Professional Documents
Culture Documents
Basics and Statics of Particles Introduction
Basics and Statics of Particles Introduction
Basics and Statics of Particles Introduction
Note. Statics deals with equilibrium of bodies at rest, whereas dynamics deals with the motion of bodies
and the forces that cause them.
1.1.1. Vector Quantity. A quantity which is completely specified by magnitude anddirection, is known as a
vector quantity. Some examples of vector quantities are : velocity,acceleration, force and momentum. A
vector quantity is represented by means of a straight line with an arrow as shown in Fig. 1.2. The length of
the straight line (i.e., AB) represents the magnitude and arrow represents the direction of the vector.
The symbol AB also represents this vector, which means it is acting from A to B .
1.1.2. Scalar Quantity. A quantity, which is completely specified by magnitude only, is known as a scalar
quantity. Some examples of scalar quantity are : mass, length, time and temperature.
1.1.3. A Particle. A particle is a body of infinitely small volume (or a particle is a body of” negligible
dimensions) and the mass of the particle is considered to be concentrated at a point. Hence a particle is
assumed to a point and the mass of the particle is concentrated at this point.
lOMoAR cPSD| 3129961
1.1.4. Law of Parallelogram of Forces. The law of parallelogram of forces is used to determine the
resultant* of two forces acting at a point in a plane. It states, “If two forces, acting at a point be
represented in magnitude and direction by the two adjacent sides of a parallelogram, then their resultant
is represented in magnitude and direction by the diagonal of the parallelogram passing through that
point.”
Let two forces P and Q act at a point 0 as shown in Fig. 1.3. The force P is represented in magnitude and
direction by OA whereas the force Q is presented in magnitude and direction by OB. Let the angle
between the two forces be ‘a’. The resultant of these two forces will be obtained in magnitude and
direction by the diagonal (passing through O) of the parallelogram of which OA and OB are two adjacent
sides. Hence draw the parallelogram with OA and OB as adjacent sides as shown in Fig. 1.4. The resultant
R is represented by OC in magnitude and direction.
AC=Q.
In triangle ACD,
AD = AC cos a = Q cos a
In triangle OCD,
and DC =Q sin a
= P2 + Q2 + 2PQ cos a
R = √ p2 + Q2 + 2PQ cos a
Direction of Resultant
Equation (1.2) gives the direction of resultant (R). The direction of resultant can also be obtained by using
sine rule [In triangle OAC, OA = P, AC = Q, OC = R, angle OAC = (180 – a), angle ACO = 180- [θ + 180 – a] =
(a- θ)]
1st Case. If the two forces P and Q act at right angles, then
a = 90°
2nd Case. The two forces P and Q are equal and are acting at an angle a between them.Then the
magnitude and direction of resultant is given as
lOMoAR cPSD| 3129961
It is not necessary that one of two forces, should be along x-axis. The forces P and Q may be in any
direction as shown in Fig. 1.5. If the angle between the two forces is ‘a’, then their resultant will be given
by equation (1.1). The direction of the resultant would be obtained from equation (1.2). But angle e will
be the angle made by resultant with the direction of P.
1.1.5. Law of Triangle of Forces. It states that, “if three forces acting at a point be represented in magnitude
and direction by the three sides of a triangle, taken in order, they will be in equilibrium.”
1.1.6. Lame’s Theorem. It states that, “If there forces acting at a point are in equilibrium, each force will
be proportional to the sine of the angle between the other two forces.”
Suppose the three forces P, Q and Rare acting at a point 0 and they are in equilibrium as
Then according to Lame’s theorem, P is proportional sine of angle between Q and R a sin β.
P / sin β = constant
Proof of Lame’s Theorem. The three forces acting on a point, are in equilibrium and hence they can be
represented by the three sides of the triangle taken in the same order. Now draw the force triangle as
A rigid body will be in equilibrium if the following two conditions are met.
Translational Equilibrium
For an object to be in translational equilibrium the vector sum of the forces acting on it must be zero.
Starting that the vector sum of forces acting on an object is zero is equivalent to:
lOMoAR cPSD| 3129961
∑Fx=0,∑Fy=0,∑Fz=0.∑Fx=0,∑Fy=0,∑Fz=0.
Where Fx , Fy and Fz are the components of a force F in three perpendicular directions. It means that all
the force along the x-axis add to zero. Same is true for forces along y and z axis. From Newton’s second
law of motion,
Thus, when a body is in transitional equilibrium, it ie either at rest or it is moving with constant velocity.
Rotational Equilibrium
For an object to be in rotational equilibrium, the net torque acting on it must be zero.
Stating that the net torque acting on an object is zero means that angular acceleration of the body about
any axis of rotation is zero. So, the body is either at rest or moving with constant angular velocity about
the axis.
States of Equilibrium
Stable equilibrium
A body is in stable equilibrium if it returns to its equilibrium position after it has been displaced slightly as
in the figure. In this equilibrium, C.G. of the body lies low and when the body is displaced from its
equilibrium position, the C.G at this position is higher than before.
Unstable equilibrium
A body is in unstable equilibrium if it does not return to its equilibrium position after it has been displaced
slightly as in the figure. In this equilibrium, C.G. of the body lies high and when the body is displaced from
its equilibrium position, the C.G at this position is lower than before.
Neutral equilibrium
A body is in neutral equilibrium if it always stays in the displaced position after it has been displayed
slightly as in the figure. In this equilibrium height of the C.G. of the body does not change but remains at
the same height from the base in all displaced position.
3. C.G. should lie within the base of the body on displaced position.
lOMoAR cPSD| 3129961
A man carrying a bucket of water in his right-hand leans towards the left-hand side so that vertical line
through the C.G will pass through the base. Due to the same reason, a man carrying a load on his back has
to bend forward. If he wants to carry the load straight upon his back, the vertical line through the C.G.
falls outside the base and cannot carry the road.
Lami’s Theorem
It states that if a particle is in an equilibrium state under the action of three concurrent forces, then each
force is proportional to the sine of the angle between the other two.
Consider three forces P, Q and R are acting on the particle A such that the particle is in equilibrium. If α, β,
and γ are the angles between the three forces as shown in the figure. From lami's theorem we have
Psinα=Qsinβ=RsinγPsinα=Qsinβ=Rsinγ
Since the particle is in equilibrium under the action of three forces, they can be represented in magnitude
and direction by three sides DABC as shown in the figure. i.e. forces P, Q, and R are represented by side
AB, BC and CA respectively. Also ∠A = 180o – β, ∠ B = 180o – γ and ∠ C = 180o – α.
ABsinC=BCsinA=CAsinBPsin(180o−α)∴Psinα=Qsin(180o−β)=Rsin180o−γ)=Qsinβ=RsinγABsinC=BCsinA=C
AsinBPsin(180o−α)=Qsin(180o−β)=Rsin180o−γ)∴Psinα=Qsinβ=Rsinγ
The equivalent force and centroid problem has many guises. In some instances, it is not force that is being
integrated, but volume or area. For instance, suppose that we have bar with a triangular cross section that
is under tension. If the bar is long (>> 4 times the width), we can assume that the tension is uniform
throughout the cross section, mid-length along the member.This is known as a uniform stress distribution
The center of gravity is a point where whole the weight of the body act is called center of gravity. As we
know that every particle of a body is attracted by the earth towards its center with a magnitude of the
weight of the body. As the distance between the different particles of a body and the center of the earth is
the same, therefore these forces may be taken to act along parallel lines. A point may be found out in a
lOMoAR cPSD| 3129961
body, through which the resultant of all such parallel forces acts. This point, through which the whole
resultant (weight of the body acts, irrespective of its position, is known as center of gravity (briefly written
as C.G). It may be noted that every body has one and only one center of gravity.
2.1 Centroid
The plane figures (like triangle, quadrilateral, circle etc.) have only areas, but no mass. The center of area
of such figures is known as Centroid. The method of finding out the Centroid of a figure is the same as that
of finding out the center of gravity of a body.
The center of gravity of a body is always calculated with referrer to some assumed axis known as axis of
reference. The axis of reference, of plane figures, is generally taken as the lowest line of the figure for
calculating y and the left line of the figure for calculating x.
The center of gravity (or Centroid) may be found out by any one of the following methods I. By geometrical
considerations 2. By moments method 3. By graphical method
The center of gravity of simple figures may be found out from the geometry of the figure
2. The center of gravity of a rect angle is at a point, where its diagonals meet eac h other. It is also a mid
point of the length as well a s the breadth of the rectangle as shown in fig
lOMoAR cPSD| 3129961
G = L/2 from AD or BC
G = h/2 from AB or DC
Area = L x
3. The center of gravity of a squa re is a point, where its diagonals meet each oth er. It is a mid point of its
side as shown in fig
4. The center of gravity of a parallelogram is at a point, where its diagonals meet each other. It is also a mid
point of the length as well as the height of the parallelogram as shown in fig
lOMoAR cPSD| 3129961
The center of gravity of a body may also be found out by moments as discussed below. Consider a body of
mass M whose center of gravity is required to be found out. Now divide the body into small strips of masses
whose centers of gravity are known as shown in fig
Example1: Find the center of gravity of a 100 mm x 150 mm x 30 mm T-section. As shown in the fig
y = Σa y = 531000 Y = 94.09 mm
The center of gravity of solid bodies (such as hemisphere, cylinder, right circular solid cone etc) is found
out in the same way as that of the plane figures. The only difference between the plane and solid bodies is
that in the case of solid bodies we calculate volumes instead of areas
Problem 2: solid body formed by joining the base of a right circular cone of height H to the equal base of
right circular cylinder of height h. calculate the distance of the center of gravity of the solid from its plane
face when H = 120 mm and h = 30 mm
Working formula
y = v 1 y 1 + v 2 /v1 + v2
Solution
y = 40.7 mm
The center of gravity of such a section is found out by considering the main section; first as a complete one
and then deducting the area of the cut out hole that is taking the area of the cut out hole as negative. Now
substituting the area of the cut out hole as negative, in the general equation for the center of gravity, so
the equation will become
x = a1 x1 - a2 x 2/ a1 - a2
Or
y = a1 y1 - a2 y 2/a1 - a2
8 Moment of Inertia
A second quantity which is of importance when considering beam stresses is the Moment of Inertia. Once
again, the Moment of Inertia as used in Physics involves the mass of the object. The Moment of Inertia is
obtained by breaking the object into very small bits of mass dM, multiplying these bits of mass by the square
of the distance to the x (and y) axis and summing over the entire object. See Diagram
For use with beam stresses, rather than using the Moment of Inertia as discussed above, we will once again
use an Area Moment of Inertia. This Area Moment of Inertia is obtained by breaking the object into very
small bits of area dA, multiplying these bits of area by the square of the distance to the x (and y) axis and
summing over the entire object.
The actual value of the moment of inertia depends on the axis cho sen to calculate the moment of the
inertia with respe ct to. That is, for a rectangular object, the mom ent of inertia about an axis passing
lOMoAR cPSD| 3129961
through the ce ntroid of the rectangle is: I = 1/12 (base * d epth3) with units of inches4., while the moment
of inertia with respect to an axis through the base of the rectangle is: I = 1/3 (base * depth3) in4. See
Diagram 6. Note that the moment of inertia of any o bject has its smallest value when calculated with respe
ct to an axis passing through the centroid of the object.
Moments of inertia abo ut different axis may calculated using the Parallel Axis Theorem,
which may be written: Ixx = Icc + Adc-x2 This says that the moment of inertia about any axis (Ixx) parallel
to an axis through the ce ntroid of the object is equal to the moment of i nertia about the axis passing
through the centroid (Icc ) plus the product of the area of the object and the distance between the two
parallel axis (Adc-x2).We lastly take a moment to define several other concepts related to the Moment of
Inertia.
Radius of Gyration: rxx = (Ixx/A )1/2 The radius of gyration is the distance from an axis which, if the entire
area of the object were lo cated at that distance, it would result in the same moment of inertia about the
axis that the object has.
Polar Moment of Inertia J = ∑(r2 )dA The polar moment of inertia is the su m of the produce of each bit of
area dA and the radial distance to an origin squared. In a case as shown in belowthe polar moment of inertia
in relate d to the x & y moments of inertia by: J = Ixx + Iyy.
One final comment - all the su mmations shown above become integrations as we let the dM's and dA's
approach zero. And, whi le this is important and useful when calcula ting Centroids and Moments of Inertia,
the summ ation method is just as useful for understanding the concepts involved.