Professional Documents
Culture Documents
Renderoc MPR
Renderoc MPR
Uses Application
For application as either a high build internal or external The substrate should be prepared in such a manner as to
crack resistant plaster. provide a sound mechanical key. If so required, the
substrate may be primed with a rush coat made by mixing
sufficient water with a 25 kg bag of Renderoc MPR to
Advantages produce a thin slurry. The rush coat shall be applied at a
thickness of between 1 – 4 mm and allowed to set for 48
Internal shrinkage control mechanism. hours prior to the application of the plaster.
High build in single pass. To mix the plaster, charge a mechanical mixer with 3.5 –
3.75 litres of water per 25 kg bag of product and slowly add
the Renderoc MPR. Mixing shall continue for a minimum
May be hand or machine applied.
period of 3 minutes or any such longer period as required.
Alternatively a plaster mixer pump with automatic water
Permits a high quality finish to be obtained. feed may be employed.
Long life plastic packing. When mixed, Renderoc MPR may be applied to the
substrate either by pump or trowel as appropriate at a
Description thickness range of 4 - 8mm in single application. Renderoc
MPR may be finished using all conventional plastering tools
and finishing techniques.
Renderoc MPR is a pre-mixed sand/cement plaster material
which incorporates blended cements, lime, graded sands,
Curing
performance enhancing additives with shrinkage control
products.
Renderoc MPR, in common with all cementitious products,
should be cured immediately on completion of application
Specification using wet curing techniques. The applied plaster has to be
sprayed by clean water every 12 hours for 2 to 3 days
Where shown on the contract documents, the plaster shall be according to ambient conditions.
Renderoc MPR supplied by Fosroc. The cured product shall
have a crack free, water resistant and highly durable Cleaning
properties.
All tools and equipment shall be cleaned immediately after
use with water.
Properties
Preparation
Technical support
The substrate shall be made free of coatings, laitance, oil,
grease, dust or any other deleterious substances. Sufficient Fosroc offers a comprehensive technical support service to
clean water shall be sprayed on to the substrate to achieve a specifiers, end users and contractors. It is also able to offer
“saturated, surface dry” condition immediately prior to on-site technical assistance, an AutoCAD facility and
commencing application work. dedicated specification assistance in locations all over the
world.
Highly absorbent surfaces (aerated blocks, calcium silicate
blocks etc.) shall be primed with Nitobond SBR diluted with
water at a 1:1 ratio.
Page 1
Renderoc MPR
Estimating Additional information
The use of barrier creams to provide additional skin For further information on any of the above, please consult
protection is also advised. In case of contact with the skin, your local Fosroc office - as below.
rinse with plenty of clean water, then cleanse thoroughly
with soap and water. In case of contact with eyes, rinse
immediately with plenty of clean water and seek medical
advice. If swallowed seek medical attention immediately –
do not induce vomiting.
Fire
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
Fosam Company Limited Telephone: +966 2 637 5345 Fax: +966 2 637 5891 email: fosam@fosroc.com
Head Office
Post Box 11081 Regional Offices
Jeddah Sales Office Tel: (02) 608 0999 Fax: (02) 638 0693 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Jeddah – 21453 Jeddah Showroom Tel: (02) 665 0187 Fax: (02) 667 4844 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Saudi Arabia Riyadh Tel: (01) 482 9303 Fax: (01) 482 7562 Medinah Tel: (04) 855 0091 Fax: (04) 855 0047
Dammam Tel: (03) 814 1282 Fax: (03) 814 1581 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875
Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693
www.fosroc.com
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407