olment Nox [P| | CC
_
§. V.NATIONAL INSTITUTE OF TE SHNOLOGY, SURAI
M. TECH, (CAD-CAM), SEMESTER IT
Subject code and name: ME! 764, Computer Aided Manufacturing
END SEMESTER EXAMINATION (May 2018)
ime: 3 hours Max. Marks: 100
ris]
{iaplain how pattering ca be done for an fern in regular and icregular interval?
explain with figure various surfaces with Fespeet to CADP, Write the meaning of
TO, ON and PAST with respeet to surfac
Explain use of RETAIN, OMIT and AVC |
Slate and explain the difierence between fixed sequential Format and tab sequential formal |
What iffaront between GO statement used in point to point motion eorimands and
icontinuous path motion commands? explain with suitable example. What is the meaning!
lof INDIRP? \
[plain right hand thumb rule for desige
sketch,
the following, : (CO2, CO3) [303
‘fon Tor the object shown below. |
i ]
Pl bee 1
| | |
' I | “e 1
1 | i | 14
i 1 |
i WE \ 5
\ i | t | |
if L \ | y |
i ; | |
tL. | Lt
jx 45 7 s0> Le 60-») |
eee o aa Fig.l.
(Billet size 144 nm x 201 mm
|Assume suitable speed and feed and follow Magic ~ 3 code and word address format, Takel
{nose radius of the tool as zero. : HEE
Page Lot 4(B) |W
| z
feed rate ~ 7.5 aum/niin and spindle speed = 900 rpm
) |List the tool-lengih set-up you know. Explain any one in bi
'|Why servo motor is used in’ production CNC machine tool? What is the main!
APT part program for machining a part as shown in Fi
mild steel and cut
2. The workpiece is
s diameter is 6.5 mn
he requited machining parameters ave
“|
aN
AL ote}
a fo-2eeer
i
re 4
\
Feapsl :
Answer (he following: (CO2, CO3, C
4) [35]
Draw the CIM wheel, Explain its components
(Gi) Define geometry commands for circle, tangent to a line, a point on the circumference|
and radius,
eometry commands for point, due to intersection of two circles
iv) Define geometry commands for a plate, passing from point and paallel to}
another plane, |
¥y) Define geometry commands for circle, tangential to fine and cirele, and radius
a cm Mlexibilities and their measures,
Section 11
Using neat sketch explain G73 cycle.
State the four advantages of using ball-screw in CNC milling machine.
reason that AC servo motor is preferred over DC servo motor?
Using neat sketch explain’
mode,
ervo
8 command with absolute mode and incremental
Page LordeB)
n
Answer any THREE questions, (C02) {30
Write a CNC part program for Fanue controller to mill circular pocket without)
using cutter radius offset commends having depth 2 mm (Fig. 1, LEP). The cutter,
liameter is 10 mm, cutting speed is 50 m/min and feed rate is 0,05 mmirev. Stari
form the cenire and step over is 25%,
OR
Write @ CNC part program for Fanuc controller to mill square pocket without using]
cutter sadius offset commands having depth 2 mm (Big. 1, RIGHT). The cutter
diameter is 8 mm, cutting speed is 50 m/min and feed rate is 0.05 mm/rev. Use zig,
‘zag tool path and step over is 75% -
Write a CNC patt program for external contour of regular pentagon of 100 mm side (Fig.
2) using mirror and subroutine commands, Select appropriate work zero, Cutter diameter is|
20 mm, cutting speed is 40 nw/iin and feed tate is 40 rany/nin,
Write a CNC part program (Pantic Control) to drill the hole patterns as shown in]
(Fig. 3 using standard peck drilling eyele, The plate thickness is 50 mm. Refer
following data and information:
Cutting speed is 40 m/min and feed rate is 40 mina, and Revel is 2. mm, Write]
the brief comment beside eack
Write « CNC program (Fanuc Control) to mae!
jas shown in Fig. 4, You ean w
ine the boundary of the component
the part program with or without using culte:
hadius offset commands. Program clockwise from the work zero and shove
ccaleutations for tool path coordinates.
End-mill cutter diameter = 8 mm, maximum end mill cutter diameter ean be used as}
20 mm, thickness of workpiece is 10 mm, fed rate is 30 mrafmin and eutting spoed
ent b bloc
ice eam
{ se :
form
Page 3 of 4