Professional Documents
Culture Documents
Zonton 999 PDF
Zonton 999 PDF
999 Professional
FM Transceiver
Channel Mode and Frequency+Channe The transmitting will stop when The voltage of battery is
the red indicator flashes and "Du" too low. Please charge at
Mode. [FUNC](1 second)+[C]
Copy Channel 26 sounds once!
Rotate[Circumrotate Encoder] to
choose channel, press PIT to save. Out of lock, programmed
"Da da" sounds at intervals. frequency is out of the
Frequency Mode. range of the transceiver.
[FUNC] (1 second)+[C].
Save Channel 27 The transmitting(last a little while) TOT alert is ON.
Rotate [ Circumrotate Encoder] to
will stop when hear "Du" sounds Release PIT to stop the
choose channel, press PTT to save. from speaker. alert tone.
Channel Mode and Frequency+Channel The transmitting(last a little while)
Mode. [FUNC](1 second)+[D]. Rotate will stop when hear a prompting TOT alert is ON.
Delete Channel 27
[Circumrotate Encoder] to choose voice.
delete channel, press PIT to exit. Set Interval after TOT or
The transceiver transmits after a TOT resume time. After
Press[lOW]+[MONI]+Power ON at the
Copy Function with while of the TOT alerts. limited time the transce-
same time. Press [MONI] to transmit 28 iver can transmit.
Cable
data,then exit to power off and reboot.
When receive signal from other
transceiver,the green light ON.
Press PIT to transmit and "Du" BCl function is ON.
sounds heard,then retum to receive
signal.
PRECAUTION CONTENT
For using this transceiver with high safety and efficiency, please Unpacking and Checking Equipment·····--------------- 1
Supplied Accessories • - -. - ••• - - - - - - - -. - - - - - - - -. - - - - - 1
read the following information carefully:
Standard Accessories • - - - - - - - - - - - - - - - ••• -. - - •• - - -. - - 2
1. Repairing is only for qualified technicians. Please do not dis-
Optional Accessories • - - - - - - - - - - - - - - - - ••••• - -. - - - - - - 2
assemble the transceiver causally.
Battery - - - - - - - - - - - .. - - - - .. - - - - .. - - - - - - - - . - - - - - - . - . - ... - 3
2. Do not modify the transceiver causally. Notes •••• - •••• - ••• - •• - - - - -. - - - - - -. - _. - _•• _•• -. -. - - 3
3. Power off when enter into the flammable and explosive places. How to Charge - .... - - - - - - - - - - - - - - - -. - - - - _. - - - -. - - - - - - - 4
4. Please do not change or charge the battery when under the How to Store - -- -- -- - -- - - -- --- •- -•- •- -- -- - - --- --- - - .4
flammable and explosive circumstances. Installing the Accessories . -. - - - - - - - - - - - -. - - - - - - - .... 5. 7
5. Please power OFF the transceiver before entering the explosive Installing/Removing the Battery - - - - -. - - - •• - - - -. -. -. - -. 5
and detonators areas. Installing/Removing the Antenna - •• -. -. - - -. - - - - -. - - - - - 6
6. To avoid the problem caused by electromagnetism interfering Installing/Removing the Belt Clip - - - - - - - •••• - - - •••••• _. 6
or compatibility,please power OFF when you entering into Installing/Removing the Gallus - - - - - - - - - - - - - •••• - - - - - - 7
Installing Exterior Earphone/Microphone - - - - - - - - - - - - - -·7
the places where is not allowed to use the transceiver,such
Getting Acquainted - - - - - - - ... - ... - - - - - - -. -. - - - -. - . - 8. 11
as hospitals and airplanes.
LED Screen • -. - - - - - - - - - - - - - - • -. - - - - - - - - •• _. - - - - - 11
7. Please put the device out of the range of the extension of the
Basic Operation - - - - - - - - - - - - - - - - - .• _. - •. - - - - - - - - -. 12, 16
airbag in the car. Power ON/OFF - - - • - - ••• -. - •• - - - - - - - - -. - - - - - - - •• -. - 12
8. Do not expose the transceiver under sunshine for a long Volume Control-· - ••••• - - - - - - - - - - - - - - -. _. -. - _••• - - - 12
time,nor place it close to heating appliances. Choose Displaying Mode - - _••• - - - - - - -. - - - - - - - - - - - - 12
9. Please keep the antenna at least 2.5cm far away from you Choose Channel - - - - - _•• - -. - - - - - - - - - - - - - - - - - - - _. - - 13
Choose Frequency ------------ ••• - ••• ------------- 13
when transmitting.
Squelch - - - - - - • -. - - - - •••• -. _•• - - - - - - -. - ••• - • -. - - - - 14
10.00 not put the device into the dusty,humid and wet areas, nor
Transmitting' - - - - - -- - - - - - - - - - - - -. -. - --- - - -- -. - - - - - 15
put it into the rough surface. Receiving - - - - - - - - - - - - -. - - _•••• - - - - - -. - - - - - - - - - - - - 15
11.lf the device smelled abnormally or smoking,please power High/Low Power - - - _. - - - - - - - - - - - - - - - - -. - • - _•• _. - - - 16
OFF at once,and take out the battery, then contact with the Advanced Operation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17 28
local distributor. Add Scanning Channel·· - - _•• - - - - - - - - -. - - - - - - - -. - • .' 17
Channel Scanning _. -. _. - - - - - -. - - - - - -. _•• - - -. - •• - -. 17
.CONTENT
Frequency Scanning -. - - - - - - - - - - - - - - - - -. - - - - - - -. - - 18 Carefully unpack the transceiver. We suggest that you confirm the
DTMF Calling ---- •• -------.------ •••• -----.-.- 19, 21 items listed in the following table before discarding the packing
Key Locked - - • - - - - - - • - • - - - - - - •• - - - - - - - • - - - - - - - •• - 21 material. If any items are missing or have been damaged during
Lightening - - - - - - - - •• - - - - - •• - - - - - ••••• - - - - - - •• - - - - 21
shipment, contact with the dealer immediately.
Reverse Frequency - - - - • -. - • - - - - - ••• - - •• - - •• - - - - - -. 22
Stepping .-.------ ••• ------.------ •• --------.----- 22
VOX - -. - - - - - ••• -. - - - - - - •• - -- - - ••• -- - -. -.-. -- - - - - 23
CTCSS/DCS - •• - - - - -. -. - - -. -. -. -. - - - - -. - - - - - -. 23, 25
Slip Frequency. - - - - -. - - - - - •• - -. - - - - ••• - - - - - - •• - - -. 25 ITEM QUA!JTiiY?0) l;h
Wide/Narrow Band - - -. - •• -. - - - - -. - - - - - - - •• - - - - - - •• 26 136-174MHz
Copy Channel - - - - - -. - - - - - -. -. - - - - - - - •• - - - - - -. - - - - 26 Antenna 350-390MHz 1
Save Channel - - ••• -. - - - -. - - - - - - -. -. - - - - - - - - - - - - - -. 27 400-470MHz etc.
Delete Channel -. -. - - • - •• - - - - - - -. - - - - - - - -. - - - - •• -. 27 Li·ion Battery Charger 1
Copy Function with Cable - -. - - - - - - •• - - - - - - ••• - - - - - - 28
Adaptor 1
Auxiliary Operation - - -. - - - - - - - •. - - - - - - -. - - - - - - -. 29, 31
Time-out Timer - - - - - - •• - - -. - -. - ••• - - - - - •• - - - -. -. - •. 29 Li-ion Battery (7.4V 1100mAh) 1
TOT Pre-caution Time - - - - - - - - - - - - - -. -. - - - -. -. - - - - -. 29 Gallus 1
Interval after TOT - - - - • - - -. - - ••••• - - - - - -. - - - - -. - - - - 29
Belt Clip 1
TOT Resume Time·· - - - - - -. -. - - - - - - - - - - - •• - •• - - - -. 29
MONI Key Setting ------.-.-------.----- •• -------.- 29 Screws 1
Busy Channel Lokced • - - - - - - - _. - - - - - - -. - - - - - -. - - - - 30 Instruction Manual 1
Battery Save - - - ••••• - - - - - • - - - - - - - - - - - - - - - •• - - - • - -. 30
Prompting Voice - - - - ••• - - - - - - - ••• - - - - - -. - - - - - • -. - -. 30
Low Battery Warning -. - - - - - - ••• - - - - -. - •• - - - - - •• - - - - 30
PTT 10 -. - - - -- --. -- - --- --- - .-- -- .:- - - --.-. -. -- --. - 31
Input Information - - - - -. - - - - - ••• -. - - - - •• - - - - - - -. - - - -. 31
Main Technology Parameter··------·-------·--- 32, 33
Trouble Shooting - •.•• ----- •.• ---- •. - .• --- .• --- 34, 35
BATTERY
Please charge the battery before you use it,because it was uncharged
against delivery. The first charging after purchasing or keeping for more
than 2 months without using cannot achieve normal battery capacity.
After repeating the charge/discharge for 2 or 3 times, the battery can get
to the best performance Please change or charge the battery if low power.
o
1. Please use the specific charger, other models may cause explosion
and lead to hurt the body.
2. Do not short circuit the battery or put it into fire,nor remove the housing
of the battery.
Instruction
Manual 3. The ambient temperature should between 5"C and 40"C while charging.
Otherwise, it may not fUlly charge.
4. Power OFF the transceiver with battery while charging. Using the devic
while charging would affect normal charging.
5. To avoid interfering the charging, please do not cut off the power or take
out the battery during charging.
~ 6. The battery life will over soon when its operating time decreases even
~ ~
Speaker/Mic Speaker/Mic though it is fully and correctly charged. Please replace the battery.
Headset
(QME-01) (QME-02) 7. Please do not take out the battery and recharge it after it was fully
charged,otherwise the battery would be damaged or the life would be
shorten.
®~
~ ,~ ~
\ .'/
~ 8. Please do not charge when the battery or the transceiver is damped.
Programming Do it before wipe it up to avoid the hazard.
Programming Copy Cable
Software Cable (QXPL-01)
~ Alwarningl
ST-6.5-150V-1 ST-8.5-400V-1
Whenjewelry, keys or ornamental chain and other electric metals contact
~
ST-8.5-150V-2 ST-10-400V-2 with the battery terminal, the battery may cause damage or hurt bodies.
If the battery terminal short circuit it wi! generate a lot of heat, Please be
careful when you bring or use the battery, especially put it into the pocket,
purse or other metal container.
HOW TO CHARGE INSTALLIN THE ACCESSORIES
CD mtlDt::r:D
CD •••• em
•••• _a:t
CD _cu:>cm
J
the MIC-SP jack,then plug the earphonel
Installing the Belt Clip:
"Mic into the jack of earphone/MicWhen
Aim the screw eyes of belt clip and iO .
uSing earphone/Mic,it will affect the perf-
the AI. shell of transceiver at each
ormance of waterproof.
other,then fasten the belt clip with
~@
the screws.
Removing the Belt Clip:
When remove the belt c1ip,fastening
its fixed screws.
GETTING ACQUAINTED GETTING ACQUAINTED
2. LED Indicator
Lights RED while transmitting,lights KELLY while receiving,
flashes RED while in low battery.
3. Circumrotate Encoder
Rotate to select channels, and also work with other function
keys to set functions.
4. [PTT] Switch
Press,then speak into the microphone to transmit, and also
work with other function keys to set functions.
5. [MONI] Key
According to how to program auxiliary functions of this key.
Please refer to P30 of the details instruction,press ON/OFF
the programmable auxiliary function,and also work with other
function keys to set functions.
6. [DIAL] Key
Use to store/confirm/transmitldelete DTMF number,also using
as a function key.
7. [FUNC] Key
Function key,press to unlock other functions setting.
GETTING ACQUAINTED GETTING ACQUAINTED
8. [SCAN] Key 75
+
13 DCS C,
ACT " C,
" C•.O " i, ~gl!.I!!
" " O.C'· 100
Press to begin or stop scanning,and also work with other -l!!llil •••• vox~ R
..... _---
While receiving, it means signal strength
(the more,the stronger), while transmitting,
it means power(the more,the higher).
[i Displayswhen pressingFUNC to set the functions
II!] Displays when transmitting in low power.
Power ON/OFF
Turn [Power SwitchNolume Control] clockwise to power ON the
• Channel mode displays UNPG if any channel hasn't been
transceiver. programmed. You can only press DIAL to change to frequency
Turn [Power SwitchNolume Control] counterclockwise to power mode.
OFF the transceiver.
Choose Channel
Volume Control This function is valid under the display mode of Channel and
Rotate [Power SwitchNolume Control] to adjust volume.Turn
Frequency+ChanneI.Rotate[Circumrotate Encoder] to choose
clockwise to turn up the volume while turn counterclockwise
needed channel.Turn clockwise to increase the channel num-
to turn down. When adjusting the volume, press MaN I to mo- ber while turn counterclockwise to decrease it.
nitor the background noise.
• When communicating with others, you need to adjust the
volume correctly. • When the programmed frequency of chose channel is out of
the range of transceiver, it will alert you out of lock.
Choose Displaying Mode
There are 3 kinds of displaying modes for free choice. • The screen displays chose channels.
Channel Mode Choose Frequency
Press DIAL for 1 second (the prompting voice would be heard
This function is valid only under the display mode of Frequency.
if set)," Iii "flashes on the screen,then press Law.
There are 2 ways for free choice.
• The current channel displays on the screen.
1. Input frequency
Frequency+ChannelMode
Rotate [Circumrotate Encoder] to choose frequency,turn clo-
Press DIAL for 1 second,and then press again.
ckwise according "stepping" to increase frequency while turn
• The current communicating frequency and channel displays
counterclockwise to decrease it.
on the screen. • The selected frequency displays on the screen.
Frequency Mode
Press DIAL for 1 second, and then press SCAN.
• The current communicating frequency displays on the screen. • Please select the stepping before circumrotate encoder to
choose frequency (Refer to P22 of "STEPPING'?
BA!iIC OPERATION BA!iIC OPERATION
2. Input frequency on Keypad 2. Turn the encoder from O(open) to 9(tightest) to select the
squelch level.
• Press [DTMF],then input the frequency directly.
• Turn clockwise to increase the squelch level,turn counter-
E.g. linput 4,0,3,0,5,0 when communicating in 403,050MHz,
clockwise to decrease the squelch level.
he screen displays 403,050, that means you can communi-
3. Press any key to end the setting.
cate in 403,050MHz.
• Return to normal operation.
NOTE: Input frequency on keypad is related to stepping,use
Circumrotate Encoder to select and adjust frequency. Transmitting
According to different settings for the monitor function,press
• The input frequency displays on the screen.
MaN I to monitor the loudspeaker for a moment,and confirm
there is no broadcasting station is transmitting on the selected
• When inputting wrong frequency,press [MON/} to cancel. channel. Press PTT, and then speak into the microphone.
• Frequency range and stepping frequency of transceiver would 1. Please keep the microphone approximately 3-4cm from
restrict the frequency you inputPlease pay more attention your mouth,and speak in normal speaking voice to ensure
about the stepping you set. best performance.
2. When pressing PTT, LED lights RED.
Squelch
3. Release PTT to receive.
When there is no signal,squelch function can mute loudspeaker.
When squelch function is ON,you will hear the background noise Receiving
from the loudspeaker, while the squelch is OFF you will not hear If the working channel is called, LED lights Green,you can
the background noise. The squelch level you choose will decide receive the call.
when your squelch is ON/OFF. If the level is too high,you cannot • If the signal is weak and you have set the higher squelch
get weak signal, if the level is too low, the signal will appears in level,you may miss the call.
the background noise. • Local dealer may program the CTCSS/DCS.You could only
How to Adjust Squelch receive calling from the station that selected the same
1. Press FUNC for 1 second, then press Law. CTCSS/DCS as yours. Other callings cannot be heard.
Channel Scanning
This function is valid only under the display mode of Channel
and Frequency+Channel, which is used to monitor every added
scanning channel of the transceiver. When scanning, the trans-
ceiver will check every channel and only stop in the channel
with signal.
ADVANCED OPERATION ADVANCED OPERATION
1. Press SCAN to begin scanning. DTMF Calling
• Scan starts from current channel,and channel number Manually Dialing
increases gradually. Screen displays "SCAN". Press PTT, and then enter the needed numbers.
• The transceiver will stay in the communicating channel until • Press PIT,then enter the first digit you input,release PIT,
the signal disappears. Scan will return after signal disapp- and then release the digits keypad,the transceiver will keep
ears for 4 seconds, unless there is new signal appears
transmitting within 2 seconds,you need not keep pressing
within these 4 seconds.
PTTto dial.
2. Press any key except MONI to end scanning.
• When transmitting DTMF, microphone will be muted,you can
Frequency Scanning monitor the double-audio-frequency through loudspeaker.
This function is valid only under the display mode of Frequency.
Automatically Dialing
It is used to monitor the signal in every frequency of the step-
Dial Saved DTMF Numbers
ping.When scanning,transceiver will check the increased step-
Dial saved DTMF number of the memory number units.
ping and only stop in the frequency with signal.
1. Press DIAL to enter the dial-up mode.
1. Press SCAN to begin scanning.
• Scan starts from current frequency,and increases according • Screen displays "__ d"
• Screen displays "SCAN" • Screen displays and scrolls the calling numbers and
sounds DTMF.
3. Return to the former display automatically.
When the increased frequency range is out of transceiver frequency,
Redial DTMF Numbers
it will turn to the lowest frequency to increase as per "stepping".
Redial the last transmitted DTMF number (16 digits max.)
The transceiver will stay in the communicating frequency until 1. Press DIAL to enter the dial-up mode.
the signal disappears. Scan will return after signal disappears
• Screen displays "__ d"
for 4 seconds, unless there is new signal appears within these
2. Press [0] to dial the last transmitted number.
4 seconds.
• Screen displays and scrolls the calling numbers and
• When scan quit in a specific frequency, the screen displays
sounds DTMF.
frequency rate, the dot between frequency will flash on the
3. Return to the former display autimatically.
screen.
2. Press any key except MONI to end scanning.
ADVAI\ICED OPERATION ADVANCED OPERATION
Save DTMF Numbers 3. Input the needed delete DTMF numbers (1-9).
1. Press DIAL to enter the dial-up mode. • The selected DTMF numbers were deleted.
• Screen displays "__ d" 4. Return to the former display automatically.
2. Press [#] to enter the store mode. Key Locked
3. Enter the numbers in the DTMF keypad. This function is to avoid operating transceiver incorrectly,to lock
• If you input incorrect number, press -MaN I to clear it and keypad of the transceiver.
enter the correct one. 1. Press FUNC for 1 second, the function is ON.
4. Press DIAL after input the digits, and then enter digits of the
• "Iii " flashes on the screen.
memory channel numbers (0-9). 2. Press [*] to enter Key Locked.
• Return to the former display. • "+" displays on the screen.
Confirm Saved DTMF Numbers
• When key locked function is ON, all the keys are invalid
Check the memory channel number units.
except PTT,MONI,FUNC.
1. Press DIAL to dial-up mode. To unlock keypad of the transceiver, please repeat the above operation.
• Screen displays "__ d"
Lightening
2. Press [*] to enter confirmed saved mode.
You can set the lightening function to be automatism, connec-
3. Enter the needed memory number units (1-9)
tion or off.
• Screen displays and scrolls the saved DTMF numbers
1. Press FUNC for 1 second, the function is ON.
and sounds correspongding DTMF.
• "Iii" flashes on the screen.
4. Return to the former display automatically.
2. Press [2] to select lightening function.
Delete Saved DTMF Numbers 3. Rotate [Circumrotate Encoder] to select the needed setting.
Delete the memory channel number units. • Displays "A" for automatism. The light on screen will light
1. Press DIAL to enter the dial-up mode . for 5 seconds when press any key except PTT and MONI,
• Screen displays "__ d" and then put out automatically.
2. Press [0] to enter the delete mode . • Displays "ON" for connection. The light on screen will light
• Screen displays "c1r_d" when the transceiver is power ON.
Press any key except digit keys from 1 to 9 to cancel the
• Displays "OFF" for cutting off. The light on screen will not work.
operation. 4. Press any key to end setting,and return to the former display.
ADVANCED ,OPERATION ADVAI\ICED OPERATION
Reverse Frequency VOX
Transmitting and receiving frequency will reverse when using This transmitting function can communicate hands-freely. When
the reverse frequency function. It means to transmit with receiv- using VOX, if microphone's gain is higher than VOX gain,
ing frequency, to receive with transmitting frequency. If set CTCS the transceiver will turn to transmitting mode automatically while
SIDCS function,encoding and decoding signal will also reverse. return to receiving mode after 2 secends if microphone's gain is
1. Press FUNC for 1 second, the function is ON. lower than VOX gain. Owing to switching between transmitting
• "F" flashes on the screen. and receiving, we suggest not transmit when setting VOX gain if
2. Press [3] to set reverse frequency function ON. the surrounding is too noisy.
1. Press FUNC for 1 second, the function is ON.
• Screen displays "R"
While changing channel/frequency or scanning, the reverse • "F" flashes on the screen.
2. Press [1] to enter VOX function.
frequency function is OFF.
• "VOX" flashes on the screen,at the same time the top right
3. Repeat the above operation,the channel will alternate
corner of the screen displays the current VOX transmitting
between ON/OFF reverse frequency.
gain.
Stepping 3. Rotate [Circumrotate Encoder] to select the VOX transmitting
This function is valid only under the mode of full range of Fre- gain from "OF" to "3".
quency. Setting setpping would restrict the transceiver choos- • Turn clockwise to increase VOX transmitting gain while turn
ing frequency and frequency scanning. counterclockwise to decrease it.
1. Press FUNC for 1 second, the function is ON. • Screen displays "OF" when VOX is OFF. "1" means low gain,
• "[ii " flashes on the screen. "2" means middle gain, "3" means high gain.
2. Press [#] to select stepping frequency. 4. Press any key to end setting.
• Screen displays the current stepping frequency. • Screen displays "VOX" when select the gain from 1 to 3 and
3. Press LOW to choose stepping frequency in circle. displays nothing when VOX function is OFF.
5 means stepping is 5KHz
6.25 means stepping is 6025KHz CTCSS/DCS
12.50 means stepping is 12.50KHz
When the channel setting CTCSS/DCS code,the squelch func-
25 means stepping is 25KHz
50 means stepping is 50KHz tion ON only received the corresponding CTCSS/DCS code.
1.000 means stepping is 1.000KHz And, the transceiver which has the same CTCSS/DCS code
10.000 means stepping is 10.000KHz
can receive the signal you transmit.
4. Press other key to end setting,and return to the former display.
ADVAI\ICED OPERATIOI\I ADVAI\ICED OPERATIOI\I
3. Press LOW to select the mode of CTCSS/DCS/OFF in circle.
• Program CTCSS/DCS code in your transceiver can help
you to ignore (not hear)some unnecessary callings from • Displays "q" before the digits when select CTCSS code,
displays "d" before the digits when select DCS code, select
ther transceiver. But that not means your calling is privacy.
"OFF" to delete.
Adjust Receiving CTCSS/DCS Decode
• When select DCS code, press DIAL to choose Normal or
1. Press FUNC for 1 second,the function is ON.
Inverted code. Inverted code displays" - " while Normal
• "F" flashes on the screen.
code displays nothing.
2. Press [A) to adjust receiving CTCSS/DCS decode.
4. Rotate [Circumrotate Encoder) to select new CTCSS/DCS code.
• Screen displays the current code.
5. Press any key except PTT and MONI to exit and store the
3. Press LOW to select the mode of CTCSS/DCS/OFF in circle.
adjusted code.
• Displays "q" before the digits when select CTCSS code,
• Set CTCSS decode,screen displays "CT" while transmitting.
displays "d" before the digits when select DCS code, select
Set DCS decode,screen displays "DCS" while transmitting.
"OFF" to delete.
Set OFF,screen displays nothing.
• When select DCS code, press DIAL to choose Normal or
Inverted code. Inverted code displays" - " while Normal Slip Frequency
code displays nothing. This function is valid only under the display mode of Frequency,
4. Rotate [Circumrotate Encoder] to select new CTCSS/DCS setting the slip frequency of receiving and transmitting it.
code. 1. Press FUNC for 1 second, the function is ON.
5. Press any key except PTT and MONI to exit and store the • "~" flashes on the screen.
adjusted code. 2. Press [0) to set slip frequency.
• Set CTCSS decode,screen displays "CT" while receiving. • Screen displays the current slip frequency status.
Set DCS decode, screen displays "DCS" while receiving. 3. Press SCAN to select +/- slip frequency.
Set OFF,screen displays nothing. • " 13 " displays before the frequency when it is - slip frequ-
Adjust Transmitting CTCSS/DCS Encode ency, while + slip frequency displays nothing.
1. Press FUNC for 1 second, the function is ON. 4. Rotate [Circum rotate Encoder) to increase/decrease slip
This function is valid only under the display mode of Channel Delete Channel
and Frequency+Channel. Copy one channel data of the Delete the programmed channel data of the transceiver.
tranceiver to other channel. 1. Press FUNC for 1 second, the function is ON.
1. Select the needed copy channel. • "1:iI " flashes on the screen.
2. Press FUNC for 1 second to set the function ON. 2. Press [0] to select the deleted channel.
• " I:iI "flashes on the screen. • Screen displays the deleted channel.
3. Press [C] to select the saved copy channel. 3. Rotate [Circumrotate Encoder] to select the needed delete
• Screen displays the saved channel. channel.
4. Rotate [Circumrotate Encoder] to select the channel. • Press any key except PTT to exit but not store.
• Press any key except [PTT] to exit but not store. 4. Press PTT to store and exit.
5. Press PTT to store and exit. • This channel data was deleted and never displays besides
• Now the initial channel data is the same with saved channel data you reprogrammed it.
ADVANCED OPERATION AUXILIARY OPERATION
Copy Function with Cable Adopt OXPG-78D(Software) and OXPG-01
Copy function with cable is that copying the data from a trans- (Program cable) to program.
ceiver to another transceiver without any exterior equipment.
Time-Out Timer
The purpose of the Time-out timer is to prevent any single
person from using a channel for an extended period of time. If
• This function is ON only when the local distributor set
it for you. you continuously transmit more than limited time, the transceiver
will stop transmitting and an alert tone will sound. To stop the
1.Power off the main transceiver. Press [LOW] and [MONI] at
tone, release PIT.
the same time to power on and enter into the copying status.
• Pre-caution before TOT: The alert tone sounds before the
The screen displays "COPY".
limited TOT time of the transceiver.
2.Repeat STEP 1 for the target transceiver. The screen displays
• Interval after TOT: It is interval after limited TOT time you
"COpy" too.
have set. You cannot transmit during this interval.
3.Connect the two transceivers with specified copying cable.
• TOT resume time: Pre-set TOT resume time,when this
4.Press [FUNC] of the main transceiver to begin to copy. The
function is on,you can not transmit before TOT resume time.
screen displays "COPY-t", sending its data to the target
Only when resume time arrives,then can transmit again.
transceiver.
S.The two transceivers display "COpy" when finishing the [MONI] Key Setting
copying and back to copying stand-by status. If it is needed MONI key can be set as the following auxiliary functions.
to copy to another target transceiver, the target transceiver • Squelch OFF(Default setting)
should enter into copying status first, and then repeat STEP Press to hear the background noise,release to return the
3 and STEP 4. Repeat the operations for multi-transceivers. normal operation. It is used to get the weak signal which you
6.Restart the power again when finishing copying, and the can't get even operated correctly.
machine will back to normal working status. • None( No function)
No operation if press.
• When in stand-by status, displays COPY.
• When in receiving status, displays COPY-r. • Activate Monitor
• When in transmitting status, displays COPY-I. Press to set CTCSS/DCS OFF, press again to return normal
. operation.
AUXILIARY OPERATION AUXILIARY OPERATION
• Monitor Momentary tone sounds,stop transmitting and the indicator flashes.Please
Press to set CTCSS/OCS OFF, release to return normal change or charge the battery.
operation.
Busy Channel Locked PTT 10 is used to continue or stop some repeaters and telephone
When this function is ON, it can avoid interfering other stations system. Press PIT to transmit 10 signal if set begin transmitting.
of the same channel using with yours.When press PIT, if the Release PIT to transmit 10 signal if set stop transmitting.Press
channel is being used,your transceiver will alert, and return to PIT then release it to transmit 10 signal if set begin and stop
the receiving status. transmitting signal.
Prompting Voice
You can choose prompting voice ON/OFF. This covers all
prompting voice of the transceiver.
136-174MHz Receiving -
Frequency Range 350-390MHz Wide band <0.18JN (12dB SINAD)
Sensitivity
400-470MHz etc. Narrow band<0.25jlV