TOSHIBA, ELECTRONIC G2 D 9097247 cous 3
ELECTRONIC
O2E 16008
5.8W AUDIO POWER AMPLIFIER
CAR STEREO CAR RADIO AUDIO OUTPUT
Very Few External Parts (Require 4 PCS Capacitor)
+ Adjustable Closed-Loop Cain
1 High sustaining Over Voltage
(Surge voltage up to 40V for 0.2eec. pin 1 to 8)
+ Excellent Ripple Rejection
High Power and Low Distortion
Poures.88(TyP.) at Voc
mHD-0.22(typ.)
Possible to Use for 20 Load :
PouT=9.38CIyP.) at Ve
+ Operating Supply Voltage
{ Audio Moting Cireute
1 Protection Circuit (for Load short, Excessive
Supply Voltage and Thermal shut-down)
-2V, Ry=4O, THD=10% «
eum.
gazes
MAXINUN RATINGS (Ta=25°C) MOLD q
cascrmustic | snow | earaoa:] owe vastly Et
Teak Supply Voltage @O0m«) Woo owrse| 40 |v oe 4
D.€ Supply Voltage vee) | 25 |v
Operating Supply Voltage | Vocope)| 18 | V_[tyanac ee
sion (Te=25°C)| Pp 12.5 Ww
Operaiing Tnperature Pope] a0~75 |e
Storage Temperature Tata | -55~150| °c
ELECTRICAL CHARACTERISTICS .
(Umees sthervine specitied, Vcgr12.5V, RLeAD, Ry°6000, fotke, tar25°C)
rear
cin
Quiescent Current Tecq | - + ~ = 40} 80 | aa
ocsiee 45 [100
~ /THD=10% ~ [5.2] ~
uaeput Power ror | [reoria.20 me so [sep | w
feria Het |. Toa | =
Tviacs batput Porer Por [= Jvoots.2v, Vartooar | = [0 = pw
Pour=1W = fo2pis
cat Hernonte vistoreion | mao | [Rovi=i00a sesso] x
Yolzage Gaia wat = is | 33 es | a
‘Input Resistance RIN - = = Mf Ko
CaEpur Boise Voltage Wao | = [egeionas Bieso~ zoe | -[o.s [a0] aw
—65—
see ee AUDIO LINEAR IC:TOSHIBA, ELECTRONIC O2 Dd [9097247 Soueso9 5 If
TA7222AP
T-74-05-01
BLOCK DIAGRAM AND TEST CIRCUIT
FIo-1 owns ouFrLy
om Aa
nosons iow
* te
at & oxo
pe j 7
fe
5g
1, Terminal D 4s snout. stage GND, terminal @ in output stage GND.
2. Closed-Loop voltage gain of the anplifier ie determined by the ratio ; (RI+R2)/RL>
TA72224P 4g fixed at typically 53.0 dB for designing minimua external components.
+ When higher closed loop gain is desired, the gain can be increased by connecting
a resistor between pin @ and pin @. Open loop gain 4s obtained by shortening
pin @ and pin@ «
+ When lover closed loop gain is desired, the following two ways can be used.
A. Series connecting a resistor and a capacitor between pin ® and pin @ «
BL Series adding a resistor to pin @
Both A and B, lover closed loop gain than 40 dB is not recommended. And ale:
ejection ratio is decreased by using B configuration in such ac
capacitor from pin @ to ground 18 recommended.
(Fig.2,3,4 show these waye.)
3. For applications requiring high ripple rejection ratio, an excellent supply
voltage ripple rejection is obtained by connecting @ capacitor (recommended
value 4.78) between pin @ and ground.
(R,R-£ shows these characteristics)
ripple
fe, connecting
‘Terminal @ {8 Audio Muting Control Input.
+ When control input is low state (; open or below 0.3V), muting circuit does not
operate, OFF.
= When control input ie high
ON. (Refer to Fig.5)
above 1.0V), muting efreuit, then, operates,TOSHIBA, ELECTRONIC O2 D 097247 cowso 1
O2E 16910 Dd
~TAT2220P
T-74-05-01 J
HIGHER CLOSED LOOP GAIN CIRCUIT LOWER CLOSED LOOP GAIN CIRCUIT (A)
APPLICATION CIRCUIT
FIe-2 BIe-3
LOWER CLOSED LOOP GAIN CIRCUIT (8) __AUDTO MUTING CIRCUIT
Hote : Capacitor 2-7 must be Note + Power output reduction level
tuned when high ripple HOME at RyeDkO
rejection ratio de &
requested. 3548 at Rge0
ICs Fre-s,
Se AUDIO LINEAR IG==
67