FLUKE
70 Series
Multimeters
Service Manual
FLUKEFluke 70 Series
INPUT
SIGNAL,
siiiehs neon eke b
LCD
TO:
piairaL | |
oisecay |_|
+ RANGE &
aeecreenes sce: FUNCTION
AD CONTROL
pe ee my
COUNTER
U1 ANALOG. CHIP
A/D SAMPLES.
U2MICROCOMPUTER
Figured-t. Overiew =
Prot
Zi
oO
o—o- OHMS
So] VOLTAGE
> SOURCE
~S~o-—4
U1 ANALOG CHIP
oo ?
MA
Aree
Ans .
Jt Rt ape
[ae OFS
51
Rx a v2
: $
cou
22
Figure 3-2. Ohms FunctionoS Cm
Fluke 70 Series
3. Referring to Table 44, set the Decade Resistor
or Fluke 5100B to the resistance value indicated
in steps I through 6. Verify that the display
reading is within the limits shown,
To test the 73 meter, apply an input from the DC Voltage
Calibrator of +2V de to the V-Ohm and Common input
terminals of the UT. Verify that the display reading is
between +1960 and +2.040,
4-41. Diode Tost 4-12, DC mA Tost (75 & 77 Only)
‘Totest the 75 and 77 meters, perform the following steps: 1. Set the output of the DC Current Calibrator to
zero and connect itto the 300 mA and Common
L. Put the UUT in the Diode Test function input terminals of the UUT.
NOTE 2. Set the DC Current Calibrator to the output
shown in Table 4-5, and verify that the UUT.
On Fluke 5100 series calibrators, activate the display reading is within the limits shown,
50M divider override.
418, DC Amps Test
Set the DC Current Calibrator for zero output
and connect it to the 10A & Common input
terminals of the UUT.
2. Apply an input from the DC Voltage 1
Calibrator of +.090V dv to the V-Ohm and
Common input terminals of the UUT and
verify that the beeper is on,
2. Apply currents as indicated in Table 4-6 and
verify the display reading is within the limits
shown,
Increase the DC Voltage Calibrator output to
+.1L0V de and verify that the beeper is off
Table 4-2. AC Voltage Test
IneuT DISPLAY READING
sTEP. z
VOLTAGE FREQ 73 75 7
1 27V 400 Hz 2.617 102.783 2.644 to 2.786 2.644 to 2.756
2 27Vv 500 Hz 2.617 to 2.783 2.644 to 2.756 2.844 to 2.736
3 750V 100 Hz 725 10775 733 to 787 793 to 767
4 750V 1000 Hz 725 10.778 733 to 787 733 to 767
‘Table 4-3, OC Voltage Test
DISPLAY READING
step Dc INPUT
VOLTAGE By Zr 7 )
7 va7v 2.680 t0 2.720 2.885 1 2.715 2601 to 2.700
2 ZV 26.80 10 27.20 26.85 to 27.15, 28.81 to 27.09
3 +2109 268.0 t0 2720, 268.5 10 271.5 259.1 10270.9
4 +1000 991 to 1009 993 to 1007 1995 to 1005,
st +300 mV 297.8 to. 302.2 298.4 10 201.6 299.0 to 301.0,
“00mV function only
Table 4-4, Resistance Test
DISPLAY READING
ver INPUT DISPLAY AEs |
RESISTANCE Py oe "7
7 1000 988 to 101.2 98.1 to 1008 993 to 100.7
2 10090, 989 to 1011 1992 to 1008 ‘964 to 1096
a 10KA | a.80 te 10.11 9192 te 10.08 9.84 to 10.08
4 100 «a | 98.90 104.4 90.2 te 1008 99.4 101006 |
5 imo | 1989 {0 1.011 992 to 1.008 984 to 1.006
6 10 M0 | 262 to 1031 974 t0 10.26 3.79 19 10.21