Model TE – 135 Infusion Set Designated TERUMO IV sets for pump Pumping System Peristaltic Finger Method Control Method Volumetric Control Delivery Rates STANDARD mode: 1 – 999 mL/h ( 1 mL/h step ) MICRO mode: 0,1 – 99.9 mL/h ( 0.1 mL/h step ) Delivery Limit 1 – 9999 mL ( 1 mL step ) or “ - - - - “ ( Delivery Limit Free ) Volume Delivered STANDARD mode : 0 to 9999 mL ( 1 mL step ) MICRO mode : 0.0 to 99.9 mL ( 0.1 mL step ) 100 to 9999 mL ( 1 mL step ) Flow Accuracy ± 10 % Conditions Infusion Set: Designated TERUMO IV sets for pump. • Solutions : Water / Saline • Test Time : Second Hour • Delivery Rate : 1.0 mL/ h or more • Temperature : 25 o Celcius With a designated Infusion Set water or saline, measured at 1 hours after start-up and subsequent every hour. ( Actual Flow Accuracy depends on the type of solution ) Occlusion Pressure 30 – 140 kPa ( 0.30 – 1.43 kgf/cm2 ) Purge Approx 500 mL/h Alarms Battery, Air-in-line, Occlussion, Door, Infusion Completion ( Keep Open Rate Function ), Repeat ( activated if the cause of the initial alarm remains for about 2 minutes ), Start Reminder ( activated if about 2 minutes wasted after infusion become available ), Battery Error, Delivery Rate/Delivery Limit Comparison alarms. Alarm when using Drip Sensor ( Option ): Empty, Flow Error ( Free Flow ) ( An alarm during infusion is recognized by the relevant alarm indicator or display, the operation indicator, a buzzer etc. The pump is stopped by any alarm other than the Battery ( except Shutdown ) and Infusion Completion Alarms Safety Functions • Panel Lock : Disables the user to change the D Rate, D Limit values when the door is opened * • Tube Clamp : Automatically presses and shuts the IV tubing when the door is opened • Key Lock : Disables the switches except ( START ), ( KEY LOCK ), & ( POWER ). This function is deactivated when any alarm is occurred * • Air in-line Detection Sensitivity : adjust the sensitivity of the air-in-line detector in 2 steps (Low/High;default: Low ) • Occlusion Detection Sensitivity: Adjust in 10 steps ( default: 5 ) • Maintenance Timer : Turns on the maintenance timer indicator after a specified time passes ( Default: not used ) • Upper Limit of D Rate : Limit the maximum D Rate value withinthe predefined range Additional Function • Volume Delivered Clear : Reset the volume delivered to “ 0 “ when pressing VOLUME DELIVERED switch for 2 second • Alarm Volume : Adjust the alarm volume in four steps ( Small / Medium / Large / Step ( escalating ), default : Medium • Shutdown : Turns the pump off after alarming if the internal battery voltage lower to a certain level during operation on the battery • History : Activates the History mode to display the past operation record • Stand-by : Deactivates the Start Reminder alarm for 20 minutes with a long press of the ( STOP/SILENCE ) switch • Cable Disconnection Detection : Detect the power cable disconnection from the pump and gives an alarm * • Buzzer Sound Option : Switches the alarm buzzer to a continuous sound • Infusion Mode Limit : Disables the user to change MICRO mode Operating Conditions Temperature : 5 – 400 Celcius Humidity : 20 – 90 % Storage Conditions Temperature : - 20 – 450 Celcius Humidity : 10 – 95 % Power Supply AC : 100 – 240 Volt, 50/60 Hz DC : 12 – 15 Volt/DC Power Consumption 28 VA ( Watt )/ AC 100 – 240 Volt 11 Watt ( DC Power ) Classification Class I and Internal Power Supply Type CF, IPX1, Continuous operation Dimensions 100 mm (W) x 201 mm ( H) x 187 mm ( D ) Weight Approx 1.7 kg Accessories AC Power Cable, Pole Clamp, Time Lag Fuse ( 2 pcs ), Instruction Manual For Model TE-135C only: Nurse Call Output Connectable with nurse call via the computer interface/nurse call connector. Contact capacity: DC 12 Volt, 1 Ampere Computer Interface Data output available via RS232 or RS485 connector Accessories Computer Interface Protocol Optional Accessories • DC Cable ( Sold Separately ) • Drip Sensor ( Code No: TE*975 )