Professional Documents
Culture Documents
AS 1101-2 Ventilation Symbols in Ships PDF
AS 1101-2 Ventilation Symbols in Ships PDF
AS 1101-2 Ventilation Symbols in Ships PDF
2—1972
Australian StandardR
This standard, prepared by Committee MS/22, Shipbuilding, were approved on behalf of the
Council of the Standards Association of Australia on 24 August 1972.
Review of Australian Standards. To keep abreast of progress in industry, Australian Standards are subject to
periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important
therefore that Standards users ensure that they are in possession of the latest edition, and any amendments thereto.
Full details of all Australian Standards and related publications will be found in the Standards Australia Catalogue
of Publications; this information is supplemented each month by the magazine ‘The Australian Standard’, which
subscribing members receive, and which gives details of new publications, new editions and amendments, and of
withdrawn Standards.
Suggestions for improvements to Australian Standards, addressed to the head office of Standards Australia, are
welcomed. Notification of any inaccuracy or ambiguity found in an Australian Standard should be made without
delay in order that the matter may be investigated and appropriate action taken.
This Standard was issued in draft form for public review as Doc. 1809.
AS 1101.2—1972
Australian StandardR
CONTENTS
Page Page
SPECIFICATION TABLES
1 Scope . . . . . . . . . . . . . . . . . . . . 3 1 General conventional symbols . . . . . 4
2 Definitions . . . . . . . . . . . . . . . . 3 2 Ducts and duct joints . . . . . . . . . . . . . 4
3 Symbol Rules . . . . . . . . . . . . . 3 3 Damper and duct fittings . . . . . . . . . . 6
4 Symbols . . . . . . . . . . . . . . . . . . 3 4 Ventilators, cowls and pipes . . . . . . . 8
5 Appliances . . . . . . . . . . . . . . . . . . . . 10
3 AS 1101.2—1972
Australian Standard
for
GRAPHICAL SYMBOLS FOR GENERAL ENGINEERING
SPECIFICATION
1 SCOPE. This standard sets out symbols for use in With certain obvious exceptions symbols may be
schematic drawings of ventilation systems in ships. rotated or reversed without altering their meaning.
The standard shows basic symbols, describes the The symbols may be drawn to any suitable size.
principles on which they are based, and illustrates The size may be varied on any given drawing for
some representative composite symbols. emphasis or clarity.
2 DEFINITION. A ‘symbol’ consists of the lines, Arrows as shown in Table 1, item 1.1.1 shall be
letters and abbreviations which identify the purpose used to indicate adequately the direction of flow in all
and method of operation of the component illustrated. systems.
3 SYM BOL RULE S . T he symbols show 4 SYMBOLS. Symbols shall conform to those set
connections, flowpaths and the function of the out in Tables 1-5. Each drawing should contain a
component represented. symbol list, preferably only showing those symbols
actually used in the drawing. The list should make
The symbols need not necessarily show the reference to this standard.
physical location of parts or the position of control
elements on actual components.
AS 1101.2—1972 4
TABLE 1
GENERAL CONVENTIONAL SYMBOLS
TABLE 2
DUCTS AND DUCT JOINTS
5 AS 1101.2—1972
TABLE 2
(continued)
AS 1101.2—1972 6
TABLE 3
DAMPER AND DUCT FITTINGS
+ These symbols may be associated with symbols 2.6 and 2.7 for verti cal install ations.
* The rectangular outli ne in plan view may be shown circular.
7 AS 1101.2—1972
TABLE 3
(continued)
* Moisture eli minati on system symbol, item 5.9, should be used in conjuncti on wit h these items where applicable.
NOTE: For special cabin units or proprietary lines, the type of unit must be specifi ed.
AS 1101.2—1972 8
TABLE 4
VENTILATORS, COWLS AND PIPES
9 AS 1101.2—1972
TABLE 4
(continued)
AS 1101.2—1972 10
TABLE 5
APPLIANCES