Professional Documents
Culture Documents
Notes PDF
Notes PDF
Notes PDF
User Guide
JOSAM
cam-aligner
T 163 1 1508
1
Table of Contents
JOSAM cam-aligner user guide................................................................................................... 7
System description ................................................................................................................. 8
Agreed functionality ................................................................................................................... 8
Technical data ............................................................................................................................ 9
Measurement specifications .................................................................................................. 9
Other specifications ............................................................................................................... 9
System Requirements ............................................................................................................ 9
Recommended ................................................................................................................... 9
Minimum ............................................................................................................................ 9
Required operating system .............................................................................................. 10
Component description............................................................................................................ 11
Camera sensor CA1010 .................................................................................................... 11
Inclinometer unit CA1007, inclinometer kit CA ANGLE K ................................................ 12
Reflective targets.............................................................................................................. 12
Wireless Server CA1009 ................................................................................................... 13
Wheel adapter .................................................................................................................. 13
Frame gauges ................................................................................................................... 13
Low friction plates ............................................................................................................ 14
Reference blocks .............................................................................................................. 14
Measurement reference definition.......................................................................................... 15
Chassis centre line reference ........................................................................................... 15
Rear axle reference .......................................................................................................... 15
Installation guide .................................................................................................................. 16
Introduction.............................................................................................................................. 16
Install wireless server (Windows 7 and 8.1)............................................................................. 17
Installing the server device driver manually ........................................................................ 17
Step 1 (Windows 7) .......................................................................................................... 17
Step 1 (Windows 8.1) ....................................................................................................... 18
Step 2 (Windows 7 and 8.1) ............................................................................................. 19
JOSAM cam-aligner installation ............................................................................................... 24
Software settings...................................................................................................................... 29
General: ................................................................................................................................ 30
System standby: ............................................................................................................... 30
Working mode: ................................................................................................................. 30
Reference: ........................................................................................................................ 30
Toe unit: ........................................................................................................................... 30
Steerbox measurement type:........................................................................................... 30
Language: ......................................................................................................................... 31
Communication: ................................................................................................................... 31
Pairing ............................................................................................................................... 32
Report: .................................................................................................................................. 35
Report style: ..................................................................................................................... 35
Report header and preview: ............................................................................................ 35
Graphics:............................................................................................................................... 36
Registration: ......................................................................................................................... 37
Wheel alignment ...................................................................................................................... 39
Measurement preparations ..................................................................................................... 41
Mount frame gauges ............................................................................................................ 41
Mounting frame gauges when measuring the axle(s) on a ‘dolly’....................................... 42
Mount wheel adapters ......................................................................................................... 43
Mount reference blocks on wheel adapters ........................................................................ 43
Mount inclinometer unit ...................................................................................................... 44
Create work order .................................................................................................................... 45
Vehicle identification number (VIN)................................................................................. 45
Mileage ............................................................................................................................. 45
Make & Model .................................................................................................................. 45
Employee .......................................................................................................................... 45
Date .................................................................................................................................. 46
Measure............................................................................................................................ 46
Comments ........................................................................................................................ 46
Select vehicle type .................................................................................................................... 47
Select vehicle type ............................................................................................................ 47
Select axle configuration .................................................................................................. 47
Select vehicle specification .............................................................................................. 48
Steering gear side ............................................................................................................. 48
Configure a new axle configuration ................................................................................. 49
Configure a vehicle specification...................................................................................... 51
All values window - select measurement functions ................................................................ 53
All values vehicle: ............................................................................................................. 53
All values vehicle: ............................................................................................................. 54
Align vehicle ............................................................................................................................. 56
Select reference axle ........................................................................................................ 56
Using the driven axle of the tractor as the reference ...................................................... 57
Using the rigid axle on the trailer as the reference ........................................................ 61
Measurement ....................................................................................................................... 65
Run-out ..................................................................................................................................... 65
Step 1:............................................................................................................................... 65
Step 2:............................................................................................................................... 66
Step 3:............................................................................................................................... 66
Step 4:............................................................................................................................... 67
Step 5:............................................................................................................................... 67
Step 6:............................................................................................................................... 68
Step 7:............................................................................................................................... 68
Toe & Camber after run-out..................................................................................................... 70
Procedure when measuring after run-out: .......................................................................... 70
Toe & Camber - rolling 1 axle ................................................................................................... 73
Procedure when measuring by rolling: ................................................................................ 73
Toe & Camber - multi axle roll ................................................................................................. 77
Floor reference ......................................................................................................................... 82
Using the inclinometer unit in combination with caster / KPI measurements................ 82
Caster / KPI / maximum turn.................................................................................................... 85
Using the inclinometer unit in combination with Caster / KPI measurements ............... 85
Adjust maximum turn............................................................................................................... 90
Adjustment ........................................................................................................................... 93
Adjustment ............................................................................................................................... 93
Absolute / relative .................................................................................................................... 95
Adjust total toe ......................................................................................................................... 96
Adjust individual toe ................................................................................................................ 97
Adjust out of square ................................................................................................................. 99
Adjust camber ........................................................................................................................ 101
Adjust double steering left/right............................................................................................ 103
Adjust caster ........................................................................................................................... 106
Steering box position.............................................................................................................. 108
Equipment calibration ............................................................................................................ 111
Calibrate camera .................................................................................................................... 111
Calibrate inclinometer ............................................................................................................ 116
System maintenance .............................................................................................................. 119
Cameras and inclinometer unit ...................................................................................... 119
Reflective targets............................................................................................................ 119
Other equipment ............................................................................................................ 119
Measurement documentation ............................................................................................... 121
Order management ................................................................................................................ 121
Reports ................................................................................................................................... 124
JOSAM cam-aligner
7
JOSAM cam-aligner
System description
Agreed functionality
• The JOSAM cam-aligner system is designed for wheel alignment and frame check of
all commercial vehicles.
• The JOSAM cam-aligner system provides measurement of total toe, individual toe,
axle offset, out of square, camber, caster, KPI, toe out on turn, max turn angles and
steering gear middle position.
• The JOSAM cam-aligner system enables dynamic toe and camber measurement while
in driving position. No lifting of the axles with run-out compensation is required
during this measurement.
• The JOSAM cam-aligner system enables performing of run-out compensation of rims
and wheel adapters, which is necessary for caster, KPI and turn angle measurements.
• The JOSAM cam-aligner system enables measurements to be performed fast and
reliable on all types of commercial vehicles.
• The JOSAM cam-aligner system uses wireless communication technology for
transmission of information between camera sensors and computer.
CAR-O-LINER AB may not be held responsible for any losses, damages or other effects,
economical, human or otherwise, derived from using this equipment in ways not explicitly
specified within this document.
Updated 2015-01-12
8
JOSAM cam-aligner
Technical data
Measurement specifications
Feature Accuracy Measurement range
Total Toe <0,4 mm/m ± 40 mm/m
Individual Toe <0,2 mm/m ± 40 mm/m
Camber <3’ ± 6°
Other specifications
Operating time with fully charged >16h
batteries
Charging unit operating voltage 100-240V, 50-60Hz
Operating temperature -5° to +40° Celsius
Wireless communication 2,4GHz Spread Spectrum Wireless Industrial
Transceiver with frequency range 2401 - 2495 MHz
System Requirements
Recommended
Central Processing Unit (CPU) Intel i5 2,3GHz or higher
Memory (RAM) 4GB
Available hard disk space 80GB
Graphics Super SVGA (1024 x 768) or higher-resolution video
adapter and monitor
Media CD-ROM or DVD drive
Ports 1xUSB2.0
Minimum
Central Processing Unit (CPU) Intel i3 1,6 GHz
Memory (RAM) 4GB
Available hard disk space 40GB
Graphics Super SVGA (1024 x 768) or higher-resolution video
adapter and monitor
Ports 1xUSB2.0
9
JOSAM cam-aligner
Additional system requirements might apply to get the above mentioned operating systems
fully functional, please check with your operating system supplier.
Updated 2015-01-12
10
JOSAM cam-aligner
Component description
Camera sensor CA1010
The camera sensor is a rugged, high precision sensor specially
designed to measure angles and distance relative to a reflective
target. It has a strong housing with rubber protection at both ends.
The camera lens and built-in flasher is protected by a hardened front
glass.
The picture is analyzed by a microprocessor within the camera sensor itself, and information
is sent to the computer by wireless communication. The computer finishes the calculations,
giving the three angles α (alfa), β (beta) and camber as well as the distance to the target as a
result. These parameters are then used by the computer software to calculate the wheel
angles.
The camera is equipped with three electronic inclinometers as well as a gyroscope. The
signals from these sensors are combined with the data from the camera to produce a very
powerful tool to be used for wheel alignment. The gyroscope is used to extend the angle
range to handle max turn angles for steerable axles. The electronic inclinometers are used to
calculate camber, castor and KPI directly on the wheel itself.
The camera sensor is powered by a built-in battery pack, and the batteries are recharged
every time the camera is placed in the charging cradle. The operating time of the batteries is
>16 hours, depending on the way of use of the system. The camera has a standby mode
where it consumes only 15% of the power. In standby mode the wireless connection is still
active while the camera part itself is switched off. The software in the computer
automatically switches the camera from standby mode to operation mode as needed.
11
JOSAM cam-aligner
The inclinometer unit is used to compensate influences from floor inclination, difference in
tire size or tire pressure while measuring. The inclinometer monitors not only the horizontal
position of the axle, but also monitors the angle of inclination of the axle while lifting the
front axle. This enables the operator to measure correct caster and KPI values in lifted
position without levelling the vehicle or the axle beam. By using the inclinometer unit during
rolling measurement, the inclinometer monitors the horizontal position of the axle while
moving the vehicle half a wheel turn. In this way high accuracy camber values can be
achieved even on an uneven floor.
Reflective targets
The reflective targets are markers
that the camera sensor uses to
determine angles and distances.
These markers need to be kept
clean, to maintain high
measurement accuracy and long
life time of the system. For
cleaning recommendations, please
see chapter "System
maintenance".
Note! To keep the marker clean, make sure to always avoid touching the reflective
surfaces on each side of the target when handling them.
12
JOSAM cam-aligner
Wheel adapter
Frame gauges
The frame gauges work
according to a self-centering
principle. When mounted to a
vehicle they determine the
chassis centre line, which is the
standard reference in a camera
wheel alignment system. The
reflective targets are placed at
the end of each frame gauge.
13
JOSAM cam-aligner
Reference blocks
The reference blocks are used to correctly position the cameras when doing a
multi-roll measurement.
Updated 2015-06-18
14
JOSAM cam-aligner
Updated 2015-03-02
15
JOSAM cam-aligner
Installation guide
Introduction
JOSAM cam-aligner is the measurement data container for all JOSAM camera applications:
• Wheel alignment
• Radar alignment (ACC / AICC)
• Frame check
Please take the time to read the instruction thoroughly before you start the installation.
Note! Make sure you have administrator rights during installation and usage.
Note! Make sure to install the wireless driver before the software is installed.
Note! Make sure that the wireless server can communicate freely, do not place it
inside a cabinet, always outside.
Updated 2015-01-09
16
JOSAM cam-aligner
Plug the wireless server into a USB port, and Windows will find the server. If your computer
is connected to the Internet, Windows Update will automatically install the device driver.
Otherwise Windows will tell you that the device driver was not installed correctly. In that
case, please follow the steps described below.
17
JOSAM cam-aligner
18
JOSAM cam-aligner
In the Device Manager you will see the TruckCam Wireless unit displaying a question mark
warning. Right-click on “TruckCam Wireless” and choose [Update driver software].
19
JOSAM cam-aligner
20
JOSAM cam-aligner
Specify a location by browsing to the driver folder on the USB stick. Click [Next].
Click [Install this driver software anyway]. The device driver for the wireless server is
perfectly Windows compatible and can be installed without risks, although this warning
might occur during installation.
21
JOSAM cam-aligner
Click [Close] when the device driver has been completely installed.
22
JOSAM cam-aligner
The TruckCam Wireless unit will now show up properly in the list of USB controllers.
Updated 2015-06-30
23
JOSAM cam-aligner
24
JOSAM cam-aligner
25
JOSAM cam-aligner
Click "I accept the license agreement" and then click [Next].
26
JOSAM cam-aligner
Click [Next].
27
JOSAM cam-aligner
Click [Finish] when installation is complete. If the above "Restart" warning dialog shows,
please click [Restart] to restart the computer before starting to use your cam-aligner system,
in order for the software to work properly.
Updated 2015-06-30
28
JOSAM cam-aligner
Software settings
Double click on the JOSAM cam-aligner program icon to start the alignment software. Start
up the cameras and, when applicable, the inclinometer unit by pressing the ON/OFF button
on the units respectively.
Click [Setup ] to enter the program setup. Before using the system for the first time, it is
required to enter the setup area to configure the program settings. These settings will then
be stored in the program when you click [Save ] in the setup window.
29
JOSAM cam-aligner
General:
System standby:
This is where you set the time of system inactivity before the system enters standby mode.
A 0 [zero] value indicates that the standby mode is de-activated.
Working mode:
Sets the system working mode to Standard or Advanced.
Reference:
One chooses whether to use Midpoint axle reference (here referred to as “Center line”) or
Rear axle reference (“Rear axle”). The choice made will only apply when the reference switch
in Define Vehicle is put to "Rear axle”, see chapter "Measurement reference definition".
Toe unit:
Choose whether to measure toe angles in mm/m or degrees and minutes.
30
JOSAM cam-aligner
Language:
Select system language from the drop-down list. The new language will be active after
restart of the software.
Communication:
It is vital to the functionality of the system that you enter the correct radio numbers of the
cameras – and, when applicable, the inclinometer unit – here in order for the wireless
connections to work properly.
When using the inclinometer unit, please click the [Active] square box to activate the unit
during measurements.
The first time the system is used the wireless communication has to be configured before
the system is fully functional. This is done by entering the serial numbers of the units in your
system into the software and pairing the units to the wireless server.
31
JOSAM cam-aligner
Pairing
Enter the Pairing function of the JOSAM cam-aligner system by clicking [Pairing ] in the
“Setup” window. Follow the steps presented by the help texts in the grey square on the
computer screen. When experiencing problems with wireless communication or if adding an
inclinometer unit to a system already in use, you might need to ‘Pair’ the system units.
Press and hold both OK buttons on each camera and, when applicable, the OK button on the
inclinometer unit for 7 seconds to activate the service channel of the units. This is indicated
by the blue LEDs on the units, which start to blink once the unit has entered pairing mode.
32
JOSAM cam-aligner
Wait until the red squares on the screen have turned green for all available units.
The squares on the screen will change from green to red and back to green again as the
changing of communication channels is performed on all units. Please wait during this
procedure.
33
JOSAM cam-aligner
The system will tell you when the pairing of the units is done by a message in the grey help
text square. Now the units should communicate with each other.
34
JOSAM cam-aligner
Report:
Report style:
Choose whether you want a separate report sheet for the ‘before’ and ‘after’ values
respectively, or if you want them presented on the same report sheet. You can also choose
whether or not to show the offset value of axles on the report sheet.
35
JOSAM cam-aligner
Graphics:
This is where you specify at which measured values the graphics move on screen and on the
final measurement report. These values will of course adapt automatically to a change in toe
measurement unit on the Main setup page. To go back to the default values, click [Set
Default].
36
JOSAM cam-aligner
Registration:
Note! You can run the software unregistered for 30 days, after that the measurement
functions are unavailable. Register the software and its different plug-ins as soon as
possible after installation to prevent any problems later on.
Select the plug-in that needs to be registered from the list, and select [Register ], a
window will now pop-up.
37
JOSAM cam-aligner
Enter the CD-key you received in the upper field, and press this link
.
Create a user ID and fill in the required data on the website, when finished you receive a
lock-up code. Enter this lockup code in the lower field and press [Lockup ].
Note! Save the CD-keys you have received together with the user information from
our website for support reasons.
Updated 2015-01-12
38
JOSAM cam-aligner
Wheel alignment
For all measurement sequences described below, start the software by double clicking on
the program icon.
Follow the necessary steps for preparation as described in "Measurement preparation" and
"Calibration of equipment".
In the “All Values” measurement window, select the axle you want to measure by clicking on
the axle, or select [All values axle ]. The selected axle is now indicated with a light
blue square, and the measurements possible are shown in the top menu.
39
JOSAM cam-aligner
40
JOSAM cam-aligner
Measurement preparations
Before you start measuring the vehicle, please complete the below mentioned steps:
• Check that all vital parts, like bolt joints and bushings, are free of any excessive play.
Note! Play will have influence on wheel positions and measurements.
• Check tire pressure, tire size and inflate the tires to the specified pressure.
• Check if the floor or other surface that you’re measuring on is reasonably flat or use
the inclinometer unit to compensate such influences.
Make sure the frame gauges are levelled, by checking the built-in spirit level and adjusting
the frame gauges if necessary.
There are several different adapters available to make it easier to mount the frame gauges
to the vehicle, such as bumper adapters and chassis extenders, please check out the
accessories list in the product sheet or contact your local distributor for further information.
41
JOSAM cam-aligner
Place the reflective targets on the frame gauges. The best way to ensure that the reflective
targets are positioned correctly is to trust the indicators on the reflective targets and lay the
targets out according to the indicators on the targets. Once laid out correctly, fit them to the
frame gauges.
and
or
Mount the tow bar adapter to the towing eyelet. Mount the front frame gauge by placing
the frame gauge hangers in the correct position on the tow bar adapter bar.
Mount a frame gauge in the rear end of the axle frame (the ‘dolly’).
Place the four reflective targets in their correct positions, as described above.
Check that the front frame gauge is perpendicular to the tow bar by eye sight.
42
JOSAM cam-aligner
They are mounted by fitting the hooks at the end of the wheel adapter legs either on the
inside of the rim or between rim and tire, depending on rim make, and rotating the knob on
the side of the wheel adapter to secure it. For light commercial vehicles like vans,
transporters etc, use the smaller leg with the van hook on the wheel adapter and place it
between rim and tire.
43
JOSAM cam-aligner
Take the inclinometer out of the TC-395 Charging Cradle. Mount the CA1007 Inclinometer
Unit into the CA1065 Inclinometer Bar by inserting the unit into the slot of the bar and by
tightening the screws in order to clamp the unit to the bar.
Note! Before use with the measurement software, the mounted inclinometer unit and
bar must be calibrated using the built-in inclinometer calibration function in the
software. See chapter "Calibrate inclinometer".
Updated 2015-06-25
44
JOSAM cam-aligner
Mileage
Enter the mileage of the vehicle.
Employee
Enter the name of the person performing the measurement.
45
JOSAM cam-aligner
Date
The date of measurement is filled in automatically when starting a new measurement.
Measure
Choose type of measurement (Wheel alignment or Frame check).
Comments
Add any comments, they will be printed on the report sheet.
Updated 2015-06-25
46
JOSAM cam-aligner
47
JOSAM cam-aligner
When ready continue by pressing the save and continue button and you will be
forwarded to the all values vehicle window.
48
JOSAM cam-aligner
49
JOSAM cam-aligner
After clicking to add a new axle configuration the following window will open. On the
left side a list of available axle types are shown. A configuration is built from the front and
works backwards. Click on an axle type in the list on the left and it will be added to the
configuration on the right. When a wrong axle is selected, you can click on it in the right list
and it will be removed.
When ready just add a name of the created axle configuration and click to save it.
50
JOSAM cam-aligner
51
JOSAM cam-aligner
After clicking to add a new vehicle definition the following window will open. The axle
list is shown on the left side, on the right side you can add tolerances for wheel angles. NaN
means not a number which equals no tolerance value.
When ready just add a name of the created vehicle specification and click to save it.
Updated 2015-03-02
52
JOSAM cam-aligner
Multi axle roll (note: this option is not available in the basic software)
53
JOSAM cam-aligner
Select an axle in the left axle list, the selected axle is marked with a blue square. When the
axle has been measured before the measurement results are shown on the right.
54
JOSAM cam-aligner
Perform run-out
Measure floor reference used during measurement of caster, KPI, toe out on turns
and maximum turn
Measure caster, KPI, toe out on turns and maximum turn
Adjust
Updated 2015-03-02
55
JOSAM cam-aligner
Align vehicle
This function is designed as a help function, used to line up the two parts of an articulated
vehicle before continuing with regular measurements and adjustments.
Note! The articulated vehicles for which this function is meant are vehicles with at
least one steerable axle in the rear, e g behind the articulation point, that is actively
steered from the front part of the vehicle. One example is a tractor/trailer
combination where the semitrailer has one or more steerable axle(s) connected to the
fifth wheel (sometimes called a “city trailer”). Regular tractor-trailer combinations as
well as articulated buses with only stiff axles in the rear should always be measured as
two separate vehicles, a tractor unit and a trailer unit.
56
JOSAM cam-aligner
Mount the frame gauges on the tractor unit, and place a wheel adapter with camera on the
main driven axle of the tractor unit. Perform a "run-out compensation" of the wheel
adapter.
Follow the instructions given by the help text in the gray square and animations.
1. Aim the camera reasonably horizontal at the front marker and press the OK button on the
camera.
2. Aim the camera reasonably horizontal at the rear marker and press the OK button on the
camera.
57
JOSAM cam-aligner
3. Move the rear frame gauge to the end of the trailer, as shown in above illustration.
4. Make sure the camera is still aiming at the rear marker, then press the OK button on the
camera.
58
JOSAM cam-aligner
5. While making sure the camera continues to aim at the rear marker at all times, move the
tractor unit forward until the parallelism bar graph on the computer screen shows zero.
59
JOSAM cam-aligner
Measurement is done, and tractor unit and trailer unit are now parallel.
60
JOSAM cam-aligner
Mount the frame gauges on the trailer unit, and place a wheel adapter with camera on the
main driven axle of the tractor unit. Perform a "run-out compensation" of the wheel
adapter.
Follow the instructions given by the help text in the gray square and animations.
1. Aim the camera reasonably horizontal at the rear marker and press the OK button on the
camera.
2. Aim the camera reasonably horizontal at the front marker and press the OK button on the
camera.
61
JOSAM cam-aligner
3. Move the front frame gauge to the front of the tractor unit as shown in above illustration.
4. Make sure the camera is still aiming at the front marker, then press the OK button on the
camera.
62
JOSAM cam-aligner
5. While making sure the camera continues to aim at the rear marker at all times, move the
tractor unit forward until the parallelism bar graph on the computer screen shows zero.
63
JOSAM cam-aligner
Measurement is done, and tractor unit and trailer unit are now parallel.
Updated 2015-03-03
64
JOSAM cam-aligner
Measurement
Run-out
To compensate the wheel adapter for skewness in rims and/or the wheel adapter itself, the
software enables you to perform a run-out compensation. This function guides the operator
to adjust the two knobs on the wheel adapter to compensate for above mentioned
skewness. Please note that one of the knobs is marked with a white spot to help identify one
knob from the other.
Follow the steps presented by the help texts in the white square on the computer screen.
Step 1:
• Lift the axle so that the wheels are free from the ground in order to rotate them
• Turn the wheel so that the white knob is pointing straight up.
• Mount and lock the camera pointing straight upwards.
• Rotate the wheel so that the camera aims towards the far marker.
• Press OK when the green LED lights up.
65
JOSAM cam-aligner
Step 2:
• Turn the wheel so that the white knob points straight up again.
• Turn the camera so that it points straight down.
• Rotate the wheel so that the camera aims towards the far marker.
• Press OK when the green LED lights up.
Step 3:
• Adjust to zero using the white knob.
• Confirm by pressing OK.
66
JOSAM cam-aligner
Step 4:
• Turn the wheel so that the black knob is pointing straight up.
• Turn the camera so that it points straight up.
• Rotate the wheel so that the camera aims towards the far marker.
• Press OK when the green LED lights up.
Step 5:
• Adjust to zero using the black knob.
• Confirm by pressing OK.
67
JOSAM cam-aligner
Step 6:
• Turn so that the camera points straight up.
• Rotate the wheel so that the camera aims towards the far marker.
• Confirm by pressing OK.
Step 7:
Run-out complete!
Press OK on the camera to perform a run-out on the next wheel, or press [Back] in the top
menu to start measuring.
68
JOSAM cam-aligner
• When the run-out is within tolerance you will get a green check mark like in the
picture above with the deviation between black and white knob.
• When the run-out is outside tolerance you will get a red cross like the picture below
and the run-out procedure should be done again on this wheel.
The wheel adapter is now compensated for any skewness in rim and/or the wheel adapter
itself, and the spindle of the wheel adapter is now, figuratively speaking, an extension of the
axle.
Updated 2015-08-06
69
JOSAM cam-aligner
Click [Toe Camber After Run-Out ] in the “All values axle” window.
When measuring a front axle, the software will ask you to put the steering gear in middle
position when selected to do so in the program setup.
Click the check button on the right lower part of the screen to confirm that you have
put the steering gear mechanically in the middle position.
Follow the instructions given by the help text in the gray square and animations.
70
JOSAM cam-aligner
1. Aim the camera reasonably horizontal at the nearest marker and press the OK button on
the camera.
71
JOSAM cam-aligner
2. Aim the same camera reasonably horizontal at the far marker. Press the OK button on the
camera.
3. Repeat the same procedure on the opposite side to complete the measurement.
The measured toe and camber values, and in applicable cases the axle offset and steering
gear middle position, are displayed on the computer screen. Here you can select to store the
values before or after adjustment. When using a specification the software will indicate if
the measured values are within or outside specification.
before adjustment
after adjustment
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-06-25
72
JOSAM cam-aligner
Click [Toe Camber After Run-Out ] in the “All values axle” window.
When measuring a front axle, the software will ask you to put the steering gear in middle
position when selected to do so in the program setup.
Click the check button on the right lower part of the screen to confirm that you have
put the steering gear mechanically in the middle position.
Follow the instructions given by the help text in the gray square and animations.
73
JOSAM cam-aligner
1. Aim the camera reasonably horizontal at the far marker and press the OK button on
the camera.
2. Aim the same camera reasonably horizontal at the near marker. Press the OK button
on the camera.
3. Repeat the same procedure on the opposite side.
74
JOSAM cam-aligner
4. Slowly roll the vehicle half a wheel turn in the driving direction, until the measured
wheel angle values appear on the screen, to complete the measurement.
75
JOSAM cam-aligner
The measured toe and camber values, and in applicable cases the axle offset and steering
gear middle position, are displayed on the computer screen. Here you can select to store the
values before or after adjustment. When using a specification the software will indicate if
the measured values are within or outside specification.
before adjustment
after adjustment
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-06-25
76
JOSAM cam-aligner
Note! Check that the cameras and reference blocks are fitted with arrow stickers and
reference stickers from the 16776 arrow sticker kit.
77
JOSAM cam-aligner
Choose which axles to roll simultaneously by clicking on the axles on the screen. We
recommend to equip all wheels with wheel adapters and measure the complete vehicle in
one roll.
If you have selected to measure the steering gear middle position in the setup you have to
put the steering gear in the middle position before the measurement.
Note! Make sure the steering gear is in the correct middle position mechanically.
Follow the instructions given by the help text in the gray square and animations.
Start the measurement on the opposite side of the steering box position on the first axle
with the following 3 steps:
78
JOSAM cam-aligner
Perform the same procedure on all wheels by walking around the vehicle ending up at the
front wheel on the driver position.
Note! Leave the camera in the last position since it is the reference for rolling 180°.
79
JOSAM cam-aligner
Slowly roll the vehicle half a wheel turn in the driving direction, until the background of the
roll value turns green.
Then repeat the measuring procedure in the opposite direction, starting at the steering box
position on the first axle with the following 3 steps:
Note! Move the camera back into the slot before performing a measurement!
2. Aim the camera to the rear marker, click OK.
3. Place the camera so that the reference surface hits the surface of the reference
block.
80
JOSAM cam-aligner
The measured values are displayed on the computer screen. Select to store the values
before or after adjustment. When using a specification the software will indicate if the
measured values are within or outside specification.
before adjustment
after adjustment
The program will then return to the “All values vehicle” measurement window. All measured
values will be displayed on the measured vehicle.
Updated 2015-06-25
81
JOSAM cam-aligner
Floor reference
Using the inclinometer unit in combination with caster / KPI measurements
Caster, KPI can be measured in two ways, either in lifted position or with the vehicle placed
on floating plates.
Normally in order to have realistic values of castor and KPI in ride height, in both cases the
rear of the vehicle should be compensated with the same height lifted or the height of the
floating plates. By using the inclinometer unit with a floor reference measurement, this
compensation at the rear can be eliminated as the inclinometer measures the angle change
from ride height to lifted position or position on floating plates.
Normally in order to get correct KPI values when measuring in a lifted position, the axle
beam must be horizontally levelled. By using the inclinometer unit this manual levelling is
not necessary as the inclinometer unit is monitoring the angle changes of the axle beam and
compensates the measurement by these angle changes.
It is necessary to use the inclinometer unit when measuring on floating plates in order to get
correct and accurate caster values. The reason is that while turning the vehicle will tilt left to
right which changes the angle of the axle beam. The inclinometer unit is monitoring these
changes in order to get accurate caster and KPI values.
Mount or hang the inclinometer on the axle you want to measure using the hanger adapters.
Note! The LEDs and OK button on the inclinometer unit should always face forward in
the driving direction!
82
JOSAM cam-aligner
Click [Take Value] or press the OK button on the inclinometer unit. The software saves the
angle of the axle in the driving position.
When the floor reference value is saved, click [End] to return to the “All Values”
measurement window.
Lift the front axle to make a run out compensation on both sides. This compensation is
required to get accurate caster and KPI values.
83
JOSAM cam-aligner
Perform a caster / KPI measurement, by taking the first picture of the first camera on the
front target the inclinometer registers the angle of the axle in lifted position or on floating
plates. The software compares the lifted value with the value taken in the ride position and
will compensate the difference to the caster value. In this way accurate and realistic
measurement values are ensured.
Updated 2015-03-02
84
JOSAM cam-aligner
Normally in order to have realistic values of castor and KPI in ride height, in both cases the
rear of the vehicle should be compensated with the same height lifted or the height of the
floating plates. By using the inclinometer unit with a floor reference measurement, this
compensation at the rear can be eliminated as the inclinometer measures the angle change
from ride height to lifted position or position on floating plates.
Normally in order to get correct KPI values when measuring in a lifted position, the axle
beam must be horizontally levelled. By using the inclinometer unit this manual levelling is
not necessary as the inclinometer unit is monitoring the angle changes of the axle beam and
compensates the measurement by these angle changes.
It is necessary to use the inclinometer unit when measuring on floating plates in order to get
correct and accurate KPI values. The reason is that while turning the vehicle will tilt left to
right which changes the angle of the axle beam. The inclinometer unit is monitoring these
changes in order to get accurate caster and KPI values.
Click [Maximum turn / caster / KPI ] in the “All values axle” window.
Follow the instructions given by the help text in the gray square and animations.
On both sides of the vehicle, starting on opposite side of the steering gear:
85
JOSAM cam-aligner
1. Aim the camera reasonably horizontal at the front marker and press the OK button on the
camera.
2. Aim the camera reasonably horizontal at the rear marker and press the OK button on the
camera.
86
JOSAM cam-aligner
3. Repeat the same procedure on the opposite side to complete the measurement.
5. Turn smoothly to maximum left and wait until green light appears in the black square
above the wheel on the computer screen.
6. Turn smoothly to maximum right and wait until green light appears in the black square
above the wheel on the computer screen.
87
JOSAM cam-aligner
7. Turn back to straight ahead position until values are shown on the computer screen.
88
JOSAM cam-aligner
To avoid taking new reference measurements against front and rear markers:
click [Adjust turn angles ] to adjust the toe out on turn and max turn angles.
You can also select to store the values before or after adjustment. When using a
specification the software will indicate if the measured values are without or outside
specification.
before adjustment
after adjustment
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
89
JOSAM cam-aligner
The screen will show live values during adjustment for a time frame of 15 seconds, after
which you will have to return to +-10° of the straight ahead position to update angle
calibration data. After returning close enough to the straight ahead position for the cameras
to see the markers, you are able to turn the wheels out again to continue adjustments.
90
JOSAM cam-aligner
When having 5 seconds left to turn the wheels the clock will turn yellow. After that the 15
second time frame is up by the ‘time out’ indicator turning red and the live values disappear
from the screen.
When the adjustments are done, click [Back] and repeat the measurement sequence as
described in "Caster / KPI / maximum turn", to check the aligned axle.
91
JOSAM cam-aligner
Click [restart ] if you want to start the complete measuring process again.
Updated 2015-03-02
92
JOSAM cam-aligner
Adjustment
Adjustment
When diagnostic measurements show that an adjustment is needed, you can choose to
adjust any of the parameters individual and total toe, out of square, camber, maximum turn
as well as double steered vehicles, using the “Adjust” function of the software.
In the “All values axle” window, select the axle you want to align by clicking on the axle in
the left axle list. The selected axle is marked with a light blue square around it.
Click [Adjust ].
93
JOSAM cam-aligner
Choose the desired function by clicking the appropriate button on the computer screen.
Adjust camber
Adjust caster
Updated 2015-03-03
94
JOSAM cam-aligner
Absolute / relative
The ‘Absolute’ method presents the actual measurement value at all times, based on
continuous measurements. When doing the alignment, the user has to consider
influences of lifting, tilting etc on measurement values. This method is only possible
to use when measuring after run-out. When using the ‘Absolute’ alignment method,
the measurement can be performed independently of when the adjustment is made
by clicking [Absolute].
The ‘Relative’ alignment method recalls the previously measured values independent
of lifting, tilting etc. This method provides the possibility to adjust directly to a
desired value.
Note! When using the ‘Relative’ alignment method, it is of vital importance that you
don’t start the alignment process, i.e. there is no change to wheel or axle angles,
before clicking [Relative] to start the measurement.
Updated 2015-03-02
95
JOSAM cam-aligner
2. Choose whether you want to align using the ‘Absolute’ or the ‘Relative’ method by clicking
Adjust to the desired value by turning the tie-rod. The background color is grey when no
tolerance is set for the value to adjust, or red/green when a tolerance is set like on the
example above.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
96
JOSAM cam-aligner
2. Choose whether you want to align using the ‘Absolute’ or the ‘Relative’ method by clicking
97
JOSAM cam-aligner
Adjust to the desired value. The background color is grey when no tolerance is set for the
value to adjust, or red/green when a tolerance is set like on the example above.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
98
JOSAM cam-aligner
2. Choose whether you want to align using the ‘Absolute’ or the ‘Relative’ method by clicking
99
JOSAM cam-aligner
Adjust to the desired value. The background color is grey when no tolerance is set for the
value to adjust, or red/green when a tolerance is set like on the example above.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
100
JOSAM cam-aligner
Adjust camber
Camber angles on front and rear axles can be adjusted in various ways. On vehicles with
certain adjustment possibilities, for instance vehicles with independent suspension,
adjustment can be easily monitored using the system.
2. Choose whether you want to align using the ‘Absolute’ or the ‘Relative’ method by clicking
101
JOSAM cam-aligner
Adjust to the desired value. The background color is grey when no tolerance is set for the
value to adjust, or red/green when a tolerance is set like on the example above.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
102
JOSAM cam-aligner
Specify on which axles the cameras are mounted. Click [Continue ] to proceed.
103
JOSAM cam-aligner
104
JOSAM cam-aligner
The straight ahead is the total position of the first axle calculated over the total toe value,
this means that the left wheel and the right wheel are running perfectly straight and parallel
to the centre line of the vehicle. Parallelism is also calculated over the total toe value of the
axles. Note: This is not a one-sided but a double-sided measurement, as all previously made
toe measurements from both sides of the vehicle are taken into account during the
calculations.
Adjust the drag link or track rod until the axles are parallel to each other. The background
color is grey when no tolerance is set for the value to adjust, or red/green when a tolerance
is set like on the example above.
Note! Make sure to have the first axle in straight ahead position while adjusting.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
105
JOSAM cam-aligner
Adjust caster
106
JOSAM cam-aligner
Adjust to the desired value. The background color is grey when no tolerance is set for the
value to adjust, or red/green when a tolerance is set like on the example above.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-03
107
JOSAM cam-aligner
Note! Make sure the steering gear is in the correct middle position mechanically.
2. Choose whether you want to align using the ‘Absolute’ or the ‘Relative’ method by clicking
108
JOSAM cam-aligner
Adjust the drag link in the direction applicable, to come to your desired value. The
background color is grey when no tolerance is set for the value to adjust, or red/green when
a tolerance is set like on the example above.
Click [Back ], or click [Save after adjustment ] to store the measurement results.
The program will then return to the “All values axle” measurement window. All measured
values will be displayed on the measured axle.
Updated 2015-03-02
109
JOSAM cam-aligner
Equipment calibration
Calibrate camera
The software has a built-in functionality for checking and calibrating the cameras. This
calibration is carried out on the vehicle to be measured, using the standard measurement
equipment.
If necessary, start up the unit itself by pressing the ON/OFF button on the back of the
camera.
111
JOSAM cam-aligner
Select [Camera ]
112
JOSAM cam-aligner
Follow the steps presented by the help texts in the grey square on the computer screen:
113
JOSAM cam-aligner
End turn the camera by taking it off of the wheel adapter spindle, turning it upside down and
putting it back on the wheel adapter spindle again. Aim the camera at the same marker and
press the OK button.
114
JOSAM cam-aligner
Updated 2015-01-12
115
JOSAM cam-aligner
Calibrate inclinometer
The software has a built-in functionality for calibrating the inclinometer. This calibration is
carried out on a stable stand, using the standard measurement equipment.
If necessary, start up the unit itself by pressing the ON/OFF button on the back of the
camera.
116
JOSAM cam-aligner
Select [Inclinometer ]
Follow the steps presented by the help texts in the gray square on the computer screen:
Mount the inclinometer unit in the inclinometer bar, as described in chapter "Measurement
preparations", section "Mount inclinometer unit".
Place or hang the inclinometer and its bar in a stable position. Click [Take value] to take a
first measurement.
End turn the inclinometer and its bar, put it back in the same stable position as in step 2, and
click [Take value] to take a second measurement.
117
JOSAM cam-aligner
The software has now saved the measurement values and calculated the calibration factor.
The inclinometer is calibrated and ready to use.
Note! After mounting or dismounting the inclinometer unit to the bar a calibration is
always necessary to ensure high measurement accuracy.
Updated 2015-01-12
118
JOSAM cam-aligner
System maintenance
Well kept and well maintained system parts will greatly increase and secure the reliability
and life time of the system.
Reflective targets
The reflective targets should be kept clean at all times. Clean them when necessary, or at
least once every third month, using a mixture of 50% alcohol and 50% water and dry them
with a soft cloth.
Please be aware that dirt, such as for example grease or oil, on the reflective wave will affect
the functionality of the system and might influence measurement results and/or the working
speed of the cameras. Therefore, be sure never to touch the reflective surfaces when
handling the targets.
Other equipment
Please check the functionality of all other hardware, like wheel adapters and frame gauges,
on regular basis in order to avoid faulty measurements.
Updated 2015-03-02
119
JOSAM cam-aligner
Measurement documentation
Order management
Enter the order management menu by pressing . Here you able to search for
previous created orders to continue measuring, view and print them.
You can use the search function to find previous orders, type a date interval or the
vehicle identification number this will reduce the amount of orders shown in the middle list.
121
JOSAM cam-aligner
The right side of the screen shows more information on the selected order, when ready
continue by pressing the next button to select the order and return to the start
menu.
Here you are also able to update the order information by pressing the edit button .
122
JOSAM cam-aligner
After pressing the edit button you can edit the data in the fields on the right side, when
ready save the changes using by pressing , or undo changes using cancel .
Updated 2015-03-06
123
JOSAM cam-aligner
Reports
Print the current order using the print button in the start menu.
Select the report type to print in the left list followed by clicking print button in the top
menu.
Depending on the system settings the system will either print a combined report sheet
showing both values ‘before adjustment’ and values ‘after measurement’ on the same
report, or separate report sheets showing the values ‘before adjustment’ and ‘after
adjustment’ respectively.
Updated 2015-03-06
124