Professional Documents
Culture Documents
DS81 (En)
DS81 (En)
__p Jumper Settings C9 VGA Connector C10 EDP Connector V1.0 C11 Battery connector
Front Panel F1. Mic-In Pin Assignments (CN25): Pin Assignments: Pin Assignments (CN1):
C1 Power Button (SW3) C2 USB Connector 1=GND 11=CRT_HSYNC_R 1=PANEL_VDD 21=NC 1=V_BAT 1
F2. Headphone 2=GND 12=GND 2=CAD_56B 22=D3+_56B_C 2=GND
Pin Assignments : 3=SDVO_CLK_D 13=GND 3=PANEL_VDD 23=GND
F5 F6 F7 F3. Power LED 1=GND 4=GND 14=GND 4=HPD_56B_C 24=GND
1 2 3 4
2=USB10P 5=SDVO_DATE_D 15=BOUT-O 5=PANEL_VDD 25=INV_PWR_SRC 40 39 C12 Clear CMOS&POWER BUTTON
6=GND 16=VGA_PWR 6=NC 26=D2-_56B_C
F4. HDD LED 3=USB10N
7=GND 17=GOUT-O 7=PANEL_VDD 27=INV_PWR_SRC Pin Assignments (SW2):
4=USBPW04 8=GND 18=VGA_PWR 8=NC 28=D2+_56B_C
F5. Power Button 1=RTCRST-
9=CRT_VSYNC_R 19=ROUT-O 9=PANEL_VDD 29=INV_PWR_SRC 2
2=+5V
SPK1 10=GND 20=VGA_PWR 10=NC 30=GND 1
C3 Fan Connector C4 3=GND
F6. Card reader 11=GND 31=INV_PWR_SRC
Pin Assignments (FAN1): Pin Assignments (CN1): 12=GND 32=D1-56B_C 4=PWRSW-
F7. USB2.0 Ports 1=GND 1=SPKR_OUT
13=EDP_BKLTCTL 33=INV_PWR_SRC
14=AUX-_56B_C 34=D1+56B_C 1
F1 F2 F3 F4 2=+12V 2=GND 2 20 15=EDP_BKLTEN 35=GND
2
3=SPEED_SENSE
C13 SATA POWER connector
16=AUX+_56B_C 36=GND
4=PWM_CTRL 17=GND 37=NC Pin Assignments (PW1):
4
18=GND 38=D0-_56B_C 1=GND 3
1 19 19=NC 39=NC
Back Panel B1. COM1 Port
1
2
3
20=D3-_56B_C 40=D0+_56B_C
2=GND
3=+5v
2
1
(RS232/RS422/RS485) 4 4=+5v
1=PULL AGND 2=LINE-R For safety reasons, please ensure that the power cord is discon-
B5. USB3.0 Ports 3=NC 4=LINE-L nected before opening the case. 5. Orientate the CPU and socket and please align the CPU notches with
the socket alignment keys. Make sure the CPU is perfectly horizontal,
B6. USB2.0 Ports 5=PULL AGND 6=FRONT_L
1. Unscrew the two screws of the chassis cover. insert it into the socket.
7=NC 8=FRONT_SENSE
B7. DisplayPort 9=PULL AGND 10=FRONT_R Latch Latch
11=BK_AUDIO-JD 12=MIC1_R
B8. HDMI Port 13=AGND 14=MIC1_L Notch on the CPU/ 5. Repeat the above steps to install additional memory modules, if required.
B3 B4 B5 B6 B7 B8 B9 Alignment Key of the
B9. Clear CMOS&POWER Socket CPU Socket
13 11 9 7 5 3 1
1150
CPU
D. Component Installation
BUTTON 2. Slide the cover backwards and upwards.
Triangle Pin1 1. Install the Mini PCIE card into the Mini PCIE slot and secure with
Marking on the CPU screw.
14 12 10 8 6 4 2
2
Please be aware of the CPU orientation, DO NOT force the CPU into
Left / Right Panel 1
the socket to avoid bending of pins on the socket and damage of CPU!
C6 COM PORT 6. Close the metal load plate, lower the CPU socket lever and lock in place.
7. Spread thermal paste evenly on the CPU surface.
Pin Assignments (COM1&COM2):
Kensington® Lock Port 1=DCD 2=RX 9 7 5 3 1
3=TX 4=DTR 3. Unfasten the rack mount screw and remove the rack.
5=GND 6=DSR Load lever Retention tab
7=RTS 8=CTS 2. Place the HDD in the rack and secure with the four screws from the side.
10 8 6 4 2
9=RI 10=NC Metal load plate
Thermal Paste
application area
EDP C10
4. Lift the metal load plate on the CPU socket. 1. Replace the cover and refasten the screws.
Safety Information 1
CN1 C11 Read the following precautions before setting up a Shuttle XPC.
2
CAUTION
Metal load plate 45-degree
Incorrectly replacing the battery may damage this computer. angle
Replace only with the same or equivalent as recommended by Shuttle. 2 . Complete.
DC IN LAN Ports USB3.0 USB2.0 Display HDMI C12 SW2
(x2) Ports (x2) Ports Port Port Dispose of used batteries according to the manufacturer's instructions.
Please load the optimized BIOS settings.
LThe product’s colour and specifications may vary from the actually shipping product. 53R-DS8103-2001