Professional Documents
Culture Documents
Energy Auditing
Energy Auditing
Energy Audit/Assessment
• First step in identification and implementation of various energy
efficiency opportunities in residential, commercial, institutional and
industrial facilities.
• The objective is to identify economical energy/cost saving measures
that do not adversely affect the quality of work/product and the
environmental consequences of the equipment and processes.
• Energy audit is a needed step in implementation of any detailed and
sizable energy efficiency project. Often there will be the need for
engineering design before implementation/ construction of the
project.
• The major impetus behind an energy audit is that the analysis of
energy consumption and identification of potential conservation
measures in facilities relate to various disciplines of engineering, that
are often beyond the expertise of one person or small engineering
firms.
2 Dr Nadeem Feroze
Energy Audit
4 Dr Nadeem Feroze
Walk-through Audits
Done by utility representatives or equipment
vendors
5 Dr Nadeem Feroze
Walk Through Audit Common Tools
Clipboard
Flashlight
Camera
Light Meter
Screwdrivers
True RMS meter
Amp Meter.
6 Dr Nadeem Feroze
Major Focus of Walk through Audits
Lighting Systems
Steam Systems
Motors, Belts and Drives
Refrigeration Systems
Hydraulic Systems
Fans and Pumps
Compressed Air Systems
Injection Molding or Extrusion
Dryers
7 Dr Nadeem Feroze
Lighting Systems
Use binoculars to identify high bay lights
Check with stockroom to identify type of light
Light output is measured in lumens
Lumens/watts is the ratio of the amount of light
produced per the energy input-Criteria for energy
The amount of light available at a particular location is
measured in foot-candles by hand held meters
8 Dr Nadeem Feroze
9 Dr Nadeem Feroze
Lighting System
Are lights on in unoccupied area?
Is the exterior light on during the day?
Manually turn off lights-simplest
Although reliability depends on reliability of operator
Install occupancy sensor or photoelectric sensors
More reliable
Applications (Pump houses, meeting rooms, bathrooms, warehouse,
storage area, street lights)
Replace high Pressure sodium (HPS) lights in low use areas with
fluorescent lights for quick on and off control
HPS cheaper for long running but warming up time for low use areas is an
issue
Replace or maintain faulty controls
10 Dr Nadeem Feroze
Lighting System
Are existing lighting levels higher than the recommended levels?
Use hand held meter to check light level
Remove excessive lighting
Reduce overall lighting and install task lighting
11 Dr Nadeem Feroze
Motors, Belts and Drives
12 Dr Nadeem Feroze
Motor, Belts and Drives
13 Dr Nadeem Feroze
Motors, Belts and Drives
Are standard efficiency motors installed?
Replace motors with high efficiency motors
14 Dr Nadeem Feroze
Motors, Belts and Drives
15 Dr Nadeem Feroze
Motors, Belts and Drives
Does the facility utilize DC generator sets to provide variable
speed control of equipment?
Replace generator sets with solid-state variable speed drives
25% Increase in overall efficiency
Does the facility utilize Eddy Current drives variable speed
control?
Eddy Current drives less efficient replace with solid sate
variable speed drives
Maintenance costs are high
Are motors installed that operate continuously at part load?
16 Dr Nadeem Feroze
17 Dr Nadeem Feroze
Fans and Pumps
Are pumps or fans installed that are not sized correctly for the task?
Reduce pump or fan speed using a sheave adjustment or motor
replacement
Trim or replace pump impellers
Replace fan or pump with a more energy efficient model
Does the facility have a cooling tower?
Install solid state VSD control on the cooling fans
More fan speed requirement in day compared to night
Replace the tower fill material with cellular film fill to improve heat
transfer efficiency
Install non-clogging, non-corroding spray nozzle to improve water
distribution through the tower
Install energy efficient airfoil fans
Install energy efficient motors on the cooling tower fans and pumps
18 Dr Nadeem Feroze
Fans and Pumps
Are pumps or fans being throttled in order to control the flow
rate?
Is bypass control being utilized to vary the flow out of the Pump?
19 Dr Nadeem Feroze
Compressed Air Systems
Are large compressors serving minimal system needs during off-
hours such as maintaining the minimum pressure requirements for
a Dry Fire Suppression System?
Install smaller air compressor dedicated to serve minimal after hour
needs, and isolate from main plant air system
Does the facility have Centrifugal Screw Compressors that operate
at less than full load capacity for than 70 percent of the Time?
Is throttle control used to modulate the compressor output
capacity?
Replace throttle control with Load-Unload (on-off) controls
Throttle must be used when operating at more than 80% Capacity
Throttle creates vacuum at compressor inlet when required in batches hence
operation is lowered in capacity when the pressure is reduced
20 Dr Nadeem Feroze
Compressed Air Systems
Does the facility have more than one compressor feeding into a common
header? Are the compressors operating at less than full output capacity?
Sequence multiple compressors for proper control
Are compressors operating at zero capacity for extended periods of
time?
Shut off compressors during such times
Is the discharge pressure of the compressor higher than 110 psig?
80 psig is common operating pressure
90-110 psig considered higher range,
power increase by 0.5% for each psi
Chances of air leakage higher for higher pressures
Needed for delivery of air even to remote locations in the plant
Introduce looped piping
Install large pipes
Is high pressure air being used for tanks that do not require high pressure
air?
21 Dr Nadeem Feroze
Compressed Air Systems
Does the compressed air system have significant air leaks?
Leaks are easiest to find when the plant is quite
To quantify total air leaks in a plant: note down air compressor
loading and/or air delivery during breaks
Ultrasonic tools provide most reliable method to locate air leaks
Common leak locations: valve packing, pneumatic cylinders and
hoses,
Air leaks exceeding 35% of the air used are excessive in any plant
Is the pressure drop across auxiliary equipment such as dryers, oil
separators or filters excessive?
Replace filters, overhaul equipment to reduce pressure drop
Size equipment to accommodate air flow with acceptable pressure
drop
Is compressed air the best utility for the given application?
Replace pneumatic motor with an electric motor
22 Dr Nadeem Feroze
Steam Systems
23 Dr Nadeem Feroze
Steam System
Is the boiler operating at incomplete combustion?
Tune the Boiler
Is the condensate return system open to atmosphere?
Install properly designed steam traps to reduce the amount of steam
lost through the open system
Install pressurized condensate return system to reduce flash steam
losses
Insulate condensate storage tanks
Is the efficiency and performance of the steam system being
monitored manually?
Is the flow rate of the induced draft and forced draft fans being
controlled by throttling methods?
Are there any opportunities for heat recovery?
24 Dr Nadeem Feroze
Refrigeration Systems
25 Dr Nadeem Feroze
Refrigeration Systems
Optimize the refrigeration system
Optimize inter-stage pressure
A two stage system has three separate pressures maintained by high and low stage
compressors. Choose intermediate pressure so that each compressor has approximately the
same pressure ratio to minimize compressor energy use.
Economized single stage system
For applications that require extremely low temperatures such as a blast freezer, a two-stage
compressor is usually preferred. An “economized” single stage system may allow operation at
slightly lower suction temperatures while providing the necessary cooling and avoiding the
cost of a two-stage system.
Install 2-speed or VSD speed control on condenser and evaporator fans
By reducing fan speed when full capacity is not needed, the energy consumption of the fan
motors is significantly reduced
Cycle evaporator and condenser fans
Evaporate fans move air across refrigerant coils to condition the space. Condenser fans
remove the heat generated during compression of the refrigerant. Evaporator fans can turn
off when not needed for temperature control. Cycling fans saves fan and compressor energy.
Duty cycles can be reduced as much as 50 percent. A timer can be used to cycle primary fans
after a given amount of operation.
26 Dr Nadeem Feroze
Refrigeration Systems
Install computer or “semi-automatic” controls to allow the compressors to
operate at their highest efficiency
Overlap suction pressure switches on compressors connected to a common
header to allow their operation to be sequenced
Poor cooler/freezer insulation, undersized or dirty evaporators require
lower suction pressure and wastes energy
Consolidate and re-pipe loads with similar suction requirements. Dedicate a
compressor to these loads
Compressor operating at maximum suction pressure are more energy efficient
Reset suction pressure
Raise suction pressure to match the actual pressure required to meet the cooling loads.
When the suction pressure drop increases, compressor work increases.
Add evaporator capacity to reduce evaporator approach temperature and raise
suction pressure
The compressor savings resulting from operating at higher suction pressure often offset the
additional evaporator fan energy consumed
27 Dr Nadeem Feroze
Walk-Through Audit
1° Step
Meeting with the appropriate plant personnel that are familiar with the
physical condition and day-to-day operation of the manufacturing equipment
Determine which of the systems, technologies, and equipment needs energy
optimization
2° Step
Go through the checklist of questions in a guide that pertain to the facility
All of these questions may not be answered in the meeting and, therefore,
should be “flagged” to be addressed during the walk-through.
As you go through the checklist of questions, discuss any concerns that the
plant personnel may have with implementing the energy saving measures
Determine the energy savings measures that have already been implemented
and those that may or may not be applicable
28
Dr Nadeem Feroze
Walk Through Audit
3° Step
The next step is to tour the facility with the appropriate plant personnel that
are familiar with the various areas that you will be auditing.
As you tour the facility, refer to the questionnaire to ensure that you answer
any remaining checklist questions.
Record observations, such as equipment name plate data, gauge readings,
meter readings, and to make notes, such as areas that require further study,
equipment operators names, phone numbers, etc.
4° Step
After the tour is completed, a wrap up meeting should be held to review
your findings.
At this point, a list of potential energy saving opportunities that should be
considered for additional study can be developed.
29 Dr Nadeem Feroze
Investment Grade Audits
A detailed or investment grade audit (whether comprehensive or targeted) is a
technical and economic analysis of potential energy saving projects in a facility that:
Provides information on current energy consuming equipment operations
Identifies technically and economically feasible energy efficiency improvements for
existing equipment, and process
Provides the customer with sufficient information to judge the technical and
economic feasibility of the recommended projects.
Basis for further engineering analysis and design, and investment in energy efficiency
improvements by facility owners or third parties.
Can be also the basis for performance contract agreements.
An accurate audit can result in identification of highly cost effective projects, and
result in substantial cost/time savings in realization of the projects, while a low
quality audit will result in unrealistic savings analysis, duplicate work in the
engineering design process, and potential problems in performance contract
agreements.
30 Dr Nadeem Feroze
Expectations from Investment Grade Audit
Clear operating hours per department (and equipment in the case of major energy
users)
Clear inventory of energy consuming equipment including their nominal ratings and
capacities
Energy rate/cost per unit of energy usage and for different types of energy
Analysis of at least one year of energy consumption by type of energy/fuel
Energy balance of the plant per type of fuel and preferably per meter based on rating,
operating hour, utility factor and load factor of equipment. Utility factor is the ratio
of the operating hours of an equipment to the total operating hours of department.
Load factor is the ratio of the actual draw of equipment to the nominal rating of
equipment
Clear identification of major energy consuming processes and equipment in the whole
facility
Analysis of major energy efficiency measures including source of energy saving,
amount and type of energy saved, cost savings, implementation cost and a pay-back
analysis
Clear identification of the retrofit or control scheme/technology, and inclusion of cut
sheets of the proposed equipment
Clear identification of the measures that may have potential in similar facilities that do
31 not exist or areFeroze
Dr Nadeem not economical in the audited facility
Investment Grade Audit- Major Concern
32 Dr Nadeem Feroze
Investment Grade Audit Checklist
Are the energy rates based on historical (or projected) energy consumption and
current (or projected) energy rates?
• Has energy usage (and demand in the case of large electricity users) been balanced
for at least one full year of energy data, separately for different fuels and preferably
per meter? The preferred forms of presentation is graphical (e.g. pie chart) or
tabular.
• Are operating hours for different areas in the facility clearly identified and taken into
consideration?
• Are major energy consumers clearly identified, and taken into consideration in the
energy balance?
• Are the bases for implementation costs clearly identified?
• If a modeling software has been used, are the inputs and outputs clearly identified, so
that another expert can repeat the work?
33 Dr Nadeem Feroze
Investment Grade Audit Checklist
• For the proposed measures, is it clear why energy will be saved?
• Is it clear what form of retrofit is proposed and what are the advantages?
• Is it clear where the retrofit should take place?
• Have all potential energy efficiency measures been addressed?
• Lack of consistency in energy cost, demand cost, operating hours of various
area of the facilities; often the basis for the considered demand cost is not
clear
• Lack of energy balance, which often results in overestimation of the cost
savings
• Lack of a clear description of the energy rate schedules, annual energy
analysis, so that the customer is not really provided with a clear picture of
how they are charged.
34 Dr Nadeem Feroze
Investment Grade Audits
Be Careful!!!!!
a low quality audit will result in unrealistic savings analysis, duplicate work in the
engineering design process, and potential problems in performance contract
agreements.
And….
More importantly, because some of these energy audits may become a basis for
investment in, and establishment of distributed generation facilities in the
present energy market, energy audit work may have significant economic
repercussions.
35 Dr Nadeem Feroze
Energy Audit Report
• Executive Summary • Utility rate structures
• A brief summary of the recommendations and • Tables and graphs of energy consumptions and
cost savings costs
• Table of Contents • Discussion of energy costs and energy bills
37 Dr Nadeem Feroze
Causes of Deficiencies in Audit Reports
Lack of expertise of people who do the surveys, and more importantly
those who prepare the report
Lack of basic knowledge of the fundamental engineering principles.
Energy efficiency work is multidisciplinary, which necessitates a strong
knowledge of fundamentals of mechanical and electrical engineering.
Lack of training in application of sophisticated simulation software.
Conflict of interest
An example is when a firm is hired to do a comprehensive energy audit,
but fails to take inventory of all equipment and evaluate them, in the
interest of an attractive lighting retrofit project. Other examples are
consideration of unrealistic operating hours, utility factors, load factors of
the equipment. An oversized 50 hp fan motor may operate at 50% of its
load, but it will not be known in the plant audit if its power draw is not
measured!
38
Dr Nadeem Feroze
COMPLICATED ENERGY AUDIT CASES
39 Dr Nadeem Feroze
Issues in Audit of Manufacturing Facilities
A much wider scope of measures and advanced technologies (inclusive of
those for commercial facilities) can be identified in industrial facilities.
While there are significant commonalties between industrial facilities
with different processes, most facilities may have their unique energy
efficiency measures that can be identified and analyzed based on
fundamental engineering principles.
Load measurements are required for major energy consuming devices.
Some equipment may go through significant load variations.
Energy usage in most industrial facilities are highly product and
production dependent, and much less dependent on ambient conditions.
Taking a detailed inventory (which includes the rating, usage pattern,
loading) of energy consuming equipment is an essential component of a
comprehensive energy audit of industrial facilities.
40 Dr Nadeem Feroze
Energy Audit Case Studies
Audit Measures Recommended Issues Raised
Office Building Retrofit part of the lighting system Type of lamps and fixtures not identified, energy
Firm A HVAC system upgrade savings overestimated by about 40%
HVAC system energy savings overestimated by about
50% (methodology problem)
Various measures not identified:
•VFD* for chilled water and condenser pumps
•VFD for cooling tower fans
•VFD for return fans
•Proper control of supply fan VFD
•Various control issues
Office Building Installation of a New 400 Ton Variable Speed Chiller No energy or demand balance presented
Upgrade Existing Partial Thermal Energy Storage Utility rate schedules were not identified
Firm B System DOE-2 simulation had been used but no input/output
Install VSD* on Pumps and Fans data were presented
Energy Management Hardware and Software It is not clear how cooling tower fans are controlled
Retrofit Lighting
Office Building Installation of VFDs on the Supply and return Fans. Measured power of the motors is based on current
Firm A Installation of CO2 Controls on the Return Air Fans. measurement, lacks power factor measurement
Installation of Damper Control. Fan curves have been used for VFD justification, not
clear if flow and pressure were measured or assumed,
fan curves are sensitive to both
Numerical errors in power savings calculations
resulted in overestimation of savings by 50%
It is not clear why installation of CO2 sensors are
recommended and how it will result in any energy
savings, maintenance cost savings, etc.
Automating the on/off of the HVAC system not
41 Dr Nadeem Feroze identified, while it is done manually now
Energy Audit Case Studies
Audit Measures Recommended Issues Raised
Office Building Lighting Retrofit The schedule of operation of HVAC system and
Firm D EMS Controls Modifications building temperature control (chillers included)
VSD’s for Pumps and Chillers are not clear.
Window Film The specs for the HVAC system are not provided.
Thermal Energy Storage The DOE-2 simulation has not been properly
calibrated. There is a discrepancy of upto 50% in
42 Dr Nadeem Feroze demand estimation
Implementing the Audit Recommendations
43 Dr Nadeem Feroze
This is NOT a sunset! This is a sunrise!
You have to get up early, there’s a lot to do!