel 1.13
Copper 1.14
Brass 1.09
Titanium 0.6
Hastelloy 1.3
1
Operational data for
PALL-Rings made of special
stoneware/porcelain
2
Operational data PALL-Rings
made of plastics
3
PALL-RING
Materials
PALL Rings are made of three main groups of materials:
Metals
Mainly carbon steel and alloyed chrome-nickel steels. Special alloys
such as Hastelloy, Incoloy, Monel titanium and zirconium are being
used more and more frequently, and are also processed.
Ceramics
The most frequently processed materials are special stoneware and
special hard porcelain. These ceramic materials are densely sintered,
they have great resistance to high temperatures and a uniform material
structure.
Plastics
Most of the production of thermoplastics consists of polypropylene
grades in various versions. In addition to polyethylene, high-
performance plastics are also used. As a standard procedure, Raschig
uses virgin materials. Regenerates are only processed upon special
request.
Depending on the stress caused by temperature and chemical attack,
the following quality grades of polypropylene must be distinguished:
standard polypropylene (PP)
or permanent temperatures of up to approx. 70 °C (158 °F).
heat-endurance stabilised polypropylene (LTHA)
for permanent operating temperatures of up to 110 °C (230 °F).
Under permanent thermal stress, this specially stabilised material has
approximately twice the service life of normally stabilised
polypropylene.
4
PALL-RING
5
Compensation for the
"decrease in volume" for
dumped packings
12
10
Allowance (%)
The values indicated in the tables for dumped packings are valid for a
diameter ratio vessel: packing size of D : d = 20.
Since the arrangement of the packings is less compact near the vessel
wall than in the interior of the bed, the number of packings per cubic
meter increases with the diameter ratio.
The opposite diagram shows by which "allowance" the theoretically
calculated vessel volume for diameter ratios of more than 20 must be
increased in order to completely fill the space required.
If the plastic or metal packings are, for instance, thrown into the column,
this may result in a further decrease in volume due to abnormally
compact packing.
D = diameter of the vessel to be filled
d = diameter or nominal size of the packings
6
Generally applicable pressure
drop diagram for tower
packings
Optimum results with packed columns can only be obtained with well-
designed liquid distributors, support grids and hold-down grids!
Please note that this diagram no longer applies in case of foaming
liquids.
1,0
0,1
500 be obtained with well-
300 designed liquid distributors,
0,04 200 support grids and hold-
0,03 down grids!
0,02 100
⋅
Please note that this
0,01
50 diagram no longer applies
in case of foaming liquids.
0,004
0,003
20
0,002
0,001
0,01 0,02 0,1 0,2 1,0 2,0 10
1/2
(L/G)⋅[ρG/(ρL-ρG)]
7
Tower packing factor
Table 1
Table 2
8
Tower packing factor
The graph shown on page 3 that is valid for all types of tower
packings and for mass system or operating conditions as well as
Table 1 showing the tower packing factors are based on a
Sherwood correlation postulated in 1938, which has been updated
regularly with the level of engineering valid at the time.
Table 1 shows the tower packing factors F in [1/m] that constitute
an important characteristic parameter , seeing that the square root
of the tower packing factors is inversely proportional to the gas flow
rate of the packed bed.
This correlation can clearly be seen by taking the example of 50
mm PALL Rings made of metal with a tower packing factor of 66
and 2" = 50 mm TORUS SADDLES made of ceramics with a tower
packing factor of 130. The tower packing factors show that the gas
flow rate for metal PALL Rings is 40 percent higher than for the
TORUS SADDLES.
GPall Rings 130
= = 1,4
GTorus Saddles 66
Thorough tests have shown that the tower packing factors
indicated in Table 1 cannot be seen at constant values, but rather
that they change within a certain range, depending on the load of
the liquid or gas. The types of tower packings which show the
highest pressure drop, such as RASCHIG RINGS, also tend to
change most with respect to their tower packing factor.
The tower packing factors in Table 1 can be consulted for planning
columns. This results in column diameters that are somewhat
overdimensioned, especially in case of large flow rates of liquid
and particularly when RASCHIG RINGS are used.
Table 2 shows that the fluctuation range of the tower packing
factors F for four different types of tower packings in the most
common sizes as a function of the abscissa value of the generally
applicable pressure drop diagram.
12
L⎛ ρ ⎞
X = ⎜⎜ G ⎟⎟
G ⎝ ρL − ρ G ⎠
9
Pressure drop with metal
PALL-RINGS
mixture air / water
PALL-RING 25 mm PALL-RING 38 mm
3000 3000
100
125
100
uL= uL=
75
50
25
10
75
50
25
10
0
0
1000 1000
700 700
600 600
500 500
Spec. Pressure drop Δp/H (Pa/m)
400 400
300 300
200 200
100 100
70 70
60 60
50 50
40 40
30 30
20 20
10
Pressure drop with metal
PALL-RINGS
mixture air / water
PALL-RING 50 mm PALL-RING 80 mm
3000 3000
uL=
75
50
25
10
125
100
uL=
75
50
25
10
0
1000 1000
700 700
600 600
500 500
Spec. Pressure drop Δp/H (Pa/m)
400 400
300 300
200 200
100 100
70 70
60 60
50 50
40 40
30 30
20 20
11
Pressure drop with ceramic
PALL-RINGS
mixture air / water
PALL-RING 25 mm PALL-RING 35 mm
3000 3000
75
50
25
10
uL=
0
50
40
30
20
10
uL=
0
1000 1000
700 700
600 600
500 500
Spec. Pressure drop Δp/H (Pa/m)
400 400
300 300
200 200
100 100
70 70
60 60
50 50
40 40
30 30
20 20
12
Pressure drop with ceramic
PALL-RINGS
mixture air / water
PALL-RING 50 mm
3000
100
uL=
75
50
25
10
0
1000
700
600
500
Spec. Pressure drop Δp/H (Pa/m)
400
300
200
100
70
60
50
40
30
20
13
Pressure drop with polypropylene
PALL-RINGS
mixture air / water
PALL-RING 15 mm PALL-RING 25 mm
3000 3000
125
100
125
100
uL= uL=
75
50
25
10
75
50
25
10
0
0
1000 1000
700 700
600 600
500 500
Spec. Pressure drop Δp/H (Pa/m)
400 400
300 300
200 200
100 100
70 70
60 60
50 50
40 40
30 30
20 20
14
Pressure drop with polypropylene
PALL-RINGS
mixture air / water
PALL-RING 35 mm PALL-RING 50 mm
3000 3000
uL=
75
50
25
10
150
125
100
uL=
75
50
25
10
0
1000 1000
700 700
600 600
500 500
Spec. Pressure drop Δp/H (Pa/m)
400 400
300 300
200 200
100 100
70 70
60 60
50 50
40 40
30 30
20 20
15
Pressure drop with polypropylene
PALL-RINGS
mixture air / water
PALL-RING 90 mm
3000
125
100
uL=
75
50
25
10
0
1000
700
600
500
Spec. Pressure drop Δp/H (Pa/m)
400
300
200
100
70
60
50
40
30
20
16
Liquid hold-up in columns with metal
PALL-RINGS
400
50 1700
40 800
30
0
20
3 2
Liquid velocity uL (m /m h)
400
50 Δp=
40 1600
800
30 400
0
20
3 2
Liquid velocity uL (m /m h)
17
Liquid hold-up in columns with metal
PALL-RINGS
400
50
40
30
Δp=
20 1600
800
400
0
Pall® Ring 38 mm in Metal
10
3 4 5 10 20 30 40 50 100 200 300
3 2
Liquid velocity uL (m /m h)
400
300
Pall® Ring 50 mm in Metal PALL-RING 50 mm
200
Diameter of column: approx.750 mm
Liquid hold-up (l/m3)
50
40
30
Δp=
20
800
400
0
10
3 4 5 10 20 30 40 50 100 200 300
3 2
Liquid velocity uL (m /m h)
18
Absorption of CO2 into NaOH for
Vol. Mass transfer coefficient kG⋅a (1/s) metal and plastic PALL-RINGS
1,0
PALL-RING 25 mm
0,5
0,4
Diameter of column: 760 mm
0,3
Packing height: 3 m
0,2 Gas rate: 2200 kg/m3h
Gas concentration: 1% (mean value)
Liquid concentration: 4 % NaOH
0,1
Liquid temperature: 24 °C (75 °F)
0,05
0,04
Pall® Ring 25 mm
0,03
0,02
3 4 5 10 20 30 40 50 100 200 300
3 2
Liquid velocity uL (m /m h)
Vol. Mass transfer coefficient kG⋅a (1/s)
1,0
PALL-RING 38 mm
0,5
0,4
Diameter of column: 760 mm
0,3
Packing height: 3 m
0,2 Gas rate: 2200 kg/m3h
Gas concentration: 1% (mean value)
Liquid concentration: 4 % NaOH
0,1
Liquid temperature: 24 °C (75 °F)
0,05
0,04
0,03
Pall® Ring 38 mm
0,02
3 4 5 10 20 30 40 50 100 200 300
3 2
Liquid velocity uL (m /m h)
19
Absorption of CO2 into NaOH for
Vol. Mass transfer coefficient kG⋅a (1/s) metal and plastic PALL-RINGS
1,0
PALL-RING 50 mm
0,5
0,4
Diameter of column: 760 mm
0,3
Packing height: 3 m
0,2 Gas rate: 2200 kg/m3h
Gas concentration: 1% (mean value)
Liquid concentration: 4 % NaOH
0,1
Liquid temperature: 24 °C (75 °F)
0,05
0,04
Pall® Ring 50 mm
0,03
0,02
3 4 5 10 20 30 40 50 100 200 300
3 2
Liquid velocity uL (m /m h)
Vol. Mass transfer coefficient kG⋅a (1/s)
1,0
PALL-RING 80/90 mm
0,5
0,4 Diameter of column: 760 mm
0,3 Packing height for 80 mm of metal: 3 m
Packing height for 90 mm of metal: 2,3 m
0,2
Gas rate: 2200 kg/m3h
Gas concentration: 1% (mean value)
0,1 Liquid concentration: 4 % NaOH
Liquid temperature: 24 °C (75 °F)
0,05
0,04
0,03
Pall® Ring 80/90 mm
0,02
3 4 5 10 20 30 40 50 100 200 300
3 2
Liquid velocity uL (m /m h)
20