Professional Documents
Culture Documents
Plts78dub User Manual PDF
Plts78dub User Manual PDF
Plts78dub User Manual PDF
7'' Single DIN In-Dash Detachable Motorized Touch Screen TFT/LCD Monitor
w/ DVD/CD/MP3/MP4/USB/SD/AM-FM Bluetooth A2DP & AVRCP compatible
USER MANUAL
To ensure safety while driving
-1-
Precaution
ON INSTALLATION
DO NOT install any receiver in locations where;
- it may obstruct the steering wheel and gearshift lever operations, as this
may result in a traffic accident.
- it may obstruct the operation of safety devices such as air bags, as this
may result in a fatal accident.
- it may obstruct visibility.
DO NOT operate any receiver while manipulating the steering wheel, as
this may result in a traffic accident.
The driver must not watch the monitor while driving.
IF THE DRIVER watches the monitor while driving, it may lead to
carelessness and cause an accident.
IF YOU NEED to operate the receive while driving, be sure to look ahead
carefully or you may be involved in a traffic accident.
IF THE PARKING BRAKE is not engaged.“ ParkingBrake” flashes on the
monitor, and no playback picture will be shown.
- This warning appears only when the parking brake wire is connected to
the parking brake system built in the car ( refer to the electric connection)
NOTES ON CLEANING
-Clean the LCD panel with a slightly damp soft cloth.
-Do not use solvents such as benzine, thinner, commercially available
cleaners or antistatic spray .
- Do not use alcohol to clean the screen .
If your car was parked in a cold or hot place, the picture may not be clear .
The monitor is not damaged . The picture will become clear the temper-
ature in your car becomes normal .
-2-
Safety Information
CAUTION:
WARNING:
This Digital Video Player is designed and manufactured to respond to the Region
Management Information that is recorded on a Digital Video disc. If the Region
number described on the Digital Video disc does not correspond to the Region
number of this Digital Video Player, this Digital Video Player cannot play this disc.
-3-
Disc Note
Disc formats supported by this unusable) depending on your handle it
player and conditions in the usage environment.
Note these scratches are not an
Digital Digital Audio and Video
Disc size 12 cm
indication of any problem with the player.
Video Video
Audio and Video Label side
VCD VCD up
Disc size 12 cm
Audio
CD CD
Disc size 12 cm Do not touch
the
Audio underside
MP3 MP3 of the disc
Disc size 12 cm
Do not
bend
Discs which cannot be played
with this player
Digital Video-RAM
CDV Wipe the disc from
center
CDG toward the outside
edge
Handling and Cleaning
Dirt, dust, scratches and warping disc Preparing New Discs with Rough
will cause misoperation. Spots
Do not place stickers or make A new disc may have rough edges on
scratches on discs. its inside and outside edges. If a disc
Do not warp discs. with rough edges is used, the proper
A disc should always be kept in its setting will not be performed and the
case when not in use to prevent from player will not play the disc. Therefore,
damaging. remove the rough edges in advance
Do not place discs in the following by using a ball point pen or pencil as
places: shown on the right. To remove the
1.Direct sunlight rough edges, press the s i d e o f t h e pen
2.Dirty, dusty and damp areas or pencil against the inside and outside
3.Near car heaters edges of the disc.
4.On the seats or dashboard Rough spots
on
outside edge
Disc Cleaning
Use a dry soft cloth to wipe the surface.
Ball point pen
If the disc is quite dirty, use a soft cloth or pencil
Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
Install the unit where it does not get in the driver ' s way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
30
Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, from the heater, or where it would be
subject to dust, dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from "Front"(conventional DIN
Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded
screw holes at the sides of the unit chassis). For details, refer to the following
illustrated installation methods.
-5-
Installation
Installating the unit
DASH BOARD
METAL MOUNTING
HEX NUT STRAP
SPRING WASHER
PLAIN WASHER CONSOLE
TAPPING SCREW
SLIDE BRACKET
HOUSING
HEX BOLT
SCREWDRIVER
TABS
KEY PLATE
KEY PLATE
If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, first remove
the PLASTIC TRIM OUT of the both sides away, then insert the two KEY PLATE into
left and right side of chassis as above illustration.
-6-
Installation
How To Remove And Install The Front Panel
When detaching or attaching the control panel, be careful not to damage the
connectors on the back of the control panel and on the panel holder.
REL button
1 2
2). Put the front panel in the protective case for safe keeping.
protective case
-7-
Installation
ATTACHING THE FRONT PANEL
1). First, insert the left side of the front panel into the main unit(SEE 1 ).
(Note: the “Hollow ” point on the front panel must be attached into the “Bulge”
point of the unit . )
2). Gently push the right-down hand side of the front panel until you feel a “ Click” .
(SEE 2 )
Bulge
Hollow
1
2
Precautions
Do not touch the contacts on the front panel or the unit body, since this may
result in poor electrical contact. If dirt or dust accumulates on the contacts ,
wipe them with a clean, dry cloth .
-8-
Electric Connection
WIRING CONNECTION
ISO CONNECTOR
PINK (B+)12V
IGNITION SWITCH(B+)
RED REAR CAMERA SWITCH
BROWN
YELLOW CHOKE (B-)PARKING BRAKE
MEMORY BACK-UP(B+) BOX BLUE
BLACK AUTO ANTENNA
GROUND(B-)
WHITE GREY
FRONT FRONT
LCH SPK. WHITE/BLACK GREY/BLACK RCH SPK.
Note:
the earth connection cable (parking brake B-) must be connected in order for
pictures to be played back to the monitor. If the cable has not been correctly
connected, the message “PARKING BRAKE” appears on the monitor.
-9-
Remote Control
18 A/PS
VOL TOP RPT INT 12
1 2 3
11 VOL RDM
4 5 6 27
AF
10 SEL 7 8 9
TA 26
4 SETUP GOTO +10 0 25
8
-11-
Remote Control
Ref # Button Function
This button is used to confirm selections and settings within many
23 ENTER of the menus in the OSD system.
Note :
The lithium cell in the battery compartment of remote control has been secured for
transport with a foil . Before initial use please remove this foil so that the remote
control is ready for operation .
-12-
Basic Operation
POWER ON/OFF
Touch the “OFF” ICON on screen
to turn the unit off . Press the“ ”
onthe front panel to turn It on, FIG.2
press it again to turn off .
LOADING/EJECTING A DISC
Loading a Disc
1. Press the POWER ( ) button on the Adjusting the viewing angle .
front pane to turn the device on . When the monitor does not move, you
press button on the panel to turn
2. Insert the disc with printed side facing the monitor upward or downward at
up into the disc slot (1) . fine steps to get a desired viewing
3. The player starts playback the disc angle .
automatically .
1 2
FIG.3
Ejecting a Disc
In disc mode, Press the (2) button on
the front panel to eject the disc . Do not rotate the monitor forcibly to
avoid mechanical damage .
-13-
Basic Operation
When the monitor turns downward to Touch the “SET” ICON on touch screen
a certain angle, it will draw in . to enter the setting mode, the message
will display like following :
FIG.6 BRIGHTNESS
CONTRAST
COLOR
TFT Monitor Adjustment 15
In Radio mode, touch the“ RADIO ”
icon or In media mode , touch the
range to enter the home menu,
the message like following as below. Note: the RDS icon displays only when
setting EUR FREQ and power off the unit
(1) (2) and then power on again.
Touch “SYSTEM” on the setting menu,
touch the “ / ” ICONS to select the
adjustment item, touch the “ / ”
ICONS to adjust the selectment item, it
depends on your habit to setup the data.
ADJUSTABLE ITEMS:
BRIGHT: 0 to 32
Adjust if the picture is too bright or
too dark.
(3) (4) (5) (6)
CONTRAST: 0 to 32
Adjust the contrast of the bright and dark
(1). SET button portion.
touch to enter the SETTING mode .
(2). OFF (Power) button COLOR: 0 to 32
Adjust the color for the picture-lighter or
in any modes, touch the “ OFF ” ICON darker.
to switch the unit off .
TINT: 0 to 32
(3). Button Adjust the tint if the human skin color is
Touch to close the monitor . unnatural.
(4). Button -Adjustable when “NTSC “ is selected for
“NTSC/PAL “ .
Touch to eject the disc form the
disc slot. ANIMATION
(5). Button In RADIO mode, you can change the
to adjust the angle of monitor down- playing time of animation among of
ward until your desired angle . “OFF, 10S, 30S, 1M,1.5M, 2M, 3M and 4M ”.
Note:
(6). Button Please set the playing time of the ani-
to adjust the angle of the monitor mation to “ 10S ” for the first, when you
upward until your desired angle . turn the unit on .
-14-
Basic Operation
SETTING WALLPAPER BALANCE: R 0-10 to L 0-10 .
in wallpaper mode, you can select the Adjust sound balance between left
among of “AUTO, GREEN, YELLOW, RED, and right speakers .
LIGHT BLUE, BLUE, PINK ” .
When you select the “AUTO” item, the FADE: F 0-10 to R 0-10
player will change the background Adjust sound balance between front and
automatically . rear speakers .
SETTING LED LIGHT (3 COLORS)
In LED COLOR mode, you can select the SUB-WOOFER: ON or OFF
color among of “Auto, Blue, Red, Pink ” . LOUDNESS: ON or OFF
When you select the “AUTO” item, the
player will change the panel color RADIO LOC: LOC or DX
illumination automatically .
BT ON/OFF
RADIO STEREO: STEREO or MONO
Touch to switch the BT BUZZER: ON or OFF
function ON and OFF .
HOUR
MINUTE
TREBLE 24H/12H
BASS 11:36 AM
+06
Note: the RDS icon displays only when Note: the RDS icon displays only when
setting EUR FREQ and power off the unit setting EUR FREQ and power off the unit
and then power on again. and then power on again.
Touch the “ SOUND ” section on the
setting menu, touch the “ / ” ICONS Touch the “ TIME ” section on the setting
to select the adjustment item, touch the menu, touch the “ / ” ICONS to
“ / ” ICONS to adjust the selectment select the adjustment item, touch the
item , It depends on your habit to select “ / ” ICONS to adjust the selectment
the Audio mode . Then touch the “SET” item, then touch “ SET ” icon to confirm.
icon to return to the previous playback . It`s depend on your need to setup
the data.
ADJUSTABLE ITEMS:
ADJUSTABLE ITEMS:
TREBLE: -7to +7
Adjust treble level . Hour adjustment: 0-23
Minutes adjustment: 0-59
BASS: -7 to +7
Adjust bass level . Time format selectment : 24H/12H
-15-
Basic Operation
Setting Audio Mode Rear View Camera
In any modes, touch the “EQ” range on When connecting the rear view camera
the touch screen (or press the EQ button the mirror image of the rear view is auto-
on remote control) to select one of matically displayed on the monitor
the preset sound modes: ROCK/POP/ when you change the gear to the back
JAZZ/CLASSIC/USER . position.
(Note: additional monitor can not display
EX.: In RADIO mode the image.)
FM1
87.50 MHZ
DX ST USER ALTERNATE AUDIO SOURCE
On the front panel of the unit , there is an
AUX IN jack, to connect analogue replay
devices. Use this jack to replay sound of
other replay equipment such as
1 88.50 2 90.00 3 98.00
Digital Video players, computers, etc.
4 106.00 5 103.00 6 80.50 Via the loudspeakers.
1). Please f ollowing the diagram below,
The information will display in the connect the external device with stereo
monitor as follow : jack plug the AUX IN socket .
2). Press the MOD button to select the
ROCK USER JAZZ AUX IN connection.
3). Use the buttons on the external
device itself to operate it .
POP CLASSIC
RESET
The RESET button is to be activated for
the following reasons:
A. Initial installation of the unit when
all wiring is completed.
B. All the function buttons do not operate.
C. Error symbol on the display.
-16-
Control Panel
UNIT KEYS
11
4
9
OPEN
MIC
VOL-
/CH1~6
8
VOL+
MODE
TA/AF MU/PTY
7
PAIR
IR USB IN AUX IN
PUSH SEL BND
1 2 18 12 13 14 15 3 10 5 6
Control Panel
16 17
Front Face of Chassis after remo ving Control Panel
1. OPEN or BUTTON
To slide the monitor out and stand it up or into the monitor slot, press this button;
In media or BT MUSIC mode, pressing |<< or >>| button can play previous or
next track; continuously and long pressing |<< or >>| button can fast backwards
or forwards at the following multiple of normal speed: x2, x4, x8, x20, x1.
In BT PHONE mode, for the function of the and buttons, please refer to
the part of the BT Operation.
5. TA/AF BUTTON
TA Function [traffic Announcement] Button(for Rds Only)
In RADIO mode
When you swing briefly the MU/PTY knob in the direction of the TA/AF button ,
the TA function is activated, the TA symbol appears in the display .
(swing it again to turn off . )
AF [Alternative Frequencies]
Swing and hold (more than 2’s) the MU/PTY knob in the TA/AF direction , the AF
function is activated. The AF symbol appears in the display . (swing and hold it
again to cancel this function .) The function about RDS to see page 23 .
Note: In Radio mode, press and hold the SEL knob for a long time to access the
selection menu: REG ON/REG OFF, PI MUTE/PI SOUND, AF ON/AF OFF .
Repeatedly pressing the SEL knob to select the item and by using the VOL+/- to
change .
6. PAIR/BND BUTTON
In Radio mode, press it repeatedly to select the desired radio band: FM1, FM2,
Fm3, AM1(MW1), AM2(MW2) .
In BT PHONE mode, for the function of the PAIR button, please refer to the part
of the BT Operation.
7. MU/PTY BUTTON
Press it button to switch of the loudspeakers for a short period. The word MUTE
flashes in the display. Press it again to cancel the mute function. This function
can also be cancelled by rotating the VOL multifunction button.
In Radio Mode, press this button and hold for a bout 2 seconds to select the PYT
of the grogram type (examples of such types of program are : NEWS, POP.....)
-18-
Control Panel
B) In Radio Mode
Press this button repeatedly to preset station. With this system a total of 30
stations can be stored in the memory . Each band store up to six preset
stations. The stations might be FM1, FM2, FM3, AM1 (MW1) and AM2
(MW2) band.
Follow the instructions below:
-Store in Memory
> Select the frequency band
> Press repeatedly the button to select the desired memory key .
> Select the station
> Keep the desired memory key pressed in until the station is heard again
after a brief interruption .
- Retrieve a preset station
press the button repeatedly to retrieve a station which had been stored in the
memory in advance the chose number is shown on display .
9. REL BUTTON
Press it to detach the control panel.
12. IR sensor
AM2(MW2) AM1(MW1) DX
When an FM stereo broadcast is Note: the RDS icon displays only when
hard to receive setting EUR FREQ and power off the unit
Press ST/MO button on the remote and then power on again.
control to select the MONO or STEREO Touch the “ SOUND ” section on the
mode . (When Stereo mode is activated, setting menu, touch the “ / ” ranges
the ST symbol will appear . ) to select the “ Radio L/D ” item, touch the
“ / ” ranges to choose between the
LOC and DX mode of Local and Long-
distance traffic news .
-20-
Touch Screen Operation
Storing and Listening to a Automatic Preset Setup
Memory station In Radio Mode, touch and keep (for more
than 2 ’ S) the screen of “ APS ” range to
Setting Memory active automatic station storage.
The radio searches within the current
FM1
87.50 MHZ frequency band, e.g. FM1, for the stron-
DX ST USER ger signal level until the search cycle
has finished . The six strongest stations
are then allocated to the corresponding
storage locations .
Then the station of the first storage
1 88.50 2 90.00 3 98.00
location is set .
Scan Function
4 106.00 5 103.00 6 80.50
In Radio mode, briefly touch the “APS”
section on the touch screen , the radio
With this system, a total of 30 stations briefly plays all the preset stations of the
can be stored in the memory of six frequency band .
buttons. Each band stores up to six
preset stations. The stations might be RDS FUNCTION
FM1, FM2, FM3, AM1(MW1), and
AM2(MW2) band. In Radio mode, touch the “RADIO” ICON
The operation is as below : to enter the main menu, then touch the
- Store in Memory “ SET ” ICON to enter the set mode, the
>Select the frequency band message in the display : (only in the
>Select the station “TA ON” mode. )
>Keep the desired memory key pressed
in until the station is heard again after
a brief interruption .
- Retrieve a preset station
Touch the 1-6 ranges briefly to retrieve
a station which had been stored in the REGION
memory in advance the chose number PI SOUND/MUTE
is shown on display .
ON
-21-
Touch Screen Operation
ADJUSTABLE ITEMS: TA Traffic Announcement
(Priority For Traffic Information)
REGION SET
Touch to switch the REGION function In Radio mode, touch the cursor button
ON and OFF . to switch the TA function ON and OFF .
When the TA function is activated, the
PI SET
TA symbol appears in the display .
Touch to change between PI MUTE and
During radio operation in one FM
PI SOUND .
frequency band the search for a traffic
announcement station is started
REG FUNCTION automatically (TA SEEK) .
at certain times some stations divide up If an FM station is being received which
their programs into regional programs transmits the latest traffic announce-
with varying content . ments from time to time, the TP display
REG ON : the message “REG ON” will lights up.
appears in the display for a few seconds .
Note : When the TA function is switched on ,
- the display capacity is limited . It is the FM traffic automatically interrupt
possible that in the double display mode CD operation (the word TRAFFIC
some segments of the display are appears in the display).
deleted .
- the function REG ON prevents the The volume level is increased to the
radio from switching to alternative minimum value for the transmission of
frequency which have a diferent regional traffic announcements.
program content .
REG OFF : the program identification After the traffic announcements has
(PI) of the regional program is ignored finished, the program that was previo-
during the search for an alternative usly running is resumed.
frequency (AF) or a program Interruption of the TA Function:
identification (PI) . if you would like to interrupt the current
traffic announcement, touch the TA
PI MUTE / PI SOUND section on screen briefly . This does
(only for radio operation) switch off the TA mode .
if you are in an area where two program
identifications (PI) overlap, you can AF FUNCTION
select the option PI SOUND and PI MUTE (Alternative Frequencies)
for playback of the sound. Alternate In Radio mode, touch the cursor button
switching of the program identification to switch the AF function ON and OFF .
should be avoided .
AF is a function that works with the help
PI SOUND : of RDS (Radio Data System) and can
if switching nevertheless occurs the only be used with FM stations . The radio
sound of another station is heard for searches in the background for the best
less than one second . frequency reception of the station that
has been tuned into .
PI MUTE :
the sound of another station is
suppressed .
-22-
Touch Screen Operation
Touch the AF section on touch screen or With PTY function you can specifically
swing and keep the SEL knob in the select stations transmitting a particular
TA/AF direction for about 2 seconds , type of program. Touch the PTY range
the AF function is activated. The AF on screen repeatedly to call up the PTY
symbol appears in the display . selection menu . The message
“PTY SEEK” then appears briefly in the
When the AF function has been switched display .
on, the radio continuously tests the
signal strength of the AF frequency . When PTY has been selected the radio
The test interval for each AF frequency starts searching for corresponding PTY
depends on the signal strength of the information and stops when the PTY
current station and varies from a few information has been found, “NO PTY”
minutes in the case of weak signals. appears in the display. If the PTY
Whenever the new AF frequency is information being searched for no longer
stronger than the station that is currently exists, the PTY function automatically
tuned in , the radio switched to this switches to normal mode .
frequency for a short time for a short
time and the message
“NEW FREQUENCY “ is displayed for
one or two seconds.
Note :
the status of the AF function is shown by
an AF symbol in the display.
If the AF symbol appears in the display,
the AF function is switched on and RDS
transmission date is being received .
If the AF symbol flashes in the display,
the AF function is selected but no RDS
signal can be received at the moment .
PTY FUNCTION
In Radio mode, touch screen of “PTY”
range to select the Program type .
In Radio mode, touch screen of “PTY”
range to select the Program type .
-23-
Touch Screen Operation
Media Operation To search the disc with numbers
In any modes, repeatedly press MOD
button on front panel to enter the media
play mode .
The message will display as below :
(When Parking Brake is applied .)
MENU
To display the root menu on stored
Digital Video discs .
In Digital Video mode, touch to
TITLE
PBC
display the title menu. In VCD
mode, touch to switch the PBC
ON and PBC OFF.
To show/hide the Subtitle
(depending on the media)
FOR VCD/CD :
Touch the screen of the “RPT” range
Skipping Track (or press longer the 2/RPT button on the
remote control) to select REPEAT mode
During DISC playback, touch as follows :
/ to skip to next/back one REPEAT ONE REPEAT ALL
track.
REPEAT OFF
FOR MP3 :
Note : Touch the screen of the “RPT” range
For some VCD2.0 disc (PBC-playback (or press longer the 2/RPT button on the
control), above these buttons may be remote control) to select REPEAT mode
unavailable. as follows :
REP EAT ONE REP EAT FO LD ER (or DIR)
-26-
Touch Screen Operation
ON-SCREEN DISPLAY FUNCTION 2.Example for VCD/SVCD/CD:
OSD During playback, touch the A.Touch or Press OSD for first time:
screen of the OSD section,
it will display the following VCD TRK 1/19 PBC A C 0:01:36
as below :
E.Touch or Press OSD for fifth time: B.Touch or Press OSD for second time:
F. Touch or Press OSD for sixth time: C. Touch or Press OSD for third time:
The message on the screen will be The message on the screen will be
cleared. cleared.
-27-
Touch Screen Operation
Digital Video Special Function
1. Multi-subtitle Language
3. Title Menu Function
Function (for Digital Video Only)
For Digital Video:
During Digital Video playback. If the Digital Video has multiple titles
Touch the SUBTITLE section recorded on the disc. It can select
on touch screen(or press the preferred title from the title menu to start
SUBTITLE on the remote) . playback.
Each time the button is pressed or touch, - During Digital Video playback, press
number of the subtitle language changes TITLE button on the remote .The title
in sequential order. menu is display.
- Select preferred title by the cursor
Notes: button and confirmed by press the
- The language number is different ENTER button .
according to the disc.
- Some discs only contain one subtitle
language. For VCD:
- When no different subtitle language Press TITLE/PBC button on the remote
are recorded, “ INVALID KEY ” will be control while the disc is playing, you can
switch between "PBC ON"and "PBC off"
displayed at screen left top corner.
mode.
For VCD/CD:
during playback, touch the AUDIO
section of the touch screen or Press
AUDIO on the remote . It is possible to
switch the sound between monaural
and stereo sound.
MONO LEFT MONO RIGHT MIX-MONO
STEREO
-28-
Touch Screen Operation
MEDIA SETUP MENU SYSTEM SETUP
EXIT
TV TYPE SETUP
This player is capable of playing discs
1. IN disc model Touch the screen of recorded in either PAL or NTSC formats.
Make the selection based on whether you
“ ” range or press the SETUP button
are connecting the unit to a PAL TV or an
on remote . NTSC TV. You can also set the unit to
2.The SETUP menu is displayed. AUTO (autoselect). The disadvantage to
3.Touch directly the desired item to autoselect is that each time you turn the
select the preferred item . unit on it checks to see what kind of
monitor is connected, which causes a
Or by using the / / / buttons . small delay and some flickering of the
4. Touch the EXIT section to clear the display image which you may find
setup menu or press the SETUP on the unpleasant.
remote control .
Overview Of The Main Menu
SYSTEM SETUP
TV SYSTEM ON
SCREEN SAVER OFF
( 1) (2) ( 3) (4) TV TYPE
PASSWORD
(1). System Settings RATING
DEFAULT
(2). Language Settings
(3). Video Settings EXIT
(4). Digital Settings
SCREEN SAVER SETUP
If the screen displays a static image for
too long, some "burn-in" may occur,
leaving a permanent trace of the image
behind. To avoid this, turn ON the
SCREENSAVER item. After a short
period of inactivity on the monitor, the
unit will substitute a moving image to
avoid burn-in.
-29-
Touch Screen Operation
EXIT EXIT
TV DISPLAY SETUP
This is to select the appropriate TV SYSTEM SETUP
aspect (4:3 or 16:9) according to the 1 KID SAFE
TV SYSTEM
connected TV set. 2 G
SCREEN SAVER 3 PG
Normal/PS (For 4:3 TV) TV TYPE 4 PG13
Played back in the PAN & SCAN style. PASSWORD 5 PG-R
(If connected to wide-screen TV, the RATING 6 R
7 NC-17
left and right edges are cut off.) DEFAULT
8 ADULT
Normal/LB (For 4:3 TV) EXIT
Played back in LETTER BOX style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the RATING
Select suitable parental guidance with
screen.) the cursor buttons and confirm it by
Wide (For 16:9 TV) pressing the ENTER button.
Select when a wide-screen TV set is
connected.
-30-
Touch Screen Operation
LANGUAGE SETUP
LANGUAGE SETUP
LANGUAGE SETUP ENGLISH
OSD LANGUAGE
ENGLISH AUDIO LANG GERMAN
OSD LANGUAGE
GERMAN SUBTITLE LANG SPANISH
AUDIO LANG
SPANISH MENU LANG FRENCH
SUBTITLE LANG
FRENCH PORTUGUESE
MENU LANG
PORTUGUESE ITALIAN
ITALIAN RUSSIAN
RUSSIAN OFF
EXIT EXIT
-31-
Touch Screen Operation
VIDEO SETUP
VIDEO SETUP
these settings allow you to set the video
signal brightness, contrast, hue, and BRIGHTNESS +6
saturation . CONTRAST
+4
+2
HUE 0
SATURATION -2
-4
VIDEO SETUP SHARPNESS
-6
BRIGHTNESS 12
10
CONTRAST EXIT
8
HUE 6
SATURATION 4
2
SHARPNESS HUE- the hue of the video signal (the
0
color of the pictures) .
EXIT
-32-
Touch Screen Operation
DIGITAL SETUP
VIDEO SETUP
BRIGHTNESS 12
DIGITAL SETUP
10
CONTRAST 8
HUE 6 FULL
SATURATION 4 6/8
DYNAMIC RANGE
2 4/8
SHARPNESS
0 2/8
OFF
EXIT
EXIT
SATURATION- the saturation of the
video signal (the vividness of the color)
all above can be adjusted to your DYNAMIC RANGE CONTROL
tasters . Select DRC and adjust the dynamic
range of a Dolby Digital encoded
program. There are 8 steps between
full compression and off compression.
VIDEO SETUP
BRIGHTNESS 8
6
CONTRAST
4
HUE
2
SATURATION 0
SHARPNESS
EXIT
-33-
Touch Screen Operation
AUX Operation
On the front panel of this unit, there is an
AUX IN jack, follow the diagram below to
connect analogue replay devices(only
for the Audio connect, if you want to
connect the Video, please plug the RCA
<Video input > on the back of the unit .) .
Use this jack to replay sound of other
replay equipment such as media players,
computers, etc. Via the loudspeakers.
AUX IN
4). Touch the volume+/- sections on
touch screen or use the VOL+/- on
the panel to adjust the volume level.
Ground
Right
Left
-34-
Touch Screen Operation
BT OPERATION IMPORTANT:
1). If the pairing can not be completed
1. “Pair” To Your BT Phone within approximately 2 minutes ,
Prior to using the BC-HF-V01 for the fist whiles the pairing mode is activated,
time, you must pair it with a BT-enabled and you will need to reattempt pairing
mobile handset. (See steps 2-5 above) .
The following steps describes pairing 2). After pairing is completed, if the BT
the instruction for a typical BT-enabled ICON is stilling flash on the TFT ,
mobile handset. please follow the steps to reattempt
pairing through your handset until the
BT ICON remains solid on the screen.
1). Place the BC-HF-V01 and mobile
handset in 3 meters apart.
CALL COME IN
Function
123561875 zone
Function
zone
Function
zone
Note:
END/REJECT A CALL 1). Before using the function of the BT
In BT menu, touch the screen of “ ” about the unit , please check your
range (or press briefly “REDIAL/ ” phone’s instruction guide or contact
button on remote control) . phone manufacture if you are not sure
if your phone supports the hands-free
BT function .
REDIAL LAST NUMBER 2). When operating the function of BT
In BT menu, touch “ ” range (or about the unit , you need make your
press longer “ REDIAL/ ” button on call-phone and the unit successfully
the remote control the “DIAL LAST CALL for one time. Afterwards, you only
/DIAL OUT NOW ” will display on the need to take on the power and the
TFT monitor . function of BT will work in three
minutes automatically if you want to
operate the function of BT .
ADJUST THE VOLUME
During conversation in progress, 3). If you want not to use the function of
tune the Volume switch until you reach the BT about the unit , you can select
the desired volume level. the BT OFF .
-36-
Touch Screen Operation
USB OPERATION
Following the diagram below, connect Changing From DISC to USB Playback
your USB device to the front panel Mode
USB port . If it is properly connected, If the disc present in the player is an
the device will be mounted and start Digital Video or VCD or MP3/WMA or
playing automatically. MP4 disc, touch the screen of the
“ ” range to enter the home menu,
then touch the “USB” ICON to enter
the USB mode .
USB IN
IMPORTANT NOTE:
To prevent damage to the USB device,
do not remove or disconnect it during
playback. it is also a good practice to
remove the USB drive during disc
playback.
-37-
Touch Screen Operation
SD/MMC card OPERATION
The unit can support playback MP3/WMA/JPEG/MP4 and Divx format which are
stored into SD and MMC memory card .
Please read below before you start the operation of memory card .
INSERTING THE SD OR MMC CARD .
Label side
facing upward
003
007 4 Select the play mode(JPEG).
008
Touch directly to select the play mode and then touch the desired track to play .
Or Use / / / on the remote control to select the play mode or item, then
press ENTER button on the remote control to confirm.
REPEAT FUNCTION
Touch the screen of “REPEAT ” range or press longer “REPEAT” on the remote
control repeatedly can select two kinds of repeat play mode.
REP-ONE:
Play the same song over and over again.
REP ALL:
Play all songs on the disc, then repeats the entire disc over and over again .
NOTE:
in JPEG/MPEG4 mode, the details operations as same as MP3/WMA operation .
-39-
Specification
Generall :
Supply Voltage: 12V DC (11V-15V)
Current Consumption: Less than10 A
Signal System: Compositive video 1.0Vp-p 75
Discs Played: (1)DIGITAL-VIDEO Disc
5"(12 cm) single-sided, single-layer
5"(12 cm) single-sided, double-layer
(2)Compact Disc (CD-DA, VIDEO CD)
5"(12cm) disc
RADIO Section:
For 2 Bands For 2 Bands
(Europe) (U.S.A.)
FM FM
Frequency Coverage: 87.5 to108 MHz 87.5 to107.9 MHz
IF: 10.7 MHz 10.7 MHz
Sensitivity (S/N = 30 dB): 15 dBu 15dBu
MW AM
Frequency Coverage: 522 to1620 KHz 530 to1710 KHz
IF: 450 KHz 450 KHz
Sensitivity (S/N = 20 dB): 40 dBu 40 dBu
TFT Monitor:
Monitor Screen Size: 7 Inch Wide
Color System: NTSC/PAL
BT:
B T specification: V1.2 Class 2
B T profile supported: Headset, Handsfree and A2DP & AVRCP profiles
Range of frequency: 2.4GHz Spectrum
NOTE:
Specification and design are subject to modification, without notice, due to
improvements in technology.
-40-
Troubleshooting
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
No color in picture The disc format is not Please choose a correct color
according to the TV-set system.
used (PAL/NTSC)
No JPEG files are recorded
JPEG disc can Change the disc
on the disc.
not be played
back JPEG files are not recorded Change the disc Record JPEG
in a compliant formant files using a compliant
application
The built-in microcomputer Press the RESET button.
The operation keys is not operating properly Front panel is not properly fixed
do not work due to noise into its place
The radio does not The antenna cable is not Insert the antenna cable firmly
work connected
The signals are too weak Select a station manually
-41-