Professional Documents
Culture Documents
Nav Composites 03-Beam Jacketing PDF
Nav Composites 03-Beam Jacketing PDF
Nav Composites 03-Beam Jacketing PDF
STRUKTUR KOMPOSIT
DIPLOMA IV TEKNIK INFRASTRUKTUR SIPIL ITS
CHAPTER – 3
BEAM JACKETING
Dosen Pengajar :
Afif Navir Refani, ST., MT.
navir@ce.its.ac.id / +628113411985
IPITS 2015 10
1
LECTURE CONTENTS
Composites Material
Composites Material
Application for
Introduction (concrete –
structural
concrete)
strengthening
Steel – Concrete
Evaluation 2 Evaluasi 1
Composites
Designing Of
Concrete – carbon
Composites Evaluation 3
fiber composites
Member
IPITS 2015 10
2
1
3/12/2019
COMPOSITES
STRUCTURE
CONCRETE EXISTING & NEW CONCRETE
1 2 3
Slab Overlay Beam Jacketing Column Jacketing
CONCRETE COMPOSITES
2
3/12/2019
COMPOSITES STRUCTURE
BEAM JACKETING (FLEXTURE COMPOSITES ELEMENT)
3
3/12/2019
CONCRETE JACKETING
Jacketing a Reinforced concrete member is done to enhance it's strength.
This may be necessary either in case of increase of load or to overcome
deficiencies that may develop over time.
This is mostly done for compression members like columns in a building,
piers and abutments of bridges. The process is similar to wearing a jacket
in extreme weather conditions and hence the name.
The old concrete surface is thoroughly cleared of loose material or Cement
plaster if any and cleaned properly. Reinforcement bars both vertical and
horizontal are provided as per design and concrete is poured.
BEAM JACKETING
4
3/12/2019
BEAM JACKETING
10
5
3/12/2019
BEAM JACKETING
11
BEAM JACKETING
12
6
3/12/2019
Condition where the yield of steel reinforcement and the crushing of outer concrete
compressive fiber occur at the same time.
Or condition when ultimate strain of concrete occur the same time as steel yield strain
13
13
0.85β1 f c' cb
ρb =
fy d
0.85β1 f c' 600
ρb =
fy 600 + f y
14
14
7
3/12/2019
15
15
16
16
8
3/12/2019
17
17
Cc = T1 Cs ' = T2 M n = M n1 + M n 2
0.85 f 'c ab = ( As − As ') f y M n 2 = As ' f s (d − d ') a
M n = ( As − As ') f y d − + As ' f s (d − d ')
a 2
M n1 = ( As − As ') f y d −
2
18
18
9
3/12/2019
19
19
As f y − As ' f s ( As − As ') f y
a= ;a =
0.85 f 'c b 0.85 f 'c b
All the formula above can be used only if all the steel compression is yields,
otherwise the fs value must be calculate accurately.
20
20
10
3/12/2019
21
21
22
22
11
3/12/2019
23
23
a=
As f y − As ' f s
=
(3000)(400) − (1000)(227 ) = 109.02mm
0.85 f 'c b 0.85(30 )(350 )
#5 Calculate φMn :
a
M n = (As f y − As ' f s ) d − + As ' f s (d − d ')
2
109.02
M n = ((3000)(400 ) − (1000 )(227 )) 525 − + (1000)(227 )(525 − 65)
2
M n = 480.812kNm
φMn = 0.8(480 ) = 384.649kNm
24
24
12
3/12/2019
25
25
26
26
13
3/12/2019
27
27
28
28
14
3/12/2019
29
29
30
30
15
3/12/2019
31
31
32
32
16
3/12/2019
33
33
34
17
3/12/2019
35
36
18
3/12/2019
37
38
38
19
3/12/2019
The length of steel headed stud anchors shall not be less than
four stud diameters from the base of the steel headed stud
39
anchor to the top of the stud head after installation.
39
40
40
20
3/12/2019
▰ Vu ≤ Ø Vnh
▰ Vnh = 0,55 bv . d
Dimana :
Vu = Gaya Geser Horizontal Ultimate
Vnh = Gaya Geser Nominal
Ø = 0,75 (geser)
bv = lebar pelat komposit
D = tebal pelat overlay
41
41
42
21
3/12/2019
CASE STUDY 1
43
Case study 1
500
500
CEK :
• Kapasitas Momen Balok Eksisting (300x400) terhadap
Mu
• Kapasitas Momen Balok Setelah jacketing (400x500) 400 400
terhadap Mu
44
22
3/12/2019
MOMENT CAPACITY
EXISTING (30x40)
ENDSPAN
Mutump ≤ Ø Mn
19.127 Kgm ≤ 0.9 x 9.280 Kgm
19.127 Kgm ≤ 8.352 Kgm (NOT OK)
45
MOMENT CAPACITY
EXISTING (30x40)
MIDSPAN
Mulap ≤ Ø Mn
14.345 Kgm ≤ 0.9 x 7.011 Kgm
14.345 Kgm ≤ 6.309 Kgm (NOT OK)
46
23
3/12/2019
Mutump ≤ Ø Mn
19.127 Kgm ≤ 0.9 x 22.149 Kgm
19.127 Kgm ≤ 19.934 Kgm (OK)
47
MOMENT CAPACITY
BEAM JACKETING
(400x500mm)
MIDSPAN
Mulap ≤ Ø Mn
14.345 Kgm ≤ 0.9 x 19.672 Kgm
14.345 Kgm ≤ 17.704 Kgm (OK)
48
24
3/12/2019
END OF LECTURES 3
IPITS 2015 10
49
25