Professional Documents
Culture Documents
1.manual Pss 21h 2z18 b4
1.manual Pss 21h 2z18 b4
1.manual Pss 21h 2z18 b4
Product Specifications
PSS 21H-2Z18 B4
The FBM218 offers redundant modules for eight output channels, each providing a 4 to 20mA output signal
or a digital HART® signal superimposed on a 4 to 20 mA analog output signal.
FOXBORO®
Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com
PSS 21H-2Z18 B4
Page 2
To/from
Intelligent
Field Devices
EASY REMOVAL/REPLACEMENT
The module can be removed/replaced without
removing field device termination cabling, power, or
communications cabling.
F U N C T I O N A L S P E C I F I C AT I O N S
(1) The maximum allowable distance decreases when the loop is operated through an intrinsic safety barrier. The maximum distance of
the field device from the FBM is a function of compliance voltage (19 V dc at 20.4 mA), wire and load resistance, and voltage drop at
the field device.
F U N C T I O N A L S PE CI F I C AT I O N S ( C O N T I N U E D )
E N V I R O N M E N TA L S P E C I F I C AT I O N S ( 2 )
Operating Storage
TEMPERATURE TEMPERATURE
Module -40 to +70°C (-40 to +158°F)
-20 to +70°C (-4 to +158°F) RELATIVE HUMIDITY
Termination Assembly 5 to 95% (noncondensing)
PVC ALTITUDE
-20 to +50°C (-4 to +122°F) -300 to +12,000 m (-1,000 to +40,000 ft)
RELATIVE HUMIDITY
Contamination
5 to 95% (noncondensing)
Suitable for use in Class G3 (Harsh) environments as
ALTITUDE defined in ISA Standard S71.04, based on exposure
-300 to +3,000 m (-1,000 to +10,000 ft) testing according to EIA Standard 364-65, Class III.
Vibration
7.5 m/S2 (0.75 g) from 5 to 500 Hz
(2) The environmental limits of this module may be enhanced by the type of enclosure containing the module. Refer to the applicable
Product Specification Sheet (PSS) which describes the specific type of enclosure that is to be used.
P H Y S I C A L S P E C I F I C AT I O N S
TERMINATION ASSEMBLIES AND CABLES A removable termination cable connects the DIN rail
Field output signals connect to the FBM subsystem mounted TA to the FBM via a field connector on the
via DIN rail mounted Termination Assemblies, which baseplate in which the FBM is installed. Termination
are electrically passive. TAs for the FBM218 are cables are available in the following materials:
available in the following forms: Polyurethane
F U N C T I O N A L S P E C I F I C AT I ON S – T E R M I N AT I O N A S S E M B L I E S
TA Part TA Part TA
Number Number Termination TA Cable Certification
Type Certification(a)
Type 1 TAs are UL/UL-C listed as suitable for use in Class I; Groups A-D; Division 2 temperature code
T4 hazardous locations. They are CENELEC (DEMKO) certified EEx nA IIC T4 for use in Zone 2
potentially explosive atmospheres.
Type 2 TAs are UL/UL-C listed as associated apparatus for supplying non-incendive field circuits
Class I; Groups A-D; Division 2 hazardous locations when connected to specified DIN rail
mounted FBMs and field circuits meeting entity parameter constraints specified in DIN Rail
Mounted Subsystem User’s Guide (B0400FA). They are also CENELEC (DEMKO) certified as
associated apparatus for supplying field circuits for Group IIC, Zone 2 potentially explosive
atmospheres. Field circuits are also Class 2 limited energy (60 V dc, 30 V ac, 100 VA or less) if
customer-supplied equipment meets Class 2 limits.
(a) All TAs are UL/UL-C listed to comply with applicable ordinary location safety standards for fire and shock hazards. Hazardous location
types comply with ATEX directive for II 3 G use. They also comply with the requirements of the European Low Voltage Directive. All
listings/certifications require installation and use within the constraints specified in DIN Rail Mounted Subsystem User’s Guide
(B0400FA) and the conditions stated in UL and DEMKO reports.
DIMENSIONS – NOMINAL
[72] (b)
[80] 2.83
3.13
[72] (b)
[80] 2.83
3.13
R E L AT E D P R O DU C T S P E C I F I C AT I O N S H E E T S
IPS Corporate Headquarters Invensys, Foxboro, I/A Series and the IPS Logo are
5601 Granite Parkway Suite 1000 trademarks of Invensys plc, its subsidiaries, and affiliates.
Plano, TX 75024 All other brand names may be trademarks of their
United States of America respective owners.
www.ips.invensys.com