INMecnH (CBEGS)
. Design of mechanicel sy 12-05-16
Sem- Vite Q. P. Code ; 729201
(3 Hours) [Total Marks : 80
NB: 1. Question No. 1 is compulsory
2. Solve any three questions trom remaining questions.
3, Assuime suitable data with proper justification if required,
4, Use of standard design data book like PSG, Kale and Khandare is permitted.
1. Answer any four of the following, 20
(a) What is morphology?
(b) Classity the wite ropes based on twisting of wires in a strand and state thei specific use
Explain seven phases of morphology
(c) Why cleaning of the belt is necessary for belt conveyor? List down the usual types of cleaners
(a) State the significance of specific speed and NPSH in the design of cexirifugal pump
(c) Explain why an [section with ly, <4 1 is selected for connectirg rod of LLC. engine
ions: 20
2. An EOT crane is to be designed for the following speci
Lifting capacity: 180 KN
Hoisting speed: 8 nvmin
Spat 10m |
Class. al
(4) Select suitable type and size of the ware rope to last fos about 12 months,
(ii) Select a standard hook and check for stresses indced at most critical section
(iu) Design the cross piece and side plates.
iv) Select a suitable motor for hoisting mechanism,
3
(a) A 20° troughing belt conveyer as the following speciticat 1s
Material to be conveyed : lirte stone
Maximum tump size. 100 mm
Capacity 2300 TPH
Inclination 100
Centre distanes 260m
(i) Determine the width, number of plies and the thickness of the belt
ii) Select a proper motor for the conveyor
(ii) Design the drive pulley along with its shatt and also select its bearings
s
(¢} Explain system concepts in design with suttable examples,
[TurnoverQ.4 A single cylinder four stroke cycle diesel engine develops 12 kW brake power
when operating at 1000 rpm. Design ine following components: 2»
(i) Determine bore and stroke of the engine.
(11) Design cylinder head and wet liner
(iti) Design piston, prston rings and piston pin.
(iy) Selecting material and design stresses, determine cross-section of the connecting rd
Q.$ Design a centrifugal pump (with layout) for the following specitications 20
Static suction head: 3m
Length of suction pipe » 10m
Static delivery head: 201m
Length of delivery pipe | 35 m
Discharge + 3000 pm
Fluid to be pumped is water at room temperature, Desigii should include selection of
motor, design of impellcr, impeller shaft, volute casing.
Q6.
(a) 1s required 19 design year pump for How of $0 LPM and pressure 90 bar, 0
The pump 1s ta_be driven trom an electric motor by direct coupling. The desig should inelue ths
design of gears. driver shaft and its bearings,
(b) A three-stage, twelve speed gear box 1s to he designed for spindle speeds varying between
50 rpm. and 3000 r-p.m. ‘The second stage consists of three speed steps. If the gear bos is
driven by 7.5 KW, 1440 rpm, :dectric motor 10
(i) draw the speed diagram and
(ii) draw the gearing diaysam,
Assume same module for all gears,‘Course : 8 E,(Mechanical) (Sem Vill) (CBSGS) (Prog-T8328)
QP Code: 729201
Correction:
@. 3 tad
Read As:
Inclination 10°
Instead of:
Inclination 100
Date and Time 12/05/2016 11:50 AM
sthypi amMd.com