Professional Documents
Culture Documents
Komatsu Handbook
Komatsu Handbook
SPECIFICATIONS &
APPLICATION HANDBOOK
Edition 25
March 2004
CONTENTS
INDEX
Please note that the performance information included in this book is for
estimation purposes only. It is based on information that Komatsu Ltd. has
but actual figures will vary with the operating conditions, including
material characteristics, site conditions, operator efficiency, etc. Neither
Komatsu Ltd. nor its dealers will guarantee that the machines will perform
as estimated.
c 2004 Komatsu
All Rights Reserved
Printed in Japan
G-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
G-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
CONTENTS
INDEX
GENERAL INFORMATION BY INDEX TABLE
PREFACE
KOMATSU PRODUCT LINE
11 ENGINES 11 ENGINES
12 TIRES 12 TIRES
INDEX INDEX
G-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
G-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
G-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Preface GENERAL
PREFACE
This handbook referes to machine specifications, productivity and owning & operation cost for construction
equipment sold by Komatsu. It serves as a guide for the following cases:
* Estimation of productivity for each machine
* Estimation of owning & operating costs for each machine
* Selection of machines for purchasing construction equipment
* Selection of machines for performing construction job
The performance of a machine is determined by its production and operating costs. Important machine
factors that influence production includes the horsepower, operating weight, capacity of work equipment,
traveling speed and types of mechanical, hydraulic and electrical systems. They are referred to in the related
section in the handbook. Some of the significant elements that comprise the operating cost factors are the
consumption of fuel and lubricants, the service life of tires and undercarriage and the repair cost of
components. These expenditures are discussed in the section entitled Owning & Operating Costs.
The data and tables in the handbook are based on Komatsu's bench and field tests, computer analysis and
many years of experience. We continuously conduct tests to improve the reliability of the data. However,
because of the complexity of factors influencing production costs and the deviations that may occur during
the preparation of data, Komatsu does not guarantee that the data is exact and that the performance shown
in the handbook is always obtainable with the given job conditions.
The basic performance data in the handbook are the values when machines are used at ideal efficiency. As
performance varies with operator's skill, ground and weather conditions, etc., in reality, the basic data needs
to be modified by using the various factors included in the handbook, resulting in different figures depending
on the selection of these factors. Owning and operating cost also varies depending upon the machine usage,
and the calculation result differs by what job condition and factors are applied for the calculation. Therefore, it
should be understood that the calculated figures do not always completely match the actual measured data.
Nevertheless, handbook users will be able to make proper approximate calculations based on the data given
in the handbook, their work experience and knowledge of local conditions.
This handbook is revised yearly. The data in the handbook is accurate at the time of printing; however,
Komatsu may make changes in the specifications and materials without notice. Changes are made because
of Komatsu's fundamental program of conducting continuous improvements on its products. Therefore, when
you need the most updated information or specifications, obtain the latest catalogs through your distributor.
This handbook contains machine models produced in the various areas in the world. Specifications may vary
depending upon production location; all models are not always available everywhere in the world.
The final objective for an owner of construction equipment is to perform the necessary construction job with
the best efficiency and safety. It is desirable for an owner to understand the job efficiency factors and the
machine use factors before utilizing this handbook.
They are as follows:
G-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Preface GENERAL
G-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Preface GENERAL
3) Prevention of fire
The owner and operator of a construction machine must follow the machine's maintenance guidelines
and manage the job so that danger of fire will be minimized. A fire breaks out mainly by leakage of fuel,
oil and grease; by electrical shorts caused from fatigue, loosening, or rubbing of electric parts and by
ignition from engine high temperature parts contacting combustibles, such as plants and papers.
• The owner of a machine needs to maintain a machine by daily checks so that the causes described
above do not exist.
• The operator must confirm by walk-around check before starting the machine that the above-
mentioned hazards do not exist. If any problems are found, the machine must not be started until the
problems are fixed.
• Equip a machine with a fire extinguisher in preparation for emergency.
G-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
BULLDOZERS
Flywheel horsepower 40 to 1150 HP (29.5 to 858 kW)
SWAMP BULLDOZERS
Flywheel horsepower 40 to 225 HP (29.5 to 168 kW)
PIPELAYERS
Flywheel horsepower 225 to 360 HP (168 to 259 kW)
G-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
G-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
WHEEL LOADERS
Bucket capacity 0.3 to 20 m3 (0.4 to 26.2 yd3)
(C) indicates custom series.
WA500-3 WA480-5 WA450-5 WA400-5 WA420-3 WA380-3 WA320-3 (C) WA250-5 WA250PT-5
WA470-5 WA430-5 WA380-5 WA320-5 WA270-5
WA470-3
WA200-5 WA200PT-5 WA150-5 WA115-3 WA95-3 WA80-3 WA85-3 WA65-3 WA50-3 WA30-5
WA90-3 WA75-3
WT500E WT250E SK1026-5 SK1020-5 SK820-5 SK818-5 SK815-5 SK714-5 SK510-5 SK04J-2
BACKHOE LOADERS
Bucket capacity 0.7 to 1.03 m3 (0.92 to 1.35 yd3)
G-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
CRAWLER CARRIERS
Hauling capacity 6 to 11 ton (6.6 to 12.1 US ton)
CD110R-2 CD60R-1
MOTOR GRADERS
Flywheel horsepower 125 to 280 HP (93 to 209 kW)
ROAD STABILIZERS
Flywheel horsepower 203 to 355 HP (152 to 265 kW)
GC380F-2 CS210-2
VIBRATORY ROLLERS
Operating weight 600 to 11,250 kg (1,320 to 24,800 lb)
TIRE ROLLER
Operating weight 3,000 kg (6,610 lb)
JW30-2
G-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
LT500-1 LT300-2
MOBILE CRUSHER & RECYCLERS
Flywheel horsepower 54.2 to 612 HP (40 to 456 kW)
PC78UUT-6 PC58UUT-3
G-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
ENGINES
Piston displacement 3.92 to 61.8 Itr (239 to 3771 cu in)
G-14
CONTENTS
SECTION 1
INDEX
SECTION 1A
CRAWLER-TYPE
TRACTORS
CONTENTS
Features .................................................................... 1A-2
Specifications ........................................................... 1A-7
Specifications (Low ground pressure) ................. 1A-11
Drawbar pull vs. travel speed ............................... 1A-13
Ground pressure .................................................... 1A-16
Shoe application .................................................... 1A-18
Shoe selection ........................................................ 1A-19
Roller guard installation ........................................ 1A-21
Upper attachment ................................................... 1A-23
1A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features CRAWLER-TYPE
TRACTORS
High productivity
The high-power engine, highly efficient power train,
large drawbar pull provided by the conventional
undercarriage, and the high performance work
equipment provide high productivity.
• Large capacity blade
Large capacity blade, powerful digging force,
large up-and-down movement of the blade, and
high strength provided by high tensile steel.
• Uniquely designed ripper FVBH0305
1A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Features CRAWLER-TYPE
TRACTORS
• Reduction of man-hours for turning over the NEW
CURRENT
bushings by employment of wedge ring. (Large
Class)
Track roller
• Strengthening of undercarriage by increase of
press fitting width of pin. (Small-middle Class) Track link
The most important matters for the undercarriage
of a bulldozer are holding of the oil filled in the
links and easiness of turning over the bushings. Roller guard
KOMATSU increased the rigidity and abrasion life
of the links and lowered the press fitting force of Wedge ring
Link pin
Bushing
WIDE
NARROW
PRESS FITTING WIDTH
Others
Use
Track 3 Others
Turning over
the bushings
New bushings Before turning over
er
ov
the bushings
g
Track 2 Track 2
in
rn
Tu
After turning over Used bushings With turning over Without turning over
the bushings the bushings the bushings
Final drive
FVDM0692
1A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Features CRAWLER-TYPE
TRACTORS
1A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Features CRAWLER-TYPE
TRACTORS
• Centralized oil pressure inspection ports D375A-5
Oil pressure check ports are centralized on the
left side of the chassis to make it easier to carry Single tilt
out inspection and maintenance. Dual tilt
Easy maintenance
• Bolt-on type sprocket or segmented sprocket
teeth for easy in- field replacement. [Except D21]
FLD00421
• Simple maintenance is promoted through
adoption of spin-on type fuel and full-flow filters,
an air cleaner with an automatic dust evacuator,
and others.
• Maintenance-free, wet, multiple-disc
brakes
To ensure long life and dependability
maintenance-free, wet, multiple-disc brakes are
utilized.
(D41, D61, D65, D155A-5/D155AX, D275A,
D375A, D475A and D575A)
1A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Features CRAWLER-TYPE
TRACTORS
• HST dynamic brakes
Fulcrum of major bogie
KomStat uses HST dynamic brakes to ensure
safe operation.
Parking brake is wet, multiple-disc type with a
unique drag-prevention control to keep hydraulic
oil clean.
(D31, D37 and D39)
• K-Bogie undercarriage system
New K-Bogie undercarriage system retains prior
advantages, with new additional features.
New features on K-Bogie Undercarriage Fulcrum of minor bogie
System:
• K-bogies oscillate with two fulcrums, and track
roller vertical travel is greatly increased.
Impact loading on all undercarriage
components has been reduced and durability
of components is improved since track rollers
are always in contact with tack link.
• Undercarriage life is improved due to better
control of track chain alignment with track
rollers.
• Riding comfort is improved by reducing
vibration and shock when traveling over rough
terrain.
(D275A, D275AX, D375A and D475A)
• Auto-shift down function
Controller monitors engine speed, travel gear and
travel speed.
When load is applied and machine travel speed is
reduced, the controller automatically downshifts
to optimize gear speed to provide high fuel
efficiency. This function provides comfortable
operation and high productivity without manual
downshifting. (This function can be deactivated
with cancel switch).
(D275, D375A and D575A SD)
• Preset travel speed selection function
Preset travel speed selection function is standard
equipment, enabling the operator to select fore
and aft travel speed among three preset patterns,
F1-R2, F2-R2 and manual shift. When F1-R2 or
F2-R2 preset pattern is selected, and travel
control joystick moves from forward to reverse
direction, the machine travels forward/reverse
with F1/R2 or F2/R2 speed automatically. This
function reduces gear shifting time during
repeated round trip operations.
(D275, D375A and D575A SD)
1A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Specifications CRAWLER-TYPE
TRACTORS
Model
D21A-8 D31EX-21 D31EX-21*** D37EX-21
Item
OPERATING WEIGHT* kg (lb) 3710 (8,180) 7130 (15,720) 7130 (15,720) 7410 (16,340)
TRACTOR WEIGHT kg (lb) 3160 (6,970) 5775 (12,730) 5775 (12,730) 6010 (13,250)
FLYWHEEL HORSEPOWER HP (kW)/RPM 40 (29.5)/2450 75 (56)/2000 75 (56)/2000 85 (63)/2000
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 2.6 (1.6) 3.4 (2.1) 0.8 (0.5) to 3.4 (2.1)
2nd 4.4 (2.7) 5.6 (3.5) 8.5 (5.3) 5.6 (3.5)
3rd — 8.5 (5.3) — 8.5 (5.3)
Reverse 1st 3.3 (2.1) 4.1 (2.5) 0.8 (0.5) to 4.1 (2.5)
2nd 5.6 (3.5) 6.5 (4.0) 8.5 (5.3) 6.5 (4.0)
3rd — 8.5 (5.3) — 8.5 (5.3)
Max. drawbar pull kg (lb/kN) 4520 12500 12500 12500
(9,970/44.3) (27,560/123) (27,560/123) (27,560/123)
DIMENSIONS:
Overall length (tractor) mm (ft.in) 2405 (7'11") 3055 (10'0") 3055 (10'0") 3055 (10'0")
Overall length* mm (ft.in) 3250 (10'8") 4015 (13'2") 4015 (13'2") 4015 (13'2")
Overall width (w/o trunnion) mm (ft.in) 1610 (5'3") 1850 (6'1") 1850 (6'1") 1850 (6'1")
Overall width (with blade)* mm (ft.in) 2170 (7'1") 2435 (8'0") 2435 (8'0") 2720 (8'11")
Overall height (tractor)** mm (ft.in) 1785 (5'10") 1890 (6'2") 1890 (6'2") 1890 (6'2")
Overall height* mm (ft.in) 2450 (8') 2700 (8'10") 2700 (8'10") 2700 (8'10")
Track gauge mm (ft.in) 1310 (4'4") 1450 (4'9") 1450 (4'9") 1450 (4'9")
Length of track on ground mm (ft.in) 1685 (5'6") 2010 (6'7") 2010 (6'7") 2240 (7'4")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model 4D94LE SAA4D102E SAA4D102E SAA4D102E
No.of cylinders- mm (in) 4-94 × 110 4-102 × 120 4-102 × 120 4-102 × 120
bore × stroke (3.70 × 4.33) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 3.053 (186) 3.92 (239) 3.92 (239) 3.92 (239)
UNDERCARRIAGE:
No.of rollers (carrier/track) 1/5 1/5 1/5 1/6
Width of standard shoe mm (in) 300 (11.8) 400 (15.7) 400 (15.7) 400 (15.7)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 60 (15.9) 165 (43.6) 165 (43.6) 165 (43.6)
*) Spec conditions:
Bulldozer PAT PAT PAT PAT
Rear attachment — — — —
Upper attachment — ROPS canopy ROPS canopy ROPS canopy
Model
D37EX-21*** D39EX-21 D39EX-21*** D41E-6
Item
OPERATING WEIGHT* kg (lb) 7410 (16,340) 8520 (18,780) 8520 (18,780) 10950 (24,140)
TRACTOR WEIGHT kg (lb) 6010 (13,250) 6950 (15,320) 6950 (15,320) 8790 (19,380)
FLYWHEEL HORSEPOWER HP (kW)/RPM 85 (63)/2000 95 (71)/2200 95 (71)/2200 110 (82)/2300
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 0.8 (0.5) to 3.4 (2.1) 0.8 (0.5) to 2.4 (1.5)
2nd 8.5 (5.3) 5.6 (3.5) 8.5 (5.3) 4.4 (2.7)
3rd — 8.5 (5.3) — 7.6 (4.7)
Reverse 1st 0.8 (0.5) to 4.1 (2.5) 0.8 (0.5) to 3.0 (1.9)
2nd 8.5 (5.3) 6.5 (4.1) 8.5 (5.3) 5.5 (3.4)
3rd — 8.5 (5.3) — 9.4 (5.8)
Max. drawbar pull kg (lb/kN) 12500 13800 13800 14740
(27,560/123) (30,420/135) (30,420/135) (32,500/144.6)
DIMENSIONS:
Overall length (tractor) mm (ft.in) 3055 (10'0") 3195(10'6") 3195(10'6") 3610 (11'11")
Overall length* mm (ft.in) 4015 (13'2") 4200 (13'9") 4200 (13'9") 4880 (16'0")
Overall width (w/o trunnion) mm (ft.in) 1850 (6'1") 2110 (6'11") 2110 (6'11") 2300 (7'7")
Overall width (with blade)* mm (ft.in) 2720 (8'11") 2740 (9'0") 2740 (9'0") 3045 (10'0")
Overall height (tractor)** mm (ft.in) 1890 (6'2") 1965 (6'5") 1965 (6'5") 2020 (6'8")
Overall height* mm (ft.in) 2700 (8'10") 2770 (9'1") 2770 (9'1") 2900 (9'6")
Track gauge mm (ft.in) 1450 (4'9") 1650 (5'5") 1650 (5'5") 1790 (5'10")
Length of track on ground mm (ft.in) 2240 (7'4") 2360 (7'9") 2360 (7'9") 2485 (8'2")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA4D102E SAA4D102E SAA4D102E SA6D102E
No.of cylinders- mm (in) 4-102 × 120 4-102 × 120 4-102 × 120 6-102 × 120
bore × stroke (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 3.92 (239) 3.92 (239) 3.92 (239) 5.88 (359)
UNDERCARRIAGE:
No.of rollers (carrier/track) 1/6 1/6 1/6 1/6
Width of standard shoe mm (in) 400 (15.7) 460 (18.1) 460 (18.1) 510 (20.1)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 165 (43.6) 165 (43.6) 165 (43.6) 250 (66.0)
*) Spec conditions:
Bulldozer PAT PAT PAT PAT PAT
Rear attachment — — — — —
Upper attachment ROPS canopy ROPS canopy ROPS canopy ROPS canopy ROPS canopy
** : Without canopy, exhaust pipe, pre-cleaner cap or other easily removed encumbrances.
*** : With variable travel speed mode
*4 : Long track spec.
1A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Specifications CRAWLER-TYPE
TRACTORS
Model
D61EX-12 D61EX-12*4 D65E-12 D65EX-15
Item
OPERATING WEIGHT* kg (lb) 15800 (34,830) 16500 (36,380) 19125 (42,160) 20080 (44,270)
TRACTOR WEIGHT kg (lb) 13130 (28,950) 13830 (30,490) 15620 (34,440) 16350 (36,050)
FLYWHEEL HORSEPOWER HP (kW)/RPM 150 (112)/1800 150 (112)/1800 180 (135)/1950 190 (142)/1950
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 3.5 (2.2) 3.5 (2.2) 3.9 (2.4) 3.9 (2.4)
2nd 6.0 (3.7) 6.0 (3.7) 6.8 (4.2) 6.8 (4.2)
3rd 10.3 (6.4) 10.3 (6.4) 10.6 (6.6) 10.6 (6.6)
Reverse 1st 4.6 (1.9) 4.6 (1.9) 5.0 (3.1) 5.0 (3.1)
2nd 7.9 (4.9) 7.9 (4.9) 8.6 (5.3) 8.6 (5.3)
3rd 12.8 (8.0) 12.8 (8.0) 13.4 (8.3) 13.4 (8.3)
Max. drawbar pull kg (lb/kN) — — — —
— —
DIMENSIONS:
Overall length (tractor) mm (ft.in) 3935 (12'11") 4160 (13'8") 4365 (14'4") 4365 (14'4")
Overall length* mm (ft.in) 5030 (16'6") 5440 (17'10") 5440 (17'10") 5440 (17'10")
Overall width (w/o trunnion) mm (ft.in) 2500 (8'2") 2500 (8'2") 2390 (7'10") 2390 (7'10")
Overall width (with blade)* mm (ft.in) 3275 (10'9") 3275 (10'9") 3460 (11'4") 3460 (11'4")
Overall height (tractor)** mm (ft.in) 2195 (7'2") 2195 (7'2") 2330 (7'8") 2330 (7'8")
Overall height* mm (ft.in) 3115 (10'3") 3115 (10'3") 3165 (10'5") 3220 (10'7")
Track gauge mm (ft.in) 1900 (6'3") 1900 (6'3") 1880 (6'2") 1880 (6'2")
Length of track on ground mm (ft.in) 2600 (8'6") 3170 (10'5") 2675 (8'9") 2675 (8'9")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SA6D114E SA6D114E 6D125E SA6D125E
No.of cylinders- mm (in) 6-114 × 135 6-114 × 135 6 -125 × 150 6 -125 × 150
bore × stroke (4.49 × 5.31) (4.49 × 5.31) (4.92 × 5.91) (4.92 × 5.91)
Piston displacement ltr. (cu.in) 8.27 (505) 8.27 (505) 11.04 (674) 11.04 (674)
UNDERCARRIAGE:
No.of rollers (carrier/track) 2/6 2/8 2/7 2/7
Width of standard shoe mm (in) 600 (23.6) 600 (23.6) 510 (20.1) 510 (20.1)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 337 (89.0) 337 (89.0) 406 (107) 415 (109.6)
*) Spec conditions:
Bulldozer PAT PAT Semi-U tilt Semi-U tilt
Rear attachment — — — —
Upper attachment ROPS canopy ROPS canopy ROPS canopy Steel cab, ROPS
Model
D65EX-15*4 D68ESS-12 D70LE-8*** D85ESS-2
Item
OPERATING WEIGHT* kg (lb) 20820 (45,900) 18800 (41,500) 19970 (44,030) 21490 (47,380)
TRACTOR WEIGHT kg (lb) 17090 (37,680) 14280 (31,490) 13850 (30,530) 15620 (34,440)
FLYWHEEL HORSEPOWER HP (kW)/RPM 190 (142)/1950 155 (116)/1850 185 (138)/1850 215 (161)/1950
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 3.9 (2.4) 3.4 (2.1) 2.6 (1.6) 3.9 (2.4)
2nd 6.8 (4.2) 5.8 (3.6) 3.2 (2.0) 6.8 (4.2)
3rd 10.6 (6.6) 9.0 (6.0) 4.7 (2.9) 10.6 (6.6)
Reverse 1st 5.0 (3.1) 4.4 (2.7) 3.3 (2.1) 5.0 (3.1)
2nd 8.6 (5.3) 7.6 (4.7) 4.2 (2.6) 8.6 (5.3)
3rd 13.4 (8.3) 11.3 (7.0) 6.1 (3.8) 13.4 (8.3)
Max. drawbar pull kg (lb/kN) — 19190 —
(42,310/188)
DIMENSIONS:
Overall length (tractor) mm (ft.in) 4365 (14'4") 4100 (13'5") 4075 (13'4") 4135 (13'7'')
Overall length* mm (ft.in) 5845 (19'2") 6120 (20'1") 5230 (17'2") 5930 (19'5")
Overall width (w/o trunnion) mm (ft.in) 2390 (7'10") 2535 (8'4") 2490 (8'2") 2660 (8'9'')
Overall width (with blade)* mm (ft.in) 3460 (11'6") 3275 (10'9") 4100 (13'5") 4370 (14'4")
Overall height (tractor)** mm (ft.in) 2330 (7'8") 2305 (7'7") 2385 (7'10") 2375 (7'10'')
Overall height* mm (ft.in) 3220 (10'9") 3135 (10'3") 3020 (9'11") 2560 (8'5")
Track gauge mm (ft.in) 1880 (6'2") 1925 (6'4") 1880 (6'2") 2050 (6'9'')
Length of track on ground mm (ft.in) 3285 (10'9") 2930 (9'7") 2635 (8'8") 2980 (9'9'')
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SA6D125E S6D114E 6D125 S6D125
No.of cylinders- mm (in) 6 -125 × 150 4 -114 x 135 6-125 × 150 6-125 × 150
bore × stroke (4.92 × 5.91) (4.49 x 5.31) (4.92 × 5.91) (4.92 × 5.91)
Piston displacement ltr. (cu.in) 11.04 (674) 8.27 (505) 11.04 (674) 11.04 (674)
UNDERCARRIAGE:
No.of rollers (carrier/track) 2/8 2/7 2/7 2/8
Width of standard shoe mm (in) 510 (20.1) 610 (24") 610 (24.0) 610 (24.0)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 415 (109.6) 315 (93.3) 320 (84.5) 407 (107.5)
*) Spec conditions:
Bulldozer Semi-U tilt PAT Angledozer Angledozer
Rear attachment — Winch Winch Winch
Upper attachment Steel cab, ROPS Sweep canopy Sweep canopy Sweep canopy
** : Without canopy, exhaust pipe, pre-cleaner cap or other easily removed encumbrances.
*** : Travel speed km/h (ft.in) of D70LE-8: Forward 4th: 7.0 (4.3), 5th: 10.3 (6.4), Reverse 4th: 9.1 (5.7)
*4 : Long track spec.
1A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Specifications CRAWLER-TYPE
TRACTORS
Model
D85ESS-2A D85EX-15 D155A-5 D155AX-5
Item
OPERATING WEIGHT* kg (lb) 20670 (45,580) 28000 (61,735) 38700 (85,320) 38800 (85,540)
TRACTOR WEIGHT kg (lb) 15420 (34,000) 21040 (46,380) 27900 (61,510) 29400 (64,820)
FLYWHEEL HORSEPOWER HP (kW)/RPM 200 (149)/1950 240 (179)/1900 302 (225)/1900 310 (231)/1900
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 3.9 (2.4) 3.6 (2.2) 3.7 (2.3) 3.5 (2.2)
2nd 6.8 (4.2) 6.1 (3.8) 6.7 (4.2) 6.2 (3.9)
3rd 10.6 (6.6) 10.1 (6.3) 11.0 (6.8) 10.8 (6.7)
Reverse 1st 5.0 (3.1) 4.7 (2.9) 5.0 (3.1) 4.8 (3.0)
2nd 8.6 (5.3) 8.0 (5.0) 8.2 (5.1) 8.4 (5.2)
3rd 13.4 (8.3) 13.0 (8.1) 13.9 (8.6) 13.9 (8.6)
Max. drawbar pull kg (lb/kN) — — — —
DIMENSIONS:
Overall length (tractor) mm (ft.in) 4150 (13'7") 5035 (16'6") 4975 (16'4") 4865 (16'0")
Overall length* mm (ft.in) 7150 (23'6") 7255 (23'10") 8155 (26'9") 8155 (26'9")
Overall width (w/o trunnion) mm (ft.in) 2560 (8'5") 2560 (8'5") 2695 (8'10") 2695 (8'10")
Overall width (with blade)* mm (ft.in) 4370 (14'4") 3635 (11'11") 3955 (13'0") 3955 (13'0")
Overall height (tractor)** mm (ft.in) 2375 (7'10") 3163 (10'5") 2590 (8'6") 2555 (8'5")
Overall height* mm (ft.in) 2995 (9'10") 3330 (10'11") 3500 (11'6") 3500 (11'6")
Track gauge mm (ft.in) 2050 (6'9") 2000 (6'7") 2100 (6'11") 2100 (6'11")
Length of track on ground mm (ft.in) 2980 (9'9") 3050 (10') 3210 (10'6") 3210 (10'6")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model S6D125 SA6D125E SA6D140E SA6D140E
No.of cylinders- mm (in) 6-125 × 150 6-125 x 150 6-140 × 165 6-140 × 165
bore × stroke (4.92 × 5.91) (4.9 x 5.9) (5.51 × 6.50) (5.51 × 6.50)
Piston displacement ltr. (cu.in) 11.04 (674) 11.04 (674) 15.24 (930) 15.24 (930)
UNDERCARRIAGE:
No.of rollers (carrier/track) 2/8 2/7 2/6 2/6
Width of standard shoe mm (in) 510 (20.1) 560 (22") 560 (22.0) 560 (22.0)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 406 (107) 490 (129) 500 (132) 625 (165)
*) Spec conditions:
Bulldozer Angledozer Semi-U tilt Semi-U tilt Semi-U tilt
Rear attachment Multi-shank ripper Multi-shank ripper Multi-shank ripper Giant ripper
Upper attachment Canopy Steel cab, ROPS Steel cab, ROPS Steel cab, ROPS
Model
D155A-2A D275A-5 D275AX-5 D375A-5
Item
OPERATING WEIGHT* kg (lb) 34560 (76,190) 49850 (109,900) 49850 (109,900) 66990 (147,690)
TRACTOR WEIGHT kg (lb) 27870 (61,440) 37680 (83,070) 37680 (83,070) 49800 (109,790)
FLYWHEEL HORSEPOWER HP (kW)/RPM 320 (239)/2000 410 (306)/2000 410 (306)/2000 525 (391)/1800
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 3.7 (2.3) 3.8 (2.4) 3.8 (2.4) 3.8 (2.4)
2nd 6.8 (4.2) 6.7 (4.2) 6.7 (4.2) 6.8 (4.2)
3rd 11.8 (7.3) 11.2 (7.0) 11.2 (7.0) 11.8 (7.3)
Reverse 1st 4.5 (2.8) 4.9 (3.0) 4.9 (3.0) 5.1 (3.2)
2nd 8.2 (5.1) 8.7 (5.4) 8.7 (5.4) 9.2 (5.7)
3rd 13.7 (8.5) 14.9 (9.3) 14.9 (9.3) 15.8 (9.8)
Max. drawbar pull kg (lb/kN) — — — —
DIMENSIONS:
Overall length (tractor) mm (ft.in) 5080 (16'8") 5255 (17'3") 5255 (17'3") 5770 (18'11")
Overall length* mm (ft.in) 6560 (21'6") 9290 (30'6") 9260 (30'5") 10330 (33'11")
Overall width (w/o trunnion) mm (ft.in) 2810 (9'3") 2925 (9'7") 2925 (9'7") 3220 (10'7")
Overall width (with blade)* mm (ft.in) 4130 (13'7") 4300 (14'1") 4300 (14'1") 4695 (15'5")
Overall height (tractor)** mm (ft.in) 2755 (9') 3160 (10'4") 3160 (10'4") 3280 (10'9")
Overall height* mm (ft.in) 3690 (12'1") 3985 (13'1") 3985 (13'1") 4230 (13'11")
Track gauge mm (ft.in) 2140 (7') 2260 (7'5") 2260 (7'5") 2500 (8'2")
Length of track on ground mm (ft.in) 3150 (10'4") 3480 (11'5") 3480 (11'5") 3840 (12'7")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SA6D140E SDA6D140E SDA6D140E SA6D170E
No.of cylinders- mm (in) 6-140 × 165 6-140 × 165 6-140 × 165 6-170 × 170
bore × stroke (5.51 × 6.50) (5.51 × 6.50) (5.51 × 6.50) (6.69 × 6.69)
Piston displacement ltr. (cu.in) 15.24 (930) 11.04 (674) 11.04 (674) 23.15 (1413)
UNDERCARRIAGE:
No.of rollers (carrier/track) 2/7 2/7 2/7 2/7
Width of standard shoe mm (in) 560 (22.0) 610 (24.0) 610 (24.0) 610 (24.0)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 600 (159) 840 (222) 840 (222) 1050 (277)
*) Spec conditions:
Bulldozer Semi-U tilt Semi-U tilt Semi-U tilt Semi-U tilt
Rear attachment — Giant ripper Giant ripper Giant ripper
Upper attachment — Steel cab, ROPS Steel cab, ROPS Steel cab, ROPS
** : Without canopy, exhaust pipe, pre-cleaner cap or other easily removed encumbrances.
1A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Specifications CRAWLER-TYPE
TRACTORS
Model
D475A-5 D475A-3 SD D575A-3 D575A-3 SD
Item
OPERATING WEIGHT* kg (lb) 102500 (226,010) 108080 (238,270) 131350 (289,570) 152600 (336,420)
TRACTOR WEIGHT kg (lb) 77390 (170,610) 78590 (173,260) 98450 (217,040) 114580 (252,600)
FLYWHEEL HORSEPOWER HP (kW)/RPM 860 (641)/2000 860 (641)/2000 1050 (783)/1800 1150 (858)/1800
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 3.5 (2.2) 3.5 (2.2) 3.7 (2.3) 3.7 (2.3)
2nd 6.3 (3.9) 6.3 (3.9) 6.6 (4.1) 6.6 (4.1)
3rd 10.9 (6.8) 10.9 (6.8) 11.6 (7.2) 11.6 (7.2)
Reverse 1st 4.7 (2.9) 4.7 (2.9) 4.3 (2.7) 4.3 (2.7)
2nd 8.4 (5.2) 8.4 (5.2) 7.7 (4.8) 7.7 (4.8)
3rd 14.3 (8.9) 14.3 (8.9) 13.3 (8.3) 13.3 (8.3)
Max. drawbar pull kg (lb/kN) — — — —
DIMENSIONS:
Overall length (tractor) mm (ft.in) 6680 (21'11") 6680 (21'11") 7270 (23'10") 7695 (25'3")
Overall length* mm (ft.in) 11565 (37'11") 10525 (34'6") 12095 (39'8") 11720 (38'5")
Overall width (w/o trunnion) mm (ft.in) 3610 (11'10") 3610 (11'10") 4180 (13'9") 4180 (13'9")
Overall width (with blade)* mm (ft.in) 5265 (17'3") 6465 (21'3") 5880 (19'3") 7400 (24'3")
Overall height (tractor)** mm (ft.in) 3660 (12') 3660 (12') 3780 (12'5") 3780 (12'5")
Overall height* mm (ft.in) 4590 (15'1") 4590 (15'1") 4880 (16'0") 4880 (16'0")
Track gauge mm (ft.in) 2770 (9'1") 2770 (9'1") 3220 (10'7") 3220 (10'7")
Length of track on ground mm (ft.in) 4365 (14'4") 4365 (14'4") 4530 (14'10") 5485 (18')
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SDA12V140 SDA12V140 SA12V170 SA12V170
No.of cylinders- mm (in) 12-140 × 140 12-140 × 165 12-170 × 170 12-170 × 170
bore × stroke (5.51 × 6.50) (5.51 × 6.50) (6.69 × 6.69) (6.69 × 6.69)
Piston displacement ltr. (cu.in) 30.48 (1860) 30.48 (1860) 46.3 (2825) 46.3 (2825)
UNDERCARRIAGE:
No.of rollers (carrier/track) 2/7 2/7 2/6 2/8
Width of standard shoe mm (in) 710 (28.0) 810 (32.0) 860 (34.0) 860 (33.9)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 1670 (441) 1670 (441) 2100 (555) 2100 (555)
*) Spec conditions:
Bulldozer Semi-U tilt Super dozer Semi-U dozer Super dozer
Rear attachment Giant ripper Counterweight Giant ripper Counterweight
Upper attachment Steel cab, ROPS Steel cab, ROPS Steel cab, ROPS Steel cab, ROPS
Other Air conditioner
** : Without canopy, exhaust pipe, pre-cleaner cap or other easily removed encumbrances.
1A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Specifications CRAWLER-TYPE
(Low Ground Pressure Tractors) TRACTORS
Model
D21P-7 D31PX-21 D31PX-7*** D37PX-21
Item
OPERATING WEIGHT* kg (lb) 4100 (9,040) 7650 (16,870) 7650 (16,870) 7770 (17,130)
TRACTOR WEIGHT kg (lb) 3520 (7,760) 6220 (13,710) 6220 (13,710) 6310 (13,910)
FLYWHEEL HORSEPOWER HP (kW)/RPM 40 (29.5)/2450 75 (56)/2000 75 (56)/2000 85 (63)/2000
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 2.6 (1.6) 3.4 (2.1) 0.8 (0.5) to 3.4 (2.1)
2nd 4.4 (2.7) 5.6 (3.5) 8.5 (5.3) 5.6 (3.5)
3rd — 8.5 (5.3) — 8.5 (5.3)
Reverse 1st 3.3 (2.1) 4.1 (2.5) 0.8 (0.5) to 4.1 (2.5)
2nd 5.6 (3.5) 6.5 (4.0) 8.5 (5.3) 6.5 (4.0)
3rd — 8.5 (5.3) — 8.5 (5.3)
Max. drawbar pull kg (lb/kN) 4480 12500 4480 12500
(9,880/43.9) (27,560/123) (9,880/43.9) (27,560/123)
DIMENSIONS:
Overall length (tractor) mm (ft.in) 2430 (8'0") 3090 (10'2") 3090 (10'2") 3055 (10'0")
Overall length* mm (ft.in) 3260 (10'8") 3995 (13'1") 3995 (13'1") 3995 (13'1")
Overall width (w/o trunnion) mm (ft.in) 2000 (6'7") 2250 (7'5") 2250 (7'5") 2250 (7'5")
Overall width (with blade)* mm (ft.in) 2560 (8'5") 3200 (10'6") 3200 (10'6") 3250 (10'8")
Overall height (tractor)** mm (ft.in) 1810 (5'11") 1890 (6'2") 1890 (6'2") 1890 (6'2")
Overall height* mm (ft.in) 2335 (7'8") 2700 (8'10") 2700 (8'10") 2700 (8'10")
Track gauge mm (ft.in) 1490 (4'11") 1650 (5'5") 1650 (5'5") 1650 (5'5")
Length of track on ground mm (ft.in) 1685 (5'6") 2185 (7'2") 2185 (7'2") 2240 (7'4")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model 4D94LE SAA4D102E SAA4D102E SAA4D102E
No.of cylinders- mm (in) 4-94 × 110 4-102 × 120 4-102 × 120 4-102 × 120
bore × stroke (3.70 × 4.33) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 3.053 (186) 3.92 (239) 3.92 (239) 3.92 (239)
UNDERCARRIAGE:
No.of rollers (carrier/track) 1/5 1/6 1/6 1/6
Width of standard shoe mm (in) 510 (20.1) 600 (23.6) 600 (23.6) 600 (23.6)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 60 (15.9) 165 (43.6) 165 (43.6) 165 (43.6)
*) Spec conditions:
Bulldozer PAT PAT PAT PAT
Rear attachment — — — —
Upper attachment — ROPS canopy ROPS canopy ROPS canopy
Model
D37PX-21*** D39PX-21 D39PX-21*** D41P-6
Item
OPERATING WEIGHT* kg (lb) 7770 (17,130) 8900 (19,620) 8900 (19,620) 11340 (25,000)
TRACTOR WEIGHT kg (lb) 6310 (13,910) 7230 (15,940) 7230 (15,940) 9370 (20,660)
FLYWHEEL HORSEPOWER HP (kW)/RPM 85 (63)/2000 95 (71)/2200 95 (71)/2200 110 (82)/2300
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 0.8 (0.5) to 3.4 (2.1) 0.8 (0.5) to 2.4 (1.5)
2nd 8.5 (5.3) 5.6 (3.5) 8.5 (5.3) 4.4 (2.7)
3rd — 8.5 (5.3) — 7.6 (4.7)
Reverse 1st 0.8 (0.5) to 4.1 (2.5) 0.8 (0.5) to 3.0 (1.9)
2nd 8.5 (5.3) 6.5 (4.1) 8.5 (5.3) 5.5 (3.4)
3rd — 8.5 (5.3) — 9.4 (5.8)
Max. drawbar pull kg (lb/kN) 12500 13800 13800 14700
(27,560/123) (30,420/135) (30,420/135) (32,410/144.2)
DIMENSIONS:
Overall length (tractor) mm (ft.in) 3055 (10'0") 3195(10'6") 3195(10'6") 3610 (11'10")
Overall length* mm (ft.in) 3995 (13'1") 3995 (13'1") 3995 (13'1") 4880 (16'0")
Overall width (w/o trunnion) mm (ft.in) 2250 (7'5") 2425 (7'11") 2425 (7'11") 2490 (8'2")
Overall width (with blade)* mm (ft.in) 3250 (10'8") 3330 (10'11") 3330 (10'11") 3045 (11'0")
Overall height (tractor)** mm (ft.in) 1890 (6'2") 1965 (6'5") 1965 (6'5") 2020 (6'8")
Overall height* mm (ft.in) 2700 (8'10") 2770 (9'1") 2770 (9'1") 2885 (9'6")
Track gauge mm (ft.in) 1650 (5'5") 1790 (5'10") 1790 (5'10") 1790 (5'10")
Length of track on ground mm (ft.in) 2240 (7'4") 2360 (7'9") 2360 (7'9") 2745 (9')
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA4D102E SAA4D102E SAA4D102E SA6D102E
No.of cylinders- mm (in) 4-102 × 120 4-102 × 120 4-102 × 120 6-102 × 120
bore × stroke (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 3.92 (239) 3.92 (239) 3.92 (239) 5.88 (359)
UNDERCARRIAGE:
No.of rollers (carrier/track) 1/6 1/6 1/6 1/7
Width of standard shoe mm (in) 600 (23.6) 635 (25.0) 635 (25.0) 700 (27.6)
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 165 (43.6) 165 (43.6) 165 (43.6) 250 (66.0)
*) Spec conditions:
Bulldozer PAT PAT PAT PAT
Rear attachment — — — —
Upper attachment ROPS canopy ROPS canopy ROPS canopy ROPS canopy
** : Without canopy, exhaust pipe, pre-cleaner cap or other easily removed encumbrances.
*** : Variable travel speed mode
1A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Specifications CRAWLER-TYPE
(Low Ground Pressure Tractors) TRACTORS
Model
D61PX-12 D65P-12 D65PX-15 D85PX-15
Item
OPERATING WEIGHT* kg (lb) 17500 (38,580) 20185 (44,500) 20800 (45,860) 27550 (60,740)
TRACTOR WEIGHT kg (lb) 14550 (32,080) 16940 (37,350) 17330 (38,210) 23320 (51,410)
FLYWHEEL HORSEPOWER HP (kW)/RPM 150 (112)/1800 190 (142)/1950 190 (142)/1950 240 (179)/1900
PERFORMANCE:
Travel speed Forward 1st km/h (MPH) 3.5 (2.2) 3.9 (2.4) 3.9 (2.4) 3.6 (2.2)
2nd 6.0 (3.7) 6.8 (4.2) 6.8 (4.2) 6.0 (3.7)
3rd 10.3 (6.4) 10.6 (6.6) 10.6 (6.6) 10.0 (6.2)
Reverse 1st 4.6 (2.9) 5.0 (3.1) 5.0 (3.1) 4.7 (2.9)
2nd 7.9 (4.9) 8.6 (5.3) 8.6 (5.3) 7.9 (4.9)
3rd 12.8 (8.0) 13.4 (8.3) 13.4 (8.3) 12.7 (7.9)
Max. drawbar pull kg (lb/kN) — — — —
DIMENSIONS:
Overall length (tractor) mm (ft.in) 4160 (13'8") 4425 (14'6") 4425 (14'6") 4720 (15'6")
Overall length* mm (ft.in) 5440 (17'10") 5520 (18'1") 5520 (18'1") 6065 (19'11")
Overall width (w/o trunnion) mm (ft.in) 3000 (9'10") 2965 (9'9") 2965 (9'9") 3160 (10'4")
Overall width (with blade)* mm (ft.in) 3860 (12'8") 3970 (13'0") 3970 (13'0") 4365 (14'4")
Overall height (tractor)** mm (ft.in) 2195 (7'2") 2300 (7'7") 2300 (7'7") 3200 (10'6")
Overall height* mm (ft.in) 3115 (10'3") 3165 (10'5") 3220 (10'7") 3330 (10'11")
Track gauge mm (ft.in) 2140 (7') 2050 (6'9") 2050 (6'9") 2250 (7'5")
Length of track on ground mm (ft.in) 3170 (10'5") 3285 (10'9") 3285 (10'9") 3480 (11'5")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SA6D114E S6D125E SA6D125E SA6D125E
No.of cylinders- mm (in) 6-114 × 135 6-125 × 150 6-125 × 150 6-125 x 150
bore × stroke (4.49 × 5.31) (4.92 × 5.91) (4.92 × 5.91) (4.9 x 5.9)
Piston displacement ltr. (cu.in) 8.27 (505) 11.04 (674) 11.04 (674) 11.04 (674)
UNDERCARRIAGE:
No.of rollers (carrier/track) 2/8 2/8 2/8 2/8
Width of standard shoe mm (in) 860 (33.9) 915 (36.0) 915 (36.0) 910 (36")
FUEL TANK CAPACITY (Refilled): ltr. (U.S.Gal) 337 (89.0) 406 (107.3) 415 (109.6) 490 (129)
*) Spec conditions:
Bulldozer PAT Straight tilt Straight tilt Straight tilt
Rear attachment — — — —
Upper attachment ROPS canopy Steel cab, ROPS Steel cab, ROPS Steel cab, ROPS
** : Without canopy, exhaust pipe, pre-cleaner cap or other easily removed encumbrances.
1A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
US ton kN ton
kN
50
240 24
52
50
220 48 22
400 40
200 44 20
40
180 40 18
F1
F1
Drawbar Pull
Drawbar pull
160 36 16 300 30
32 30
140 14
F2
28
120 12
24 200 20
100 10 20
F2
20 F3
80 8
16
100 10
60 6 10
12
40 4 F3
8
20 4 2 0 0 0
0 2 4 6 8 10 12 km/h
0 0 0
0 2 4 6 8 10 12 14 km/h 0 1 2 3 4 5 6 7 mph
0 2 4 6 8 mph
Travel Speed
Travel speed FVDM1370
200 F1
DRAWBAR PULL
20 30
300 60 F1
40
F2
F2 200 20
40
100 10 F3
20
F3
100 20 10
0 0 0
0 0 0 0 2 4 6 8 10 km/h
0 2 4 6 8 10 12 14 km/h
0 1 2 3 4 5 6 MPH
0 1 2 3 4 5 6 7 8 MPH
D85EX-15 D155A-5
USton
3 3
x kN x 10 lbkg x 10 kg
ton
kN
70 44 480 48
700
140
40 440 44
60
600
120 36 400 40
32 360 36
DRAWBAR PULL
50
500 100 320 32
DRAWBAR PULL
28 F1
F1
40 280 28
400 80 24
240 24
F2 20
300 60
30 200 20
16 F2
160 16
200 20 F3 12
40 120 12
8 80 8
100 20 10 F3
4 40 4
0 0 0 0 0 0
0 2 4 6 8 10 12 14 km/h
0 2 4 6 8 10 12 14 16 18 20km/h
0 1 2 3 4 5 6 7 8 MPH
0 2 4 6 8 10 12 MPH
TRABEL SPEED 0
FVBH0264 Travel speed
NOTE: THE DRAWBAR PULL AND TRAVEL SPEED MAY BE SUBJECT TO CHANGE DEPENDING ON
THE GROUND CONDITIONS AND MACHINE WEIGHT.
1A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
lb x 103
ton
kN
Ton
kN
480 48
44 500 120 50
440 44
40 450 100 45
400 40
36 90 40
360 36 400
32 80
320 32 350 35
28 F1 70
Drawbar pull
280 28 300 30 F1
Rimpull
24 240 24 60
250 25
20 200 20 50
200 20 F2
16 160 16 F2 40
150 15
12 120 12 30
F3
8 80
100 20 10
8 F3
4 40 4 50 10 5
0 0 0 0 0 0
0 2 4 6 8 10 12 14 16 18 20 km/h 0 2 4 6 8 10 12 14km/h
0 2 4 6 8 10 12 MPH 0 2 4 6 8 MPH
0
Travel speed Travel speed
D275A-5 D275AX-5
US ton kN ton US ton kN ton
60 60
60 60
F1 F1
500 500
50 50
50 F2 50 F2
400 40 400 40
40 40
Drawbar Pull
Drawbar Pull
F3 F3 F1 Lockup
300 300
30 30
30 30
F3 Lockup
100 10 100 10
10 10
0 0 0 0 0 0
0 2 4 6 8 10 12 km/h 0 2 4 6 8 10 12 km/h
0 1 2 3 4 5 6 7 mph 0 1 2 3 4 5 6 7 mph
Travel Speed Travel Speed
x 103 lb x 103 kg
Ton
kN
250
110 1200130 120
200 90 1000110100
F1 (T/C
80 900100 90
)
DRAWBAR PULL
F1
70 800 90 80
150
700 80 70
DRAWBAR PULL
60 F1(LOCK UP)
F2
70
(T/C
600 60
50
)
100 60
500 50 F2
40 50
F1 (LOCK UP)
F3 400 40 F2(LOCK UP)
30 (T
/C 40
)
50 F2 (LOCK UP) 300 30
20 30 F3
F3(LOCK UP)
200 20 20
F3 (LOCK UP)
10
100 10 10
0 0
0 2 4 6 8 10 12 km 0 0
0
0 2 4 6 8 10 12 14 km/h
0 1 2 3 4 5 6 7 8 mph 0 2 4 6 8 mph
TRAVEL SPEED TRAVEL SPEED
FZD00358
NOTE: THE DRAWBAR PULL AND TRAVEL SPEED MAY BE SUBJECT TO CHANGE DEPENDING ON
THE GROUND CONDITIONS AND MACHINE WEIGHT.
1A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
ton
kN
120
1000 100 F2
100 F2(Lockup)
800 80
80
F3
600 60
60
400 40
40
20 200 20
0 0 0
0 2 4 6 8 10 12 km/h
0 2 4 6 MPH
TRAVEL SPEED FVBH0252
D61PX-12 D65PX-15
kg x 103
lb x 103
US ton kN ton
50
kN
240 24
52 50
220 48 22
400 40
200 44 20
40
180 40 18 F1
Drawbar Pull
F1 300
Drawbar pull
160 36 16 30
32 30
140 14 F2
28
120 12
200 20
24 20
100 10
20
F2 F3
80 8
16
100 10
60 6 10
12
40 4 F3
8
20 4 2 0 0 0
0 2 4 6 8 10 12 km/h
0 0 0
0 2 4 6 8 10 12 14 km/h 0 1 2 3 4 5 6 7 mph
0 2 4 6 8 mph
Travel Speed
Travel speed FVDM1370
D85PX-15
3 3
x kN x 10 lbkg x 10 kg
70
700
140
60
600
120
DRAWBAR PULL
50
500 100
F1
40
400 80
F2
300 30
60
200 20 F3
40
100 20 10
0 0 0
0 2 4 6 8 10 12 14 km/h
0 1 2 3 4 5 6 7 8 MPH
TRABEL SPEED
FVBH0264A
NOTE: THE DRAWBAR PULL AND TRAVEL SPEED MAY BE SUBJECT TO CHANGE DEPENDING ON
THE GROUND CONDITIONS AND MACHINE WEIGHT.
1A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
1A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
1A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
1A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
3 • Tripple grouser shoe • The three grousers have • This shoe does not readily
• Double grouser shoe the same height, hence bite into the ground, so the
Hard ground turning ability is good. traction force is low.
Suitable for both soft • Good riding comfort is
and hard ground obtained as compared with
(for hydraulic a single grouser shoe.
excavator and dozer • Rotating resistance is low.
shovel) • Because three beams are
used, resistance to
bending is high.
4 Swamp shoe • Because the cross-section • Unsuitable for ground other Various widths are
of this shoe is an arc, the than swampy ground. available to suit
ground contact area is When used off swampy the degree of
large, and buoyancy is ground, it is liable to bend softness of the
easily obtained. due to its low strength. swampy ground.
• This shoe is particularly
suitable for use in swamp
Swamp areas areas and areas with low
(for swamp dozer) ground pressure. The
ground surface is not
damaged when the
machine travels over it, so
it is suitable for soil
compaction and leveling
work.
1A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
1A-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
Local
add-on type
Determination criterion for
different working environments
Rocks and soil containing boulders The part is effective for prevention of catching pebbles.
and gravel (A and E)
Sand and sandy soil The part is effective for prevention of pitch squeaking.
(A, E and P)
Clayey soil (P and PL) Be careful when using this part since the soil sets when dried. (Note 1)
Swamp (PL and PLL) The part is effective for prevention of snaking of the track.
(Prevents side sliding of the track shoes.) (Note 1)
The part is effective for prevention of disengagement of the track shoes.
Slopes The part is effective for prevention of disengagement of the track shoes.
(Prevents side-sliding of the track shoes.)
(Note 1) Although soil and sand tend to enter less, once they enter, they may not be easily discharged
depending on the type of soil, so make the choice in consideration of past experience with machines
having been used in the subject area and of the working environments of the machine.
NOTE: Please consult your local distributor for availability of track rollers guard for the model that you
require.
1A-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
Large Class
When using bulldozers, it is necessary to make most appropriate choices of the track roller guards fitting to
respective working environments. Given below are the criterion for the choices.
This chart provides clearer criterion for the choices in consideration of respective functions of different
types of track roller guards.
(Note 1) Although soil and sand tend to enter less, once they enter, they may not be easily discharged depending on the
type of soil, so make the choice in consideration of past experience with machines having been used in the
subject area and of the working environments of the machine.
NOTE: Please consult your local distributor for availability of track rollers guard for the model that you
require.
1A-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
G.L
1A-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 1B
BULLDOZERS
CONTENTS
Blade selection ......................................................... 1B-2
Blade availability ...................................................... 1B-3
Blade specifications:
Straight-tiltdozer .................................................. 1B-5
Angledozer ........................................................... 1B-6
Power angle-tiltdozer .......................................... 1B-8
Semi-U-tildozer .................................................. 1B-11
U-tildozer ............................................................ 1B-13
Super dozer ........................................................ 1B-14
Coal dozer .......................................................... 1B-15
Production .............................................................. 1B-16
1B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Straight-tilltdozer
Having a high HP/ cutting edge length, this blade
has an aggressive penetration. This blade also has a
high HP/loose cubic yards for easy handling of
heavy materials. The tilting function of this blade
increases production and versatility. With a sturdy
construction, this blade is suitable for powerful
cutting and dozing, especially heavy cutting on rocky
ground.
Straight dozer
This blade has the same structure and functions but
is not equipped with a tilt-cylinder.
Angle dozer
The blade can be set straight or angled to both
sides. Plowing earth or snow to one side is possible
by angling the blade.
Useful for road construction, back filling etc.
Power angle-tiltdozer
Power angling and tilting of the blade are possible
from the operator seat. This blade is applicable for
versatile works such as grading, back filling,
spreading and light land clearing
Dual tiltdozer
The blade has two tilt cylinders on both sides. An
optimum blade cutting angle for all types of materials
and ground inclinations can be selected for
increased loads and consequently increased
production. A fast tilt speed and a large tilt angle also
concentrate blade force where maximum
penetration is needed.
Semi U-tiltdozer
The blade combines penetration ability of straight
blade with increased load capacity provided by short
wings which include only the end bits.
U-tiltdozer
The wings on this blade minimize material spillage.
Since this blade has a lower HP/loose cubic yards
than a straight-tiltdozer, this blade is suitable for
moving lighter or loose materials over long
distances.
Suitable works are land reclamation, stockpiling and
other similar jobs.
Coal dozer
Specialized blade for pushing coal, with larger width FVBH0199
and deep angled wings.
Rake-dozer
Having teeth, this blade provides good penetration
into the soil for removal of stumps, roots and rocks.
1B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
1B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
1B-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
F G.L
B A
Model
D65E-12 D65P-12 D65EX-15 D65PX-15
Item
OPERATING WEIGHT* kg (lb) 17470 (38,510) 18860 (41,580) 19070 (42,040) 20700 (45,635)
BLADE CAPACITY LH2** m3 (yd3) 5.12 (6.70) 4.80 (6.28) 5.12 (6.70) 4.80 (6.28)
SAE 3.89 (5.09) 3.69 (4.83) 3.89 (5.09) 3.69 (4.83)
DIMENSION*
A Overall length mm (ft.in) 5260 (17'3") 5550 (18'3") 5260 (17'3") 5220 (18'1")
B Overall width mm (ft.in) 3415 (11'2") 3970 (13') 3415 (11'2") 3970 (13')
C Overall height mm (ft.in) 2980 (9'9") 3025 (9'11") 2990 (9'10") 2990 (9'10")
Ground pressure kg/cm2 (PSI) 0.64 (9.10) 0.30 (4.27) 0.70 (9.95) 0.33 (4.69)
DOZER EQUIPMENT
Weight kg (lb) 2600 (5,730) 2620 (5,780) 2720 (5,995) 2740 (6,040)
(Includes hydraulic control unit) 2720 (6,000)
Length mm (ft.in) 3415 (11'2") 3970 (13') 3415 (11'2") 3970 (13'0")
Height mm (ft.in) 1225 (4'1") 1100 (3'7") 1225 (4'0") 1100 (3'7")
D Max. lift above ground mm (ft.in) 1100 (3'7") 1200 (3'11") 1105 (3'8") 1105 (3'8")
E Max. drop below ground mm (ft.in) 450 (1'6") 445 (1'6") 440 (1'5") 540 (1'9")
F Max. tilting adjustment mm (ft.in) 870 (2'10") 890 (2'11") 870 (2'10") 450 (1'6")
Digging angle degree 55 57 55 57
Model
D85E-SS-2A D85EX-15 D85PX-15
Item
OPERATING WEIGHT* kg (lb) 18230 (40,190) 24370 (53,730) 26690 (58,840)
BLADE CAPACITY LH2** m3 (yd3) 6.1 (7.98) 7.7 (10.07) 8.2 (10.73)
SAE 4.4 (5.76) 5.2 (6.8) 5.9 (7.7)
DIMENSION*
A Overall length mm (ft.in) 5615 (18'5") 5640 (18'6") 6065 (19'11")
B Overall width mm (ft.in) 3620 (11'11") 3715 (12'2") 4365 (14'4")
C Overall height mm (ft.in) 2980 (9'9") 3330 (10'11") 3330 (10'11")
Ground pressure kg/cm2 (PSI) 0.60 (8.53) 0.74 (10.5) 0.43 (6.1)
DOZER EQUIPMENT
Weight kg (lb) 2810 (6,190) 3305 (7,290) 3345 (7,375)
(Includes hydraulic control unit)
Length mm (ft.in) 3620 (11'11") 3715 (12'2") 4365 (14'4")
Height mm (ft.in) 1295 (4'3") 1436 (4'9") 1370 (4'6")
D Max. lift above ground mm (ft.in) 1070 (3'6") 1207 (4') 1222 (4')
E Max. drop below ground mm (ft.in) 590 (1'11") 540 (1'9") 568 (1'10")
F Max. tilting adjustment mm (ft.in) 920 (3') 750 (2'6") 500 (1'8")
Digging angle degree 55 55 55
* : Including dozer equipment in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
1B-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
D
F
G.L
B A
Model
D68ESS-12*** D65E-12 D65EX-15 D70LE-6***
Item
OPERATING WEIGHT* kg (lb) 19100 (42,110) 17690 (39,000) 19280 (42,110) 19970 (44,030)
BLADE CAPACITY LH2** m3 (yd3) 3.6 (4.71) 4.80 (6.28) 4.80 (6.28) 4.5 (5.89)
SAE 2.6 (3.40) 3.55 (4.64) 3.55 (4.64) 3.1 (4.05)
DIMENSION*
A Overall length mm (ft.in) 5930 (19'5") 5470 (17'11") 5470 (17'11") 5230 (17'2")
B Overall width mm (ft.in) 3970 (13') 3970 (13') 3970 (13') 4100 (13'5")
C Overall height mm (ft.in) 3140 (10'4") 2980 (9'9") 2990 (9'10") 3020 (9'11")
Ground pressure kg/cm2 (PSI) 0.54 (7.68) 0.65 (9.2) 0.71 (10.1) 0.53 (7.54)
DOZER EQUIPMENT
Weight kg(lb) 2660 (5,860) 2820 (6,220) 2930 (5,860) 3090(6,810)
(Includes hydraulic control unit) 2930 (6,460)
Length mm (ft.in) 3970 (13') 3970 (13') 3970 (13') 4100 (13'5")
Height mm (ft.in) 950 (3'1") 1100 (3'7") 1100 (3'7") 1050 (3'5")
D Max. lift above ground mm (ft.in) 1205 (3'11") 1180 (3'10") 1185 (3'11") 1130 (3'8")
E Max. drop below ground mm (ft.in) 535 (1'9") 460 (1'6") 450 (1'6") 585 (1'11")
F Max. tilting adjustment mm (ft.in) 400 (1'4") 400 (1'4") 400 (1'4") 400 (1'4")
Digging angle degree 50 56.5 56.5 55
Model
D85ESS-2*** D85ESS-2A D85A-21
Item
OPERATING WEIGHT* kg (lb) 21490 (47,390) 18850 (41,560) 23320 (51,410)
BLADE CAPACITY LH2** m3 (yd3) 5.0 (6.54) 5.0 (6.54) 5.6 (7.32)
SAE 3.4 (4.45) 3.4 (4.45) 3.9 (5.10)
DIMENSION*
A Overall length mm (ft.in) 5930 (19'5") 5930 (19'5") 5810 (19'1")
B Overall width mm (ft.in) 4370 (14'4") 4370 (14'4") 4365 (14'4")
C Overall height mm (ft.in) 2560 (8'5") 2980 (9'9") 3365 (11')
Ground pressure kg/cm2 (PSI) 0.52 (7.39) 0.62 (8.82) 0.73 (10.38)
DOZER EQUIPMENT
Weight kg (lb) 2890 (6,370) 3430 (7,560) 4610 (10,160)
(Includes hydraulic control unit)
Length mm (ft.in) 4370 (14'4") 4370 (14'4") 4365 (14'4")
Height mm (ft.in) 1070 (3'6") 1070 (3'6") 1130 (3'8")
D Max. lift above ground mm (ft.in) 1255 (4'1") 1255 (4'1") 1310 (4'4")
E Max. drop below ground mm (ft.in) 485 (1'7") 485 (1'7") 560 (1'10")
F Max. tilting adjustment mm (ft.in) 400 (1'4") 400 (1'4") 500 (1'8")
Digging angle degree 56 56 55.6
* : Including dozer equipment in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
*** : With winch and sweep canopy
1B-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
D
F
G.L
B A
Model
D85A-21B D85E-21 D155A-2A D155A-5
Item
OPERATING WEIGHT* kg (lb) 22860 (50,400) 23680 (52,200) 34390 (75,820) 33040 (72,840)
BLADE CAPACITY LH2** m3 (yd3) 5.6 (7.32) 5.6 (7.32) 6.30 (8.64) 7.00 (9.16)
SAE 3.9 (5.10) 3.9 (5.10) 4.58 (5.99) 4.9 (6.4)
DIMENSION*
A Overall length mm (ft.in) 6100 (20') 6020 (19'9") 6620 (21'9") 6502 (21'4")
B Overall width mm (ft.in) 4365 (14'4") 4365 (14'4") 4850 (15'11") 4850 (15'11")
C Overall height mm (ft.in) 3365 (11') 3365 (11') 3725 (12'3") 3395 (11'2")
Ground pressure kg/cm2 (PSI) 0.75 (10.67) 0.69 (9.81) 0.975 (13.86) 0.92 (13.1)
DOZER EQUIPMENT
Weight kg (lb) 4610 (10,160) 4610 (10,160) 6520 (14,370) 5140 (11,330)
(Includes hydraulic control unit)
Length mm (ft.in) 4635 (14'4") 4365 (14'4") 4850 (15'11") 4850 (15'11")
Height mm (ft.in) 1130 (3'8") 1130 (3'8") 1140 (3'9") 1205 (3'11")
D Max. lift above ground mm (ft.in) 1310 (4'4") 1425 (4'8") 1520 (5') 1295 (4'3")
E Max. drop below ground mm (ft.in) 560 (1'10") 580 (1'11") 630 (2'1") 745 (2'5")
F Max. tilting adjustment mm (ft.in) 500 (1'8") 500 (1'8") 400 (1'4") 520 (1'8")
Digging angle degree 55.6 55.6 55 55
Model
D155AX-5
Item
OPERATING WEIGHT* kg (lb) 34540 (76,150)
DOZER EQUIPMENT
Weight kg (lb) 5140 (11,330)
(Includes hydraulic control unit)
Length mm (ft.in) 4850 (15'11")
Height mm (ft.in) 1205 (3'11")
D Max. lift above ground mm (ft.in) 1295 (4'3")
E Max. drop below ground mm (ft.in) 745 (2'5")
F Max. tilting adjustment mm (ft.in) 520 (1'8")
Digging angle degree 55
* : Including dozer equipment in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
1B-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
D
G.L
F
E
B A
Model
D21A-8 D21P-8 D31EX-21 D31PX-21
Item
OPERATING WEIGHT* kg (lb) 3710 (8,180) 4100 (9,040) 6820 (15,040) 7340 (16,180)
2 3 3
BLADE CAPACITY LH ** m (yd ) 0.76 (0.99) 0.89 (1.16) 1.74 (2.28) 1.80 (2.35)
SAE 0.57 (0.75) 0.68 (0.89) 1.49 (1.95) 1.55 (2.03)
DIMENSION*
A Overall length mm (ft.in) 3250 (10'8") 3260 (10'8") 4015 (13'2") 3995 (13'1")
B Overall width mm (ft.in) 2170 (7'11") 2560 (8'5") 2435 (8'0") 3200 (10'6")
C Overall height mm (ft.in) 2315 (7'7") 2335 (7'8") 2645 (8'8") 2645 (8'8")
Ground pressure kg/cm2 (PSI) 0.37 (5.26) 0.24 (3.41) 0.42 (5.97) 0.28 (3.98)
DOZER EQUIPMENT
Type Inside mount Inside mount Inside mount Inside mount
Weight kg (lb) 550 (1,210) 580 (1280) 1045 (2,300) 1120 (2,470)
(Includes hydraulic control unit)
Length mm (ft.in) 2170 (7'11") 2560 (8'5") 2435 (8'0") 3200 (10'6")
Height mm (ft.in) 590 (1'11") 590 (1'11") 845 (2'9") 750 (2'6")
D Max. lift above ground mm (ft.in) 790 (2'7") 850 (2'9") 860 (2'10") 855 (2'10")
E Max. drop below ground mm (ft.in) 385 (1'3") 325 (1'1") 385 (1'3") 380 (1'3")
F Max. tilting adjustment mm (ft.in) 250 (9'8") 280 (11") 330 (1'1") 435 (1'5")
Model
D37EX-21 D37PX-21 D39EX-21 D39PX-21
Item
OPERATING WEIGHT* kg (lb) 7100 (15,650) 7460 (16,450) 8210 (18,100) 8590 (18,940)
BLADE CAPACITY LH2** m3 (yd3) 2.04 (3.24) 2.24 (3.52) 2.63 (3.14) 2.78 (3.40)
SAE 1.75 (2.29) 1.91 (2.50) 2.22 (2.90) 2.32 (3.03)
DIMENSION*
A Overall length mm (ft.in) 4015 (13'2") 3995 (13'1") 4200 (13'9") 4200 (13'9")
B Overall width mm (ft.in) 2720 (8'11") 3250 (10'8") 2740 (9'0") 3330 (10'11'')
C Overall height mm (ft.in) 2645 (8'8") 2645 (8'8") 2720 (8'11") 2720 (8'11")
Ground pressure kg/cm2 (PSI) 0.40 (5.69) 0.28 (3.98) 0.38 (5.40) 0.29 (4.12)
DOZER EQUIPMENT
Type Inside mount Inside mount Inside mount Inside mount
Weight kg (lb) 1090 (2,400) 1150 (2,540) 1260 (2,780) 1360 (3,000)
(Includes hydraulic control unit)
Length mm (ft.in) 2720 (8'11") 3250 (10'8") 2740 (9'0") 3330 (10'11")
Height mm (ft.in) 865 (2'10") 830 (2'9") 980 (3'3") 910 (3'0")
D Max. lift above ground mm (ft.in) 860 (2'10") 855 (2'10") 890 (2'11") 890 (2'11")
E Max. drop below ground mm (ft.in) 385 (1'3") 380 (1'3") 440 (1'5") 440 (1'5")
F Max. tilting adjustment mm (ft.in) 375 (1'3") 445 (1'6") 395 (1'4") 480 (1'7")
1B-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
D
G.L
F
E
B A
Model
D41E-6 D41E-6*** D41P-6 D41P-6***
Item
OPERATING WEIGHT* kg (lb) 10590 (23,345) 10670 (25,145) 11170 (24,625) 11250 (24,805)
BLADE CAPACITY LH2** m3 (yd3) 3.4 (4.45) 3.8 (4.92) 3.4 (4.45) 3.8 (4.92)
SAE 2.6 (3.40) 2.9 (3.79) 2.6 (4.12) 2.9 (3.79)
DIMENSION*
A Overall length mm (ft.in) 4880 (16') 4880 (16') 4880 (16') 4880 (16')
B Overall width mm (ft.in) 3045 (10') 3350 (11') 3045 (10') 3350 (11')
C Overall height mm (ft.in) 2675 (8'9") 2675 (8'9") 2675 (8'9") 2675 (8'9")
Ground pressure kg/cm2 (PSI) 0.42 (5.97) 0.42 (5.97) 0.29 (4.12) 0.29 (4.12)
DOZER EQUIPMENT
Type Inside mount Inside mount Inside mount Inside mount
Weight kg (lb) 1800 (3,965) 1880 (4,145) 1800 (3,965) 1880 (4,145)
(Includes hydraulic control unit)
Length mm (ft.in) 3045 (10') 3350 (11') 3045 (10') 3350 (11')
Height mm (ft.in) 1060 (3'6") 1060 (3'6") 1060 (3'6") 1060 (3'6")
D Max. lift above ground mm (ft.in) 1010 (3'4") 1010 (3'4") 1010 (3'4") 1010 (3'4")
E Max. drop below ground mm (ft.in) 490 (1'7") 490 (1'7") 490 (1'7") 490 (1'7")
F Max. tilting adjustment mm (ft.in) L:485 (1'7") L:530 (1'9") L:485 (1'7") L:530 (1'9")
R:645 (2'1") R:710 (2'4") R:645 (2'1") R:710 (2'4")
Angling angle (L/R) degree 55/25 55/25 55/25 30/25
Model
D61EX-12 D61EX-12*** D61EX-12*4 D61PX-12
Item
OPERATING WEIGHT* kg (lb) 15470 (34,110) 15630 (34,460) 16250 (35,820) 17180 (32,880)
2 3 3
BLADE CAPACITY LH ** m (yd )
SAE 3.4 (4.4) 3.8 (5.0) 3.4 (4.4) 3.8 (5.0)
DIMENSION*
A Overall length mm (ft.in) 5030 (16'6") 5030 (16'6") 5440 (17'10") 5440 (17'10")
B Overall width mm (ft.in) 3275 (10'9") 3860 (12'8") 3275 (10'9") 3860 (12'8")
C Overall height mm (ft.in) 2945 (9'8") 2945 (9'8") 2945 (9'8") 2945 (9'8")
Ground pressure kg/cm2 (PSI) 0.50 (7.11) 0.50 (7.11) 0.43 (6.11) 0.32 (4.55)
DOZER EQUIPMENT
Type Inside mount Inside mount Inside mount Inside mount
Weight kg (lb) 2340 (5,160) 2500 (5,510) 2480 (5,470) 2630 (5,800)
(Includes hydraulic control unit)
Length mm (ft.in) 3275 (10'9") 3860 (12'8") 3275 (10'9") 3860 (12'8")
Height mm (ft.in) 1200 (3'11") 1160 (3'10") 1200 (3'11") 1160 (3'10")
D Max. lift above ground mm (ft.in) 915 (3') 915 (3') 1045 (3'5") 1020 (3'4")
E Max. drop below ground mm (ft.in) 515 (1'8") 515 (1'8") 550 (1'10") 575 (1'11")
F Max. tilting adjustment mm (ft.in) 510 (1'8") 600 (2') 515 (1'8") 600 (2')
1B-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
D
G.L
F
E
B A
Model
D68ESS-12*4
Item
OPERATING WEIGHT* kg (lb) 18,800 (41,500)
DOZER EQUIPMENT
Type Inside mount
Weight kg (lb) 2,360 (5,205)
(Includes hydraulic control unit)
Length mm (ft.in) 3276 (10'9")
Height mm (ft.in) 1200 (3'11")
D Max. lift above ground mm (ft.in) 1045 (3'5")
E Max. drop below ground mm (ft.in) 560 (1'10")
F Max. tilting adjustment mm (ft.in) 510 (1'9")
1B-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Model
D61EX-12 D65E-12 D65EX-15 D65EX-15 LT
Item
OPERATING WEIGHT* kg (lb) 15510 (34,190) 18500 (40,780) 19350 (42,600) 20090 (44,290)
BLADE CAPACITY LH2** m3 (yd3) 5.4 (7.1) 6.8 (8.9) 7.03 (9.19) 7.03 (9.19)
SAE 4.3 (5.6) 5.6 (7.3) 5.61 (7.34) 5.61 (7.34)
DIMENSION*
A Overall length mm (ft.in) 5050 (16'7") 5440 (17'10") 5440 (17'10") 5440 (17'10")
B Overall width mm (ft.in) 3175 (10'5") 3460 (11'4") 3460 (11'4") 3460 (11'4")
C Overall height mm (ft.in) 2945 (8'2") 2990 (9'10") 2990 (9'10") 2990 (9'10")
Ground pressure kg/cm2 (PSI) 0.50 (7.11) 0.68(9.67) 0.71 (10.1) 0.60 (8.53)
DOZER EQUIPMENT
Weight kg (lb) 2380 (5,270) 2880 (6,350) 3000 (7,890) 3000 (7,890)
(Includes hydraulic control unit)
Length mm (ft.in) 3175 (10'5") 3460 (11'4") 3460 (11'4") 3460 (11'4")
Height mm (ft.in) 1300 (4'3") 1425 (4'8") 1425 (4'8") 1425 (4'8")
D Max. lift above ground mm (ft.in) 965 (3'2") 1105 (3'8") 1105 (3'8") 1105 (3'8")
E Max. drop below ground mm (ft.in) 535 (1'9") 440 (1'5") 440 (1'5") 440 (1'5")
F Max. tilting adjustment mm (ft.in) 690 (2'3") 465 (1'6") 855 (2'10") 855 (2'10")
1B-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Model D275A-5***
D375A-5 D375A-5*** D475A-5
Item D275AX-5***
OPERATING WEIGHT* kg (lb) 45270 (99,800) 60340 (133,030) 61590 (135,780) 95280 (210,050)
45270 (99,800)
BLADE CAPACITY LH2** m3 (yd3) 16.5 (21.6) 24.0 (31.4) 24.0 (31.4) 38.1 (49.8)
SAE 13.7 (17.9) 18.5 (24.2) 18.5 (24.2) 27.2 (35.6)
DIMENSION*
A Overall length mm (ft.in) 6930 (22'9") 7635 (25'1") 7635 (25'1") 8700 (28'7")
B Overall width mm (ft.in) 4300 (14'1") 4695 (15'5") 4695 (15'5") 5265 (17'5")
C Overall height mm (ft.in) 3965 (13'0") 4035 (13'3") 4035 (13'3") 4240 (13'11")
Ground pressure kg/cm2 (PSI) 1.09 (15.50) 1.29 (18.34) 1.31 (18.63) 1.54 (21.90)
1.09 (15.50)
DOZER EQUIPMENT
Weight kg (lb) 7590 (16,730) 10540 (23,240) 11790 (25,990) 16500 (36,380)
(Includes hydraulic control unit)
Length mm (ft.in) 4300 (14'1") 4695 (15'5") 4695 (15'5") 5265 (17'5")
Height mm (ft.in) 1960 (6'5") 2265 (7'5") 2265 (7'5") 2690 (8'10")
D Max. lift above ground mm (ft.in) 1450 (4'9") 1660 (5'5") 1660 (5'5") 1620 (5'4")
E Max. drop below ground mm (ft.in) 640 (2'1") 715 (2'4") 715 (2'4") 1010 (3'4")
F Max. tilting adjustment mm (ft.in) 1140 (3'9") 1065 (3'6") 1165 (3'10") 770 (2'6")
Model
D475A-5***
Item
OPERATING WEIGHT* kg (lb) 95580 (210,720)
DOZER EQUIPMENT
Weight kg (lb) 16800 (37,040)
(Includes hydraulic control unit)
Length mm (ft.in) 5265 (17'5")
Height mm (ft.in) 2690 (8'10")
D Max. lift above ground mm (ft.in) 1620 (5'4")
E Max. drop below ground mm (ft.in) 1010 (3'4")
F Max. tilting adjustment mm (ft.in) 1145 (3'9")
* : Including dozer equipment in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
*** : Dual tiltdozer
1B-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
D
F G.L
E
B A
Model
D375A-5 D375A-5*** D475A-5 D475A-5***
Item
OPERATING WEIGHT* kg (lb) 61590 (135,780) 61970 (136,620) 97280 (214,460) 97580 (215,120)
BLADE CAPACITY LH2** m3 (yd3) 26.3 (34.4) 26.3 (34.4) 42.3 (55.3) 42.3 (55.3)
SAE 22.0 (28.8) 22.0 (28.8) 34.4 (45.0) 34.4 (45.0)
DIMENSION*
A Overall length mm (ft.in) 8000 (26'5") 8000 (26'5") 9200 (30'2") 9200 (30'2")
B Overall width mm (ft.in) 5140 (16'10") 5140 (16'10") 6205 (20'4") 6205 (20'4")
C Overall height mm (ft.in) 4035 (13'3") 4035 (13'3") 4240 (13'11") 4240 (13'11")
Ground pressure kg/cm2 (PSI) 1.31 (18.63) 1.32 (18.77) 1.57 (22.33) 1.57 (22.33)
DOZER EQUIPMENT
Weight kg (lb) 11790 (25,990) 12170 (26,830) 18500 (40,790) 18800 (41,450)
(Includes hydraulic control unit)
Length mm (ft.in) 5140 (16'10") 5140 (16'10") 6205 (20'4") 6205 (20'4")
Height mm (ft.in) 2265 (7'5") 2265 (7'5") 2610 (8'7") 2610 (8'7")
D Max. lift above ground mm (ft.in) 1660 (5'5") 1660 (5'5") 1620 (5'4") 1620 (5'4")
E Max. drop below ground mm (ft.in) 715 (2'4") 715 (2'4") 1010 (3'4") 1010 (3'4")
F Max. tilting adjustment mm (ft.in) 1165 (3'10") 1260 (4'2") 905 (3'0") 1350 (4'5")
* : Including dozer equipment in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
*** : Dual tiltdozer
1B-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
DOZER EQUIPMENT
Weight kg (lb) 23385 (51,550)
(Includes hydraulic control unit)
Length mm (ft.in) 6800 (22'4")
Height mm (ft.in) 2600 (8'6")
D Max. lift above ground mm (ft.in) 1850 (6'1")
E Max. drop below ground mm (ft.in) 900 (2'11")
F Max. tilting adjustment mm (ft.in) 1600 (5'3")
* : Including dozer equipment in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
C
D
F G.L
E
B A
FVBH0333
Super Dozer
Model
D475A-5 SD D575A-3 SD
Item
OPERATING WEIGHT* kg (lb) 106190 152410
(234,110) (336,000)
BLADE CAPACITY LH2** m3 (yd3) 69.0 (90.3)
SAE 45.0 (58.9) 60.0 (78.5)
DIMENSION*
A Overall length mm (ft.in) 10525 (34'6") 11720 (38'5")
B Overall width mm (ft.in) 6465 (21'3") 7400 (24'3")
C Overall height mm (ft.in) 4240 (13'11") 4495 (14'9")
Ground pressure kg/cm2 (PSI) 1.53 (21.8) 1.50 (21.33)
DOZER EQUIPMENT
Weight kg (lb) 21200 (46,740) 32430 (71,500)
(Includes hydraulic control unit)
Length mm (ft.in) 6465 (21'3") 7400 (24'3")
Height mm (ft.in) 3220 (10'7") 3250 (10'8")
D Max. lift above ground mm (ft.in) 1960 (6'5") 1750 (5'9")
E Max. drop below ground mm (ft.in) 860 (2'10") 805 (2'8")
F Max. tilting adjustment mm (ft.in) 900 (2'11") 1000 (3'3")
COUNTERWEIGHT kg (lb) 6400 (14,110) 5400 (11,900)
* : Including dozer equipment and counterweight in addition to bare tractor, excluding ROPS and cab.
** : L: Blade length H: Blade height
*** : Dual tiltdozer
1B-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
F E
B A
FVBH0200
Model
D155AX-5 D155A-5 D155A-2A
Item
OPERATING WEIGHT* kg (lb) 34830 (76,790) 33330 (73,480) 34250 (75,510)
BLADE CAPACITY LH2** m3 (yd3) 21.5 (28.1) 21.5 (28.1) 17.2 (22.5)
SAE
DIMENSION*
A Overall length mm (ft.in) 6900 (22'8") 6900 (22'8") 7020 (23')
B Overall width mm (ft.in) 5300 (17'5") 5300 (17'5") 5300 (17'5")
C Overall height mm (ft.in) 3395 (11'2") 3395 (11'2") 3725 (12'3")
Ground pressure kg/cm2 (PSI) 0.76 (10.8)*** 0.73 (10.5)*** 0.97 (13.79)
DOZER EQUIPMENT
Type Coal dozer with Coal dozer with Coal dozer with
power tilt power tilt power tilt
Weight kg (lb) 4930 (10,870) 4930 (10,870) 6380 (14,070)
(Includes hydraulic control unit)
Length mm (ft.in) 5300 (17'5") 5300 (17'5") 5300 (17'5")
Height mm (ft.in) 2125 (7'0") 2125 (7'0") 1800 (5'11")
D Max. lift above ground mm (ft.in) 1495 (4'11") 1495 (4'11") 1620 (5'4")
E Max. drop below ground mm (ft.in) 565 (1'0") 565 (1'10") 545 (1'9")
F Max. tilting adjustment mm (ft.in) 1270 (4'2") 1270 (4'2") 1270 (4'2")
1B-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
Production BULLDOZERS
The estimated production curves give maximum production before correction and are based on the following
conditions.
1. 100% efficiency
2. 0.05 min time fixed (for gear shifting)
3. Machine cuts for 15 m (50 ft), then drifts blade load.
4. Gear
JOB EFFICIENCY
• Good 0.83 (50 min out of an hour machine use)
• Average 0.75 (45 min out of an hour machine use)
• Rather poor 0.67 (40 min out of an hour machine use)
• Poor 0.58 (35 min out of an hour machine use)
1B-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
Production BULLDOZERS
Lyd3/h Lm3/h
3600 2800
D475A D575A
3400 2600
D375A
3200
2400
3000
2800 2200
2600 2000
D275A/AX
2400
1800
HOURLY PRODUCTION
2200
1600
2000
1800 1400
1600 1200
1400 D155AX-5
1000
1200 D155A-5
1000 800
D155A-2
800 600
600
400
400
200
200
0 0
0 15 30 45 60 75 90 105 120 135 150 165 180 195 m
0 100 200 300 400 500 600 ft
AVERAGE DOZING DISTANCE
FVBH0181
2600 2000
D275A/AX
2400
1800
HOURLY PRODUCTION
2200
1600
2000
1800 1400
1600 1200 D155A-2A
1400 D155AX-5
1000
1200 D155A-5
1000 800
800 600
600
400
400
200
200
0 0
0 15 30 45 60 75 90 105 120 135 150 165 180 195 m
0 100 200 300 400 500 600 ft
AVERAGE DOZING DISTANCE
FVBH0182
1B-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
Production BULLDOZERS
4400 3400
4200 3200
4000
3000
3800
3600 2800
3400 2600
3200
2400
HOURLY PRODUCTION
3000
2800 2200
2600 2000
2400
1800
2200
1600
2000
1800 1400
1600 1200
1400
1000
1200
1000 800
800 600
600
400
400
200
200
0 0
0 15 30 45 60 75 90 105 120 135 150 165 180 195 m
0 100 200 300 400 500 600 ft
AVERAGE DOZING DISTANCE
FVBH0183
1B-18
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 1C
RIPPERS
CONTENTS
Features .................................................................... 1C-2
Ripper specification:
Multi-shank ripper (rigid type) ............................ 1C-3
Multi-shank ripper (variable type) ...................... 1C-5
Giant ripper (variable type) ................................. 1C-6
Ripper selection ....................................................... 1C-7
Ripper point selection ............................................. 1C-8
Production .............................................................. 1C-11
1C-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features RIPPERS
Outstanding productivity
1. Superior ripping performance is achieved through a large operating weight, high engine output and a
conventional drive undercarriage.
2. Large maximum penetration depth provides high ripper production.
3. The unique linkage design enables the ripper point to draw an ideal locus during cylinder tilting for
effective excavation of embedded rocks.
In the KOMATSU linkage, the lift cylinder is mounted on the beam, causing the point to make an
ideal movement when the tilt cylinder is actuated.
Thus, the range of digging angles practically available is wider than the conventional type range,
giving excellent digging force.
Tilt cylinder
Lift cylinder
Beam
Arm
FVBH0302 FVBH0305
• This patented mechanism lets the point make an ideal • After penetrating the ground, the point makes longer
movement when the tilt cylinder is in action, which in turn downward movements, resulting in a narrow digging
gives rise to a large digging force over the entire digging angle range in which materials can be lifted or rolled out.
angle range.
Lifting
Distance Lifting
Range capable Distance Range capable
of lifting out of lifting out
material material
Rolling range FVBH0303 Rolling range FVBH0306
(Relationship between the digging angle and the digging force when the tilt cylinder is in action)
Lifting-out force(f)
Lifting-out force(f)
20 O 20
10 10
0 0
37.5 50 66 35 45 63
Penetration angle(degree) FVBH0304 Penetration angle(degree) FVBH0307
Minimum downtime
1. Large sectional area of the beam extends service life.
2. The forged ripper points are sharpened for excellent penetration and long service life.
Easy operation
1. Optional pin puller facilitates change in digging depth.
The optional pin puller mechanism functions to insert or remove the pin from its hole. This is
accomplished with a hydraulic cylinder and can be accomplished by an experienced operator, from within
the cab. This feature thus provides a time savings benefit.
Shank
Aligning
marks
Holder
1C-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Specifications RIPPERS
Multi-shank Ripper (Rigid type)
B
A
B
D
G.L
E C
F
Model
D31EX-21 D37EX-21 D39EX-21 D41E-6
Item
RIPPER EQUIPMENT:
Type Tool bar Tool bar Tool bar Parallelogram
Weight** kg (lb) 575 (1,270) 575 (1,270) 575 (1,270) 810 (1,790)
A Beam length mm (ft.in) 1530 (5'0") 1530 (5'0") 1530 (5'0") 1555 (5'1")
Shanks:
No. of shanks 5 5 5 3
Tooth point Replaceable Replaceable Replaceable Replaceable
B Pitch (3 shank) mm (ft.in) 700 (2'4") 700 (2'4") 700 (2'4") 700 (2'4")
Pitch (2 shank) mm (ft.in) 1400 (4'7")
Digging angle degree Fixed Fixed 55°
Fixed
Model D65E-12
D61EX-12 D85ESS-2A D85EX-15
Item D65EX-15
RIPPER EQUIPMENT:
Type Parallelogram Parallelogram Parallelogram Parallelogram
Weight** kg (lb) 1645 (3,630) 1680 (3,700) 1680 (3,700) 2500 (5,520)
A Beam length mm (ft.in) 2170 (7'1") 2170 (7'1") 2170 (7'1") 2227 (7'4")
Shanks:
No. of shanks 3 3 3 3
Tooth point Replaceable Replaceable Replaceable Replaceable
B Pitch (3 shank) mm (ft.in) 950 (3'1") 950 (3'1") 950 (3'1") 1000 (3'3")
Pitch (2 shank) mm (ft.in) 1900 (6'3") 1900 (6'3") 1900 (6'3") 2000 (6'7")
Digging angle degree 55°, 45° 55°, 45° 2-stage 54.5°
2-stage 2-stage adjustable
adjustable adjustable
Digging depth 3-stage 3-stage 3-stage 2-stage
adjustable adjustable adjustable adjustable
Max. digging depth mm (ft.in) 665 (2'2") 595 (1'11") 595 (1'11") 655 (2'2")
C Max. lift above ground mm (ft.in) 565 (1'10") 640 (2'1") 640 (2'1") 565 (1'10")
D Ripper point reach mm (ft.in) 1289 (4'3") 1300 (4'3") 1295 (4'3")
E Tail length mm (ft.in) 1788 (5'10") 1795 (5'11") 1790 (5'10") 2075 (6'10")
F
HYDRAULIC CONTROL UNIT* kg (lb) 35 (80) 70 (150) 70 (150)
1C-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Specifications RIPPERS
Multi-shank Ripper (Rigid type)
B
A
B
D
G.L
E C
F
Model
D155A-2A
Item
RIPPER EQUIPMENT:
Type Parallelogram
Weight** kg (lb) 4870 (10,740)
A Beam length mm (ft.in) 2420 (7'11")
Shanks:
No. of shanks 3
Tooth point Reversible
B Pitch (3 shank) mm (ft.in) 1120 (3'8")
Pitch (2 shank) mm (ft.in) 2240 (7'4")
Digging angle degree 45°
1C-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Specifications RIPPERS
Multi-shank Ripper (Variable type)
B
A
B
D
G.L
E C
F
Model
D475A-5
Item
RIPPER EQUIPMENT:
Type Variable
digging angle
type
Weight** kg (lb) 9720 (21,430)
A Beam length mm (ft.in) 3085 (10'1")
Shanks:
No. of shanks 3
Tooth point Replaceable
B Pitch (3 shank) mm (ft.in) 1385 (4'7")
Pitch (2 shank) mm (ft.in) 2770 (9'1")
Digging angle degree Std:45°
Stepless
adjustable
1C-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Specifications RIPPERS
Giant Ripper (Variable type)
B
G.L
C
A
Model D155A-5
D155A-2A D275A-5 D275AX-5
Item D155AX-5
RIPPER EQUIPMENT:
Type Variable Variable Variable Variable
digging angle digging angle digging angle digging angle
type type type type
Weight** kg (lb) 2760 (6,080) 4830 (10,650) 4600 (10,140) 3600 (7,940)
Shanks:
No. of shanks 1 1 1 1
Tooth point Reversible Replaceable Replaceable Replaceable
Digging angle degree Std:49° Std:45° Std:42.7°
Stepless Stepless Stepless Stepless
adjustable adjustable adjustable adjustable
Model
D375A-5 D475A-5 D575A-3
Item
RIPPER EQUIPMENT:
Type Variable Variable Variable
digging angle digging angle digging angle
type type type
Weight** kg (lb) 5470 (12,060) 7300 (16,090) 10530 (23,210)
Shanks:
No. of shanks 1 1 1
Tooth point Replaceable Replaceable Replaceable
Digging angle degree Std:45° Std:45° Std:45°
Stepless Stepless Stepless
adjustable adjustable adjustable
1C-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
L: Giant
: Multi-Shank Push plate
L FVBH0310 FVBH0311
M-3 Adaptable to hard or soft rock by increasing or G-3 Deep penetration and large distance from shank
decreasing the number of shanks. to rear of bulldozer make it possible to handle large
rocks.
G-4 Pin puller simplifies changing shank length.
1C-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Various types of ripper points are available, and the general standards for selection according to the
type of use are given below.
When combining of these categories, 4~7 types of points are available for each model.
If the point does not dig into the rock, but slips on the rock surface, the friction heat between the point and
rock causes an extreme rise in temperature of the point, thus reducing point hardness.
There is a close relationship between hardness and wear: The higher the hardness, the less the wear.
Also there is a close relationship between
increased temperature of the point and excellent Red
wear of the point (abnormal wear). Hardness and wear life
Yellow
retains its hardness better than the yellow point
Wear life
Has a wear life 1.5 ~ 2.0 times greater than the short point, but its strength is inferior to
Long
the short point because of its extra length.
Compared with the long point, it has superior strength, but has inferior wear life compare to
Short
the long point.
This has a self-sharpening shape, so it always retains its cutting edge, and provides a
long life on jobsites where there is soft rock and penetration ability is not required.
The rib provided only on the top surface wears gradually under the flow of the soil, and there
is no change in the penetration surface pressure.
Penetration surface pressure
10 Symmentric type
Symmentric type
Non symmentric type
10
Turn
Symmetric type
(can be turned) Necessary surface
5 pressure (hard rock)
0
Distance from tip (L) mm
1C-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
The table below gives a summary of the features of each type of point.
Strength,
Seismic Wear Abnormal
Length Color Shape resistance to Penetration Cost
velocity tolerance wear
impact
Symmetric
type
Yellow 4
Non
symmetric
type No
Short particular
Symmetric limit
type
Red 2
Non
symmetric
type
Non
Yellow symmetric (As a 3
type guideline)
Long
Non Max.
Red symmetric 1500m/sec 1
type
Key : Good, : Average, : Poor
Cost: 1 (Most expensive), 4 (Least expensive)
1C-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Step 1 Selection
Yes
Install standard point B Step 3 A
(Check for
Step 2 crack or
(Check wear) breakge)
B
Yes
Yes
Yes
(Over 70%) No
Does rock have Does impact
high quartz Install standard point B force causes C
contents? breakage?
*1[Whole point is worn evenly]
Excessive generation No
of heat at point (Less than 70%)
[Only tip of point is worn]
Does impact No
Install point D force causes D
breakage?
Yes
E
D275AX-5
D85EX-15
D155A-5
D155A-2
D275A-5
D375A-5
D475A-5
Selection Type of
Hardness Features Shape
rock
1C-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Production RIPPERS
Not all material can be ripped. Whether or not a rock Characteristics which determine the ease of
can be ripped can be determined by any of the rippability are summarized below.
following methods:
1) By the type of rock • Favorable rock for ripping
2) By an indoor rock test
Stratified
3) By a field rock test Weathered
4) By a digging test with the ripper in the field. Brittle, crystalline nature
High degree of laminations or thin layers.
Method 4) is most effective. If the user has no Fractured
experience in ripping, an actual ripping operation Faults or planes of weakness.
should be demonstrated for the user by an operator
experienced in ripping. Methods 1) and 3) are • Unfavorable rock for ripping
described below :
Fine-grained with a solid cementing agent.
Determination of rippability by type Moisture, which tends to solidify the rock surface layer.
of rock
Lacking planes of weakness
Massive and homogeneous
Rocks are classified into sedimentary (aqueous), Non-crystalline and not brittle
igneous, and metamorphic. The following general
rules apply:
Determination of rippability by in-
1) Sedimentary rocks such as sandstone, limestone,
and shale can be ripped easily. Sedimentary
the-field rock test.
rocks are usually found stratified in layers which Seismic wave velocity tests are used to estimate the
vary in thickness. The thinner the layers, the rippability of rock. In this test, an artificial earthquake
easier it is to rip them. is introduced and the travel speeds of seismic waves
through different kinds of sub-surface materials are
2) Igneous rocks such as granite, basalt, and
measured. Thus the degree of consolidation,
andesite are not found in distinct layers or
thickness of sub-surface layers, hardness, degree of
cleavage planes, and this makes them difficult to
fracturing, stratification, and weathering can be
rip.
determined .
3) Metamorphic rocks such as gneiss, schist, and
quartzite vary in rippability according to the
degree of stratification or cleavage. The chart below compares ripper performance to
seismic velocities. It should be used ONLY A
Rippability depends not only on the type of rock, but
ROUGH GUIDE, because ripper performance is
also on the degree of weathering or fracturing.
subject to many other conditions.
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
1C-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Production RIPPERS
The chart below compares ripper performance to seismic velocities. It should be used ONLY A ROUGH
GUIDE, because ripper performance is subject to many other conditions.
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
Seismic velocity 0 500 1000 1500 2000 2500 3000 3500 (m/s)
0 2 4 6 8 10 12 (X 1000ft/s)
FVBH0260
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
Seismic velocity 0 500 1000 1500 2000 2500 3000 3500 (m/s)
0 2 4 6 8 10 12 (X 1000ft/s)
FVBH0261
1C-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
Production RIPPERS
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
Seismic velocity 0 500 1000 1500 2000 2500 3000 3500 (m/s)
0 2 4 6 8 10 12 (X 1000ft/s)
FVBH0262
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
Seismic velocity 0 500 1000 1500 2000 2500 3000 3500 (m/s)
0 2 4 6 8 10 12 (X 1000ft/s)
FVBH0263
1C-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
Production RIPPERS
Operation conditions E
0.75 1000 D155AX
Good
(45 min out of an hour use) 1200
0.58
Average 800
(35 min out of an hour use)
0.50 D155A
Rather poor
(30 min out of an hour use) 800 600
0.40
Poor
(25 min out of an hour use)
400
400
200
0
500 1000 1500 2000 2500 3000 4000 (m/s)
2000 4000 6000 8000 10000 (ft/s)
SEISMIC WAVE VELOCITY
FVBH0184
Conditions
1) Ripping production only
2) Bulldozers with single shank rippers
3) 100% job efficiency
1C-14
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 1D
TOWING WINCHES
CONTENTS
Specifications ........................................................... 1D-2
1D-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
A
B
C
FVBH0201
Model
D65EX/PX-15 D68ESS-12 D70LE-8 D85ESS-2
Item
Type Wet type Wet type Dry type Wet type
Weight kg (lb) 1290 (2,840) 1570 (3,455) 1390 (3,060) 1290 (2,840)
DIMENSION
A: Ground to drum center mm (ft.in) 1201 (3'11") 1145 (3'9") 1188 (3'11") 1201 (3'11")
B: Ground to hitch center mm (ft.in) 650 (2'2") 610 (2') 612 (2'0") 650 (2'2")
C: Sprocket center to drum center mm (ft.in) 907 (3'0") 945 (3'1") 934 (3'1") 1066 (3'6")
Drum dimension:
Length mm (ft.in) 1005 (3'4") 975 (3'2") 1035 (3'5") 1005 (3'4")
Width mm (ft.in) 1070 (3'6") 996 (3'3") 1135 (3'9") 1070 (3'6")
Height mm (ft.in) 980 (3'3") 980 (3'3") 910 (3') 980 (3'3")
Drum diameter mm (ft.in) 254 (10") 254 (10") 290 (11.4") 254 (10")
Flange diameter mm (ft.in) 510 (1'8") 510 (1'8") 560 (1'10") 510 (1'8")
Drum width mm (ft.in) 320 (1'1") 320 (1'1") 335 (1'1") 320(1'1")
Cable:
Cable dia. × length mm × m 26 × 73 28.6 x 50 26 × 65 26 × 73
(in × ft) (1.02 × 240) (1.12 x 165) (1.02 × 213) (1.02 × 240)
Performance:
Line speed:
Bare drum m/min. F28 (92) F28 (92) F30 (98) F28 (92)
(FPM) R59 (194) R63 (207) R50 (164) R63 (207)
Full drum m/min. F48 (157) F48 (157) F30 (98) F48 (157)
(FPM) R102 (335) R110 (361) R50 (164) R110 (361)
Line pull:
Bare drum kg (lb) 31400 (69,220) 26910 (59,322) 26400 (58,200) 31400 (69,220)
Full drum kg (lb) 18200 (40,120) 15570 (34,323) 15600 (34,390) 18200 (40,120)
1D-2
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 1E
PIPELAYERS
CONTENTS
Features .................................................................... 1E-2
Specifications ........................................................... 1E-3
Lifting capacity ......................................................... 1E-4
1E-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features PIPELAYERS
Safe operation
• Komatsu pipelayers offer safety features to keep
operators working confidently.
• All machines are standardly equipped with an
automatic boom maximum stopper device.
• There is a free-fall setting on the hook control
lever for use during an emergency.
• Komatsu pipelayers have a closed-type winch
brake that prevents slips during operation in wet
weather.
• Because the hook wires are located away from
the operator, danger in the event of a wire cut is
minimized.
1E-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Specifications PIPELAYERS
Model
D85C-21 D155C-1 D355C-3
Item
OPERATING WEIGHT kg (lb) 30050 (66,250) 45800 (100,970) 57850 (127,540)
MAX. LlIFTING CAPACITY kg (lb/kN) 41000 70000 92000
(90,390/402) (154,320/686) (202,820/902)
FLYWHEEL HORSEPOWER HP (kW)/RPM 225 (168)/2000 320 (239) /2000 360 (269)/2000
DIMENSIONS:
Overall length mm (ft.in) 4805 (15'9") 5840 (19'2") 6030 (19'9")
Overall width* mm (ft.in) 3490 (11'5") 3760 (12'4") 4405 (14'5")
Overall height mm (ft.in) 3640 (11'11") 3845 (12'7") 3925 (12'11")
Track gauge mm (ft.in) 2250 (7'5") 2380 (7'10") 2550 (8'4")
Length of track on ground mm (ft.in) 2730 (8'11") 3620 (11'11") 3750 (12'4")
2
Ground contact area cm (sq.in) 33300 (5,160) 51400 (7,967) 64500 (10,000)
Ground pressure kg/cm2(PSI/kPa) 0.90 (12.8/88.3) 0.89 (12.66/87.3) 0.90 (12.8/88.3)
PIPELAYING EQUIPMENT:
Hook speeds:(bare drum) m/min (FPM)
Raise 1st 9.6 (31.5) 6.0 (19.7) 5.5 (18.0)
2nd 21.7 (71.2) 13.8 (45.3) 12.7 (41.7)
Lower 1st 9.3 (30.5) 4.8 (15.7) 4.5 (14.8)
2nd 21.1 (69.2) 11.1 (36.4) 10.2 (33.5)
Boom: Length mm (ft.in) 5500 (18'1") 6200 (20'4") 7300 (23'11")
Winch: Type H.C** H.C** H.C**
ENGINE: KOMATSU KOMATSU KOMATSU
Model S6D125 SA6D140 SA6D140
No.of cylinders- mm 6-125 × 150 6-140 × 165 6-140 × 165
bore × stroke (in) (4.92 × 5.91) (5.51 × 6.50) (5.51 × 6.50)
Piston displacement Itr (cu.in) 11.04 (674) 15.24 (930) 15.24 (930)
PERFORMANCE:
Travel speeds km/h (MPH)
Forward/Reverse 1st 3.5 (2.2)/4.7 (2.9) 3.6 (2.2)/4.4 (2.7) 3.3 (2.1)/3.9 (2.4)
2nd 6.5 (4.0)/8.3 (5.2) 6.6 (4.1)/7.8 (4.8) 5.9 (3.7)/7.0 (4.3)
3rd 10.7(6.6)/13.3(8.3) 11.2(7.0)/12.4(7.7) 9.8(6.1)/11.0(6.8)
UNDERCARRIAGE:
No. of rollers (Carrier/track) 2/6 2/8 2/8
Shoe width
Standard mm (in) 610 (24.0) 710 (28.0") 860 (34.0)
Optional mm (in) 660 (26.0) 760 (30.0") 960 (38.0)
710 (28.0) 1010 (40.0)
* : Counterweight retracted, excluding boom
** : Hydraulically-controlled double-drum, reversible
D155C-1
3765 (12'4")
2070 (6'9")
1800
6780 (22'3")
(5'11")
3845 (12'7")
3770 (12'4")
3020 (9'11")
2845 (9'4")
G.L
(1'6")
460
3090 (10'2")
1E-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
D85C-21
Hook height
LIFTING CAPACITY
7.3 m Boom
HOOK HEIGHT
Working radius
6.2 m Boom
warking radius
(ANSI B30.14)
FVBH0026
BOOM OVERHANG
D155C-1
Boom overhang
HOOK HEIGHT
10
85 0%
%
6.2 m boom
warking radius
BOOM OVERHANG
FVBH0046
D355C-3
3
Boom overhang
HOOK HEIGHT
85 1
% 00%
7.3 m boom
warking radius
BOOM OVERHANG
FVBH0047
1E-4
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 1F
TRIMMING DOZERS
CONTENTS
Trimming operation in vessel ..................................1F-2
Design features .........................................................1F-3
Standard equipment .................................................1F-5
Track shoe selection .................................................1F-6
Specifications ............................................................1F-7
1F-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
1F-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
3
4
d c 2
2
5
1F-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
The trimming dozers destined for in-vessel cargo work are selected so as that other cargo handling
unloaders and derricks may function with good efficiency.
When selection is made on the models of trimming dozer, the structure of holds (hatch size, existence of twin
deck, frame conditions, etc.), capacity of unloader (lifting capacity and cargo volume),and cargo material to
be handled must be taken into consideration.
1F-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Standard Equipment
D85A-21
Air cleaner inner element, no-woven cloth made
Air cleaner inner element, urethane made
Alternator, corrosion proof type
Backup buzzer
Backup lamp, red color
Electric terminals, silicon compound coated
Engine side covers, perforated
Engine under guard, hinged type
Exhaust pipe, short
Fan, high speed
Front lights, additional
Fuel tank, large capacity
Hydraulic cylinder rod, thick chrome plated
Intake manifold, cast iron made
Oil pan, dual-bottom
Oil pan, stainless steel made
Radiator core protective grid
Radiator mask, hinged type
Radiator, corrosion proof type
Rear protector
Recoil spring, sealed type
Shoe, holed single grouser
Shoe, holed triple grouser
Starting motor, corrosion proof type
Tachometer with mechanical drive service meter
Track adjusting cylinders, thick chrome plated
Transmission oil cooler, tiltable
Wear resistant pulley
1F-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
FVBH0241
SINGLE GROUSER SHOE HOLED SINGLE GROUSER SHOE HOLED TRIPLE GROUSER SHOE SWAMP SHOE
A B C D
0.5 kg/cm2
Salt (7.1 PSI) ( ) ( ) ( ) ( )
D65E•EX-12 D85A-21
Shoe width A B C A B C
300 mm (11.8")
340 mm (13.4")
400 mm (15.7")
460 mm (18.1")
510 mm (20.0")
560 mm (22.0")
600 mm (23.6")
Ore 0.8 kg/cm2
(11.4 PSI)
0.8 kg/cm2
Coal (11.4 PSI)
Wooden 0.5 kg/cm2
chips (7.1 PSI)
Material
0.5 kg/cm2
Salt (7.1 PSI) ( ) ( )
0.5 kg/cm2
Sugar (7.1 PSI)
Grain 0.3 kg/cm2
(4.3 PSI)
0.3 kg/cm2
Fertilizer (4.3 PSI)
Note 1 : : Currently available shoes which can be used. ( means standard shoes.)
Note 2 : ( ) : Ground pressures are greater than the target values but have been used so far.
1F-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
I H
C
E
G.L
G D
F
B
Model
D31E-20 D31P-20 D41A-3 D53A-17
Item
OPERATING WEIGHT* kg (lb) 7000 (15,430) 7660 (16,890) 10540 (23,240) 13460 (29,670)
FLYWHEEL HORSEPOWER HP (kW)/RPM 70 (52)/2350 70 (52)/2350 92 (68)/2350 124 (93)/1900
PERFORMANCE:
Travel speed
Forward 1st 2.2 (1.4) 2.2 (1.4) 2.4 (1.5) 3.2 (2.0)
2nd 3.9 (2.4) 3.9 (2.4) 4.4 (2.7) 5.9 (3.7)
km/h (MPH)
3rd 6.5 (4.0) 6.5 (4.0) 7.6 (4.7) 9.8 (6.1)
Reverse 1st 2.4 (1.5) 2.4 (1.5) 3.0 (1.9) 3.9 (2.4)
2nd 4.3 (2.7) 4.3 (2.7) 5.5 (3.4) 7.1 (4.4)
3rd 7.1 (4.4) 7.1 (4.4) 9.4 (5.8) 11.9 (7.4)
DIMENSION*
A Overall length mm (ft.in) 4510 (14'10") 4690 (15'5") 5120 (16'10") 5510 (18'1")
B Overall width mm (ft.in) 2480 (8'2") 2780 (9'1") 2620 (8'7") 2890 (9'6")
C Overall height mm (ft.in) 1955 (6'5") 2045 (6'9") 2005 (6'7") 2365 (7'9")
D Length of track on ground mm (ft.in) 1880 (6'2") 2185 (7'2") 2060 (6'9") 2365 (7'9")
Ground pressure kg/cm2 (P.S.I) 0.47 (6.68) 0.29 (4.12) 0.64 (9.10) 0.62 (8.82)
DOZER EQUIPMENT
Weight (includes hydraulic control unit) kg (lb) 1380 (3,040) 1280 (2820) 1430 (3,150) 1800 (3,970)
Length mm (ft.in) 2480 (8'2") 2780 (9'1") 2620 (8'7") 2890 (9'6")
Height mm (ft.in) 750 (2'6") 750 (2'6") 850 (2'9") 930 (3'1")
Max. lift above ground mm (ft.in) 1480 (4'10") 1630 (5'4") 1435 (4'8") 1690 (5'7")
E Max. drop below ground mm (ft.in) 710 (2'4") 650 (2'2") 670 (9'6") 730 (2'5")
F Breast dimension mm (ft.in) 1200 (3'11") 1375 (4'6") 1540 (5'1") 1785 (5'10")
G Max. pitch adjustment
H Forward degree 38 37 38 50
I Reverse degree 24 26 25 25
Model
D65E-12 D65EX-12 D85A-21
Item
OPERATING WEIGHT* kg (lb) 19950 (43,980)** 20120 (44,360) 24500 (54,010)
FLYWHEEL HORSEPOWER HP (kW)/RPM 180 (135)/1950 180 (135)/1950 225 (168)/2000
PERFORMANCE:
Travel speed
Forward 1st 3.9 (2.4) 3.9 (2.4) 3.5 (2.2)
2nd 6.8 (4.2) 6.8 (4.2) 6.5 (4.0)
km/h (MPH)
3rd 10.6 (6.6) 10.6 (6.6) 10.7 (6.6)
Reverse 1st 5.0 (3.1) 5.0 (3.1) 4.7 (2.9)
2nd 8.6 (5.3) 8.6 (5.3) 8.3 (5.2)
3rd 13.4 (8.3) 13.4 (8.3) 13.3 (8.3)
DIMENSION*
A Overall length mm (ft.in) 6475 (21'3") 6475 (21'3") 6420 (21'1")
B Overall width mm (ft.in) 3210 (10'6") 3210 (10'6") 3410 (11'2")
C Overall height mm (ft.in) 2990 (9'10")*** 2990 (9'10")*** 3090 (10'2")
D Length of track on ground mm (ft.in) 2675 (8'9") 2675 (8'9") 2730 (8'11")
Ground pressure kg/cm2 (P.S.I) 0.73 (10.38) 0.74 (10.52) 0.80 (11.38)
DOZER EQUIPMENT
Weight (includes hydraulic control unit) kg (lb) 4330 (9,550) 4330 (9,550) 4440 (9,790)
Length mm (ft.in) 3210 (10'6") 3210 (10'6") 3410 (11'2")
Height mm (ft.in) 1000 (3'3") 1000 (3'3") 1185 (3'11")
Max. lift above ground mm (ft.in) 1610 (5'3") 1610 (5'3") 1730 (5'8")
E Max. drop below ground mm (ft.in) 685 (2'3") 685 (2'3") 740 (2'5")
F Breast dimension mm (ft.in) 1610 (5'3") 1610 (5'3") 1580 (5'2")
G Max. pitch adjustment
H Forward degree 29 29 27
I Reverse degree 22 22 24
* : Including dozer equipment in addition to bare tractor
** : Including cab and air conditioner
*** : To top of cab
1F-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
MEMO
CONTENTS
SECTION 2
INDEX
SECTION 2A
EXCAVATORS (BACKHOE)
CONTENTS
Features .................................................................... 2A-2
Series selection ...................................................... 2A-11
Specifications ......................................................... 2A-12
Dimensions ............................................................. 2A-27
Working ranges and Digging forces .................... 2A-37
Component dimensions and weights .................. 2A-45
Shoe selection ........................................................ 2A-60
Shoe application .................................................... 2A-61
Ground pressure .................................................... 2A-64
Bucket capacity definition ..................................... 2A-71
Bucket selection .................................................... 2A-72
Bucket and arm combinations .............................. 2A-74
Teeth features and Teeth selection ...................... 2A-84
Teeth selection ....................................................... 2A-85
Model selection ...................................................... 2A-91
Production ............................................................ 2A-100
2A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
2A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
Easy maintenance
• Hydraulic oil and filter/engine oil and
filter replacement interval extended
Oil and filter change interval
Model
Dash-7 Avance series
Item
450 (17.7")
2A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
Internet
Personal
computer terminal
WebCARE Server (for downloading
data)
Komatsu
distributors
Recommendation
• An appropriate recommendation can be made by viewing these data over the Internet.
• Proper driving methods
• Formulation of maintenance plans in advance that suit the customer's production schedule.
Customer's Benefit
• Sudden break down can be prevented through utilization of data trend (change over time).
• Ascertaining the facts and searching for the cause of the breakdown are simplified, thus enabling
problems to be resolved quickly.
• Down time can be shortened by the systematic use of Reman components.
• Machine life can be extended significantly by proper operation and proper maintenance.
2A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
2A-5
02A.fm Page 6 Tuesday, March 23, 2004 10:00 AM
Features EXCAVATORS
(BACKHOE)
• Heavy lift mode
(PC1800)
Lifting capacity is increased by approximately
10%.
visibility
• Pleasant operation with good
atmosphere inside cab
1) Adjustable wrist control lever (2)
2) Steplessly-adjustable monitor (PC120-PC400)
(1) FVBH0039
PC120-PC1250
• Multi-layer viscous damping mount
(PC200-PC400)
Operator fatigue has been reduced.
Paper filter of
density grandient type
FVBH0024
2A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
2A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
HD-Series
Komatsu HD-series features heavy
duty undercarriage for tough logging
operations
The HD-series-6 enjoys greater mobility and
dependability in wooded areas, scrap yards, and
other locations where rough terrain demands high
performance.
• Undercarriage designed for greater
durability
One Class Larger Undercarriage
(PC300HD)
All the components of the PC300HD-6
undercarriage are made for the one-class larger
PC400-6.
• 10 Track Rollers (Per Side) (PC400HD)
The number of track rollers has been increased
from 8 to 10, and the track roller mounting pitch
has been reduced compared to the PC400LC-6.
• Full Length Track Roller Guard
The full-length track roller guard covers the entire
length of the track frame.
This prevents stones from getting caught in the
track rollers and causing derailment.
• Recoil Spring Installed at a Higher Load
(PC400HD)
The pre-stressed load on the recoil springs is
16% greater than in the PC400LC-6, thus
increasing dependability on rough ground and
steep slopes, where tracks often slip, derail, and
suffer extensive damage.
• Long track and wide track gauge offer
excellent stability
The HD-series track frame accommodates a long
track and a wide track gauge so as to offer
excellent stability.
The PC300HD/400HD has more lifting capacity
than the PC300LC/400LC.
• Variable track gauge facilitates transport
The HD-series has a variable track gauge, so the
overall width in transit is narrower.
This means that the excavator can pass through
small tunnels and over narrow bridges in
mountain areas. (PC400HD)
2A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
2A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
Heavy-duty shovel undercarriage design
• Komatsu Mining Germany track system with oscillating shoes for optimum response to rugged mining
ground conditions
• Lifetime lubricated rollers
• Automatic track tensioning system
• Track shoes in high quality casting steel and engineered by finite element method
• Precision hard facing of contact surfaces for long term performance
• Different width of shoes available for best performance in softer mining ground conditions
Attachments
• Backhoe attachment available for all mining applications
• Closed box design combining steel plates and castings, engineered by finite element method for full
lifetime
• Wide selection of buckets and customized options
• Bucket wear package ranges to meet all mining conditions
• Attachment pin sealing arrangement for reduced bearing wear-parts costs
Service
• Hydraulically assisted ladder for ease and convenience access
• Upper structure walkway allows safe access to all service points
• Walk in machinery house provides all weather protection for service attention
• Automatic central lubrication system for attachment and main swing bearing
• Swing down service arm for fast, ground level refilling and evacuation and the minimizing of leakages
during service
• Complete machine delivered in pre-tested modules for fast erection on job side
2A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Features EXCAVATORS
(BACKHOE)
Series Selection
The AVANCE line-up is expanded, with different excavator series for different jobs.
You can choose the right machines for your work, factory-equipped for your operation.
• "Dash-7" Series, AVANCE "Standard" Series
Flexible, efficient excavators for a wider range of work
• AVANCE "HD" Series
"Heavy-duty" excavators with reinforced undercarriages for logging and scrap handling
• AVANCE "EXCEL and Custom" Series
Simple, basic excavators for easy operation and maintenance
• AVANCE "US" Series
Excavators with short tail swing profile for work on road ways,urban areas and logging road way
2A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC01-1 PC09-1 PC12R-8 PC15MRX-1
Item
Source Japan Japan Italy Japan
OPERATING WEIGHT* kg (lb) 380 (840) 890 (1,960) 1475 (3,250) 1805 (3,980)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 3.5 (2.6)/3000 8.4 (6.2)/2800 14.3 (10.6)/2450 15.0 (11.2)/2600
BUCKET CAPACITY RANGE 0.008 0.017 ~ 0.025 0.03 ~ 0.06 0.022 ~ 0.044
(SAE) m 3 (cu.yd) (0.01) (0.022) (0.033) (0.04) (0.078) (0.029) (0.058)
PERFORMANCE:
Swing speed RPM 7.0 8.3 9 8.3
Max travel speed km/h (MPH) 1.4 (0.9) Hi 3.0 (1.9) 2 (1.2) Hi 4.3 (2.7)
Lo 1.5 (0.9) Lo 2.3 (1.4)
DIMENSIONS: See the page of
dimensions.
ENGINE: HONDA KOMATSU KOMATSU KOMATSU
Model GX160KI 2D68E 3D68E 3D68E
No. of cylinders- mm 1-68 × 45 2-68 x 72 3-68 × 72 3-68 × 72
bore × stroke (in) (2.67 × 1.77) (2.68 × 2.83) (2.68 × 2.83) (2.68 × 2.83)
Piston displacement ltr. (cu.in) 0.163 (9.9) 0.522 (31.9) 0.784 (47.8) 0.784 (47.8)
HYDRAULIC SYSTEM: 1 × Variable
Hydraulic pump Gear pumps Gear pumps Gear pumps Piston+Gear pump
Max. oil flow ltr. (U.S.Gal)/min. 10 (2.6) 22 (5.8) 47.5 (12.6)
Max. oil pressure kg/cm2 (PSI) 150 (2130) 160 (2275) 220 (3130)
Track shoe width/ mm (in)/ 130 (5)/ 180 (7)/ 230 (9)/ 230 (9)/
ground pressure kg/cm2 (PSI) 0.17 (2.4) 0.28 (4.0) 0.29 (4.1)
CAPACITY (Refilled):
Fuel tank 4.5 (1.2) 11 (2.9) 20 (5.3) 19 (5.0)
Hydraulic oil tank ltr. (U.S.Gal) 4.8 (1.3) 12 (3.2) 23 (6.1) 14 (3.7)
MACHINE SPEC:
Boom mm (ft.in) 920 (3') 1760 (5'9")
Arm mm (ft.in) 480 (1'7") 684 (2'3") 880 (2'11") 965 (3'2")
Bucket (SAE) m 3 (cu.yd) 0.008 (0.01) 0.022 (0.029) 0.04 (0.05) 0.044 (0.058)
Upper attachment Canopy Canopy
Model
PC15R-8 PC20MRX-1 PC20R-8 PC27MRX**
Item
Source Italy Japan Italy Japan
OPERATING WEIGHT* kg (lb) 1575 (3,470) 2190 (4,830) 2535 (5,580) 2995 (6,605)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 15.3 (11.4)/2600 18.7 (14)/2600 23.3 (17.4)/2600 25.6 (19.1)/2600
BUCKET CAPACITY RANGE 0.03 ~ 0.06 0.033 ~ 0.08 0.035 ~ 0.085 0.042 ~ 0.09
(SAE) m 3 (cu.yd) (0.04) (0.078) (0.043) (0.10) (0.046) (0.11) (0.055) (0.12)
PERFORMANCE:
Swing speed RPM 10.4 9.3 9 9.2
Max travel speed km/h (MPH) Hi 4.2 (2.6) Hi 4.8 (3.0) Hi 4.3 (2.67) Hi 4.8 (3.0)
Lo 2.2 (1.4) Lo 2.3 (1.4) Lo 2.2 (1.36) Lo 2.4 (1.5)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model 3D68E 3D74E 3D78AE 3D82AE
No. of cylinders- mm 3-68 × 72 3-74 × 78 3-78 × 84 3-82 x 84
bore × stroke (in) (2.68 × 2.83) (2.91 × 3.07) (3.07 × 3.31) (3.23 x 3.31)
Piston displacement ltr. (cu.in) 0.784 (47.8) 1.006(61.4) 1.204 (73.4) 1.33 (81.2)
HYDRAULIC SYSTEM: 1 × Variable 1 × Variable 1 x Variable
Hydraulic pump Gear pumps Piston+Gear pump Piston+Gear pump Piston+Gear pump
Max. oil flow ltr. (U.S. Gal)/min. 59.8 (15.8) 71.3 (18.8)
Max. oil pressure kg/cm2 (PSI) 210 (2990) 220 (3130)
Track shoe width/ mm (in)/ 230 (9)/ 250 (10)/ 250 (10)/ 300 (12)/
ground pressure kg/cm2 (PSI) 0.27 (3.8) 0.34 (4.8)
CAPACITY (Refilled):
Fuel tank 20 (5.3) 25 (6.6) 35 (9.2) 37 (9.8)
Hydraulic oil tank ltr. (U.S. Gal) 23 (6.1) 21 (5.5) 29 (7.7) 28.5 (7.5)
MACHINE SPEC:
Boom mm (ft.in) 1809 (5'11'') 2120 (6'11")
Arm mm (ft.in) 965 (3'2") 930 (3'1'') 1070 (3'6") 1110 (3'8")
Bucket (SAE) m 3 (cu.yd) 0.04 (0.05) 0.066 (0.86) 0.07 (0.09) 0.08 (0.105)
Upper attachment Canopy Canopy Cab TOPS Canopy
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
2A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC27R-8 PC30MR-2 PC35R-8 PC35MR-2
Item
Source Italy Japan Italy Japan
OPERATING WEIGHT* kg (lb) 3065 (6,750) 3180 (7,010) 3670 (8,090) 3740 (8,245)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 26 (19.4)/2600 27.6 (20.6)/2500 28.2 (21)/2500 29.1 (21.7)/2400
BUCKET CAPACITY RANGE 0.045 ~ 0.105 0.035 ~ 0.11 0.5 ~ 0.13 0.055 ~ 0.13
(SAE) m 3 (cu.yd) (0.06) (0.14) (0.045) (0.14) (0.07) (0.17) (0.07) (0.17)
PERFORMANCE:
Swing speed RPM 9 9.3 9 9
Max travel speed km/h (MPH) Hi 4.4 (2.7) Hi 4.6 (2.9) Hi 4.6 (2.9) Hi 4.6 (2.9)
Lo 2.2 (1.36) Lo 2.6 (1.6) Lo 2.8 (1.7) Lo 2.8 (1.7)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model 3D82AE 3D84E 3D84E 3D88E
No. of cylinders- mm 3-82 × 84 3-84 × 90 3-84 × 90 3-88 x 90
bore × stroke (in) (3.23 × 3.31) (3.31 × 3.54) (3.31 × 3.54) (3.46 x 3.54)
Piston displacement ltr. (cu.in) 1.33 (81.2) 1.496 (91.3) 1.496 (91.3) 1.642 (100)
HYDRAULIC SYSTEM: 1 × Variable 1 × Variable 1 × Variable 2 x Variable
Hydraulic pump Piston+Gear pump Piston+Gear pump Piston+Gear pump Piston+Gear pump
Max. oil flow ltr. (U.S. Gal)/min. 93.3 (24.6) 92 (24.3)
Max. oil pressure 2
kg/cm (PSI) 265 (3770) 265 (3770)
Track shoe width/ mm (in)/ 300 (12)/ 300 (12)/ 300 (12)/ 300 (12)/
ground pressure kg/cm2 (PSI) 0.30 (4.3) 0.34 (4.9) 0.35 (5.0)
CAPACITY (Refilled):
Fuel tank 35 (9.2) 44 (11.6) 51.5 (13.6) 44 (11.6)
Hydraulic oil tank ltr. (U.S. Gal) 29 (7.7) 20 (5.3) 33 (8.7) 33 (8.7)
MACHINE SPEC:
Boom mm (ft.in) 2350 (7'9") 2560 (8'5")
Arm mm (ft.in) 1200 (3'11") 1260 (4'1") 1350 (4'5") 1350 (4'5")
Bucket (SAE) m 3 (cu.yd) 0.075 (0.10) 0.09 (0.12) 0.095 (0.12) 0.11 (0.14)
Upper attachment Cab Rops Canopy Cab ROPS Canopy
Model
PC40MR-2 PC45R-8 PC50MR-2
Item
Source Japan Italy Japan
OPERATING WEIGHT* kg (lb) 4790 (10,560) 4860 (10,710) 5040 (11,110)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 39.4 (29.4)/2500 38.8 (28.9)/2500 39.4 (29.4)/2350
BUCKET CAPACITY RANGE 0.055 ~ 0.16 0.07 ~ 0.175 0.055 ~ 0.16
(SAE) m 3 (cu.yd) (0.07) (0.21) (0.09) (0.22) (0.07) (0.21)
PERFORMANCE:
Swing speed RPM 9 9 9
Max travel speed km/h (MPH) Hi 4.6 (2.9) Hi 4.6 (2.9) Hi 4.6 (2.9)
Lo 2.8 (1.7) Lo 2.8 (1.7) Lo 2.8 (1.7)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU
Model 4D88E 4D84E 4D88E
No. of cylinders- mm 4-88 × 90 4-84 × 90 4-88 × 90
bore × stroke (in) (3.46 × 3.54) (3.31 × 3.54) (3.46 × 3.54)
Piston displacement ltr. (cu.in) 2.189 (134) 1.995 (122) 2.189 (134)
HYDRAULIC SYSTEM: 2 × Variable 1 × Variable 2 × Variable
Hydraulic pump Piston+Gear pump Piston+Gear pump Piston+Gear pump
Max. oil flow ltr. (U.S. Gal)/min. 134 (35.4) 129.5 (34) 134 (35.4)
Max. oil pressure 2
kg/cm (PSI) 265 (3770) 255 (3630) 265 (3770)
Track shoe width/ mm (in)/ 400 (16)/ 400 (16)/ 400 (16)/
ground pressure kg/cm2 (PSI) 0.28 (4.0) 0.29 (4.1)
CAPACITY (Refilled):
Fuel tank 65 (17.2) 51.5 (13.6) 65 (17.2)
Hydraulic oil tank ltr. (U.S. Gal) 55 (14.5) 33 (8.7) 55 (14.5)
MACHINE SPEC:
Boom mm (ft.in) 2740 (9'0") 2900 (9'6")
Arm mm (ft.in) 1440 (4'9") 1480 (4'10") 1640 (5'5")
Bucket (SAE) m 3 (cu.yd) 0.14 (0.18) 0.15 (0.20) 0.16 (0.21)
Upper attachment ROPS Canopy Cab ROPS Canopy
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** For USA
2A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC75R-2 PC78US-6 PC78MR-6 PC95R-2
Item
Source Italy Japan Japan Italy
OPERATING WEIGHT* kg (lb) 7400 (16,310) 6850 (15,100) 8270 (18,230) 8800 (19,400)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 68 (50)/2300 54 (40.5)/1850 54 (40.5)/1850 82.5 (61.5)/2200
BUCKET CAPACITY RANGE 0.086 ~ 0.265 0.09 ~ 0.34 0.09 ~ 0.34 0.086 ~ 0.34
(SAE) m 3 (cu.yd) (0.11) (0.35) (0.12) (0.45) (0.12) (0.45) (0.11) (0.44)
PERFORMANCE:
9.0
Swing speed RPM 10.2 10.0 10.0
Hi 5.0 (3.1)
Max travel speed km/h (MPH) Hi 5.1 (3.2) Hi 4.5 (2.8) Hi 4.2 (2.6)
Lo 3.1 (1.9) Lo 3.0 (1.9) Lo 2.8 (1.7)
Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model 4D98E S4D95LE S4D95LE 4D106
No. of cylinders- mm 4-98 × 110 4-95 × 115 4-95 x 115 4-106 × 125
bore × stroke (in) (3.86 × 4.33) (3.74 × 4.53) (3.74 x 4.53) (4.17 × 4.92)
Piston displacement ltr. (cu.in) 3.318 (202) 3.26 (199) 3.26 (199) 4.412 (269)
HYDRAULIC SYSTEM: 1 × Variable 2 × Variable 2 x Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
ltr. (U.S. Gal)/
Max. oil flow 227 (60) 160 (42.2) 160 (42.2) 242 (64)
min.
Max. oil pressure 270 (3840) 270 (3840) 270 (2840) 280 (3980)
kg/cm2 (PSI)
Track shoe width/ mm (in)/ 450 (18)/ 450 (18)/ 450 (18)/ 450 (18)/
ground pressure kg/cm2 (PSI) 0.34 (4.8) 0.33 (4.7) 0.38 (5.4) 0.38 (5.4)
CAPACITY (Refilled):
Fuel tank 100 (26.4) 125 (33) 125 (33)
Hydraulic oil tank ltr. (U.S. Gal) 70 (18.5) 56 (14.8) 64 (16.9)
MACHINE SPEC:
Boom mm (ft.in) 3000 (9'10") 3710 (12'2") 3400 (11'2") 2950 (9'7")
Arm mm (ft.in) 1700 (5'7") 1650 (5'5") 1650 (5'5") 1850 (6')
Bucket (SAE) m 3 (cu.yd) 0.232 (0.30) 0.28 (0.37) 0.28 (0.37) 0.298 (0.39)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
2A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC120-6 PC120-6*** PC120LC-6*** PC138US-2
Item
Source Japan Japan Japan Japan
OPERATING WEIGHT* kg (lb) 12030 (26,520) 12220 (26,940) 12600 (27,780) 13480 (29,720)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 86 (64)/2200 86 (64)/2200 86 (64)/2200 88.9 (66.2)/2200
BUCKET CAPACITY RANGE 0.18 ~ 0.60 0.35 ~ 0.70 0.18 ~ 0.60 0.18 ~ 0.60
(SAE) m 3 (cu.yd) (0.24) (0.78) (0.46) (0.92) (0.24) (0.78) (0.24) (0.78)
PERFORMANCE:
Swing speed RPM 11.0 11.0 11.0 11.0
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.0 (3.1) Hi 5.0 (3.1) Hi 5.1 (3.2)
Mi 3.6 (2.2) Mi 3.3 (2.1) Mi 3.3 (2.1)
Lo 2.7 (1.7) Lo 2.5 (1.6) Lo 2.5 (1.6) Lo 2.9 (1.8)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model S4D102E S4D102E S4D102E SAA4D95LE
No. of cylinders- mm 4-102 × 120 4-102 × 120 4-102 × 120 4-95 × 115
bore × stroke (in) (4.05 × 4.72) (4.05 × 4.72) (4.02 × 4.72) (3.74 × 4.53)
Piston displacement ltr. (cu.in) 3.92 (239) 3.92 (239) 3.92 (239) 3.26 (199)
HYDRAULIC SYSTEM: 1 × Variable 1 × Variable 1 × Variable 1 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 226 (60) 226 (60) 226 (60) 226 (60)
Max. oil pressure kg/cm2 (PSI) 355 (5050) 355 (5050) 355 (5050) 355 (5050)**
Track shoe width/ mm (in)/ 500 (20)/ 600 (24)/ 600 (24)/ 500 (20)/
ground pressure kg/cm2 (PSI) 0.40 (5.7) 0.34 (4.8) 0.31 (4.4) 0.43 (6.1)
CAPACITY (Refilled):
Fuel tank 230 (60.8) 240 (63.4) 240 (63.4) 200 (52.8)
Hydraulic oil tank ltr. (U.S. Gal) 100 (26.4) 100 (26.4) 100 (26.4) 69 (18.2)
MACHINE SPEC:
Boom mm (ft.in) 4600 (15'1") 4600 (15'1") 4600 (15'1") 4600 (15'1")
Arm mm (ft.in) 2500 (8'2") 2500 (8'2") 2500 (8'2") 2500 (8'2")
Bucket (SAE) m 3 (cu.yd) 0.50 (0.65) 0.50 (0.65) 0.50 (0.65) 0.50 (0.65)
Model PC130-6
PC138USLC-2*5 PC130-6 PC160LC-7
Item MIGHTY
Source Japan Japan UK Japan
OPERATING WEIGHT* kg (lb) 14050 (30,980) 12350 (27,230) 13050 (28,770) 16400 (36,160)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 88.9 (66.2)/2200 86 (64)/2200 86 (64)/2200 111 (82.4)/2200
BUCKET CAPACITY RANGE 0.35 ~ 0.70 0.50 0.24 ~ 0.68 0.60 ~ 0.70
(SAE) m 3 (cu.yd) (0.46) (0.92) (0.65) (0.31) (0.89) (0.78) (0.92)
PERFORMANCE:
Swing speed RPM 11.0 11.0 11.0 12.0
Max travel speed km/h (MPH) Hi 5.1 (3.2) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 3.6 (2.2)
Lo 2.9 (1.8) Lo 2.7 (1.7) Lo 2.7 (1.7) Lo 3.4 (2.1)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA4D95LE S4D102E S4D102E SAA4D102E
No. of cylinders- mm 4-95 × 115 4-102 × 120 4-102 × 120 4-102 x 120
bore × stroke (in) (3.74 × 4.53) (4.02 × 4.72) (4.02 × 4.72) (4.02 x 4.72)
Piston displacement ltr. (cu.in) 3.26 (199) 3.92 (239) 3.92 (239) 3.92 (239)
HYDRAULIC SYSTEM: 1 × Variable 1 × Variable 1 × Variable 2 x Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 226 (60) 226 (60) 226 (60) 312 (82.4)
Max. oil pressure kg/cm2 (PSI) 355 (5050)** 355 (5050)** 325 (4620) 380 (5400)
Track shoe width/ mm (in)/ 600 (24)/ 500 (20)/ 700 (28)/ 500 (20)/
ground pressure kg/cm2 (PSI) 0.35 (5.0) 0.41 (5.8) 0.31 (4.4) 0.47 (6.7)
CAPACITY (Refilled):
Fuel tank 200 (52.8) 230 (60.8) 230 (60.8) 280 (74)
Hydraulic oil tank ltr. (U.S. Gal) 69 (18.2) 100 (26.4) 100 (26.4) 121 (32.0)
MACHINE SPEC:
Boom mm (ft.in) 4600 (15'1") 4600 (15'1") 4600 (15'1") 5150 (16'11")
Arm mm (ft.in) 2500 (8'2") 2500 (8'2") 2900 (9'6") 2610 (8'7")
Bucket (SAE) m 3 (cu.yd) 0.50 (0.65) 0.50 (0.65) 0.68 (0.89) 0.65 (0.85)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** For USA
2A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC160LC-7*5 PC160LC-7 PC180LC-7 PC200-7***
Item
Source Japan, UK UK UK Japan
OPERATING WEIGHT* kg (lb) 16620 (36,740) 16400 (36,160) 17700 (39,020) 19500 (42,990)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 110 (82.4)/2200 111 (82)/2200 111 (82)/2200 143 (107)/1950
BUCKET CAPACITY RANGE 0.45 ~ 0.95 0.27 ~ 0.95 0.40 ~ 1.14 0.50 ~ 1.17
(SAE) m 3 (cu.yd) (0.59) (1.24) (0.35) (1.24) (0.52) (1.49) (0.65) (1.53)
PERFORMANCE:
Swing speed RPM 12.0 12.0 12.0 12.4
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Model
PC200-7*4 PC200-7 PC200-7 PC200-7
Item
Source Japan China Indonesia
OPERATING WEIGHT* kg (lb) 19500 (42,990) 20010 (44,110) 19700 (43,430) 20785 (45,820)
FLYWHEELHORSEPOWER (SAE) HP (kW)/RPM 143 (107)/1950 143 (107)/1950 143 (107)/1950 143 (107)/1950
BUCKET CAPACITY RANGE 0.50 ~ 1.17 0.8 0.80 ~ 1.60 0.93
(SAE) m 3 (cu.yd) (0.65) (1.53) (1.05) (1.05) (1.31) (1.21)
PERFORMANCE:
Swing speed RPM 12.4 12.4 12.4 12.4
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.1 (2.5) Mi 4.1 (2.5) Mi 4.1 (2.5)
Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 × 120 6-102 × 120 6-102 x 120 6-102 x 120
bore × stroke (in) (4.02 × 4.72) (4.02 × 4.72) (4.02 x 4.72) (4.02 x 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 x Variable 2 x Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 428 (113) 428 (113) 428 (113) 428 (113)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 600 (24)/ 800 (32)/ 600 (24)/ 800 (32)/
ground pressure kg/cm2 (PSI) 0.46 (6.5) 0.35 (4.98) 0.46 (6.5) 0.36 (5.12)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 400 (105.7) 400 (105.7) 400 (105.7)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 143 (37.8) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5700 (18'8") 5700 (18'8") 5700 (18'8") 5700 (18'8")
Arm mm (ft.in) 2925 (9'7") 2925 (9'7") 2925 (9'7") 2925 (9'7")
Bucket (SAE) m 3 (cu.yd) 0.80 (1.05) 0.80 (1.05) 0.8 (1.05) 0.93 (1.22)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*5 For USA
2A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC200-7SEF PC200LC-7*** PC200LC-7*4 PC200LC-7
Item
Source Indonesia Japan Japan USA
OPERATING WEIGHT* kg (lb) 21200 (46,740) 20900 (46,080) 20900 (46,080) 20700 (45,640)
143 (107)/1950 143 (107)/1950 143 (107)/1950 143 (106.6)/1950
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM
145 (107)/1950 145 (107)/1950 145 (107)/1950 145 (106.6)/1950
BUCKET CAPACITY RANGE 1.3 0.50 ~ 1.17 0.50 ~ 1.17 0.48 ~ 1.53
(SAE) m 3 (cu.yd) (1.7) (0.65) (1.53) (0.65) (1.53) (0.66) (2.0)
PERFORMANCE:
Swing speed RPM 12.4 12.4 12.4 12.4
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.1 (2.5) Mi 4.1 (2.5)
Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 x 120 6-102 × 120 6-102 × 120 6-102 × 120
bore × stroke (in) (4.02 x 4.72) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 x Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 428 (113) 428 (113) 428 (113) 428 (113)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 800 (32)/ 700 (28)/ 700 (28)/ 700 (28)/
ground pressure kg/cm2 (PSI) 0.37 (5.26) 0.38 (5.4) 0.38 (5.4) 0.37 (5.26)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 400 (105.7) 400 (105.7) 400 (105.7)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 143 (37.8) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5200 (17'8") 5700 (18'8") 5700 (18'8") 5700 (18'8")
Arm mm (ft.in) 1900 (6'3") 2925 (9'7") 2925 (9'7") 2925 (9'7")
Bucket (SAE) m 3 (cu.yd) 1.3 (1.7) 0.80 (1.05) 0.80 (1.05) 0.80 (1.05)
Model
PC200LC-7 PC210-7 PC210-7 PC210LC-7
Item
Source China UK China UK
OPERATING WEIGHT* kg (lb) 21100 (46,520) 20575 (45,360) 19800 (43,650) 21575 (47,560)
FLYWHEEL (SAE) HP (kW)/RPM
143 (107)/1950 143 (107)/1950 143 (107)/1950 143 (107)/1950
HORSEPOWER: (DIN) PS (kW)/RPM
BUCKET CAPACITY RANGE 0.80 ~ 1.00 0.48 ~ 1.68 0.80 ~ 1.00 0.48 ~ 1.68
(SAE) m 3 (cu.yd) (1.05) (1.31) (0.63) (2.2) (1.05) (1.31) (0.63) (2.2)
PERFORMANCE:
Swing speed RPM 12.4 12.4 12.4 12.4
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.1 (2.5) Mi 4.5 (2.8) Mi 4.1 (2.5) Mi 4.5 (2.8)
Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 x 120 6-102 × 120 6-102 x 120 6-102 × 120
bore × stroke (in) (4.02 x 4.72) (4.02 × 4.72) (4.02 x 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 x Variable 2 × Variable 2 x Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 428 (113) 428 (113) 428 (113) 428 (113)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 600 (24)/ 600 (24)/ 600 (24)/ 700 (28)/
ground pressure kg/cm2 (PSI) 0.45 (6.4) 0.48 (6.8) 0.46 (6.5) 0.39 (5.5)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 400 (105.7) 400 (105.7) 400 (105.7)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 143 (37.8) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5700 (18'8") 5700 (18'8") 5700 (18'8") 5700 (18'8")
Arm mm (ft.in) 2925 (9'7") 2900 (9'6") 2925 (9'7") 2900 (9'6")
Bucket (SAE) m 3 (cu.yd) 0.80 (1.05) 0.96 (1.25) 0.90 (1.18) 0.96 (1.25)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*4 Deluxe spec.
2A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC210NLC-7 PC210LC-7 PC220-7*** PC220-7*4
Item
Source UK China Japan Japan
OPERATING WEIGHT* kg (lb) 21075 (46,460) 21200 (46,740) 22840 (50,350) 22840 (50,350)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 143 (107)/1950 143 (107)/1950 168 (125)/2200 168 (125)/2200
BUCKET CAPACITY RANGE 0.48 ~ 1.49 0.80 ~ 1.00 0.72 ~ 1.26 0.72 ~ 1.26
(SAE) m 3 (cu.yd) (0.63) (1.9) (1.05) (1.31) (0.94) (1.65) (0.94) (1.65)
PERFORMANCE:
Swing speed RPM 12.4 12.4 11.7 11.7
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.5 (2.8) Mi 4.1 (2.5) Mi 4.2 (2.6)
Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.1 (1.9) Lo 3.1 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 × 120 6-102 x 120 6-102 × 120 6-102 × 120
bore × stroke (in) (4.02 × 4.72) (4.02 x 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 × Variable 2 x Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 428 (113) 428 (113) 439 (116) 439 (116)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 500 (20)/ 600 (24)/ 600 (24)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.53 (7.5) 0.45 (6.4) 0.51 (7.3) 0.51 (7.3)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 400 (105.7) 400 (105.7) 400 (105.7)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 143 (37.8) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5700 (18'8") 5700 (18'8") 5850 (19'2") 5850 (19'2")
Arm mm (ft.in) 2900 (9'6") 2925 (9'7") 3045 (10'0") 3045 (10'0")
Bucket (SAE) m 3 (cu.yd) 0.96 (1.25) 0.90 (1.18) 1.0 (1.31) 1.0 (1.31)
Model
PC220-7 PC220LC-7*** PC220LC-7*4 PC220LC-7
Item
Source China Japan Japan USA
OPERATING WEIGHT* kg (lb) 22900 (50,490) 24270 (53,510) 24270 (53,510) 24510 (54,046)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 168 (125)/2000 168 (125)/2200 168 (125)/2200 168 (125)/2000
BUCKET CAPACITY RANGE 0.72 ~ 1.26 0.72 ~ 1.26 0.72 ~ 1.26 0.48 ~ 1.74
(SAE) m 3 (cu.yd) (0.94) (1.65) (0.94) (1.65) (0.94) (1.65) (0.63) (2.20)
PERFORMANCE:
Swing speed RPM 11.7 11.7 11.7 11.7
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.2 (2.6) Mi 4.2 (2.6) Mi 4.2 (2.6)
Lo 3.1 (1.9) Lo 3.1 (1.9) Lo 3.1 (1.9) Lo 3.1 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 x 120 6-102 × 120 6-102 × 120 6-102 × 120
bore × stroke (in) (4.02 x 4.72) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 x Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 432 (114) 439 (116) 439 (116) 439 (116)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 600 (24)/ 700 (28)/ 700 (28)/ 800 (31.5)/
ground pressure kg/cm2 (PSI) 0.51 (7.3) 0.42 (6.0) 0.42 (6.0) 0.38 (5.4)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 400 (105.7) 400 (105.7) 400 (105.7)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 143 (37.8) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5850 (19'2") 5850 (19'2") 5850 (19'2") 5850 (19'2")
Arm mm (ft.in) 3045 (10'0") 3045 (10'0") 3045 (10'0") 3045 (10'0")
Bucket (SAE) m 3 (cu.yd) 1.0 (1.31) 1.0 (1.31) 1.0 (1.31) 1.0 (1.31)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*4 Deluxe spec.
2A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC220LC-7 PC228US-3 PC228USLC-3 PC230NHD-7*5
Item
Source China Japan Japan UK
OPERATING WEIGHT* kg (lb) 24200 (53,350) 21680 (47,800) 22980 (50,660) 22600 (49,820)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 168 (125)/2000 143 (107)/1950 143 (107)/1950 143 (107)/1950
BUCKET CAPACITY RANGE 0.72 ~ 1.26 0.50 ~ 1.05 0.50 ~ 1.05 0.48 ~ 1.68
(SAE) m 3 (cu.yd) (0.94) (1.65) (0.65) (1.37) (0.65) (1.37) (0.63) (2.20)
PERFORMANCE:
Swing speed RPM 11.7 11.0 11.0 11.9
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.4 (3.4)
Mi 4.2 (2.6) Mi 4.1 (2.5) Mi 4.1 (2.5) Mi 3.6 (2.2)
Lo 3.1 (1.9) Lo 3.0 (1.9) Lo 3.4 (2.1) Lo 2.6 (1.6)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 x 120 6-102 ×120 6-102 × 120 6-102 x 120
bore × stroke (in) (4.02 x 4.72) (4.02 × 4.72) (4.02 × 4.72) (4.02 x 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 x Variable 2 × Variable 2 × Variable 2 x Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 432 (114) 428 (113) 428 (113) 428 (113)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 600 (24)/ 600 (24)/ 700 (28)/ 550 (22)/
ground pressure kg/cm2 (PSI) 0.50 (7.1) 0.51 (7.25) 0.42 (6.0) 0.55 (4.3)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 320 (84.5) 320 (84.5) 400 (105.7)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 126 (33.3) 126 (33.3) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5850 (19'2") 5700 (18'8") 5700 (18'8") 5700 (18'8")
Arm mm (ft.in) 3045 (10'0") 2925 (9'7") 2925 (9'7") 2900 (9'6")
Bucket (SAE) m 3 (cu.yd) 1.0 (1.31) 0.8 (1.05) 0.8 (1.05) 0.96 (1.26)
Model
PC230NHD-7*6 PC240LC-7 PC240NLC-7 PC270LC-7
Item
Source UK UK UK USA
OPERATING WEIGHT* kg (lb) 23100 (50,930) 24500 (54,010) 23500 (51,810) 28500 (62,830)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 143 (107)/1950 168 (125)/2000 168 (125)/2000 179 (134)/2050
BUCKET CAPACITY RANGE 0.48 ~ 1.68 0.55~1.89 0.55~1.89 0.74 ~ 1.87
(SAE) m 3 (cu.yd) (0.63) (2.20) (0.72) (2.47) (0.72) (2.47) (0.97) (2.45)
PERFORMANCE:
Swing speed RPM 11.9 11.7 11.7 10.5
Max travel speed km/h (MPH) Hi 5.4 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 3.6 (2.2) Mi 4.1 (2.5) Mi 4.1 (2.5) Mi 4.2 (2.6)
Lo 2.6 (1.6) Lo 3.1 (1.9) Lo 3.1 (1.9) Lo 3.1 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D102E SAA6D102E
No. of cylinders- mm 6-102 x 120 6-102 × 120 6-102 × 120 6-102 × 120
bore × stroke (in) (4.02 x 4.72) (4.02 × 4.72) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 5.88 (359) 5.88 (359)
HYDRAULIC SYSTEM: 2 x Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 428 (113) 440 (116) 440 (116) 450 (119)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 550 (22)/ 700 (28)/ 600 (24)/ 700 (28)/
ground pressure kg/cm2 (PSI) 0.57 (8.1) 0.44 (6.3) 0.53 (7.5) 0.51 (7.18)
CAPACITY (Refilled):
Fuel tank 400 (105.7) 400 (106) 400 (106) 400 (105.6)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 143 (37.8) 143 (37.8)
MACHINE SPEC:
Boom mm (ft.in) 5500 (18'1") 5850 (19'2") 5850 (19'2") 5850 (19'2")
Arm mm (ft.in) 2900 (9'6") 3000 (9'10") 3000 (9'10") 3045 (10'0")
Bucket (SAE) m 3 (cu.yd) 0.96 (1.26) 1.11 (1.45) 1.11 (1.45) 1.25 (1.63)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*4 Deluxe spec.
*5 With mono boom
2A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC290LC-7 PC290NLC-7 PC300-7*** PC300-7*4
Item
Source UK UK Japan Japan
OPERATING WEIGHT* kg (lb) 28480 (62,790) 28080 (61,910) 30800 (67,900) 30800 (67,900)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 179 (134)/2050 179 (134)/2050 242 (180)/1900 242 (180)/1900
BUCKET CAPACITY RANGE 0.65 ~ 2.1 0.65 ~ 2.1 0.52~1.40 0.52~1.40
(SAE) m 3 (cu.yd) (0.85) (2.75) (0.85) (2.75) (0.68) (1.83) (0.68) (1.83)
PERFORMANCE:
Swing speed RPM 10.5 10.5 9.5 9.5
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.1 (2.5) Mi 4.1 (2.5) Mi 4.5 (2.8)
Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.2 (2.0) Lo 3.2 (2.0)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D102E SAA6D102E SAA6D114E SAA6D114E
No. of cylinders- mm 6-102 × 120 6-102 × 120 6-114 × 135 6-114 × 135
bore × stroke (in) (4.02 × 4.72) (4.02 × 4.72) (4.49 × 5.31) (4.49 × 5.31)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 8.27 (505) 8.27 (505)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 450 (119) 450 (119) 535 (141) 535 (141)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 700 (28)/ 600 (24)/ 600 (24)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.51 (7.3) 0.58 (8.2) 0.64 (9.1) 0.64 (9.1)
CAPACITY (Refilled):
Fuel tank 400 (106) 400 (106) 605 (160) 605 (160)
Hydraulic oil tank ltr. (U.S. Gal) 143 (37.8) 143 (37.8) 188 (49.7) 188 (49.7)
MACHINE SPEC:
Boom mm (ft.in) 5850 (19'2") 5850 (19'2") 6470 (21'3") 6470 (21'3")
Arm mm (ft.in) 3000 (9'10") 3000 (9'10") 3185 (10'5") 3185 (10'5")
Bucket (SAE) m 3 (cu.yd) 1.16 (1.52) 1.16 (1.52) 1.40 (1.83) 1.40 (1.83)
Model
PC300SE-7 PC300HD-7 PC300-7 PC300LC-7***
Item
Source Indonesia USA China Japan
OPERATING WEIGHT* kg (lb) 33490 (73,830) 36736 (80,990) 31200 (68,780) 31900 (70,330)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 242 (180)/1900 242 (180)/1900 242 (180)/1900 242 (180)/1900
BUCKET CAPACITY RANGE 0.52 ~ 2.1 0.84 ~ 1.82 1.40 ~ 1.60 0.52~1.40
(SAE) m 3 (cu.yd) (0.68) (2.74) (1.10) (2.38) (1.83) (2.09) (0.68) (1.83)
PERFORMANCE:
Swing speed RPM 9.3 9.5 9.5 9.5
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.5 (2.8) Mi 4.5 (2.8)
Lo 3.2 (2.0) Lo 3.2 (2.0) Lo 3.2 (2.0) Lo 3.2 (2.0)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D114E SAA6D114E SAA6D114E SAA6D114E
No. of cylinders- mm 6-114 x 135 6-114 x 135 6-114 × 135 6-114 × 135
bore × stroke (in) (4.49 x 5.31) (4.49 x 5.31) (4.49 × 5.31) (4.49 × 5.31)
Piston displacement ltr. (cu.in) 11.04 (674) 8.27 (505) 8.27 (505) 8.27 (505)
HYDRAULIC SYSTEM: 2 x Variable 2 x Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 535 (141) 535 (141) 535 (141) 535 (141)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 800 (31.5)/ 700 (28)/ 600 (24)/ 700 (28)/
ground pressure kg/cm2 (PSI) 0.50 (7.11) 0.60 (8.52) 0.65 (9.2) 0.52 (7.36)
CAPACITY (Refilled):
Fuel tank 605 (160) 605 (160) 605 (160) 605 (160)
Hydraulic oil tank ltr. (U.S. Gal) 188 (49.7) 188 (49.7) 188 (49.7) 188 (49.7)
MACHINE SPEC:
Boom mm (ft.in) 6470 (21'3") 6470 (21'3") 6470 (21'3") 6470 (21'3")
Arm mm (ft.in) 2220 (7'3") 3185 (10'5") 3185 (10'5") 3185 (10'5")
Bucket (SAE) m 3 (cu.yd) 2.1 (2.74) 0.88 (1.15) 1.40 (1.83) 1.40 (1.83)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*6 With two piece boom
2A-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC300LC-7*4 PC300LC-7 PC308USLC-3*5 PC350-7
Item
Source Japan USA Japan Japan
OPERATING WEIGHT* kg (lb) 31900 (70,330) 33208 (73,210) 32689 (72,066) 32300 (71,210)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 242 (180)/1900 242 (180)/1900 179 (134)/2050 242 (180)/1900
BUCKET CAPACITY RANGE 0.52~1.40 0.84 ~ 1.82 0.67 ~ 1.87 1.40
(SAE) m 3 (cu.yd) (0.68) (1.83) (1.15) (2.38) (0.88) (2.45) (1.83)
PERFORMANCE:
Swing speed RPM 9.5 9.5 9.5 9.5
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 4.6 (2.85) Hi 5.5 (3.4)
Mi 4.5 (2.8) Mi 4.5 (2.8) Mi 4.5 (2.8)
Lo 3.2 (2.0) Lo 3.2 (2.0) Lo 2.9 (1.8) Lo 3.2 (2.0)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D114E SAA6D114E SAA6D102E SAA6D114E
No. of cylinders- mm 6-114 × 135 6-114 × 135 6-102 × 120 6-114 × 135
bore × stroke (in) (4.49 × 5.31) (4.49 × 5.31) (4.02 × 4.72) (4.49 × 5.31)
Piston displacement ltr. (cu.in) 8.27 (505) 8.27 (505) 5.88 (359) 8.27 (505)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 535 (141) 535 (141) 450 (119) 535 (141)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 700 (28)/ 800 (31.5)/ 850 (33.5)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.52 (7.36) 0.47 (6.7) 0.44 (6.3) 0.67 (9.5)
CAPACITY (Refilled):
Fuel tank 605 (160) 605 (160) 390 (103) 605 (160)
Hydraulic oil tank ltr. (U.S. Gal) 188 (49.7) 188 (49.7) 200 (52.8) 188 (49.7)
MACHINE SPEC:
Boom mm (ft.in) 6470 (21'3") 6470 (21'3") 5842 (19'2") 6470 (21'3")
Arm mm (ft.in) 3185 (10'5") 3185 (10'5") 3045 (10'0") 3185 (10'3")
Bucket (SAE) m 3 (cu.yd) 1.40 (1.83) 0.88 (1.15) 1.21 (1.59) 1.40 (1.83)
Model
PC340LC-7 PC340NLC-7 PC350LC-7 PC360-7
Item
Source UK UK Japan China
OPERATING WEIGHT* kg (lb) 33340 (73,500) 32860 (72,440) 33400 (73,630) 33000 (72,750)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 242 (180)/1900 242 (180)/1900 242 (180)/1900 242 (180)/1900
BUCKET CAPACITY RANGE 0.60 ~ 2.38 0.60 ~ 2.38 1.40 1.60
(SAE) m 3 (cu.yd) (0.78) (3.11) (0.78) (3.11) (1.83) (2.09)
PERFORMANCE:
Swing speed RPM 9.5 9.5 9.5 9.5
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.5 (2.8) Mi 4.5 (2.8) Mi 4.5 (2.8) Mi 4.5 (2.8)
Lo 3.2 (2.0) Lo 3.2 (2.0) Lo 3.2 (2.0) Lo 3.2 (2.0)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D114E SAA6D114E SAA6D114E SAA6D114E
No. of cylinders- mm 6-114 × 135 6-114 × 135 6-114 × 135 6-114 × 135
bore × stroke (in) (4.49 × 5.31) (4.49 × 5.31) (4.49 × 5.31) (4.49 × 5.31)
Piston displacement ltr. (cu.in) 8.27 (505) 8.27 (505) 8.27 (505) 8.27 (505)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 536 (142) 536 (142) 535 (141) 535 (141)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 700 (28)/ 600 (24)/ 600 (24)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.54 (7.7) 0.63 (9.0) 0.64 (9.1) 0.0.69 (9.8)
CAPACITY (Refilled):
Fuel tank 605 (160) 605 (160) 605 (160) 605 (160)
Hydraulic oil tank ltr. (U.S. Gal) 188 (49.7) 188 (49.7) 188 (49.7) 188 (49.7)
MACHINE SPEC:
Boom mm (ft.in) 6470 (21'3") 6470 (21'3") 6470 (21'3") 6470 (21'3")
Arm mm (ft.in) 3200 (10'6") 3200 (10'6") 3185 (10'3") 3185 (10'3")
Bucket (SAE) m 3 (cu.yd) 1.38 (1.81) 1.38 (1.81) 1.40 (1.83) 1.60 (2.09)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*4 Deluxe spec.
*5 For USA.
2A-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC380LC-7 PC400-7*** PC400-7*4 PC400-6
Item
Source UK Japan Japan China
OPERATING WEIGHT* kg (lb) 40300 (88,850) 41400 (91,270) 41400 (91,270) 41400 (91,270)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 242 (180)/1900 330 (246)/1850 330 (246)/1850 306 (228)/2050
BUCKET CAPACITY RANGE 1.12 ~ 2.54 1.3 ~ 2.2 1.3 ~ 2.2 1.3 ~ 2.2
(SAE) m 3 (cu.yd) (1.46) (3.32) (1.7) (2.9) (1.7) (2.9) (1.7) (2.9)
PERFORMANCE:
Swing speed RPM 9.5 9.0 9.0 9.3
Max travel speed km/h (MPH) Hi 4.3 (2.7) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 3.4 (2.1) Mi 4.4 (2.7) Mi 4.5 (2.8)
Lo 2.0 (1.2) Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.2 (2.0)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D114E SAA6D125E SAA6D125E SA6D125E
No. of cylinders- mm 6-114 × 135 6-125 × 150 6-125 × 150 6-125 x 150
bore × stroke (in) (4.49 × 5.31) (4.92 × 5.90) (4.92 × 5.90) (4.92 x 5.90)
Piston displacement ltr. (cu.in) 8.27 (505) 11.04 (674) 11.04 (674) 11.04 (674)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 × Variable 2 x Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 536 (142) 690 (182) 690 (182) 652 (172)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 380 (5400)** 355 (5050)
Track shoe width/ mm (in)/ 700 (28)/ 600 (24)/ 600 (24)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.61 (8.7) 0.79 (11.2) 0.79 (11.2) 0.79 (11.2)
CAPACITY (Refilled):
Fuel tank 605 (160) 650 (172) 650 (172) 605 (160)
Hydraulic oil tank ltr. (U.S. Gal) 188 (49.7) 248 (65.5) 248 (65.5) 270 (71.3)
MACHINE SPEC:
Boom mm (ft.in) 6470 (21'3") 7060 (23'2") 7060 (23'2") 7060 (23'2")
Arm mm (ft.in) 3190 (10'6") 3380 (11'1") 3380 (11'1") 3380 (11'1")
Bucket (SAE) m 3 (cu.yd) 1.38 (1.81) 1.90 (2.49) 1.90 (2.49) 1.80 (2.35)
Model
PC400SE-7 PC400LC-7*** PC400LC-7*4 PC400LC-7
Item
Source Indonesia Japan Japan USA
OPERATING WEIGHT* kg (lb) 42840 (94,450) 42850 (94,470) 42850 (94,470) 43869 (96,712)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 330 (246)/2050 330 (246)/1850 330 (246)/1850 330 (246)/1850
BUCKET CAPACITY RANGE 2.8 1.3 ~ 2.2 1.3 ~ 2.2 1.12 ~ 3.17
(SAE) m 3 (cu.yd) (3.66) (1.7) (2.9) (1.7) (2.9) (1.47) (4.15)
PERFORMANCE:
Swing speed RPM 9.3 9.0 9.0 9.0
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.4 (2.7)
Lo 3.2 (2.0) Lo 3.0 (1.9) Lo 3.2 (2.0) Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SA6D125E SAA6D125E SAA6D125E SAA6D125E
No. of cylinders- mm 6-125 x 150 6-125 × 150 6-125 × 150 6-125 × 150
bore × stroke (in) (4.92 x 5.91) (4.92 × 5.90) (4.92 × 5.90) (4.92 × 5.91)
Piston displacement ltr. (cu.in) 11.04 (674) 11.04 (674) 11.04 (674) 11.04 (674)
HYDRAULIC SYSTEM: 2 x Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 652 (172) 690 (182) 690 (182) 690 (182)
Max. oil pressure kg/cm2 (PSI) 355 (5050) 380 (5400)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 800 (31.5)/ 700 (28)/ 700 (28)/ 800 (32)/
ground pressure kg/cm2 (PSI) 0.50 (7.11) 0.66 (9.4) 0.66 (9.4) 0.67 (9.5)
CAPACITY (Refilled):
Fuel tank 605 (160) 650 (172) 650 (172) 650 (172)
Hydraulic oil tank ltr. (U.S. Gal) 188 (49.7) 248 (65.5) 248 (65.5) 248 (65.5)
MACHINE SPEC:
Boom mm (ft.in) 7060 (23'2") 7060 (23'2") 7060 (23'2") 7060 (23'2")
Arm mm (ft.in) 2400 (7'10") 3380 (11'1") 3380 (11'1") 3380 (11'1")
Bucket (SAE) m 3 (cu.yd) 2.8 (3.66) 1.90 (2.49) 1.90 (2.49) 1.94 (2.54)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*4 Deluxe spec.
2A-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC400LC-7*5 PC400LC-7 PC450-7 PC450-7*5
Item
Source USA Indonesia Japan UK
OPERATING WEIGHT* kg (lb) 44837 (98,848) 43890 (96,760) 43000 (94,800) 43080 (94,970)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 330 (246)/1850 330 (246)/2050 330 (246)/1850 330 (246)/1850
BUCKET CAPACITY RANGE 1.12 ~ 3.17 2.8 1.90 ~ 2.10 1.3 ~ 2.7
(SAE) m 3 (cu.yd) (1.47) (4.15) (3.66) (2.49) (2.75) (1.7) (3.53)
PERFORMANCE:
Swing speed RPM 9.0 9.3 9.0 9.0
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 5.5 (3.4)
Mi 4.4 (2.7) Mi 4.4 (2.7)
Lo 3.0 (1.9) Lo 3.2 (2.0) Lo 3.0 (1.9) Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D125E SAA6D125E SAA6D125E SAA6D125E
No. of cylinders- mm 6-125 × 150 6-125 × 150 6-125 × 150 6-125 × 150
bore × stroke (in) (4.92 × 5.91) (4.92 × 5.90) (4.92 × 5.90) (4.92 × 5.90)
Piston displacement ltr. (cu.in) 11.04 (674) 11.04 (673) 11.04 (673) 11.04 (673)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 690 (182) 652 (172) 690 (182) 690 (182)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 355 (5050)** 380 (5400)** 380 (5400)**
Track shoe width/ mm (in)/ 800 (32)/ 600 (24)/ 600 (24)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.67 (9.5) 0.84 (11.9) 0.83 (11.8) 0.83 (11.8)
CAPACITY (Refilled):
Fuel tank 650 (172) 605 (160) 650 (172) 650 (172)
Hydraulic oil tank ltr. (U.S. Gal) 248 (65.5) 270 (71.3) 248 (65.5) 248 (65.5)
MACHINE SPEC:
Boom mm (ft.in) 7060 (23'2") 7060 (23'2") 7060 (23'2") 7060 (23'2")
Arm mm (ft.in) 3380 (11'1") 2400 (7'10") 3380 (11'1") 3380 (11'1")
Bucket (SAE) m 3 (cu.yd) 1.94 (2.54) 2.8 (3.66) 1.90 (2.49) 1.90 (2.49)
Model
PC450LC-7*5 PC450LC-7 PC600-7 PC600LC-7
Item
Source UK Japan Japan Japan
OPERATING WEIGHT* kg (lb) 43780 (96,520) 44000 (97,000) 56600 (124,780) 57600 (126,990)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 330 (246)/1850 330 (246)/1850 385 (287)/180 385 (287)/1800
BUCKET CAPACITY RANGE 1.3 ~ 2.7 1.90 ~ 2.10 2.0 ~ 3.5 2.0 ~ 3.5
(SAE) m 3 (cu.yd) (1.7) (3.53) (2.49) (2.75) (2.62) (4.58) (2.62) (4.58)
PERFORMANCE:
Swing speed RPM 9.0 9.0 8.3 8.3
Max travel speed km/h (MPH) Hi 5.5 (3.4) Hi 5.5 (3.4) Hi 4.9 (3.0) Hi 4.9 (3.0)
Mi 4.4 (2.7) Mi 4.4 (2.7)
Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9) Lo 3.0 (1.9)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model SAA6D125E SAA6D125E SA6D140E SA6D140E
No. of cylinders- mm 6-125 × 150 6-125 × 150 6-140 × 165 6-140 × 165
bore × stroke (in) (4.92 × 5.90) (4.92 × 5.90) (5.51 × 6.50) (5.51 × 6.50)
Piston displacement ltr. (cu.in) 11.04 (67.3) 11.04 (673) 15.24 (930) 15.24 (930)
HYDRAULIC SYSTEM: 2 × Variable 2 × Variable 2 × Variable 2 × Variable
Hydraulic pump Piston Piston Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 690 (182) 690 (182) 820 (216) 820 (216)
Max. oil pressure kg/cm2 (PSI) 380 (5400)** 380 (5400)** 350 (4980)*5 350 (4980) *5
Track shoe width/ mm (in)/ 600 (24)/ 600 (24)/ 600 (24)/ 600 (24)/
ground pressure kg/cm2 (PSI) 0.78 (11.1) 0.79 (11.2) 1.02 (14.5) 0.97 (13.8)
CAPACITY (Refilled):
Fuel tank 650 (172) 650 (172) 880 (232) 880 (232)
Hydraulic oil tank ltr. (U.S. Gal) 248 (65.5) 248 (65.5) 360 (95) 360 (95)
MACHINE SPEC:
Boom mm (ft.in) 7060 (23'2") 7060 (23'2") 7660 (25'2") 7660 (25'2")
Arm mm (ft.in) 3380 (11'1") 3380 (11'1") 3500 (11'6") 3500 (11'6")
Bucket (SAE) m 3 (cu.yd) 1.90 (2.49) 1.90 (2.49) 2.7 (3.53) 2.7 (3.53)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
*** Basic spec.
*4 Deluxe spec.
*5 With variable gauge
2A-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model PC600-6*4
PC600SE-6 PC600LC-6*4 PC750-7
Item QUARRY
Source UK UK UK Japan
OPERATING WEIGHT* kg (lb) 57480 (126,720) 58280 (128,480) 57780 (127,380) 72370 (159,550)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RP 385 (287)/1800 385 (287)/1800 385 (287)/1800 454 (338)/1800
BUCKET CAPACITY RANGE 2.4 ~ 3.5 2.4 ~ 2.8 2.4 ~ 2.8 2.8 ~ 3.4
(SAE) m 3 (cu.yd) (3.14) (4.58) (3.14) (3.66) (3.14) (3.66) (3.66) (4.45)
PERFORMANCE:
Swing speed RPM 8.3 8.3 8.3 6.8
Max travel speed km/h (MPH) Hi 4.9 (3.0) Hi 4.9 (3.0) Hi 4.9 (3.0) Hi 4.2 (2.6)
Model
PC750LC-7*6 PC750SE-7 PC750SE-6*4 PC750LC-6*4
Item
Source Japan Japan UK UK
OPERATING WEIGHT* kg (lb) 77600 (171,080) 73170 (161,310) 76245 (168,090) 80960 (178,480)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 454 (338)/1800 454 (338)/1800 444 (331)/1800 444 (331)/1800
BUCKET CAPACITY RANGE 2.89 ~ 3.7 4.0 ~ 4.5 3.6 ~ 6.0 3.6 ~ 6.0
(SAE) m 3 (cu.yd) (3.78) (4.85) (5.23) (5.89) (4.71) (7.85) (4.71) (7.85)
PERFORMANCE:
Swing speed RPM 6.8 6.8 5.7 5.7
Max travel speed km/h (MPH) Hi 4.2 (2.6) Hi 4.2 (2.6) Hi 4.2 (2.6) Hi 4.2 (2.6)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
* 4
With variable gauge
*5 Travel circuit and heavy lift circuit
2A-24
AH_25.book Page 25 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC800-7 PC800SE-6 PC1250-7 PC1250LC-7
Item
Source Japan Japan Japan Japan
OPERATING WEIGHT* kg (lb) 76070 (167,700) 75570 (166,600) 106700 (235,230) 113200 (249,560)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 454 (338)/1800 454 (338)/1800 651 (485)/1800 651 (485)/1800
BUCKET CAPACITY RANGE 3.4 4.0 ~ 4.5 3.4 ~ 5.2 3.4 ~ 5.2
(SAE) m 3 (cu.yd) (4.45) (5.23) (5.89) (4.45) (6.80) (4.45) (6.80)
PERFORMANCE:
Swing speed RPM 6.8 6.8 5.5 5.5
Max travel speed km/h (MPH) Hi 4.2 (2.6) Hi 4.2 (2.6) Hi 3.2 (2.0) Hi 3.2 (2.0)
Model
PC1250SP-7 PC1800-6
Item
Source Japan Japan
OPERATING WEIGHT* kg (lb) 109500 (241,400) 180000 (396,830)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 651 (485)/1800 908 (676)/1800
BUCKET CAPACITY RANGE 6.7 5.6 ~ 12.0
(SAE) m 3 (cu.yd) (8.76) (7.3) (15.7)
PERFORMANCE:
Swing speed RPM 5.5 4.5
Max travel speed km/h (MPH) Hi 3.2 (2.0) 2.7 (1.7)
Lo 2.1 (1.3)
DIMENSIONS: See the page of
dimensions.
ENGINE: KOMATSU KOMATSU
Model SAA6D170E SAA6D140E x 2
No. of cylinders- mm 6-170 × 170 6-140 × 165
bore × stroke (in) (6.69 × 6.69) (5.51 × 6.50)
Piston displacement ltr. (cu.in) 23.15 (1413) 15.24 × 2 (930 × 2)
HYDRAULIC SYSTEM: 3 × Variable 6 × Variable
Hydraulic pump Piston Piston
Max. oil flow ltr. (U.S. Gal)/min. 1588 (420) 2304 (609)
Max. oil pressure kg/cm2 (PSI) 320 (4550) 320 (4550)**
Track shoe width/ mm (in)/ 700 (28)/ 810 (32)/
ground pressure kg/cm2 (PSI) 1.43 (20.3) 1.73 (24.6)
CAPACITY (Refilled):
Fuel tank 1360 (359) 2750 (727)
Hydraulic oil tank ltr. (U.S. Gal) 670 (177) 1500 (396)
MACHINE SPEC:
Boom mm (ft.in) 7800 (25'7") 8700 (28'7")
Arm mm (ft.in) 3400 (11'2") 3900 (12'10")
Bucket (SAE) m 3 (cu.yd) 6.7 (8.76) 12.0 (15.7)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
* 4
With variable gauge
*5 Travel circuit and heavy lift circuit
2A-25
AH_25.book Page 26 Tuesday, March 23, 2004 9:41 AM
Specifications EXCAVATORS
(BACKHOE)
Model
PC1400-1 PC3000-1 PC4000-6 PC5500-6
Item
Source Germany Germany Germany Germany
500000
OPERATING WEIGHT* kg (lb) 137000 (302,030) 253000 (557,760) 390000 (859,790)
(1,102,300)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 758 (565)/1800 1260 (940)/1800 1875 (1400)/1800 2520 (1880)/1800
BUCKET CAPACITY RANGE 8.5 ~ 9.5 12 ~ 20 16 ~ 28 21 ~ 36
(SAE) m 3 (cu.yd) (11.1) (12.4) (15.7) (26.2) (20.9) (36.6) (27.5) (47.1)
PERFORMANCE:
Swing speed RPM 6.2 4.6 4.0 3.6
Max travel speed km/h (MPH) 2.4 (1.5) 2.4 (1.5) 2.1 (1.3) 2.3 (1.4)
Model
PC8000-6
Item
Source Germany
710000
OPERATING WEIGHT* kg (lb) (1,565,270)
FLYWHEEL HORSEPOWER (SAE) HP (kW)/RPM 4020 (3000)/1800
BUCKET CAPACITY RANGE 28 ~ 48
(SAE) m 3 (cu.yd) (30.9) (52.9)
PERFORMANCE:
Swing speed RPM 3.45
Max travel speed km/h (MPH) 2.14 (1.3)
* Operating weight includes coolant, lubricants, full fuel tank, operator 80kg(180lb) and, indicated implement, shoes and upper
attachment.
** Travel circuit and at Power Max. function
2A-26
AH_25.book Page 27 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E L
D
K
C
G
I
H A
J B FVBH0017
A B C D E F G H I J K L Boom Arm
mm mm mm mm mm mm mm mm mm mm mm mm length length
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) m (ft.in) m (ft.in)
650 915 290 650 570 100 450 130 580 2100 0.92 0.48
PC01-1 — —
(2'2") (3') (11") (2'2") (1'10") (3.9") (1'6") (5") (1'11") (6'11") (3') (1'7")
900 1225 350 790 700 2100 180 520 180 700 2730 1.357 0.684
PC09-1 —
(2'11") (4') (1'2") (2'7") (2'4") (6'11") (7.1") (1'8") (7") (2'4") (8'11") (4'5") (2'3")
3626 0.88
1015 437 1070 2229 770 230 1000 (11'11") (2'11")
PC12R-8 — —
(3'4") (1'5") (3'6") (7'4") (2'6") (9") (3'3") 3647 1.13
(12') (3'8")
770/ 1000/ 3570 0.965
1212 1555 440 790 2430 205 (2'6") 230 (3'3") 690 (11'9") 1.76 (3'2")
PC15MRX-1
(4'0") (5'1") (1'5") (2'7") (8'10") (8.1") 1020 (9") 1250 (2'3") (5'6") 1.125
(3'4") (4'1") (4'0")
3745 0.965
1015 437 1070 2229 770 230 1000 (12'3") (3'2")
PC15R-8 — —
(3'4") (1'5") (3'6") (7'4") (2'6") (9") (3'3") 3780 1.215
(12'5") (4')
3930 0.93
1440 1895 540 925 1390 2410 285 1200 250 1450 800 (12'11") 1.81 (3'1")
PC20MRX-1
(4'9") (6'3") (1'9") (3'0") (4'7") (7'9") (11.2") (3'11") (10") (4'9") (2'8") (5'11") 1.28
(4'2")
4250 1.07
1340 545 1240 1420 2450 1120 250 1430 (13'11") (3'6")
PC20R-8 —
(4'5") (1'9") (4'1") (4'8") (8'1") (3'8") (10") (4'8") 4320 1.32
(14'2") (4'4")
4140 1.11
1485 1955 560 955 1530 2460 320 1250 300 1550 (13'7") 2.12 (3'8")
PC27MRX-1* —
(4'10") (6'5") (2'2") (3'2") (5'0") (8'1") (12.6") (4'1") (12") (5'1") 4230 (6'11") 1.41
(13'11") (4'8")
4525 1.2
1485 585 1240 2490 1200 300 1500 (14'10") (3'11")
PC27R-8 —
(4'10") (1'11") (4'1") (8'2") (3'11") (12") (4'11") 4655 1.5
(15'3") (4'11")
4630 1.26
1650 2105 545 1050 1485 2530 320 1250 300 1550 855 (15'2") 2.35 (4'1")
PC30MR-2*
(5'5") (6'11") (1'9") (3'5") (4'10") (8'4") (12.6") (4'1") (12") (5'1") (2'10") 4660 (7'9") 1.66
(15'3") (5'5")
4850 1.35
1650 2105 545 1050 1485 2530 320 1440 300 1740 950 (15'11") 2.56 (4'5")
PC35MR-2*
(5'5") (6'11") (1'9") (3'5") (4'10") (8'4") (12.6") (4'9") (12") (5'9") (3'1") 4930 (8'5") 1.75
(16'2") (5'9")
5090 1.35
1610 580 1415 2500 1220 300 1520 (16'8") (4'5")
PC35R-8 —
(5'3") (1'11") (4'8") (8'2") (4') (12") (5') 5155 1.75
(16'11") (5'9")
5390 1.44
2000 2520 625 1265 1835 2625 320 1560 400 1960 1060 (17'8") 2.74 (4'9")
PC40MR-2*
(6'7") (8'3") (2'1") (4'2") (6'0") (8'7") (12.6") (5'1") (16") (6'5") (3'6") 5450 (9'0") 1.9
(17'11") (6'3")
5485 1.48
1910 640 1470 2560 1500 400 1900 (18') (4'10")
PC45R-8 —
(6'3") (2'1") (4'10") (8'5") (4'11") (16") (6'3") 5555 1.9
(18'3") (6'3")
5550 1.64
2000 2520 625 1265 1835 2625 320 1560 400 1960 1060 (18'3") 2.90 (5'5")
PC50MR-2* (6'7") (8'3") (2'1") (4'2") (6'0") (8'7") (12.6") (5'1") (16") (6'5") (3'6") (9'6")
5615 2.0
(18'5") (6'7")
2A-27
AH_25.book Page 28 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
5875 1.7
2200 2785 750 1475 2000 2690 400 1650 450 2050 1690 (19'3") (5'7")
PC75R-2
(7'3") (9'2") (2'6") (4'10") (6'7") (8'10) (1'4") (5'5") (18") (6'9") (5'7") 2.1
(6'11")
6286 2465 1.65
2235 2840 735 1240 2330 2730 360 1870 450 2320 1745 (20'7") (8'1") 3.71 (5'5")
PC78US-6
(7'4") (9'4") (2'5") (4'1") (7'8") (8'11") (1'2") (6'2") (18") (7'7") (5'9") 5785 2830 (12'2") 2.25
(19'0") (9'3") (7'5")
6200 2200 1.65
2235 2840 735 1260 2330 2730 360 1870 450 2320 1745 (20'4") (7'3") 3.40 (5'5")
PC78MR-6
(7'4") (9'4") (2'5") (4'2") (7'8") (8'11") (1'2") (6'2") (18") (7'7") (5'8") (11'2") 2.25
(7'5")
6150 2300 1.85
2340 785 1510 2120 2695 430 1800 450 2200 1715 (20'2") (7'7") 2.95 (6'1")
PC95R-2
(7'8") (2'7") (4'11") (6'11") (8'10") (1'5") (5'11") (18") (7'3") (5'8") 6205 2700 (9'8") 2.3
(20'4") (7'7") (7'7")
PC100F-6 2890 3755 1120 2130 2455 3135 600 1960 900 2860 2050 7475 2686 4.26 2.36
(LOGGING) (9'5") (12'3") (3'7") (7') (8'1") (10'3") (2') (6'4") (35.4") (9'4") (6'9") (24'6") (8'8") (14') (7'9")
PC100F-6 2890 3755 1120 2130 2455 2960 600 1960 900 2860 2050 7175 2720 4.26 2.36
(AGRO) (9'5") (12'3") (3'7") (7') (8'1") (9'7") (2') (6'4") (35.4") (9'4") (6'9") (23'6") (8'11") (14') (7'9")
PC100F-6Z 2890 3755 1120 2130 2455 2960 600 1960 900 2860 2050 7175 2720 4.26 2.36
(AGRO ECO) (9'5") (12'3") (3'7") (7') (8'1") (9'7") (2') (6'4") (35.4") (9'4") (6'9") (23'6") (8'11") (14') (7'9")
1.85
(6'1")
2420 868 1577 2120 2790 1900 500 2400 6480 2715 2.0
PC110R-1
(7'11") (2'10") (5'2") (6'11") (9'2") (6'3") (20") (7'10") (21'3") (8'11) (6'7")
2.3
(7'7")
7590 2620 2.1
(24'11") (8'7") (6'11")
PC120-6 2750 3480 855 2110 2455 2715 400 1960 500 2460 1805 7595 2715 4.6 2.5
(9') (11'5") (2'10") (6'11") (8'1") (8'11") (1'4") (6'5") (20") (8'1") (5'11") (24'11") (8'11") (15'1") (8'2")
7510 3075 3.0
(24'8") (10'1") (9'10")
7590 2620 2.1
(24'11") (8'7") (6'11")
2750 3480 855 2110 2455 2715 400 1960 600 2560 1805 7595 2715 4.6 2.5
PC120-6*
(9') (11'5") (2'10") (6'11") (8'1") (8'11") (1'4") (6'5") (24") (8'5") (5'11") (24'11") (8'11") (15'1") (8'2")
7510 3075 3.0
(24'8") (10'1") (9'10")
7590 2620 2.1
(24'11") (8'7") (6'11")
3100 3830 895 2110 2445 2755 400 1990 600 2590 1845 7595 2715 4.6 2.5
PC120LC-6*
(10'2") (12'7") (2'11") (6'11") (8'1") (8'11") (1'4") (6'6") (24") (8'6") (6'1") (24'11") (8'11") (15'1") (8'2")
7510 3075 3.0
(24'11") (10'1") (9'10")
7225 2630 2.1
(23'8") (8'8") (6'11")
2880 3610 895 1480 2515 2815 390 1990 500 2490 1975 7260 2850 4.6 2.5
PC138US-2
(9'5") (11'10") (2'11") (4'10") (8'3") (9'3") (1'3") (6'6") (20") (8'2") (6'6") (23'10") (9'4") (15'1") (8'2")
7120 3190 3.0
(23'4") (10'6") (9'10")
7410 2690 2.1
(24'4") (8'10") (6'11")
PC138USLC 3110 3480 895 1480 2515 2815 390 1990 600 2590 1975 7395 2850 4.6 2.5
-2*5 (10'2") (12'7") (2'11") (4'10") (8'3") (9'3") (1'3") (6'6") (24") (8'6") (6'6") (24'3") (9'4") (15'1") (8'2")
7295 3190 3.0
(23'11") (10'6") (9'10")
* For USA
2A-28
AH_25.book Page 29 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
7590 2.1
(24'11") 2620 (6'11")
7595 (8'7") 2.5
2750 3480 855 2130 2455 2715 400 1960 500 2460 1805 (24'11") 4.6 (8'2")
PC130-6** 2715
(9') (11'5") (2'10") (7') (8'1") (8'11") (1'4") (6'5") (20") (8'1") (5'11") (15'1")
(8'11")
7510 2.9
(24'8") 3075 (9'6")
(10'1")
PC130-6 2750 3480 855 2110 2480 2715 400 1960 500 2460 1805 7595 2715 4.6 2.5
MIGHTY (9') (11'5") (2'10") (6'11") (8'2") (8'11") (1'4") (6'5") (20") (8'1") (5'11") (24'11") (8'11") (15'1") (8'2")
8565 2990 2.25
(28'1") (9'10") (7'5")
3170 3965 1055 2390 2490 2970 440 1990 500 2490 2090 8565 3000 5.15 2.61
PC160LC-7
(10'5") (13'0") (3'6") (7'10") (8'2") (9'9") (1'5") (6'6") (20") (8'2") (6'10") (28'1") (9'10") (16'11") (8'7")
8565 3100 2.9
(28'1") (10'2") (9'6")
8565 2990 2.25
(28'1") (9'10") (7'5")
3170 3965 1055 2390 2490 2970 440 1990 500 2490 2090 8565 3000 5.15 2.61
PC160LC-7**
(10'5") (13'0") (3'6") (7'10") (8'2") (9'9") (1'5") (6'6") (20") (8'2") (6'10") (28'1") (9'10") (16'11") (8'7")
8565 3100 2.9
(28'1") (10'2") (9'6")
8565 3000 2.61
3170 3965 1055 2390 2490 2970 440 1990 600 2590 2090 (28'1") (9'10") 5.15 (8'7")
PC160LC-7*** (10'5") (13'0") (3'6") (7'10") (8'2") (9'9") (1'5") (6'6") (24") (8'6") (6'10") 8565 3100 (16'11") 2.9
(28'1") (10'2") (9'6")
8565 2990 2.25
(28'1") (9'10") (7'5")
3270 4065 1055 2390 2490 2970 440 2200 600 2800 2090 8565 3000 5.15 2.61
PC180LC-7
(10'9") (13'4") (3'6") (7'10") (8'2") (9'9") (1'5") (7'3") (24") (9'2") (6'10") (28'1") (9'10") (16'11") (8'7")
8565 3100 2.9
(28'1") (10'2") (9'6")
9480 2985 1.84
(3'1") (9'10") (6'0")
PC200-7
PC200-7*4 3270 4080 1085 2710 2710 3000 440 2200 600 2800 2095 9495 3190 5.7 2.41
(10'9") (13'5") (3'7") (8'11") (8'11") (9'10") (1'5") (7'3") (24") (9'2") (6'10") (3'2") (10'6") (18'8") (7'11")
PC210-7*4
9425 2970 2.925
(30'11") (9'9") (9'7")
9495 3190 2.41
3270 4080 1085 2710 2710 3000 440 2200 800 3000 2095 (31'2") (10'6") 5.7 (7'11")
PC200-7*
(10'9") (13'5") (3'7") (8'11") (8'11") (9'10") (1'5") (7'3") (31.5") (9'10") (6'10") 9425 2970 (18'8") 2.925
(30'11") (9'9") (9'7")
3270 4080 1085 2710 2710 3000 440 2200 800 3000 2095 9110 3280 5.2 1.9
PC200-7SEF
(10'9") (13'5") (3'7") (8'11") (8'11") (9'10") (1'5") (7'3") (31.5") (9'10") (6'10") (29'10") (10'10") (17'1") (6'6")
3270 4080 1085 2710 2710 3000 440 2200 800 3000 2095 11710 3310 8.04 6.36
PC200-7SLF
(10'9") (13'5") (3'7") (8'11") (8'11") (9'10") (1'5") (7'3") (31.5") (9'10") (6'10") (38'5") (10'10") (26'4") (20'10")
9480 2985 1.84
(31'1") (9'10") (6'0")
PC200LC-7 3640 4450 1085 2710 2710 3000 440 2380 700 3080 2095 9495 3190 5.7 2.41
PC200LC-7*4 (1'11") (14'7") (3'7") (8'11") (8'11") (9'10") (1'5") (7'10") (28") (10'1") (6'10") (31'2") (10'6") (18'8") (7'11")
PC210LC-7*4
9425 2970 2.925
(30'11") (9'9") (9'7")
* USA source
** UK source
*** For USA
*4 China source
2A-29
AH_25.book Page 30 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
9495 3190 2.41
3640 4450 1085 2710 2710 3000 440 2380 700 3080 2095 (31'2") (10'6") 5.7 (7'11")
PC200LC-7*
(1'11") (14'7") (3'7") (8'11") (8'11") (9'10") (1'5") (7'10") (28") (10'1") (6'10") 9425 2970 (18'8") 2.925
(30'11") (9'9") (9'7")
9540 2985 1.8
(31'4") (9'10") (5'11")
PC210-7** 3270 4080 1100 2770 2515 3015 440 2200 600 2800 2110 9555 3190 5.7 2.4
(10'9") (13'5") (3'7") (9'1") (8'3") (9'11") (1'5") (7'3") (24") (9'2") (6'11") (31'4") (10'6") (18'8") (7'10")
9485 2970 2.9
(31'1") (9'9") (9'6")
9540 2985 1.8
(31'4") (9'10") (5'11")
PC210LC-7** 3640 4450 1100 2770 2515 3015 440 2380 700 3080 2110 9555 3190 5.7 2.4
(11'11") (14'7") (3'7") (9'1") (8'3") (9'11") (1'5") (7'10") (28") (10'1") (6'11") (31'4") (10'6") (18'8") (7'10")
9485 2970 2.9
(31'1") (9'9") (9'6")
9540 2985 1.8
(31'4") (9'10") (5'11")
3640
PC210NLC-7** (11'11") 4450 1100 2770 2515 3015 440 2040 500 2540 2110 9555 3190 5.7 2.4
(14'7") (3'7") (9'1") (8'3") (9'11") (1'5") (6'8") (20") (8'4") (6'11") (31'4") (10'6") (18'8") (7'10")
9485 2970 2.9
(31'1") (9'9") (9'6")
9865 3220 2.0
(32'4") (10'7") (6'7")
PC220-7 3460 4265 1100 2905 2710 3015 440 2380 600 2980 2110 9960 3295 5.85 2.5
(11'4") (14'0") (3'7") (9'6") (8'11") (9'11") (1'5") (7'10") (24") (9'9") (6'11") (32'8") (10'10") (19'2") (8'2")
9885 3160 3.045
(32'5") (10'4") (10'0")
9865 3220 2.0
(32'4") (10'7") (6'7")
9960 3295 2.5
3460 4265 1100 2905 2710 3015 440 2380 600 2980 2110 (32'8") (10'10") 5.85 (8'2")
PC220-7*** (11'4") (14'0") (3'7") (9'6") (8'11") (9'11") (1'5") (7'10") (24") (9'9") (6'11") (19'2")
9885 3160 3.05
(32'5") (10'9") (10')
9910 3265 3.5
(32'6") (10'9") (11'6")
9865 3220 2.0
(32'4") (10'7") (6'7")
PC220LC-7 3845 4640 1100 2905 2710 3015 440 2580 700 3280 2110 9960 3295 5.85 2.5
(12'7") (15'3") (3'7") (9'6") (8'11") (9'11") (1'5") (8'6") (28") (10'9") (6'11") (32'8") (10'10") (19'2") (8'2")
9885 3160 3.045
(32'4") (10'4") (10'0")
9885 3160 3.045
3845 4640 1100 2905 2710 3015 440 2580 800 3380 2110 (32'5") (10'4") 5.85 (10'0")
PC220LC-7* (12'7") (15'3") (3'7") (9'6") (8'11") (9'11") (1'5") (8'6") (31.5") (11'1") (6'11") (19'2") 3.505
9910 3270
(32'6") (10'9") (11'6")
9865 3220 2.0
(32'4") (10'7") (6'7")
9960 3295 2.5
3845 4640 1100 2905 2710 3015 440 2580 600 3180 2110 (32'8") (10'10") 5.85 (8'2")
PC220LC-7*** (12'7") (15'3") (3'7") (9'6") (8'11") (9'11") (1'5") (8'6") (24") (10'5") (6'11") (19'2")
9885 3160 3.05
(32'5") (10'9") (10')
9910 3265 3.5
(32'6") (10'9") (11'6")
PC228US-3 3270 4080 1060 1680 2980 3010 440 2200 600 2800 2285 8700 2980 5.7 2.9
(10'9") (13'5") (3'6") (5'6") (9'9") (9'11") (1'5") (7'3") (24") (9'2") (7'6") (28'7") (9'9") (18'8") (9'6")
3640
PC228USLC-3 (11'11") 4450 1060 1680 2980 3010 440 2380 700 3080 2285 8890 2980 5.7 2.9
(14'7") (3'6") (5'6") (9'9") (9'11") (1'5") (7'10") (28") (10'1") (7'6") (29'2") (9'9") (18'8") (9'6")
* USA source
** UK source
*** China source
2A-30
AH_25.book Page 31 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
A B C D E F G H I J K M N Boom Arm
mm mm mm mm mm mm mm mm mm mm mm mm mm length length
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in) m m
(ft.in) (ft.in)
9540 2985 1.8
(31'4") (9'10") (5'11")
3460 4305 1125 2770 2515 3040 465 1990 550 2540 2135 9555 3190 5.7 2.4
PC230-7NHD*
(11'4") (14'1") (3'8") (9'1") (8'3") (10'0") (1'6") (6'6") (22") (8'4") (7'0") (31'4") (10'6") (18'8") (7'10")
9485 2970 2.9
(31'1") (9'9") (9'6")
9935 3270 1.8
(32'7") (10'9") (5'11")
3460 4305 1125 2770 2515 3040 465 1990 550 2540 2135 9790 3535 5.5 2.4
PC230-7NHD**
(11'4") (14'1") (3'8") (9'1") (8'3") (10'0") (1'6") (6'6") (22") (8'4") (7'0") (32'1") (11'7") (18'1") (7'10")
9775 3510 2.9
(32'1") (11'6") (9'6")
9865 3220 2.0
(21'9") (10'7") (6'7")
9960 3295 2.5
3845 4640 1100 2905 2710 3015 440 2580 700 3280 2110 (32'8") (10'10") 5.85 (8'2")
PC240LC-7
(12'7") (15'3") (3'7") (9'6") (8'11") (9'11") (1'5") (8'6") (28") (10'9") (6'11") 9885 3160 (19'2") 3.0
(32'5") (10'4") (9'10")
9910 3270 3.5
(32'6") (10'9") (11'6")
9865 3220 2.0
(21'9") (10'7") (6'7")
9960 3295 2.5
3640 4450 1100 2905 2710 3015 440 2380 600 2980 2110 (32'8") (10'10") 5.85 (8'2")
PC240NLC-7
(11'11") (14'7") (3'7") (9'6") (8'11") (9'11") (1'5") (7'10") (24") (9'9") (6'11") 9885 3160 (19'2") 3.0
(32'5") (10'4") (9'10")
9910 3270 3.5
(32'6") (10'9") (11'6")
— — —
4030 4955 1180 2905 2710 3100 498 2590 700 3290 2200 9790 3210 5.85 3.05
PC270LC-7
(13'3") (16'3") (3'10") (9'4") (8'11") (9'11") (1'8") (8'6") (28") (10'10") (7'3")
(32'1") (10'6") (19'2") (10'0")
9890 3290 3.5
(32'5") (10'10") (11'6")
9820 3200 2.0
(32'3") (10'6") (6'7")
9940 3320 2.5
3700 4625 1186 2905 2710 3100 498 2590 700 3290 2200 (32'7") (10'11") 5.85 (8'2")
PC290LC-7
(12'2") (15'2") (3'11") (9'6") (8'11") (10'2") (1'8") (8'6") (28") (10'10") (7'3") 9790 3210 (19'2") 3.05
(32'1") (10'6") (10'0")
9890 3280 3.5
(32'5") (10'9) (11'6")
9820 3200 2.0
(32'3") (10'6") (6'7")
9940 3320 2.5
3700 4625 1186 2905 2710 3100 498 2390 700 3090 2200 (32'7") (10'11") 5.85 (8'2")
PC290NLC-7
(12'2") (15'2") (3'11") (9'6") (8'11") (10'2") (1'8") (7'10") (28") (10'2") (7'2") 9790 3210 (19'2") 3.05
(32'1") (10'6") (10')
9890 3280 3.5
(32'5") (10'9") (11'6")
11290 3400 2.22
(37'1") (11'2") (7'3")
11180 3410 2.55
3700 4625 1185 3405 2995 3130 500 2590 600 3190 2580** (36'8") (11'2") 6.47 (8'4")
PC300-7
(12'2") (15'2") (3'11") (11'2") (9'10") (10'3") (1'8") (8'6") (24") (10'6") (8'6") 11140 3280 (21'3") 3.185
(36'7") (10'9") (10'5")
11170 3760 4.02
(36'8") (12'4") (13'2")
2A-31
AH_25.book Page 32 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
11290 3400 2.2
(37'1") (11'2") (7'3")
11180 3410 2.55
PC300-7*4 3700 4625 1185 3405 2995 3130 500 2590 600 3190 2580** (36'8") (11'2") 6.47 (8'4")
PC360-7*4 (12'2") (15'2") (3'11") (11'2") (9'10") (10'3") (1'8") (8'6") (24") (10'6") (8'6") 11140 3280 (21'3") 3.185
(36'7") (10'9") (10'5")
11170 3760 4.02
(36'8") (12'4") (13'2")
3700 4625 1185 3405 2995 3130 500 2590 800 3390 2580** 11290 3400 6.47 2.2
PC300SE-7***
(12'2") (15'2") (3'11") (11'2") (9'10") (10'3") (1'8") (8'6") (31'5") (11'3") (8'6") (37'1") (11'2") (21'3") (7'3")
3070 11140 3280 3.185
4020 5026 1420 3404 2997 3365 706 2870 800 (10'1") 2591** (36'7") (10'9") 6.47 (10'5")
PC300HD-7
(13'3") (16'6") (4'8") (11'2") (9'10") (11'0") (2'4") (9'5") (31.5") 3570*** (8'6") 11170 3610 (21'3") 4.02
(11'9") (36'8") (11'10") (13'2")
11290 3400 2.22
(37'1") (11'2") (7'3")
11180 3410 2.55
4030 4955 1185 3405 2995 3130 500 2590 700 3290 2580** (36'8") (11'2") 6.47 (8'4")
PC300LC-7
(13'3") (16'3") (3'11") (11'2") (9'10") (10'3") (1'8") (8'6") (24") (10'10") (8'6") 11140 3280 (21'3") 3.185
(36'7") (10'9") (10'5")
11170 3760 4.02
(36'8") (12'4") (13'2")
11140 3280 3.185
4039 4953 1194 3404 2997 3023 508 2580 800 3380 2591** (36'7") (10'9") 6.47 (10'5")
PC300LC-7*
(13'3") (16'3") (3'11") (11'2") (9'10") (10'3") (1'8") (8'6") (31.5") (11'1") (8'6") 11170 3760 (21'3") 4.02
(36'8") (12'4") (13'2")
9545 3210 3.045
(31'4") (10'6") (10'0")
4030 4955 1185 1830 3080 3140 492 2740 850 3590 2565 9570 3280 5.85 3.5
PC308USLC-3* 6
(13'2") (16'3") (3'10") (6'0") (10'1") (10'4") (1'7") (8'11") (33'5") (11'9") (8'5") (31'4") (10'9") (19'2") (11'6")
9500 3535 4.2
(31'2") (11'7") (13'9")
3700 4625 1185 3405 3145 3130 500 2590 600 3190 2580** 11140 3280 6.47 3.185
PC350-7
(12'2") (15'2") (3'11") (11'2") (10'4") (10'3") (1'8") (8'6") (24") (10'6") (8'6") (36'7") (10'9") (21'3") (10'5")
4030 4955 1185 3405 3145 3130 500 2590 600 3190 2580** 11140 3280 6.47 3.185
PC350LC-7
(13'3") (16'3") (3'11") (11'2") (10'4") (10'3") (1'8") (8'6") (24") (10'6") (8'6") (36'7") (10'9") (21'3") (10'5")
11290 3400 2.2
(37'1") (11'2") (7'3")
11180 3410 2.55
4030 4955 1186 3405 2995 3130 498 2590 700 3290 2580** (36'8") (11'2") 6.47 (8'4")
PC340LC-7
(13'3") (16'3") (3'11") (10'9") (9'10") (10'3") (1'7") (8'6") (28") (10'10") (8'6") 11140 3280 (21'3") 3.2
(36'7") (10'9") (10'6")
11170 3760 4.0
(36'8") (12'4") (13'1")
11290 3400 2.2
(37'1") (11'2") (7'3")
11180 3410 2.55
4030 4955 1186 3405 2995 3130 498 2390 600 2990 2580** (36'8") (11'2") 6.47 (8'4")
PC340NLC-7
(13'3") (15'11") (3'11") (10'9") (9'10") (10'3") (1'7") (7'10") (24") (9'10") (8'6") 11140 3280 (21'3") 3.2
(36'7") (10'9") (10'6")
11170 3760 4.0
(36'8") (12'4") (13'1")
11290 3400 2.2
(37'1") (11'2") (7'3")
3570 11180 3410 2.55
4350 5356 1320 3405 2995 3265 706 2870 700 (11'9") 2715 (36'8") (11'2") 6.47 (8'4")
PC380LC-7
(14'3") (17'7") (4'3") (11'2") (9'9") (10'5") (2'4") (9'5") (28") 3072*5 (8'11") 11140 3280 (21'3") 3.19
(10'1") (36'7") (10'8") (10'6")
11170 3760 4.02
(36'8") (12'4") (13'2")
* USA source
** Top of engine cover
*** USA source with variable gauge
*4 China source
*5 Transport dimensions
*6 For USA
2A-32
AH_25.book Page 33 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
11905 3850 2.4
(39'1") (12'8") (7'10")
11995 3745 2.9
4020 5025 1320 3605 2995 3265 555 2740 600 3340 2715 (39'4") (12'3") 7.06 (9'6")
PC400-7
(13'2") (16'6") (4'4") (11'10") (9'10") (10'9") (1'10") (9') (24") (11') (8'11") 11940 3635 (23'2") 3.38
(39'2") (11'11") (11'1")
11950 3885 4.0
(39'2") (12'9") (13'1")
11915 3715 2.4
(39'1") (12'2") (7'10")
11885 3730 2.9
(39') (12'3") (9'6")
4020 5025 1320 3500 2995 3265 555 2740 600 3340 2365 11835 3635 7.06 3.38
PC400-6*4 (13'2") (16'6") (4'4") (11'6") (9'10") (10'9") (1'10") (9') (24") (11') (7'9") (38'10") (11'11") (23'2") (11'1")
11850 3795 4.0
(38'11") (12'5") (13'1")
11685 4385 4.8
(38'4") (14'5") (15'9")
4020 5025 1320 3500 2995 3255 555 2740 600 3340 2365 8424 3485 7.06 2.4
PC400SE-6
(13'2") (16'6") (4'4") (11'6") (9'10") (10'9") (1'10") (9') (24") (11') (7'9") (27'7") (11'5") (23'2") (7'10")
11905 3850 2.4
(39'1") (12'8") (7'10")
11995 3745 2.9
4350 5355 1320 3605 2995 3265 550 2740 700 3440 2715** (39'4") (12'3") 7.06 (9'6")
PC400LC-7 (14'3") (17'7") (4'4") (11'10") (9'10") (10'9") (1'10") (9') (28") (11'3") (8'11") (23'2")
11940 3635 3.38
(39'2") (11'11") (11'1")
11950 3885 4.0
(39'2") (12'9") (13'1")
11905 3850 2.4
(39'1") (12'8") (7'10")
11995 3745 2.9
(39'4") (12'3") (9'6")
4350 5355 1320 3605 2995 3265 550 2740 800 3540 2715 11940 3635 7.06 3.38
PC400LC-7*
(14'3") (17'7") (4'4") (11'10") (9'10") (10'9") (1'10") (9') (32") (11'7") (8'11") (39'2") (11'11") (23'2") (11'1")
11950 3885 4.0
(38'10") (12'5") (13'1")
11830 4435 4.8
(38'10") (14'7") (15'9")
11905 3850 2.4
(39'1") (12'8") (7'10")
11995 3745 2.9
3190*5 (39'4") (12'3") (9'6")
4350 5355 1320 3605 2995 3265 550 2740 800 (10'6") 2715 11940 3635 7.06 3.38
PC400LC-7*** 3690*6
(14'3") (17'7") (4'4") (11'6") (9'10") (10'6") (1'10") (9') (32") (8'11") (39'2") (11'11") (23'2") (11'1")
(12'1") 11950 3885 4.0
(38'10") (12'5") (13'1")
11830 4435 4.8
(38'10") (14'7") (15'9")
* USA source
** Top of engine cover
*** USA source with variable gauge
*4 China source
*5 Crawler retracted
*6 Crawler extended
2A-33
AH_25.book Page 34 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
4020 5025 1320 3605 3145 3265 555 2740 600 3340 2715*4 12040 3660 7.06 3.38
PC450-7
(13'2") (16'6") (4'4") (11'10") (10'4") (10'9") (1'10") (9') (24") (11') (8'11") (39'6") (12'0") (23'2") (11'1")
4350 5355 1320 3605 3145 3265 550 2740 600 3340 2715*4 12040 3660 7.06 3.38
PC450LC-7 (14'3") (16'6") (4'4") (11'10") (9'10") (10'9") (1'10") (9') (24") (11') (8'11") (39'6") (12'0") (23'2") (11'1")
11905 3850 2.4
(39'1") (12'8") (7'10")
11995 3745 2.9
3490 (39'4") (12'3") (9'6")
4
4020 5025 1320 3605 2995 3265 685 2890 600 (11'5") 2715* 11940 3635 7.06 3.4
PC450-7**
(13'2") (16'6") (4'4") (11'10") (9'10") (10'9") (2'3") (9'6") (24") 2990*5 (8'11") (38'10") (11'11") (23'2") (13'1")
(9'10") 11950 3885 4.0
(39'2") (12'9") (13'1")
11830 4435 4.8
(38'10") (14'7") (15'9")
11905 3850 2.4
(39'1") (12'8") (7'10")
11995 3745 2.9
3490 (39'4") (12'3") (9'6")
4350 5355 1320 3605 2995 3265 685 2890 600 (11'5") 2715*4 11940 3635 7.06 3.4
PC450LC-7**
(14'3") (17'7") (4'4") (11'10") (9'10") (10'9") (2'3") (9'6") (24") 2990*5 (8'11") (38'10") (11'11") (23'2") (13'1")
(9'10") 11950 3885 4.0
(39'2") (12'9") (13'1")
11830 4435 4.8
(38'10") (14'7") (15'9")
11830 4600 6.6 2.9
(38'10") (15'1") (21'8") (9'6")
12440 4280 7.3 3.5
(40'10") (14'1") (23'11") (11'6")
4 12810
PC600-7 4250 5340 1365 3675 3195 3290 780 3300 600 3900 3070* 4300 3.5
(13'11") (17'6") (4'6") (12'1") (10'6") (10'10") (2'7") (10'10") (23.6") (12'10") (10'1") (42'0") (14'1") (11'6")
12730 4655 7.66 4.3
(41'9") (15'3") (25'2") (14'1")
12435 5235 5.2
(40'10") (17'2") (17'1")
11830 4600 6.6 2.9
(38'10") (15'1") (21'8") (9'6")
12440 4280 7.3 3.5
(40'10") (14'1") (23'11") (11'6")
4 12810
4600 5690 1365 3675 3195 3290 780 3300 600 3900 3070* 4300 3.5
PC600LC-7 (15'1") (18'8") (4'6") (12'1") (10'6") (10'10") (2'7") (10'10") (23.6") (12'10") (10'1") (42'0") (14'1") (11'6")
12730 4655 7.66 4.3
(41'9") (15'3") (25'2") (14'1")
12435 5235 5.2
(40'10") (17'2") (17'1")
2.9
4600 5690 1365 3675 3195 3310 780 3300 600 3900 2960 7.66 (9'6")
PC600LC-6*
(15'1") (18'8") (4'6") (12'1") (10'6") (10'10") (2'7") (10'10") (23.6") (8'10") (8'10")
12810 4300 (25'2") 3.5
(42'0") (14'1") (11'6")
PC600-6 4250 5340 1365 3675 3195 3310 780 3300 600 3900 2690 12440 4280 7.3 3.5
QUARRY* (13'11") (17'6") (4'6") (12'1") (10'6") (10'10") (2'7") (10'10") (23.6") (12'10") (8'10") (40'10") (14'1") (23'11") (11'6")
11390 4500 6.6 2.9
4250 5340 1365 3675 3195 3310 780 3300 600 3900 2690 (39'2") (14'9") (21'8") (9'6")
PC600SE-6 (13'11") (17'6") (4'6") (12'1") (10'6") (10'10") (2'7") (10'10") (23.6") (12'10") (8'10") 11830 4600 6.6 2.9
(38'10") (15'1") (21.'8") (11'6")
* UK source
** UK source with variable gauge
*4 Top of engine cover
*5 When retracted
2A-34
AH_25.book Page 35 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
E M
D
F N
K
C
G G.L.
I
H A
J B FVBH0313
Boom Arm
A B C D E F G H I J K M N
length length
mm mm mm mm mm mm mm mm mm mm mm mm mm
m m
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) (ft.in)
(ft.in) (ft.in)
14305 4660 3.6
4110 (46'11") (15'3") (11'10")
4500 5810 1560 4245 3195 3560 840 3500 610 (12'10") 3445*5 13955 5970 8.2 4.6
PC750-7 (14'9") (19'1") (5'1") (13'11") (10'6") (11'8") (2'9") (11'6") (24") 3390*4 (11'4") (45'9") (19'7") (26'11") (15'1")
(11'1") 13530 6560 5.6
(44'5") (21'6") (18'4")
14100 4785 3.6
(46'3") (15'8") (11'10")
13955 5970 8.2 4.6
4521 (45'9") (19'7") (26'11") (15'11")
5
5020 6330 1555 4245 3195 3515 840 3500 810 (14'10") 3445* 13530 6560 5.6
PC750LC-7**
(16'6") (20'9") (5'1") (13'11") (10'6") (11'6") (2'9") (11'6") (32") 3990*4 (11'4") (44'5") (21'6") (18'4")
(11'1") 16045 15785 4.6
(52'7") (51'9") 10.0 (15'1")
5625 6090 (32'10") 5.6
(18'5") (19'11") (18'4")
4110
4500 5810 1560 4245 3195 3640 840 3500 610 (13'6") 3445*5 4850 8.04 3.6
PC800-7
(14'9") (19'1") (5'1") (13'11") (10'6") (11'11") (2'9") (11'6") (24") 3390*4 (11'4") (15'11") (26'5") (11'10")
(11'1")
4110
PC750SE-7 4500 5810 1560 4245 3195 3640 840 3500 610 (13'6") 3445*5 13030 4615 7.1 2.9
PC800SE-7 (14'9") (19'1") (5'1") (13'11") (10'6") (11'11") (2'9") (11'6") (24") 3390*4 (11'4") (42'9") (15'2") (23'4") (9'8")
(11'1")
12870 4705 7.1 2.92
4500 5810 1555 4205 3195 3515 840 3500 610 4110 2965 (42'3") (15'5") (23'4") (9'7")
PC750SE-6*
(14'9") (19'1") (5'1") (13'10") (10'6") (11'6") (2'9") (11'6") (24") (13'6") (9'9") 13820 4785 8.2 3.6
(45'4") (15'8") (26'11") (11'10")
16020 6040 3.4
(52'7") (19'10") (11'2")
4995 6425 1790 4810 3470 4120 990 3900 700 4965*** 3925 16050 6500 9.1 4.5
PC1250-7
(16'5") (21'1") (5'10") (15'9") (11'5") (13'6") (3'3") (12'10") (28") (16'3") (12'11") (52'8") (21'4") (29'10") (14'9")
15840 6990 5.7
(52') (22'11") (18'8")
16020 6040 3.4
(52'7") (19'10") (11'2")
5970 7400 1790 4810 3470 4120 990 3900 1000 5265*** 3925 16050 6500 9.1 4.5
PC1250LC-7
(19'7") (24'3") (5'10") (15'9") (11'5") (13'6") (3'3") (12'10") (40") (17'3") (12'11") (52'8") (21'4") (29'10") (14'9")
15840 6040 5.7
(52') (22'11") (18'8")
4995 6425 1790 4810 3470 4120 990 3900 700 4965*** 3925 14790 6265 7.8 3.4
PC1250SP-7
(16'5") (21'1") (5'10") (15'9") (11'5") (13'6") (3'3") (12'10") (28") (16'3") (12'11") (48'6") (20'7") (25'7") (11'2")
17185 6745 8.7 3.9
(56'5") (22'2") (28'7") (12'10")
5780 7445 2080 6140 5055 6510 730 4600 810 5410 4535 17470 6850 9.1 4.1
PC1800-6 (19') (24'5") (6'10") (20'2") (16'7") (21'4") (2'5") (15'1") (32") (17'9") (14'11") (57'4") (22'6") (29'10") (13'5")
19400 7705 11.4 5.0
(63'8") (25'3") (37'5") (16'5")
* UK source
** For USA
*** Include step
*4 When retracted
*5 Top of engine cover
2A-35
AH_25.book Page 36 Tuesday, March 23, 2004 9:41 AM
Dimensions EXCAVATORS
(BACKHOE)
L M
E D
N
F
K
C
G G.L
I A
H B FVBH0251
J
A B C D E F G H I J K L M N Boom Arm
mm mm mm mm mm mm mm mm mm mm mm mm mm mm length length
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) m (ft.in) m (ft.in)
4870 6405 1900 4805 4795 6246 777 4250 600 5050 3900 5750 14500 7800 8.0 3.6
PC1400-1 (16'0") (21'0") (6'3") (15'9") (15'9") (20'6") (2'7") (13'11") (24") (16'7") (12'10") (18'10") (47'7") (25'7") (26'3") (11'0")
PC3000-1 6000 7905 2710 5950 5910 7950 908 4800 800 5600 5280 6290 16100 9200 8.6 4.0
(19'8") (25'11") (8'11") (19'6") (19'5") (26'1) (3'0") (15'9") (31.5") (18'4") (17'4") (20'8") (52'10") (30'2") (28'3") (13'1")
6245 8375 2942 6090 7067 8260 980 5350 1200 6550 6027 7650 18000 10000 9.75 4.5
PC4000-6 (20'6") (27'6") (9'8") (20'0") (23'2") (27'1") (3'3") (17'7") (47") (21'7") (19'9") (25'1") (59'1") (32'10") (32'0") (14'9")
PC5500-6 6800 9100 3240 7260 7270 8535 970 5800 1350 7150 6340 8000 19500 11000 10.0 5.1
(22'4") (29'10") (10'8") (23'10") (23'10") (28'0") (3'2") (19') (53") (23'6") (20'10") (26'3") (64'0") (36'1") (32'10") (16'9")
7945 10580 3470 8410 8300 9480 1144 6650 1500 8150 7030 9400 22900 12800 11.5 5.5
PC8000-6
(26'0") (34'9") (11'5") (27'7") (27'3") (31'1") (3'9") (21'10") (59") (26'9") (23'1") (30'10") (75'2") (42'0") (37'9") (18'1")
2A-36
AH_25.book Page 37 Tuesday, March 23, 2004 9:41 AM
A
B
D F
C G
FVBH0016
* ISO rating
*** For USA
2A-37
AH_25.book Page 38 Tuesday, March 23, 2004 9:41 AM
A
B
* Using power max. function, except PC75R-2, PC95R-2 and EXCEL models, SAE rating
** With one piece boom
*** ISO rating
*4 UK source
*5 For USA
2A-38
AH_25.book Page 39 Tuesday, March 23, 2004 9:41 AM
A
B
* Using power max. function, except PC75R-2, PC95R-2 models, SAE rating
** Optional bucket cylinder is required
*** ISO rating
*4 UK source
*5 For USA
*6 USA source
*7 China source
2A-39
AH_25.book Page 40 Tuesday, March 23, 2004 9:41 AM
A
B
2A-40
AH_25.book Page 41 Tuesday, March 23, 2004 9:41 AM
A
B
2A-41
AH_25.book Page 42 Tuesday, March 23, 2004 9:41 AM
A
B
2A-42
AH_25.book Page 43 Tuesday, March 23, 2004 9:41 AM
A
B
* SAE rating
2A-43
AH_25.book Page 44 Tuesday, March 23, 2004 9:41 AM
8 ft SKZALLG_23
* DIN rating
2A-44
AH_25.book Page 45 Tuesday, March 23, 2004 9:41 AM
Base machine Boom with arm cylinder Arm with bucket cylinder
B A
Boom cylinder
A B
A
FVBH0173
Model PC130-6
PC120-6 PC128US-2 PC130-6*
Item MIGHTY
STD 9560 (21,080) 10820 (23,850) 10360 (22,840) 10000 (22,050)
Basic machine Weight L kg (lb) — — — —
LC 10460 (23060) — — —
A mm (ft.in) 4740 (15'7") 4740 (15'7") 4738 (15'7") 4740 (15'7")
Boom with arm
B mm (ft.in) 1345 (4'5") 1345 (4'5") 1310 (4'4") 1345 (4'5")
cylinder
Weight kg (lb) 930 (2,050) 930 (2,050) 1060 (2,330) 930 (2,050)
Arm size m (ft.in) 2.1 (6'11") 2.1 (6'11") 2.1 (6'11") 2.5 (8'2")
A mm (ft.in) 2845 (9'4") 2845 (9'4") 2860 (9'4") 3260 (10'8")
B mm (ft.in) 645 (2'1") 645 (2'1") 635 (2'1") 590 (1'11")
Weight kg (lb) 510 (1120) 510 (1,120) 440 (970) 640 (1,410)
Arm size m (ft.in) 2.5 (8'2") 2.5 (8'2") 2.5 (8'2") —
A mm (ft.in) 3260 (10'8") 3270 (10'9") 3270 (10'9") —
B mm (ft.in) 590 (1'11") 575 (1'11") 575 (1'11") —
Arm with bucket Weight kg (lb) 540 (1,190) 540 (1,190) 460 (1,020) —
cylinder and linkage Arm size m (ft.in) 3.0 (9'10") 3.0 (9'10") 2.9 (9'6") —
A mm (ft.in) 3750 (12'4") 3750 (12'4") 3770 (12'4") —
B mm (ft.in) 595 (1'11") 595 (1'11") 640 (2'1") —
Weight kg (lb) 660 (1,460) 660 (1,460) 610 (1,350) —
Arm size m (ft.in) — — — —
A mm (ft.in) — — — —
B mm (ft.in) — — — —
Weight kg (lb) — — — —
A mm (ft.in) 1625 (5'4") 1625 (5'4") 1400 (4'7") 1625 (5'4")
Boom cylinder
B mm (ft.in) 166 (6.5") 166 (6.5") 170 (6.7") 166 (6.5")
(Total weight)
Weight kg (lb) 116 × 2 (256 × 2) 116 × 2 (256 × 2) 80 × 2 (176 × 2) 116 × 2 (256 × 2)
Backhoe bucket See bucket arm combination
Model
PC200-7 PC220-7 PC228US-3 PC240-7
Item
STD 15720 (34,660) 18250 (40,230) 18210 (40,150) 18700 (41,230)
Basic machine Weight LC kg (lb) 17120 (37,740) 19680 (43,390) 19510 (43,010) 19800 (43,650)
NLC — — — 19400 (42,770)
A mm (ft.in) 5900 (19'4") 6045 (19'10") 5875 (19'3") 6040 (19'10")
Boom with arm
B mm (ft.in) 1530 (5'0") 1615 (5'4") 1450 (4'9") 1555 (5'1")
cylinder
Weight kg (lb) 1410 (3,130) 1830 (4,030) 1720 (3,790) 2060 (4,540)
Arm size m (ft.in) 1.84 (6'0") 2.0 (6'7") 2.93 (9'7") 2.0 (6'7")
A mm (ft.in) 2775 (9'1") 3065 (10'1") 3905 (12'10") 3050 (10')
B mm (ft.in) 875 (2'10") 975 (3'2") 725 (2'5") 920 (3')
Weight kg (lb) 911 (2,010) 1205 (2,660) 950 (2,090) 1140 (2,510)
Arm size m (ft.in) 2.41 (7'11") 2.5 (8'2") — 2.5 (8'2")
A mm (ft.in) 3430 (11'3") 3625 (11'11") — 3600 (11'10")
B mm (ft.in) 890 (2'11") 925 (3'0") — 860 (2'10")
Arm with bucket Weight kg (lb) 930 (2,050) 1235 (2,720) — 1020 (2,250)
cylinder and linkage Arm size m (ft.in) 2.93 (9'7") 3.05 (10'0") — 3.05 (10')
A mm (ft.in) 3925 (12'11") 4135 (13'7") — 4105 (13'6")
B mm (ft.in) 770 (2'6") 815 (2'8") — 770 (2'6")
Weight kg (lb) 955 (2,110) 1215 (2,680) — 1125 (2,480)
Arm size m (ft.in) — — — 3.5 (11'6")
A mm (ft.in) — — — 4560 (15')
B mm (ft.in) — — — 790 (2'7")
Weight kg (lb) — — — 1240 (2,730)
A mm (ft.in) 2005 (6'7") 2015 (6'7") 2005 (6'7") 2040 (6'8")
Boom cylinder
B mm (ft.in) 337 (743)** 340 (1'1")** 250 (9.8") 280 (11")
(Total weight)
Weight kg (lb) 200 × 2 (440 × 2) 180 × 2 (410 × 2) 253 × 2 (560 × 2)
Backhoe bucket See bucket arm combination
* UK source
** With piping
2A-45
AH_25.book Page 46 Tuesday, March 23, 2004 9:41 AM
Base machine Boom with arm cylinder Arm with bucket cylinder
B A
Boom cylinder
A B
A
FVBH0173
Model
PC300-7 PC350-7
Item
STD 24600 (54,230) 25550 (56,330)
Basic machine Weight LC kg (lb) 25700 (56,660) 26650 (58,750)
NLC — —
A mm (ft.in) 6715 (22'0") 6715 (22'0")
Boom with arm
B mm (ft.in) 1625 (5'4") 1625 (5'4")
cylinder
Weight kg (lb) 2510 (5,530) 2510 (5,530)
Arm size m (ft.in) 2.22 (7'3") 3.2 (10'6")
A mm (ft.in) 3455 (11'4") 4380 (14'4")
B mm (ft.in) 1150 (3'9") 990 (3'3")
Weight kg (lb) 1705 (3,760) 1805 (3,980)
Arm size m (ft.in) 2.55 (8'4") —
A mm (ft.in) 3735 (12'3") —
B mm (ft.in) 1040 (3'5") —
Arm with bucket Weight kg (lb) 1650 (3,640) —
cylinder and linkage Arm size m (ft.in) 3.2 (10'6") —
A mm (ft.in) 4380 (14'4") —
B mm (ft.in) 955 (3'2") —
Weight kg (lb) 1700 (3,750) —
Arm size m (ft.in) 4.02 (13'2") —
A mm (ft.in) 5205 (17'1") —
B mm (ft.in) 945 (3'1") —
Weight kg (lb) 1980 (4,365) —
A mm (ft.in) 2215 (7'3") 2215 (7'3")
Boom cylinder
B mm (ft.in) 405 (1'4")** 405 (1'4")**
(Total weight)
Weight kg (lb) 225 × 2 (496 × 2) 225 × 2 (496 × 2)
Backhoe bucket See bucket arm combination
Model
PC400-7 PC450-7* PC450-7
Item
STD 33160 (73,100) 33920 (74,780) 33620 (74,120)
Basic machine Weight LC kg (lb) 34810 (76,740) 34620 (76,320) 34620 (76,320)
NLC — — —
A mm (ft.in) 7290 (23'11") 7290 (23'11") 7290 (23'11")
Boom with arm
B mm (ft.in) 1695 (5'7") 1615 (5'4") 1695 (5'7")
cylinder
Weight kg (lb) 4000 (8,820) 3810 (8,400) 4200 (9,260)
Arm size m (ft.in) 2.4 (7'10") 2.4 (7'10") 3.38 (11'1")
A mm (ft.in) 3705 (12'2") 3702 (12'2") 4705 (15'5")
B mm (ft.in) 1080 (3'7") 1078 (3'6") 1055 (3'6")
Weight kg (lb) 2030 (4,480) 2030 (4,480) 2400 (5,290)
Arm size m (ft.in) 2.9 (9'6") 2.9 (9'6") —
A mm (ft.in) 4215 (13'10") 4210 (13'10") —
B mm (ft.in) 995 (3'4") 994 (3'4") —
Weight kg (lb) 2150 (4,740) 2140 (4,720) —
Arm size m (ft.in) 3.38 (11'1") 3.38 (11'1") —
Arm with bucket A mm (ft.in) 4615 (15'2") 4600 (15'1") —
cylinder and linkage B mm (ft.in) 975 (3'2") 975 (3'2") —
Weight kg (lb) 2200 (4,850) 2120 (4,670) —
Arm size m (ft.in) 4.0 (13'1") 4.0 (13'1") —
A mm (ft.in) 5235 (17'2") 5234 (17'2") —
B mm (ft.in) 965 (3'2") 963 (3'2") —
Weight kg (lb) 2440 (5,380) 2460 (5,420) —
m (ft.in) — 4.8 (15'9") —
A
mm (ft.in) — 6036 (19'10") —
B
mm (ft.in) — 1041 (3'5") —
Weight
kg (lb) — 2580 (5,690) —
A mm (ft.in) 2445 (8'1") 2445 (8'1") 2445 (8'1")
Boom cylinder
B mm (ft.in) 225 (8.9") 237 (9.3") 225 (8.9")
(Total weight)
Weight kg (lb) 400 x 2 (880 x 2) 390 × 2 (860 × 2) 400 × 2 (880 × 2)
Backhoe bucket See bucket arm combination
* UK source
** With piping
2A-46
AH_25.book Page 47 Tuesday, March 23, 2004 9:41 AM
Boom
Arm
FVPM3163
(4) Others
")
2'3
Bucket Boom & arm cylinder 0(
68 31
95
(10
'6"
)
1330 (4'4")
FVPM3164
1 1
19 23 ")
2500 (8'2")
")
Three-part transportation
(1) Work equipment assembly (3) Others
2A-47
AH_25.book Page 48 Tuesday, March 23, 2004 9:41 AM
Arm
Overall
mm (fi.in) 1210 (4'0") 1240 (4'1") 1210 (4'0") 1430 (4'8")
height
(1)
ton (US.
Weight 3.2 (3.5) 3.3 (3.6) 3.2 (3.5) 3.4 (3.7)
ton)
Overall
mm (fi.in) 2040 (6'8") 2040 (6'8") 2040 (6'8") 2260 (7'5")
length
Overall
mm (fi.in) 1790 (5'10") 1870 (6'2") 1790 (5'10") 2120 (6'11")
Bucket width
Overall
mm (fi.in) 1870 (6'2") 1880 (6'2") 1870 (6'2") 1800 (5'11")
height
Weight ton (US. ton) 2.5 (2.8) 3.0 (3.3) 2.5 (2.8) 3.4 (3.7)
Overall
mm (fi.in) 3110 (10'2") 3110 (10'2") 3110 (10'2") 3110 (10'2")
length
Four-part
Cylinder
ton (US.
Weight 1.8 (2.0) 1.8 (2.0) 1.8 (2.0) 1.8 (2.0)
ton)
Overall
mm (fi.in) 4970 (16'4") 4970 (16'4") 4970 (16'4") 4970 (16'4")
length
Overall
mm (fi.in) 3195 (10'6") 3195 (10'6") 3195 (10'6") 3195 (10'6")
width
(2) Upper Structure
Overall
mm (fi.in) 2500 (8'2") 2500 (8'2") 2500 (8'2") 2500 (8'2")
height
ton (US.
Weight 16.8 (18.5) 16.9 (18.6) 16.8 (18.5) 16.8 (18.5)
ton)
Overall
mm (fi.in) 5340 (17'6") 5370 (17'7") 5690 (18'8") 5340 (17'6")
length
Overall
mm (fi.in) 875 (2'11") 875 (2'11") 875 (2'11") 875 (2'11")
width
(3) Undercarriage
Overall
mm (fi.in) 1260 (4'2") 1290 (4'3") 1260 (4'2") 1260 (4'2")
height
ton (US.
Weight 16.4 (18.1) 17.4 (19.2) 17.4 (19.2) 16.4 (18.1)
ton)
Overall
mm (fi.in) 3195 (10'6") 3195 (10'6") 3195 (10'6") 3195 (10'6")
length
Overall
mm (fi.in) 680 (2'3") 680 (2'3") 680 (2'3") 680 (2'3")
Others width
(4)
(Counterweight) Overall
mm (fi.in) 1330 (4'4") 1330 (4'4") 1330 (4'4") 1330 (4'4")
height
ton (US.
Weight 10.75 (11.8) 10.75 (11.8) 10.75 (11.8) 10.75 (11.8)
ton)
(1) Work Equipment The same as four-part transportation
Overall
mm (fi.in) 6170 (20'3") 6180 (20'4") 6340 (20'10") 6170 (20'3")
length
Overall
mm (fi.in) 3195 (10'6") 3195 (10'6") 3195 (10'6") 3195 (10'6")
Three-part
width
(2) Base Machine
Overall
mm (fi.in) 3330 (10'11") 3340 (11'0") 3330 (10'11") 3330 (10'11")
height
ton (US.
Weight 33.2 (36.6) 34.3 (37.8) 34.2 (37.7) 33.2 (36.6)
ton)
Others
(3) The same as four-part transportation
(Counterweight)
2A-48
AH_25.book Page 49 Tuesday, March 23, 2004 9:41 AM
Boom
5810 (19'1")
FVPM3076
FVPM3075
(4) Others
Arm 319
980 5 (1
(3'3 830 ") 0'6
")
FVPM2405 ") 9
OPG (2'
(1'7")
470
")
6'0
(3'7")
1090
16 ")
(5' 00 2.8
(2) Upper structure 3") 70(
500
500
5970 (19'7") ") 6") (1'
0(
6'3 (1' 10' 8")
8") 0(
190 320
(*2840 (9'4"))
2730 (8'11")
FVPM3065
OPG (PC800/SE only) FVPM3066
Three-part transportation
(1) Work equipment assembly (3) Others
6840 (22'5")
FVPM3067
2A-49
AH_25.book Page 50 Tuesday, March 23, 2004 9:41 AM
2A-50
AH_25.book Page 51 Tuesday, March 23, 2004 9:41 AM
Boom
2510(8'3")
FVBH0178
Arm
3. Undercarriage
6425(21'2") 1222(4')
PC1250:5.9t 4895x1626x890 LC:1295(4'3")
(6.5USt) (16'1")x(5'4")x(2'11") LC:7400(24'3")
PC1250SP:6.3t 4914x1683x890
LC:1640(5'5")
Bucket
Weight
PC1250:30.0t (33.1USt)
15.0t x2(16.5x2USt)
PC1250:4.3t 2700x2100x2050 PC1250SP:30.9t(34.1USt)*
(4.7USt) (8'10")x(6'11")x(6'9")
15.45t x2(17.0x2USt)
PC1250SP:5.9t 2527x2420x2520
(6.5USt) (8'3")x(7'11")x(8'3") FVBH0176 PC1250LC:38t (41.9USt)
19t x2(20.9x2USt)
FVBH0179
Arm cylinder * With full length roller guard
1.5t (1.7USt)
Boom cylinder
2.4t [1.2tx2]
(2.64USt) (1.32UStx2)
FVBH0177
4. Others
27.7t (30.5 US.ton)
2850(9'4") 600(2')
1260(4'2")
400
(1'4")
2850(9'4")
Width:3540 (11'7")
Weight:9.3t (10.3USt)
845
(2'9")
880(2'11") 620
3470(11'5") (2')
3155(10'4")
1810
(5'11")
1830 1760(5'9")
(6')
100(3.9")
18.0t(19.8USt)
FVBH0180
2A-51
AH_25.book Page 52 Tuesday, March 23, 2004 9:41 AM
FVBH0202
2. Arm
FVBH0203
3. Bucket
FVBH0204
4. Upper structure
5. Center frame
6. Left Undercarriage
7. Right Undercarriage
8. Operator cab
9. Counterweight
7.45 (8.2)
2A-52
AH_25.book Page 53 Tuesday, March 23, 2004 9:41 AM
2A-53
AH_25.book Page 54 Tuesday, March 23, 2004 9:41 AM
2A-54
AH_25.book Page 55 Tuesday, March 23, 2004 9:41 AM
2A-55
AH_25.book Page 56 Tuesday, March 23, 2004 9:41 AM
2A-56
AH_25.book Page 57 Tuesday, March 23, 2004 9:41 AM
2A-57
AH_25.book Page 58 Tuesday, March 23, 2004 9:41 AM
Left Crawler Side Frame with 1350 Tracks 9100 2350 2600 70
(29'10") (7'9") (8'6") (77.2)
Stick (5,1 m) with 2 Bucket Cylinders, Linkage 7150 2050 2700 31.9
and Rod (23'6") (6'9") (8'10") (35.2)
2A-58
AH_25.book Page 59 Tuesday, March 23, 2004 9:41 AM
2A-59
AH_25.book Page 60 Tuesday, March 23, 2004 9:41 AM
3 • Road liner (rubber) • The surface of the shoe in • Use in the following places
contact with the ground is will shorten the cutting life
made of rubber, so the of the rubber.
machine can travel on (1) Rocky ground
paved roads without (2) Cold areas
damaging the road (below -25ºC)
surface. (3) Hot areas
• Prevents noise when (above 65ºC)
machine is traveling. • Because there are no
• Rubber pad Paved road grouser, this shoe does not
Indoor work bite into the ground.
2A-60
AH_25.book Page 61 Tuesday, March 23, 2004 9:41 AM
2A-61
AH_25.book Page 62 Tuesday, March 23, 2004 9:41 AM
PC300-7*5
600 (24")* A PC600-6*4 600 (24")* A
Triple-grouser Triple-grouser
700 (28") B PC600SE-6
600 (24") A 610 (24")* A
PC300LC-7 Triple-grouser 700 (28")* B 710 (28") A
Double-
800 (31.5") C PC750-7 810 (32") B
grouser
700 (28") B 910 (36") B
PC300LC-7*** Triple-grouser 800 (31.5")* C 1010 (40") C
850 (33.5") C 810 (32")* B
Double-
700 (28") B PC750LC-7 grouser 1010 (40") B
PC308USLC-3 Triple-grouser 800 (31.5") C 1110 (44") C
850 (33.5")* C 610 (24")* A
600 (24") A 710 (28") A
Double-
700 (28")* B PC750SE-7 810 (32") B
PC340LC-7 Triple-grouser grouser
800 (31.5") C 910 (36") B
850 (33.5") C 1010 (40") C
PC340NLC-7 Triple-grouser 600 (24")* A 610 (24")* A
600 (24") A PC750SE-6*4 Double- 710 (28") A
PC350-7 Triple-grouser grouser
700 (28")* B 810 (32") B
PC360-7*5 Triple-grouser 600 (24")* A Double- 610 (24")* A
PC800-7
600 (24") A grouser 710 (28") A
PC350LC-7 Triple-grouser
700 (28")* B Double- 610 (24")* A
PC800SE-7 grouser
600 (24") A 710 (28") A
PC380LC-7 Triple-grouser 700 (28")* B Double- 700 (28")* A
PC1250-7
800 (31.5") C grouser 1000 (39.4") B
600 (24")* A Double- 1000 (39.4")* B
PC1250LC-7 grouser
PC400-6*5 Triple-grouser 700 (28") B 1200 (47.2") B
800 (31.5") C Double-
PC1250SP-7 grouser 700 (28")* A,B
600 (24")* A
PC400-7 Triple-grouser 700 (28") B Double- 600 (24")* A
PC1400-1
grouser 800 (31.4") B
800 (31.5") C
PC400SE-6 Triple-grouser 800 (31.05") C Double- 810 (32")* A
PC1800-6 grouser
600 (24") A 1010 (40") B
PC400LC-7 Triple-grouser 700 (28")* B Double- 800 (31.4")* A
PC3000-1
grouser 1000 (39.3") B
800 (31.5") C
700 (28")* B Double- 1200 (47.2")* A
PC4000-6 grouser
PC400LC-7*** Triple-grouser 800 (31.5") C 1500 (59") B
900 (35.5") C Double- 1350 (53")* A
PC5500-6
grouser 1800 (71") B
Double- 1500 (59")* A
PC8000-6 grouser 1900 (75") B
* Standard shoe
** See classification of the application
*** USA source
*4 UK source
*5 China source
2A-62
AH_25.book Page 63 Tuesday, March 23, 2004 9:41 AM
NOTE: Select the narrowest possible shoes, depending on the flotation and ground pressure of the
machines. If the shoe is too wide, the load on the track shoe increases and results in bends in the
shoes, cracks in the links, breakage and slipping out of the pins and loosening of the bolts.
2A-63
AH_25.book Page 64 Tuesday, March 23, 2004 9:41 AM
H
H = Track height
L L = Distance between centers of sprocket and front idler
FVBH0003
* Standard shoe
NOTE: The shoe for the long-track excavator (L and LC), wide shoe (excluding the narrowest shoe for a
model) and swamp shoe are provided with low ground pressure. These shoes should be used on soft
and swampy terrain where the standard excavator with standard shoe is not usable due to sinkage of
the tracks. If such shoes are used in swampy fields with stones, stumps and roots, bending of the
shoe plates, cracks in the links, breakage of pins, loosening of shoe bolts and other damage may
result. Therefore, the job site must be studied carefully, to provide the customer with correct
instructions and advice.
2A-64
AH_25.book Page 65 Tuesday, March 23, 2004 9:41 AM
2A-65
AH_25.book Page 66 Tuesday, March 23, 2004 9:41 AM
* Standard shoe
** UK source
*** USA source
*4 China source
NOTE: The shoe for the long-track excavator (L and LC), wide shoe (excluding the narrowest shoe for a
model) and swamp shoe are provided with low ground pressure. These shoes should be used on
soft and swampy terrain where the standard excavator with standard shoe is not usable due to
sinking of the tracks. If such shoes are used in swampy fields with stones, stumps and roots,
bending of the shoe plates, cracks in the links, breakage of pins, loosening of shoe bolts and other
damage may result. Therefore, the job site must be studied carefully, to provide the customer with
correct instructions and advice.
2A-66
AH_25.book Page 67 Tuesday, March 23, 2004 9:41 AM
2A-67
AH_25.book Page 68 Tuesday, March 23, 2004 9:41 AM
* Standard shoe
** UK source
*** USA source
*4 China source
*5 Indonesia source
NOTE: The shoe for the long-track excavator (L and LC) wide shoe (excluding the narrowest shoe for a
model) and swamp shoe are provided with low ground pressure. These shoes should be used on
soft and swampy terrain where the standard excavator with standard shoe is not usable due to
sinking of the tracks. If such shoes are used in swampy fields with stones, stumps and roots,
bending of the shoe plates, cracks in the links, breakage of pins, loosening of shoe bolts and other
damage may result. Therefore, the job site must be studied carefully, to provide the customer with
correct instructions and advice.
2A-68
AH_25.book Page 69 Tuesday, March 23, 2004 9:41 AM
* Standard shoe
** UK source
*** For USA source
NOTE: The shoe for the long-track excavator (L and LC), wide shoe (excluding the narrowest shoe for a
model) and swamp shoe are provided with low ground pressure. These shoes should be used on
soft and swampy terrain where the standard excavator with standard shoe is not usable due to
sinking of the tracks. If such shoes are used in swampy fields with stones, stumps and roots,
bending of the shoe plates, cracks in the links, breakage of pins, loosening of shoe bolts and other
damage may result. Therefore, the job site must be studied carefully, to provide the customer with
correct instructions and advice.
2A-69
AH_25.book Page 70 Tuesday, March 23, 2004 9:41 AM
* Standard shoe
** UK source
*** USA source
NOTE: The shoe for the long-track excavator (L and LC), wide shoe (excluding the narrowest shoe for a
model) and swamp shoe are provided with low ground pressure. These shoes should be used on
soft and swampy terrain where the standard excavator with standard shoe is not usable due to
sinking of the tracks. If such shoes are used in swampy fields with stones, stumps and roots,
bending of the shoe plates, cracks in the links, breakage of pins, loosening of shoe bolts and other
damage may result. Therefore, the job site must be studied carefully, to provide the customer with
correct instructions and advice.
2A-70
AH_25.book Page 71 Tuesday, March 23, 2004 9:41 AM
2A-71
AH_25.book Page 72 Tuesday, March 23, 2004 9:41 AM
Komatsu offers various kinds and sizes of buckets so that the users are able to select the optimum bucket for
the type of soil and the work to be performed. This enables the work to be accomplished most efficiently.
The following is a guide for selecting the optimum bucket.
2. Selection of size
The following two points 1) and 2) should be considered altogether.
1) From the machine stability (For backhoe type)
If the bucket size (capacity) is too big, it will worsen the stability of the machine, resulting in danger of
tipping over or rolling over.
The concept of the bucket selection from the point of machine stability is from the following.
Putting A as the maximum allowable load from over-side (sideways) machine stability and B as the
bucket working load (bucket weight + carrying material weight), the size of the bucket should be
selected so as to be;
B≤A
From Figure 1,
A = W1 + (L0 / L) W2 = W1 + W2 Approximately
where, W1 : The weight of the empty bucket shown in the table of Lift Capacity. The value of the
weight is shown in the tables of "Bucket and Arm Combination".
W2 : The smallest lift capacity in the table of Lift Capacity at respective boom length and
arm length (The lift capacity differs by the arm vertical position)
From Figure 2,
B = W3 + W4
where, W3 : The bucket weight used for the job
W4 : The weight of carried material
(= rated bucket capacity × specific gravity of carried material)
W4
W1
W3
W2
L L
L0
FVBH0239 FVBH0240
Figure 1 Figure 2
2A-72
AH_25.book Page 73 Tuesday, March 23, 2004 9:41 AM
(1)Digging force
Rated digging force of the bucket is the force at the foremost digging point of the bucket. This
digging force is generated by the bucket hydraulic cylinder and the arm hydraulic cylinder. The
former is called the "Bucket digging force" and the latter is called the "Arm crowd force".
These digging forces are calculated by applying working relief hydraulic pressure to the cylinder(s).
The weight of components and friction are to be excluded in the calculation. The definition of the
digging forces are based on SAE J1179 and are as follows.
a. Bucket digging force
The rated bucket digging force (V, in the
top figure) is the force generated by the
bucket cylinder(s) and the tangent to the Bucket cylinder
arc of radius C. The bucket should be
positioned to obtain the maximum output
moment from the bucket cylinder(s) and V V
the connecting linkage. C C
b. Arm crowd force 90
90
The rated arm crowd force (W, in the
bottom figure) is the force generated by
the arm cylinder(s) and the tangent to the Arm cylinder
arc of the radius B. The arm should be 90
positioned to obtain the maximum output
moment from the arm cylinder(s) and the 90
bucket, positioned as mentioned above.
(2)Bucket width
The wider the bucket is, the worse the
bucket penetration is. Generally speaking, a B B
wide bucket is recommended for excavating
soil that can be broken easily. A narrow
bucket is better suited for work on hard soil. W
The width of the bucket must be limited also W
from the point of durability of the bucket, 90 90
arm, boom and their hinge pins and
bushings,. If the width is too great, it will FVBH0018
cause excessive twist on the relevant parts,
resulting in premature breakage or wear.
(3)Tip radius
The tip radius also affects the digging force
of the bucket. If the bucket cylinder is
provided with the same pushing force, the
bucket with the shorter tip radius is better Narrower Wider
able to dig hard soil than the bucket with the Bucket width
longer tip radius.
The bucket width and the tip radius should Shorter Longer
be selected with the combination of the
digging forces mentioned above in order to
have appropriate bucket penetration.
Tip radius
When you need the values for allowable FVBH0045
bucket width and bucket penetration force
for each model, you can request and get the
figures from Komatsu through your
distributor.
2A-73
AH_25.book Page 74 Tuesday, March 23, 2004 9:41 AM
The theory of "BUCKET SELECTION" can be applied when a bucket is procured from a local attachment
manufacturers. But the quality of the bucket from a local supplier can not be guaranteed by Komatsu.
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width Weight
Without side With side kg (lb) Arm length
SAE, PCSA CECE (With side m (ft.in)
cutters cutters
m3 (cu.yd) m3 (cu.yd) cutters)
mm (in) mm (in)
PC01-1 0.48 (1'7") —
0.008 (0.01) 0.007 (0.009) 250 (9.8") 265 (10.4") 7 (15) —
PC09-1 0.684 (2'3") 0.687(2'3") 0.884 (2'11")
0.017 (0.022) — 225 (8.9") 250 (9.8") 11 (24)
0.022 (0.029)* — 325 (12.8") 350 (13.8") 14 (31)
0.025 (0.033) — 375 (14.8") 400 (15.7") 15 (33)
PC12R-8 0.88 (2'11") 1.13 (3'8")
0.03 (0.04) — 250 (9.8") — 20 (44)
0.035(0.046) — 300 (11.8") — 23 (51)
0.04 (0.05)* — 350 (13.8") — 24 (53)
0.05 (0.065) — 400 (15.7") — 25 (55)
0.06 (0.08) — 450 (17.7") — 26 (57)
PC15MRX-1 0.965 (3'2") 1.215 (4'0")
0.022 (0.029) — 300 (11.8") 350 (13.8")
0.04 (0.05) — 350 (13.8") 400 (15.7")
0.044 (0.06) — 400 (15.7") 450 (17.7")
PC15R-8 0.965 (3'2") 1.215 (4'0")
0.03 (0.04) — 250 (9.8") — 20 (44)
0.035(0.046) — 300 (11.8") — 23 (51)
0.04 (0.05)* — 350 (13.8") — 24 (53)
0.05 (0.065) — 400 (15.7") — 25 (55)
0.06 (0.08) — 450 (17.7") — 26 (57)
PC20MRX-1 0.93 (3'1") 1.28 (4'2")
0.033 (0.043) 0.03 (0.04) 250 (9.8") 320 (12.6") 32 (70)
0.044 (0.058) 0.04 (0.05) 350 (13.8") 420 (16.2") 37 (82)
0.066 (0.086) 0.06 (0.08) 430 (16.9") 500 (13.8") 48 (106)
0.08 (0.10) 0.07 (0.09) 530 (20.9") 600 (23.6") 52 (115)
PC20R-8 1.08 (3'7") 1.38 (4'6")
0.035 (0.046) — 320 (12.6") — 32 (70)
0.055 (0.072) — 420 (16.5") — 37 (82)
0.07 (0.09) — 500 (19.7") — 45 (99)
0.085 (0.11) — 600 (23.6") — 52 (115)
PC27MRX-1 1.11 (3'8") 1.41 (4'8")
0.042 (0.055) — 254 (10") — —
0.051 (0.067) — 305 (12") — —
0.08 (0.105) — 430 (17") 500 (19.7") —
0.08 (0.105) — 457 (18") — —
0.09 (0.118) — 530 (21") 600 (23'6") —
PC27R-8 1.2 (3'11") 1.5 (4'11")
0.045 (0.06) — 250 (9.8") — 32 (70)
0.06 (0.08) — 350 (13.5") — 40 (88)
0.075 (0.1)* — 450 (17.7") — 52 (115)
0.095 (0.12) — 600 (23.6") — 60 (132)
0.105 (0.135) — 650 (25.6") — 65 (143)
* Strengthened bucket
** Breaker arm
*** Without side cutters
2A-74
AH_25.book Page 75 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width Weight
Without side With side kg (lb) Arm length
SAE, PCSA CECE (With side m (ft.in)
cutters cutters
m 3 (cu.yd) m (cu.yd)
3
cutters)
mm (in) mm (in)
PC30MR-2 1.26 (4'1") 1.66 (4'4")
0.035 (0.046) 0.03 (0.04) 250 (9.8") 320 (12.6") 50 (110)
0.044 (0.058) 0.04 (0.05) 280 (11.0") 350 (13.8") 52 (115)
0.055 (0.07) 0.05 (0.065) 350 (13.8") 420 (16.5") 58 (129)
0.09 (0.12) 0.08 (0.10) 430 (16.9") 500 (19.7") 63 (139)
0.11 (0.14) 0.10 (0.13) 530 (20.9") 600 (23.6") 81 (178)
PC35MR-2 1.35 (4'5") 1.75 (5'9")
0.055 (0.072) 0.05 (0.065) 350 (13.8") 420 (16.5") 59 (130)
0.09 (0.12) 0.08 (0.10) 430 (16.9") 500 (19.7") 78 (172)
0.11 (0.143) 0.10 (0.13) 530 (20.9") 600 (23.6") 83 (183)
0.13 (0.17) 0.12 (0.16) 630 (24.8") 700 (27.6") 98 (216)
PC35R-8 1.35 (4'5") 1.75 (5'9")
0.05 (0.065) — 300 (11.8") — 55 (121)
0.07 (0.09) — 400 (15.7") — 65 (143)
0.095 (0.12) — 500 (19.7") — 80 (176)
0.12 (0.16) — 600 (23.6") — 90 (198)
0.13 (0.17) — 650 (25.6") — 95 (209)
PC40MR-2 1.44 (4'9") 1.9 (6'3")
0.055 (0.07) 0.05 (0.065) 300 (11.8") 370 (14.6") 89 (196)
0.11 (0.14) 0.10 (0.13) 430 (16.9") 500 (19.7") 94 (207)
0.14 (0.18) 0.13 (0.17) 535 (21.1") 600 (23.6") 105 (231)
0.16 (0.21) 0.12 (0.18) 585 (23.0") 650 (25.6") 121 (267)
PC50MR-2 1.48 (4'10") 2.0 (6'7")
0.055 (0.07) 0.05 (0.065) 300 (11.8") 370 (14.6") 89 (196)
0.11 (0.14) 0.10 (0.13) 430 (16.9") 500 (19.7") 94 (207)
0.16 (0.21) 0.21 (0.18) 585 (23.0") 650 (25.6") 121 (267)
PC45R-8 1.48 (4'10") 1.9 (6'3")
0.07 (0.09) — 300 (11.8") — 75 (165)
0.10 (0.13) — 400 (15.7") — 90 (198)
0.125 (0.16) — 500 (19.7") — 100 (220)
0.150 (0.20) — 600 (23.6") — 115 (254)
0.175 (0.23) — 700 (27.6") — 125 (276)
* Strengthened bucket
*** Without side cutters
2A-75
AH_25.book Page 76 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width
Weight
Without side With side Arm length
SAE, PCSA CECE kg (lb) m (ft.in)
3 3 cutters cutters (With side cutters)
m (cu.yd) m (cu.yd)
mm (in) mm (in)
1.7 2.1
PC75R-2 (5'7") (6'11")
0.086 (0.11) — 300 (11.8") — 128 (282)* —
0.128 (0.17) — 400 (15.7") — 160 (353)* —
0.171 (0.22) — 500 (19.7") — 184 (406)* —
0.2 (0.26) — 600 (23.6") — 174 (384)* —
0.232 (0.30) — 700 (27.6") — 189 (417)* —
0.265 (0.35) — 800 (31.5") — 196 (432)* —
1.65 2.25
PC78US-6 (5'5") (7'5")
0.09 (0.12) 0.08 (0.10) 350 (13.8") 450 (17.7") 148 (330) —
0.12 (0.16) 0.11 (0.14) 450 (17.7") 550 (21.7") 161 (355) —
0.20 (0.26) 0.18 (0.24) 550 (21.7") 650 (25.6") 184 (406) —
0.28 (0.37) 0.25 (0.33) 650 (25.6") 750 (29.5") 212 (467) —
0.34 (0.45) 0.32 (0.42) 725 (28.5") 825 (32.5") 220 (485) —
1.65 2.25
PC78MR-6 (5'5") (7'5")
0.09 (0.12) 0.08 (0.10) 350 (13.8") 450 (17.7") 148 (330) —
0.12 (0.16) 0.11 (0.14) 450 (17.7") 550 (21.7") 161 (355) —
0.20 (0.26) 0.18 (0.24) 550 (21.7") 650 (25.6") 184 (406) —
0.28 (0.37) 0.25 (0.33) 650 (25.6") 750 (29.5") 212 (467) —
0.34 (0.45) 0.32 (0.42) 725 (28.5") 825 (32.5") 220 (485) —
1.6 1.85 2.3
PC95R-2 (5'3") (6'1") (7'7")
0.086 (0.11) — 300 (11.8") — 128 (282)*
0.128 (0.17) — 400 (15.7") — 160 (353)*
0.171 (0.22) — 500 (19.7") — 184 (406)*
0.213 (0.28) — 600 (23.6") — 200 (441)*
0.255 (0.33) — 700 (27.6") — 218 (481)*
0.298 (0.39) — 800 (31.5") — 236 (520)*
0.34 (0.44) — 900 (35.4") — 256 (564)*
1.85 2.0 2.3
PC110R-1 (6'1") (6'7") (7'7")
0.093 (0.12) — 300 (11.8") — 168 (370)*
0.139 (0.18) — 400 (15.7") — 194 (428)*
0.181 (0.24) — 500 (19.7") — 218 (481)*
0.225 (0.29) — 600 (23.6") — 234 (516)*
0.27 (0.35) — 700 (27.6") — 252 (556)*
0.314 (0.41) — 800 (31.5") — 270 (595)*
0.36 (0.47) — 900 (35.4") — 294 (648)*
0.4 (0.52) — 1000 (39.4") — 320 (705)*
2.1 2.50 3.00
PC120-6 (6'11") (8'2") (9'10")
0.18 (0.24) 0.16 (0.21) 450 (17.7") 566 (22.3") 256 (564)
0.28 (0.37) 0.26 (0.34) 600 (23.6") 720 (28.3") 303 (668)
0.36 (0.47) 0.33 (0.43) 700 (27.6") 820 (32.3") 330 (728)
0.50 (0.65) 0.45 (0.59) 859 (33.8") 979 (38.5") 399 (880)
0.60 (0.78) 0.55 (0.72) 1000 (39.4") — 400 (882)*
0.18 (0.24) 0.16 (0.21) 450 (17.7") 566 (22.3") 256 (564)
* Without side cutters For the source of each model, see the tables from 2A-14 to 2A-26.
2A-76
AH_25.book Page 77 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width
Weight Arm length
SAE, PCSA CECE Without side With side kg (lb)
cutters cutters m (ft.in)
m3 (cu.yd) m3 (cu.yd) mm (in) mm (in)
(With side cutters)
* Without side cutters For the source of each model, see the tables from 2A-14 to 2A-26.
** UK source
*** USA source
*4 For USA
2A-77
AH_25.book Page 78 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width
Weight
Without side With side Arm length
SAE, PCSA CECE kg (lb) m (ft.in)
3 3 cutters cutters (With side cutters)
m (cu.yd) m (cu.yd)
mm (in) mm (in)
1.84 2.41 2.93
PC200-7, PC200LC-7 (6') (7'11") (9'7")
0.50 (0.65) 0.45 (0.59) 750 (29.5") 855 (33.7") 478 (1050)
0.80 (1.05) 0.70 (0.92) 1045 (41.1") 1150 (45.3") 645 (1420)
0.93 (1.22) 0.80 (1.05) 1200 (47.2") 1305 (51.4") 696 (1530)
1.05 (1.37) 0.90 (1.18) 1330 (52.4") 1435 (56.5") 757 (1670)
1.17 (1.53) 1.00 (1.31) 1450 (57.1") — 940 (2070)*
1.84 2.41 2.93
PC200-7*5, PC200LC-7*5 (6') (7'11") (9'7")
0.80 (1.05) 0.70 (0.92) 1045 (41.1") 1150 (45.3") 658 (1450)
0.80 (1.05)*4 0.70 (0.92) 1045 (41.1") 1150 (45.3") 783 (1726)
0.90 (1.18) 0.80 (1.05) 1200 (47.2") 1305 (51.4") 728 (1605)
1.0 (1.31) 0.90 (1.18) 1330 (52.4") 1435 (56.5") 772 (1702)
2.41 2.93
PC200-7, PC200LC-7*** (7'11") (9'7")
0.50 (0.66) — 610 (24") — 639 (1409)
0.67 (0.88) — 762 (30") — 679 (1497)
0.86 (1.13) — 914 (36") — 767 (1690)
1.04 (1.36) — 1067 (42") — 842 (1856)
1.22 (1.59) — 1219 (48") — 910 (2007)
1.38 (1.80) — 1372 (54") — 962 (2121)
1.53 (2.0) — 1524 (60") — 1102 (2430)
0.48 (0.63) — 610 (36") — 655 (1445)
0.65 (0.85) — 762 (42") — 717 (1580)
0.83 (1.08) — 914 (48") — 792 (1745)
0.99 (1.30) — 1067 (24") — 895 (1973)
1.16 (1.52) — 1219 (29") — 1036 (2283)
1.8 2.4 2.9
PC210-7** (5'11") (7'10") (9'6")
0.48 (0.63) — 600 (23.6") — 480 (1058)
0.55 (0.72) — 700 (27.6") — 530 (1168)
0.63 (0.82) — 800 (31.5") — 580 (1279)
0.71 (0.93) — 900 (35.4") — 610 (1345)
0.78 (1.02) — 1000 (39.4") — 650 (1433)
0.86 (1.15) — 1100 (43.3") — 700 (1543)
0.96 (1.26) — 1200 (47.2") — 760 (1675)
1.03 (1.35) — 1300 (51.2") — 810 (1786)
1.11 (1.45) — 1400 (55.1") — 870 (1918)
1.19 (1.56) — 1500 (59.1") — 930 (2050)
1.49 (1.95) — 1600 (63.0") — 1100 (2425)
1.58 (2.07) — 1700 (66.9") — 1150 (2535)
1.68 (2.20) — 1800 (70.9") — 1200 (2645)
1.8 2.4 2.9
PC210LC-7**, PC210NLC-7** (5'11") (7'10") (9'6")
0.48 (0.63) — 600 (23.6") — 480 (1058)
0.55 (0.72) — 700 (27.6") — 530 (1168)
0.63 (0.82) — 800 (31.5") — 580 (1279)
0.71 (0.93) — 900 (35.4") — 610 (1345)
0.78 (1.02) — 1000 (39.4") — 650 (1433)
0.86 (1.15) — 1100 (43.3") — 700 (1543)
0.96 (1.26) — 1200 (47.2") — 760 (1675)
1.03 (1.35) — 1300 (51.2") — 810 (1786)
1.11 (1.45) — 1400 (55.1") — 870 (1918) (NLC: )
1.19 (1.56) — 1500 (59.1") — 930 (2050) (NLC: ) (NLC: ) (NLC: )
1.49 (1.95) — 1600 (63.0") — 1100 (2425) (NLC: ) (NLC: ) (NLC: )
1.58 (2.07) — 1700 (66.9") — 1150 (2535) (NLC: )
1.68 (2.20) — 1800 (70.9") — 1200 (2645) (NLC: )
1.84 2.41 2.93
PC210-7*5, PC210LC-7*5 (6') (7'11") (9'7")
0.80 (1.05)*4 0.70 (0.92) 1045 (41.1") 1150 (45.3") 783 (1726)
0.90 (1.18) 0.80 (1.05) 1200 (47.2") 1305 (51.4") 728 (1605)
1.0 (1.31) 0.90 (1.18) 1330 (52.4") 1435 (56.5") 772 (1702)
* Without side cutters For the source of each model, see the tables from 2A-14 to 2A-26.
** UK source
*** USA source
*4 Heavy-duty bucket
*5 China source
2A-78
AH_25.book Page 79 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width
Weight
Without side With side Arm length
SAE, PCSA CECE kg (lb) m (ft.in)
3 3 cutters cutters (With side cutters)
m (cu.yd) m (cu.yd)
mm (in) mm (in)
2.00 2.50 3.05
PC220-7, PC220LC-7 (6'7") (8'2") (10')
0.72 (0.94) 0.65 (0.85) 900 (35.4") 1005 (39.6") 658 (1450)
1.00 (1.31) 0.90 (1.18) 1155 (45.5") 1260 (49.6") 734 (1620)
1.14 (1.49) 1.00 (1.31) 1300 (51.2") 1405 (55.3") 793 (1750)
1.26 (1.65) 1.10 (1.44) 1400 (55.1") 1505 (59.3") 845 (1860)
2.00 2.50 3.05 3.50
PC220-7*5, PC220LC-7*5 (6'7") (8'2") (10') (11'6")
0.72 (0.94) 0.65 (0.85) 900 (35.4") 1005 (39.6") 658 (1450)
1.00 (1.31) 0.90 (1.18) 1155 (45.5") 1260 (49.6") 787 (1735)
1.17 (1.49) 1.00 (1.31) 1300 (51.2") 1405 (55.3") 858 (1892)
1.26 (1.65) 1.10 (1.44) 1400 (55.1") 1505 (59.3") 896 (1975)
3.05 3.5
PC220LC-7*** (10') (11'6")
0.54 (0.70) — 610 (24") — 732 (1614)
0.72 (0.94) — 762 (30") — 845 (1862)
0.90 (1.18) — 914 (36") — 912 (2011)
1.09 (1.43) — 1067 (42") — 1019 (2247)
1.28 (1.67) — 1219 (48") — 1092 (2407)
1.49 (1.95) — 1219 (48") — 1116 (2461)
1.68 (2.20) — 1219 (48") — 1192 (2627)
0.48 (0.63) — 610 (24") — 770 (1698)
0.67 (0.87) — 762 (30") — 890 (1963)
0.85 (1.11) — 914 (36") — 969 (2137)
1.03 (1.35) — 1067 (42") — 1078 (2377)
1.22 (1.60) — 1219 (48") — 1188 (2619)
2.4 2.9
PC228US-3, PC228USLC-3 (7'10") (9'6")
0.50 (0.65) 0.45 (0.59) 750 (29.5") 885 (34.8") 478 (1,050)
0.60 (0.78) 0.55 (0.72) 870 (34.3") 974 (38.4") 536 (1,180)
0.80 (1.05) 0.70 (0.92) 1045 (41.1") 1150 (45.3") 626 (1,380)
0.90 (1.18) 0.80 (1.05) 1200 (47.2") 1305 (51.4") 678 (1,490)
1.05 (1.37) 0.90 (1.18) 1330 (52.4") 1435 (56.5") 757 (1,670)
1.8 2.4 2.9
PC230NHD-7 (5'11") (7'10") (9'6")
0.48 (0.63) — 600 (23.6") — 480 (1058)
0.55 (0.72) — 700 (27.6") — 530 (1168)
0.63 (0.82) — 800 (31.5") — 580 (1279)
0.71 (0.93) — 900 (35.4") — 610 (1345)
0.78 (1.02) — 1000 (39.4") — 650 (1433)
0.86 (1.15) — 1100 (43.3") — 700 (1543)
0.96 (1.26) — 1200 (47.2") — 760 (1675)
1.03 (1.35) — 1300 (51.2") — 810 (1786)
1.11 (1.45) — 1400 (55.1") — 870 (1918)
1.19 (1.56) — 1500 (59.1") — 930 (2050)
1.49 (1.95) — 1600 (63.0") — 1100 (2425)
1.58 (2.07) — 1700 (66.9") — 1150 (2535)
1.68 (2.20) — 1800 (70.9") — 1200 (2645)
2.0 2.5 3.0 3.5
PC240LC-7**, PC240NLC-7** (6'7") (8'2") (9'10") (11'6")
0.55 (0.72) 600 (23.6") 780 (1720)*
0.64 (0.84) 700 (27.6") 810 (1786)*
0.73 (0.95) 800 (31.5") 840 (1852)*
0.83 (1.09) 900 (35.4") 880 (1940)*
0.92 (1.20) 1000 (39.4") 910 (2006)*
1.01 (1.32) 1100 (43.3") 940 (2072)*
1.11 (1.45) 1200 (47.2") 960 (2116)*
1.20 (1.57) 1300 (51.2") 990 (2183)*
1.29 (1.69) 1400 (55.1") 1020 (2249)*
1.40 (1.83) 1500 (59.1") 1060 (2337)*
1.49 (1.95) 1600 (63.0") 1100 (2425)*
1.58 (2.07) 1700 (66.9") 1150 (2535)*
1.68 (2.20) 1800 (70.9") 1200 (2645)*
1.79 (2.34) 1900 (74.8") 1250 (2756)*
1.89 (2.47) 2000 (78.4") 1300 (2866)*
* Without side cutters For the source of each model, see the tables from 2A-14 to 2A-26.
** UK source
*** USA source
*4 Heavy-duty bucket
*5 China source
2A-79
AH_25.book Page 80 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width
Weight Arm length
SAE, PCSA CECE Without side With side kg (lb)
cutters cutters m (ft.in)
m3 (cu.yd) m3 (cu.yd) mm (in) mm (in)
(With side cutters)
3.05 3.5
PC270LC-7*** (10') (11'6")
0.80 (1.05) — 762 (30") — 893 (1968)
1.01 (1.32) — 914 (36") — 980 (2160)
1.22 (1.59) — 1067 (42") — 1089 (2401)
1.43 (1.87) — 1219 (48") — 1175 (2591)
1.64 (2.15) — 1219 (48") — 1260 (2777)
1.87 (2.45) — 1219 (48") — 1325 (2921)
0.74 (0.97) — 610 (24") — 979 (2159)
0.95 (1.24) — 762 (30") — 1074 (2367)
1.16 (1.51) — 914 (36") — 1194 (2633)
1.37 (1.79) — 1219 (48") — 1314 (2897)
2.0 2.5 3.05 3.5
PC290LC-7**, PC290NLC-7** (6'7") (8'2") (10') (11'6")
0.65 (0.85) 0.58 (0.76) 600 (23.6") — 686 (1512)*
0.74 (0.97) 0.66 (0.86) 700 (27.6") — 740 (1631)*
0.95 (1.24) 0.85 (1.11) 900 (35.4") — 848 (1870)*
1.16 (1.52) 1.04 (1.36) 1100 (43.3") — 956 (2108)*
1.37 (1.79) 1.27 (1.66) 1300 (51.2") — 1064 (2346)*
1.58 (2.07) 1.39 (1.82) 1500 (59.1") — 1172 (2584)*
1.80 (2.35) 1.56 (2.04) 1700 (66.9") — 1280 (2822)*
2.10 (2.75) 1.89 (2.08) 1750 (68.9") — 1230 (2712)*
2.2 2.55 3.185 4.02
PC300-7, PC300LC-7 (7'3") (8'4") (10'5") (13'2")
0.52 (0.68) 0.48 (0.63) 610 (24") 740 (29.1") 664 (1460)
1.14 (1.49) 1.00 (1.31) 1145 (45.1") 1275 (50.2") 900 (1980)
1.40 (1.83) 1.20 (1.57) 1340 (52.8") 1445 (56.9") 1015 (2240)
1.40 (1.83)** 1.20 (1.57) 1458 (54.7") — 1508 (3320)
1.60 (2.09) 1.40 (1.83) 1515 (59.6") 1645 (64.8") 1102 (2430)
1.80 (2.35) 1.60 (2.09) 1700 (66.9") — 1115 (2460)
3.19 4.02
PC300LC-7***, PC300HD-7 (10'5") (13'2")
0.88 (1.15) — 762 (30") — 1029 (2268)*
1.11 (1.45) — 914 (36") — 1123 (2476)*
1.35 (1.76) — 1067 (42") — 1246 (2747)*
1.58 (2.07) — 1219 (48") — 1313 (2895)*
1.82 (2.38) — 1372 (54") — 1425 (3142)*
0.84 (1.10) — 762 (30") — 1157 (2550)*
1.10 (1.40) — 914 (36") — 1250 (2755)*
1.31 (1.71) — 1067 (42") — 1394 (3074)*
1.55 (2.02) — 1219 (48") — 1504 (3316)*
1.78 (2.33) — 1372 (54") — 1573 (3467)*
3.185 —
PC350-7, PC350LC-7 (10'5")
1.40 (1.83)*6 1.20 (1.57) 1458 (54.7") — 1508 (3320) —
2.2 2.55 3.185 4.02
PC300-7*5 (7'3") (8'4") (10'5") (13'2")
1.40 (1.83) 1.20 (1.57) 1340 (52.8") 1445 (56.9") 1012 (2231)
1.40 (1.83)*6 1.20 (1.57) 1340 (52.8") 1445 (56.9") 1301 (2868)
1.60 (2.09) 1.40 (1.83) 1515 (59.6") 1645 (64.8") 1196 (2637)
3.045 3.5 4.2
PC308USLC-3 (10'0") (11'6") (13'9")
0.67 (0.88) — 600 (24") — 745 (1642)
0.80 (1.05) — 762 (30") — 893 (1968)
1.01 (1.31) — 914 (36") — 980 (2160)
1.22 (1.59) — 1067 (42") — 1089 (2401)
1.43 (1.87) — 1219 (48") — 1175 (2591)
1.64 (2.15) — 1219 (48") — 1260 (2777)
1.87 (2.45) — 1219 (48") — 1325 (2921)
2.2 2.55 3.19 4.02
PC340LC-7, PC340NLC-7 (7'3") (8'4") (10'6") (13'2")
0.60 (0.78) — 600 (23.6") — 684 (1508)*
1.12 (1.46) — 1000 (39.4") — 873 (1925)*
1.38 (1.81) — 1200 (47.2") — 977 (2154)*
1.65 (2.16) — 1400 (55.1") — 1062 (2341)*
1.79 (2.34) — 1500 (59.1") — 1104 (2438)*
1.92 (2.51) — 1600 (63") — 1166 (2570)*
2.12 (2.77) — 1750 (68.9") — 1230 (2712)*
2.38 (3.11) — 1800 (70.9") — 1450 (3197)*
* Without side cutters *5 China source For the source of each model, see the tables from 2A-14 to 2A-26.
** UK source *6 Rock bucket
*** USA source
2A-80
AH_25.book Page 81 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width
Weight
Without side With side Arm length
SAE, PCSA CECE kg (lb) m (ft.in)
3 3 cutters cutters (With side cutters)
m (cu.yd) m (cu.yd)
mm (in) mm (in)
2.2 2.55 3.185 4.02
PC360-7*5 (7'3") (8'4") (10'6") (13'2")
1.6 (2.09) 1.40 (1.83) 1515 (59.6") 1633 (64.3") 1615 (3560)
2.2 2.55 3.185 4.02
PC380LC-7 (7'3") (8'4") (10'5") (13'2")
1.12 (1.46) — 1000 (39.4") — 873 (1925)
1.38 (1.81) — 1200 (47.2") — 977 (2154)
1.65 (2.16) — 1400 (55.1") — 1062 (2341)
1.79 (2.34) — 1500 (59.1") — 1104 (2434)
1.92 (2.51) — 1600 (63.0") — 1166 (2571)
2.12 (2.77)*6 — 1750 (68.9") — 1230 (2712)
2.38 (3.11) — 1750 (70.9") — 1450 (3197)
2.54 (3.32) — 1850 (72.8") — 1820 (4012)
2.4 2.9 3.38 4.0
PC400-7, PC400LC-7 (7'10") (9'6") (11'1") (13'1")
1.30 (1.70) 1.20 (1.57) 1120 (44.1") 1270 (50") 1115 (2458)
1.60 (2.09) 1.40 (1.83) 1270 (50") 1420 (55.9") 1197 (2639)
1.90 (2.49) 1.70 (2.22) 1475 (58.1") 1625 (64") 1358 (2873)
1.90 (2.49)*6 1.70 (2.22) — 1625 (64") 1966 (3757)
2.06 (2.69) 1.80 (2.35) 1565 (61.6") 1715 (67.5") 1391 (3067)
2.10 (2.75)*6 1.90 (2.49) — 1745 (68.7") 2035 (4490)
2.20 (2.88) 2.00 (2.62) 1715 (67.5") — 1396 (3757)
2.4 2.9 3.38 4.0 4.8
PC400LC-7*** (7'10") (9'6") (11'1") (13'1") (15'9")
1.12 (1.47) — 762 (30") — 1266 (2790)
1.35 (1.76) — 914 (36") — 1393 (3072)
1.64 (2.15) — 1067 (42") — 1536 (3386)
1.94 (2.54) — 1219 (48") — 1646 (3629)
2.25 (2.94) — 1372 (54") — 1790 (3947)
2.55 (3.34) — 1524 (60") — 1903 (4195)
2.87 (3.75) — 1676 (66") — 2045 (4509)
3.17 (4.15) — 1676 (66") — 2156 (4752)
3.38 —
PC450-7, PC450LC-7 (11'1")
1.90 (2.49) 1.70 (2.22) — 1625 (64.0")* 7 1966 (4330) —
2.10 (2.75)*6 1.90 (2.49) — 2035 (68.7")* 7 2035 (4490) —
2.4 2.9 3.38 4.0 4.8
PC450LC-7** (7'10") (9'6") (11'1") (13'1") (15'9")
1.30 (1.70) — 1000 (39.4") — 1150 (2535)
1.65 (2.08) — 1200 (47.2") — 1350 (2976)
2.00 (2.35) — 1400 (55.1") — 1679 (3701)
2.30 (3.01) — 1600 (63.0") — 1800 (3968)
2.70 (3.53) — 1800 (70.9") — 1997 (4403)
6.6 7.3 7.66
(21'9") (23'11") (25'2")
2.9 3.5 3.5 4.3 5.2
PC600-7, PC600LC-7 (9'6") (11'6") (11'6") (14'1") (17'1")
2.0 (2.62) 1.8 (2.35) 1250 (49.2") 1430 (56.3") 2200 (4850) — —
2.3 (3.01) 2.1 (2.75) 1400 (55.1") 1580 (62.2") 2382 (5250) — —
2.7 (3.53) 2.4 (3.14) 1600 (63.0") 1780 (70.1") 2505 (5520) — —
2.8 (3.66) 2.5 (3.27) 1870 (73.6") 1870 (73.6")* 8 2981 (6570) — — — —
3.1 (4.05) 2.8 (3.66) 2000 (78.7")*8 2000 (78.7")* 8 3100 (6830) *9
3.5 (4.58) 3.1 (4.05) 2120 (83.5")*8 2120 (83.5")* 8 3406 (7510) — — — —
* Without side cutters For the source of each model, see the tables from 2A-14 to 2A-26.
** UK source
*** USA source
*5 China source
*6 Quarry bucket
*7 With side shrouds
*8 Bucket lip width
*9 Installed to LC crawler
2A-81
AH_25.book Page 82 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 2.1 t/m3 (3500 lb/cu.yd)
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width Boom length m (ft, in)
Weight
Without side With side kg (lb)
SAE, PCSA CECE Arm length
m3 (cu.yd) m3 (cu.yd) cutters cutters (With side cutters) m (ft.in)
mm (in) mm (in)
7.66 7.66
(25'2") (25'2")
2.9 3.5
PC600LC-6** (9'6") (11'6")
2.4 (3.14) 2.1 (2.75) 1320 (52.0") 1400 (55.1") 2410 (5310)
2.7 (3.53) 2.4 (3.14) 1600 (63.0") 1680 (66.1") 2795 (6160)
2.8 (3.66) 2.5 (3.27) 1655 (65.2") 1705 (67.1") 2795 (6162)
3.5 (4.58) 3.1 (4.05) 1850 (72.8") 1900 (74.8") 3325 (7330)
7.3
(23'11")
3.5
PC600-6 QUARRY (11'6")
2.4 (3.14) 2.1 (2.75) 1320 (52.0") 1400 (55.1") 2410 (5310)
2.7 (3.53) 2.4 (3.14) 1600 (63.0") 1680 (66.1") 2795 (6160)
2.8 (3.66) 2.5 (3.27) 1655 (65.2") 1705 (67.1") 2795 (6162)
3.5 (4.58) 3.1 (4.05) 1850 (72.8") 1900 (74.8") 3325 (7330)
6.6
(21'9")
2.9
PC600SE-6** (9'6")
2.4 (3.14) 2.1 (2.75) 1320 (52.0") 1400 (55.1") 2410 (5310)
2.7 (3.53) 2.4 (3.14) 1600 (63.0") 1680 (66.1") 2795 (6160)
2.8 (3.66) 2.5 (3.27) 1655 (65.2") 1705 (67.1") 2795 (6162)
3.5 (4.58) 3.1 (4.05) 1850 (72.8") 1900 (74.8") 3325 (7330)
3.6 4.6 5.6
PC750-7 (11'10") (15'1") (18'4")
2.8 (3.66) 2.5 (3.27) 1550 (61") 1695 (66.7") 2740 (6040)
3.1 (4.05) 2.8 (3.66) 1700 (66.9") 1845 (72.6") 2960 (6530)
3.4 (4.45) 3.0 (3.92) 1820 (71.7") 1920 (75.6") 3500 (7720)
2.945
PC750SE-6 (9'8")
4.0 (5.23) 3.5 (4.58) 2000 (78.7") 2100 (82.8") 3435 (7570)
4.3 (5.62) 3.8 (4.97) 2150 (84.6") 2250 (88.7") 3870 (8530)
4.5 (5.89) 4.0 (5.23) 2230 (87.8") 2330 (91.7") 4050 (8930)
3.6
PC800-7 (11'10")
3.4 (4.45) 3.0 (3.92) 1820 (71.7") 1870 (73.6") 3500 (7720)
2.945 3.6
PC800SE-7 (9'8") (11'10")
4.0 (5.23)*9 3.5 (4.58) 2000 (78.7") 2105 (82.9") 4000 (8820)
4.0 (5.23) 3.5 (4.58) 2000 (78.7") 2105 (82.9") 3435 (7570)
4.3 (5.62) 3.8 (4.97) 2150 (84.6") 2255 (88.8") 3870 (8530)
4.5 (5.89) 4.0 (5.23) 2230 (87.8") 2330 (91.9") 4050 (8930)
2.92 3.6
PC750SE-6**, PC750LC-6** (9'7")*7 (11'10")*8
3.6 (4.71) — 1750 (68.9") — 3575 (7880)**
4.0 (5.23) — 1950 (76.8") — 3700 (8160)**
4.4 (5.75) — 2140 (84.3") — 3800 (8380)**
5.1 (6.67) — 2480 (97.6") — 3925 (8650)**
5.6 (7.32) — 2730 (107.5") — 4025 (8870)**
6.0 (7.85) — 2920 (115.4") — 4100 (9040)**
8.2 10.0
(26'11") (32'10")
3.6 4.6 5.6 4.6 5.6
PC750LC-7*** (11'10") (15'1") (18'4") (15'1") (18'4")
2.89 (3.78) — 1370 (54") — 3190 (7032)
3.04 (3.98) — 1524 (60") — 3769 (8309)
3.42 (4.48) — 1676 (66") — 3993 (8802)
3.70 (4.85) — 1676 (66") — 3652 (8052)
1.70 (2.23) — 914 (36") — 2544 (5609)
1.93 (2.52) — 1067 (42") — 2963 (6533)
2.09 (2.73) — 1067 (42") — 2732 (6023)
2.49 (3.25) — 1220 (48") — 2998 (6610)
* Without side cutters For the source of each model, see the tables from 3A-10 to 3A-23.
** UK source
*** For USA
*7 Use with 7.1 m (23'4") boom
*8 Use with 8.2 m (26'11") boom
*9 For heavy duty
2A-82
AH_25.book Page 83 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
General purpose use, weight up to 2.1 t/m3 (3500 lb/cu.yd)
General purpose use, weight up to 1.8 t/m3 (3000 lb/cu.yd)
General purpose use, weight up to 1.5 t/m3 (2500 lb/cu.yd)
Light duty work, weight up to 1.2 t/m3 (2000 lb/cu.yd)
Not usable.
Bucket capacity (heaped) Width Weight
Without side With side kg (lb) Boom length + Arm length
SAE, PCSA CECE (With side m (ft.in)
cutters cutters*
m3 (cu.yd) m3 (cu.yd) mm (in) mm (in) cutters)
3.4 4.5 5.7
PC1250-7, PC1250LC-7 (11'2") (14'9") (18'8")
3.4 (4.4) 3.0 (3.9) 1500 (59.1") 1670 (65.7") 3600 (7940)*9 —
4.0 (5.2) 3.5 (4.6) 1710 (67.3") 1880 (74") 3800 (8380)*9
5.0 (6.5) 4.3 (5.6) 2050 (80.7") 2220 (87.4") 4400 (9700)*9 —
5.2 (6.8) 4.5 (5.9) 2050 (80.7") 2110 (83.1") 5100 (11240) — —
3.4
PC1250SP-7 (11'2")
6.7 (8.8) 5.9 (7.7) 2280 (89.8") 2340 (92.1") 6000 (13230)*9
8.7 + 3.9 9.1 + 4.1 11.4 + 5.0
PC1800-6 (28'7" + 12'10") (29'10" + 13'5") (37'5" + 16'5")
5.6( 7.3) 5.0 (6.5) 1770 (69.7") 1930 (76") 7570 (16690) *
8.5 (11.1) 7.6 (9.9) 2240 (88.2") 2400 (94.5") 9390 (20700) *
10.1 (13.2) 9.0 (11.8) 2540 (100") 2700 (106") 9600 (21160)
11.0 (14.4) 9.8 (12.8) 2540 (100") 2590 (102") 9370 (20660) —
12.0 (15.7) 11.0 (14.4) 2720 (107") 2770 (109") 9985 (22010) — —
These charts are based on over-side stability with fully loaded bucket at maximum reach.
Heavy duty work
General digging and loading
Light material work
Bucket capacity (heaped) Width Weight
kg (lb) Boom length + Arm length
SAE, PCSA CECE Without side With side (With side
cutters cutters** m (ft.in)
3
m (cu.yd) 3
m (cu.yd) cutters and
mm (in) mm (in) wp-2**)
8.0 + 3.6
PC1400-1 (26'3"+ 11'10")
8.5 (11.1) 7.5 (9.8) 2590 (102") 2590 (102") 7550 (16640)
9.5 (12.4) 8.5 (11.1) 2740 (108") 2740 (108") 7920 (17460)
8.6 + 4.0
PC3000-1 (28'3"+ 13'1")
15 (19.6) 13.3 (17.4) 3400 (134") 3400 (134") 16400 (36160)
9.75 + 4.5
PC4000-6 (32'0"+ 14'9")
22 (28.8) 19 (24.9) 3800 (150") 3800 (150") 23300 (51370)
10 + 5.1
PC5500-6 (32'10"+ 16'9")
28 (36.6) 24.3 (31.8) 4220 (166") 4220 (166") 30400 (64020)
11.5 + 5.5
PC8000-6 (37'9"+ 18'1")
38 (49.7) 33 (43.2) 4600 (181") 4600 (181") 42400 (93480)
42 (54.9) 36.5 (47.7) 4600 (181") 4600 (181") 42720 (94180)
For the source of each model, see the tables from 2A-14 to 2A-26.
* It is necessary to use strengthened boom and arm
** Wear package number
*** Side cutters, which increase the width of bucket, are not standard
* 9
With side shrouds
2A-83
AH_25.book Page 84 Tuesday, March 23, 2004 9:41 AM
Teeth Selection
1. Teeth designed by Komatsu
Vertical pin type Horizontal pin type
Self- Self- Super self-
Standard Long-life Standard Long-life
sharpened sharpened sharpened
tooth tooth tooth tooth
tooth tooth tooth
PC120-6
—
up to PC210-7
PC220-7
—
up to PC380-7
PC400-7
—
PC450-7
PC750-7
— — —
PC800-7
PC1250-7 — — — —
: Available
2A-84
AH_25.book Page 85 Tuesday, March 23, 2004 9:41 AM
• Centerline tooth.
FLARE
• Centerline tooth for general purpose
applications on excavators.
• Increased productivity.
• Slim profile with wide leading edge to
reduce spillage.
• Maximizes bucket capacity.
ROCK CHISEL
• Excellent penetration.
• Centerline tooth with a slim profile and
narrow bite used mainly on excavators.
• Excellent wear life.
• Appropriate for hard and abrasive soil and
rock applications.
• Stays sharp.
ABRASION PANELLED
• Centerline tooth for general purpose and
heavy duty applications on excavators and
loaders.
• Provides high wear metal and a better
wear life.
• Appropriate for applications in abrasive
materials.
• Self-sharpening.
• Excellent penetration.
• Non-centerline tooth with heavy bottom
pad for loaders.
• Excellent wear life.
• Appropriate for hard and abrasive soil and
shot rock applications.
• Stays sharp.
2A-85
AH_25.book Page 86 Tuesday, March 23, 2004 9:41 AM
ABRASION
TIGER
• Non-centerline tooth.
• Maximum penetration in compact soil.
TWIN TIGER
• Non-centerline tooth.
• Increased productivity.
• For use in compact material for maximum
penetration.
2A-86
AH_25.book Page 87 Tuesday, March 23, 2004 9:41 AM
TOOTH SHAPES
Model 1 2 3 4 5 6 7 8 9 10
PC120, PC160 — —
PC200, PC210, PC220, PC230 — —
PC300, PC350, PC400, PC450 —
PC600, PC750, PC800 — — — —
: Available
2A-87
AH_25.book Page 88 Tuesday, March 23, 2004 9:41 AM
TOOTH SHAPES
Model 1 2 3 4 5 6 7 8 9 10
PC20, PC30, PC45 — — — — — —
PC120 — — —
PC160 —
PC200, PC220 —
PC300, PC350 —
PC400, PC450
PC600, PC750, PC800
PC1250 — — —
: Available
2A-88
AH_25.book Page 89 Tuesday, March 23, 2004 9:41 AM
TOOTH SHAPES
Model 1 2 3 4 5 6 7 8 9 10
PC400 — —
PC1800 — — — — — — —
: Available
2A-89
AH_25.book Page 90 Tuesday, March 23, 2004 9:41 AM
T T T T
W1 W2 W1 W2 W1 W2 W1 W2
L L L L
T T T T
W1 W1 W2 W1 W2 W1 W2
L L L L
FVBH0189
2A-90
AH_25.book Page 91 Tuesday, March 23, 2004 9:41 AM
Boom/Arm + Bucket
Long boom
Long arm + Small capacity bucket
FVBH0242
2) Larger production
Short boom
Short arm + Large capacity bucket
FVBH0243
FVBH0244
4) Heavy-duty work
Strengthened boom
Strengthened arm + Heavy-duty bucket
FVBH0245
2. Wrong combination
Wrong
1) Long Arm with Large Capacity Bucket
If the machine is operated with a long arm and a
large capacity bucket with a capacity larger than
recommended, the machine will become unstable,
and it will also lose digging power, so the operating
efficiency will drop. In particular, if a strong shock
load is applied to the bucket, there is danger that the
arm may break.
FVBH0246
2) Additional Counterweight
If an excessive capacity bucket or heavy attachment Wrong
is installed, the machine will become unstable, so it
is common to see additional counterweights used.
However, this means that an excessive load is
applied not only to the work equipment and
undercarriage, but also to the whole machine, so this
will lead to a reduction in the service life of the
machine.
FVBH0247
2A-91
AH_25.book Page 92 Tuesday, March 23, 2004 9:41 AM
2) Digging function
Loading shovel : This is better for loading blasted rocks where there are many large lumps and digging force
is required. When digging flat surfaces, its horizontal pushing force is strong and it can
show its power, but it is difficult for it to use its pushing force when digging above ground
level.
Backhoe : This is an all-round attachment for digging and loading. When increasing the bucket size to
ensure production volume, make the work equipment (arm, boom) shorter.
(Note: Digging a
(Note: Digging
slope a
and loading)
slope and loading)
Blasted rock
Blasted rock
Natural
ground Natural
Natural
ground Natural
ground
ground About 20º Deep
Blasted rock
Short
Long Blasted rock Deep
Short
Long
Long FVBH0249
Long
NOTE: The bucket size depends on the specific gravity (loose) of the material loaded. For details, see
Bucket and Arm Combination.
2A-92
AH_25.book Page 93 Tuesday, March 23, 2004 9:41 AM
2A-93
AH_25.book Page 94 Tuesday, March 23, 2004 9:41 AM
2A-94
AH_25.book Page 95 Tuesday, March 23, 2004 9:41 AM
11 (m) 12 (m)
10 11
9 10
9
8
8
7
7
6
6
5
5
4 4
3 3
2 2
1 1
G.L. 0 G.L.
0
1 1
2
2
45 3
3
3.5 45 4
4
5
5
6
6 7
7 8
8 9
12 11 10 9 8 7 6 5 4 3 2 1 0 13 12 11 10 9 8 7 6 5 4 3 2 1 0
(m) FVBH0270 (m) FVBH0314
2A-95
AH_25.book Page 96 Tuesday, March 23, 2004 9:41 AM
0
1
2
3
45 4
4.5 :SE
5
5.5 :STD
6
7
8
9
10
11
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
(m) FVBH0317
7
PC1250-7 :STD PC1250SP-7
6
5
4
3
2
1
0
1
0.5 2
3
4
45
5 :SP
6 :STD
0.5
7
8
9
11
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FVBH0272
2A-96
AH_25.book Page 97 Tuesday, March 23, 2004 9:41 AM
7
6
5
4
3
2
1
0
1
0.5 2
3
60 4
5
5.5
6
7
8
9
11
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
FVPM2976
[ft] [m]
54
16
51
15
48
14
45
13
42
12
39
36 11
33 10
30 9
27 8
24 7
21
6
18
5
15
4
12
3
9
6 2
3 1
0 0
-3 -1
-6 -2
-9 -3
-12
-4
-15 -5
-18
-6
-21
-7
-24
-8
-27
-30 -9
-33 -10
18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 [m]
60 57 54 51 48 45 42 39 36 33 30 27 24 21 18 15 12 9 6 3 0 [ft]
2A-97
AH_25.book Page 98 Tuesday, March 23, 2004 9:41 AM
63 60 57 54 51 48 45 42 39 36 33 30 27 24 21 18 15 12 9 6 3 0 [ft]
[ft] [m]
57
17
54
16
51
15
48
45 14
42 13
39 12
36 11
33 10
30 9
27 8
24 7
21
6
18
5
15
4
12
9 3
6 2
3 1
0 0
-3 -1
-6 -2
-9 -3
-12
-4
-15
-5
-18
-6
-21
-24 -7
-27 -8
-30 -9
21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 [ft]
69 63 63 60 57 54 51 48 45 42 39 36 33 30 27 24 21 18 15 12 9 6 3 0 [m]
2A-98
AH_25.book Page 99 Tuesday, March 23, 2004 9:41 AM
[ft] 0 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 51 54 57 60 63 66 69 72 75 78 81
2A-99
AH_25.book Page 100 Tuesday, March 23, 2004 9:41 AM
Production EXCAVATORS
(BACKHOE)
Estimated Hourly Production
ESTIMATED
CYCLE BUCKET SIZE** (CU.M) OR (CU.YD)
TIME
SEC. MIN. 0.2 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3
10.0 0.17 72 108 180 252 324
11.0 0.18 65 98 164 229 295 360 425 491
12.0 0.20 60 90 150 210 270 330 390 450 510 570 630 690 750
13.0 0.22 55 83 138 194 249 305 360 415 471 526 582 637 692 748 803 858 914 969 1025 1080 1135
15.0 0.25 48 72 120 168 216 264 312 360 408 456 504 552 600 648 696 744 792 840 888 936 984 1032
17.0 0.28 42 64 106 148 191 233 275 318 360 402 445 487 529 572 614 656 699 741 784 826 868 911
19.0 0.32 38 57 95 133 171 208 246 284 322 360 398 436 474 512 549 587 625 663 701 739 777 815
21.0 0.35 34 51 86 120 154 189 223 257 291 326 360 394 429 463 497 531 566 600 634 669 703 737
24.0 0.40 30 45 75 105 135 165 195 225 255 285 315 345 375 405 435 565 595 525 555 585 615 645
27.0 0.45 27 40 67 93 120 147 173 200 227 253 280 307 333 360 387 413 440 467 493 520 547 573
30.0 0.50 24 36 60 84 108 132 156 180 204 228 252 276 300 324 348 372 396 420 444 468 492 516
35.0 0.58 175 195 216 237 257 278 298 319 339 360 381 401 422 442
40.0 0.67 279 297 315 333 351 369 387
ESTIMATED
CYCLE BUCKET SIZE** (CU.M) OR (CU.YD)
TIME
SEC. MIN. 4.5 4.7 4.9 5.1 5.3 5.5 5.7 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0
15.0 0.25 1080 1128 1176 1224 1272 1320 1368
17.0 0.28 953 995 1038 1080 1122 1165 1207
19.0 0.32 853 891 928 966 1004 1042 1080 1137 1231 1326 1421 1516 1611 1705 1800 1895 1989 2084 2179 2274
21.0 0.35 771 806 840 874 909 943 977 1028 1114 1200 1286 1371 1457 1543 1629 1714 1800 1886 1971 2057
24.0 0.40 675 705 735 765 795 825 855 900 975 1050 1125 1200 1275 1350 1425 1500 1575 1650 1725 1800
27.0 0.45 600 627 653 680 707 733 760 800 867 933 1000 1067 1133 1200 1267 1333 1400 1467 1533 1600
30.0 0.50 540 564 588 612 636 660 684 720 780 840 900 960 1020 1080 1140 1200 1260 1320 1380 1440
35.0 0.58 463 483 504 525 545 566 586 617 668 720 771 823 874 926 977 1029 1080 1131 1183 1234
40.0 0.67 405 423 441 459 477 495 513 540 585 630 675 720 765 810 855 900 945 990 1035 1080
45.0 0.75 480 520 560 600 640 680 720 760 800 840 880 920 960
ESTIMATED
CYCLE BUCKET SIZE** (CU.M) OR (CU.YD)
TIME
SEC. MIN. 12.5 13.0 13.5 14.0 15.0 16.0 18 20 22 25 28 30 35 38 40
15.0 0.25
17.0 0.28
19.0 0.32 2368 2463
21.0 0.35 2143 2229 2314 2400 2571 3031 3085
24.0 0.40 1875 1950 2025 2100 2250 2400 2700 3000 3300 3750 4200 4500 5250 5700 6000
27.0 0.45 1667 1733 1800 1866 2000 2133 2400 2666 2933 3333 3733 4000 4666 5066 5333
30.0 0.50 1500 1560 1620 1680 1800 1920 2160 2400 2640 3000 3360 3600 4200 4560 4800
35.0 0.58 1286 1337 1388 1440 1543 1645 1851 2057 2263 2571 2880 3085 3600 3908 4114
40.0 0.67 1125 1170 1215 1260 1350 1440 1620 1800 1980 2250 2520 2700 3150 3420 3600
45.0 0.75 1000 1040 1080 1120 1200 1280 1440 1600 1760 2000 2240 2400 2800 3040 3200
Actual production = Estimated Hourly Production × Bucket Fill Factor × Job Efficiency
Bucket fill factor (K) (PC60~PC1800) Job efficiency (E)
Excavating conditions K Excavating conditions E
Easy excavating 1.1 ~ 1.2 Good 0.83
Average excavating 1.0 ~ 1.1 Average 0.75
Rather difficult excavating 0.8 ~ 0.9 Rather poor 0.67
Difficult excavating 0.7 ~ 0.8 Poor 0.58
2A-100
AH_25.book Page 101 Tuesday, March 23, 2004 9:41 AM
EXCAVATORS
(BACKHOE)
2A-101
AH_25.book Page 102 Tuesday, March 23, 2004 9:41 AM
EXCAVATORS
(BACKHOE)
2A-102
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2B
MINIMAL SWING RADIUS
EXCAVATORS (UU)
UU stands for “Ultra Urban” machine.
CONTENTS
Features .................................................................... 2B-3
Specifications ........................................................... 2B-4
Dimensions ............................................................... 2B-5
Working ranges, Digging Force .............................. 2B-6
Lifting capacity ......................................................... 2B-7
2B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
B<A
C z 1.2A
B C
2B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
2B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Model
PC58UU-3 PC78UU-6 PC128UU-2
Item
OPERATING WEIGHT* kg (lb) 5290 (11,670) 7670 (16,910) 13580 (29,940)
FLYWHEEL (SAE) HP (kW)/RPM 39 (29.4)/2400 54 (40.5)/1850 86 (64)/2200
HORSEPOWER: (DIN) PS (kW)/RPM 40 (29.4)/2400 55 (40.5)/1850 87 (64)/2200
BUCKET CAPACITY RANGE 0.055~0.22 0.09~0.34 0.18~0.50
(SAE) m3 (cu.yd) (0.07) (0.29) (0.12) (0.44) (0.24) (0.65)
PERFORMANCE:
Swing speed RPM 10.0 10.0 10.0
Max. travel speed km/h (MPH) Hi 4.5 (2.8) Hi 4.5 (2.8) Hi 4.6 (2.9)
Lo 2.7 (1.7) Lo 3.0 (1.9) Lo 3.2 (2.0)
DIMENSIONS:
(see the page of dimensions)
Front swing radius 1060(3'5") 1200 (3'11") 1345 (4'5")
mm (ft.in)
Offset width L:910 (3') L:1030 (3'5") L:1170 (3'10")
R:730 (2'5") R:1065 (3'6") R:1150 (3'9")
Tail swing radius 1035 (3'5") 1240 (4'1") 1480 (4'10")
ENGINE: KOMATSU KOMATSU KOMATSU
Model 4D88E S4D95LE S4D102E
No. of cylinders- mm 4-88 × 90 4-95 × 115 4-102 × 120
bore × stroke (in) (3.46 × 3.54) (3.74 × 4.53) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 2.19 (134) 3.92 (239) 3.92 (239)
HYDRAULIC SYSTEM: 2 × Variable piston 2 × Variable piston 1 × Variable piston
Hydraulic pump 1 × Gear pump 1 × Gear pump 1 × Gear pump
Max. oil flow ltr. (U.S. Gal)/min. 135 (35.9) 160 (42.2) 226.5 (59.7)
Max. oil pressure kg/cm2 (PSI) 265 (3770) 270 (3840) 355 (5050)***
Track shoe width/ mm (in)/ 400 (16")/ 450 (18")/ 600 (24")/
ground pressure kg/cm2 (PSI) 0.31 (4.4) 0.33 (4.7) 0.36 (5.1)
CAPACITY (Refilled):
Fuel tank ltr.(U.S. Gal) 80 (21.1) 125 (33) 200 (52.8)
Hydraulic oil tank 36 (9.5) 64 (16.9) 69 (18.2)
*: MACHINE SPEC.
• Bucket (SAE) 0.22 (0.29) 0.28 (0.37) 0.45 (0.59)
m3 (cu.yd)
• Upper attachment Cab Cab Cab
• Track shoe Rubber shoe Triple grouser Triple grouser
* Operating weight includes coolant, lubricants, full fuel tank, operator 80 kg (180 lb) and, indicated implement, shoes and upper
attachment.
*** Travel circuit
2B-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
E L
K
C
G G.L D
I
H A
J B FVBH0028
A B C D E F G H I J K L Boom Arm
mm mm mm mm mm mm mm mm mm mm mm mm Iength Iength
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (in) (ft.in) (ft.in) (ft.in) m (ft.in) m (ft.in)
1545 5335 1.62
1910 2470 630 400 1935 2610 320 1600 400 2000 (5'1") (17'6") 3.41 (5'4")
PC58UU-3
(6'3") (8'1") (2'1") (1'4") (6'4") (8'7") (1'1") (5'3") (16") (6'7") 2625 5385 (11'2") 2.07
(8'7") (17'8") (6'10")
2235 2840 735 470 2330 2730 360 1870 450 2320 1745 6060 3.75 1.72
PC78UU-6
(7'4") (9'4") (2'5") (1'7") (7'8") (8'11") (1'2") (6'2") (18") (7'7") (5'9") (19'11") (12'4") (5'8")
2750 3480 855 590 2490 2730 390 1990 600 2590 1935 7435 4.29 2.13
PC128UU-2
(9') (11'5") (2'10") (1'11") (8') (9') (1'5") (6'5") (20") (8'1") (6'2") (24'1") (14'1") (7')
2B-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
F
A E
D
C
FVBH0029
2B-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
L
A : Reach from swing center
B : Bucket hook height
C : Lifting capacity
L : Arm length
B Cf : Rating over front
Cs : Rating over side
C MAX: Rating at maximum reach
kg(lb) FVBH0043
PC58UU-3
Conditions:
Boom : 3410 mm (11'12"), Bucket (SAE) : 0.22 m3 (0.29cu.yd), Shoes : 400 mm (16") unit: kg (lb)
A MAX 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 1620 mm (5'4") With blade on ground
4.6 m *1030 *1030 *1380 *1380
(15') (2290) (2290) (3050) (3050)
3.0 m *990 660 *1000 760 *1530 *1530
(10') (2200) (1450) (2200) (1690) (3380) (3380)
0.0 m *1360 500 *1470 650 *2290 *1230 *1400 *1400
(0') (3010) (1110) (3250) (1430) (5060) (2710) (3080) (3080)
-1.5 m *1410 610 *2110 1170 *1050 *610
(5') (3110) (1350) (4660) (2590) (2320) (1350)
Arm length 1620 mm (5'4") With blade above ground
4.6 m *1030 *1030 *1380 *1380
(15') (2290) (2290) (3050) (3050)
3.0 m 850 660 980 760 *1530 *1530
(10') (1870) (1450) (2170) (1690) (3380) (3380)
0.0 m 670 500 860 650 1630 *1230 *1400 *1400
(0') (1480) (1110) (1910) (1430) (3600) (2710) (3080) (3080)
-1.5 m 820 610 1570 1170
(5') (1800) (1350) (3470) (2590)
Arm length 1620 mm (5'4") With blade on ground, Additional counterweight
4.6 m *1030 *1030 *1380 *1380
(15') (2290) (2290) (3050) (3050)
3.0 m *990 720 *1000 830 *1530 *1530
(10') (2200) (1580) (2200) (1840) (3380) (3380)
0.0 m *1360 560 *1470 720 *2290 1340 *1400 *1400
(0') (3010) (1230) (3250) (1580) (5060) (2970) (3080) (3080)
-1.5 m *1410 670 *2110 1290 *1050 680
(5') (3110) (1490) (4660) (2850) (2320) (1500)
Arm length 1620 mm (5'4") With blade above ground, Additional counterweight
4.6 m *1030 *1030 *1380 *1380
(15') (2290) (2290) (3050) (3050)
3.0 m 910 720 *1000 830 *1530 *1530
(10') (2020) (1580) (2200) (1840) (3380) (3380)
0.0 m 720 560 940 720 1760 1340 *1400 *1400
(0') (1620) (1230) (2070) (1580) (3880) (2970) (3080) (3080)
-1.5 m 890 670 1700 1290
(5') (1960) (1490) (3760) (2850)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2B-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
PC128UU-2
Conditions:
Boom: 4290 mm (14'1"), Bucket (SAE): 0.44 m3 (0.58 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 5.5 m (18') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2130 mm (7')
6.1 m 2700* 2700* 3100 2250 3550* 3550*
(20') (6000) (6000) (6900) (4900) (7800) (7800)
3.0 m 2250 1550 2450 1750 3450 2450 5500* 5050
(10') (4900) (3500) (5400) (3800) (7600) (5400) (12200) (11100)
0m 2000 1350 2200 1500 2950 2000 5950 3750
(0') (4400) (3000) (4800) (3300) (6500) (4400) (13100) (8300)
-3.0 m 2750 1900 3000 2050 2450 1650
(-10') (6100) (4200) (6600) (4500) (5400) (3600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2B-8
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2C
LIFTING CAPACITY
CONTENTS
PC15/20 ..................................................................... 2C-2
PC27/30 ..................................................................... 2C-3
PC35/40 ..................................................................... 2C-4
PC50 .......................................................................... 2C-5
PC75 .......................................................................... 2C-6
PC78US/MR .............................................................. 2C-8
PC100 ...................................................................... 2C-10
PC110 ...................................................................... 2C-11
PC120 ...................................................................... 2C-15
PC138US ................................................................. 2C-18
PC130 ...................................................................... 2C-19
PC160 ...................................................................... 2C-21
PC200 ...................................................................... 2C-23
PC210 ...................................................................... 2C-28
PC220 ...................................................................... 2C-31
PC228 ...................................................................... 2C-36
PC230 ...................................................................... 2C-37
PC240 ...................................................................... 2C-39
PC270 ...................................................................... 2C-41
PC290 ...................................................................... 2C-42
PC300 ...................................................................... 2C-44
PC340 ...................................................................... 2C-51
PC350 ...................................................................... 2C-53
PC380 ...................................................................... 2C-54
PC400 ...................................................................... 2C-55
PC450 ...................................................................... 2C-68
PC600 ...................................................................... 2C-73
PC750 ...................................................................... 2C-79
PC800 ...................................................................... 2C-84
PC1250 .................................................................... 2C-85
PC1800 .................................................................... 2C-87
2C-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC15MRX-1
Conditions:
Boom: 1760 mm (5'7"), Bucket (SAE): 0.044 m3 (0.058 cu.yd), Shoes: 230 mm (9") unit: kg (lb)
PC20MRX-1
Conditions:
Boom: 1809 mm (5'11"), Bucket (SAE): 0.066 m3 (0.086 cu.yd), Shoes: 250 mm (10") unit: kg (lb)
2C-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC27MRX-1
Conditions: Boom: 2120 mm (6'11"), Bucket (SAE): 0.08 m3 (0.105 cu.yd), Shoes: 300 mm (12") unit: kg (lb)
PC30MR-2
Conditions: Boom: 2350 mm (7'9"), Bucket (SAE): 0.09 m3 (0.12 cu.yd), Shoes: 300 mm (12") unit: kg (lb)
2C-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC35MR-2
Conditions: Boom: 2560 mm (8'5"), Bucket (SAE): 0.11 m3 (0.14 cu.yd), Shoes: 300 mm (12") unit: kg (lb)
PC40MR-2
Conditions:
Boom: 2740 mm (9'0"), Bucket (SAE): 0.14 m3 (0.18 cu.yd), Shoes: 400 mm (16") unit: kg (lb)
2C-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC50MR-2
Conditions:
Boom: 2900 mm (9'6"), Bucket (SAE): 0.16 m3 (0.21 cu.yd), Shoes: 400 mm (16") unit: kg (lb)
2C-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC75R-2
A
A : Reach from swing center
B : Bucket hook height
C : Lifting capacity
Cf : Rating over front
Cs : Rating over side
B
MAX: Rating at maximum reach
C
FVPM2801
Conditions:
One piece boom: Bucket (SAE): 0.265 m3 (0.35 cu.yd), Shoes: 450 mm (18") unit: kg (lb)
2C-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC75R-2
Conditions:
Two piece boom: 3673 mm (12'1"), Bucket (SAE): 0.265 m3 (0.35 cu.yd), Shoes: 450 mm (18") unit: kg (lb)
2C-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC78US-6
Conditions:
Boom: 3710 mm (12'2"), Bucket (SAE): 0.28 m3 (0.37 cu.yd), Shoes: 450 mm (18") unit: kg (lb)
2C-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC78MR-6
Conditions:
Boom: 3400 mm (11'2") Bucket (SAE): 0.28 m3 (0.37 cu.yd), Shoes: 450 mm (18") unit: kg (lb)
2C-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC110R-1
Conditions:
One piece boom: Bucket (SAE): 0.36 m3 (0.47 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC110R-1
Conditions:
One piece boom: Bucket (SAE): 0.36 m3 (0.47 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC110R-1
Conditions:
Two piece boom: Bucket (SAE): 0.36 m3 (0.47 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC110R-1
Conditions:
Two piece boom: Bucket (SAE): 0.36 m3 (0.47 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC120-6
Conditions:
Boom: 4600 mm (15'1"), Bucket (SAE): 0.50 m3 (0.65 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC138US-2
Conditions:
Boom: 4600 mm (15'1"), Bucket (SAE) 0.45 m3 (0.59 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC130-6 MIGHTY
Conditions:
Boom: 4600 mm (15'1''), Bucket (SAE): 0.50 m3 (0.65 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
2C-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC160LC-7
Conditions: Boom: 5150 mm (16'11"), Bucket (SAE): 0.65 m3 (0.85 cu.yd), Shoes: 500 mm (20") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (4')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2250 mm (7'5")
7.5 m 2700* 2700*
(24') (6000) (6000)
6.0 m 2400* 2400* 3250* 2850
(19') (5300) (5300) (7200) (6300)
4.5 m 2350* 2050 4450* 2850 5000* 4650
(14') (5200) (4600) (9800) (6200) (11000) (10200)
3.0 m 2450* 1800 4450 2700 6300* 4300 9700* 8150
(9') (5400) (4000) (9800) (6000) (13900) (9500) (21400) (18000)
0m 2950 1700 4150 2400 6550 3750 6750* 6750*
(0') (6600) (3800) (9200) (5400) (14500) (8200) (14900) (14900)
–3.0 m 4200 2450 6550 3700 10500* 7100 10250* 10250*
(–9') (9300) (5400) (14500) (8200) (23100) (15700) (22700) (22700)
–4.5 m 4850* 4200 7050* 7050*
(–14') (10700) (9200) (15600) (15600)
Arm length 2610 mm (8'7")
7.5 m 2200* 2200*
(24') (4900) (4900)
6.0 m 2000* 2000* 3350* 2900
(19') (4400) (4400) (7400) (6400)
4.5 m 2000* 1900 4200* 2850
(14') (4400) (4200) (9200) (6300)
3.0 m 2050* 1650 3050 1800 4500 2750 5900* 4400 8700* 8450
(9') (4600) (3700) (6700) (4000) (9900) (6000) (13000) (9700) (19200) (18600)
0m 2650* 1600 2900 1700 4150 2450 6600 3750 7350* 6950
(0') (5900) (3500) (6400) (3700) (9200) (5400) (14600) (8300) (16200) (15400)
–3.0 m 3800 2200 4100 2400 6500 3650 11150* 7050 9200* 9200*
(–9') (8400) (4900) (9100) (5300) (14400) (8100) (24500) (15600) (20300) (20300)
–4.5 m 4950* 3450 5550* 3850 8200* 7350
(–14') (11000) (7600) (12200) (8500) (18000) (16200)
Arm length 2900 mm (9'6")
7.5 m 1900* 1900*
(24') (4200) (4200)
6.0 m 1750* 1750* 3250* 2950
(19') (3800) (3800) (7200) (6500)
4.5 m 1700* 1700* 2250* 1850 3900* 2850
(14') (3800) (3800) (4900) (4100) (8600) (6300)
3.0 m 1800* 1550 3050 1800 4500 2700 5500* 4400 7850* 7850*
(9') (3900) (3400) (6700) (4000) (9900) (6000) (12200) (9700) (17300) (17300)
0m 2250* 1450 2850 1650 4100 2400 6600 3700 7650* 6950
(0') (5000) (3200) (6300) (3600) (9100) (5300) (14500) (8200) (16900) (15300)
–3.0 m 3450 1950 4050 2300 6400 3600 11500* 6900 8400* 8400*
(–9') (7600) (4400) (8900) (5100) (14200) (7900) (25300) (15300) (18500) (18500)
–4.5 m 4800* 2950 6050* 3700 8900* 7200
(–14') (10600) (6500) (13300) (8200) (19600) (15800)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC200-7
Conditions: Boom: 5700 mm (18'8"), Bucket (SAE): 0.80 m3 (1.05 cu.yd), Shoes: 600 mm (24") unit :kg (lb)
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2925 mm (9'7")
7.6 m *2500 *2500 *3500 *3500
(25') (5600) (5600) (7700) (7700)
6.1 m *2400 *2400 *3950 *3950
(20') (5300) (5300) (8700) (8700)
4.6 m *2400 2150 3950 2600 *4500 3900
(15') (5300) (4800) (8800) (5700) (9900) (8600)
3.0 m *2550 1950 3850 2500 *5350 3700 *6750 5850 *10450 *10450
(10') (5600) (4300) (8500) (5500) (11800) (8100) (14900) (12900) (23000) (23000)
1.5 m *2800 1850 3750 2350 5400 3450 *8550 5350 *6950 *6950
(5') (6200) (4100) (8300) (5200) (11900) (7600) (18900) (11800) (15300) (15300)
0m 3050 1900 3650 2300 5200 3250 8250 5050 *7400 *7400
(0') (6700) (4200) (8000) (5000) (11500) (7200) (18200) (11100) (16400) (16400)
–1.5 m 3350 2050 3600 2250 5100 3150 8100 4900 *10400 9500 *6300 *6300
(–5') (7400) (4600) (7900) (4900) (11200) (7000) (17900) (10800) (22900) (20900) (13900) (13900)
–3.0 m 4000 2500 5100 3150 8100 4950 *14350 9650 *9800 *9800
(–10') (8800) (5500) (11200) (7000) (17900) (10900) (31600) (21300) (21600) (21600)
–4.6 m 5650 3550 *8300 5100 *12000 10000
(–15') (12500) (7900) (18300) (11200) (26400) (22000)
Arm length 2410 mm (7'11")
7.6 m *4000 *4000
(25') (8800) (8800)
6.1 m *3750 3000 *4450 3950
(20') (8300) (6600) (9800) (8700)
4.6 m 3800 2450 3900 2500 *4950 3800 *5650 *5650
(15') (8400) (5400) (8600) (5600) (10900) (8400) (12500) (12500)
3.0 m 3400 2150 3800 2450 5600 3600 *7450 5700
(10') (7500) (4800) (8400) (5400) (12300) (8000) (16400) (12600)
1.5 m 3300 2050 3700 2350 5350 3400 8450 5250
(5') (7300) (4600) (8200) (5200) (11800) (7500) (18700) (11500)
0m 3400 2100 3650 2250 5150 3250 8150 4950 *6800 *6800
(0') (7500) (4700) (8000) (5000) (11400) (7100) (18000) (11000) (15000) (15000)
–1.5 m 3750 2350 5100 3150 8100 4900 *11400 9500 *7100 *7100
(–5') (8300) (5200) (11200) (7000) (17800) (10800) (25100) (21000) (15700) (15700)
–3.0 m 4650 2900 5150 3200 8200 4950 *13500 9750 *11750 *11750
(–10') (10200) (6400) (11400) (7100) (18000) (11000) (29800) (21500) (26000) (26000)
-4.6 m *6600 4550 *7400 5200 *10600 10150
(–15') (14500) (10000) (16300) (11500) (23400) (22400)
Arm length 1840 mm (6')
7.6 m *4450 *4450 *5050 *5050
(25') (9800) (9800) (11100) (11100)
6.1 m *4100 3450 *5000 3800 *5250 *5250
(20') (9100) (7600) (11100) (8300) (11600) (11600)
4.6 m 4150 2700 *5400 3700 *6400 6000 *9100 *9100
(15') (9200) (6000) (11900) (8100) (14100) (13200) (20100) (20100)
3.0 m 3750 2350 5450 3500 *8000 5350
(10') (8300) (5200) (12000) (7700) (17600) (11800)
1.5 m 3600 2250 3650 2300 5250 3300 8250 5000
(5') (8000) (5000) (8100) (5000) (11500) (7300) (18200) (11100)
0m 3750 2300 5100 3150 8050 4850
(0') (8200) (5100) (11200) (7000) (17700) (10700)
–1.5 m 4200 2650 5050 3150 8050 4850 *12400 9500
(–5') (9300) (5800) (11200) (6900) (17700) (10700) (27400) (21000)
–3.0 m 5500 3450 8200 5000 *12100 9800
(–10') (12100) (7600) (18100) (11000) (26700) (21600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J/ISO 10567. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2C-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2925 mm (9'7")
7.6 m *2750 *2750 *3800 *3800
(25') (6100) (6100) (8300) (8300)
6.1 m *2600 *2600 *4300 *4300
(20') (5800) (5800) (9500) (9500)
4.6 m *2650 2550 *4650 3000 *4900 4500
(15') (5800) (5600) (10300) (6600) (10800) (9900)
3.0 m *2800 2300 4750 2900 *5850 4250 *7350 6750 *11350 *11350
(10') (6100) (5100) (10500) (6400) (12900) (9400) (16200) (14900) (25000) (25000)
1.5 m *3050 2200 4650 2800 6700 4000 *9300 6250 *7500 *7500
(5') (6700) (4900) (10200) (6200) (14700) (8900) (20500) (13800) (16500) (16500)
0m *3500 2250 4550 2700 6450 3850 10450 5900 *8000 *8000
(0') (7800) (5000) (10000) (5900) (14300) (8400) (23000) (13000) (17700) (17700)
–1.5 m 4150 2450 4500 2650 6350 3750 *10250 5800 *11200 *11200 *6800 *6800
(–5') (9200) (5400) (9900) (5800) (14000) (8200) (22700) (12700) (24700) (24700) (15000) (15000)
–3.0 m 4950 2950 6350 3750 10300 5800 *15600 11500 *10550 *10550
(–10') (11000) (6500) (14000) (8200) (22700) (12800) (34400) (25400) (23200) (23200)
–4.6 m *6750 4150 *9050 6000 *13050 11900
(–15') (14900) (9200) (20000) (13200) (28800) (26200)
Arm length 2410 mm (7'11")
7.6 m *4300 *4300
(25') (9500) (9500)
6.1 m *4100 3500 *4850 4500
(20') (9000) (7700) (10700) (10000)
4.6 m *4150 2850 *4700 2950 *5400 4400 *6200 *6200
(15') (9100) (6300) (10400) (6500) (11900) (9700) (13600) (13600)
3.0 m *4250 2550 4700 2850 *6300 4200 *8100 6600
(10') (9300) (5600) (10400) (6300) (13900) (9200) (17800) (14600)
1.5 m 4100 2450 4600 2750 *6600 3950 *9850 6100
(5') (9000) (5400) (10200) (6100) (14500) (8700) (21800) (13500)
0m 4200 2500 4550 2700 6450 3800 10350 5850 *7350 *7350
(0') (9300) (5500) (10000) (5900) (14200) (8400) (22800) (12900) (16200) (16200)
–1.5 m 4650 2750 6350 3750 10250 5800 *12250 11400 *7650 *7650
(–5') (10300) (6100) (14000) (8300) (22600) (12700) (27000) (25100) (16900) (16900)
–3.0 m 5750 3450 6400 3800 *10250 5850 *14700 11600 *12650 *12650
(–10') (12700) (7600) (14200) (8400) (22600) (12900) (32400) (25600) (27900) (27900)
–4.6 m *7200 5300 *8100 6100 *11600 *11600
(–15') (15900) (11700) (17800) (13500) (25500) (25500)
Arm length 1840 mm (6')
7.6 m *4800 *4800 *5500 *5500
(25') (10600) (10600) (12100) (12100)
6.1 m *4550 3950 *5450 4350 *5700 *5700
(20') (9900) (8800) (12100) (9600) (12600) (12600)
4.6 m *4500 3150 *5900 4250 *7000 6900 *9850 *9850
(15') (9900) (7000) (13000) (9400) (15400) (15200) (21800) (21800)
3.0 m *4650 2800 *6700 4050 *8700 6250
(10') (10200) (6200) (14800) (9000) (19200) (13700)
1.5 m 4500 2650 4550 2700 6500 3850 *10350 5900
(5') (9900) (5900) (10000) (6000) (14300) (8500) (22800) (13000)
0m 4650 2750 6350 3750 10200 5700
(0') (10300) (6100) (14000) (8200) (22500) (12600)
–1.5 m 5250 3100 6350 3700 10200 5700 *13350 11350
(–5') (11600) (6900) (14000) (8200) (22500) (12600) (29400) (25100)
–3.0 m 6850 4050 *9550 5900 *13200 11700
(–10') (15100) (8900) (21100) (13000) (29100) (25800)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J/ISO 10567. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2C-24
AH_25.book Page 25 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC200LC-7
Conditions: Boom: 5700 mm (18'8"), Bucket (SAE): 0.80 m3 (1.05 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2925 mm (9'7")
7.6 m *2500 *2500 *3500 *3500
(25') (5600) (5600) (7700) (7700)
6.1 m *2400 *2400 *3950 *3950
(20') (5300) (5300) (8700) (8700)
4.6 m *2400 *2400 *4300 3000 *4500 4500
(15') (5300) (5300) (9400) (6600) (9900) (9900)
3.0 m *2550 2300 *4700 2900 *5350 4250 *6750 *6750 *10450 *10450
(10') (5600) (5100) (10300) (6400) (11800) (9400) (14900) (14900) (23000) (23000)
1.5 m *2800 2200 4650 2800 *6300 4000 *8550 6250 *6950 *6950
(5') (6200) (4900) (10200) (6200) (13900) (8900) (18900) (13800) (15300) (15300)
0m *3250 2250 4550 2700 6450 3850 *9750 5900 *7400 *7400
(0') (7100) (5000) (10000) (5900) (14300) (8400) (21500) (13000) (16400) (16400)
–1.5 m *4000 2450 4500 2650 6350 3750 *10100 5800 *10400 *10400 *6300 *6300
(–5') (8800) (5400) (9900) (5800) (14000) (8200) (22300) (12700) (22900) (22900) (13900) (13900)
–3.0 m 4950 2950 6350 3750 *9750 5800 *14350 11500 *9800 *9800
(–10') (11000) (6500) (14000) (8200) (21500) (12800) (31600) (25400) (21600) (21600)
–4.6 m *6150 4150 *8300 6000 *12000 11900
(–15') (13600) (9200) (18300) (13200) (26400) (26000)
Arm length 2410 mm (7'11")
7.6 m *4000 *4000
(25') (8800) (8800)
6.1 m *3750 3500 *4450 *4450
(20') (8300) (7700) (9800) (9800)
4.6 m *3800 2850 *4350 2950 *4950 4400 *5650 *5650
(15') (8000) (6300) (9600) (6500) (10900) (9700) (12500) (12500)
3.0 m *4050 2550 4700 2850 *5750 4200 *7450 6600
(10') (8900) (5600) (10400) (6300) (12700) (9200) (16400) (14600)
1.5 m 4100 2450 4600 2750 *6600 3950 *9050 6100
(5') (9000) (5400) (10200) (6100) (14500) (8700) (20000) (13500)
0m 4200 2500 4550 2700 6450 3800 *9950 5850 *6800 *6800
(0') (9300) (5500) (10000) (5900) (14200) (8400) (22000) (12900) (15000) (15000)
–1.5 m 4650 2750 6350 3750 *10100 5800 *11400 *11400 *7100 *7100
(–5') (10300) (7600) (14000) (8300) (22200) (12900) (25100) (25100) (15700) (15700)
–3.0 m 5750 3450 6400 3800 *9400 5850 *13500 11600 *11750 *11750
(–10') (12100) (7600) (14200) (8400) (20700) (12900) (29800) (25600) (26000) (26000)
–4.6 m *6600 5300 *7400 6100 *10600 *10600
(–15') (14500) (11700) (16300) (13500) (23400) (23400)
Arm length 1840 mm (6')
7.6 m *4450 *4450 *5050 *5050
(25') (9800) (9800) (11100) (11100)
6.1 m *4100 3950 *5000 4350 *5250 *5250
(20') (9100) (8800) (11100) (9600) (11600) (11600)
4.6 m *4150 3150 *5400 4250 *6400 *6400 *9100 *9100
(15') (9200) (7000) (11900) (9400) (14100) (14100) (20100) (20100)
3.0 m *4400 2800 *6150 4050 *8000 6250
(10') (9700) (6200) (13500) (9000) (17600) (13700)
1.5 m 4500 2650 4550 2700 6500 3850 *9500 5900
(5') (9900) (5900) (10000) (6000) (14300) (8500) (20900) (13000)
0m 4650 2750 6350 3750 *10050 5700
(0') (10300) (6100) (14000) (8200) (22100) (12600)
–1.5 m 5250 3100 6350 3700 *9800 5700 *12400 11350
(–5') (11600) (6900) (14000) (8200) (21600) (12600) (27400) (25100)
–3.0 m *6500 4050 *8750 5900 *12100 11700
(–10') (14400) (8900) (19300) (13000) (26700) (25800)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J/ISO 10567. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2C-25
AH_25.book Page 26 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-26
AH_25.book Page 27 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
Conditions: Boom: 5700 mm (18'8"), Bucket (SAE): 0.80 m3 (1.05 cu.yd), Shoes:800 mm (31.5") unit: kg (lb)
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2925 mm (9'7")
7.6 m *2750 *2750 *3800 *3800
(25') (6100) (6100) (8300) (8300)
6.1 m *2600 *2600 *5200 *4700
(20') (5800) (5800) (11500) (10300)
4.6 m *2650 2600 4650 3050 *6000 4550
(15') (5800) (5700) (10250) (6700) (13300) (10000)
3.0 m *2800 2350 4850 2950 *7050 4300 *8900 6850 *13650 *13450
(10') (6100) (5100) (10700) (6500) (15500) (9500) (19700) (15100) (30100) (29700)
1.5 m *3050 2250 4700 2800 6750 4050 11000 6300 *7500 *7500
(5') (6700) (4900) (10400) (6200) (14900) (9000) (24200) (13900) (16500) (16500)
0m 3500 2250 4600 2750 6550 3850 10550 5950 *8000 *8000
(0') (7800) (4900) (10100) (6000) (14500) (8500) (23300) (13200) (17700) (17700)
–1.5 m 4200 2500 4550 2700 6450 3750 10400 5850 *11200 11200 *6800 *6800
(–5') (9300) (5500) (10000) (5900) (14200) (8300) (22900) (12900) (24700) (24700) (15000) (15000)
–3.0 m 5050 3000 6450 3800 10450 5850 *16050 11600 *10550 *10550
(–10') (11100) (6600) (14200) (8350) (23000) (12900) (35400) (25600) (23200) (23200)
–4.6 m 7150 4200 10650 6050 *15800 12000
(–15') (15800) (9300) (23500) (13300) (34900) (26400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-27
AH_25.book Page 28 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-28
AH_25.book Page 29 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-29
AH_25.book Page 30 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-30
AH_25.book Page 31 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC220-7
Conditions: Boom: 5850 mm (19'2"), Bucket (SAE): 1.0 m3 (1.31 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3045 mm (10'0")
7.6 m *2900 *2900 *3900 *3900
(25') (6400) (6400) (8700) (8700)
6.1 m *2750 *2750 *3700 3500 *4100 *4100
(20') (6100) (6100) (8200) (7800) (9000) (9000)
4.6 m *2800 2750 *4600 3450 *4800 *4800
(15') (6200) (6000) (10100) (7600) (10600) (10600)
3.0 m *2950 2450 4900 3350 *5900 4900 *7450 *7450 *11800 *11800
(10') (6500) (5500) (10800) (7400) (13000) (10800) (17900) (17900) (26000) (26000)
1.5 m *3250 2350 4750 3200 6850 4600 *9700 7150 *6850 *6850
(5') (7200) (5200) (10400) (7000) (15100) (10100) (21400) (15700) (15100) (15100)
0m 3650 2400 4600 3050 6550 4350 10500 6700 *7800 *7800
(0') (8100) (5300) (10100) (6700) (14500) (9600) (23200) (14800) (17100) (17100)
–1.5 m 4000 2600 4550 3000 6450 4200 10300 6550 *11150 *11150 *6900 *6900
(–5') (8800) (5800) (10000) (6600) (14200) (9300) (22700) (14400) (24600) (24600) (15200) (15200)
–3.0 m 4700 3100 6400 4200 10350 6550 *16050 13100 *10750 *10750
(–10') (10400) (6900) (14200) (9300) (22800) (14500) (35400) (28900) (23700) (23700)
–4.6 m 6500 4300 6600 4350 *10400 6750 *15200 13500
(–15') (14300) (9500) (14500) (9600) (23000) (14900) (33500) (29800)
Arm length 2500 mm (8'2")
7.6 m *4600 *4600 *4650 *4650
(25') (10100) (10100) (10200) (10200)
6.1 m *4400 3750 *4650 *4650
(20') (9700) (8300) (10300) (10300)
4.6 m *4450 3100 4950 3350 *5350 5050 *6100 *6100
(15') (9800) (6800) (10900) (7400) (11700) (11100) (13500) (13500)
3.0 m 4100 2750 4800 3250 *6350 4750 8250 7500
(10') (9100) (6100) (10600) (7200) (14000) (10500) (18200) (16600)
1.5 m 3950 2600 4650 3100 6700 4450 *10300 6900
(5') (8700) (5800) (10300) (6900) (14800) (9900) (22700) (15200)
0m 4050 2700 4550 3000 6450 4250 10300 6550 *7250 *7250
(0') (9000) (5900) (10000) (6600) (14300) (9400) (22800) (14500) (16000) (16000)
–1.5 m 4500 2950 4500 3000 6400 4200 10200 6450 *12450 *12450 *8000 *8000
(–5') (9900) (6500) (10000) (6600) (14100) (9200) (22500) (14300) (27400) (27400) (17700) (17700)
–3.0 m 5500 3650 6450 4250 10350 6550 *16450 13100 *13150 *13150
(–10') (12100) (8000) (14200) (9300) (22800) (14500) (36300) (28900) (29000) (29000)
–4.6 m *8000 5500 *9350 6650 *13700 13650
(–15') (17600) (12100) (20600) (14700) (30200) (30100)
Arm length 2000 mm (6'7")
7.6 m *4750 *4750
(25') (10500) (10500)
6.1 m *4500 4100 *5200 5100
(20') (9900) (9100) (11400) (11300)
4.6 m *4550 3300 *5800 4950 *6850 *6850 *9750 *9750
(15') (10000) (7300) (12800) (10900) (15100) (15100) (21500) (21500)
3.0 m 4400 2950 4750 3200 *6750 4650 *8850 7100
(10') (9700) (6500) (10400) (7000) (14900) (10300) (19500) (15700)
1.5 m 4250 2800 4600 3050 6600 4400 10500 6700
(5') (9400) (6200) (10200) (6800) (14600) (9700) (23100) (14800)
0m 4400 2900 4550 3000 6400 4200 10200 6450
(0') (9700) (6400) (10000) (6600) (14200) (9300) (22500) (14200)
–1.5 m 4900 3250 6350 4150 10200 6450 *13000 12900
(–5') (10800) (7100) (14100) (9200) (22500) (14200) (28600) (28400)
–3.0 m 6200 4100 6500 4300 10400 6600 *15350 13250
(–10') (13700) (9100) (14300) (9400) (22900) (14600) (33900) (29200)
–4.6 m *8150 6800 *8350 7700
(–15') (17900) (15000) (18400) (15500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-31
AH_25.book Page 32 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-32
AH_25.book Page 33 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC220LC-7
Conditions: Boom: 5850 mm (19'2"), Bucket (SAE): 1.0 m3 (1.31 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3045 mm (10'0")
7.6 m *2900 *2900 *3900 *3900
(25') (6400) (6400) (8700) (8700)
6.1 m *2750 *2750 *3700 *3700 *4100 *4100
(20') (6100) (6100) (8200) (8200) (9000) (9000)
4.6 m *2800 *2800 *4600 4000 *4800 *4800
(15') (6200) (6200) (10100) (8800) (10600) (10600)
3.0 m *2950 2900 *5150 3850 *5900 5650 *7450 *7450 *11800 *11800
(10') (6500) (6400) (11400) (8500) (13000) (12400) (16500) (16500) (26000) (26000)
1.5 m *3250 2800 *5800 3700 *7050 5350 *9700 8300 *6850 *6850
(5') (7200) (6200) (12800) (8200) (15500) (11700) (21400) (18300) (15100) (15100)
0m *3750 2850 5650 3600 *8000 5100 *11200 7900 *7800 *7800
(0') (8300) (6300) (12500) (7900) (17600) (11200) (24700) (17400) (17100) (17100)
–1.5 m *4600 3100 5600 3500 7950 4950 *11800 7700 *11150 11150 *6900 *6900
(–5') (10100) (6800) (12300) (7800) (17500) (10900) (26100) (17000) (24600) (24600) (15200) (15200)
–3.0 m 5800 3650 7950 4950 *11650 7750 *16050 15700 *10750 *10750
(–10') (12800) (8100) (17500) (10900) (25700) (17000) (35400) (34600) (23700) (23700)
–4.6 m *7250 5050 *7400 5100 *10400 7950 *15200 *15200
(–15') (16000) (11100) (16300) (1130) (23000) (17500) (33500) (33500)
Arm length 2500 mm (8'2")
7.6 m *4600 *4600 *4650 *4650
(25') (10100) (10100) (10200) (10200)
6.1 m *4400 4350 *4650 *4650
(20') (9700) (9600) (10300) (10300)
4.6 m *4450 3600 *5000 3900 *5350 *5350 *6100 *6100
(15') (9800) (7900) (11100) (8600) (11700) (11700) (13500) (13500)
3.0 m *4750 3250 *5500 3800 *6350 5500 *8250 *8250
(10') (10500) (7100) (12100) (8400) (14000) (12100) (18200) (18200)
1.5 m 4850 3100 5700 3650 *7400 5200 *10300 8050
(5') (10800) (5800) (12600) (8000) (16300) (11500) (22700) (17800)
0m 5000 3150 5600 3550 8000 5000 *11450 7700 *7250 *7250
(0') (11100) (7000) (12400) (7800) (17600) (11000) (25300) (17000) (16000) (16000)
–1.5 m 5550 3500 5550 3500 7900 4900 *11800 7650 *12450 *12450 *8000 *8000
(–5') (12200) (7700) (12300) (7700) (17400) (10800) (26000) (16800) (27400) (27400) (17700) (17700)
–3.0 m 6800 4250 7950 4950 *11250 7700 *16450 15700 *13150 *13150
(–10') (14900) (9400) (17600) (10900) (24900) (17000) (36300) (34700) (29000) (29000)
–4.6 m *8000 6400 *9350 7800 *13700 *13700
(–15') (17600) (14100) (20600) (17200) (30200) (30200)
Arm length 2000 mm (6'7")
7.6 m *4750 *4750
(25') (10500) (10500)
6.1 m *4500 *4500 *5200 *5200
(20') (9900) (9900) (11400) (11400)
4.6 m *4550 3850 *5800 5700 *6850 *6850 *9750 *9750
(15') (10000) (8500) (12800) (12500) (15100) (15100) (21500) (21500)
3.0 m *4800 3450 *5800 3700 *6750 5400 *8850 8300
(10') (10600) (7600) (12800) (8200) (14900) (11900) (19500) (18300)
1.5 m 5200 3300 5650 3600 *7700 5100 *10800 7850
(5') (11500) (7300) (12500) (7900) (17000) (11300) (23800) (17300)
0m 5400 3400 5600 3500 7950 4950 *11650 7600
(0') (11900) (7500) (12300) (7700) (17500) (10900) (25700) (16800)
–1.5 m 6050 3800 7900 4900 *11650 7600 *13000 *13000
(–5') (13300) (8400) (17400) (10800) (25700) (16800) (28600) (28600)
–3.0 m *7550 4800 7850 5000 *10850 7750 *15350 *15350
(–10') (16600) (10600) (17300) (11100) (23900) (17100) (33900) (33900)
–4.6 m *8150 7950 *8350 8200
(–15') (17900) (17500) (18400) (18000)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-33
AH_25.book Page 34 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-34
AH_25.book Page 35 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-35
AH_25.book Page 36 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC228US-3
Conditions: Boom: 5700 mm (18'8"), Bucket (SAE): 0.80 m3 (1.05 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2925 mm (9'7")
6.0 m 2700* 2350 3250* 2450 3950* 3800
(20') (6000) (5150) (7200) (5400) (8750) (8450)
4.5 m 2750* 1950 3950 2450 4650* 3700 5000* 5000*
(15') (6050) (4300) (8700) (5400) (10200) (8150) (11000) (11000)
3m 2900* 1750 3850 2350 5600* 3500 7100* 5600 11050* 10700
(10') (6400) (3850) (5450) (5150) (12450) (7700) (15650) (12350) (24350) (23650)
1.5 m 2900 1700 3750 2250 5400 3250 8550 5100 6850* 6850*
(5') (6400) (3750) (8250) (4950) (11850) (7150) (18800) (11200) (15050) (15050)
0m 2950 1700 3650 2150 5200 3050 8250 4750 7650* 7650*
(0') (6500) (3750) (8050) (4700) (11450) (6700) (18150) (10450) (16900) (16900)
–1.5 m 3250 1850 3600 2100 5050 2950 8100 4650 10800* 9000 6700* 6700*
(–5') (7150) (4050) (7900) (4600) (11100) (6500) (17850) (10250) (23750) (19800) (14750) (14750)
–3.0 m 3850 2250 5100 2950 8100 4650 15550* 9150 10300* 10300*
(–10') (8450) (4950) (11200) (6500) (17850) (10250) (34250) (20150) (22650) (22650)
–4.5 m 5350 3200 8300 4800 14500* 9500
(–15') (11750) (7050) (18250) (10550) (31900) (20900)
PC228USLC-3
Conditions: Boom: 5700 mm (18'8"), Bucket (SAE): 0.80 m3 (1.05 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2925 mm (9'7")
6.0 m 2700* 2700* 3250* 2950 3950* 3950*
(20') (6000) (6000) (7200) (6500) (8750) (8750)
4.5 m 2750* 2400 4500* 2900 4650* 4300 5000* 5000*
(15') (6050) (5250) (9900) (6350) (10200) (9450) (11000) (11000)
3m 2900* 2150 4850 2800 5650* 4150 7100* 6500 11050* 11050*
(10') (6400) (4700) (10700) (6150) (12500) (9150) (15650) (14400) (24350) (24350)
1.5 m 3150* 2050 4750 2700 6750* 3900 9200* 6050 6850* 6850*
(5') (6900) (4500) (10450) (6000) (14850) (8550) (20250) (13300) (15050) (15050)
0m 3650* 2100 4600 2600 6600 3700 10600 5700 7650* 7650*
(0') (8050) (4600) (10100) (5700) (14550) (8150) (23400) (12550) (16900) (16900)
–1.5 m 4100 2300 4550 2550 6500 3600 10450 5600 10800* 10800* 6700* 6700*
(–5') (9000) (5050) (10000) (5600) (14300) (7900) (23100) (12300) (23750) (23750) (14750) (14750)
–3.0 m 4900 2750 6500 3600 10450 5600 15550* 11200 10300* 10300*
(–10') (10800) (6050) (14300) (7900) (23100) (12300) (34250) (24650) (22650) (22650)
–4.5 m 6800 3850 9950* 5800 14500* 11550
(–15') (14950) (8450) (21900) (12750) (31900) (25400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-36
AH_25.book Page 37 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC230NHD-7
Conditions:
One piece boom: 5700 mm (18'8"), Bucket (SAE): 0.96 m3 (1.26 cu.yd), Shoes: 550 mm (22") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
6.0 m 2650* 2650* 3550* 2900 4300* 4300*
(20') (5800) (5800) (7800) (6400) (9400) (9400)
4.5 m 2650* 2250 4650* 2850 4900* 4250 5500* 5500*
(15') (5800) (4900) (10200) (6200) (10800) (9300) (12100) (12100)
3.0 m 2800* 2050 4900 2700 5850* 3950 7400* 6200 11550* 11550*
(10') (6100) (4500) (10800) (5900) (12800) (8700) (16300) (13600) (25400) (25400)
1.5 m 3050* 1950 4750 2600 6800 3700 9300* 5650 6400* 6400*
(5') (6700) (4300) (10400) (5700) (14900) (8100) (20400) (12400) (14100) (14100)
0m 3450* 2000 4650 2450 6550 3450 10450 5250 7300* 7300*
(0') (7600) (4400) (10200) (5400) (14400) (7600) (23000) (11500) (16000) (16000)
–1.5 m 4100 2150 4600 2400 6450 3350 10250 5150 10550* 9650 6400* 6400*
(–5') (9000) (4700) (10100) (5300) (14200) (7300) (22500) (11300) (23200) (21200) (14100) (14100)
–3.0 m 4850 2550 6450 3400 10300 5150 15400* 9850 10150* 10150*
(–10') (10600) (5600) (14200) (7500) (22600) (11300) (33900) (21600) (22300) (22300)
–4.5 m 6350* 3550 9050 5350 13000* 10250
(–15') (13900) (7800) (19900) (11700) (28600) (22500)
Arm length 2400 mm (7'10")
6.0 m 4150* 3100 4900* 4350
(20') (9100) (6800) (10800) (9500)
4.5 m 4150* 2550 5000 2800 5450* 4200 6300* 6300*
(15') (9100) (5600) (11000) (6100) (12000) (9200) (13800) (13800)
3.0 m 4200 2300 4900 2750 6350* 3950 8250* 6100
(10') (9200) (5000) (10800) (6000) (13900) (8700) (18100) (13400)
1.5 m 4100 2200 4800 2600 6800 3700 10000* 5600
(5') (9000) (4800) (10500) (5700) (14900) (8100) (22000) (12300)
0m 4200 2250 4700 2550 6600 3550 10500 5300
(0') (9200) (4900) (10300) (5600) (14500) (7800) (23100) (11600)
–1.5 m 4600 2500 4650 2500 6550 3450 10400 5250 11250* 9900 6900* 6900*
(–5') (10100) (5500) (10200) (5500) (14500) (9600) (22900) (9300) (24700) (21800) (15200) (15200)
–3.0 m 5600 3050 6600 3500 10300* 5350 14700* 10150 12000* 12000*
(–10') (12300) (6700) (14500) (7700) (22600) (11700) (32300) (22300) (26400) (26400)
–4.5 m 6750* 4500 8250* 5600 11700* 10600
(–15') (14800) (9900) (18100) (12300) (25700) (23300)
Arm length 1800 mm (5'11")
6.0 m 4600* 3550 5500* 4200 5850* 5850*
(20') (10100) (7800) (12100) (9200) (12800) (12800)
4.5 m 4600* 2850 6000* 4100 7150* 6450 10200* 10200*
(15') (10100) (6200) (13200) (9000) (15700) (14200) (22400) (22400)
3.0 m 4650 2550 4850 2650 6800* 3850 9000* 5850
(10') (10200) (5600) (10600) (5800) (14900) (8400) (19800) (12800)
1.5 m 4500 2450 4750 2600 6700 3650 10450* 5400
(5') (9900) (5400) (10400) (5700) (14700) (8000) (23000) (11900)
0m 4650 2500 4700 2550 6550 3500 10350 5200
(0') (10200) (5500) (10300) (5600) (14400) (7700) (22700) (11400)
–1.5 m 5250 2800 6550 3450 10350 5200 12250* 9950
(–5') (11500) (6100) (14400) (7600) (22700) (11400) (26900) (21900)
–3.0 m 6650 3600 6700 3600 9650* 5400 13200* 10250
(–10') (14600) (7900) (14700) (7900) (21200) (11900) (29000) (22500)
–4.5 m
(–15')
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-37
AH_25.book Page 38 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC230NHD-7
Conditions:
Two piece boom: 5500 mm (18'1"), Bucket (SAE): 0.96 m3 (1.26 cu.yd), Shoes: 550 mm (22") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
6.0 m 2900* 2500 4300* 2900 4350* 4350*
(20') (6400) (5500) (9400) (6400) (9500) (9500)
4.5 m 2850* 2100 4550* 2800 4950* 4250
(15') (6200) (4600) (10000) (6100) (10900) (9300)
3.0 m 3000* 1900 4950 2700 5850* 3950 7600* 6250
(10') (6600) (4200) (10900) (5900) (12800) (8700) (16700) (13700)
1.5 m 3200* 1800 4800 2550 6800* 3700 9350* 5650
(5') (7000) (3900) (10500) (5600) (14900) (8100) (20500) (12400)
0m 3600* 1850 4650 2450 6600 3500 10500* 5300 6450* 6450*
(0') (7900) (4000) (10200) (5400) (14500) (7700) (23100) (11600) (14200) (14200)
–1.5 m 3900 2050 4600 2400 6500 3400 10400 5200 10000* 9950*
(–5') (8600) (4500) (10100) (5300) (14300) (7500) (22900) (11400) (22000) (21900)
–3.0 m 4650 2450 6500 3400 10450 5250
(–10') (10200) (5400) (14300) (7500) (23000) (11500)
Arm length 2400 mm (7'10")
6.0 m 4850* 2900 4900* 4400
(20') (10600) (6400) (10800) (9700)
4.5 m 4400 2400 5000* 2850 5500* 4200 6600* 6600*
(15') (9700) (5300) (11000) (6200) (12100) (9200) (14500) (14500)
3.0 m 4050 2200 4950 2750 6350* 3950 8400* 6150
(10') (8900) (4800) (10900) (6000) (13900) (8700) (18500) (13500)
1.5 m 3950 2100 4850 2650 6900 3750 10050* 5650
(5') (8700) (4600) (10600) (5800) (15200) (8200) (22100) (12400)
0m 4050 2150 4750 2550 6700 3550 10650 5400
(0') (8900) (4700) (10400) (5600) (14700) (7800) (23400) (11900)
–1.5 m 4450 2400 4750 2550 6550 3500 10600 5350
(–5') (9800) (5300) (10400) (5600) (14400) (7700) (23300) (11700)
–3.0 m 6700 3550
(–10') (14700) (7800)
Arm length 1800 mm (5'11")
6.0 m 4950* 3350 5450* 4250
(20') (10900) (7300) (12000) (9300)
4.5 m 4900* 2750 5000 2750 6000* 4100 7400* 6550
(15') (10800) (6000) (11000) (6000) (13200) (9000) (16300) (14400)
3.0 m 4500 2450 4900 2700 6800* 3900 9200* 5950
(10') (9900) (5400) (10800) (5900) (14900) (8600) (20200) (13100)
1.5 m 4400 2350 4800 2600 6850 3700 10550* 5500
(5') (9700) (5100) (10500) (5700) (15000) (8100) (23200) (12100)
0m 4550 2450 4750 2550 6700 3550 10600 5400
(0') (10000) (5400) (10400) (5600) (14700) (7800) (23300) (11900)
–1.5 m 5100 2750 6650 3550 10650 5400
(–5') (11200) (6000) (14600) (7800) (23400) (11900)
–3.0 m
(–10')
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-38
AH_25.book Page 39 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC240LC-7
Conditions: Boom: 5850 mm (19'2"), Bucket (SAE): 1.01 m3 (1.32 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3000 mm (9'10")
6.0 m *3000 *3000 *4450 4250 *4900 *4900
(20') (6600) (6600) (9800) (9400) (10800) (10800)
4.5 m *3050 *3050 *5550 4200 *5800 *5800
(15') (6700) (6700) (12200) (9200) (12800) (12800)
3.0 m *3200 2950 *6250 4050 *7150 5900 *9050 *9050 *14450 *14450
(10') (7100) (6500) (13700) (8900) (15700) (13000) (20000) (20000) (31800) (31800)
1.5 m *3550 2850 6050 3850 *8550 5550 *11700 8650 *6900 *6900
(5') (7800) (6200) (13300) (8500) (18800) (12200) (25800) (19000) (15200) (15200)
0m *4050 2900 5900 3700 8450 5250 *13500 8150 *8100 *8100
(0') (8900) (6400) (13000) (8200) (18600) (11600) (29700) (18000) (17900) (17900)
–1.5 m *4950 3100 5800 3650 8300 5150 13550 8000 *11650 *11650 *7350 *7350
(–5') (10900) (6900) (12800) (8000) (18300) (11300) (29900) (17600) (25700) (25700) (16200) (16200)
–3.0 m 5850 3700 8250 5100 13600 8000 *16750 16350 *11350 *11350
(–10') (12900) (8100) (18200) (11300) (30000) (17700) (37000) (36100) (25100) (25100)
–4.5 m 7950 5000 8450 5300 *12650 8200 *18350 16850
(–15') (17600) (11000) (18600) (11500) (27900) (18100) (40500) (37100)
Arm length 3500 mm (11'6")
6.0 m *2350 *2350 *4050 *4050
(20') (5200) (5200) (9000) (9000)
4.5 m *2400 *2400 *5050 4200 *5200 *5200
(15') (5300) (5300) (11200) (9300) (11500) (11500)
3.0 m *2550 *2550 *5800 4050 *6550 5950 *8050 *8050 *11850 *11850
(10') (5600) (5600) (12800) (8900) (14400) (13100) (17800) (17800) (26100) (26100)
1.5 m *2850 2650 6050 3850 *8000 5550 *10850 8750 *10850 *10850
(5') (6200) (5800) (13300) (8500) (17600) (12200) (24000) (19300) (23900) (23900)
0m *3300 2650 5850 3700 8400 5250 *12900 8150 *9500 *9500 *4300 *4300
(0') (7300) (5900) (12900) (8100) (18600) (11600) (28500) (18000) (20900) (20900) (9400) (9400)
–1.5 m *4050 2850 5750 3600 8150 5000 13500 7900 *11850 *11850 *7350 *7350
(–5') (8900) (6300) (12600) (7900) (18000) (11000) (29700) (17400) (26100) (26100) (16200) (16200)
–3.0 m 5350 3350 5700 3550 8150 5000 13450 7850 *15650 *15650 *10600 *10600
(–10') (11800) (7400) (12600) (7900) (18000) (11100) (29700) (17400) (34500) (34500) (23300) (23300)
–4.5 m 7050 4400 8250 5100 *13100 8000 *19350 16500 *14400 *14400
(–15') (15500) (9700) (18200) (11300) (28900) (17700) (42600) (36300) (31800) (31800)
Arm length 2500 mm (8'2")
6.0 m *4750 4400 *5650 *5650
(20') (10500) (9700) (12500) (12500)
4.5 m *4850 3650 *6100 4150 *6500 6100 *7500 *7500
(15') (10700) (8100) (13500) (9100) (14300) (13500) (16500) (16500)
3.0 m 5150 3300 6200 4000 *7750 5800 *10150 9100
(10') (11400) (7300) (13600) (8800) (17100) (12800) (22300) (20100)
1.5 m 5000 3200 6000 3850 8650 5450 *12550 8450
(5') (11000) (7000) (13300) (8500) (19100) (12100) (27700) (18600)
0m 5150 3250 5900 3750 8400 5250 13700 8100
(0') (11300) (7200) (13000) (8200) (18500) (11600) (30200) (17800)
–1.5 m 5650 3550 5850 3700 8300 5150 13600 8000 *13000 *13000 *8550 *8550
(–5') (12500) (7900) (12900) (8100) (18300) (11400) (29900) (17600) (28700) (28700) (18800) (18800)
–3.0 m 6850 4350 8350 5200 *13700 8100 *19850 16550 *13900 *13900
(–10') (15200) (9600) (18400) (11500) (30200) (17900) (43800) (36500) (30700) (30700)
–4.5 m *9550 6400 *11700 8400 *16750 *16750
(–15') (21000) (14100) (25800) (18500) (36900) (36900)
Arm length 2000 mm (6'7")
6.0 m *4850 4800 *6300 6200
(20') (10700) (10600) (13900) (13600)
4.5 m *4950 3950 *5600 4050 *7100 6000 *8400 *8400 *12000 *12000
(15') (10900) (8700) (12400) (8900) (15600) (13200) (18600) (18600) (26500) (26500)
3.0 m *5250 3550 6100 3950 *8250 5700 *11050 8850
(10') (11600) (7800) (13500) (8700) (18200) (12500) (24300) (19600)
1.5 m 5350 3400 5950 3800 8550 5400 *13200 8250
(5') (11800) (7500) (13200) (8400) (18900) (11900) (29100) (18200)
0m 5550 3500 5900 3700 8350 5200 13600 8000
(0') (12200) (7700) (13000) (8200) (18400) (11500) (30000) (17700)
–1.5 m 6200 3900 8300 5150 13600 8000 *13550 *13550
(–5') (13600) (8600) (18300) (11400) (30000) (17700) (29900) (29900)
–3.0 m 7800 4900 8450 5250 *13200 8150 *18650 16750
(–10') (17200) (10800) (18600) (11600) (29100) (18000) (41100) (36900)
–4.5 m *9750 7850 *10450 8550
(–15') (21500) (17300) (23100) (18900)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-39
AH_25.book Page 40 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC240NLC-7
Conditions: Boom: 5850 mm (19'2"), Bucket (SAE): 1.01 m3 (1.32 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3000 mm (9'10")
6.0 m *3000 *3000 *4450 3750 *4900 *4900
(20') (6600) (6600) (9800) (8300) (10800) (10800)
4.5 m *3050 2800 *5550 3700 *5800 5500
(15') (6700) (6200) (12200) (8100) (12800) (12100)
3.0 m *3200 2550 5600 3550 *7150 5150 *9050 8200 *14450 *14450
(10') (7100) (5600) (12300) (7800) (15700) (11400) (20000) (18100) (31800) (31800)
1.5 m *3550 2450 5400 3350 7800 4850 *11700 7500 *6900 *6900
(5') (7800) (5400) (11900) (7400) (17200) (10700) (25800) (16500) (15200) (15200)
0m *4050 2450 5250 3200 7500 4550 12150 7050 *8100 *8100
(0') (8900) (5500) (11600) (7100) (16500) (10100) (26800) (15600) (17900) (17900)
–1.5 m 4400 2700 5150 3150 7350 4450 11950 6900 *11650 *11650 *7350 *7350
(–5') (9700) (5900) (11400) (6900) (16200) (9800) (26300) (15200) (25700) (25700) (16200) (16200)
–3.0 m 5200 3200 7350 4450 11950 6900 *16750 13800 *11350 *11350
(–10') (11500) (7000) (16200) (9800) (26400) (15200) (37000) (30500) (25100) (25100)
–4.5 m 7100 4350 7500 4600 12200 7100 *18350 14250
(–15') (15600) (9600) (16600) (10100) (25900) (15700) (40500) (31400)
Arm length 3500 mm (11'6")
6.0 m *2350 *2350 *4050 3800
(20') (5200) (5200) (9000) (8400)
4.5 m *2400 *2400 *5050 3700 *5200 *5200
(15') (5300) (5300) (11200) (8200) (11500) (11500)
3.0 m *2550 2350 5600 3550 *6550 5200 *8050 *8050 *11850 *11850
(10') (5600) (5200) (12300) (7800) (14400) (11500) (17800) (17800) (26100) (26100)
1.5 m *2850 2250 5400 3350 7850 4850 *10850 7600 *10850 *10850
(5') (6200) (5000) (11900) (7400) (17300) (10700) (24000) (16800) (23900) (23900)
0m *3300 2300 5200 3150 7500 4550 12150 7050 *9500 *9500 *4300 *4300
(0') (7300) (5000) (11500) (7000) (16500) (10000) (26800) (15500) (20900) (20900) (9400) (9400)
–1.5 m *4050 2450 5100 3050 7200 4300 11850 6800 *11850 *11850 *7350 *7350
(–5') (8900) (5400) (11200) (6800) (15900) (9500) (26100) (15000) (26100) (26100) (16200) (16200)
–3.0 m 4750 2850 5100 3050 7250 4300 11800 6750 *15650 13550 *10600 *10600
(–10') (10500) (6300) (11200) (6700) (15900) (9500) (26000) (14900) (34500) (29900) (23300) (23300)
–4.5 m 6250 3800 7350 4400 12000 6900 *19350 13900 *14400 *14400
(–15') (13800) (8400) (16200) (9700) (26400) (15200) (42600) (30700) (31800) (31800)
Arm length 2500 mm (8'2")
6.0 m *4750 3850 *5650 5600
(20') (10500) (8500) (12500) (12300)
4.5 m *4850 3200 5700 3600 *6500 5400 *7500 *7500
(15') (10700) (7100) (12500) (8000) (14300) (11900) (16500) (16500)
3.0 m 4600 2850 5550 3500 *7750 5050 *10150 8000
(10') (10200) (6300) (12200) (7700) (17100) (11200) (22300) (17600)
1.5 m 4450 2750 5350 3350 7700 4750 12450 7300
(5') (9800) (6100) (11800) (7400) (17000) (10500) (27500) (16200)
0m 4550 2800 5250 3200 7450 4550 12050 7000
(0') (10100) (6200) (11600) (7100) (16500) (10000) (26600) (15400)
–1.5 m 5050 3100 5200 3200 7350 4450 11950 6900 *13000 *13000 *8550 *8550
(–5') (11100) (6800) (11500) (7000) (16200) (9800) (26300) (15200) (28700) (28700) (18800) (18800)
–3.0 m 6100 3750 7400 4500 12050 7000 *19850 14000 *13900 *13900
(–10') (13500) (8300) (16400) (9900) (26600) (15400) (43800) (30900) (30700) (30700)
–4.5 m 9150 5550 *11700 7250 *16750 14500
(–15') (20100) (12200) (25800) (16000) (36900) (32000)
Arm length 2000 mm (6'7")
6.0 m *4850 4250 *6300 5450
(20') (10700) (9300) (13900) (12100)
4.5 m *4950 3450 5600 3550 *7100 5300 *8400 *8400 *12000 *12000
(15') (10900) (7600) (12400) (7800) (15600) (11600) (18600) (18600) (26500) (26500)
3.0 m 4950 3100 5450 3450 7950 5000 *11050 7750
(10') (10900) (6800) (12100) (7600) (17500) (11000) (24300) (17100)
1.5 m 4800 2950 5350 3300 7650 4700 12250 7150
(5') (10500) (6500) (11800) (7300) (16800) (10400) (27000) (15800)
0m 4950 3050 5250 3200 7450 4500 11950 6900
(0') (10900) (6700) (11600) (7100) (16400) (10000) (26400) (15200)
–1.5 m 5500 3400 7400 4450 11950 6900 *13550 *13550
(–5') (12200) (7500) (16300) (9900) (26300) (15200) (29900) (29900)
–3.0 m 6950 4250 7500 4550 12150 7050 *18650 14150
(–10') (15300) (9400) (16500) (10100) (26800) (15600) (41100) (31200)
–4.5 m *9750 6850 *10450 7450
(–15') (21500) (15100) (23100) (16400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-40
AH_25.book Page 41 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC270LC-7
Conditions: Boom: 5850 mm (19'2"), Bucket (SAE): 1.25 m3 (1.63 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3045 mm (10'0")
7.6 m *3250 *3250
(25') (7200) (7200)
6.1 m *3100 *3100 *4250 *4250 *6250 *6250
(20') (6900) (6900) (9400) (9400) (13700) (13700)
4.6 m *3150 *3150 *6200 4500 *7100 6750
(15') (7000) (7000) (13700) (10000) (15700) (14800)
3.0 m *3350 3300 *7200 4350 *8400 6400 *10750 10250 *16950 *16950
(10') (7400) (7200) (15900) (9600) (18500) (14100) (23700) (22600) (37300) (37300)
1.5 m *3700 3150 7100 4200 *9700 6050 *13300 9500 *8600 *8600
(5') (8200) (7000) (15600) (9300) (21400) (13300) (29300) (20900) (19000) (19000)
0m *4300 3250 6950 4050 9950 5800 *14800 9000 *9800 *9800
(0') (9500) (7100) (15300) (9000) (22000) (12700) (32600) (19900) (21600) (21600)
–1.5 m *5300 3550 6850 4000 9800 5650 *15100 8800 *13950 *13950 *8650 *8650
(–5') (11700) (7800) (15100) (8800) (21600) (12400) (33300) (19400) (30800) (30800) (19100) (19100)
–3.0 m 7200 4200 9800 5650 *14300 8850 *20100 18100 *13400 *13400
(–10') (15900) (9300) (21600) (12400) (31500) (19500) (44300) (39900) (29600) (29600)
–4.6 m *8350 5850 *11950 9100 *16950 *16950
(–15') (18400) (12900) (26400) (20000) (37400) (37400)
Arm length 3505 mm (11'6")
7.6 m *2495 *2485
(25') (5500) (5500)
6.1 m *2420 *2420 *4020 *4020
(20') (5300) (5300) (8800) (8800)
4.6 m *2480 *2480 *5465 4575 *6515 *6515
(15') (5400) (5400) (12000) (10000) (14300) (14300)
3.0 m *2660 *2660 *6750 4405 *7835 6475 *9825 *9825 *14430 *14430
(10') (5800) (5800) (14900) (9700) (17200) (14200) (21600) (21600) (31800) (31800)
1.5 m *2975 *2975 7110 4210 *9235 6090 *12535 9610 *13350 *13350
(5') (6500) (6500) (15600) (9200) (20300) (13400) (27600) (21100) (29400) (29400)
0m 3025 3485 6925 4045 9965 5780 *14350 9035 *11435 *11435 *5080 *5080
(0') (6600) (7600) (15200) (8900) (21900) (12700) (31600) (19900) (25200) (25200) (11200) (11200)
–1.5 m 3270 4345 6810 3945 9760 5600 *15015 8765 *14145 *14145 *8640 *8640
(–5') (7200) (9500) (15000) (8700) (21500) (12300) (33100) (19300) (31100) (31100) (19000) (19000)
–3.0 m 3840 6005 6810 3940 9710 5555 *14565 8735 *18730 17855 *12460 *12460
(–10') (8400) (13200) (15000) (8680) (21400) (12200) (32100) (19200) (41200) (39300) (27400) (27400)
–4.6 m 5145 8355 *9215 5675 *12790 8910 *18425 18290
(–15') (11300) (18400) (20300) (12500) (28200) (19600) (40600) (40300)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-41
AH_25.book Page 42 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC290LC-7
Conditions: One-piece Boom: 5850 mm (19'2"), Bucket (SAE): 1.16 m3 (1.52 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3000 mm (9'10")
6.0 m *3100 *3100 *4750 *4750
(20') (6800) (6800) (10450) (10450)
4.5 m *3150 *3150 *6500 4850 *7200 7200
(15') (6900) (6900) (14300) (10650) (15800) (15800)
3.0 m *3350 *3350 6900 4700 *8550 6850 *11000 10900 *17550 *17550
(10') (7350) (7350) (15150) (10300) (18800) (15050) (24200) (23950) (38600) (38600)
1.5 m *3700 3350 6700 4550 9600 6500 *13550 *10150 *8050 *8050
(5') (8100) (7350) (14700) (10000) (21100) (14300) (29800) (22300) (17700) (17700)
0m *4300 3400 6550 4400 9300 6200 15050 9850 *9500 *9500
(0') (9450) (7450) (14400) (9650) (20450) (13600) (33100) (21650) (20900) (20900)
–1.5 m *5250 3700 6450 4300 9050 5950 14850 9450 *13600 *13600 *8550 *8550
(–5') (11550) (8100) (14200) (9450) (19900) (13100) (32650) (20800) (29900) (29900) (18800) (18800)
–3.0 m 6550 4400 9150 6050 *14550 9500 *19500 *19500 *13200 *13200
(–10') (14400) (9650) (20100) (13300) (32000) (20900) (42900) (42900) (29000) (29000)
–4.5 m *8350 6000 *8750 *12300 9700 *17400 *17400
(–15') (18350) (13200) (19250) (27050) (21300) (38250) (38250)
Arm length 3500 mm (11'6")
6.0 m *2400 *2400 *4300 *4300
(20') (5250) (5250) (9450) (9450)
4.5 m *2450 *2450 *5650 4900 *6600 *6600
(15') (5400) (5400) (12400) (10750) (14500) (14500)
3.0 m *2650 *2650 *6850 4700 *7950 6900 *10050 *10050 *14800 *14800
(10') (5800) (5800) (15050) (10300) (17500) (15150) (22100) (22100) (32550) (32550)
1.5 m *2950 *2950 6700 4500 *9350 6500 *12800 10250 *12500 *12500
(5') (6500) (6500) (14700) (9900) (20550) (14300) (28150) (22550) (27500) (27500)
0m *3450 3150 6500 4350 9300 6200 *14600 9650 *11050 *11050 *5000 *5000
(0') (7600) (6900) (14300) (9550) (20450) (13600) (32100) (21200) (24300) (24300) (11000) (11000)
–1.5 m *4300 3400 6400 4250 9000 5900 14750 9400 *13750 *13750 *8500 *8500
(–5') (9450) (7450) (14050) (9350) (19800) (12950) (32450) (20650) (30250) (30250) (18700) (18700)
–3.0 m *5900 4000 6350 4250 8950 5900 14700 9350 *18200 *18200 *12250 *12250
(–10') (12950) (8800) (13950) (9350) (19700) (12950) (32300) (20550) (40000) (40000) (26950) (26950)
–4.5 m 7950 5300 9150 6050 *13100 9550 *18850 *18850
(–15') (17500) (11650) (20100) (13300) (28800) (21000) (41450) (41450)
Arm length 2500 mm (8'2")
6.0 m *5000 *5000 *7050 *7050
(20') (11000) (11000) (15500) (15500)
4.5 m *5150 4250 7000 4800 *7900 7050 *9450 *9450
(15') (11300) (9350) (15400) (10550) (17350) (15500) (20800) (20800)
3.0 m *5500 3900 6850 6450 *9150 6750 *12100 10650
(10') (12100) (8550) (15050) (14200) (20100) (14850) (26600) (23400)
1.5 m 5550 3750 6650 4500 9550 6400 *14300 9950
(5') (12200) (8250) (14600) (9900) (21000) (14050) (31450) (21900)
0m 5750 3650 6550 4400 9300 6200 14950 9550 *8900 *8900
(0') (12650) (8000) (14400) (9650) (20450) (13600) (32900) (21000) (19550) (19550)
–1.5 m 6300 4250 6500 4350 9200 6100 14850 9500 *15200 *15200
(–5') (13850) (9350) (14300) (9550) (20200) (13400) (32650) (20900) (33400) (33400)
–3.0 m *7700 5150 9250 6150 *13950 9600 *19550 *19550
(–10') (16900) (11300) (20350) (13500) (30700) (21100) (43000) (43000)
–4.5 m *8950 7650 *10950 9900
(–15') (19700) (16800) (24100) (21750)
Arm length 2000 mm (6'7")
6.0 m *5100 *5100 *7850 7150
(20') (11200) (11200) (17250) (15700)
4.5 m *5200 4600 *5950 4700 *8500 6950 *10400 *10400 *14950 *14950
(15') (11400) (10100) (13100) (10300) (18700) (15300) (22850) (22850) (32900) (32900)
3.0 m *5550 4150 6750 4800 *9650 6650 *12950 10400
(10') (12200) (9130) (14850) (10550) (21200) (14600) (28500) (22850)
1.5 m 5950 4050 6600 4450 9450 6350 *14850 9750
(5') (13100) (8900) (14500) (9800) (20800) (13950) (32650) (21450)
0m 6200 4150 6550 4400 9150 6050 14850 9500
(0') (13600) (9100) (14400) (9650) (20100) (13300) (32650) (20900)
–1.5 m 6950 4650 9200 6100 14850 9500 *15900 *15900
(–5') (15300) (10200) (20200) (13400) (32650) (20900) (34950) (34950)
–3.0 m 8700 5850 9300 6200 *13150 9650 *17800 *17800
(–10') (19100) (12800) (20450) (13600) (28900) (21200) (39150) (39150)
–4.5 m
(–15')
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-42
AH_25.book Page 43 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC290NLC-7
Conditions: One-piece Boom: 5850 mm (19'2"), Bucket (SAE): 1.16 m3 (1.52 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3000 mm (9'10")
6.0 m *3100 *3100 *4750 4450
(20') (6800) (6800) (10450) (9800)
4.5 m *3150 *3150 *6500 4350 *7200 6500
(15') (6900) (6900) (14300) (9550) (15800) (14300)
3.0 m *3350 *3050 6750 4200 *8550 6150 *11000 9750 *17550 *17550
(10') (7350) (6700) (14850) (9200) (18800) (13500) (24200) (21450) (38600) (38600)
1.5 m *3700 2950 6550 4050 9450 5800 *13550 9000 *8050 *8050
(5') (8100) (6500) (14400) (8900) (20800) (12750) (29800) (19800) (17700) (17700)
0m *4300 3000 6400 3900 9150 5550 14800 8550 *9500 *9500
(0') (9450) (6600) (14050) (8550) (20100) (12200) (32550) (18800) (20900) (20900)
–1.5 m *5250 3300 6350 3800 8900 5300 14600 8350 *13600 *13600 *8550 *8550
(–5') (11550) (7250) (13950) (8350) (19550) (11650) (32100) (18350) (29900) (29900) (18800) (18800)
–3.0 m 6450 3900 9000 5400 *14550 8400 *19500 16850 *13200 *13200
(–10') (14200) (8550) (19800) (11850) (32000) (18450) (42900) (37050) (29000) (29000)
–4.5 m *8350 5350 *8750 5550 *12300 8600 *17400 17300
(–15') (18350) (11750) (19250) (12200) (27050) (18900) (38250) (38050)
Arm length 3500 mm (11'6")
6.0 m *2400 *2400 *4300 *4300
(20') (5250) (5250) (9450) (9450)
4.5 m *2450 *2450 *5650 4400 *6600 6550
(15') (5400) (5400) (12400) (9650) (14500) (14400)
3.0 m *2650 *2650 6800 4250 *7950 6200 *10050 9950 *14800 *14800
(10') (5800) (5800) (14950) (9350) (17500) (13600) (22100) (21900) (32550) (32550)
1.5 m *2950 2750 6550 4050 *9350 5800 *12800 9100 *12500 *12500
(5') (6500) (6050) (14400) (8900) (20550) (12750) (28150) (20000) (27500) (27500)
0m *3450 2800 6400 3850 9150 5500 *14600 8550 *11050 *11050 *5000 *5000
(0') (7600) (6150) (14050) (8450) (20100) (12100) (32100) (18800) (24300) (24300) (11000) (11000)
–1.5 m *4300 3000 6250 3750 8850 5250 14500 8300 *13750 *13750 *8500 *8500
(–5') (9450) (6600) (13750) (8250) (19450) (9350) (31900) (18250) (30250) (30250) (18700) (18700)
–3.0 m *5900 3550 6250 3750 8800 5200 14500 8250 *18200 16550 *12250 *12250
(–10') (12950) (7800) (13750) (8250) (19350) (11400) (31900) (18150) (40000) (36400) (26950) (26950)
–4.5 m 7800 4700 9000 5400 *13100 8450 *18850 17000
(–15') (17150) (10300) (19800) (11850) (28800) (18600) (41450) (37400)
Arm length 2500 mm (8'2")
6.0 m *5000 4550 *7050 6600
(20') (11000) (10000) (15500) (14500)
4.5 m *5150 3850 6850 4300 *7900 6400 *9450 *9450
(15') (11300) (8450) (15050) (9450) (17350) (14050) (20800) (20800)
3.0 m *5500 3450 6700 4150 *9150 6050 *12100 9500
(10') (12100) (7600) (14700) (9100) (20100) (13300) (26600) (20900)
1.5 m 5450 3350 6550 4000 9400 5750 *14300 8850
(5') (12000) (7350) (14400) (8800) (20650) (12650) (31450) (19450)
0m 5650 3400 6400 3900 9150 5500 14700 8500 *8900 *8900
(0') (12400) (7450) (14050) (8550) (20100) (12100) (32300) (18700) (19550) (19550)
–1.5 m 6200 3750 6400 3850 9000 5400 14600 8400 *15200 *15200
(–5') (13600) (8250) (14050) (8450) (19800) (11850) (32100) (18450) (33400) (33400)
–3.0 m 7600 4500 9100 5450 *13950 8500 *19550 17050
(–10') (16700) (9900) (20000) (12000) (30700) (18700) (43000) (37500)
–4.5 m *8950 6850 *10950 8800
(–15') (19700) (15050) (24100) (19350)
Arm length 2000 mm (6'7")
6.0 m *5100 5000 *7850 6450
(20') (11200) (11000) (17250) (14200)
4.5 m *5200 4150 *5950 4200 *8500 6250 *10400 10050 *14950 *14950
(15') (11400) (9100) (13100) (9200) (18700) (13750) (22850) (22000) (32900) (32900)
3.0 m *5550 3700 6650 4100 *9650 5950 *12950 9250
(10') (12200) (8100) (14600) (9000) (21200) (13100) (28500) (20350)
1.5 m 5850 3600 6500 4000 9300 5650 *14850 8650
(5') (12850) (7900) (14300) (8800) (20450) (12400) (32650) (19000)
0m 6100 3700 6400 3900 9000 5400 14600 8400
(0') (13400) (8100) (14050) (8550) (19800) (11850) (32100) (18450)
–1.5 m 6800 4150 9050 5450 14600 8400 *15900 *15900
(–5') (14950) (9100) (19900) (12000) (32100) (18450) (34950) (34950)
–3.0 m 8600 5200 9150 5550 *13150 8550 *17800 17200
(–10') (18900) (11400) (20100) (12200) (28900) (18800) (39150) (37800)
–4.5 m
(–15')
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-43
AH_25.book Page 44 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC300-7
Conditions: Boom: 6470 mm (21'3"), Bucket (SAE): 1.40 m3 (1.83 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3185 mm (10'5")
7.6 m *4600 *4600 *5950 5200
(25') (10100) (10100) (13200) (11500)
6.1 m *4500 3750 *6550 5200
(20') (9900) (8300) (14400) (11400)
4.6 m *4600 3250 5200 3500 *7050 5000 *8150 7400
(15') (10100) (7200) (11500) (7700) (15500) (11000) (18000) (16300)
3.0 m 4500 2950 5100 3350 *6950 4700 *9500 6850 *12650 10550
(10') (9900) (6500) (11200) (7400) (15300) (10400) (20900) (15100) (27900) (23300)
1.5 m 4350 2800 4950 3250 6700 4450 9550 6350 *14800 9750
(5') (9600) (6200) (10900) (7100) (14800) (9800) (21100) (14000) (32600) (21500)
0m 4450 2850 4800 3100 6450 4250 9150 6000 14600 9200 *7250 *7250
(0') (9800) (6300) (10500) (6900) (14200) (9400) (20200) (13200) (32200) (20300) (16000) (16000)
–1.5 m 4750 3100 4800 3100 6350 4150 9000 5800 14400 9050 *11750 *11750
(–5') (10500) (6800) (10500) (6800) (14000) (9100) (19800) (12800) (31700) (19900) (25900) (25900)
–3.0 m 5500 3550 6350 4150 8950 5800 *13950 9100 *17200 *17200
(–10') (12100) (7900) (14000) (9100) (19700) (12800) (30800) (20100) (37900) (37900)
–4.6 m *6700 4750 *8500 6000 *11350 9350 *15250 *15200
(–15') (14700) (10400) (18700) (13200) (25000) (20700) (33600) (33700)
–6.1 m *5600 *5600 *6750 *6750
(–20') (12300) (12300) (14900) (14900)
Arm length 4020 mm (13'2")
7.6 m *3550 *3550
(25') (7900) (7900)
6.1 m *3500 3200 *5350 3750
(20') (7700) (7000) (11800) (8300)
4.6 m *3550 2800 5400 3650 *6400 5200
(15') (7800) (6200) (11900) (8100) (14100) (11500)
3.0 m *3700 2550 5200 3500 7150 4900 *8600 7100 *11200 *11200 18050 18050
(10') (8200) (5600) (11500) (7700) (15800) (10800) (19000) (15700) (24700) (24700) (39800) (39800)
1.5 m 3800 2450 5000 3300 6800 4550 9750 6500 *13650 10100 *8050 *8050
(5') (8400) (5400) (11000) (7300) (15000) (10000) (21500) (14400) (30100) (22300) (17800) (17800)
0m 3850 2450 4850 3150 6500 4300 9250 6050 14700 9300 *8100 *8100
(0') (8500) (5400) (10700) (6900) (14300) (9400) (20400) (13300) (32400) (20500) (17800) (17800)
–1.5 m 4100 2600 4750 3050 6300 4100 8900 5750 14250 8900 *10800 *10800
(–5') (9000) (5700) (10500) (6700) (13900) (9000) (19700) (12700) (31400) (19600) (23800) (23800)
–3.0 m 4550 2950 4750 3050 6250 4000 8800 5650 14150 8800 *14650 *14650
(–10') (10000) (6500) (10400) (6700) (13700) (8900) (19400) (12500) (31200) (19400) (32300) (32300)
–4.6 m 5600 3650 6300 4100 8900 5750 *12800 9000 *18300 *18300
(–15') (12300) (8000) (13900) (9000) (19600) (12600) (28200) (19800) (40300) (40300)
–6.1 m *5800 5250 *6950 6000 *9550 9350 *13100 *13100
(–20') (12800) (11600) (15300) (13200) (21100) (20700) (28800) (28800)
Arm length 2200 mm (7'3")
7.6 m *7650 6400
(25') (16900) (14100)
6.1 m 7000 4800 7200 4950 *8200 7450
(20') (15400) (10600) (15900) (10900) (18100) (16400)
4.6 m 5950 4000 7050 4800 *9100 7050 *11750 11200
(15') (13100) (8800) (15500) (10600) (20100) (15500) (26000) (24700)
3.0 m 5350 3550 6750 4550 9700 6500 *14200 9900
(10') (11800) (7800) (14900) (10000) (21400) (14300) (31300) (21800)
1.5 m 5200 3400 6550 4300 9050 5900 14450 9100
(5') (11500) (7500) (14400) (9500) (20000) (13000) (31900) (20100)
0m 5350 3450 6350 4150 8950 5800 14200 8850
(0') (11800) (7600) (14000) (9200) (19700) (12800) (31300) (19500)
–1.5 m 5850 3800 6350 4100 8900 5750 *14100 8900 *14200 *14200
(–5') (12900) (8400) (14000) (9100) (19600) (12600) (31100) (19600) (31300) (31300)
–3.0 m 7100 4650 8850 5700 *12200 9100 *15100 *15100
(–10') (15700) (10300) (19500) (12600) (26900) (20100) (33300) (33300)
–4.6 m *6900 *6900 *8550 *8550
(–15') (15200) (15200) (18800) (18800)
Arm length 2550 mm (8'4")
7.6 m *6500 5500
(25') (14400) (12100)
6.1 m 6250 4250 *7100 5050
(20') (13800) (9400) (15700) (11100)
4.6 m 5400 3600 7150 4850 *8800 7150
(15') (11900) (7900) (15700) (10700) (19400) (15800)
3.0 m 4950 3250 6850 4600 9850 6600 *13750 10200
(10') (10900) (7200) (15100) (10100) (21700) (14500) (30300) (22500)
1.5 m 4800 3100 6600 4350 9350 6150 14750 9350
(5') (10600) (6800) (14500) (9600) (20600) (13600) (32500) (20600)
0m 4900 3200 6400 4200 9050 5850 14350 9000
(0') (10800) (7000) (14100) (9200) (19900) (12900) (31600) (19800)
–1.5 m 5350 3450 6350 4100 8900 5750 14300 8950 *12350 *12350
(–5') (11800) (7600) (14000) (9100) (19700) (12700) (31600) (19700) (27200) (27200)
–3.0 m 6300 4100 6400 4200 8800 5650 *12900 9100 *16850 *16850
(–10') (13900) (9100) (14100) (9200) (19400) (12400) (28400) (20100) (37200) (37200)
–4.6 m *6600 5800 *7100 6100 *9650 9500 *12100 *12100
(–15') (14600) (12800) (15600) (13500) (21300) (20900) (26700) (26700)
2C-44
AH_25.book Page 45 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-45
AH_25.book Page 46 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC300HD-7
Conditions: Boom: 6500 mm (21'3"), Bucket (SAE): 1.40 m3 (1.83 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3185 mm (10'5")
7.6 m *5000 *5000 *6500 *6500
(25') (11000) (11000) (14300) (14300)
6.1 m *4900 *4900 *7200 *7200
(20') (10800) (10800) (15800) (15800)
4.6 m *5050 *5050 *6800 5450 *7750 7500 *8900 *8900
(15') (11100) (11100) (15000) (12100) (17000) (16500) (19600) (19600)
3.0 m *5350 4750 *7350 5350 *8500 7200 *10350 10200 *13800 *13800
(10') (11800) (10500) (16200) (11800) (18700) (15900) (22900) (22500) (30400) (30400)
0m *6650 4700 7350 6100 *9600 6750 *12300 9350 *17000 14350 *7900 *7900
(0') (14600) (10400) (16200) (11200) (21100) (14800) (27100) (20600) (37500) (31700) (17400) (17400)
–3.0 m *7550 6750 *8800 6600 *11600 9150 *15300 14250 *18500 *18500
(–10') (16600) (12700) (19400) (14600) (25400) (20200) (33700) (31400) (40800) (40800)
–4.6 m *7400 *7400 *9400 9350 *12450 *12450 *16800 *16800
(–15') (16300) (16300) (20700) (20600) (27500) (27500) (37000) (37000)
Arm length 4020 mm (13'2")
7.6 m *3750 *3750
(25') (8300) (8300)
6.1 m *3700 *3700 *5600 5550
(20') (8100) (8100) (12400) (12300)
4.6 m *3750 *3750 *6300 5450 *6900 *6900
(15') (8300) (8300) (13900) (12000) (15200) (15200)
3.0 m *3950 *3950 *6750 5300 *7700 7250 *9250 *9250 *12050 *12050
(10') (8700) (8700) (14800) (11700) (17000) (15900) (20400) (20400) (26600) (26600)
1.5 m *4250 3950 *7150 5100 *8500 6900 *10700 9800 *14850 *14850
(5') (9400) (8700) (15800) (11300) (18700) (15200) (23500) (21600) (32700) (32700)
0m *4750 4000 7150 4950 *9100 6600 *11700 9300 *16450 14450 *9100 *9100
(0') (10500) (8800) (15800) (10900) (20100) (14600) (25800) (20500) (36200) (31800) (20100) (20100)
–1.5 m *5500 4200 7050 4850 *9350 6400 *12100 9000 *16750 14050 *8850 *8850
(–5') (12200) (9300) (15600) (10700) (20600) (14100) (26700) (19800) (36900) (30900) (19600) (19600)
–3.0 m *6700 4750 *6900 4850 *9050 6350 *11750 8900 *15950 13950 *16000 *16000
(–10') (14800) (10400) (15200) (10700) (19900) (14000) (25900) (19600) (35200) (30800) (35300) (35300)
–4.6 m *6700 5750 *7800 6400 *10300 8750 *14050 *14050 *19750 *19750
(–15') (14800) (12600) (17200) (14200) (22700) (19300) (31000) (31000) (43600) (43600)
–6.1 m *6350 *6350 *7600 *7600 *10500 10500 *14200 *14200
(–20') (14800) (14800) (16700) (16700) (23100) (23100) (31300) (31300)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-46
AH_25.book Page 47 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC300SE-7
Conditions: Boom: 6470 mm (21'3"), Bucket (SAE): 2.1 m3 (2.74 cu.yd), Shoes: 800 mm (31.5") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2200 mm (7'3")
7.6 m *7000 6600 *7150 *7150
(25') (15450) (14500) (15750) (15750)
6.1 m *6550 5200 *6650 5200 *7350 *7350
(20') (14450) (11500) (14650) (11450) (16200) (16200)
4.6 m 5200 4300 *6950 5050 *6900 *6900 *10750 *10750
(15') (11500) (9500) (15350) (11100) (15250) (15250) (23650) (23650)
3.0 m 6200 3850 *7450 4800 *9200 6900 *12950 10450
(10') (13700) (8450) (16400) (10550) (20250) (15150) (28500) (23100)
1.5 m 5950 3600 7400 4550 *9900 6450 *13900 9700
(5') (13150) (8000) (16350) (10050) (21750) (14200) (30600) (21350)
0m 6200 3750 7250 4400 *10000 6200 *13600 9450
(0') (13650) (8250) (16000) (9700) (22100) (13600) (29950) (20800)
–1.5 m 6850 4150 7200 4350 *8100 6100 *12500 9500
(–5') (15100) (9150) (15900) (9650) (17900) (13500) (27600) (20900)
–3.0 m *6850 5100 *8150 6250 *10600 9700
(–10') (15150) (11250) (17900) (13750) (23400) (21450)
–4.6 m *6000 *6000 *7000 *7000
(–15') (13250) (13250) (15400) (15400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-47
AH_25.book Page 48 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC300LC-7
Conditions: Boom: 6470 mm (21'3"), Bucket (SAE): 1.40 m3 (1.83 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3185 mm (10'5")
7.6 m *4600 *4600 *5950 5500
(25') (10100) (10100) (13200) (12100)
6.1 m *4500 3950 *6550 5450
(20') (9900) (8800) (14400) (12000)
4.6 m *4600 3450 6150 3700 *7050 5250 *8150 7750
(15') (10200) (7600) (13600) (8200) (15500) (11600) (18000) (17100)
3.0 m *4900 3100 6050 3550 *7750 5000 *9500 7200 *12650 11050
(10') (10800) (6900) (13300) (7900) (17100) (11000) (20900) (15800) (27900) (24400)
1.5 m 5200 3000 5900 3450 7950 4700 *10600 6700 *14800 10250
(5') (11500) (6600) (13000) (7600) (17500) (10400) (23400) (14800) (32700) (22600)
0m 5300 3050 5750 3350 7700 4500 10950 6350 *15600 9700 *7250 *7250
(0') (11700) (6700) (12700) (7400) (17000) (9900) (24200) (14000) (34300) (21400) (16000) (16000)
–1.5 m 5700 3300 5700 3300 7600 4400 10750 6150 *15250 9550 *11750 *11750
(–5') (12600) (7300) (12600) (7300) (16700) (9700) (23700) (13600) (33600) (21000) (25900) (25900)
–3.0 m 6550 3800 7600 4400 *10500 6150 *13950 9600 *17200 *17200
(–10') (14500) (8400) (16700) (9700) (23100) (13600) (30800) (21200) (37900) (37900)
–4.6 m *6700 5000 *8500 6300 *11350 9850 *15250 *15250
(–15') (14700) (11100) (18800) (13900) (25000) (21800) (33700) (33700)
–6.1 m *5600 *5600 *6750 *6750
(–20') (12300) (12300) (14900) (14900)
Arm length 4020 mm (13'2")
7.6 m *3550 *3550
(25') (7900) (7900)
6.1 m *3500 3400 *5350 4000
(20') (7700) (7500) (11800) (8800)
4.6 m *3550 2950 *5850 3850 *6400 5500
(15') (7800) (6500) (13000) (8500) (14100) (12100)
3.0 m *3700 2700 6150 3700 *7200 5150 *8600 7450 *11200 *11200 18050 18050
(10') (8200) (6000) (13600) (8200) (15800) (11300) (19000) (16400) (24700) (24700) (39800) (39800)
1.5 m *4000 2600 5950 3500 *7900 4800 *9900 6850 *13650 10600 *8050 *8050
(5') (8800) (5800) (13200) (7700) (17400) (10500) (21800) (15100) (30100) (23400) (17800) (17800)
0m *4450 2650 5800 3350 7750 4550 *10800 6400 *15050 9800 *8100 *8100
(0') (9800) (5800) (12800) (7400) (17100) (10000) (23800) (14100) (32200) (21600) (17800) (17800)
–1.5 m 4900 2800 5700 3250 7550 4350 10700 6100 *15350 9400 *10800 *10800
(–5') (10800) (6100) (12600) (7200) (16600) (9600) (23600) (13400) (33800) (20700) (23800) (23800)
–3.0 m 5500 3150 5650 3250 7450 4300 10600 6000 *14650 9300 *14650 *14650
(–10') (12100) (6900) (12500) (7100) (16500) (9400) (23300) (13200) (32300) (20500) (32300) (32300)
–4.6 m *6200 3900 *7200 4350 *9600 6050 *12800 9500 *18300 *18300
(–15') (13600) (8600) (15900) (9600) (21200) (13400) (28200) (20900) (40300) (40300)
–6.1 m *5800 5550 *6950 6350 *9550 *9550 *13100 *13100
(–20') (12800) (12200) (15300) (14000) (21100) (21100) (28800) (28800)
Arm length 2200 mm (7'3")
7.6 m *7650 6700
(25') (16900) (14700)
6.1 m *7350 5050 *7400 5200 *8200 7800
(20') (16200) (11100) (16300) (11400) (18100) (17200)
4.6 m 7000 4200 *7750 5050 *9100 7400 *11750 11700
(15') (15500) (9300) (17000) (11100) (20100) (16300) (26000) (25800)
3.0 m 6400 3750 8050 4800 *10250 6850 *14200 10400
(10') (14100) (8300) (17700) (10600) (22600) (15100) (31300) (22900)
1.5 m 6200 3600 7750 4550 10850 6250 *15350 9600
(5') (13700) (8000) (17100) (10100) (24000) (13800) (33900) (21200)
0m 6400 3700 7600 4400 10750 6150 *15150 9350
(0') (14100) (8100) (16800) (9700) (23700) (13500) (33400) (20600)
–1.5 m 7000 4050 7550 4350 10650 6050 *14100 9400 *14200 *14200
(–5') (15500) (9000) (16700) (9600) (23500) (13400) (31100) (20700) (31300) (31300)
–3.0 m *7650 4900 *9300 6050 *12200 9600 *15100 *15100
(–10') (16900) (10800) (20500) (13400) (26900) (21200) (33300) (33300)
–4.6 m *6900 *6900 *8550 *8550
(–15') (15200) (15200) (18800) (18800)
Arm length 2550 mm (8'4")
7.6 m *6500 5750
(25') (14400) (12700)
6.1 m *6400 4500 *7100 5300
(20') (14100) (9900) (15700) (11700)
4.6 m 6400 3600 *7500 5100 *8800 7500
(15') (11900) (7900) (16600) (11300) (19400) (16600)
3.0 m 5900 3450 8100 4850 *10000 6950 *13750 10700
(10') (13000) (7600) (17900) (10700) (22100) (15300) (30300) (23600)
1.5 m 5750 3300 7850 4600 *10900 6500 *15250 9850
(5') (12600) (7300) (17300) (10200) (24100) (14300) (33700) (21700)
0m 5850 3300 7650 4450 10800 6200 *15450 9500
(0') (12900) (7300) (16800) (9800) (23900) (13700) (34000) (20900)
–1.5 m 6400 3700 7550 4350 10700 6100 *14600 9450 *12350 *12350
(–5') (14100) (8100) (16700) (9600) (23600) (13500) (32200) (20800) (27200) (27200)
–3.0 m *7150 4350 *7300 4450 *9700 6000 *12900 9600 *16850 *16850
(–10') (15800) (9600) (16100) (9800) (21400) (13200) (28400) (21200) (37200) (37200)
–4.6 m *6600 6100 *7100 6450 *9650 *9650 *12100 *12100
(–15') (14600) (13500) (15600) (14200) (21300) (21300) (26700) (26700)
2C-48
AH_25.book Page 49 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-49
AH_25.book Page 50 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 4020 mm (13'2")
7.6 m *3900 *3900
(25') (8600) (8600)
6.1 m *3850 3800
(20') (8500) (8400)
4.6 m *3900 3350 *7050 6000
(15') (8600) (7400) (15500) (13300)
3.0 m *4050 3100 7850 5700 *9350 8250 *12200 *12200
(10') (9000) (6900) (17300) (12600) (20700) (18200) (26900) (26900)
1.5 m *4400 3000 *8650 5350 *10800 7650 *14950 11850 *9300 *9300
(5') (9700) (6600) (19100) (11800) (23900) (16800) (33000) (26100) (20500) (20500)
0m *4850 3050 8450 5100 *11850 7150 *16600 11000 *9050 *9050
(0') (10700) (6700) (18700) (11200) (26100) (15800) (36500) (24200) (19900) (19900)
–1.5 m 5450 3200 8250 4900 11750 6850 *16900 10600 *11900 *11900 *7500 *7500
(–5') (12000) (7100) (18200) (10800) (25900) (15100) (37300) (23400) (26300) (26300) (16500) (16500)
–3.0 m 6100 3600 8200 4850 11650 6750 *16100 10550 *16200 *16200 *11300 *11300
(–10') (13400) (7900) (18100) (10700) (25600) (14900) (35500) (23200) (35700) (35700) (24900) (24900)
–4.6 m *6450 6200 *7700 7150 *10650 *10650 *14350 *14350
(–15') (14300) (13700) (17000) (15700) (23400) (23400) (31600) (31600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-50
AH_25.book Page 51 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC340LC-7
Conditions: Boom: 6470 mm (21'3"), Bucket (SAE): 1.38 m3 (1.80 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3200 mm (10'6")
6.0 m *4900 4250 *7150 6000
(20') (10750) (9350) (15700) (13200)
4.5 m *5000 3700 *7700 5750 *8950 8500
(15') (11000) (8100) (16900) (12650) (19700) (18700)
3.0 m *5300 3400 *8450 5450 *10350 7900 *13900 12200
(10') (11650) (7450) (18600) (12000) (22750) (17350) (30550) (26800)
1.5 m 5550 3250 8600 5200 *11600 7350 *16350 11350
(5') (12200) (7150) (18900) (11400) (25500) (16150) (35950) (24950)
0m 5650 3300 8350 4950 11950 6950 *17150 10750 *7850 *7850
(0') (12400) (7250) (18350) (10900) (26300) (15300) (37700) (23650) (17250) (17250)
–1.5 m 6100 3550 8200 4800 *11700 6800 *16750 10600 *12650 *12650 *8850 *8850
(–5') (13400) (7800) (18000) (10550) (25700) (14950) (36850) (23300) (27800) (27800) (19450) (19450)
–3.0 m 6950 4100 8200 4800 *11500 6750 *15300 10650 *18500 *18500 *13600 *13600
(–10') (15300) (9000) (18000) (10550) (25300) (14850) (33650) (23400) (40700) (40700) (29900) (29900)
–4.5 m *7250 5250 *9550 6950 *12650 10950 *16750 *16750
(–15') (15900) (11550) (21000) (15300) (27800) (24100) (36850) (36850)
Arm length 4000 mm (13'1")
6.0 m *3700 3550
(20') (8100) (7800)
4.5 m *3750 3150 *6950 5950
(15') (8250) (6900) (15300) (13100)
3.0 m *3950 2900 *7800 5600 *9400 8200 *12300 *12300 *19450 *19450
(10') (8700) (6350) (17150) (12300) (20650) (18000) (27050) (27050) (42800) (42800)
1.5 m *4250 2800 *8600 5250 *10850 7550 *15100 11800 *8550 *8550
(5') (9350) (6150) (18900) (11550) (23850) (16600) (33200) (25950) (18800) (18800)
0m *4750 2800 8400 4950 *11850 7050 *16650 10900 *8600 *8600
(0') (10450) (6150) (18450) (10900) (26050) (15500) (36600) (23950) (18900) (18900)
–1.5 m 5200 3000 8200 4800 11700 6750 *16950 10500 *11450 *11450 *7250 *7250
(–5') (11400) (6600) (18000) (10550) (25700) (14850) (37300) (23100) (25200) (25200) (15950) (15950)
–3.0 m 5800 3350 8100 4700 11550 6650 *16150 10450 *15600 *15600 *11000 *11000
(–10') (12750) (7350) (17800) (10300) (25400) (14600) (35500) (23000) (34300) (34300) (24200) (24200)
–4.5 m *6650 4100 *8050 4750 *10700 6700 *14300 10600 *20050 *20050 *15350 *15350
(–15') (14600) (9000) (17700) (10450) (23500) (14700) (31450) (23300) (44100) (44100) (33750) (33750)
Arm length 2550 mm (8'4")
6.0 m *6900 4850 *7800 5900
(20') (15150) (10650) (17150) (12950)
4.5 m 6850 4150 *8300 5700 *9800 8350 *12600 *12600
(15') (15050) (9100) (18250) (12500) (21550) (18350) (27700) (27700)
3.0 m 6350 3800 8900 5450 *11100 7750 *15350 12000
(10') (13950) (8350) (19550) (12000) (24400) (17050) (33750) (26400)
1.5 m 6200 3700 8600 5200 *12100 7300 *17050 11050
(5') (13600) (8100) (18900) (11400) (26600) (16050) (37500) (24300)
0m 6350 3750 8400 5000 11900 6950 *17150 10700
(0') (13950) (8250) (18450) (11000) (26150) (15300) (37700) (23500)
–1.5 m 6900 4100 8300 4900 11800 6850 *16200 10650 *13350 *13350
(–5') (15150) (9000) (18250) (10750) (25450) (15050) (35600) (23400) (29350) (29350)
–3.0 m *7850 4800 *8200 5000 *10750 6700 *14300 10850 *18400 *18400
(–10') (17250) (10550) (18000) (11000) (23650) (14700) (31450) (23850) (40450) (40450)
–4.5 m *7350 6500 *8250 7200 *11000 *11000 *13650 *13650
(–15') (16150) (14300) (18150) (15800) (24200) (24200) (30000) (30000)
Arm length 2200 mm (7'3")
6.0 m *8000 5400 *8150 5800 *9100 8650
(20') (17600) (11850) (17900) (12750) (20000) (19000)
4.5 m 7500 4600 *8550 5600 *10150 8200 *13250 13000
(15') (16500) (10100) (18800) (12300) (22300) (18000) (29150) (28600)
3.0 m 6900 4150 8800 5350 *11350 7650 *15900 11650
(10') (15150) (9100) (19350) (11750) (24950) (16800) (34950) (25600)
1.5 m 6700 4000 8550 5100 11900 6950 *17150 10800
(5') (14700) (8800) (18800) (11200) (26150) (15300) (37700) (23750)
0m 6900 4100 8350 4950 11850 6900 *16850 10550
(0') (15150) (9000) (18350) (10900) (26050) (15150) (37050) (23200)
–1.5 m 7550 4500 8300 4900 11750 6800 *15650 10600 *15300 *15300
(–5') (16600) (9900) (18250) (10750) (25850) (14950) (34400) (23300) (33650) (33650)
–3.0 m *8350 5400 *10350 6750 *13500 10850 *16500 *16500
(–10') (18350) (11850) (22750) (14850) (29700) (23850) (36300) (36300)
–4.5 m *7700 *7700 *9850 *9850 *11600 *11600
(–15') (16900) (16900) (21650) (21650) (25500) (25500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-51
AH_25.book Page 52 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC340NLC-7
Conditions: Boom: 6470 mm (21'3"), Bucket (SAE): 1.38 m3 (1.80 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3200 mm (10'6")
6.0 m *4900 3800 *7150 5400
(20') (10750) (8350) (15700) (11850)
4.5 m *5000 3250 *7700 5200 *8950 7700
(15') (11000) (7150) (16900) (11400) (19700) (16900)
3.0 m *5300 3600 *8450 4900 *10350 7100 *13900 10900
(10') (11650) (7900) (18600) (10750) (22750) (15200) (30550) (23950)
1.5 m 5450 2850 8450 4600 *11600 6600 *16350 10050
(5') (12000) (6250) (18600) (10100) (25500) (14500) (35950) (22100)
0m 5550 2900 8200 4400 11750 6200 *17150 9500 *7850 *7850
(0') (12200) (6350) (18000) (9650) (25850) (13600) (37700) (20900) (17250) (17250)
–1.5 m 5950 3150 8100 4250 *11500 6000 *15300 9400 *18500 *18500 *8850 *8850
(–5') (13100) (6900) (17800) (9350) (25300) (13200) (33650) (20650) (40700) (40700) (19450) (19450)
–3.0 m 6850 3600 8100 4250 *11500 6000 *15300 9400 *18500 *18500 *13600 *13600
(–10') (15050) (7900) (17800) (9350) (25300) (13200) (33650) (20650) (40700) (40700) (29900) (29900)
–4.5 m *7250 4700 *9550 6150 *12650 9650 *16750 *16750
(–15') (15900) (10300) (21000) (13500) (27800) (21200) (36850) (36850)
Arm length 4000 mm (13'1")
6.0 m *3700 3150
(20') (8100) (6900)
4.5 m *3750 2750 *6950 5400
(15') (8250) (6050) (15300) (11850)
3.0 m *3950 2550 *7800 5050 *9400 7400 *12300 11800 *19450 *19450
(10') (8700) (5600) (17150) (11100) (20650) (16250) (27050) (25950) (42800) (42800)
1.5 m *4250 2450 8600 4700 *10850 6750 *15100 10500 *8550 *8550
(5') (9350) (5400) (18900) (10340) (23850) (14850) (33200) (23100) (18800) (18800)
0m *4750 2450 8250 4400 11850 6250 *16650 9650 *8600 *8600
(0') (10450) (5400) (18150) (9650) (26050) (13750) (36600) (21200) (18900) (18900)
–1.5 m 5100 2600 8050 4200 11500 5950 *16950 9250 *11450 *11450 *7250 *7250
(–5') (11220) (5700) (17700) (9200) (25300) (13100) (37300) (20350) (25200) (25200) (15950) (15950)
–3.0 m 5700 2950 7950 4150 11400 5850 *16150 9200 *15600 *15600 *11000 *11000
(–10') (12500) (6500) (17500) (9100) (25050) (12850) (35500) (20200) (34300) (34300) (24200) (24200)
–4.5 m *6650 3600 8050 4200 *10700 5950 *14300 9350 *20050 18950 *15350 *15350
(–15') (14600) (7900) (17700) (9200) (23500) (13100) (31450) (20550) (44100) (41700) (33750) (33750)
Arm length 2550 mm (8'4")
6.0 m *6900 4350 *7800 5350
(20') (15150) (9550) (17150) (11750)
4.5 m 6700 3750 *8300 5150 *9800 7550 *12600 12000
(15') (14700) (8250) (18250) (11300) (21550) (16600) (27700) (26400)
3.0 m 6250 3400 8750 4900 *11100 7000 *15350 10700
(10') (13750) (7450) (19250) (10750) (24400) (15400) (33750) (23500)
1.5 m 6050 3250 8600 4600 12100 6500 *17150 9450
(5') (13300) (7150) (18900) (10100) (26600) (14300) (37700) (20800)
0m 6250 3300 8400 4450 11750 6200 *17150 9450
(0') (13750) (7250) (18450) (9800) (25850) (13600) (37700) (20800)
–1.5 m 6750 3600 8300 4350 11600 6100 *16200 9400 *13350 *13350
(–5') (14850) (7900) (18250) (9550) (25500) (13400) (35600) (20650) (29350) (29350)
–3.0 m *7850 4300 *8200 4450 *10750 5950 *14300 9600 *18400 *18400
(–10') (17250) (9450) (18000) (9800) (23650) (13100) (31450) (21100) (40450) (40450)
–4.5 m *7350 5800 *8250 6400 *11000 9950 *13650 *13650
(–15') (16150) (12750) (18150) (14050) (24200) (21900) (30000) (30000)
Arm length 2200 mm (7'3")
6.0 m *8000 4900 *8150 5250 *9100 7850
(20') (17600) (10750) (17900) (11550) (20000) (17250)
4.5 m 7350 4100 *8550 5050 *10150 7400 *13250 11700
(15') (16150) (9000) (18800) (11100) (22300) (16250) (29150) (25700)
3.0 m 6750 3700 8800 4800 *11350 6850 *15900 10350
(10') (14850) (8100) (19350) (10550) (24950) (15050) (34950) (22750)
1.5 m 6600 3550 8550 4550 11750 6200 *17150 9550
(5') (14500) (7800) (18800) (10000) (25850) (13600) (37700) (21000)
0m 6750 3600 8350 4400 11650 6100 *16850 9300
(0') (14850) (7900) (18350) (9650) (25600) (13400) (37050) (20450)
–1.5 m 7400 3950 8300 4350 11550 6050 *15850 9350 *15300 *15300
(–5') (16250) (8700) (18250) (9550) (25400) (13300) (34850) (20550) (33650) (33650)
–3.0 m *8350 4800 *10350 6000 *13500 9600 *16500 *16500
(–10') (18350) (10550) (22750) (13200) (29700) (21100) (36300) (36300)
–4.5 m *7700 6900 *9850 *9850 *11600 *11600
(–15') (16900) (15150) (21650) (21650) (25500) (25500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-52
AH_25.book Page 53 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-53
AH_25.book Page 54 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC380LC-7
Conditions: Boom: 6470 mm (21'3"), Bucket (SAE): 1.38 m3 1.81 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (20') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2200 mm (7'3")
6.0 m 8000* 6950 8150* 7450* 9150* 9150*
(20') (17600) (15300) (17900) (16400) (20100) (20100)
4.5 m 7950* 5950 8600* 7300* 10250* 10250* 13450* 13450*
(15') (1750) (13100) (18900) (16000) (22500) (22500) (29600) (29600)
3.0 m 8050* 5500 9150* 7000 11450* 9900 16000* 15250
(10') (17700) (12100) (20100) (15400) (25200) (21800) (35200) (33500)
1.5 m 8150* 5350 9600* 6750 12100* 9200 17150* 14400*
(5') (17900) (11800) (21100) (14800) (26600) (20200) (37700) (31700)
0m 8300* 5500 9700* 6600 12450* 9150 16850* 14200
(0') (18200) (12100) (21300) (14500) (27400) (20100) (37100) (31200)
–1.5 m 8400* 6050 9150* 6550 11900* 9100 15650* 14250 15950* 15950*
(–5') (18500) (13300) (20100) (14400) (26200) (20000) (34400) (31300) (35100) (35100)
–3.0 m 8350* 7300 10350* 9100 13500* 13300* 16500* 16500*
(–10') (18400) (16000) (22800) (20000) (29700) (29200) (36300) (36300)
–4.5 m 7700* 7700* 9850* 9850* 11600* 11600*
(–15') (16900) (16900) (21700) (21700) (25500) (25500)
Arm length 2550 mm (8'4")
6.0 m 6900* 6250 7850* 7550
(20') (15200) (13700) (17300) (16600)
4.5 m 7100* 5450 8350* 7350 9900* 9900* 12800* 12800*
(15') (15600) (12000) (18400) (16200) (21800) (21800) (28100) (28100)
3.0 m 7550* 5050 9000* 7100 11150* 10050 15500* 15500*
(10') (16600) (11100) (19800) (15600) (24500) (22100) (34100) (34100)
1.5 m 7650 4950 9500* 6850 12100* 9400 17100 14650
(5') (16800) (10900) (20900) (15100) (26600) (20700) (37600) (32200)
0m 7800 5100 9700* 6650 12550* 9250 17150 14300
(0') (17100) (11200) (21300) (14600) (27600) (20300) (37700) (31400)
–1.5 m 7900 5550 9400* 6650 12150* 9150 16200 14300 13850* 13850*
(–5') (17400) (12200) (20700) (14400) (26700) (20100) (35600) (31400) (30500) (30500)
–3.0 m 7800* 6500 8200* 6650 10700* 9000 14300* 14150* 18400* 18400*
(–10') (17160) (14300) (18000) (14600) (23500) (19800) (31400) (31100) (40500) (40500)
–4.5 m 7300* 7300* 8250* 8000 11000* 11000* 13650* 13650*
(–15') (16000) (16000) (18100) (17600) (24200) (24200) (30000) (30000)
Arm length 3900 mm (10'6")
6.0 m 4900* 4900* 7150* 7150*
(20') (10800) (10800) (15700) (15700)
4.5 m 5000* 4900 7750* 7450* 9050* 9050*
(15') (11000) (10800) (17000) (16400) (19900) (19900)
3.0 m 5300* 4550 8500* 7150* 10450* 10200 14000* 14000*
(10') (11600) (10000) (18700) (15700) (23000) (22400) (30800) (30800)
1.5 m 5850* 4450 9150* 6850* 11700* 9650 16450* 14950
(5') (12900) (9800) (20100) (15100) (25700) (21200) (36200) (32900)
0m 6650* 4500 9550* 6600* 12350* 9250 17150* 14350 8150* 8150*
(0') (14600) (9900) (21000) (14500) (27200) (20300) (37700) (31600) (17900) (17900)
–1.5 m 7300* 4850 9500* 6500* 12300* 9050 16700* 14200 13000* 13000* 9150* 9150*
(–5') (16000) (10700) (20900) (14300) (27000) (19900) (36700) (31200) (28600) (28600) (20100) (20100)
–3.0 m 7400* 5600 8700* 6500* 11500* 9050 15300* 14300 18950* 18950* 13950* 13950*
(–10') (16300) (12300) (19100) (14300) (25300) (19900) (33600) (31400) (41700) (41700) (30700) (30700)
–4.5 m 7200* 7200 9350* 9250 12650* 12400* 16750* 16750*
(–15') (15800) (15800) (20600 (20300) (27800) (29300) (36800) (36800)
Arm length 4020 mm (13'2")
6.0 m 3700* 3700*
(20') (8100) (8100)
4.5 m 3750* 3750* 7000* 7000*
(15') (8200) (8200) (15400) (15400)
3.0 m 3950* 3950* 7850* 7300* 9500* 9500* 12550* 12550* 19950* 1950*
(10') (8700) (8700) (17300) (16000) (20900) (20900) (27600) (27600) (43900) (43900)
1.5 m 4250* 3850 8650* 6900* 10900* 9800 15250* 15250* 8550* 8550*
(5') (9300) (8500) (19000) (15200) (24000) (21500) (33500) (33500) (18800) (18800)
0m 4750* 3900 9250* 6600* 11850* 9150 16700* 14500 8750* 8750*
(0') (10500) (8600) (20300) (14500) (26100) (20100) (36700) (31900) (19200) (19200)
–1.5 m 5550* 4150 9450* 6450* 12250* 9000 16950* 14100 11700* 11700* 7500* 7500*
(–5') (12200) (9100) (20800) (14200) (26900) (19800) (37300) (31000) (25700) (25700) (16500) (16500)
–3.0 m 6650* 4650 9150* 6350* 11850* 8900 16150* 14050 15950* 15950* 11250* 11250*
(–10') (14600) (10200) (20100) (14000) (26100) (19600) (35500) (30900) (35100) (35100) (24700) (24700)
–4.5 m 6650* 5650 8050* 6450* 10700* 9750 14300* 14100 19800* 20050* 15650* 15650*
(–15') (14600) (12400) (17700) (14200) (23500) (21400) (31400) (31000) (43500) (44100) (34400) (34400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-54
AH_25.book Page 55 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC400-7
Conditions: Boom: 7060 mm (23'2"), Bucket (SAE): 1.90 m3 (2.49 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3380 mm (11'1")
7.5 m 5750* 5750* 6700* 6300
(24') (12600) (12600) (14700) (13800)
6.0 m 5750* 5150 8400* 6250 9150* 8700
(19') (12600) (11300) (18500) (13700) (20100) (19100)
4.5 m 5950* 4650 8850* 6050 10100* 8350 12050* 12050*
(14') (13000) (10100) (19500) (13300) (22100) (18300) (26500) (26500)
3.0 m 6250* 4350 8850 5850 11100* 7900 13900* 11250 19450* 17450
(9') (13700) (9500) (19400) (12800) (24400) (17400) (30600) (24700) (42800) (38400)
1.5 m 6600 4250 8600 5600 11500 7550 15400* 10550 20800* 16100
(4') (14400) (9300) (18800) (12300) (25200) (16500) (33900) (23200) (45800) (35400)
0.0 m 6750 4300 8400 5450 11150 7250 15850 10100 19800* 15550
(0') (14700) (9400) (18400) (11900) (24500) (15900) (34900) (22100) (43600) (34200)
–1.5 m 7150 4600 8300 5350 11000 7050 15650 9850 21500* 15400 12950* 12950*
(–4') (15700) (10100) (18200) (11700) (24100) (15500) (34400) (21700) (47300) (33900) (28500) (28500)
–3.0 m 8050 5200 8300 5400 10950 7050 15050* 9850 19700* 15550 19000* 19000*
(–9') (17700) (11400) (18300) (11800) (24100) (15500) (33100) (21700) (43400) (34100) (41800) (41800)
–4.5 m 8550* 6400 9900* 7200 13000* 10050 16750* 15850 21750* 21750*
(–14') (18700) (14000) (21800) (15800) (28600) (22100) (36800) (34900) (47900) (47900)
–6.0 m 7700* 7700* 9050* 9050* 11950* 11950*
(–19') (16900) (16900) (19800) (19800) (26200) (26200)
Arm length 4000 mm (13'1")
7.5 m 4900* 4900* 7550* 6450
(24') (10800) (10800) (16500) (14100)
6.0 m 4900* 4650 7800* 6350
(19') (10700) (10200) (17100) (13900)
4.5 m 5050* 4200 8350* 6150 9350* 8450
(14') (11000) (9200) (18300) (13400) (20600) (18600)
3.0 m 5300* 3950 8850 5900 10500* 8000 12950* 11450 17750* 17750*
(9') (11600) (8600) (19500) (12900) (23000) (17600) (28500) (25100) (39100) (39100)
1.5 m 5750* 3850 8600 5600 11500* 7550 14700* 10650 20800* 16400
(4') (12600) (8400) (18900) (12300) (25300) (16600) (32300) (23400) (45800) (36100)
0.0 m 6150* 3900 8350 5400 11150 7200 15750* 10050 21900* 15550 8550* 8550*
(0') (13400) (8500) (18300) (11800) (24500) (15800) (34700) (22100) (48200) (34200) (18800) (18800)
–1.5 m 6450 4100 8200 5250 10900 6950 15500* 9750 21850* 15250 12500* 12500*
(–4') (14200) (9000) (18000) (11500) (23900) (15300) (34100) (21400) (48100) (33500) (27500) (27500)
–3.0 m 7200 4600 8150 5200 10800 6900 15400* 9650 20550* 15250 17350* 17350*
(–9') (15700) (10000) (17900) (11400) (23700) (15100) (33900) (21200) (45300) (33500) (38100) (38100)
–4.5 m 8200* 5500 10700* 6950 13850* 9750 18150* 15450 23400* 23400*
(–14') (18000) (12000) (23500) (15300) (30400) (21500) (39900) (34000) (51500) (51500)
–6.0 m 7850* 7350 10700* 9900 14150* 14150* 18550* 18550*
(–19') (17200) (16100) (23500) (21800) (31100) (31100) (40800) (40800)
Arm length 2400 mm (7'10")
7.5 m 9700* 7750 9850* 8600
(24') (21300) (17000) (21600) (18900)
6.0 m 9500* 6400 10300* 8450
(19') (20800) (14000) (22600) (18600)
4.5 m 8500 5650 8950 5950 11100* 8150 13500* 11650 18400* 18150
(14') (18600) (12300) (19600) (13000) (24300) (17900) (29700) (25600) (40500) (40000)
3.0 m 7950 5250 8750 5800 11750 7800 14900* 10650
(9') (17500) (11500) (19200) (12700) (25800) (17100) (32800) (23400)
1.5 m 7850 5100 8600 5600 11400 7450 16150 10350
(4') (17200) (11200) (18800) (12300) (25100) (16400) (35500) (22700)
0.0 m 8050 5250 8450 5500 11150 7250 15800 10050 15150* 15150*
(0') (17700) (11500) (18600) (12100) (24600) (15900) (34800) (22000) (33400) (33400)
–1.5 m 8750 5700 11100 7200 15600* 9950 19950* 15600
(–4') (19200) (12500) (24400) (15800) (34400) (21900) (43900) (34300)
–3.0 m 9850* 6650 10850* 7250 14000* 10100 17550* 15900 20600* 20600*
(–9') (21600) (14600) (23900) (15900) (30700) (22200) (38600) (34900) (45400) (45400)
–4.5 m 9300* 8800 10700* 10150 13700* 13700*
(–14') (20400) (19300) (23500) (22300) (30100) (30100)
2C-55
AH_25.book Page 56 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
7.5 m 8800* 7000 9100* 8700
(24') (19400) (15300) (19900) (19100)
6.0 m 8700 5800 8800* 6050 9600* 8500
(19') (19100) (12700) (19300) (13300) (21100) (18700)
4.5 m 7800 5150 8900* 5900 10450* 8150 12650* 11750 16850* 16850*
(14') (17100) (11200) (19600) (13000) (23000) (17900) (27800) (25800) (37100) (37100)
3.0 m 7350 4800 8700* 5700 11400* 7750 14400* 10950
(9') (16100) (10500) (19100) (12500) (25100) (17000) (31700) (24000)
1.5 m 7200 4650 8500* 5500 11300 7350 15650* 10250
(4') (15800) (10200) (18600) (12100) (24900) (16200) (34400) (22600)
0.0 m 7400 4750 8300* 5350 11050 7100 15650 9900 20500* 15250
(0') (16200) (10400) (18300) (11700) (24200) (15600) (34400) (21700) (45100) (33500)
–1.5 m 7950 5100 8250* 5300 10900 7000 15500 9750 20650* 15250 14800* 14800*
(–4') (17400) (11200) (18100) (11600) (24000) (15300) (34100) (21400) (45500) (33500) (32600) (32600)
–3.0 m 9100 5900 10950 7000 14400* 9800 18500* 15450 22800* 22800*
(–9') (20000) (12900) (24000) (15400) (31700) (21500) (40700) (34000) (50200) (50200)
–4.5 m 9200* 7500 11900* 10050 15150* 15150* 18700* 18700*
(–14') (20200) (16500) (26200) (22100) (33000) (33300) (41100) (41100)
–6.0 m 7850* 7850*
(–19') (17200) (17200)
2C-56
AH_25.book Page 57 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-57
AH_25.book Page 58 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
7.5 m 9850* 7000 10150* 8700
(24') (21700) (15300) (22200) (19100)
6.0 m 8700 5800 9050 6050 10700* 8500
(19') (19100) (12700) (19900) (13300) (23500) (18700)
4.5 m 7800 5150 8900 5900 11700* 8150 14050* 11750 18650* 18600
(14') (17100) (11200) (19600) (13000) (25700) (17900) (30900) (25800) (41000) (41000)
3.0 m 7350 4800 8700 5700 11750 7750 16000* 10950
(9') (16100) (10500) (19100) (12500) (25800) (17000) (35200) (24000)
1.5 m 7200 4650 8500 5500 11300 7350 16100 10250
(4') (15800) (10200) (18600) (12100) (24900) (16200) (35400) (22600)
0.0 m 7400 4750 8300 5350 11050 7100 15650 9900 22400* 15250
(0') (16200) (10400) (18300) (11700) (24200) (15600) (34400) (21700) (49300) (33500)
–1.5 m 7950 5100 82500 5300 10900 7000 15500 9750 23000* 15250 16250* 16250*
(–4') (17400) (11200) (18100) (11600) (24000) (15300) (34100) (21400) (50700) (33500) (35700) (35700)
–3.0 m 9100 5900 10950 7000 15550 9800 20700* 15450 24950* 24950*
(–9') (20000) (12900) (24000) (15400) (34200) (21500) (45500) (34000) (54900) (54900)
–4.5 m 10350* 7500 13400* 10050 17000* 15900 21000* 21000*
(–14) (22800) (16500) (29400) (22100) (37400) (35000) (46200) (46200)
–6.0 m 8950* 8950*
(–19) (19600) (19600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-58
AH_25.book Page 59 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC400LC-7
Conditions: Boom: 7060 mm (23'2"), Bucket (SAE): 1.90 m3 (2.49 cu.yd), Shoes: 700 mm (28") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3380 mm (11'1")
7.5 m 5750* 5750* 6700* 6500
(24') (12600) (12600) (14700) (14200)
6.0 m 5750* 5350 8400* 6450 9150* 8950
(19') (12600) (11700) (18500) (14100) (20100) (19700)
4.5 m 5950* 4800 8850* 6250 10100* 8600 12050* 12050*
(14') (13000) (10500) (19500) (13700) (22100) (18900) (26500) (26500)
3.0 m 6250* 4500 9400* 6050 11100* 8200 13900* 11600 19450* 17950
(9') (13700) (9900) (20700) (13300) (24400) (17900) (30600) (25400) (42800) (39500)
1.5 m 6800 4400 9850 5850 12000* 7800 15400* 10900 20800* 16600
(4') (14900) (9600) (21700) (12800) (26400) (17100) (33900) (23900) (45800) (36600)
0.0 m 7650 4500 9700 5650 12500* 7500 16150* 10400 19800* 16050
(0') (16800) (9800) (21300) (12400) (27500) (16400) (35500) (22900) (43600) (35300)
–1.5 m 8300 4800 9600 5550 12500* 7300 16050* 10200 21500* 15900 12950* 12950*
(–4') (18200) (10500) (21000) (12200) (27400) (16100) (35300) (22400) (47300) (35000) (28500) (28500)
–3.0 m 8700 5400 9050* 5600 11750* 7300 15050* 10200 19700* 16050 19000* 19000*
(–9') (19100) (11900) (19900) (12200) (25800) (16000) (33100) (22400) (43400) (35300) (41800) (41800)
–4.5 m 8550* 6650 9900* 7450 13000* 10400 16750* 16350 21750* 21750*
(–14') (18700) (14500) (21800) (16300) (28600) (22800) (36800) (36000) (47900) (47900)
–6.0 m 7700* 7700* 9050* 9050* 11950* 11950*
(–19') (16900) (16900) (19800) (19800) (26200) (26200)
Arm length 4000 mm (13'1")
7.5 m 4900* 4900* 7550* 6650
(24') (10800) (10800) (16500) (14600)
6.0 m 4900* 4850 7800* 6550
(19') (10700) (10600) (17100) (14400)
4.5 m 5050* 4350 8350* 6350 9350* 8700
(14') (11000) (9600) (18300) (13900) (20600) (19100)
3.0 m 5300* 4100 8950* 6100 10500* 8250 12950* 11750 17750* 17750*
(9') (11600) (9000) (19700) (13300) (23000) (18100) (28500) (25900) (39100) (39100)
1.5 m 5750* 4000 9550* 5800 11500* 7800 14700* 11000 20800* 16900
(4') (12600) (8700) (2100) (12800) (25300) (17100) (32300) (24100) (45800) (37200)
0.0 m 6400* 4050 9650 5600 12200* 7450 15750* 10400 21900* 16050 8550* 8550*
(0') (14000) (8900) (21200) (12300) (26800) (16300) (34700) (22900) (48200) (35300) (18800) (18800)
–1.5 m 7400* 4300 9500 5450 12400* 7250 16000* 10100 21850* 15750 12500* 12500*
(–4') (16300) (9400) (20800) (12000) (27300) (15900) (35200) (22200) (48100) (34600) (27500) (27500)
–3.0 m 8200* 4750 9450 5450 12000* 7150 15400* 10000 20550* 15750 17350* 17350*
(–9') (18000) (10400) (20700) (11900) (26400) (15700) (33900) (22000) (45300) (34600) (38100) (38100)
–4.5 m 8200* 5700 10700* 7200 13850* 10100 18150* 15950 23400* 23400*
(–14') (18000) (12500) (23500) (15800) (30400) (22200) (39900) (35100) (51500) (51500)
–6.0 m 7850* 7600 10700* 10250 14150* 14150* 18550* 18550*
(–19') (17200) (16700) (23500) (22500) (31100) (31100) (40800) (40800)
Arm length 2400 mm (9'6")
7.5 m 9700* 8000 9850* 8900
(24') (21300) (17600) (21600) (19500)
6.0 m 9500* 6600 10300* 8750
(19') (20800) (14500) (22600) (19200)
4.5 m 9450* 5850 9650* 6150 11100* 8400 13500* 12000 18400* 18400*
(14') (20800) (12800) (21200) (13500) (24300) (18500) (29700) (26300) (40500) (40500)
3.0 m 9150 5450 10050* 6000 11950* 8050 14900* 10950
(9') (20100) (11900) (22000) (13100) (26200) (17600) (32800) (24100)
1.5 m 9000 5300 9850 5850 12550* 7700 16150* 10650
(4') (19800) (11600) (21700) (12800) (27600) (16900) (35600) (23400)
0.0 m 9250 5450 9750 5700 12750* 7500 16300* 10400 15150* 15150*
(0') (20400) (11900) (21400) (12500) (28000) (16500) (35900) (22800) (33400) (33400)
–1.5 m 9900* 5900 12250* 7450 15600* 10300 19950* 16100
(–4') (21800) (12900) (27000) (16300) (34400) (22700) (43900) (35400)
–3.0 m 9850* 6900 10850* 7500 14000* 10450 17550* 16400 20600* 20600*
(–9') (21600) (15100) (23900) (16500) (30700) (22900) (38600) (36000) (45400) (45400)
–4.5 m 9300* 9100 10700* 10500 13700* 13700*
(–14') (20400) (19900) (23500) (23100) (30100) (30100)
2C-59
AH_25.book Page 60 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
7.5 m 8800* 7200 9100* 8950
(24') (19400) (15800) (19900) (19700)
6.0 m 8700* 6000 8800* 6250 9600* 8750
(19') (19100) (13100) (19300) (13700) (21100) (19200)
4.5 m 8700* 5300 9150* 6150 10450* 8400 12650* 12100 16850* 16850*
(14') (19100) (11700) (20100) (13400) (23000) (18500) (27800) (26600) (37100) (37100)
3.0 m 8450 4950 9600* 5900 11400* 8000 14400* 11300
(9') (18500) (10900) (21100) (13000) (25100) (17600) (31700) (24800)
1.5 m 8300 4850 9750 5700 12150* 7600 15650* 10600
(4') (18200) (10600) (21400) (12500) (26700) (16700) (34400) (23300)
0.0 m 8500 4950 9600 5550 12500* 7350 16100* 10200 20500* 15750
(0') (18700) (10800) (21100) (12200) (27500) (16100) (35400) (22500) (45100) (34600)
–1.5 m 9200 5300 9550 5500 12250* 7250 15700* 10100 20650* 15750 14800* 14800*
(–4') (20100) (11600) (20900) (12100) (27000) (15900) (34600) (22100) (45500) (34600) (32600) (32600)
–3.0 m 9400* 6100 11250* 7300 14400* 10150 18500* 15950 22800* 22800*
(–9') (20700) (13400) (24700) (16000) (31700) (22300) (40700) (35100) (50200) (50200)
–4.5 m 9200* 7800 11900* 10400 15150* 15150* 18700* 18700*
(–14') (20200) (17100) (26200) (22900) (33300) (33300) (41100) (41100)
–6.0 m 7850* 7850*
(–19') (17200) (17200)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-60
AH_25.book Page 61 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-61
AH_25.book Page 62 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
7.5 m 9850* 7200 10150* 8950
(24') (21700) (15800) (22200) (19700)
6.0 m 9750* 6000 9850* 6250 10700* 8750
(19') (21400) (13100) (21600) (13700) (23500) (19200)
4.5 m 8950 5300 10200 6150 11700* 8400 14050* 12100 18650* 18650*
(14') (19700) (11700) (22400) (13400) (25700) (18500) (30900) (26600) (41000) (41000)
3.0 m 8450 4950 1000 5900 12750* 8000 16000* 11300
(9') (18500) (10900) (21900) (13000) (28000) (17600) (35200) (24800)
1.5 m 8300 4850 9750 5700 13050 7600 17450* 10600
(4') (18200) (10600) (21400) (12500) (28700) (16700) (38400) (23300)
0.0 m 8500 4950 9600 5550 12750 7350 17950* 10200 22400* 15750
(0') (18700) (10800) (21100) (12200) (28100) (16100) (39500) (22500) (49300) (34600)
–1.5 m 9200 5300 9550 5500 12650 7250 17550* 10100 23000* 15750 16250* 16250*
(–4') (20100) (11600) (20900) (12100) (27800) (15900) (38600) (22100) (50700) (34600) (35700) (35700)
–3.0 m 10550 6100 12600* 7300 16150* 10150 20700* 15950 24950* 24950*
(–9') (23100) (13400) (27700) (16000) (35500) (22300) (45500) (35100) (54900) (54900)
–4.5 m 10350* 7800 13400* 10400 17000* 16400 21000* 21000*
(–14') (22800) (17100) (29400) (22900) (37400) (36100) (46200) (46200)
–6.0 m 8950* 8950*
(–19') (19600) (19600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-62
AH_25.book Page 63 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC400SE-6
Conditions: Boom: 7060 mm (23'2"), Bucket (SAE): 2.8 m3 (3.66 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2490 mm (7'10")
7.5 m *9100 7350 *9300 8250
(25') (20050) (16200) (20500) (18200)
6.0 m *8900 5900 *9750 8100
(20') (19600) (13000) (21500) (17850)
4.6 m *8850 5150 *9050 5500 *10500 7750 *12950 11250 *17750 *11750
(15') (19500) (11350) (19950) (12150) (23150) (17100) (28550) (24800) (39150) (39150)
3.0 m 7550 4750 8350 5300 *11300 7300 *14150 10000
(10') (16650) (10450) (18450) (11700) (24900) (16100) (31200) (22050)
1.5 m 7400 4600 8150 5100 *11900 6950 *15450 9750
(5') (16300) (10150) (17900) (11250) (26250) (15300) (34050) (21500)
0m 7600 4700 8000 5000 *10750 6700 *15600 9400 *18450 14650
(0') (16800) (10350) (17700) (11000) (23700) (14750) (34400) (20700) (40700) (32300)
–1.5 m *9250 5150 *11600 6600 *14900 9350 *19100 14800
(–5') (20400) (11350) (25550) (14550) (32850) (20600) (42100) (32650)
–3.0 m *9200 6100 *10200 6700 *13250 9500 *16700 15150 *19500 *19500
(–10') (20300) (13450) (22500) (14750) (29200) (20950) (36800) (33400) (43000) (43000)
–4.6 m *8600 8250 *9850 9500 *12900 *12900
(–15') (18950) (18200) (21700) (20950) (28450) (28450)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-63
AH_25.book Page 64 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-64
AH_25.book Page 65 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-65
AH_25.book Page 66 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-66
AH_25.book Page 67 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-67
AH_25.book Page 68 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC450-7
Conditions: Boom: 7060 mm (23'2"), Bucket (SAE): 1.90 m3 (2.49 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3380 mm (11'1")
7.5 m 5550* 5550* 6600* 5900
(24') (12100) (12100) (14500) (12900)
6.0 m 5550* 4750 8800* 5850 9600* 8400
(19') (12100) (10400) (19300) (12900) (21100) (18500)
4.5 m 5750* 4200 8750 5700 10650* 8050 12800* 11850
(14') (12600) (9200) (19300) (12500) (23400) (17600) (28100) (26000)
3.0 m 6100* 3900 8500 5450 11700 7600 14800* 10950 20800* 17200
(9') (13400) (8500) (18700) (12000) (25700) (16600) (32600) (24100) (45800) (37800)
1.5 m 6200 3800 8250 5250 11200 7150 16150 10200 23400* 15700
(4') (13600) (8300) (18100) (11400) (24600) (15700) (35500) (22400) (51500) (34600)
0.0 m 6350 3900 8050 5050 10850 6850 15600 9650 23050* 15050
(0') (13900) (8500) (17700) (11000) (23800) (15000) (34300) (21200) (50700) (33100)
–1.5 m 6800 4200 7950 4950 10650 6650 15300 9450 23000* 14900 15050* 15050*
(–4') (14900) (9100) (17400) (10800) (23400) (14600) (33700) (20700) (50700) (32800) (33100) (33100)
–3.0 m 7700 4800 7950 4950 10650 6650 15300 9450 21050* 15050 22200* 22200*
(–9') (16900) (10500) (17500) (10900) (23400) (14500) (33700) (20700) (46400) (33100) (48800) (48800)
–4.5 m 8900* 6000 10450* 6800 13800* 9650 17850* 15450 23300* 23300*
(–14') (19600) (13100) (23000) (14900) (30400) (21200) (39300) (34000) (51200) (51200)
–6.0 m 8000* 8000* 9350* 9350* 12650* 12650*
(–19') (17600) (17600) (20500) (20500) (27900) (27900)
PC450LC-7
Conditions: Boom: 7060 mm (23'2"), Bucket (SAE): 1.90 m3 (2.49 cu.yd), Shoes: 600 mm (24") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3380 mm (11'1")
7.5 m 5550* 5550* 6600* 6000
(24') (12100) (12100) (14500) (13200)
6.0 m 5550* 4850 8800* 6000 9600* 8550
(19') (12100) (10600) (19300) (13100) (21100) (18800)
4.5 m 5750* 4300 9300* 5800 10650* 8200 12800* 12000
(14') (12600) (9400) (20400) (12700) (23400) (17900) (28100) (26400)
3.0 m 6100* 4000 96500 5550 11750* 7700 14800* 11150 20800* 17450
(9') (13400) (8700) (21200) (12200) (25800) (16900) (32600) (24500) (45800) (38400)
1.5 m 6700 3900 9400 5350 12700* 7300 16450* 10350 23400* 16000
(4') (14700) (8500) (20700) (11700) (27900) (16000) (36100) (22800) (51500) (35100)
0.0 m 7250 4000 9200 5150 12400 6950 17250* 9850 23050* 15350
(0') (15900) (8700) (20200) (11300) (27300) (15300) (37900) (21600) (50700) (33700)
–1.5 m 7750 4300 9100 5050 12200 6800 17100* 9600 23000* 15200 15050* 15050*
(–4') (17100) (9300) (19900) (11000) (26800) (14900) (37600) (21100) (50700) (33400) (33100) (33100)
–3.0 m 8800 4900 9100 5050 12200 6750 16050* 9600 21050* 15350 22200* 22200*
(–9') (19300) (10700) (20000) (11100) (26800) (14800) (35300) (21100) (46400) (33700) (48800) (48800)
–4.5 m 8900* 6100 10450* 6950 13800* 9800 17850* 15700 23300* 23300*
(–14') (19600) (13400) (23000) (15200) (30400) (21600) (39300) (34600) (51200) (51200)
–6.0 m 8000* 8000* 9350* 9350* 12650* 12650*
(–19') (17600) (17600) (20500) (20500) (27900) (27900)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-68
AH_25.book Page 69 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-69
AH_25.book Page 70 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-70
AH_25.book Page 71 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-71
AH_25.book Page 72 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-72
AH_25.book Page 73 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC600-7
Conditions: Boom: 7660 mm (25'2"), Bucket (SAE): 2.70 m3 (3.53 cu.yd), Shoes: 600 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3500 mm (11'6")
9.1 m 8000* 8000*
(30') (17600) (17600)
6.1 m 7900* 7250 10150* 8950 11450* 11450*
(20') (17400) (16000) (22400) (19700) (25300) (25300)
3.0 m 8150 6050 11000 8300 14000* 11400 18200* 16350
(10') (18000) (13300) (24200) (18300) (30800) (25100) (40100) (86100)
0m 8200 6050 10350 7700 13500 9950 20100* 14800 14500* 14500*
(0') (18100) (18300) (22900) (17000) (29800) (21900) (44300) (32700) (32000) (32000)
–3.0 m 10150 7550 10350 7650 13500 9950 18100* 14800 23150* 23150* 20950* 20950*
(–10') (22400) (16600) (22800) (16900) (29800) (22000) (39900) (32600) (51000) (51000) (46200) (46200)
–6.1 m 9250* 9250* 10400* 10400* 13550* 13550*
(–20') (20500) (20500) (22900) (22900) (29800) (29800)
Conditions: Boom: 7300 mm (23'11"), Bucket (SAE): 2.80 m3 (3.66 cu.yd), Shoes: 600 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3500 mm (11'6")
9.1 m 7550* 7550* 8400* 8400*
(30') (16600) (16600) (18500) (18500)
6.1 m 7450* 7450* 10100* 8650 11300* 11300*
(20') (16400) (16400) (22300) (19100) (24900) (24900)
3.0 m 8550* 6300 10850 8150 13800* 11400 17200* 15900 23350* 23350*
(10') (18800) (18900) (24000) (17900) (30400) (25100) (38000) (35100) (51500) (51500)
0m 8700 6350 10300 7600 14100 10450 20000* 15050 19500* 19500*
(0') (19200) (14000) (22700) (16800) (31000) (23000) (44100) (33200) (43000) (43000)
–3.0 m 10900* 8150 13750* 10300 17900* 14950 23300* 23300* 23850* 23850*
(–10') (24000) (18000) (30300) (22700) (39500) (38000) (51300) (51800) (52500) (52500)
2C-73
AH_25.book Page 74 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC600-7
Conditions: Boom: 6600 mm (21'8"), Bucket (SAE): 3.5 m3 (4.58 cu.yd), Shoes: 600 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
9.1 m 8750* 8750*
(30') (19300) (19300)
6.1 m 8300* 8300* 11700* 11700*
(20') (18300) (18300) (25800) (25800)
3.0 m 9300 7050 10850 8150 13950* 11550 17650* 17100 24700* 24700*
(10') (20500) (15600) (24000) (17900) (30800) (25500) (38900) (37700) (54500) (54500)
0m 9650 7100 10350 7650 14150 10550 19000* 13900 28100* 24650*
(0') (21300) (15700) (22800) (16800) (31200) (23200) (41900) (30600) (61900) (54400)
–3.0 m 11650 9350 13200* 10400 16800* 13850 23750* 23750* 29900* 29900*
(–10') (25700) (20700) (29200) (23000) (37100) (30600) (52300) (52300) (65900) (65900)
2C-74
AH_25.book Page 75 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC600LC-7
Conditions: Boom: 7660 mm (25'2"), Bucket (SAE): 2.70 m3 (3.53 cu.yd), Shoes: 600 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3500 mm (11'6")
9.1 m 8000* 8000*
(30') (17600) (17600)
6.1 m 7900* 7400 10150* 9100 11450* 11450*
(20') (17400) (16400) (22400) (20100) (25300) (25300)
3.0 m 8900* 6200 11500* 8450 14000* 11650 18200* 16650
(10') (19700) (13600) (25400) (18700) (30800) (25600) (40100) (36800)
0m 9500 6200 12000 7900 15000* 10200 20100* 15150 14500* 14500*
(0') (21000) (13700) (26400) (17400) (33100) (22400) (44300) (33400) (32000) (32000)
–3.0 m 10600* 7700 10850* 7850 13850* 10200 18100* 15100 23150* 23150* 20950* 20950*
(–10') (23300) (17000) (23900) (17300) (80600) (22500) (39900) (33300) (51000) (51000) (46200) (46200)
–6.1 m 9250* 9250* 10400* 10400* 13550* 13550*
(–20') (20500) (20500) (22900) (22900) (29800) (29800)
Conditions: Boom: 7300 mm (23'11"), Bucket (SAE): 2.80 m3 (3.66 cu.yd), Shoes: 600 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3500 mm (11'6")
9.1 m 7550* 7550* 8400* 8400*
(30') (16600) (16600) (18500) (18500)
6.1 m 7450* 7450* 10100* 8850 11300* 11300*
(20') (16400) (16400) (22300) (19500) (24900) (24900)
3.0 m 8550* 6450 11350* 8300 13800* 11600 17200* 16200 23350* 23350*
(10') (18800) (14300) (25100) (18300) (30400) (25600) (38000) (35700) (51500) (51500)
0m 10100 6500 11900 7800 15250* 10650 20000* 15350 19500* 19500*
(0') (22200) (14400) (26800) (17200) (33600) (23500) (44100) (33800) (48000) (48000)
–3.0 m 10900* 8350 13750* 10550 17900* 15250 23300* 23300* 23850* 23850*
(–10') (24000) (18400) (30300) (23200) (39500) (33600) (51300) (51300) (52500) (52500)
2C-75
AH_25.book Page 76 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC600LC-7
Conditions: Boom: 6600 mm (21'8"), Bucket (SAE): 3.5 m3 (4.58 cu.yd), Shoes: 600 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2900 mm (9'6")
9.1 m 8750* 8750*
(30') (19300) (19300)
6.1 m 8300* 8300* 11700* 11700*
(20') (18300) (18300) (25800) (25800)
3.0 m 9300* 7200 11700* 8350 13950* 11800 17650* 17400 24700* 24700*
(10') (20500) (15900) (25800) (18400) (30800) (26000) (38900) (38400) (54500) (54500)
0m 11200 7300 11950 7800 15400* 10750 19000* 14200 28100* 25150
(0') (24600) (16100) (26400) (17300) (33900) (23700) (41900) (31300) (61900) (55500)
–3.0 m 11650* 9350 13200* 10650 16800* 14200 23750* 23750* 29900* 29900*
(–10') (25700) (20700) (29200) (23500) (37100) (31300) (52300) (52300) (65900) (65900)
2C-76
AH_25.book Page 77 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
2C-77
AH_25.book Page 78 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3500 mm (11'6")
9.1 m *8000 *8000
(30') (17600) (17600)
6.1 m *7900 7400 *10150 9100 *11450 *11450
(20') (17350) (16250) (22300) (20000) (25200) (25200)
3.0 m *8900 6200 *11500 8450 *14000 11650 *18200 16650
(10') (19550) (13600) (25300) (18600) (30800) (25600) (40000) (36600)
0m 9500 6200 12000 7900 *15000 10200 *20100 15150 *14500 *14500
(0') (20900) (13600) (26400) (17350) (33000) (22400) (44000) (33300) (31900) (31900)
–3.0 m *10600 7700 *10850 7850 *13850 10200 *18100 15100 *23150 *23150 *20950 *20950
(–10') (23300) (16900) (23850) (17250) (30450) (22400) (39800) (33200) (50900) (50900) (46100) (46100)
–6.1 m *9250 *9250 *10400 *10400 *13550 *13550
(–20') (20350) (20350) (22850) (22850) (29800) (29800)
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3500 mm (11'6")
9.1 m *8850 *8850
(30') (19450) (19450)
6.1 m *8750 7400 *11350 9100 *12750 *12750
(20') (19250) (16250) (24950) (20000) (28050) (28050)
3.0 m *9400 6200 12600 8450 *15550 11650 *20150 16650
(10') (20650) (13600) (27700) (18600) (34200) (25600) (44300) (36600)
0m 9500 6200 12000 7900 15700 10200 *22300 15150 *15900 *15900
(0') (20900) (13600) (26400) (17350) (34500) (22400) (49050) (33300) (34950) (34950)
–3.0 m 11750 7700 11950 7850 *15550 10200 *20200 15100 *25750 24900 *22800 *22800
(–10') (25850) (16900) (26300) (17250) (34200) (22400) (44400) (33200) (56650) (54750) (50150) (50150)
–6.1 m *10550 *10550 *11800 *15300 *15300
(–20') (23200) (23200) (25950) (33650) (33650)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-78
AH_25.book Page 79 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC750-7
Conditions: Boom: 8200 mm (26'11"), Bucket (SAE): 3.1 m3 (4.05 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.0 m *9350 *8650 *12950 12700 *15150 *15150 *18900 *18900
(19') (20600) (19100) (28500) (28000) (33400) (33400) (41700) (41700)
3.0 m 9650 7350 14750 11400 *18450 14850 *25700 21900
(9') (21300) (16200) (32500) (25200) (40700) (32800) (56700) (48300)
0m 9800 7350 13750 10450 18550 14100 26900 20100
(0') (21600) (16200) (30300) (23000) (40900) (31000) (59300) (44300)
–3.0 m 12000 9100 13500 10250 18300 13850 *24850 20150 *29350 *29350 *21350 *21350
(–9') (26500) (20000) (29800) (22600) (40300) (30500) (54800) (44500) (64700) (64700) (47100) (47100)
–6.0 m *14350 *14350 *17000 *17000
(–19') (31600) (31600) (37500) (37500)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.0 m *10550 8650 *14800 12700 *17250 *17250 *21350 *21350
(19') (23300) (19100) (32700) (28000) (38000) (38000) (47100) (47100)
3.0 m 9650 7350 14750 11400 19400 14850 28850 21900
(9') (21300) (16200) (32500) (25200) (42800) (32800) (63700 (48300)
0m 9800 7350 13750 10450 18550 14100 26900 20100
(0') (21600) (16200) (30300) (23000) (40900) (31000) (59300) (44300)
–3.0 m 12000 9100 13500 10250 18300 13850 26950 20150 *32500 *32500 *23750 *23750
(–9') (26500) (20000) (29800) (22600 (40300) (30500) (59500) (44500) (71700) (71700) (52300) (52300)
–6.0 m *16650 *16650 *19700 *19700
(–19') (36800) (36800) (43400) (43400)
Conditions: Boom: 8200 mm (26'11"), Bucket (SAE): 3.1 m3 (4.05 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 12.0 m (39') 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 5600 mm (18'4")
6.0 m *4550 *4550 *6850 *6850
(19') (10000) (10000) (15100) (15100)
3.0 m *5300 *5300 *9500 7400 *12650 *12650 *15500 *15500 *20450 *20450
(9') (11700) (11700) (20900) (16300) (27900) (27900) (34200) (34200) (45100) (45100)
0m *6950 5800 9000 6750 *15000 11600 19050 15750 *25600 22550 *13650 *13650
(0') (15300) (12800) (19800) (14900) (33100) (25600) (42000) (34700) (56400) (49700) (30100) (30100)
–3.0 m 8950 6650 14250 10850 19350 14700 -26100 *21350 *21100 *21100 *13900 *13900
(–9') (19700) (14700) (31400) (23900) (42700) (32400) (57600) (47100) (46500) (46500) (30600) (30600)
–6.0 m *11750 9650 *13450 10950 *16550 13950 *22400 21700 *29850 *29850 *25250 *25250
(–19') (25900) (21200) (29600) (24100) (36400) (30800) (49400) (47900) (65800) (65800) (55600) (55600)
2C-79
AH_25.book Page 80 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC750-7
Conditions: Boom: 8200 mm (26'11"), Bucket (SAE): 3.1 m3 (4.05 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 12.0 m (39') 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 4600 mm (15'1")
6.0 m *7500 7500 *11500 *11500
(19') (16600) (16500) (25400) (25400)
3.0 m 8450 6350 8650 6500 *14150 11650 *17500 15950 *23400 22950
(9') (18700) (14000) (19000) (14300) (31200) (25700) (38600) (35200) (51600) (50600)
0m 8450 6250 13700 10400 18600 14100 *27000 20200 *13600 *13600
(0') (18600) (13800) (30200) (23000) (41000) (31100) (59500) (44500) (30000) (30000)
–3.0 m 10000 7450 13200 9900 17950 13500 *25950 19700 *25600 *25600 *17800 *17800
(–9') (22000) (16400) (29100) (21900) (39600) (29800) (57300) (43400) (56400) (56400) (39300) (39300)
–6.0 m *13850 12100 *15800 14000 *20350 *20350 *26300 *26300
(–19') (30500) (26600) (34800) (30900) (44900) (44900) (58000) (58000)
2C-80
AH_25.book Page 81 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC750SE-7
Conditions: Boom: 7100 mm (23'4"), Bucket (SAE): 4.0 m3 (5.23 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2920 mm (9'7")
6.0 m *13600 10850 *13800 11600 *15600 *15600 *18800 *18800
(19') (30000) (23900) (30400) (25600) (34400) (34400) (41500) (41500)
3.0 m 11800 8900 14100 10750 *19050 15100 *25300 21950
(9') (26000) (19600) (31100) (23700) (42000) (33300) (55800) (48400)
0m 12250 9200 13350 10050 18350 13850 27000 20150 *27550 *27550
(0') (27000) (20300) (29400) (22100) (40400) (30500) (59600) (44400) (60800) (60800)
–3.0 m *16000 12800 *17500 13950 *23150 20450 *29900 *29900 *37500 *37500
(–9') (35200) (28200) (38600) (30800) (51000) (45100) (66000) (66000) (82700) (82700)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2920 mm (9'7")
6.0 m 14050 10850 15000 11600 *17800 16950 *21350 *21350
(19') (31000) (23900) (33100) (25600) (39300) (37400) (47100) (47100)
3.0 m 11800 8900 14100 10750 19650 15100 *28750 21950
(9') (26000) (19600) (31100) (23700) (43300) (33300) (63400) (48400)
0m 12250 9200 13350 10050 18350 13850 27000 20150 *30600 *30600
(0') (27000) (20300) (29400) (22100) (40400) (30500) (59600) (44400) (67400) (67400)
–3.0 m 16900 12800 18450 13950 *26500 20450 *34200 *34200 *42950 *42950
(–9') (37200) (28200) (40700) (30800) (58400) (45100) (75400) (75400) (94600) (94600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-81
AH_25.book Page 82 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.0 m (30') 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2920 mm (9'7")
6.0 m 11100* 11100* 14300* 13900 16300* 16300*
(20') (24400) (24400) (31400) (30600) (35800) (35800)
3.0 m 12100* 9500 15550* 12800 18950* 17650 23950* 23950*
(10') (26600) (20900) (34200) (28100) (41700) (38800) (52700) (52700)
0m 12850 9650 15750* 11850 19800* 15950 25750* 22850 29400* 29400*
(0') (28300) (21200) (34600) (26100) (43500) (35000) (56600) (50300) (64700) (64700)
–3.0 m 12100* 12100* 16450* 15750 21300* 21300* 27100* 27100* 33250* 33250*
(–10') (26600) (26600) (36200) (34600) (46800) (46800) (59600) (59600) (73100) (73100)
–6.0 m
(–20')
A MAX 9.0 m (30') 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2920 mm (9'7")
6.0 m 12450* 11200 16350* 13900 18550* 18550*
(20') (27400) (24600) (36000) (30600) (40800) (40800)
3.0 m 12600 9500 16750 12800 21600* 17650 27200* 25000
(10') (27700) (20900) (36800) (28100) (47500) (38800) (59800) (55000)
0m 12850 9650 15750 11850 21200 15950 29350* 22850 32500* 32500*
(0') (28300) (21200) (34600) (26100) (46600) (35100) (64500) (50300) (71500) (71500)
–3.0 m 14100* 12250 19000* 15750 24500* 22650 31150* 31150* 38350* 38350*
(–10') (31000) (26900) (41800) (34600) (53900) (49800) (68500) (68500 (84400) (84400)
–6.0 m
(–20')
Conditions: Boom: 8200 mm (26'11"), Bucket (SAE): 3.6 m3 (4.71 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.0 m (30') 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.0 m 9750* 8400 12800* 12800* 15000* 15000*
(20') (21400) (18500) (28100) (28100) (33000) (33000)
3.0 m 9700 14500* 12750 17850* 17350 23350* 23350*
(10') (21300) (31900) (28000) (39300) (38200) (51400) (51400)
0m 9700 7100 15250* 11400 19050* 15250 24650* 21600 16800* 16800*
(0') (21300) (15600) (33500) (25100) (41900) (33500) (54200) (47500) (36900) (36900)
–3.0 m 10300* 8350 13800* 10950 17500* 14650 21750* 21100 27300* 27300* 21950* 21950*
(–10') (22600) (18400) (30300) (24100) (38500) (32200) (47800) (46400) (60000) (60000) (47200) (47200)
–6.0 m 8850* 8850* 10800* 10800* 14050* 14050* 16900* 16900*
(–20') (19500) (19500) (23700) (23700) (30900) (30900) (37200) (37200)
A MAX 9.0 m (30') 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.0 m 10950* 8400 14700* 14400 17100* 17100*
(20') (24100) (18500) (32300) (31700) (37600) (37600)
3.0 m 9700 7150 16650* 12750 20400* 17350 26600* 24700
(10') (21300) (15700) (36600) (28000) (44900) (38200) (58500) (54300)
0m 9700 7100 15300 11400 20500 15250 28250* 21600 18700* 18700*
(0') (21300) (15600) (33600) (25100) (45100) (33500) (62100) (47500) (41100) (41100)
–3.0 m 11350 8350 14800 10950 19850 14650 25100* 21100 31550* 31550* 24350* 24350*
(–10') (25000) (18400) (32500) (24100) (43700) (32200) (55200) (46400) (69400) (69400) (53600) (53600)
–6.0 m 10650* 10650* 12900* 12900* 16650* 16500* 20000* 20000*
(–20') (23400) (23400) (28400) (28400) (36600) (36600) (44000) (44000)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-82
AH_25.book Page 83 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.1 m 12200* 11550 *16050 13250 *18150 *18150 *27150 24750
(20') (26900) (25500) (35400) (29200) (40000) (40000) (59800) (54500)
3.0 m 12800 9600 16650 12800 *21150 17000 *27150 24750
(10') (28200) (21200) (36700) (28200) (46600) (37500) (50800) (54500)
0.0 m 13050 9700 16100 12250 20500 15400 *28950 22100 *37950 *36150
(0') (28700) (21400) (35500) (27000) (45300) (34000) (63800) (48800) (83700) (79600)
–3.0 m *14900 12550 15150 13500 *18500 15200 *24100 21900 *30800 *30800 *38300 *38300
(–10') (32900) (27700) (33400) (25000) (40700) (33500) (53100) (48300) (67900) (67900) (84500) (84500)
–6.1 m
(–20')
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
A MAX 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
9.1 m 9800* 9800* 10300* 10300*
(30') (21600) (21600) (22700) (22700)
6.1 m 10550* 10500 14550* 14500 16850* 16850* 20750* 20750*
(20') (23200) (23100) (32100) (32000) (37200) (37200) (45800) (45800)
3.0 m *12650* 9000 17150* 13250 21200* 17900 28450* 25150
(10') (27900) (19800) (37800) (29300) (46800) (39400) (62700) (55500)
0.0 m 13950 9050 18700* 12300 23400* 16450 30600* 23300
(0') (30800) (20000) (41200) (27200) (51600) (36300) (67400) (51400)
–3.0 m 16100* 11500 17450* 12100 22000* 16200 27850* 23350 33550* 33550* 24200* 24200*
(–10') (35500) (24600) (38500) (26700) (48500) (35800) (61400) (51500) (74000) (74000) (53300) (53300)
–6.1 m 16600* 16600* 18900* 18900*
(–20') (36700) (36700) (41700) (41700)
Conditions: Boom: 8200 mm (26'11"), Bucket (SAE): 2.8 m3 (3.6 cu.yd), Shoes: 1010 mm (40")
(Heavy-lifting: "ON") Counterweight: 12000 kg (26450 lb) unit: kg (lb)
A MAX 12.2 m (40') 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 4600 mm (15'1")
9.1 m 8050* 8050*
(30') (17700) (17700)
6.1 m 8550* 8550 11900* 11000 13000* 13000*
(20') (18900) (18900) (26200) (24300) (28700) (28700)
3.0 m 10150* 7900 13600* 10200 15900* 13500 19550* 18300 25900* 25900*
(10') (22400) (17400) (30000) (22500) (35100) (29700) (43100) (40400) (57100) (57100)
0m 12250 7850 14550* 9450 18100* 12300 22700* 16500 30100* 23400 15900* 15900*
(0') (27000) (17300) (32000) (20800) (39900) (27100) (50100) (36300) (66400) (51600) (35100) (35100)
–3.0 m 14450 9300 18000* 11800 22600* 15850 29100* 22850 29300* 29300*
(–10') (31800) (20500) (39700) (26000) (49800) (35000) (64100) (50400) (64600) (64600)
–6.1 m *16150* 14900 17600* 16400* 22750* 22750* 29400* 29400*
(–20') (35600) (32900) (38900) (36200) (50200) (50200) (64800) (64800)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-83
AH_25.book Page 84 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC800-7
Conditions: Boom: 8040 mm (26'11"), Bucket (SAE): 3.4 m3 (4.45 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.0 m *10550 9050 *11950 *11950 *14000 *14000 *17500 *17500
(19') (23200) (20000) (26400) (26400) (30900) (30900) (38600) (38600)
3.0 m 10100 7650 *14150 12050 *17700 16500 *24000 23400
(9') (22300) (16800) (31200) (26600) (39100) (36300) (52900) (51600)
0m 10250 7700 14450 11000 19600 14850 *25900 21300
(0') (22600) (16900) (31900) (24200) (43200) (32800) (57100) (47000)
–3.0 m 12700 9600 14250 10800 *18400 14650 *23550 21400 *30250 *30250 *28050 *28050
(–9') (28000) (21100) (31500) (23800) (40600) (32300) (51900) (47200) (66700) (66700) (61900) (61900)
–6.0 m *12850 *12850 *15550 *15550
(–19') (28400) (28400) (34300) (34300)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3600 mm (11'10")
6.0 m 11750 9050 *13850 13450 *16100 *16100 *19900 *19900
(19') (25900) (20000) (30500) (29700) (35500) (35500) (43900) (43900)
3.0 m 10100 7650 15600 12050 *20350 16500 *27400 23400
(9') (22300) (16800) (34400) (26600) (44900) (36300) (60500) (51600)
0m 10250 7700 14450 11000 19600 14850 28500 21300
(0') (22600) (16900) (31900) (24200) (43200) (32800) (62900) (47000)
–3.0 m 12700 9600 14250 10800 19350 14650 *27050 21400 *34700 *34700 *31100 *31100
(–9') (28000) (21100) (31500) (23800) (42700) (32300) (59700) (47200) (76500) (76500) (68600) (68600)
–6.0 m *15150 *15150 *18250 *18250
(–19') (33400) (33400) (40200) (40200)
PC800SE-7
Conditions: Boom: 7100 mm (23'4"), Bucket (SAE): 4.3 m3 (5.62 cu.yd), Shoes: 610 mm (24")
(Heavy-lifting: "OFF") unit: kg (lb)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2945 mm (9'8")
6.0 m *13250 11950 *13450 12800 *15250 *15250 *18500 *18500
(19') (29200) (26400) (29600) (28200) (33700) (33700) (40800) (40800)
3.0 m 13000 9950 *15200 11950 *18750 16700 *25000 24300
(9') (28600) (21900) (33500) (26300) (41300) (36800) (55100) (53500)
0m 13550 10300 14750 11250 20200 15450 *26850 22450 *27200 *27200
(0') (29800) (22700) (32500) (24800) (44600) (34100) (59200) (49500) (59900) (59900)
–3.0 m *15650 14250 *17200 15550 *22850 22750 *29600 *29600 *37150 *37150
(–9') (34500) (31400) (37900) (34300) (50300) (50200) (65300) (65300) (81900) (81900)
A MAX 9.0 m (29') 7.5 m (24') 6.0 m (19') 4.5 m (14') 3.0 m (9')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 2945 mm (9'8")
6.0 m *15300 11950 *15550 12800 *17500 *17500 *21050 *21050
(19') (33800) (26400) (34200) (28200) (38600) (38600) (46400) (46400)
3.0 m 13000 9950 15450 11950 *21450 16700 *28400 24300
(9') (28600) (21900) (34100) (26300) (47300) (36800) (62700) (53500)
0m 13550 10300 14750 11250 20200 15450 29750 22450 *30200 *30200
(0') (29800) (22700) (32500) (24800) (44600) (34100) (65600) (49500) (66600) (66600)
–3.0 m *18150 14250 *19850 15550 *26200 22750 *33850 *33850 *42600 *42600
(–9') (40000) (31400) (43800) (34300) (57800) (50200) (74700) (74700) (93900) (93900)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2C-84
AH_25.book Page 85 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC1250-7
Conditions: Boom: 9100 mm (29'10"), Bucket (SAE): 5.0 m3 (6.54 cu.yd), Shoes: 700 mm (28")
(Heavy-lifting: "OFF") unit: kg (Ib)
A MAX 12.2 m (40') 10.7 m (35') 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3400 mm (11'2")
9.1 m *15200 *15200 *15500 *15500
(30') (33500) (33500) (34200) (34200)
6.1 m *15850 12900 *17300 17100 *19950 *19950 *24400 *24400
(20') (34900) (28500) (38100) (37700) (44000) (44000) (53800) (53800)
3.0 m 15350 11600 16050 12200 *19800 15750 *23900 20500 *30550 27150
(10') (33800) (25600) (35400) (26900) (43700) (34800) (52700) (45200) (67400) (59800)
0.0 m 15950 12050 19600 14900 23750 17850 *32650 25600
(0') (35200) (26500) (43200) (32800) (52400) (39300) (72000) (56400)
–3.0 m *19600 14900 *19650 14950 *24750 19150 *30750 25800 *38350 37750 *39250 *39250
(–10') (43200) (32900) (43300) (33000) (54600) (42200) (67800) (56800) (84500) (83200) (86600) (86600)
–6.1 m *20150 *20150 *21900 *21900 *28150 *28150
(–20') (44500) (44500) (48200) (48200) (62100) (62100)
2C-85
AH_25.book Page 86 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC1250LC-7
Conditions: Boom: 9100 mm (29'10"), Bucket (SAE): 5.2 m3 (6.80 cu.yd), Shoes: 1000 mm (39")
(Heavy-lifting: "OFF") unit: kg (Ib)
A MAX 12.2 m (40') 10.7 m (35') 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3400 mm (11'2")
9.1 m *15200 *15200 *15500 *15500
(30') (33500) (33500) (34200) (34200)
6.1 m *15850 13850 *17300 *17300 *19950 *19950 *24400 *24400
(20') (34900) (30500) (38100) (38100) (44000) (44000) (53800) (53800)
3.0 m *16750 12500 *17150 13150 *19800 16850 *23900 21800 *30550 28850
(10') (36900) (27600) (37800) (29000) (43700) (37200) (52700) (48100) (67400) (63600)
0.0 m *18050 12950 *21250 15950 *24700 19150 *32650 27300
(0') (39800) (28600) (46900) (35200) (54400) (42200) (72000) (60100)
–3.0 m *19600 16000 *19650 16050 *24750 20450 *30750 27450 *38350 *38350 *39250 *39250
(–10') (43200) (35300) (43300) (35400) (54600) (45100) (67800) (60600) (84500) (84500) (86600) (86600)
–6.1 m *20150 *20150 *21900 *21900 *28150 *28150
(–20') (44500) (44500) (48200) (48200) (62100) (62100)
2C-86
AH_25.book Page 87 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC1800-6
Conditions: Boom: 8700 mm (28'7"), Bucket (SAE): 12.0 m3 (15.7 cu.yd), Shoes: 810 mm (32")
(Heavy-lifting: "OFF") unit: kg (Ib)
A MAX 10.7 m (35') 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 3900 mm (12'10")
6.1 m 19700* 19700* 26950* 26950* 31150* 31150*
(20') (43400)* (43400)* (59400)* (59400)* (69600)* (69600)*
3.0 m 23050* 19800 30350* 30350* 36950* 36950* 44100* 44100* 63950* 63950*
(10') (50800)* (43700) (66900) (66900)* (81500)* (81500)* (97300)* (97300)* (142100)* (142100)*
0.0 m 24050* 20450 31650* 28300 39150* 37050 49800* 49800* 65500* 65500* 35500* 35500*
(0') (53100)* (45100) (69800)* (62400)* (86400)* (81600) (110700)* (110700)* (145600)* (145600)* (78300)* (78300)*
–3.0 m 24900* 24900* 28050* 27650 35700* 35700* 45050* 45050* 57250* 57250* 67850* 67850* 50450* 50450*
(–10') (54900)* (54900)* (61800)* (60900)* (78700)* (78700)* (99300)* (99300)* (127200)* (127200)* (150800)* (150800)* (112100)* (112100)*
–6.1 m 23050* 23050* 29000* 29000* 37050* 37050* 45300* 45300*
(–20') (50800)* (50800)* (63900)* (63900)* (81700)* (81700)* (99900)* (99900)*
Conditions: Boom: 9100 mm (29'10"), Bucket (SAE): 10.0 m3 (13.1 cu.yd), Shoes: 810 mm (32")
(Heavy-lifting: "OFF") unit: kg (Ib)
A MAX 12.2 m (40') 10.7 m (35') 9.1 m (30') 7.6 m (25') 6.1 m (20') 4.6 m (15')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 4100 mm (13'5")
9.1 m *20000 *20000 25100* 25100*
(30') (44100)* (44100)* (55300)* (55300)*
6.1 m 21450* 21050* 27200* 26900 30650* 30650* 35550* 35550*
(20') (47300)* (46400)* (60000)* (59300) (67500)* (67500)* (78400)* (78400)*
3.0 m 24850* 19250 29850* 24950 34900* 31900 42100* 41650 53250* 53250*
(10') (54800)* (42500) (65800)* (55000) (76900)* (70700)* (92800)* (91800) (117420)* (117420)*
0.0 m 27000 19850 30900* 23350 37050* 29550 43350* 36150 56950* 51550 64150* 54150*
(0') (59500) (43700) (68200)* (51500) (81600)* (65200)* (95600)* (79700) (125570)* (113670) (141450)* (141450)*
–3.0 m 28250* 23650 34650* 28800 41000* 35250 53100* 50600 66950* 66950* 64000* 64000*
(–10') (52300)* (52100) (76400)* (63500) (90400)* (77800) (117080)* (111570) (147620)* (147620)* (141120)* (141120)*
–6.1 m 27850* 27850* 30400* 30400* 36250* 36250* 48800* 48800* 60150* 60150*
(–20') (61400)* (61400)* (67000)* (67000)* (79900)* (79900)* (107600)* (107600)* (132630)* (132630)*
2C-87
AH_25.book Page 88 Tuesday, March 23, 2004 9:41 AM
LIFTING CAPACITY
PC1800-6
Conditions: Boom: 11400 mm (37'5"), Bucket (SAE): 5.6 m3 (7.3 cu.yd), Shoes: 810 mm (32")
(Heavy-lifting: "OFF") unit: kg (Ib)
A MAX 15.2 m (50') 12.2 m (40') 9.1 m (30') 6.1 m (20') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 5000 mm (16'5")
12.2 m 13150* 13150*
(40') (29000)* (29000)*
9.1 m 13000* 13000* 13350* 13350*
(30') (28600)* (28600)* (29400)* (29400)*
6.1 m 13300* 12250 14600* 14600* 18550* 18550* 26550* 26500*
(20') (29300)* (27000) (32100)* (32100)* (40900)* (40900)* (58500)* (58500)*
3.0 m 13900* 11150 16050* 15000 21500* 21500* 32350* 32350*
(10') (30600)* (24600) (35400)* (33100)* (47400)* (47400)* (71300)* (71300)*
0.0 m 14750* 11150 17100* 13800 23600* 21150 35500* 33850
(0') (32500)* (24600) (37700)* (30400)* (52000)* (46600)* (78200)* (74700)
–3.0 m 15750* 12450 16900* 13300 24100* 20000 35600* 32600 33850* 33850*
(–10') (34800)* (27500) (37300)* (29300) (53100)* (44100) (78500)* (71900) (74700)* (74700)*
–6.1 m 16750* 16000 22000* 20200 32500* 32500* 49350* 49350* 38500* 38500*
(–20') (36900)* (35200) (48500)* (44500) (71600)* (71600)* (108800)* (108800)* (84800)* (84800)*
–9.1 m 16700* 16700* 23950* 23950* 36000* 36000*
(–30') (36800)* (36800)* (52800)* (52800)* (79400)* (79400)*
2C-88
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2D
BACKHOE ATTACHMENTS
CONTENTS
Buckets & rippers for backhoe
Ripper bucket ....................................................... 2D-2
Trapezoidal bucket .............................................. 2D-2
Slope finishing bucket ........................................ 2D-2
Ditch cleaning bucket ......................................... 2D-2
Single-shank rippers ........................................... 2D-2
Three-shank rippers ............................................ 2D-3
Clamshell bucket ................................................. 2D-3
Coal bucket and chip bucket .............................. 2D-3
Chip yard bucket ................................................. 2D-3
2D-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Ripper Bucket
Suitable for digging rock bed or hard clayey soil
when normal buckets cannot penetrate deep
enough. Loading is also possible.
Trapezoidal Bucket
Performs digging and sloping simultaneously on a
drainage or irrigation canal. Using this bucket will
leave the digging profile shaped as a cross-section.
Single-shank Ripper
This ripper is used for site preparation prior to
digging work, when it becomes necessary to remove
rocks, pavement for other obstacles. Also effective
for pulling out tree stumps.
2D-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Three-shank Ripper
This ripper is an efficient tool for digging up rocks on
a slope, digging, crushing and ripping of concrete
surfaces, and pulling out tree stumps.
Clamshell Bucket
• Improved work efficiency with the clamshell
bucket pushing method.
• Handy 360-degree manual rotation
• Superb earth digging and discharge performance
2D-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
2D-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
• 2-piece boom
The 2-piece boom can be installed singly for
wider working range.
• Rotary arm
The excavator, of which can be rotated 360
degrees, can be widely applied to miscellaneous
works.
WORKING RANGE
CORNER SHOVEL SPECS (EQUIPPED WITH 2-PIECE BOOMS & ROTARY ARM)
MODEL PC60-7B PC120 PC200 PC78US
OPERATING WEIGHT (kg) 8400 12900 19800 8820
FLYWHEEL HORSEPOWER (kW(PS)/rpm) 40.5(55)/2100 64(87)/2200 99.3(135)/2000 40.5(55)/2100
STANDARD BUCKET CAPACITY (M3) 0.28 0.35 0.6 0.28
ROTARY ARM SWING SPEED (rpm) 8.0 8.0 7.0 10.0
WORKING RANGE
A MAX.DIGGING HEIGHT (mm) 8315 8475 9810 9025
B MAX.DUMPING HEIGHT (mm) 6185 6095 6965 6945
C MAX.DIGGING DEPTH (mm) 4655 5245 6395 4445
D MAX.DIGGING REACH (mm) 7675 8180 10000 7945
E MIN.SWING RADIUS (mm) 2515 2780 3530 2500
F TAIL SWING RADIUS (mm) 1850 2130 2750 1430
DIMENSION
LENGTH x HEIGHT x WIDTH (mm) 5790x2645x2280 7460x2780x2490 9260x2905x2800 6445x2770x2365
PC60-7B & PC78US : WHEN BLADE IS INSTALLED.
BUCKET CAPACITY : WHEN CONFORMED TO FORMER JIS, STD BUCKET CAPACITY CHANGES AS INDICATED IN [ ].
2D-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Offset Boom
• Unique parallelogram type offset boom for
perfectly vertical excavation of side ditches.
• Bucket offset parallels the direction the machine
is moving.
• Precise excavation close to any structure is no
longer a problem.
• A single touch precisely offsets the bucket.
NOTE: Single linkage type by other manufacturer is
also available.
Spike Hammer
This hammer is suitable for chipping concrete
structures such as tunnels, slopes of dams,
breakwaters, etc. when they are repaired and
constructed. It can chip the concrete surfaces
powerfully.
2D-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Road Ripper
• As the ripper is light, pitching can be restrained
when stripping roadbed.
• To improve penetration into the roadbed, the road
ripper tip is thinner than conventional ones
• To facilitate stripping work, the tip bottom is linear
in shape.
• To increase digging force, the distance between
the arm top pin and the tooth tip is short.
Crushing force
55 ton~100 ton (PC120 class)
65 ton~110 ton (PC200 class)
2D-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Hydraulic Breaker
• The KOMATSU hydraulic breaker design
incorporates only two internal moving parts, Mini range
offering reliability and long life.
• Each breaker has a wide range of oil flow
allowing for mounting of the same breaker on a
wide range of equipment, suiting a variety of
applications such as Constructions, Demolition,
Recycling, Mining and Quarrying.
• With breakers available in 15 models from 73 kg
to 4000 kg class, you can be assured of finding
just the right capabilities. JTHB08 JTHB10 JTHB20 JTHB30 JTHB40 JTHB50
Breaker model Base machine
JTHB08 PC09, PC10MR
JTHB10 PC15MR Medium range
JTHB20 PC20MR
JTHB30 PC27MR, PC30MR
JTHB40 PC35MR
JTHB50 PC40MR, PC45MR
JTHB60 PC60, PC78US, WB70A
WB91R–WB98A, WB140PS,
JTHB65
WB150PS
JTHB70 PC100–PC138US
JTHB100 PC160LC
JTHB150 PC200–PC228US
JTHB190 PC220–PC230
JTHB60 JTHB65 JTHB70 JTHB100 JTHB150
JTHB230 PC300–PC350
JTHB310 PC400, PC450
JTHB400 PC600 Large range
2D-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
2D-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Lifting Magnet
• Lifting magnet with strong attraction force by
over-excitation and swift release by reverse
excitation.
• Engine-driven brushless alternator, realizing a
maintenance free operation.
• Comfortable cab of minimum vibration, which
makes an operator least tired even with long
hours of operation.
• A variety of cabs now available.
(A parallel link cab and high mount cab are
prepared as an option)
PC200LC
Wide shoe: option
2D-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Optional Equipment
GRAPPLES Prallel Link Cab High Mount Cab
SCRAP
GRAPPLE
ORANGE
GRAPPLE
2D-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
2D-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
BACKHOE
ATTACHMENTS
Scrap Grapple
To assure safe handling of massive or irregularly
shaped scrap, each of the 4 claws opens and closes
by independent hydraulic cylinders. The grapple
rotates freely to make grappling readjustments safe
and easy.
Orange Grapple
The claws are 4 vane-shaped blades operated
independently by hydraulic cylinders. The freely
turn-able grapple surrounds the scrap material;
grasps accurately, and keeps small-item spillage to
a minimum.
Magnet Fork
An excavator-based machine with a lifting magnet
and fork device exhibits the best operating
performance in scrap handlings by itself through the
combination of both the MAGNET absorbing and
FORK grapple forces, thus enabling great
improvement of working efficiency, because
materials to be handled can be freely selected.
SPECIFICATIONS
Model PC200LC PC220LC
Operating weight kg/lb 23660 (52160) 28140 (62040)
Magnet outer diameter mm/ft.in Ø1120 (3'8") Ø1320 (4'4")
Alternator output kW 10 15
2D-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2E
HYDRAULIC
LOADING SHOVELS
CONTENTS
Features .................................................................... 2E-2
Specifications ........................................................... 2E-4
Dimensions ............................................................... 2E-6
Working ranges, Digging Force .............................. 2E-7
Component dimensions and weight ...................... 2E-8
Ground pressure .................................................... 2E-17
Loading shovel buckets ........................................ 2E-18
Model selection ...................................................... 2E-19
Production .............................................................. 2E-20
2E-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features HYDRAULIC
LOADING SHOVELS
2E-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Features HYDRAULIC
LOADING SHOVELS
Komatsu hydraulic system HYDRO-PILOT
• Multi-circuit hydraulic system with electronic load governor, pump flow summation capability, and oil flow
priority based on demand, for fast working cycles and high productivity
• All main hydraulic circuits are run at one pressure level only, simplifying pressure adjustment and service
• Each circuit with connection facility for pressure check gauges
• Changing from front shovel to backhoe is simple
• Un-pressurised hydraulic tank with large pump suction lines and low pump speed prevents risk of
cavitation
• Each hydralulic circuit protected with high pressure filters
• Full flow 10 µm return line filters for system safety and for supplementary circuits 3 µm by-pass filter to
improve oil quality for long component lifetime
• Swing out hydraulic cooler for simple cleaning to keep the cooling efficiency
• Float valves for improved hydraulic system
Heavy-duty shovel undercarriage design
• Komatsu Mining track system with oscillating shoes for optimum response to rugged mining ground
conditions
• Lifetime lubricated rollers
• Automatic track tensioning system
• Track shoes in high quality casting steel and engineered by finite element method
• Precision hard facing of contact surfaces for long term performance
• Different width of shoes available for best performance in softer mining ground conditions
Attachments
• Front shovel attachment available for all mining applications
• Closed box design combining steel plates and castings, engineered by finite element method for full
lifetime
• Wide selection of buckets and customised options
• Bucket wear package ranges to meet all mining conditions
• Attachment pin sealing arrangement for reduced bearing wear-parts costs
Service
• Hydraulically assisted ladder for ease and convenience access
• Upper structure walkway allows safe access to all service points
• Walk in machinery house provides all weather protection for service attention
• Automatic central lubrication system for attachment and main swing bearing
• Swing down service arm for fast, ground level refilling and evacuation and the minimizing of leakages
during service
• Complete machine delivered in pre-tested modules for fast erection on job site
2E-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Specifications HYDRAULIC
LOADING SHOVELS
2E-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Specifications HYDRAULIC
LOADING SHOVELS
2E-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Dimensions HYDRAULIC
LOADING SHOVELS
L E
D
M
K F
C
G
I
A
H
B J
FVBH0104
A B C D E F G H I J K L M
mm mm mm mm mm mm mm mm mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
555 2740 3340
PC400-7 (1'10") (9') (11')
4020 5025 1320 3605 2995 3265 600 3490 2715 8455 4400
(13'2") (16'6") (4'4") (11'10") (9'10") (10'9") 685 2890 (24") (11'5") (8'11") (27'9") (14'5")
PC400-7***
(2'3") (9'6") 2990**
(9'10")
PC400LC-7 555 2740 3440
(1'10") (9') (11'3")
4350 5355 1320 3605 2995 3265 700 3490 2715 8455 4400
(14'3") (17'7") (4'4") (11'10") (9'10") (10'9") 685 2890 (28") (11'5") (8'11") (27'9") (14'5")
PC400LC-7***
(2'3") (9'6") 2990**
(9'10")
4250 5370
PC600-7
(13'11") (17'7") 1370 3675 3195 3295 790 3300 600 3900 3075 8815 5540
(4'6") (12'1") (10'6") (10'10") (2'7") (10'10") (24") (12'10") (10'1") (28'11") (18'2")
PC600LC-7 4600 5690
(15'1") (18'8")
3500 4110
4500 5810 1560 4245 3195 3560 840 (11'6") 610 (13'6") 3445 9865 5640
PC750-7 (14'9") (19'1") (5'1") (13'11") (10'6") (11'8") (2'9") (24")
2780** 3390** (11'4") (32'4") (18'6")
(9'1") (11'1")
4995 6425 1790 4810 3470 4120 990 3900 700 4600 3925 10940 6200
PC1250-7
(16'5") (21'1") (5'10") (15'9") (11'5") (13'6") (3'3") (12'10") (28") (15'1") (12'11") (35'11") (20'4")
5780 7445 2080 6140 5055 6510 730 4600 810 5410 4535 13230 8180
PC1800-6
(19') (24'5") (6'10") (20'2") (16'7") (21'4") (2'5") (15'1") (32") (17'9") (14'11") (43'5") (26'10")
** When retracted
*** Variable gauge
N L
E D
F M K
C
G
I
H A
J B
FVBH0108
A B C D E F G H I J K L M N
mm mm mm mm mm mm mm mm mm mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
4870 6405 1900 4805 4795 6246 777 4250 600 5050 3900 11000 6700 5750
PC1400-1 (16') (21') (6'3") (15'9") (15'9") (20'6") (2'7") (13'11") (24") (16'7") (12'10") (36'1") (22') (18'10")
PC3000-1 6000 7905 2710 5950 5910 7930 908 4800 800 5600 5280 13500 7930 6290
(19'8") (25'11") (8'11") (19'6") (19'5") (26'0") (3') (15'9") (31'5") (18'4") (17'4") (44'4") (26'6") (20'8")
PC4000-6 6245 8375 2942 6090 7067 8260 980 5350 1200 6550 6027 14100 9000 7650
(20'6") (27'6") (9'8") (20') (23'2") (27'1") (3'3") (17'7") (47") (21'6") (19'9") (46'3") (29'6") (25'1")
6800 9100 3240 7260 7270 8535 970 5800 1350 7150 6342 16370 10000 8000
PC5500-6 (22'4") (29'10") (10'8") (23'10") (23'10") (28'0") (3'2") (19') (53") (23'6") (20'10") (53'9") (32'10") (26'3")
6800 9100 3240 7165 6600 8745 970 5800 1350 7150 6342 18200 10500 9400
PC8000-6 (22'4") (29'10") (10'8") (23'6") (21'8") (28'8") (3'2") (19') (53") (23'6") (20'10") (59'9") (34'5") (30'10")
2E-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
G
Boom le
ngth
A
th
ng B
le
m
Ar
F
C
E
D FVBH0105
A
B
C F
E
D
FVBH0109
2E-7
02E.fm Page 8 Friday, March 26, 2004 1:27 PM
Four-part structure
(1) Work equipment ass’y (L/S) 16.2t (35,710 lb)
Width 2090 (6'10")
2830 (9'3")
8580 (28'2")
Three-part strucure
(1)
(3) Undercarriage Work equipment ass’y
PC600-7 16.4t (36,160 lb)
PC600LC-7 17.4t (38,360 lb)
(5) Base machine
875 (2'11") PC600-7 33.9t (74,740 lb)
PC600LC-7 35.0t (77,160 lb)
(4'2")
1260
(4)
3") 50 7 ") 50
(6' 0( (7' 0(
1'8 Other
10 1'8 10
19 ") 23 ")
2E-8
02E.fm Page 9 Friday, March 26, 2004 1:27 PM
Four-part structure
(1) Work equipment ass’y (L/S) 18.7t (41,230 lb)
5 (9'4")
2885
9500
0 (31'2")
Three-part strucure
(1)
(3) Undercarriage 20.7t (45,640 lb)
1305 Work equipment ass'y
(4'3")
(4'9")
5810 (19'1")
(*3730 (12'3"))
3620 (11'11")
(4) Other 10.0t (22,050 lb)
319
5 (1
830 ") 0'6
")
9
(2' 6840 (22'5")
(1'7")
470
(6'0")
1530
(4)
(3'7")
1090
2E-9
02E.fm Page 10 Friday, March 26, 2004 1:27 PM
(1) Work equipment assembly 27.5t (30.3 U.S. ton) (3) Undercarriage 30.0t (33.1 U.S. ton)
1585(5'2")
7.1t 5650x1500x2000
(7.8USt) (18'6")x(4'11")x(6'7") FVBH0190
Arm
Weight
5.1t 4100x1300x1200 PC1250:30.0t (33.1USt)
(5.6USt) (13'5")x(4'3")x(3'11") FVBH0191 15.0t x2(16.5 x2USt) FVBH0195
Bucket Boom cylinder
2.6t (2.87USt)
1.3t x2 (1.43USt x2) (4) Other 27.7t (30.5 U.S. ton)
9.9t (10.9USt)
3010x2710x2900 3520(11'7")
(9'11")x(8'11")x(9'6") FVBH0192 2850(9'4")
FVBH0193
845 620
(2'9") (2')
(2) Upper structure 23.9t (26.3 U.S. ton) 3155(10'4")
1810
6420(21'1") (5'11")
1760(5'9")
100(3.9")
2510(8'3")
880(2'11")
3470(11'5")
1830
(6')
Width:3490 (11'9")
Weight:23.9t (26.3USt) FVBH0178 18.0t(19.8USt) FVBH0180
2E-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
3 Bucket
3350 3220 3250 14400
(11'0") (10'7") (10'8") (31,750)
4 Cylinders
Boom cylinders 4180 — — 2330 × 2
(5,140 × 2)
(13'9")
6 Center frame
3330 3770 2100 18000
(10'11") (12'4") (6'11") (39,680)
7 Undercarriage
7440 1930 1890 25500
(24'5") (6'4") (6'2") (56,220)
8 Undercarriage
7440 1930 1890 25500
(24'5") (6'4") (6'2") (56,220)
9 Operator cab
2100 1600 2080 850
(6'11") (5'3") (6'10") (1,874)
10 Counterweight
4910 710 2265 21300
(16'1") (2'4") (7'5") (46,960)
11 Other
7000
— — —
(15,430)
2E-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
2E-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
2E-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
2E-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
2E-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
2E-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
NOTE: The shoe for the long-track excavator (L and LC), wide shoe (excluding the narrowest shoe for a
model) and swamp shoe are provided with low ground pressure. These shoes should be used on
soft and swampy terrain where the standard excavator with standard shoe is not usable due to
sinking of the tracks. If such shoes are used in swampy fields with stones, stumps and roots,
bending of the shoe plates, cracks in the links, breakage of pins, loosening of shoe bolts and other
damage may result. Therefore, the job site must be studied carefully, to provide the customer with
correct instructions and advice.
2E-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
2E-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
2E-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
Production HYDRAULIC
LOADING SHOVELS
Estimated Hourly Production
ESTIMATED
BUCKET SIZE** (m3) OR (cu.yd)
CYCLE TIME
SEC. MIN. 2.5 2.8 3.1 3.4 3.7 4.0 4.3 4.6 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5
15.0 0.25 600 672 744 816 888 960 1032 1104 1200 1320 1440 1560 1680 1800 1920 2040
18.0 0.30 500 560 620 680 740 800 860 920 1000 1100 1200 1300 1400 1500 1600 1700
21.0 0.35 429 480 531 583 634 686 737 789 857 943 1029 1114 1200 1286 1371 1457
24.0 0.40 375 420 465 510 555 600 645 690 750 825 900 975 1050 1125 1200 1275
27.0 0.45 333 373 413 453 493 533 573 613 667 733 800 867 933 1000 1067 1133
30.0 0.50 300 336 372 408 444 480 516 552 600 660 720 780 840 900 960 1020
33.0 0.55 273 305 338 371 404 436 469 502 545 600 655 709 764 818 873 927
36.0 0.60 250 280 310 340 370 400 430 460 500 550 600 650 700 750 800 850
ESTIMATED
BUCKET SIZE** (m3) OR (cu.yd)
CYCLE TIME
SEC. MIN. 9.0 9.5 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 20 22 25 28 35 38
15.0 0.25 2160 2280 2400 2640 2880 3120 3360 3600 3840 4080
18.0 0.30 1800 1900 2000 2200 2400 2600 2800 3000 3200 3400
21.0 0.35 1543 1629 1714 1886 2057 2229 2400 2571 2743 2914 3428 3771 4285 4800 6000 6514
24.0 0.40 1350 1425 1500 1650 1800 1950 2100 2250 2400 2550 3000 3300 3750 4200 5250 5700
27.0 0.45 1200 1267 1333 1467 1600 1733 1867 2000 2133 2267 2666 2933 3333 3733 4666 5066
30.0 0.50 1080 1140 1200 1320 1440 1560 1680 1800 1920 2040 2400 2640 3000 3360 4200 4560
33.0 0.55 982 1036 1091 1200 1309 1418 1527 1636 1745 1855 2181 2400 2727 3054 3818 4145
36.0 0.60 900 950 1000 1100 1200 1300 1400 1500 1600 1700 2000 2200 2500 2800 3500 3800
Actual production = (Estimated Hourly production) × (Bucket fill factor) × (Job efficiency)
Bucket Fill Factor (K) (PC400~PC1800) Job Efficiency(E)
Loading conditions K
Easy loading 1.0
Average loading 0.95
Severe loading 0.90
*4 : KMG Mining Shovels (Loading shovel)
2E-20
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2F
WHEEL-TYPE
EXCAVATORS
CONTENTS
Features .....................................................................2F-2
Specifications ............................................................2F-3
Dimensions ................................................................2F-6
Working ranges, digging force ................................2F-8
Bucket and arm combinations ...............................2F-10
Lifting capacity ........................................................2F-12
2F-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features WHEEL-TYPE
EXCAVATORS
High mobility
• A high-power KOMATSU engine gives it a higher travel speed for quick relocation.
• Four-wheel drive and double tires (PW75~PW220) both front and rear make it easy to travel over rough or
soft terrain.
High working performance
• Large working range and strong digging force.
• The PC system makes full use of engine power. (PW75~PW220)
• A two-pump merge system increases work equipment speed and reduces cycle time.
• Smooth, responsive swing starts and stops.
• High lifting capacity and good stability.
High operating versatility
• Extra-small swing radius boosts operating versatility.
• Excellent stability due to oscillation lock cylinders and double tires.
Enhanced operator comfort
• Hydrostatic drive system assures smooth, easy travel speed changes.
• Newly designed cab offers greater comfort.
Excellent safety and easy maintenance
• Four wheel disc brake with positive braking
• One of the features now on the new wheeled excavator is a walkway across the excavator superstructure,
giving easy access to the engine compartment.
(PW200-7, PW220-7)
In harmony with the environment
• Low emission engine
The powerful turbocharged and air-to-air aftercooled Komatsu SAA6D102E-2 provides 118 kW/158 HP.
This engine meets Stage II emissions standards with increased power and machine productivity.
• Economy mode reduces fuel consumption
• Low operating noise
• Designed for easy end of life recycling
(PW200-7, PW220-7)
Undercarriage
• Designed for high ground clearance
• High oscillation angle
• Virtually zero axle rocking with outboard wet disc system
• Powerful drawbar pull
• Automatic 3-speed travel
• Class leading 35 km/h maximum travel speed
(PW200-7, PW220-7)
SpaceCabTM
The new PW200/220-7'scabin space have been increased by 14%, offering an exceptionally-roomy
operating environment.
• High-pressurised cabin with optional air conditioner
• Low-noise design
• Low-vibration design with cabin damper mounting
• Cab moved forward for better visibility
• Ergonomic control levers
• Seat specially designed for wheeled machines, with exceptional extra comfort.
(PW200-7, PW220-7)
2F-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Specifications WHEEL-TYPE
EXCAVATORS
2F-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Specifications WHEEL-TYPE
EXCAVATORS
2F-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Specifications WHEEL-TYPE
EXCAVATORS
2F-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Dimensions WHEEL-TYPE
EXCAVATORS
L
D
J
F
K
C
G G.L
H B
I A FVBH0005
E
A B C D E F G H I J K L Boom Arm
mm mm mm mm mm mm mm mm mm mm mm mm length length
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) m (ft.in) m (ft.in)
2060 930 1040 1475 2000 2690 340 1684 2155 5720 1.7
PW75R-2** (6'9'') (3'1'') (3'5'') (4'10'') (6'7'') (8'10'') (1'1'') (5'6'') (7'1'') (18'9'') (5'7'')
PW95R-2** 2200 1000 1100 1510 2120 3020 405 1815 2315 5895 1.6
(7'3'') (3'3'') (3'7'') (4'11'') (6'11'') (9'11'') (1'4'') (5'11'') (7'7'') (19'4'') (5'3'')
3645 6935 2.06
2600 1000 1215 2020 2445 3020 320 1840 2420 (12') 2165 (22'9'') 4.26 (6'9'')
PW100-3 (8'6'') (3'3'') (4') (6'8'') (8') (9'11'') (1'1'') (6') (7'11'') (7'1'') (14'')
3750 6810 2.36
2400 1100 1175 1577 2120 3090 350 1945 2500 6540 1.85
PW110R-1** (7'10'') (3'7'') (3'10'') (5'2'') (6'11'') (10'2'') (1'2'') (6'5'') (8'2'') (21'5'') (6'1'')
3055 7590 2.1
2600 1000 1210 2112 2435 3043 340 1884 2500 (10') 2330 (24'11'') 4.6 (6'11'')
PW130ES-6*
(8'6'') (3'3'') (4') (6'11'') (8') (10') (1'1'') (6'2'') (8'2'') 3455 (7'8'') 7445 (15'1'') 2.5
(11'4'') (24'5'') (8'2'')
3945 5731 2.1
2600 1000 1210 2112 2435 3043 340 1884 2500 (12'11'') 2330 (18'10'') 4.8 (6'11'')
PW130ES-6**
(8'6'') (3'3'') (4') (6'11'') (8') (10') (1'1'') (6'2'') (8'2'') 3940 (7'8'') 5715 (15'9'') 2.5
(12'11'') (18'9'') (8'2'')
3163 7772 2.1
(19'7'') (25'6'') (6'11'')
2600 1000 1275 2292 2435 3069 340 1884 2500 3294 2410 7743 4.6 2.5
PW150ES-6* (8'6'') (3'3'') (4'2'') (7'6'') (8') (10'1'') (1'1'') (6'2'') (8'2'') (10'10'') (7'11'') (25'5'') (15'1'') (8'2'')
3867 7451 3.0
(12'8'') (24'5'') (9'10'')
3965 5973 2.1
(13') (19'7'') (6'11'')
2600 1000 1275 2292 2435 3069 340 1884 2500 3979 2410 5969 4.8 2.5
PW150ES-6** (8'6'') (3'3'') (4'2'') (7'6'') (8') (10'1'') (1'1'') (6'2'') (8'2'') (13'1'') (7'11'') (19'7'') (15'9'') (8'2'')
3954 5979 3.0
(13') (19'7'') (9'10'')
3374 8624 1.8
(11'1'') (28'4'') (5'11'')
2600 1000 1275 2417 2462 3134 340 1884 2500 3312 2410 8572 5.2 2.25
PW170ES-6*
(8'6'') (3'3'') (4'2'') (7'11'') (8'1'') (10'3'') (1'1'') (6'2'') (8'2'') (10'10'') (7'11'') (28'1'') (17'1'') (7'5'')
3141 8563 2.6
(10'4'') (28'1'') (8'6'')
3995 5827 1.8
(13'1'') (19'1'') (5'11'')
2600 1000 1275 2417 2462 3134 340 1884 2500 3995 2410 6550 5.2 2.25
PW170ES-6**
(8'6'') (3'3'') (4'2'') (7'11'') (8'1'') (10'3'') (1'1'') (6'2'') (8'2'') (13'1'') (711'') (21'6'') (17'1'') (7'5'')
3960 6960 2.6
(13'10'') (22') (8'6'')
3906 9479 1.8
(12'10") (31'1") (5'11")
3895 9435 2.4
2750 1450 1327 2700 2541 3234 330 1914 2541 (12'9") 2342 (30'11") 5.7 (7'10")
PW200-7*
(9'0") (4'9") (4'4") (8'10") (8'4") (10'7") (1'1") (6'3") (8'4") 3912 (7'8") 9427 (18'8") 2.9
(12'10") (30'11") (9'6")
3985 9467 3.5
(13'1") (31'1") (11'6")
2F-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Dimensions WHEEL-TYPE
EXCAVATORS
L
D
J
F
K
C
G G.L
H B
I A FVBH0005
E
A B C D E F G H I J K L Boom Arm
mm mm mm mm mm mm mm mm mm mm mm mm length length
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) m (ft.in) m (ft.in)
3980 7070 1.8
(13'1") (23'2") (5'11")
3980 7078 2.4
2750 1450 1327 2700 2541 3234 330 1914 2541 (13'1") 2342 (23'3") 5.4 (7'10")
PW200-7**
(9'0") (4'9") (4'4") (8'10") (8'4") (10'7") (1'1") (6'3") (8'4") 3997 (7'8") 7000 (17'9") 2.9
(13'1") (23'0") (9'6")
4505 7218 3.5
(14'9") (23'8") (11'6")
9480 2.41
2800 1420 1310 2680 2610 3130 335 1860 2490 3740 2520 (31'1'') 5.7 (7'11'')
PW210-1
(9'2'') (4'8'') (4'4'') (8'10'') (8'7'') (10'3'') (1'1'') (6'1'') (8'2'') (12'3'') (8'3'') 9460 (18'8'') 2.925
(31') (9'7'')
3920 9479 1.8
(12'10") (31'1") (5'11")
3909 9435 2.4
2750 1450 1341 2700 2785 3248 345 2124 2785 (12'10") 2356 (30'11") 5.7 (7'10")
PW220-7*
(9'0") (4'9") (4'5") (8'10") (9'2") (10'8") (1'2") (7'0") (9'2") 3926 (7'9") 9427 (18'8") 2.9
(12'11") (30'11") (9'6")
3999 9467 3.5
(13'1") (31'1") (11'6")
3995 7070 1.8
(13'1") (23'2") (5'11")
3995 7078 2.4
2750 1450 1341 2700 2785 3248 345 2124 2785 (13'1") 2356 (23'3") 5.4 (7'10")
PW220-7** (9'0") (4'9") (4'5") (8'10") (9'2") (10'8") (1'2") (7'0") (9'2") (7'9") (17'9")
4011 7000 2.9
(13'2") (23'0") (9'6")
4519 7218 3.5
(14'10") (23'8") (11'6")
2F-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
A
B
FVBH0006
* One piece boom *** Two piece boom & rotary arm
** Two piece boom *4 Using power max function
2F-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
A
B
FVBH0006
2F-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
Material weight up to 1.8 t/m 3 (3000 lb/cu.yd) Material weight up to 1.5 t/m3 (2500 lb/cu.yd)
Material weight up to 1.2 t/m 3 (2000 lb/cu.yd) Not usable.
Bucket capacity (heaped) Width Weight
SAE,PCSA CECE Without Side With Side kg (lb) Arm length
3
m (cu.yd) 3
m (cu.yd) cutters cutters (With side m (ft.in)
mm (in) mm (in) cutters)
PW75R-2** 1.7 (5'7") 2.1 (6'11")
0.086 (0.11) — 300 (11.8") — *128 (282) —
0.128 (0.17) — 400 (15.7") — *160 (353) —
0.171 (0.22) — 500 (19.7") — *184 (406) —
0.2 (0.26) — 600 (23.6") — *174 (384) —
0.232 (0.30) — 700 (27.6") — *189 (417) —
0.265 (0.35) — 800 (31.5") — *196 (432) —
PW95R-2** 1.6 (5'3") 1.85 (6'1")
0.086 (0.11) — 300 (11.8") — *128 (282)
0.128 (0.17) — 400 (15.7") — *160 (353)
0.171 (0.22) — 500 (19.7") — *184 (406)
0.213 (0.28) — 600 (23.6") — *200 (441)
0.255 (0.33) — 700 (27.6") — *218 (481)
0.298 (0.39) — 800 (31.5") — *236 (520)
0.34 (0.44) — 900 (35.4) — *256 (564)
PW100-3 2.0 (6'7") 2.3 (7'7")
0.18 (0.24) 0.16 (0.21) 450 (17.7") 570 (22.4") 220 (485)
0.28 (0.37) 0.26 (0.34) 600 (23.6") 720 (28.3") 289 (637)
0.36 (0.47) 0.33 (0.43) 700 (27.6") 820 (32.3") 314 (692)
0.38 (0.50) 0.35 (0.46) 825 (32.5") 950 (37.4") 345 (761)
0.44 (0.58) 0.40 (0.52) 825 (32.5") 925 (36.4") 358 (789)
0.56 (0.73) 0.50 (0.65) 1000 (39.4") — *388 (855)
PW110R-1**
0.093 (0.12) — 300 (11.8") — 168 (370)
0.139 (0.18) — 400 (15.7") — 194 (428)
0.181 (0.24) — 500 (19.7") — 218 (481)
0.225 (0.29) — 600 (23.6") — 234 (516)
0.27 (0.35) — 700 (27.6") — 252 (556)
0.314 (0.41) — 800 (31.5") — 270 (595)
0.36 (0.47) — 900 (35.4") — 294 (648)
0.4 (0.52) — 1000 (39.4") — 320 (705)
PW130ES-6 2.1 (6'11") 2.5 (8'2") Rotating arm
0.20 (0.26) 0.19 (0.25) 400 (15.7") — *270 (595)
0.27 (0 35) 0.25 (0.33) 450 (17.7") — *300 (661)
0.41 (0.55) 0.37 (0.48) 600 (23.6") — *420 (926)
0.48 (0.63) 0.44 (0.58) 700 (27.6") — *445 (981)
0.55 (0.72) 0.50 (0.65) 800 (31.5") — *460 (1014)
0.62 (0.81) 0.57 (0.75) 900 (35.4") — *495 (1091)
0.69 (0.90) 0.63 (0.82) 1000 (39.4") — *530 (1168)
0.76 (0.99) 0.69 (0.90) 1100 (43.3") — *550 (1213)
0.83 (1.09) 0.76 (0.99) 1200 (47.2") — *575 (1168)
0.90 (1.18) 0.82 (1.07) 1300 (51.2") — *605 (1334)
0.97 (1.27) 0.89 (1.16) 1400 (55.1") — *630 (1389)
1.14 (1.49) 1.04 (1.36) 1400 (55.1") — *675 (1488)
Rotating
PW150ES-6 2.1 (6'11") 2.5 (8'2") 3.0 (9'10")
arm
0.20 (0.26) 0.19 (0.25) 400 (15.7") — *270 (595)
0.27 (0 35) 0.25 (0.33) 450 (17.7") — *300 (661)
0.41 (0.55) 0.37 (0.48) 600 (23.6") — *420 (926)
0.48 (0.63) 0.44 (0.58) 700 (27.6") — *445 (981)
0.55 (0.72) 0.50 (0.65) 800 (31.5") — *460 (1014)
0.62 (0.81) 0.57 (0.75) 900 (35.4") — *495 (1091)
0.69 (0.90) 0.63 (0.82) 1000 (39.4") — *530 (1168)
0.76 (0.99) 0.69 (0.90) 1100 (43.3") — *550 (1213)
0.83 (1.09) 0.76 (0.99) 1200 (47.2") — *575 (1168)
0.90 (1.18) 0.82 (1.07) 1300 (51.2") — *605 (1334)
0.97 (1.27) 0.89 (1.16) 1400 (55.1") — *630 (1389)
1.14 (1.49) 1.04 (1.36) 1400 (55.1") — *675 (1488)
2F-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
These charts are based on over-side stability with fully loaded bucket at maximum reach.
Material weight up to 1.8 t/m3 (3000 lb/cu.yd) Material weight up to 1.5 t/m3 (2500 lb/cu.yd)
Material weight up to 1.2 t/m3 (2000 lb/cu.yd) Not usable.
Bucket capacity (heaped) Width Weight
SAE,PCSA CECE Without Side With Side kg (lb) Arm length
3
m (cu.yd) 3
m (cu.yd) cutters cutters (With side m (ft.in)
mm (in) mm (in) cutters)
PW170ES-6 1.8 (5'11") 2.2 (7'3") 2.6 (8'6")
0.27 (0.35) 0.25 (0.33) 450 (17.7") — *300 (661)
0.41 (0.55) 0.37 (0.48) 600 (23.6") — *420 (926)
0.48 (0.63) 0.44 (0.58) 700 (27.6") — *445 (981)
0.55 (0.72) 0.50 (0.65) 800 (31.5") — *460 (1014)
0.62 (0.81) 0.57 (0.75) 900 (35.4") — *495 (1091)
0.69 (0.90) 0.63 (0.82) 1000 (39.4") — *530 (1168)
0.76 (0.99) 0.69 (0.90) 1100 (43.3") — *550 (1213)
0.83 (1.09) 0.76 (0.99) 1200 (47.2") — *575 (1168)
0.90 (1.18) 0.82 (1.07) 1300 (51.2") — *605 (1134)
0.97 (1.27) 0.89 (1.16) 1400 (55.1") — *630 (1389)
1.14 (1.49) 1.04 (1.36) 1400 (55.1") — *675 (1488)
PW200-7 1.8 (5'11") 2.4 (7'11") 2.9 (9'6") 3.5 (11'6")
0.48 (0.63) — 600 (23.6") *480 (1058)
0.55 (0.72) — 700 (27.6") *530 (1168)
0.63 (0.82) — 800 (31.5") *580 (1279)
0.71 (0.93) — 900 (35.4") *610 (1345
0.78 (1.02) — 1000 (39.4") *650 (1433)
0.86 (1.12) — 1100 (43.3") *700 (1543)
0.96 (1.26) — 1200 (47.2") *760 (1675)
1.03 (1.35) — 1300 (51.2") *810 (1786) —
1.11 (1.45) — 1400 (55.1") *870 (1918) —
1.19 (1.56) — 1500 (59.1") *930 (2050) — —
1.49 (1.95) — 1600 (63.0") *1100 (2425) — — — —
1.58 (2.07) — 1700 (66.9") *1500 (2535) — — — —
1.68 (2.20) — 1800 (70.9") *1200 (2646) — — — —
PW210-1 1.8 (5'11") 2.41 (7'11") 2.925 (9'7")
0.36 (0.47) 0.33 (0.43) 560 (22") 665 (26.2") 410 (904)
0.50 (0.65) 0.45 (0.59) 750 (29.5") 855 (33.7") 440 (970)
0.80 (1.05) 0.70 (0.92) 1045 (44.1") 1150 (45.3") 576 (1270)
0.93 (1.22) 0.80 (1.05) 1200 (47.2") 1305 (51.4") 590 (1301)
1.05 (1.37) 0.90 (1.12) 1330 (52.4") 1435 (56.5") 656 (1433)
1.17 (1.53) 1.00 (1.31) 1450 (57.1") — *660 (1455)
1.40 (1.83) 1.20 (1.57) 1680 (66.1") — *710 (1565)
PW220-7 1.8 (5'11") 2.4 (7'11") 2.9 (9'6") 3.5 (11'6")
0.48 (0.63) — 600 (23.6") *480 (1058)
0.55 (0.72) — 700 (27.6") *530 (1168)
0.63 (0.82) — 800 (31.5") *580 (1279)
0.71 (0.93) — 900 (35.4") *610 (1345
0.78 (1.02) — 1000 (39.4") *650 (1433)
0.86 (1.12) — 1100 (43.3") *700 (1543)
0.96 (1.26) — 1200 (47.2") *760 (1675)
1.03 (1.35) — 1300 (51.2") *810 (1786)
1.11 (1.45) — 1400 (55.1") *870 (1918)
1.19 (1.56) — 1500 (59.1") *930 (2050) —
1.49 (1.95) — 1600 (63.0") *1100 (2425) — — —
1.58 (2.07) — 1700 (66.9") *1500 (2535) — — —
1.68 (2.20) — 1800 (70.9") *1200 (2646) — — — —
* Without side cutters
2F-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
L
A : Reach from swing center
B : Bucket hook height
C : Lifting capacity
Cf : Rating over front
B Cs : Rating over side
MAX : Rating at maximum reach
L : Arm length
C
kg(lb) FVBH0027
Conditions:
Bucket (SAE) : 0.232 m3 (0.30 cu.yd), Tires : 7.50-20 unit : kg (lb)
A MAX 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs
Arm length 1700 mm (5'7") With blade and outrigger above ground
4.5 m 1050* 700
(15') (2300) (1550)
3.0 m 1150* 700 1200* 1000
(10') (2550) (1550) (2650) (2200)
1.5 m 1200* 650 1250* 950 2800* 2000
(5') (2650) (1450) (2750) (2100) (6150) (4400)
0m 1350* 600 1400* 900 2800* 2050
(0') (2950) (1300) (3100) (2000) (6150) (4500)
–1.5 m 1450* 700 1500* 850 2750* 1950
(–5') (3200) (1550) (3300) (1850) (6050) (4300)
Arm length 2100 mm (6'11") With blade and outrigger above ground
4.5 m 1000* 650
(15') (2200) (1450)
3.0 m 1100* 650 1150* 950
(10') (2400) (1450) (2550) (2100)
1.5 m 1150* 600 1200* 900 2800* 1950
(5') (2550) (1300) (2650) (2000) (6150) (4300)
0m 1300* 550 1350* 850 2750* 2000
(0') (2850) (1200) (2950) (1850) (6050) (4400)
–1.5 m 1400* 650 1450* 800 2700* 1900
(–5') (3100) (1450) (3200) (1750) (5950) (4200)
Arm length 1700 mm (5'7") With blade and outrigger on ground
4.5 m 1150* 750
(15') (2550) (1650)
3.0 m 1250* 750 1300* 1100
(10') (2750) (1650) (2850) (2400)
1.5 m 1300* 700 1350* 1050 2900* 2900*
(5') (2850) (1550) (2950) (2300) (6400) (6400)
0m 1450* 650 1500* 1000 2850* 2850*
(0') (3200) (1450) (3300) (2200) (6250) (6250)
–1.5 m 1550* 750 1600* 950 2800* 2800*
(–5') (3400) (1650) (3500) (2100) (6150) (6150)
Arm length 2100 mm (6'11") With blade and outrigger on ground
4.5 m 1100* 700
(15') (2400) (1550)
3.0 m 1200* 700 1250* 1050
(10') (2650) (1550) (2750) (2300)
1.5 m 1250* 650 1300* 1000 2850* 2850*
(5') (2750) (1450) (2850) (2200) (6250) (6250)
0m 1400* 600 1450* 950 2800* 2800*
(0') (3100) (1300) (3200) (2100) (6150) (6150)
–1.5 m 1500* 700 1550* 900 2750* 2750*
(–5') (3300) (1550) (3400) (2000) (6050) (6050)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard No.J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
Conditions:
Bucket (SAE): 0.232 m3 (0.30 cu.yd), Tires:7.50-20 unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 1700 mm (5'7") With blade and outrigger above ground
4.5 m 650 500 1100 1000
(15') (1450) (1100) (2400) (2200)
3.0 m 600 450 750 450 1100 950
(10') (1300) (1000) (1650) (1000) (2400) (2100)
1.5 m 550 400 700 450 1200 900
(5') (1200) (900) (1550) (1000) (2650) (2000)
0m 550 350 700 400 1200 850 2400* 1800
(0') (1200) (800) (1550) (900) (2650) (1850) (5300) (3950)
–1.5 m 650 500 1100 700 2500* 1500
(–5') (1450) (1100) (2400) (1550) (5500) (3300)
Arm length 2100 mm (6'11") With blade and outrigger above ground
4.5 m 600 450 1000 950
(15') (1300) (1000) (2200) (2100)
3.0 m 550 400 700 500 1000 900
(10') (1200) (900) (1550) (1100) (2200) (2000)
1.5 m 500 350 700 450 1100 850
(5') (1100) (750) (1550) (1000) (2400) (1850)
0m 500 300 650 350 1100 800 2300* 1750
(0') (1100) (650) (1450) (750) (2400) (1750) (5050) (3850)
–1.5 m 600 450 1000 650 2400* 1450
(–5') (1300) (1000) (2200) (1450) (5300) (3200)
Arm length 1700 mm (5'7") With blade and outrigger on ground
4.5 m 1100* 600 1200* 1050
(15') (2400) (1300) (2650) (2300)
3.0 m 1000* 550 1050* 600 1200* 1000
(10') (2200) (1200) (2300) (1300) (2650) (2200)
1.5 m 950* 450 1000* 600 1250* 950
(5') (2100) (1000) (2200) (1300) (2750) (2100)
0m 1050* 450 1100* 550 1250* 900 2500* 1900
(0') (2300) (1000) (2400) (1200) (2750) (2000) (5500) (4200)
–1.5 m 1150* 600 1150* 850 2600* 1600
(–5') (2550) (1300) (2550) (1850) (5700) (3500)
Arm length 2100 mm (6'11") With blade and outrigger on ground
4.5 m 1000* 550 1000* 600 1100* 1000
(15') (2200) (1200) (2200) (1300) (2400) (2200)
3.0 m 900* 500 1000* 550 1100* 950
(10') (2000) (1100) (2200) (1200) (2400) (2100)
1.5 m 850* 450 950* 500 1150* 900
(5') (1850) (1000) (2100) (1100) (2550) (2000)
0m 950* 400 1050* 450 1150* 850 2400* 1850
(0') (2100) (900) (2300) (1000) (2550) (1850) (5300) (4050)
–1.5 m 1050* 550 1100* 800 2500* 1550
(–5') (2300) (1200) (2400) (1750) (5500) (3400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2F-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
L
A : Reach from swing center
B : Bucket hook height
C : Lifting capacity
Cf : Rating over front
B
Cs : Rating over side
MAX : Rating at maximum reach
C L : Arm length
kg(lb) FVBH0027
2F-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
Conditions:
Bucket (SAE): 0.32 m3 (0.42 cu.yd), Tires: 9.00-20 unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 1850 mm (6'1") With blade and outrigger above ground
4.5 m 1000 900 2100 1900
(15') (2200) (2000) (4600) (4200)
3.0 m 800 700 950 700 1900* 1700
(10') (1750) (1550) (2100) (1550) (4200) (3750)
1.5 m 700 600 850 650 1550 1400 3900* 2600
(5') (1550) (1300) (1850) (1450) (3600) (3100) (8600) (5700)
0m 750 650 1400 1300 3750* 2400
(0') (1650) (1450) (3100) (2850) (8250) (5300)
–1.5 m 850 750 1650 1500 3500* 2400
(–5') (1850) (1650) (3650) (3300) (7700) (5300)
–3.0 m 1100 1000 3200* 2500
(–10') (2400) (2200) (7050) (5500)
Arm length 2000 mm (6'7") With blade and outrigger above ground
4.5 m 950 850 1000 900 2000 1800
(15') (2100) (1850) (2200) (2000) (4400) (3950)
3.0 m 850 650 900 800 1700 1550
(10') (1850) (1450) (2000) (1750) (3750) (3400)
1.5 m 750 550 800 700 1450 1300 3800* 2500
(5') (1650) (1200) (1750) (1550) (3200) (2850) (8350) (5500)
0m 700 600 800 700 1300 1250 3600* 2250
(0') (1550) (1300) (1750) (1550) (2850) (2750) (7900) (4950)
–1.5 m 800 700 1550 1400 3400* 2200
(–5') (1750) (1550) (3400) (3100) (7500) (4850)
–3.0 m 1050 950 1650 1500 3100* 2250
(–10') (2300) (2100) (3650) (3300) (6800) (4950)
Arm length 2300 mm (7'7") With blade and outrigger above ground
4.5 m 900 800 950 850 1900 1750
(15') (2000) (1750) (2100) (1850) (4200) (3850)
3.0 m 700 600 850 750 1650 1500
(10') (1550) (1300) (1850) (1650) (3650) (3300)
1.5 m 600 500 750 650 1350 1200 3750* 2400
(5') (1300) (1100) (1650) (1450) (2950) (2650) (8250) (5300)
0m 650 550 750 600 1250 1100 3500* 2100
(0') (1450) (1200) (1650) (1300) (2750) (2400) (7700) (4600)
–1.5 m 750 650 1450 1300 3300* 2000
(–5') (1650) (1450) (3200) (2850) (7250) (4400)
–3.0 m 1000 900 1550 1400 3000* 2050
(–10') (2200) (2000) (3400) (3100) (6600) (4500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2F-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
Conditions:
Bucket (SAE): 0.32 m3 (0.42 cu.yd), Tires: 9.00-20 unit:kg(lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 1850 mm (6'1") With blade and outrigger on ground
4.5 m 1100 1000 2400* 2000
(15') (2400) (2200) (5300) (4400)
3.0 m 900 800 1400* 800 2300* 1800
(10') (2000) (1750) (3100) (1750) (5050) (3950)
1.5 m 800 700 1200* 750 2250* 1500 3900* 3900*
(5') (1750) (1550) (2650) (1650) (4950) (3300) (8600) (8600)
0m 850 750 2100* 1400 3750* 3750*
(0') (1850) (1650) (4600) (3100) (8250) (8250)
–1.5 m 950 850 2200* 1600 3500* 3500*
(–5') (2100) (1850) (4850) (3500) (7700) (7700)
–3.0 m 1200 1100 3200* 3200*
(–10') (2650) (2400) (7050) (7050)
Arm length 2000 mm (6'7") With blade and outrigger on ground
4.5 m 1050 950 1500* 1000 2300* 1900
(15') (2300) (2100) (3300) (2200) (5050) (4200)
3.0 m 850 750 1250* 900 2200* 1900
(10') (1850) (1650) (2750) (2000) (4850) (4200)
1.5 m 750 650 1100* 800 2100* 1400 3800* 3800*
(5') (1650) (1450) (2400) (1750) (4600) (3100) (8350) (8350)
0m 800 700 1000* 850 2000* 1350 3600* 3600*
(0') (1750) (1550) (2200) (1850) (4400) (2950) (7900) (7900)
–1.5 m 900 800 2100* 1500 3400* 3400*
(–5') (2000) (1750) (4600) (3300) (7500) (7500)
–3.0 m 1100 1000 2250* 1600 3100* 3100*
(–10') (2400) (2200) (4950) (3500) (6800) (6800)
Arm length 2300 mm (7'7") With blade and outrigger on ground
4.5 m 1000 900 1400* 950 2200* 1850
(15') (2200) (2000) (3100) (2100) (4850) (4050)
3.0 m 800 700 1100* 850 2100* 1600
(10') (1750) (1550) (2400) (1850) (4600) (3500)
1.5 m 700 600 1000* 750 2000* 1300 3750* 3750*
(5') (1550) (1300) (2200) (1650) (4400) (2850) (8250) (8250)
0m 750 650 950* 700 1900* 1200 3500* 3500*
(0') (1650) (1450) (2100) (1550) (4200) (2650) (7700) (7700)
–1.5 m 850 750 2000* 1400 3300* 3300*
(–5') (1850) (1650) (4400) (3100) (7250) (7250)
–3.0 m 1100 1000 2150* 1500 3000* 3000*
(–10') (2400) (2200) (4750) (3300) (6600) (6600)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2F-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
Conditions:
Bucket (SAE): 0.32 m3 (0.42 cu.yd), Tires: 9.00-20 unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs
Arm length 1850 mm (6'1") With blade and outrigger above ground
4.5 m 900 800 900 800 2200 2000
(15') (2000) (1750) (2000) (1750) (4850) (4400)
3.0 m 750 650 800* 700 2000 1800
(10') (1650) (1450) (1750) (1550) (4400) (3950)
1.5 m 550 450 750* 650 1700 1500
(5') (1200) (1000) (1650) (1450) (3750) (3300)
0m 550 450 700 600 1500 1400
(0') (1200) (1000) (1550) (1300) (3300) (3100)
–1.5 m 700 550 850 750 1700 1600 3600* 3600*
(–5') (2550) (1200) (1850) (1650) (3750) (3500) (7900) (7900)
–3.0 m 900 800 1850 1700 3300* 3300*
(–10') (2000) (1750) (4050) (3750) (7250) (7250)
Arm length 2000 mm (6'7") With blade and outrigger above ground
4.5 m 850 750 900 800 2100 1900
(15') (1850) (1650) (2000) (1750) (4600) (4200)
3.0 m 700 600 800 700 1800 1650
(10') (1550) (1300) (1750) (1550) (3950) (3650)
1.5 m 500 400 750 650 1600 1400
(5') (1100) (900) (1650) (1450) (3500) (3100)
0m 550 400 700 600 1400 1350
(0') (1200) (900) (1550) (1300) (3100) (2950)
–1.5 m 550 450 750 700 1700 1500 3500* 3500*
(–5') (1200) (1000) (1650) (1550) (3750) (3300) (7700) (7700)
–3.0 m 850 750 1750 1600 3200* 3200*
(–10') (1850) (1650) (3850) (3500) (7050) (7050)
Arm length 1850 mm (6'1") With blade and outrigger above ground
4.5 m 1000 900 1750* 900 2500* 2100
(15') (2200) (2000) (3850) (2000) (5500) (4600)
3.0 m 850 750 1500* 800 2400* 1900
(10') (1850) (1650) (3300) (1750) (5300) (4200)
1.5 m 650 550 1300* 750 2350* 1600
(5') (1450) (1200) (2850) (1650) (5150) (3500)
0m 700 550 1200* 700 2200* 1500
(0') (1550) (1200) (2650) (1550) (4850) (3300)
–1.5 m 750 650 1250* 850 2300* 1700 3600* 3600*
(–5') (1650) (1450) (2750) (1850) (5050) (3750) (7900) (7900)
–3.0 m 1000 900 2500* 1750 3300* 3300*
(–10') (2200) (2000) (5500) (3850) (7250) (7250)
Arm length 2000 mm (6'7") With blade and outrigger on ground
4.5 m 950 850 1000* 900 2400* 2000
(15') (2100) (1850) (3500) (2000) (5300) (4400)
3.0 m 800 700 1400* 800 2300* 1750
(10') (1750) (1550) (3100) (1750) (5050) (3850)
1.5 m 600 500 1200* 750 2200* 1500
(5') (1300) (1100) (2650) (1650) (4850) (3300)
0m 650 550 1100* 700 2100* 1450
(0') (1450) (1200) (2400) (1550) (4600) (3200)
–1.5 m 700 550 1150 800 2200* 1600 3500* 3500*
(–5') (1550) (1200) (2550) (1850) (4850) (3500) (7700) (7700)
–3.0 m 950 850 2300* 1700 3200* 3200*
(–10') (2100) (1850) (5050) (3750) (7050) (7050)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard NO. J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping
load.
2F-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4600 mm (15'1"), Bucket (SAE): 0.55 m3 (0.72 cu.yd), Tires:10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2100 mm (6'11")
7.5 m 2800* 2800*
(25') (6200) (6200)
6.0 m 2300* 2200 3450* 3300*
(20') (5100) (4800) (7600) (7300)
4.5 m 2150* 1650 3550* 1950 3800* 3250
(15') (4700) (3600) (7800) (4300) (8400) (7100)
3.0 m 2200* 1450 3850 1850 4700* 3050 6750* 5850
(10') (4800) (3200) (8500) (4100) (10300) (6700) (14800) (12900)
1.5 m 2350* 1350 3750 1800 5650* 2800 7400* 5250
(5') (5200) (3000) (8200) (4000) (12400) (6200) (16300) (11500)
0.0 m 2700* 1400 3650 1700 6000 2650 7550* 5000
(0') (5900) (3100) (8000) (3700) (13200) (5800) (16600) (11000)
–1.5 m 3400* 1650 3650 1700 5900 2650 8950* 5000 5800* 5800*
(–5') (7500) (3600) (8000) (3700) (13000) (5800) (19700) (11000) (12800) (12800)
–3.0 m 3850* 2250 4800* 2700 7200* 5150
(–10') (8500) (4900) (10600) (5900) (15800) (11300)
Blade and rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 2800* 2800*
(25') (6200) (6200)
6.0 m 2300* 2300* 3450* 3450*
(20') (5100) (5100) (7600) (7600)
4.5 m 2150* 2150* 3550* 2950 3800* 3800*
(15') (4700) (4700) (7880) (6500) (8400) (8400)
3.0 m 2200* 2200* 3850* 2900 4700* 4700* 6750* 6750*
(10') (4800) (4800) (8500) (6400) (10300) (10300) (14800) (14800)
1.5 m 2350* 2150 4000* 2800 5650* 4450 7400* 7400*
(5') (5200) (4700) (8800) (6200) (12400) (9800) (16300) (16300)
0.0 m 2700* 2250 3950 2700 6150* 4250 7550* 7550*
(0') (5900) (4900) (8700) (5900) (13500) (9300) (16600) (16600)
–1.5 m 3400* 2600 3900 2700 6000* 4200 8950* 8650 5800* 5800*
(–5') (7500) (5700) (8600) (5900) (13200) (9200) (19700) (19000) (12800) (12800)
–3.0 m 3850* 3550 4800* 4300 7200* 7200*
(–10') (8500) (7800) (10600) (9500) (15800) (15800)
Rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 2800* 2800*
(25') (6200) (6200)
6.0 m 2300* 2300* 3450* 3450*
(20') (5100) (5100) (7600) (7600)
4.5 m 2150* 2150* 3550* 2450 3800* 3800*
(15') (4700) (4700) (7800) (5400) (8400) (8400)
3.0 m 2200* 1850 3700* 2400 4700* 3900 6750* 6750*
(10') (4800) (4100) (8100) (5300) (10300) (8600) (14800) (14800)
1.5 m 2350* 1750 3600 2300 5650* 3650 7400* 7050
(5') (5200) (3800) (7900) (5100) (12400) (8000) (16300) (15500)
0.0 m 2700* 1850 3550 2250 5700 3500 7550* 6800
(0') (5900) (4100) (7800) (4900) (12500) (7700) (16600) (15000)
–1.5 m 3350 2150 3500 2250 5650 3450 8950* 6800 5800* 5800*
(–5') (7400) (4700) (7700) (4900) (12400) (7600) (19700) (15000) (12800) (12800)
–3.0 m 3850* 2900 4800* 3550 7200* 6950
(–10') (8500) (6400) (10600) (7800) (15800) (15300)
Blade above ground Arm length 2100 mm (6'11")
7.5 m 2800* 2800*
(25') (6200) (6200)
6.0 m 2300* 1800 3450* 2750
(20') (5100) (4000) (7600) (6000)
4.5 m 2150* 1350 3050 1600 3800* 2700
(15') (4700) (3000) (6700) (3500) (8400) (5900)
3.0 m 2200* 1150 3000 1550 4700* 2500 6750* 4750
(10') (4800) (2500) (6600) (3400) (10300) (5500) (14800) (10400)
1.5 m 2200 1100 2900 1450 4650 2300 7400* 4200
(5') (4800) (2400) (6400) (3200) (10200) (5100) (16300) (9200)
0.0 m 2300 1100 2800 1400 4500 2150 7550* 3950
(0') (5100) (2400) (6200) (3100) (9900) (4700) (16600) (8700)
–1.5 m 2650 1300 2800 1350 4550 2100 8950* 3950 5800* 5800*
(–5') (5800) (2900) (6200) (3000) (10000) (4600) (19700) (8700) (12800) (12800)
–3.0 m 3700 1850 4550 2200 7200* 4100
(–10') (8100) (4100) (10000) (4800) (15800) (9000)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4600 mm (15'1"), Bucket (SAE): 0.55 m3 (0.72 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2500 mm (8'2")
7.5 m 2200* 2200* 2500* 2500*
(25') (4800) (4800) (5500) (5500)
6.0 m 1850* 1850* 2000* 1950
(20') (4100) (4100) (4400) (4300)
4.5 m 1750* 1500 3300* 2000 3450* 3300*
(15') (3800) (3300) (7300) (4400) (7600) (7300)
3.0 m 1800* 1300 3700* 1900 4400* 3100 6050* 6050*
(10') (4000) (2900) (8100) (4200) (9700) (6800) (13300) (13300)
1.5 m 1950* 1250 3800 1800 5400* 2900 8650* 5400
(5') (4300) (2700) (8400) (4000) (11900) (6400) (19000) (11900)
0.0 m 2200* 1300 3700 1750 6000 2700 7950* 5050
(0') (4800) (2900) (8100) (3800) (13200) (5900) (17500) (11100)
–1.5 m 2750* 1450 3650 1700 5950 2650 9300* 5000 5250* 5250*
(–5') (6000) (3200) (8000) (3700) (13100) (5800) (20500) (11000) (11500) (11500)
–3.0 m 3750* 1950 5250* 2650 7900* 5100 8800* 8800*
(–10') (8200) (4300) (11500) (5800) (17400) (11200) (19400) (19400)
Blade and rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2200* 2200* 2500* 2500*
(25') (4800) (4800) (5500) (5500)
6.0 m 1850* 1850* 2000* 2000*
(20') (4100) (4100) (4400) (4400)
4.5 m 1750* 1750* 3300* 3000 3450* 3450*
(15') (3800) (3800) (7300) (6600) (7600) (7600)
3.0 m 1800* 1800* 3700* 2950 4400* 4400* 6050* 6050*
(10') (4000) (4000) (8100) (6500) (9700) (9700) (13300) (13300)
1.5 m 1950* 1950* 4050 2800 5400* 4500 8650* 8650*
(5') (4300)* (4300) (8900) (6200) (11900) (16500) (19000) (19000)
0.0 m 2200* 2050 3950 2750 6050* 4300 7950* 7950*
(0') (4800) (4500) (8700) (6000) (13300) (9500) (17500) (17500)
–1.5 m 2750* 2350 3900 2700 6100* 4250 9300* 8650 5250* 5250
(–5') (6000) (5200) (8600) (5900) (13400) (9300) (20500) (19000) (11500) (11500)
–3.0 m 3750* 3050 5250* 4250 7900* 7900* 8800* 8800*
(–10') (8200) (6700) (11500) (9300) (17400) (17400) (19400) (19400)
Rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2200* 2200* 2500* 2500*
(25') (4800) (4800) (5500) (5500)
6.0 m 1850* 1850* 2000* 2000*
(20') (4100) (4100) (4400) (4400)
4.5 m 1750* 1750* 3300* 2500 3450* 3450*
(15') (3800) (3800) (7300) (5500) (7600) (7600)
3.0 m 1800* 1700 3700* 2450 4400* 3950 6050* 6050*
(10') (4000) (3700) (8100) (5400) (9700) (8700) (13300) (13300)
1.5 m 1950* 1650 3650 2350 5400* 3700 8650* 7250
(5') (4300) (3600) (8000) (5200) (11900) (8100) (19000) (15900)
0.0 m 2200* 1700 3550 2250 5750 3550 7950* 6850
(0') (4800) (3700) (7800) (4900) (12600) (7800) (17500) (15100)
–1.5 m 2750* 1900 3500 2250 5650 3450 9300* 6800 5250* 5250*
(–5') (6000) (4200) (7700) (4900) (12400) (7600) (20500) (15000) (11500) (11500)
–3.0 m 3750* 2500 *5250 3450 7900* 6900 8800* 8800*
(–10') (8200) (5500) (11500) (7600) (17400) (15200) (19400) (19400)
Blade above ground Arm length 2500 mm (8'2")
7.5 m 2200* 2200* 2500* 2500*
(25') (4800) (4800) (5500) (5500)
6.0 m 1850* 1600 2000* 1600
(20') (4100) (3500) (4400) (3500)
4.5 m 1750* 1200 3100 1650 3450* 2750
(15') (3800) (2600) (6800) (3600) (7600) (6000)
3.0 m 1800* 1050 3000 1550 4400* 2600 6050* 5000
(10') (4000) (2300) (6600) (3400) (9700) (5700) (13300) (11000)
1.5 m 1950* 1000 2900 1500 4750 2350 8650* 4350
(5') (4300) (2200) (6400) (3300) (10400) (5200) (19000) (9600)
0.0 m 2100 1000 2800 1400 4550 2200 7950* 4000
(0') (4600) (2200) (6200) (3100) (10000) (4800) (17500) (8800)
–1.5 m 2400 1150 2800 1350 4450 2100 9300* 3950 5250* 5250*
(–5') (5300) (2500) (6200) (3000) (9800) (4600) (20500) (8700) (11500) (11500)
–3.0 m 3150 1550 4450 2150 7900* 4050 8800* 8800*
(–10') (6900) (3400) (9800) (4700) (17400) (8900) (19400) (19400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4800 mm (15'9"), Bucket: (SAE): 0.55 m3 (0.72 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2100 mm (6'11")
7.5 m 2700* 2700*
(25') (5900) (5900)
6.0 m 2200* 1950 3100* 3100*
(20') (4800) (4300) (6800) (6800)
4.5 m 2050* 1500 3250* 1900 3350* 3200
(15') (4500) (3300) (7100) (4200) (7400) (7000)
3.0 m 2050* 1300 3600* 1850 4450* 3000 6700* 5800
(10') (4500) (2900) (7900) (4100) (9800) (6600) (14700) (12800)
1.5 m 2150 1200 3750 1750 5350 2750
(5') (4700) (2600) (8200) (3800) (11800) (6000)
0.0 m 2450 1250 3650 1650 5850 2600 5300* 4900
(0') (5400) (2700) (8000) (3600) (12900) (5700) (11700) (10800)
–1.5 m 2950 1450 3600 1650 5750 2550 8600 4950 4550 4550
(–5') (6500) (3200) (7900) (3600) (12600) (5600) (18900) (10900) (10000) (10000)
–3.0 m 3500 1950 4850* 2600 7150 5050
(–10') (7700) (4300) (10700) (5700) (15700) (11100)
Blade and rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 2700* 2700*
(25') (5900) (5900)
6.0 m 2200* 2200* 3100* 3100*
(20') (4800) (4800) (6800) (6800)
4.5 m 2050* 2050* 3250* 2950 3550* 3550*
(15') (4500) (4500) (7100) (6500) (7800) (7800)
3.0 m 2050* 2050* 3600* 2850 4450* 4450* 6700* 6700*
(10') (4500) (4500) (7900) (6300) (9800) (9800) (14700) (14700)
1.5 m 2150* 2000 4000* 2750 5350* 4400
(5') (4700) (4400) (8800) (6000) (11800) (9700)
0.0 m 2450* 2050 3900 2700 5850* 4200 5300* 5300*
(0') (5400) (4500) (8600) (5900) (12900) (9200) (11700) (11700)
–1.5 m 2950* 2350 3900 2650 5750* 4150 8600* 8600* 4550* 4550*
(–5') (6500) (5200) (8600) (5800) (12600) (9100) (18900) (18900) (10000) (10000)
–3.0 m 3500* 3150 4850* 4250 7150* 7150*
(–10') (7700) (6900) (10700) (9300) (15700) (15700)
Rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 2700* 2700*
(25') (5900) (5900)
6.0 m 2200* 2200* 3100* 3100*
(20') (4800) (4800) (6800) (6800)
4.5 m 2050* 1950 3250* 2450 3550* 3550*
(15') (4500) (4300) (7100) (5400) (7800) (7880)
3.0 m 2050* 1700 3600* 2350 4450* 3850 6700* 6700*
(10') (4500) (3700) (7900) (5200) (9800) (8500) (14700) (14700)
1.5 m 2150* 1600 3600 2250 5350* 3600
(5') (4700) (3500) (7900) (4900) (11800) (7900)
0.0 m 2450* 1700 3500 2200 5650 3450 5300* 5300*
(0') (5400) (3700) (7700) (4800) (12400) (7600) (11700) (11700)
–1.5 m 2950* 1900 3500 2150 5600 3400 8600* 6750 4550* 4550*
(–5') (6500) (4200) (7700) (4700) (12300) (7500) (18900) (14800) (10000) (10000)
–3.0 m 3500* 2600 4850* 3450 7150* 6900
(–10') (7700) (5700) (10700) (7600) (15700) (15200)
Blade above ground Arm length 2100 mm (6'11")
7.5 m 2700* 2700*
(25') (5900) (5900)
6.0 m 2200* 1600 3100* 2750
(20') (4800) (3500) (6800) (6000)
4.5 m 2050* 1200 3050 1650 3550* 2700
(15') (4500) (2600) (6700) (3600) (7800) (5900)
3.0 m 2050* 1000 2950 1600 4450* 2450 6700* 4700
(10') (4500) (2200) (6500) (3500) (9800) (5400) (14700) (10300)
1.5 m 2050 950 2850 1500 4650 2250
(5') (4500) (2100) (6300) (3300) (10200) (4900)
0.0 m 2100 1000 2750 1400 4450 2100 5300* 3850
(0') (4600) (2200) (6000) (3100) (9800) (4600) (11700) (8500)
–1.5 m 2400 1150 2750 1400 4400 2050 8600* 3900 4550* 4550*
(–5') (5300) (2500) (6000) (3100) (9700) (4500) (18900) (8600) (10000) (10000)
–3.0 m 3250 1600 4500 2100 7150* 4000
(–10') (7100) (3500) (9900) (4600) (15700) (8800)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4800 mm (15'9"), Bucket: (SAE): 0.55 m3 (0.72 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2500 mm (8'2")
7.5 m 2100* 2100* 3000* 3000*
(25') (4600) (4600) (6600) (6600)
6.0 m 1800* 1700 2900* 1950
(20') (4000) (3700) (6400) (4300)
4.5 m 1650* 1350 3000* 1950 3200* 3200*
(15') (3600) (3000) (6600) (4300) (7000) (7000)
3.0 m 1650* 1200 3400* 1900 4150* 3100 5900* 5900*
(10') (3600) (2600) (7500) (4200) (9100) (6800) (13000) (13000)
1.5 m 1750* 1100 3750 1750 5150* 2800 6300* 5300
(5') (3800) (2400) (8200) (3800) (11300) (6200) (13900) (11700)
0.0 m 2000* 1150 3650 1700 5800* 2650 5700* 4950
(0') (4400) (2500) (7900) (3700) (12800) (5800) (12550) (10900)
–1.5 m 2400* 1300 3600 1650 5850* 2550 8450* 4900
(–5') (5300) (2900) (7900) (3600) (12900) (5600) (18600) (10800)
–3.0 m 3300* 1700 5200* 2600 7750* 5000
(–10') (7300) (3700) (11400) (5700) (17000) (11000)
Blade and rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2100* 2100*
(25') (4600) (4600)
6.0 m 1800* 1800* 2900* 2900*
(20') (4000) (4000) (6400) (6400)
4.5 m 1650* 1650* 3000* 3000 3200* 3200*
(15') (3600) (3600) (6600) (6600) (7000) (7000)
3.0 m 1650* 1650* 3400* 2900 4150* 4150* 5900* 5900*
(10') (3600) (3600) (7500) (6400) (9100) (9100) (13000) (13000)
1.5 m 1750* 1750* 3850* 2800 5150* 4450 6300* 6300*
(5') (3800) (3800) (8500) (6200) (11300) (9800) (13900) (13900)
0.0 m 2000* 1900 3900 2700 5800* 4250 5700* 5700*
(0') (4400) (4200) (8600) (5900) (12800) (9300) (12500) (12500)
–1.5 m 2400* 2150 3900 2650 5850* 4200 8450* 8450* 4200* 4200*
(–5') (5300) (4700) (8600) (5800) (12900) (9200) (18600) (18600) (9200) (9200)
–3.0 m 3300* 2700
(–10') (7300) (5900)
Rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2100* 2100*
(25') (4600) (4600)
6.0 m 1800* 1800* 2900* 2500
(20') (4000) (4000) (6400) (5500)
4.5 m 1650* 1650* 3000* 2500 3200* 3200*
(15') (3600) (3600) (6600) (5500) (7000) (7000)
3.0 m 1650* 1550 3400* 2400 4150* 3950 5900* 5900*
(10') (3600) (3400) (7500) (5300) (9100) (8700) (13000) (13000)
1.5 m 1750* 1500 3650 2300 5150* 3650 6300* 6300*
(5') (3800) (3300) (8000) (5100) (11300) (8000) (13900) (13900)
0.0 m 2000* 1550 3500 2200 5700 3450 5700* 5700*
(0') (4400) (3400) (7700) (4800) (12500) (7600) (12500) (12500)
–1.5 m 2400* 1750 3500 2150 5600 3400 8450* 6750 4200* 4200*
(–5') (5300) (3800) (7700) (4700) (12300) (7500) (18600) (14800) (9200) (9200)
–3.0 m 3300* 2250 5200* 3450 7750* 8650
(–10') (7300) (4900) (11400) (7600) (17000) (19000)
Blade above ground Arm length 2500 mm (8'2")
7.5 m 2100* 2100* 3000* 2750
(25') (4600) (4600) (6600) (6000)
6.0 m 1800* 1400 2900* 1600
(20') (4000) (3100) (6400) (3500)
4.5 m 1650* 1100 3000* 1600 3200* 2750
(15') (3600) (2400) (6600) (3500) (7000) (6000)
3.0 m 1650* 950 3000 1550 4150* 2550 5900* 4950
(10') (3600) (2100) (6600) (3400) (9100) (5600) (13000) (10900)
1.5 m 1750* 850 2900 1450 4700 2300 6300 4200
(5') (3800) (1900) (6400) (3200) (10300) (5000) (13900) (9200)
0.0 m 1950 900 2800 1350 4500 2100 5700 3900
(0') (4300) (2000) (6200) (3000) (9900) (4600) (12500) (8600)
–1.5 m 2200 1050 2750 1300 4400 2050 8450* 3850 4200* 4200*
(–5') (4800) (2300) (6000) (2900) (9700) (4500) (18600) (8500) (9200) (9200)
–3.0 m 2800 1350 4450 2100 7750* 3950
(–10') (6200) (3000) (9800) (4600) (17000) (8700)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
Conditions:
Boom: 4800 mm (15'9"), Bucket (SAE): 0.55 m3 (0.72 cu.yd), Tires:10.00-20-16PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade and rear outrigger on ground Arm length 2600 mm (8'6")
7.5 m 1950* 1950*
(25') (4300) (4300)
6.0 m 1600* 1600* 2600* 2600*
(20') (3500) (3500) (5700) (5700)
4.5 m 1500* 1500* 2650* 2650* 2850* 2850*
(15') (3300) (3300) (5800) (5800) (6300) (6300)
3.0 m 1500* 1500* 3000* 2650 3700* 3700* 5300* 5300*
(10') (3300) (3300) (6600) (5800) (8100) (8100) (11700) (11700)
1.5 m 1600* 1550 3450* 2500 4600* 4050 6850* 6850*
(5') (3500) (3400) (7600) (5500) (10100) (8900) (15100) (15100)
0.0 m 1750* 1600 3600 2350 5250* 3800 5700* 5700*
(0') (3800) (3500) (7900) (5200) (11500) (8400) (12500) (12500)
–1.5 m 2100* 1800 3550 2300 5300* 3700 8250* 7750 4000* 4000*
(–5') (4600) (4000) (7800) (5100) (11700) (8100) (18100) (17000) (8800) (8800)
–3.0 m 2900* 2350 3100* 2400 4750* 3750 7150* 7150* 7200* 7200*
(–10') (6400) (5200) (6800) (5300) (10400) (8200) (15700) (15700) (15800) (15800)
Front and rear outrigger above ground Arm length 2600 mm (8'6")
7.5 m 1950* 1950*
(25') (4300) (4300)
6.0 m 1600* 1600* 2600* 2600*
(20') (3500) (3500) (5700) (5700)
4.5 m 1500* 1500* 2650* 2650* 2850* 2850*
(15') (3300) (3300) (5800) (5800) (6300) (6300)
3.0 m 1500* 1500* 3000* 3000* 3700* 3700* 5300* 5300*
(10') (3300) (3300) (6600) (6600) (8100) (8100) (11700) (11700)
1.5 m 1600* 1600* 3450* 3400 4600* 4600* 6850* 6850*
(5') (3500) (3500) (7600) (7500) (10100) (10100) (15100) (15100)
0.0 m 1750* 1750* 3450 2350 5250* 5250* 5700* 5700*
(0') (3800) (3800) (7600) (5200) (11500) (11500) (12500) (12500)
–1.5 m 2100* 2100* 3550 2300 5300* 5200 8250* 8250* 4000* 4000*
(–5') (4600) (4600) (7800) (5100) (11700) (11400) (18100) (18100) (8800) (8800)
–3.0 m 2900* 2900* 3100* 3100* 4750* 4750* 7150* 7150* 7200* 7200*
(–10') (6400) (6400) (6800) (6800) (10400) (10400) (15700) (15700) (15800) (15800)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4600 mm (15'1"), Bucket (SAE): 0.62 m3 (0.81 cu.yd), Tires:10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2100 mm (6'11")
7.5 m 3650* 3650*
(25') (8000) (8000)
6.0 m 2750* 2750* 4100* 4100
(20') (6050) (6050) (9000) (9000)
4.5 m 2500* 2350 3900* 2500 4450* 4050
(15') (5500) (5150) (8550) (5500) (9800) (9800)
3.0 m 2450* 2050 4350 2450 5400* 3900
(10') (5400) (4500) (9550) (5400) (11850) (8550)
1.5 m 2600* 1950 4700* 2400 6250* 3600
(5') (5700) (4300) (10300) (5250) (13750) (7900)
0.0 m 2950* 2050 4850* 2350 6700* 3600 5950* 5950*
(0') (6500) (4500) (10650) (5150) (14750) (7900) (13100) (13100)
–1.5 m 3700* 2400 6300* 3550 9300* 6700 5450* 5450*
(–5') (8100) (5250) (13850) (7800) (20450) (14750) (12000) (12000)
–3.0 m 3950* 3450 4500* 3700 7050* 6900
(–10') (8700) (7600) (9900) (8150) (15500) (15150)
Blade and rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 3650* 3650*
(25') (8000) (8000)
6.0 m 2750* 2750* 4100* 4100*
(20') (6050) (6050) (9000) (9000)
4.5 m 2500* 2500* 3900* 3850 4450* 4450*
(15') (5500) (5500) (8550) (8450) (9800) (9800)
3.0 m 2450* 2450* 4350* 3800 5400* 5400*
(10') (5400) (5400) (9550) (8350) (11850) (11850)
1.5 m 2600* 2600* 4700* 3750 6250* 5800
(5') (5700) (5700) (10350) (8250) (13750) (12750)
0.0 m 2950* 2950* 4850* 3700 6700* 5750 5950* 5950*
(0') (6500) (6500) (10650) (8100) (14750) (12650) (13100) (13100)
–1.5 m 3700* 3700* 6300* 5750 9300* 9300* 5450* 5450*
(–5') (8100) (8100) (13850) (12650) (20450) (20450) (12000) (12000)
–3.0 m 3950* 3950* 4500* 4500* 7050* 7050*
(–10') (8700) (8700) (9900) (9900) (15500) (15500)
Rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 3650* 3650*
(25') (8000) (8000)
6.0 m 2750* 2750* 4100* 4100*
(20') (6050) (6050) (9000) (9000)
4.5 m 2500* 2500* 3900* 3200 4450* 4450*
(15') (5500) (5500) (8550) (7050) (9800) (9800)
3.0 m 2450* 2450* 4350* 3150 5400* 5000
(10') (5400) (5400) (9550) (6900) (11850) (11000)
1.5 m 2600* 2550 4400* 3100 6250* 4750
(5') (5700) (5600) (9650) (6800) (13750) (10450)
0.0 m 2950* 2650 4350 3050 6700* 4700 5950* 5950*
(0') (6500) (5800) (9550) (6700) (14750) (10350) (13100) (13100)
–1.5 m 3700* 2350 6300* 4700 9300* 9300* 5450* 5450*
(–5') (8100) (5150) (13850) (10350) (20450) (20450) (12000) (12000)
–3.0 m 3950* 3950 4500* 4500* 7050* 7050*
(–10') (8700) (8700) (9900) (9900) (15500) (15500)
Blade above ground Arm length 2100 mm (6'11")
7.5 m 3650* 3650*
(25') (8000) (8000)
6.0 m 2750* 2550 4100* 3400*
(20') (6050) (5600) (9000) (7450)
4.5 m 2500* 1900 3800 2500 4450* 3350
(15') (5500) (4150) (8350) (5500) (9800) (7350)
3.0 m 2450* 1650 7500 2000 5400* 3200
(10') (5400) (3600) (16500) (4400) (11850) (7050)
1.5 m 2600* 1550 3700 1950 5800 2950
(5') (5500) (3400) (8100) (4300) (12750) (6500)
0.0 m 2950* 1650 3650 1900 5750 2900 5950* 5250
(0') (6500) (3600) (8700) (4150) (12650) (6350) (13100) (11550)
–1.5 m 3700* 1950 5750 2900 9300* 5350 5450* 5450*
(–5') (8100) (4300) (12750) (6350) (20450) (11750) (12000) (12000)
–3.0 m 3950* 2800 4500* 3000 7050* 5500
(–10') (8700) (6150) (9900) (6600) (15500) (12100)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4600 mm (15'1"), Bucket (SAE): 0.62 m3 (0.81 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2500 mm (8'2")
7.5 m 2650* 2650*
(25') (5800) (5800)
6.0 m 2100* 2100* 3600* 3600*
(20') (4600) (4600) (7900) (7900)
4.5 m 1950* 1950* 3800* 2500 4050* 4050*
(15') (4300) (4300) (8350) (5500) (8900) (8900)
3.0 m 1950* 1850* 4150* 2450 5050* 3900 7250* 7250*
(10') (4300) (4050) (9100) (5400) (11100) (8550) (15950) (15950)
1.5 m 2050* 1800 4550* 2400 6050* 3700 6150* 6150*
(5') (4500) (3950) (10000) (5250) (13300) (8150) (13500) (13500)
0.0 m 2350* 1850 4800* 2300 6650* 3550 6500* 6500*
(0') (5150) (4050) (10550) (5050) (14600) (7800) (14300) (14300)
–1.5 m 2900* 2150 4500* 2300 6450* 3550 9750* 6700 5000* 5000*
(–5') (6350) (4700) (9900) (5050) (14200) (7800) (21450) (14750) (11000) (11000)
–3.0 m 3900* 2900 5250* 3600 7850* 6850
(–10') (8550) (6350) (11550) (7900) (17250) (15050)
Blade and rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2650* 2650*
(25') (5800) (5800)
6.0 m 2100* 2100* 3600* 3600*
(20') (4600) (4600) (7900) (7900)
4.5 m 1950* 1950* 3800* 3800* 4050* 4050*
(15') (4300) (4300) (8350) (8350) (8900) (8900)
3.0 m 1950* 1950* 4150* 3800 5050* 5050* 7250* 7250*
(10') (4300) (4300) (9100) (8350) (11100) (11100) (15950) (15950)
1.5 m 2050* 2050* 4550* 3750 6050* 5900 6150* 6150*
(5') (4500)* (4500) (10000) (8250) (13300) (12950) (13500) (13500)
0.0 m 2350* 2350* 4800* 3650 6650* 5750 6500* 6500*
(0') (5150) (5150) (10550) (8000) (14600) (12650) (14300) (14300)
–1.5 m 2900* 2900* 4500* 3650 6450* 5700 9750* 9750* 5000* 5000*
(–5') (6350) (6350) (9900) (8000) (14200) (12550) (21450) (21450) (11000) (11000)
–3.0 m 3900* 3900* 5250* 5250* 7850* 7850*
(–10') (8550) (8550) (11550) (11550) (17250) (17250)
Rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2650* 2650*
(25') (5800) (5800)
6.0 m 2100* 2100* 3600* 3600*
(20') (4600) (4600) (7900) (7900)
4.5 m 1950* 1950* 3800* 3200 4050* 4050*
(15') (4300) (4300) (8350) (7050) (8900) (8900)
3.0 m 1950* 1950* 4150* 3150 5050* 5050* 7250* 7250*
(10') (4300) (4300) (9100) (6900) (11100) (11100) (15950) (15950)
1.5 m 2050* 2050* 4400 3100 6050* 4800 6150* 6150*
(5') (4500) (4500) (9650) (6800) (13300) (10550) (13500) (13500)
0.0 m 2350* 2350* 4350 3000 6650* 4700 6500* 6500*
(0') (5150) (5150) (9550) (6600) (14600) (10350) (14300) (14300)
–1.5 m 2900* 2800 4350 3000 6450* 4650 9750* 9250 5000* 5000*
(–5') (6350) (6150) (9550) (9550) (14200) (10200) (21450) (20350) (11000) (11000)
–3.0 m 3900* 3750 5250* 4700 7850* 7850*
(–10') (8550) (8250) (11550) (10350) (17250) (17250)
Blade above ground Arm length 2500 mm (8'2")
7.5 m 2650* 2650*
(25') (5800) (5800)
6.0 m 2100* 2100* 3600* 3400
(20') (4600) (4600) (5790) (7450)
4.5 m 1950* 1700 3800* 2050 4050* 3400
(15') (4300) (3750) (8350) (4500) (8900) (7450)
3.0 m 1950* 1500 3750 2000 5050* 3200 7250* 5950
(10') (4300) (3300) (8250) (4400) (11100) (11100) (15950) (13100)
1.5 m 2050* 1400 3700 1950 5900 3000 6150* 5500
(5') (4500) (3050) (8150) (4300) (12950) (6600) (13500) (12100)
0.0 m 2350* 1500 3600 1850 5750 2900 6500* 5300
(0') (5150) (3300) (7900) (4050) (12650) (6350) (14300) (11650)
–1.5 m 2900* 1700 3600 1850 5700 2850 9750* 5300 5000* 5000*
(–5') (6350) (3750) (7900) (4050) (12550) (6250) (21450) (11650) (11000) (11000)
–3.0 m 3900* 2350 5250* 2900 7850* 5400
(–10') (8550) (5150) (11550) (6350) (17250) (11850)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-24
AH_25.book Page 25 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4600 mm (15'1"), Bucket (SAE): 0.62 m3 (0.81 cu.yd), Tires:10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 3000 mm (9'10")
7.5 m 2000* 2000*
(25') (4400) (4400)
6.0 m 1650* 1650* 2650* 2500
(20') (3600) (3600) (5800) (5500)
4.5 m 1550* 1550* 3400* 2500 3500* 3500*
(15') (3400) (3400) (7450) (5500) (7700) (7700)
3.0 m 1550* 1550* 3800* 2450 4500* 3950 6150* 6150*
(10') (3400) (3400) (8350) (5400) (9900) (8700) (13500) (13500)
1.5 m 1650* 1550* 4300* 2350 5650* 3700 9100* 6950
(5') (3600) (3400) (9450) (5150) (12400) (8150) (20000) (15300)
0.0 m 1850* 1600 4650* 2250 6400* 3500 6800* 6600
(0') (4050) (3500) (10200) (4950) (14050) (7700) (14950) (14500)
–1.5 m 2200* 1800 4650* 2250 6500* 3450 9350* 6550 4300* 4300*
(–5') (4850) (3950) (10200) (4950) (14300) (7600) (20550) (14400) (9450) (9450)
–3.0 m 3050* 2350 5650* 3400 8600* 6650 7700* 7700*
(–10') (6700) (5150) (12400) (7450) (18900) (14600) (16950) (16950)
Blade and rear outrigger on ground Arm length 3000 mm (9'10")
7.5 m 2000* 2000*
(25') (4400) (4400)
6.0 m 1650* 1650* 2650* 2650*
(20') (3600) (3600) (5800) (5800)
4.5 m 1550* 1550* 3400* 3400* 3500* 3500*
(15') (3400) (3400) (7450) (7450) (7700) (7700)
3.0 m 1550* 1550* 3800* 3800* 4500* 4500* 6150* 6150*
(10') (3400) (3400) (8350) (8350) (9900) (9900) (13500) (13500)
1.5 m 1650* 1650* 4300* 3700 5650* 5650* 9100* 9100*
(5') (3600) (3600) (9450) (8150) (12400) (12400) (20000) (20000)
0.0 m 1850* 1850* 4650* 3600 6400* 5700 6800* 6800*
(0') (4050) (6500) (10200) (7900) (14050) (12550) (14950) (14950)
–1.5 m 2200* 2200* 4650* 3600 6500* 5650 9350* 9350* 4300* 4300*
(–5') (4850) (4850) (10200) (7900) (14300) (12650) (20550) (20550) (9450) (9450)
–3.0 m 3050* 3050* 5650* 5600 8600* 8600* 7700* 7700*
(–10') (6700) (6700) (12400) (12300) (18900) (18900) (16950) (16950)
Rear outrigger on ground Arm length 3000 mm (9'10")
7.5 m 2000* 2000*
(25') (4400) (4400)
6.0 m 1650* 1650* 2650* 2650*
(20') (3600) (3600) (5800) (5800)
4.5 m 1550* 1550* 3400* 3200 3500* 3500*
(15') (3400) (3400) (7450) (7050) (7700) (7700)
3.0 m 1550* 1550* 3800* 2450 4500* 4500* 6150* 6150*
(10') (3400) (3400) (8350) (5400) (9900) (9900) (13500) (13500)
1.5 m 1650* 1650* 4300* 2350 5650* 4850 9100* 9100*
(5') (3600) (3600) (9450) (5150) (12400) (10650) (20000) (20000)
0.0 m 1850* 1850* 4650* 3600 6400* 4650 6800* 6800*
(0') (4050) (6500) (10200) (7900) (14050) (10200) (14950) (14950)
–1.5 m 2200* 2200* 4650* 3600 6500* 4550 9350* 9100 4300* 4300*
(–5') (4850) (4850) (10200) (7900) (14300) (10000) (20550) (20000) (9450) (9450)
–3.0 m 3050* 3050* 5650* 4500 8600* 8600* 7700* 7700*
(–10') (6700) (6700) (12400) (9900) (18900) (18900) (16950) (16950)
Blade above ground Arm length 3000 mm (9'10")
7.5 m 2000* 2000*
(25') (4400) (4400)
6.0 m 1650* 1650* 2650* 2050
(20') (3600) (3600) (5800) (4500)
4.5 m 1550* 1450 3400* 2050 3500* 3400
(15') (3400) (3200) (7450) (4500) (7700) (7450)
3.0 m 1650* 1250 3750 2000 4500* 3250 6150* 6150*
(10') (3600) (3750) (8250) (4400) (9900) (7150) (13500) (13500)
1.5 m 1650* 1200 3650 1900 5650* 3000 9100* 5500
(5') (3600) (2650) (8000) (4150) (12400) (6600) (20000) (12100)
0.0 m 1850* 1250 3550 1800 5700 2850 6800* 5200
(0') (4050) (2750) (7800) (3950) (12550) (6250) (14950) (11450)
–1.5 m 2200* 1450 3500 1800 5650 2750 9350* 5150 4300* 4300*
(–5') (4850) (3200) (7700) (3950) (12740) (6050) (20550) (11300) (9450) (9450)
–3.0 m 3050* 1900 5600 2750 8600* 5250 7700* 7700*
(–10') (6700) (4150) (12300) (6050) (18900) (11550) (16950) (16950)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-25
AH_25.book Page 26 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4800 mm (15'9"), Bucket: (SAE): 0.62 m3 (0.81 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2100 mm (6'11")
7.5 m 3300* 3300*
(25') (7250) (7250)
6.0 m 2550* 2550* 4250* 4050*
(20') (5600) (5600) (9350) (8900)
4.5 m 2350* 2150 4350* 2450 4750* 4000
(15') (5150) (5150) (9550) (5400) (10450) (8800)
3.0 m 2400* 1900 4700* 2400 5900* 3800
(10') (5250) (4150) (10350) (5250) (12950) (8350)
1.5 m 2550* 1800 5150* 2300 6950* 3650
(5') (5600) (3950) (11300) (5050) (15300) (8000)
0.0 m 2950* 1900 5300* 2250 7050* 3500 4800* 4800*
(0') (6500) (4150) (11650) (4950) (15500) (7700) (10500) (10500)
–1.5 m 3700* 2200 4800* 2250 7050* 3500 10050* 6700
(–5') (8150) (4850) (10550) (4950) (15500) (7700) (22100) (14750)
–3.0 m 4500* 3100 5450* 3600 8150* 6850
(–10') (9900) (6800) (12000) (7900) (17900) (15050)
Blade and rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 3350* 3350*
(25') (7350) (7350)
6.0 m 2600* 2600* 4250* 4250*
(20') (5700) (5700) (9350) (9350)
4.5 m 2400* 2400* 4350* 3800 4800* 4800*
(15') (5250) (5250) (9550) (8350) (10550) (10550)
3.0 m 2450* 2450* 4700* 3750 5900* 5900*
(10') (5400) (5400) (10350) (8250) (12950) (12950)
1.5 m 2600* 2600* 5150* 3700 6950* 5800
(5') (5700) (5700) (11300) (8150) (15300) (12750)
0.0 m 2950* 2950* 5300* 3650 7350* 5700 4850* 4850*
(0') (6500) (6500) (11650) (8000) (16150) (12550) (10650) (10650)
–1.5 m 3750* 3550 4850* 3650 7050* 5700 10100* 10100*
(–5') (8250) (7800) (10650) (8000) (15500) (12550) (22200) (22200)
–3.0 m 4500* 4500* 5450* 5450* 8100* 8100*
(–10') (9900) (9900) (12000) (12000) (17900) (17900)
Rear outrigger on ground Arm length 2100 mm (6'11")
7.5 m 3350* 3350*
(25') (7350) (7350)
6.0 m 2600* 2600* 4250* 4250*
(20') (5700) (5700) (9350) (9350)
4.5 m 2400* 2400* 4350* 3150 4800* 4800*
(15') (5250) (5250) (9550) (6900) (10550) (10550)
3.0 m 2450* 2450* 4450 3100 5900* 4950
(10') (5400) (5400) (9800) (6800) (12950) (10900)
1.5 m 2600* 2400 4400 3050 6950* 4750
(5') (5700) (5250) (9650) (6700) (15300) (10450)
0.0 m 2950* 2500 4300 2950 6950 4650 4850* 4850*
(0') (6500) (5500) (9450) (6500) (15300) (10200) (10650) (10650)
–1.5 m 3750* 2900 4300 3000 6950 4600 10100* 9200
(–5') (8250) (6350) (9450) (6600) (15300) (10100) (22200) (20250)
–3.0 m 4500* 4050 5450* 4700 8100* 8100*
(–10') (9900) (8900) (12000) (10350) (17900) (17900)
Blade above ground Arm length 2100 mm (6'11")
7.5 m 3350* 3350*
(25') (7350) (7350)
6.0 m 2600* 2600* 4250* 3950
(20') (5700) (5700) (9350) (8700)
4.5 m 2400* 2100 3750 2350 4800* 3850
(15') (5400) (4600) (8250) (5150) (10550) (8450)
3.0 m 2450* 1800 3700 2300 5900* 3700
(10') (4500) (3950) (8150) (5050) (12950) (8150)
1.5 m 2600* 1750 3650 2250 5850 3500
(5') (5700) (3850) (8000) (4950) (12850) (7700)
0.0 m 2950* 1850 3550 2200 5700 3400 4850* 4850*
(0') (6500) (4050) (7800) (4850) (12550) (7450) (10650) (10650)
–1.5 m 3500 2150 3600 2200 5700 3350 10100* 6400
(–5') (5300) (4700) (7900) (4850) (12550) (7350) (22200) (14050)
–3.0 m 4500* 3000 5450* 3450 8100* 6600
(–10') (9900) (6600) (12000) (7600) (15700) (14500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-26
AH_25.book Page 27 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4800 mm (15'9"), Bucket: (SAE): 0.62 m3 (0.81 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 2500 mm (8'2")
7.5 m 2500* 2500*
(25') (5500) (5500)
6.0 m 2050* 2050* 3800* 3800*
(20') (4500) (4500) (8350) (8350)
4.5 m 1900* 1900* 4000* 2450 4350* 4050
(15') (4150) (4150) (8800) (5400) (9550) (8900)
3.0 m 1900* 1700 4450* 2400 5500* 3850 8300* 7400
(10') (4150) (3750) (9800) (5250) (12100) (8450) (18250) (16250)
1.5 m 2050* 1650 4950* 2300 6650* 3650
(5') (4500) (3600) (10900) (5050) (14600) (8000)
0.0 m 2350* 1700 5300* 2250 7300* 3500 5350* 5350*
(0') (5150) (3750) (11650) (4950) (16050) (5800) (11750) (11750)
–1.5 m 2900* 2000 5100* 2250 7150* 3450 9100* 6600 4550* 4550*
(–5') (6350) (4400) (11200) (4950) (15700) (5600) (20000) (14500) (10000) (10000)
–3.0 m 4200* 2650 6050* 3500 8950* 6700
(–10') (9250) (5800) (13300) (7700) (19700) (14750)
Blade and rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2500* 2500*
(25') (5500) (5500)
6.0 m 2050* 2050* 3800* 3800*
(20') (4500) (4500) (8350) (8350)
4.5 m 1900* 1900* 4000* 3850 4350* 4350*
(15') (4150) (4150) (8800) (8450) (9550) (9550)
3.0 m 1900* 1900* 4450* 3800 5500* 5500* 8300* 8300*
(10') (4150) (4150) (9800) (8350) (12100) (12100) (18250) (18250)
1.5 m 2050* 2050* 4950* 3700 6650* 5850
(5') (4500) (4500) (10900) (8150) (14600) (12850)
0.0 m 2350* 2350* 5300* 3600 7300* 5700 5350* 5350*
(0') (5150) (5150) (11650) (7900) (16050) (12550) (11750) (11750)
–1.5 m 2900* 2900* 5100* 3600 7150* 5650 9100* 9100* 4550* 4550*
(–5') (6350) (6350) (11200) (7900) (15700) (12400) (20000) (20000) (10000) (10000)
–3.0 m 4200* 4200* 6050* 5700 8950* 8950*
(–10') (9250) (9250) (13300) (12550) (19700) (19700)
Rear outrigger on ground Arm length 2500 mm (8'2")
7.5 m 2500* 2500*
(25') (5500) (5500)
6.0 m 2050* 2050* 3800* 3800*
(20') (4500) (4500) (8350) (8350)
4.5 m 1900* 1900* 4000* 3200 4350* 4350*
(15') (4150) (4150) (8800) (7050) (9550) (9550)
3.0 m 1900* 1900* 4450* 3100 5500* 5050 8300* 8300*
(10') (4150) (4150) (9800) (6800) (12100) (11100) (18250) (18250)
1.5 m 2050* 2050* 4400 3050 6650* 4750
(5') (4500) (4500) (9650) (6700) (14500) (10450)
0.0 m 2350* 2250 4300 2950 6950 4650 5350* 5350*
(0') (5150) (4950) (9450) (6500) (15300) (10200) (11750) (11750)
–1.5 m 2900* 2600 4300 2950 6900 4600 9100* 9100* 4550* 4550*
(–5') (6350) (5700) (9450) (6500) (15150) (10100) (20000) (20000) (10000) (10000)
–3.0 m 4200* 3450 6050* 4650 8950* 8950*
(–10') (9250) (7600) (13300) (10200) (19700) (19700)
Blade above ground Arm length 2500 mm (8'2")
7.5 m 2500* 2500*
(25') (5500) (5500)
6.0 m 2050* 2050* 3800* 3400
(20') (4500) (4500) (8350) (7450)
4.5 m 1900* 1550 3800 2000 4350* 3350
(15') (4150) (3400) (8350) (4400) (9550) (7350)
3.0 m 1900* 1350 3750 1950 5500* 3150 8300* 5950
(10') (4150) (2950) (8250) (4300) (12100) (6900) (18250) (13100)
1.5 m 2050* 1300 3650 1850 5850 2950
(5') (4500) (2850) (8000) (4050) (12850) (6500)
0.0 m 2350* 1350 3550 1800 5700 2800 5350* 5200
(0') (5150) (2950) (7800) (3950) (12550) (6150) (11750) (11450)
–1.5 m 2900* 1600 3550 1800 5650 2800 9100* 5200 4550* 4550*
(–5') (6350) (3500) (7800) (3950) (12400) (6150) (20000) (11450) (10000) (10000)
–3.0 m 4150 2100 5700 2850 8950* 5300
(–10') (9100) (4600) (12550) (6250) (19700) (11650)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-27
AH_25.book Page 28 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 4800 mm (15'9"), Bucket: (SAE): 0.62 m3 (0.81 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade on ground Arm length 3000 mm (9'10")
7.5 m 1900* 1900*
(25') (4150) (4150)
6.0 m 1550* 1550* 2900* 2500
(20') (3400) (3400) (6350) (5500)
4.5 m 1450* 1450* 3600* 2450 3750* 3750*
(15') (3200) (3200) (7900) (5400) (8250) (8250)
3.0 m 1500* 1500* 4100* 2400 4900* 3850 6950* 6950*
(10') (3300) (3300) (9000) (5250) (10750) (8450) (15300) (15300)
1.5 m 1550* 1400 4700* 2300 6200* 3600 6550* 6550*
(5') (3400) (3050) (10350) (5050) (13650) (7900) (14400) (14400)
0.0 m 1750* 1500 5100* 2200 7050* 3450 5550* 5550*
(0') (3850) (3300) (11200) (4850) (15500) (7600) (12200) (12200)
–1.5 m 2150* 1650 5150* 2150 7200* 3350 8050* 6450 3850* 3850*
(–5') (4700) (3600) (11300) (4700) (15850) (7350) (17700) (14200) (8450) (8450)
–3.0 m 2950* 2150 4300* 2200 6500* 3400 9700* 6550 7050* 7050*
(–10') (6500) (4700) (9450) (4850) (14300) (7450) (21350) (14400) (15500) (15500)
Blade and rear outrigger on ground Arm length 3000 mm (9'10")
7.5 m 1900* 1900*
(25') (4150) (4150)
6.0 m 1550* 1550* 2900* 2900*
(20') (3400) (3400) (6350) (6350)
4.5 m 1450* 1450* 3600* 3600* 3750* 3750*
(15') (3200) (3200) (7900) (7900) (8250) (8250)
3.0 m 1500* 1500* 4100* 3750 4900* 4900* 6950* 6950*
(10') (3300) (3300) (9000) (8250) (10750) (10750) (15300) (15300)
1.5 m 1550* 1550* 4700* 3650 6200* 5850 6550* 6550*
(5') (3400) (3400) (10350) (8000) (13650) (12850) (14400) (14400)
0.0 m 1750* 1750* 5100* 3550 7050* 5650 5550* 5550*
(0') (3850) (3850) (11200) (7800) (15500) (12400) (12200) (12220)
–1.5 m 2150* 2150* 5150* 3500 7200* 5550 8050* 8050* 3850* 3850*
(–5') (4700) (4700) (11300) (7700) (15850) (12200) (17700) (17700) (8450) (8450)
–3.0 m 2950* 2950* 4300* 3550 6500* 5600 9700* 9700* 7050* 7050*
(–10') (6500) (6500) (9450) (7800) (14300) (12300) (21350) (21350) (15500) (15500)
Rear outrigger on ground Arm length 3000 mm (9'10")
7.5 m 1900* 1900*
(25') (4150) (4150)
6.0 m 1550* 1550* 2900* 2900*
(20') (3400) (3400) (6350) (6350)
4.5 m 1450* 1450* 2900* 3200 3750* 3750*
(15') (3200) (3200) (6350) (7050) (8250) (8250)
3.0 m 1500* 1500* 4100* 3100 4900* 4900* 6950* 6950*
(10') (3300) (3300) (9000) (6800) (10750) (10750) (15300) (15300)
1.5 m 1550* 1550* 4350 3000 6200* 4750 6550* 6550*
(5') (3400) (3400) (9550) (6600) (13650) (10450) (14400) (14400)
0.0 m 1750* 1750* 4250 2900 6900 4550 5550* 5550*
(0') (3850) (3850) (9350) (6350) (15150) (10000) (12200) (12200)
–1.5 m 2150* 2150* 4200 2850 6800 4500 8050* 8050* 3850* 3850*
(–5') (4700) (4700) (9250) (6250) (14950) (9900) (17700) (17700) (8450) (8450)
–3.0 m 2950* 2800 4250 2900 6500* 4500 9700* 9100 7050* 7050*
(–10') (6500) (6150) (9430) (6350) (14300) (9900) (21350) (20000) (15500) (15500)
Blade above ground Arm length 3000 mm (9'10")
7.5 m 1900* 1900*
(25') (4150) (4150)
6.0 m 1550* 1550* 2900* 2050
(20') (3400) (3400) (6350) (4500)
4.5 m 1450* 1300 3600* 2000 3750* 3350
(15') (3200) (2850) (7900) (4400) (8250) (7350)
3.0 m 1500* 1150 3700 1950 4900* 3150 6950* 6100
(10') (3300) (2500) (8150) (4300) (10750) (6900) (15300) (13400)
1.5 m 1550* 1100 3600 1850 5850 2950 6550* 5400
(5') (3400) (2400) (7900) (4050) (12850) (6500) (14400) (11850)
0.0 m 1750* 1150 3500 1750 5650 2750 5550* 5100
(0') (3850) (2500) (7700) (3850) (12400) (6050) (12200) (11200)
–1.5 m 2150* 1300 3450 1700 5550 2700 8050* 5050 3850* 3850*
(–5') (4700) (2850) (7600) (3750) (12200) (5950) (17700) (11100) (8450) (8450)
–3.0 m 2950* 1700 3500 1750 5600 2700 9700* 5150 7050* 7050*
(–10') (6500) (3750) (7700) (3850) (12300) (5950) (21350) (11300) (15500) (15500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-28
AH_25.book Page 29 Tuesday, March 23, 2004 9:41 AM
Conditions:
Boom: 4800 mm (15'9"), Bucket (SAE): 0.62 m3 (0.81 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Blade and rear outrigger on ground Arm length 2600 mm (8'6")
7.5 m 1850* 1850*
(25') (4050) (4050)
6.0 m 1550* 1550 2850* 2850*
(20') (3400) (3400) (6250) (6250)
4.5 m 1400* 1400* 3400* 3400* 3600* 3600*
(15') (3050) (3050) (7450) (7450) (7900) (7900)
3.0 m 1400* 1400* 3850* 3850* 4650* 4650* 6700* 6700*
(10') (3050) (3050) (8450) (8450) (10200) (10200) (14750) (14750)
1.5 m 1500* 1500* 4400* 4250 5850* 5850* 6600* 6600*
(5') (3300) (3300) (9650) (9350) (12850) (12850) (14500) (14500)
0.0 m 1700* 1700* 4800* 4800* 6650* 6650* 5650* 5650*
(0') (3750) (3750) (10550) (10550) (14600) (14600) (12400) (12400)
–1.5 m 2050* 2050* 4800* 4050 6750* 6650 8200* 8200* 3950* 3950*
(–5') (4500) (4500) (10550) (8900) (14850) (14600) (18050) (18050) (8700) (8700)
–3.0 m 2850* 2850* 3700* 3700* 6050* 6050* 9050* 9050*
(–10') (6250) (6250) (8150) (8150) (13300) (13300) (19900) (19900)
Front and rear outrigger above ground Arm length 2600 mm (8'6")
7.5 m 1850* 1850*
(25') (4050) (4300)
6.0 m 1550* 1550* 2850* 2850*
(20') (3400) (3400) (6250) (6250)
4.5 m 1400* 1400* 3400* 3400* 3600* 3600*
(15') (3050) (3050) (7450) (7450) (7900) (7900)
3.0 m 1400* 1400* 3850* 3550 4650* 4650* 6700* 6700*
(10') (3050) (3050) (8450) (7800) (10200) (10200) (14750) (14750)
1.5 m 1500* 1500* 4400* 3400 5500 5850* 6600* 6600*
(5') (3300) (3300) (9650) (7450) (12100) (12850) (14500) (14500)
0.0 m 1700* 1700* 4800* 3300 5250 6650* 5650* 5650*
(0') (3750) (3750) (10550) (7250) (11550) (14600) (12400) (12400)
–1.5 m 2050* 2050* 4800* 3250 5150 6550 8200* 8200* 3950* 3950*
(–5') (4500) (4500) (10550) (7150) (11300) (14400) (18050) (18050) (8700) (8700)
–3.0 m 2850* 2850* 3700* 3300 5200 6050* 9050* 9050*
(–10') (6250) (6250) (8150) (7250) (11450) (13300) (19900) (19900)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-29
AH_25.book Page 30 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5200 mm (17'1"), Bucket(SAE): 0.76 m3 (0.99 cu.yd), Tires:10.00-20-16PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Rear outrigger on ground Arm length 1800 mm (5'11")
7.5 m 4300* 4300*
(25') (9400) (9400)
6.0 m 3650* 3650*
(20') (8000) (8000)
4.5 m 3450* 3450* 4350* 4350* 5000* 5000*
(15') (7600) (7600) (9600) (9600) (11000) (11000)
3.0 m 3500* 3450 4750* 4750* 6100* 6100*
(10') (7700) (7600) (10400) (10400) (13400) (13400)
1.5 m 3750* 3300 5250* 4600 7150* 7150*
(5') (8200) (7200) (11500) (10100) (15700) (15700)
0.0 m 4250 3400 5500* 4500 7600* 7200
(0') (9300) (7500) (12100) (9900) (16700) (15800)
–1.5 m 4550* 3850 5300* 4450 7350* 7150 9450* 9450*
(–5') (10000) (8500) (11600) (9800) (16200) (15700) (20800) (20800)
–3.0 m 4450* 4450* 6200* 6200* 8700* 8700*
(–10') (9800) (9800) (13600) (13600) (19100) (19100)
Blade above ground Arm length 1800 mm (5'11")
7.5 m 4300* 4300*
(25') (9400) (9400)
6.0 m 3650* 2700
(20') (8000) (5900)
4.5 m 3450* 2050 4350* 2650 5000* 4400
(15') (7600) (4500) (9600) (5800) (11000) (9700)
3.0 m 3500* 1750 4750* 2500 6100* 4000
(10') (7700) (5800) (10400) (5500) (13400) (8800)
1.5 m 3750* 1650 5250* 2350 7150* 3650
(5') (8200) (3600) (11500) (5200) (15700) (8000)
0.0 m 4050 1700 5400 2250 7800* 3450
(0') (8900) (3700) (11900) (4900) (17100) (7600)
–1.5 m 4550* 1950 5300* 2250 7350* 3400 9450* 6550
(–5') (10000) (4300) (11600) (4900) (16200) (7500) (20800) (14400)
–3.0 m 4450 2550 6200* 3550 8700* 6800
(–10') (9800) (5600) (13600) (7800) (19100) (14900)
Front outrigger on ground and rear blade above ground Arm length 1800 mm (5'11")
7.5 m 4300* 4300*
(25') (9400) (9400)
6.0 m 3650* 3650*
(20') (8000) (8000)
4.5 m 3450* 3200 4350* 4050* 5000* 5000*
(15') (7600) (7000) (9600) (8900) (11000) (11000)
3.0 m 3500* 2800 4750* 3900 6100* 6100*
(10') (7700) (6100) (10400) (8600) (13400) (13400)
1.5 m 3750* 2650 5250* 3750 7150* 5850
(5') (8200) (5800) (11500) (8200) (15700) (12900)
0.0 m 4250* 2750 5500* 3600 7600* 5650
(0') (9300) (6000) (12100) (7900) (16700) (12400)
–1.5 m 4550* 3100 5300* 3600 7350* 5600 9450* 9450*
(–5') (10000) (6800) (11600) (7900) (16200) (12300) (20800) (20800)
–3.0 m 4450* 4050 6200* 5700 8700* 8700*
(–10') (9800) (8900) (13600) (12500) (19100) (19100)
Front and rear outrigger on ground Arm length 1800 mm (5'11")
7.5 m 4300* 4300*
(25') (9400) (9400)
6.0 m 3650* 3650*
(20') (8000) (8000)
4.5 m 3450* 3450* 4350* 4350* 5000* 5000*
(15') (7600) (7600) (9600) (9600) (11000) (11000)
3.0 m 3500* 3500* 4750* 4750* 6100* 6100*
(10') (7700) (7700) (10400) (10400) (13400) (13400)
1.5 m 3750* 3450 5250* 4850 7150* 7150*
(5') (8200) (7600) (11500) (10700) (15700) (15700)
0.0 m 4250* 3600* 5500* 4750 7600* 7600*
(0') (9300) (7900) (12100) (10400) (16700) (16700)
–1.5 m 4550* 4050 5300* 4700 7350* 7350* 9450* 9450*
(–5') (10000) (8900) (11600) (10300) (16200) (16200) (20800) (20800)
–3.0 m 4450* 4450* 8200* 8200* 8700* 8700*
(–10') (9800) (9800) (18000) (18000) (19100) (19100)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-30
AH_25.book Page 31 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5200 mm (17'11"), Bucket(SAE): 0.76 m3 (0.99 cu.yd), Tires: 10.00-20-16PR unit: kg (lb)
A MAX 6.0 m (20') 4.5 m (15') 3.0 m (10') 1.5 m (5')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Rear outrigger on ground Arm length 1800 mm (5'11")
7.5 m 4250* 4250* 4850* 4850*
(25') (9300) (9300) (10700) (10700)
6.0 m 3550* 3550* 4700* 4700* 4600* 4600*
(20') (7800) (7800) (10300) (10300) (10100) (10100)
4.5 m 3350* 3350* 4950* 4950* 5500* 5500*
(15') (7400) (7400) (10900) (10900) (12100) (12100)
3.0 m 3300* 3300* 5450* 4800 7050* 7050*
(10') (7300) (7300) (12000) (10600) (15500) (15500)
1.5 m 3500* 3250 5800 4650 8550* 7450
(5') (7700) (7100) (12800) (10200) (18800) (16400)
0.0 m 3850* 3400 5700 4550 9400* 7300
(0') (8500) (7500) (12500) (10000) (20700) (16100)
–1.5 m 4600* 3900 5700 4500 9450* 7250 9050* 9050*
(–5') (10100) (8600) (12500) (9900) (20800) (15900) (19900) (19900)
–3.0 m
(–10')
Blade above ground Arm length 1800 mm (5'11")
7.5 m 4250* 3850 4850* 4450
(25') (9300) (8500 (10700) (9800)
6.0 m 3550* 2450* 4700* 2650 4600* 4500
(20') (7800) (5400) (10300) (5800) (10100) (9900)
4.5 m 3350* 1950 4950* 2600 5500* 4300
(15') (9400) (4300) (10900) (5700) (12100) (9500)
3.0 m 3300* 1700 5450* 2500 7050* 3950
(10') (7300) (3700) (12000) (5500) (15500) (8700)
1.5 m 3500* 1650 5550 2350 8550* 3650
(5') (7700) (3600) (12200) (5200) (18800) (8000)
0.0 m 3850* 1700 5450 2300 9050 3500
(0') (8500) (3700) (12200) (5100) (19900) (7700)
–1.5 m 4600* 1950 5450 2250 9050 3500 9050* 6750
(–5') (10100) (4300) (12200) (4900) (19900) (7700) (19900) (14800)
–3.0 m
(–10')
Front outrigger on ground and rear blade above ground Arm length 1800 mm (5'11")
7.5 m 4250* 4250* 4850* 4850*
(25') (9300) (9300) (10700) (10700)
6.0 m 3550* 3550* 4700* 4050 4600* 4600*
(20') (7800) (7800) (10300) (8900) (10100) (10100)
4.5 m 3350* 3050* 4950* 4000 5500* 5500*
(15') (7400) (6700) (10900) (8800) (12100) (12100)
3.0 m 3300* 2700* 5450* 3900 7050* 6250
(10') (7300) (5900) (12000) (8600) (15500) (13700)
1.5 m 3500* 2600* 5950* 3750 8550* 5850
(5') (7700) (5700) (13100) (8200) (18800) (12900)
0.0 m 3850* 2750 6550* 3650 9400* 5700
(0') (8500) (6000) (14400) (8000) (20700) (12500)
–1.5 m 4600* 3150 6850* 3650 9450* 5700 9050* 9050*
(–5') (10100) (6900) (15100) (8000) (20800) (12500) (19900) (19900)
–3.0 m 8750* 5700
(–10') (19200) (12500)
Front and rear outrigger on ground Arm length 1800 mm (5'11")
7.5 m 4250* 4250* 4850* 4850*
(25') (9300) (9300) (10700) (10700)
6.0 m 3550* 3550* 4700* 4700* 4600* 4600*
(20') (7800) (7800) (10300) (10300) (10100) (10100)
4.5 m 3350* 3350* 4950* 4950* 5500* 5500*
(15') (7400) (7400) (10900) (10900) (12100) (12100)
3.0 m 3300* 3300* 5450* 5050 7050* 7050*
(10') (7300) (7300) (12000) (11100) (15500) (15500)
1.5 m 3500* 3400 5950* 4900 8550* 7850
(5') (7700) (7500) (13100) (10800) (18800) (17300)
0.0 m 3850* 3600 6550* 4800 9400* 7650
(0') (8500) (7900) (14400) (10600) (20700) (16800)
–1.5 m 2800* 2800 6850* 4800 9450* 7650 9050* 9050*
(–5') (6200) (6200) (15100) (10500) (20800) (16800) (19900) (19900)
–3.0 m
(–10')
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-31
AH_25.book Page 32 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5200 mm (17'1"), Bucket (SAE): 0.76 m3 (0.99 cu.yd), Tires:10.00-20-16PR unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Front outrigger on ground and rear blade above ground Arm length 2250 mm (7'5")
7.5 m 2400* 2400*
(25') (5300) (5300)
6.0 m 2100* 2100* 3200* 3200*
(20') (4600) (4600) (7000) (7000)
4.5 m 2050* 2050* 4000* 4000* 4500* 4500*
(15') (4500) (4500) (8800) (8800) (9900) (9900)
3.0 m 2100* 2100* 2550* 2550* 4450* 3900 5650* 5650* 8750* 8750*
(10') (4600) (4600) (5610) (5610) (9800) (8600) (12400) (12400) (19200) (19200)
1.5 m 2300* 2300* 3500* 2550* 5000* 3700 6800* 5850
(5') (5100) (5100) (7700) (5600) (11000) (8100) (15000) (12900)
0.0 m 2650* 2500 2700* 2500 5350* 3550 7450* 5600 5700* 5700*
(0') (5800) (5500) (5900) (5500) (11800) (7800) (16400) (12300) (12500) (12500)
–1.5 m 3250* 2750 5300* 3500 7400* 5500 9350* 9350*
(–5') (7100) (6050) (11700) (7700) (16300) (12100) (20600) (20600)
–3.0 m 4350* 3500 4450* 3550 6550* 5550 9400* 9400*
(–10') (9600) (7700) (9800) (7800) (14400) (12200) (20700) (20700)
Front and rear outrigger on ground Arm length 2250 mm (7'5")
7.5 m 2400* 2400*
(25') (5300) (5300)
6.0 m 2100* 2100* 3200* 3200*
(20') (4600) (4600) (7000) (7000)
4.5 m 2050* 2050* 4000* 4000* 4500* 4500*
(15') (4500) (4500) (8800) (8800) (9900) (9900)
3.0 m 2100* 2100* 2550* 2550* 4450* 4450* 5650* 5650* 8750* 8750*
(10') (4600) (4600) (5610) (5610) (9800) (9800) (12400) (12400) (19200) (19200)
1.5 m 2300* 2300* 3500* 3300 5000* 4850 6800* 6800
(5') (5100) (5100) (7700) (7300) (11000) (10700) (15000) (15000)
0.0 m 2650* 2650* 2700* 2700* 5350* 4700 7450* 7450* 5700* 5700*
(0') (5800) (5800) (5900) (5900) (11800) (10300) (16400) (16400) (12500) (12500)
–1.5 m 3250* 3250* 5300* 4600 7400* 7400* 9350* 9350*
(–5') (7100) (7100) (11700) (10100) (16300) (16300) (20600) (20600)
–3.0 m 4350* 4350* 4450* 4450* 6550* 6550* 9400* 9400*
(–10') (9600) (9600) (9800) (9800) (14400) (14400) (20700) (20700)
Rear outrigger on ground Arm length 2250 mm (7'5")
7.5 m 2400* 2400*
(25') (5300) (5300)
6.0 m 2100* 2100* 3200* 3200*
(20') (4600) (4600) (7040) (7040)
4.5 m 2050* 2050* 4000* 4000* 4500* 4500*
(15') (4500) (4500) (8800) (8800) (9900) (9900)
3.0 m 2100* 2100* 2550* 2550* 4450* 4450* 5650* 5650* 8750* 8750*
(10') (4600) (4600) (5600) (5600) (9800) (9800) (12400) (12400) (19200) (19200)
1.5 m 2300* 2300* 3500* 3150 5100* 4800 6800* 6800*
(5') (5100) (5100) (7700) (6900) (11200) (10600) (15000) (15000)
0.0 m 2650* 2650* 2700* 2700* 5350* 4450 7450* 7150 5700* 5700*
(0') (5800) (5800) (5900) (5900) (11800) (9800) (16400) (15700) (12500) (12500)
–1.5 m 3250* 3250* 5300* 4350 7400* 7050 9350* 9350*
(–5') (7100) (7100) (11700) (9600) (16300) (15500) (20800) (20800)
–3.0 m 4350* 4350* 4450* 4450 6550* 6550* 9400* 9400*
(–10') (9600) (9600) (9800) (9800) (14400) (14400) (20700) (20700)
Blade above ground Arm length 2250 mm (7'5")
7.5 m 2400* 2400*
(25') (5300) (5300)
6.0 m 2100* 2100* 3200* 2700
(20') (4600) (4600) (7040) (5900)
4.5 m 2050* 1850 4000* 2650 4500* 4450
(15') (4500) (4100) (8800) (5830) (9900) (9800)
3.0 m 2100* 1550 2550* 1600 4450* 2500 5650* 4050 8750* 7750
(10') (4600) (3400) (5600) (3500) (9800) (5500) (12400) (8900) (19200) (17000)
1.5 m 2300* 1450 3500* 1550 5000* 2300 6800* 3650
(5') (5100) (3200) (7700) (3400) (11000) (5100) (15000) (8000)
0.0 m 2650* 1500 2700* 1500 5350 2200 7450* 3400 5700* 5700*
(0') (5800) (3300) (5900) (3300) (11800) (4800) (16400) (7500) (12500) (12500)
–1.5 m 3250* 1700 5300 2150 7400* 3350 9350* 6400
(–5') (7100) (3700) (11700) (4700) (16300) (7400) (20800) (14100)
–3.0 m 4350* 2150 4450* 2200 6550* 3400 9400* 6600
(–10') (9600) (4700) (9800) (4800) (14400) (7500) (20700) (14500)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-32
AH_25.book Page 33 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5200 mm (17'1"), Bucket (SAE): 0.76 m3 (0.99 cu.yd), Tires: 10.00-20-16PR unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Rear outrigger on ground Arm length 2250 mm (7'5")
7.5 m 2300* 2300*
(25') (5100) (5100)
6.0 m 1950* 1950* 3800* 3800*
(20') (4300) (4300) (8400) (8400)
4.5 m 1900* 1900* 4500* 4500* 4950* 4950*
(15') (4200) (4200) (9900) (9900) (10900) (10900)
3.0 m 1900 1900* 3250* 3200 5200* 4750 6500* 6500*
(10') (4200) (4200) (7100) (7000) (11400) (10400) (14300) (14300)
1.5 m 2050* 2050* 3950 3150 5700* 4600 8100* 7450
(5') (4500) (4500) (8700) (6900) (12500) (10100) (17800) (16400)
0.0 m 2300* 2300* 3050* 3050* 5650 4450 9100 7200 5150* 5150*
(0') (5100) (5100) (6700) (6700) (12400) (9800) (20000) (15800) (11300) (11300)
–1.5 m 2800* 2800* 5600 4450 9350 7150 9100* 9100*
(–5') (6200) (6200) (12300) (9800) (20600) (15700) (20000) (20000)
–3.0 m 8750* 7250
(–10') (19200) (15900)
Blade above ground Arm length 2250 mm (7'5")
7.5 m 2300* 2300*
(25') (5100) (5100)
6.0 m 1950* 1950* 3800* 2650
(20') (4300) (4300) (8400) (5800)
4.5 m 1900* 1700 4500* 2800 4950* 4350
(15') (4200) (3700) (9900) (6200) (10900) (9600)
3.0 m 1900 1500 3250* 1600 5200* 2450 6500* 4000
(10') (4200) (3300) (7100) (3500) (11400) (5400) (14300) (8800)
1.5 m 2050* 1450 3750 1550 5550 2300 8100* 3650
(5') (4500) (3200) (8700) (3400) (12200) (5100) (17800) (8000)
0.0 m 2300* 1500 3050* 1500 5400 2200 9000 3450 5150* 5150*
(0') (5100) (3300) (6700) (3300) (11900) (4800) (19800) (7600) (11300) (11300)
–1.5 m 2800* 1700 5350 2200 8950 3400 9100* 6550
(–5') (6200) (3700) (11800) (4800) (19700) (7500) (20000) (14400)
–3.0 m 8750* 3500
(–10') (19200) (7700)
Front outrigger on ground and rear blade above ground Arm length 2250 mm (7'5")
7.5 m 2300* 2300*
(25') (5100) (5100)
6.0 m 1950* 1950* 3800* 3800*
(20') (4300) (4300) (8400) (8400)
4.5 m 1900* 1900* 4500* 4500* 4950* 4950*
(15') (4200) (4200) (9900) (9900) (10900) (10900)
3.0 m 1900* 1900* 3250* 2600 5200* 3850 6500* 6250
(10') (4200) (4200) (7100) (5700) (11400) (8500) (14300) (13700)
1.5 m 2050* 2050* 4050* 2550 5700* 3700 8100* 5850
(5') (4500) (4500) (8900) (5600) (12500) (8100) (17800) (12900)
0.0 m 2300* 2300* 3050* 2500 6250* 3550 9100* 5650 5150* 5150*
(0') (5100) (5100) (6700) (5500) (13700) (7800) (20000) (12400) (11300) (11300)
–1.5 m 2800* 2800 6800* 3550 9400* 5600 9100* 9100*
(–5') (6200) (6200) (15000) (7800) (20700) (12300) (20000) (20000)
–3.0 m 8750* 5700
(–10') (19200) (12500)
Front and rear outrigger on ground Arm length 2250 mm (7'5")
7.5 m 2300* 2300*
(25') (5100) (5100)
6.0 m 1950* 1950* 3800* 3800*
(20') (4300) (4300) (8400) (8400)
4.5 m 1900* 1900* 4500* 4500* 4950* 4950*
(15') (4200) (4200) (9900) (9900) (10900) (10900)
3.0 m 1900* 1900* 3250* 3250* 5200* 5000 6500* 6500
(10') (4200) (4200) (7100) (7100) (11400) (11000) (14300) (14300)
1.5 m 2050* 2050* 4050* 3350 5700* 4850 8100* 7850
(5') (4500) (4500) (8900) (7370) (12500) (10700) (17800) (17300)
0.0 m 2300* 2300* 3050* 3050* 6250* 4700 9100* 7850 5150* 5150*
(0') (5100) (5100) (6700) (6700) (13700) (10300) (20000) (17300) (11300) (11300)
–1.5 m 2800* 2800 6800* 4700 9400* 7550 9100* 9100*
(–5') (6200) (6200) (15000) (10300) (20700) (16600) (20000) (20000)
–3.0 m 8750* 7850
(–10') (19200) (17300)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-33
AH_25.book Page 34 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5200 mm (17'1"), Bucket (SAE): 0.76 m3 (0.99 cu.yd), Tires:10.00-20-16PR unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Rear outrigger on ground Arm length 2600 mm (8'6")
7.5 m 1900* 1900*
(25') (4200) (4200)
6.0 m 1700* 1700* 3150* 3150*
(20') (3700) (3700) (6900) (6900)
4.5 m 1650* 1650* 3700* 3700*
(15') (3600) (3600) (8100) (8100)
3.0 m 1700* 1700* 3100* 3100* 4250* 4250* 5300* 5300* 7750* 7750*
(10') (3700) (3700) (6800) (6800) (9300) (9300) (11700) (11700) (17000) (17000)
1.5 m 1900* 1900* 3950* 3150 4850* 4600 6450* 6450* 6750* 6750*
(5') (4200) (4200) (8700) (6900) (10700) (10100) (14200) (14200) (14800) (14800)
0.0 m 2200* 2200* 3850 3050 5250* 4450 7300* 7200 6400* 6400*
(0') (4800) (4800) (8500) (6700) (11500) (9800) (16100) (15800) (14100) (14100)
–1.5 m 2750* 2750* 5350* 4350 7450* 7050 9100* 9100*
(–5') (6000) (6000) (11800) (9600) (16400) (15500) (20000) (20000)
–3.0 m 3900* 3900* 4800* 4400 6800* 6800* 9950* 9950*
(–10') (8600) (8600) (10600) (9700) (15000) (15000) (21900) (21900)
Blade above ground Arm length 2600 mm (8'6")
7.5 m 1900* 1900*
(25') (4200) (4200)
6.0 m 1700* 1700* 3150* 2700
(20') (3700) (3700) (6900) (5900)
4.5 m 1650* 1650* 3700* 2650
(15') (3600) (3600) (8100) (5800)
3.0 m 1700* 1450 3100* 1600 4250* 2500 5300* 4150 7750* 7750*
(10') (3700) (3200) (6800) (3500) (9300) (5500) (11700) (9100) (17000) (17000)
1.5 m 1900* 1350 3750 1550 4850* 2350 6450* 3650 6750* 6750*
(5') (4200) (3000) (8200) (3400) (10700) (5200) (14200) (8000) (14800) (14800)
0.0 m 2200* 1400 3700 1500 5250* 2200 7300* 3450 6400* 6400*
(0') (4800) (3100) (8100) (3300) (11500) (4800) (16100) (7600) (14100) (14100)
–1.5 m 2750* 1550 5250 2100 7450* 3300 9100* 6350
(–5') (6000) (3400) (11500) (4600) (16400) (7300) (20000) (14000)
–3.0 m 3900* 1950 4800* 2150 6800* 3350 9500* 6500
(–10') (8600) (4300) (10600) (4700) (15000) (7400) (21000) (14300)
Front outrigger on ground and rear blade above ground Arm length 2600 mm (8'6")
7.5 m 1900* 1900*
(25') (4200) (4200)
6.0 m 1700* 1700* 3150* 3150*
(20') (3700) (3700) (6900) (6900)
4.5 m 1650* 1650* 3700* 3700*
(15') (3600) (3600) (8100) (8100)
3.0 m 1700* 1700* 3100* 2600 4250* 3900 5300* 5300* 7750* 7750*
(10') (3700) (3700) (6800) (5700) (9300) (8600) (11700) (11700) (17000) (17000)
1.5 m 1900* 1900* 3950* 2550 4850* 3700 6450* 5850 6750* 6750*
(5') (4200) (4200) (8700) (5600) (10700) (8100) (14200) (12900) (14800) (14800)
0.0 m 2200* 2200* 3900* 2450 5250* 3550 7300* 5600 6400* 6400*
(0') (4800) (4800) (8600) (5400) (11500) (7800) (16100) (12300) (14100) (14100)
–1.5 m 2750* 2550 5350* 3450 7450* 5500 9100* 9100*
(–5') (6000) (5600) (11800) (7600) (16400) (12100) (20000) (20000)
–3.0 m 3900* 3150 4800* 3500 6800* 5500 9950* 9950*
(–10') (8600) (6900) (10600) (7700) (15000) (12100) (21900) (21900)
Front and rear outrigger on ground Arm length 2600 mm (8'6")
7.5 m 1900* 1900*
(25') (4200) (4200)
6.0 m 1700* 1700* 3150* 3150*
(20') (3700) (3700) (6900) (6900)
4.5 m 1650* 1650* 3700* 3700*
(15') (3600) (3600) (8100) (8100)
3.0 m 1700* 1700* 3100* 3100* 4250* 4250* 5300* 5300* 7750* 7750*
(10') (3700) (3700) (6800) (6800) (9350) (9350) (11700) (11700) (17000) (17000)
1.5 m 1900* 1900* 3950* 3300 4850* 4850* 6450* 6450* 6750* 6750*
(5') (4200) (4200) (8700) (7300) (10700) (10700) (14200) (14200) (14800) (14800)
0.0 m 2200* 2200* 3900* 3250 5250* 4700 7300* 7300* 6400* 6400*
(0') (4800) (4800) (8600) (7100) (11500) (10300) (16100) (16100) (14100) (14100)
–1.5 m 2750* 2750* 5350* 4600 7450* 7450* 9100* 9100*
(–5') (6000) (6000) (11800) (10100) (16400) (16400) (20000) (20000)
–3.0 m 3900* 3900* 4850* 4650 6800* 6800* 9500* 9500*
(–10') (8600) (8600) (10700) (10200) (15000) (15000) (21900) (21900)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-34
AH_25.book Page 35 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5200 mm (17'1"), Bucket (SAE): 0.76 m3 (0.99 cu.yd), Tires: 10.00-20-16PR unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Front outrigger on ground and rear blade above ground Arm length 2600 mm (8'6")
7.5 m 1800* 1800*
(25') (4000) (4000)
6.0 m 1550* 1550* 3500* 3500*
(20') (3400) (3400) (7700) (7700)
4.5 m 1500* 1500* 2250* 2250* 4150* 4050 4450* 4450*
(15') (3300) (3300) (4900) (4900) (9100) (8900) (9800) (9800)
3.0 m 1550* 1550* 3500* 2600 4900* 3900 6000* 6000 9100* 9100*
(10') (3400) (3400) (7700) (5700) (10800) (8600) (13200) (13200) (20000) (20000)
1.5 m 1650* 1650* 4250* 2550 5500* 3700 7700* 5900
(5') (3600) (3600) (9300) (5600) (12100) (8100) (16900) (13000)
0.0 m 1900* 1900* 4250* 2540 6100* 3550 8900* 5650
(0') (4200) (4200) (9300) (5600) (13400) (7800) (19600) (12400)
–1.5 m 2350* 2350* 6650* 3500 9350* 5550 8800* 8800*
(–5') (5200) (5200) (14600) (7700) (20600) (12200) (19400) (19400)
–3.0 m 6400* 3550 9000* 5600 13450* 11850
(–10') (14100) (7800) (19800) (12300) (29600) (26100)
Front and rear outrigger on ground Arm length 2600 mm (8'6")
7.5 m 1800* 1800*
(25') (4000) (4000)
6.0 m 1550* 1550* 3500* 3500*
(20') (3400) (3400) (7700) (7700)
4.5 m 1500* 1500* 2250* 2250* 4150* 4150* 4450* 4450*
(15') (3300) (3300) (4900) (4900) (9100) (9100) (9800) (9800)
3.0 m 1550* 1550* 3500* 3400 4900* 4900* 6000* 6000* 9100* 9100*
(10') (3400) (3400) (7700) (7500) (10800) (10800) (13200) (13200) (20000) (20000)
1.5 m 1850* 1850* 4250* 3300 5500* 4850 7700* 7700*
(5') (4100) (4100) (9300) (7300) (12100) (10700) (16900) (16900)
0.0 m 1900* 1900* 4250* 3250 6100* 4700 8900* 7600 5750* 5750*
(0') (4200) (4200) (9300) (7100) (13400) (10300) (19600) (16700) (12600) (12600)
–1.5 m 2350* 2350* 6650* 4650 9350* 7500 8800* 8800*
(–5') (5200) (5200) (14600) (10200) (20600) (16500) (19400) (19400)
–3.0 m 6400* 4700 9000* 7600 13450* 13450*
(–10') (14100) (10300) (19800) (16700) (29600) (29600)
Rear outrigger on ground Arm length 2600 mm (8'6")
7.5 m 1800* 1800*
(25') (4000) (4000)
6.0 m 1550* 1550* 3500* 3500*
(20') (3400) (3400) (7700) (7700)
4.5 m 1500* 1500* 2250* 2250* 4150* 4150* 4450* 4450*
(15') (3300) (3300) (4900) (4900) (9100) (9100) (9800) (9800)
3.0 m 1550* 1550* 3500* 3200 4900* 4800 6800* 6000 9100* 9100*
(10') (3400) (3400) (7700) (7040) (10800) (10600) (15000) (13200) (20000) (20000)
1.5 m 1650* 1650* 3950 3150 5500* 4600 7700* 7500
(5') (3600) (3600) (8700) (6900) (12100) (10100) (16900) (16500)
0.0 m 1900* 1900* 3900 3100 3650 4450 8900* 7200 5750* 5750*
(0') (4200) (4200) (8600) (6800) (8000) (9800) (19600) (15800) (12600) (12600)
–1.5 m 2350* 2350* 5550 4400 9300 7100 8800* 8800*
(–5') (5200) (5200) (12200) (9700) (20500) (15600) (19400) (19400)
–3.0 m 5650 4450 9000* 7200 13450* 13450*
(–10') (12400) (9800) (19800) (15800) (29600) (29600)
Blade above ground Arm length 2600 mm (8'6")
7.5 m 1800* 1800*
(25') (4000) (4000)
6.0 m 1550* 1550* 3500* 2700
(20') (3400) (3400) (7700) (5900)
4.5 m 1500* 1500* 2250* 1650 4150* 2650 4450* 4400
(15') (3300) (3300) (4900) (3600) (9100) (5800) (9800) (9700)
3.0 m 1550* 1350 3500* 1600 4900* 2500 6000* 4050 9100* 7850
(10') (3400) (3000) (7700) (3500) (10800) (5500) (13200) (8900) (20000) (17300)
1.5 m 1650* 1300 3750 1550 5500* 2300 7700* 3650
(5') (3600) (2900) (8200) (3400) (12100) (5000) (16900) (8000)
0.0 m 1900* 1350 3700 1500 5400 2200 8900* 3450 5750* 5750*
(0') (4200) (3000) (8100) (3300) (11900) (4800) (19600) (7600) (12600) (12600)
–1.5 m 2350* 1550 5300 2150 8900 3350 8800* 6500
(–5') (5200) (3400) (11700) (4700) (19600) (7400) (19400) (14300)
–3.0 m 5400 2200 8950 3400 13450* 6700
(–10') (11900) (4800) (19700) (7500) (29600) (14700)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-35
AH_25.book Page 36 Tuesday, March 23, 2004 9:41 AM
Conditions:Boom: 5200 mm (17'1"), Bucket (SAE): 0.76 m3 (0.99 cu.yd), Tires: 10.00-20-16PR unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Front outrigger on ground and rear blade above ground with rotating arm
7.5 m 1350* 1350*
(25') (3000) (3000)
6.0 m 1200* 1200* 2800* 2800*
(20') (2600) (2600) (6200) (6200)
4.5 m 1150* 1150* 1650* 1650* 3600* 3600*
(15') (2500) (2500) (3600) (3600) (7900) (7900)
3.0 m 1200* 1200* 2750* 2350 4300* 3600 5200* 5200* 7650* 7650*
(10') (2600) (2600) (6000) (5200) (9500) (7900) (11400) (11400) (16800) (16800)
1.5 m 1350* 1350* 3450* 2250 4950* 3300 6850* 5400 9100* 9100*
(5') (3000) (3000) (7600) (4900) (10900) (7300) (15100) (11900) (20000) (20000)
0.0 m 1600* 1600* 3400* 2150 5450* 3100 8050* 5000 7800* 7800*
(0') (3500) (3500) (7500) (4700) (12000) (6800) (17800) (11000) (17200) (17200)
–1.5 m 2100* 2100* 6000* 3050 8650* 4850 9950* 9950*
(–5') (4600) (4600) (13200) (6700) (19000) (10700) (21900) (21900)
–3.0 m 3250* 2800 6650* 3100 8450* 4950 12850* 10650*
(–10') (7100) (6200) (14600) (6800) (18600) (10900) (28300) (23400)
Front and rear outrigger on ground with rotating arm
7.5 m 1350* 1350*
(25') (3000) (3000)
6.0 m 1200* 1200* 2800* 2800*
(20') (2600) (2600) (6200) (6200)
4.5 m 1150* 1150* 1650* 1650* 3600* 3600*
(15') (2500) (2500) (3600) (3600) (7900) (7900)
3.0 m 1200* 1200* 2750* 2750* 4300* 4300* 5200* 5200* 7650* 7650*
(10') (2600) (2600) (6000) (6000) (9500) (9500) (11400) (11400) (16800) (16800)
1.5 m 1350* 1350* 3450* 3050 4950* 4450 6850* 6850* 9100* 9100*
(5') (3000) (3000) (7600) (6700) (10900) (9800) (15100) (15100) (20000) (20000)
0.0 m 1600* 1600* 3400* 2950 5450* 4250 8050* 6950 7800* 7800*
(0') (3500) (3500) (7500) (6500) (12000) (9300) (17800) (15300) (17200) (17200)
–1.5 m 2100* 2100* 6000* 4150 8650* 6800 9950* 9950*
(–5') (4600) (4600) (13200) (9100) (19000) (15000) (21900) (21900)
–3.0 m 3250* 3250* 6050* 4250 8450 8900 12850* 12850*
(–10') (7100) (7100) (13300) (9300) (18600) (19600) (28300) (28300)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-36
AH_25.book Page 37 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 0.80 m3, Tires:10.00-20-14PR unit: kg
A MAX 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 1800 mm
7.5 m *4800 3900
6.0 m *4450 2600 *7450 3300
4.5 m *4450 2050 *4450 2020 7750 3200 *10150 5200 *15600 9950
3.0 m *4550 1800 5000 2000 7450 2950 *11400 4600
1.5 m *4400 1700 4900 1900 7100 2700 *11500 4100
0.0 m *4550 1750 4850 1850 6850 2500 *10350 3950
–1.5 m *4750 1950 4850 1850 *6500 2500 *8450 3950 *8400 7700
–3.0 m *3600 2550 *4100 2700 *5700 4150
Rear outrigger on ground Arm length 1800 mm
7.5 m *4800 4450
6.0 m *4450 3000 *7450 3850
4.5 m *4400 2400 *4450 2400 *7850 3700 *10150 6000 *15600 11800
3.0 m *4650 2150 5600 2350 *8250 3450 *11400 5400
1.5 m *4950 2000 5500 2250 8050 3200 *11500 4900
0.0 m *5100 2100 5400 2200 *7750 3000 *10350 4700
–1.5 m *4750 2350 *6500 3000 *8450 4750 *8400 *8400
–3.0 m *3600 3000 *4100 3200 *5700 4900
Front outrigger on ground and rear blade on ground Arm length 1800 mm
7.5 m *4850 *4850
6.0 m *4500 4000 *7600 5050
4.5 m *4500 3250 *4500 3250 7800 4900 *10300 8000 *15800 *15800
3.0 m 4700 2900 5150 3200 7550 4650 *11550 7300
1.5 m 4550 2800 5050 3100 7200 4350 *11700 6750
0.0 m 4700 2850 4950 3050 6950 4150 *10550 6600
–1.5 m *4800 3200 *6600 4150 *8600 6600 *8550 *8550
–3.0 m *3700 *3700 *4200 *4200 *5800 *5800
Front and rear outrigger on ground Arm length 1800 mm
7.5 m *4800 *4800
6.0 m *4450 *4450 *7450 6200
4.5 m *4400 4000 *4450 4000 *7850 6050 *10150 10000 *15600 *15600
3.0 m *4650 3600 6200 3950 *8250 5750 *11400 9250
1.5 m *5100 3500 6050 3850 *8350 5450 *11500 8650
0.0 m *5350 3600 *5750 3800 *7750 5250 *10350 8450
–1.5 m *4750 4050 *6500 5250 *8450 *8450 *8400 *8400
–3.0 m *3600 *3600 *4100 *4100 *5700 *5700
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-37
AH_25.book Page 38 Tuesday, March 23, 2004 9:41 AM
2F-38
AH_25.book Page 39 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 0.80 m3, Tires:10.00-20-14PR unit: kg
A MAX 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 2400 mm
7.5 m *4250 3150 *5050 3400
6.0 m *4000 2250 *6800 3450
4.5 m *4050 1800 5200 2150 *7450 3300 *9450 5400
3.0 m 4100 1600 5050 2050 7550 3050 *10850 4750
1.5 m 3950 1500 4950 1900 7250 2800 *11650 4300
0.0 m 4050 1550 4800 1850 6900 2550 *11050 4050
–1.5 m 4500 1700 4800 1800 6800 2450 *9500 3950 *9750 7650
–3.0 m *3950 2100 *5300 2600 *7100 4050 *8200 7900
Rear outrigger on ground Arm length 2400 mm
7.5 m *4250 3650 *5050 3900
6.0 m *4000 2600 *6800 3950
4.5 m *4050 2150 5800 2500 *7450 3800 *9450 6250
3.0 m *4200 1900 5650 2400 *8050 3550 *10850 5550
1.5 m 4450 1800 5500 2300 8200 3300 *11650 5100
0.0 m 4550 1850 5400 2200 7850 3050 *11050 4800
–1.5 m *4650 2050 *5150 2150 *7050 2950 *9500 4750 *9750 9350
–3.0 m *3950 2500 *5300 3100 *7100 4850 *8200 *8200
Front outrigger on ground and rear blade on ground Arm length 2400 mm
7.5 m *4350 *4350 *5100 *5100
6.0 m *4100 3500 *6900 5150
4.5 m *4100 2900 5300 3350 *7550 5000 *9600 8200
3.0 m 4200 2600 5200 3250 7650 4750 *11000 7450
1.5 m 4100 2500 5050 3100 7350 4450 *11850 7000
0.0 m 4200 2550 4950 3000 7000 4200 *11250 6700
–1.5 m 4650 2800 4900 3000 6900 4100 *9650 6600 *9900 *9900
–3.0 m *4000 3450 *5400 4250 *7200 6700 *8400 *8400
Front and rear outrigger on ground Arm length 2400 mm
7.5 m *4350 *4350 *5100 *5100
6.0 m *4100 *4100 *6900 6300
4.5 m *4100 3600 5900 4100 *7550 6150 *9600 *9600
3.0 m *4300 3250 5800 4000 *8150 5850 *11000 9450
1.5 m 4550 3150 5650 3900 8250 5600 *11850 8900
0.0 m 4700 3200 5550 3800 7950 5300 *11250 8550
–1.5 m *4750 3550 *5250 3750 *7200 5200 *9650 8500 *9900 *9900
–3.0 m *4000 *4000 *5400 5350 *7200 *7200 *8400 *8400
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-39
AH_25.book Page 40 Tuesday, March 23, 2004 9:41 AM
2F-40
AH_25.book Page 41 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 0.80 m3, Tires:10.00-20-14PR unit: kg
A MAX 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 2900 mm
7.5 m *2650 2600 *4450 3500
6.0 m 2400 1900 *3850 2200 *5300 3500
4.5 m 2000 1550 5250 2150 *6600 3350
3.0 m 1800 1400 5100 2050 7650 3100 *10350 4950 *16700 9350
1.5 m 1750 1300 4950 1900 7300 2850 *11450 4400
0.0 m 1750 1350 4800 1800 6950 2550 *11350 4050 *5950 *5950
–1.5 m 1900 1450 4750 1750 6750 2400 *10150 3900 *9200 7500
–3.0 m 2250 1750 *4950 1800 *5950 2450 *8050 3950 *10200 7700
Rear outrigger on ground Arm length 2900 mm
7.5 m *2650 *2650 *4450 4050
6.0 m *2550 2250 *3850 2550 *5300 4000
4.5 m *2550 1650 *5300 2550 *6600 3850
3.0 m *2650 1450 5700 2400 *7750 3600 *10350 5800 *16700 11200
1.5 m *2900 1400 5550 2300 8250 3350 *11450 5200
0.0 m *3250 1400 5400 2150 7900 3050 *11350 4850 *5950 *5950
–1.5 m *3900 1500 5300 2100 *7400 2900 *10150 4700 *9200 *9200
–3.0 m *3900 1800 *3950 2150 *5950 2950 *8050 4750 *10200 9400
Front outrigger on ground and rear blade on ground Arm length 2900 mm
7.5 m *2700 *2700 *4500 *4500
6.0 m *2600 *2600 *3900 3400 *5400 5250
4.5 m *2600 2550 5350 3350 *6700 5050
3.0 m *2700 2350 5200 3250 7700 4800 *10550 7750 *16950 15950
1.5 m *2950 2250 5050 3100 7400 4500 *11650 7100
0.0 m *3350 2300 4950 3000 7050 4200 *10550 6700 *6050 *6050
–1.5 m *4050 2500 4850 2950 6850 4050 *10350 6550 *9300 *9300
–3.0 m *5350 3150 *4000 2950 *6050 4100 *8200 6600 *10400 *10400
Front and rear outrigger on ground Arm length 2900 mm
7.5 m *2700 *2700 *4500 *4500
6.0 m *2600 *2600 *3900 *3900 *5400 *5400
4.5 m *2600 *2600 *5400 4150 *6700 6200
3.0 m *2700 *2700 5800 4050 *7850 5950 *10550 9750 *16950 *16950
1.5 m *2950 2800 5650 3900 8300 5600 *11650 9050
0.0 m *3350 2900 5550 3750 8000 5300 *11550 8600 *6050 *6050
–1.5 m *4050 3150 5450 3700 *7550 5150 *10350 8450 *9300 *9300
–3.0 m *4000 3700 *4000 3750 *6050 5200 *8200 *8200 *10400 *10400
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-41
AH_25.book Page 42 Tuesday, March 23, 2004 9:41 AM
2F-42
AH_25.book Page 43 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 0.80 m3, Tires:10.00-20-14PR unit: kg
A MAX 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 3500 mm
7.5 m *2650 2200 *2700 2200
6.0 m *2550 1650 *4150 2250
4.5 m *2550 1350 *4950 2250 *5400 3400
3.0 m *2650 1200 5100 2050 *7300 3150 *9600 5150
1.5 m *2900 1100 4950 1900 7350 2850 *11100 4500
0.0 m *3250 1150 4800 1750 7050 2600 *11450 4100 *6500 *6500
–1.5 m 3550 1250 4700 1700 6700 2350 *10700 3850 *8750 7400
–3.0 m *3900 1450 4650 1700 *6500 2350 *8950 3850 *12200 7500
Rear outrigger on ground Arm length 3500 mm
7.5 m *2650 2550 *2700 2600
6.0 m *2550 2100 *4150 2650
4.5 m *2550 1750 *4950 2550 *5400 3950
3.0 m *2650 1550 5750 2450 *7300 3650 *9600 6000
1.5 m *2850 1450 5550 2250 *8000 3350 *11100 5350
0.0 m *3200 1450 5350 2150 7950 3100 *11450 4850 *6500 *6500
–1.5 m *3800 1600 5250 2050 7650 2850 *10700 4650 *8750 *8750
–3.0 m *4900 1900 *4750 2050 *6550 2850 *8950 4600 *12200 9200
Front outrigger on ground and rear blade on ground Arm length 3500 mm
7.5 m *2700 *2700 *2750 *2750
6.0 m *2600 *2600 *4200 3500
4.5 m *2600 2300 *5050 3400 *5500 5150
3.0 m *2700 2050 5250 3250 *7450 4850 *9750 7950
1.5 m *2950 2000 5050 3100 7450 4550 *11250 7250
0.0 m *3300 2000 4900 2950 7150 4300 *11650 6750 *6600 *6600
–1.5 m 3650 2150 4800 2900 6850 4000 *10850 6500 *8900 *8900
–3.0 m 3950 2550 4800 2850 *6650 4000 *9100 6500 *12400 *12400
Front and rear outrigger on ground Arm length 3500 mm
7.5 m *2700 *2700 *2750 *2750
6.0 m *2600 *2600 *4200 *4200
4.5 m *2600 *2600 *5050 4200 *5500 *5500
3.0 m *2700 2650 5850 4050 *7450 6000 *9750 *9750
1.5 m *2950 2550 5650 3900 *8100 5650 *11250 9200
0.0 m *3300 2550 5500 3750 8050 5400 *11650 8650 *6600 *6600
–1.5 m *3950 2750 5400 3650 7750 5100 *10850 8400 *8900 *8900
–3.0 m *3950 3200 *4800 3650 *6650 5050 *9100 8350 *12400 *12400
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-43
AH_25.book Page 44 Tuesday, March 23, 2004 9:41 AM
2F-44
AH_25.book Page 45 Tuesday, March 23, 2004 9:41 AM
Conditions:
Boom: 5700 mm (18'8"), Bucket (SAE): 0.80 m3 (1.05 cu.yd), Tires: 10.00-20-14PR unit: kg (lb)
A MAX 7.5 m (25') 6.0 m (20') 4.5 m (15') 3.0 m (10')
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
When outrigger retracted Arm length 2410 mm (7'11")
6.0 m 3200 2100 *3600 3000
(20') (7100) (4600) (8000) (6600)
4.5 m 2700 1700 2900 1850 *4100 2800
(15') (5900) (3700) (6400) (4100) (9100) (6200)
3.0 m 2450 1500 2800 1750 4050 2600 *6400 4000
(10') (5400) (3300) (6200) (3900) (9000) (5700) (14100) (8800)
1.5 m 2350 1450 2700 1650 3850 2350 5900 3550
(5') (5200) (3100) (6000) (3700) (8400) (5200) (13100) (7900)
0m 2450 1450 2650 1600 3700 2250 5700 3350 *5400 *5400
(0') (5400) (3200) (5800) (3500) (8100) (4900) (12600) (7400) (1200) (1200)
–1.5 m 2750 1650 3650 2300 5650 3350 *9900 6300
(–5') (6000) (3600) (8000) (4900) (12500) (7400) (21800) (13900)
–3.0 m 3450 2100 3750 2300 5800 3450 *11900 6500
(–10') (7600) (4700) (8200) (5000) (12800) (7600) (26300) (14400)
–4.5 m 5650 3500 6150 3750
(–15') (12500) (7700) (13600) (8300)
When outrigger expanded Arm length 2410 mm (7'11")
6.0 m *3350 2800 *3600 *3600
(20') (7400) (6200) (8000) (8000)
4.5 m *3400 2350 *3850 2500 *4100 3750
(15') (7500) (5100) (8500) (5600) (9100) (8300)
3.0 m *3550 2100 *4200 2400 *4850 3500 *6400 5400
(10') (7900) (4600) (9200) (5300) (10700) (7700) (14100) (12000)
1.5 m *3950 2000 *4550 2300 *5600 3250 *7800 4950
(5') (8700) (4500) (10100) (5100) (12300) (7200) (17200) (11000)
0m *4600 2100 *4850 2250 *6150 3150 *8550 4750 *5400 *5400
(0') (10100) (4600) (10700) (5000) (13500) (6900) (18900) (10500) (12000) (12000)
–1.5 m *5000 2350 *6350 3100 *8700 4750 *9900 9250
(–5') (11100) (5200) (14000) (6800) (19200) (10400) (21800) (20400)
–3.0 m 5500 2950 *5950 3200 *8200 4850 *11900 9500
(–10') (12100) (6500) (13100) (7000) (18100) (10700) (26300) (21000)
–4.5 m *6000 4800 *6450 5150
(–15') (13300) (10600) (14200) (11400)
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on SAE Standard No.J1097. Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-45
AH_25.book Page 46 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 1800 mm
7.5 m *4800 4300
6.0 m 4150 2900 5200 3700
4.5 m 3350 2300 3350 2300 5050 3550 8200 5700 *16900 10850
3.0 m 3000 2050 3300 2250 4800 3350 7550 5100
1.5 m 2900 1950 3200 2200 4500 3050 7000 4650
0.0 m 3000 2000 3150 2100 4300 2850 6800 4450
–1.5 m 3350 2250 4300 2850 6850 4500 *9300 8650
–3.0 m *4050 2850 4500 3050 *6300 4650
Rear outrigger on ground Arm length 1800 mm
7.5 m *4800 *4800
6.0 m *4450 3750 *7700 4700
4.5 m *4400 3050 *4450 3050 *8550 4600 *11050 7350 *16900 14600
3.0 m *4650 2700 6300 3000 *9050 4350 *12400 6700
1.5 m *5100 2600 6150 2900 9000 4050 *12550 6200
0.0 m 5750 2700 6100 2850 *8500 3850 *11350 6000 *9300 *9300
–1.5 m *5250 3000 *7150 3850 *9300 6050
–3.0 m *4050 3800 *4600 4050 *6300 3200
Front outrigger on ground and rear blade on ground Arm length 1800 mm
7.5 m *4850 *4850
6.0 m *4500 *4500 *7850 5950
4.5 m *4500 3900 *4500 3900 8600 5800 *11200 9400 *17150 *17150
3.0 m *4700 3500 5700 3850 8350 5550 *12600 8700
1.5 m 5050 3400 5600 3750 8000 5250 *12750 8150
0.0 m 5250 3500 5550 3700 7750 5050 *11550 7950
–1.5 m *5350 3900 *7250 5000 *9450 8000 *9500 *9500
–3.0 m *4150 *4150 *4700 *4700 *6450 *6450
Front and rear outrigger on ground Arm length 1800 mm
*4850 *4850 *4850
6.0 m *4500 *4500 *7850 7100
4.5 m *4500 *4500 *4500 *4500 *8700 6950 *11200 *11200 *17150 *17150
3.0 m *4700 4250 6350 4650 *9200 6700 *12600 10750
1.5 m *5150 4100 6250 4550 9000 6400 *12750 10150
0.0 m 5850 4250 6200 4450 *8650 6150 *11550 9950
–1.5 m *5350 4750 *7250 6150 *9450 *9450 *9500 *9500
–3.0 m *4150 *4150 *4700 *4700 *6450 *6450
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-46
AH_25.book Page 47 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5400 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 1800 mm
7.5 m *5050 4900 *7000 6250
6.0 m *4550 3200 5250 3700 *7100 6300
4.5 m 3650 2500 5150 3600 *8450 5900 *12000 11450
3.0 m 3200 2150 3350 2250 4900 3400 7600 5100
1.5 m 3050 2050 3250 2150 4650 3150 7200 4750
0.0 m 3150 2100 3150 2100 4400 2950 6900 4500
–1.5 m 3550 2350 4400 2900 6900 4450 *12050 8500
–3.0 m 7050 4600
Rear outrigger on ground Arm length 1800 mm
7.5 m *5050 *5050 *7000 *7000
6.0 m *4550 4100 *6600 4750 *7100 *7100
4.5 m *4450 3300 *7050 4650 *8450 7600 *12000 *12000
3.0 m *4600 2900 *6150 3000 *7850 4400 *10300 6750
1.5 m *5050 2750 6300 2900 *8600 4150 *12000 6350
0.0 m *5800 2850 *6000 2850 *8900 3950 *12350 6100
–1.5 m *6950 3200 *8550 3950 *11700 6050 *12050 *12050
–3.0 m *9850 6250
Front outrigger on ground and rear blade on ground Arm length 1800 mm
7.5 m *5100 *5100 *7100 *7100
6.0 m *4600 *4600 *6700 6100 *7250 *7250
4.5 m *4500 4250 *7150 6000 *8600 *8600 *12150 *12150
3.0 m *4700 3800 *6250 3900 *8000 5700 *10450 8900
1.5 m *5100 3650 6200 3800 *8750 5450 *12200 8450
0.0 m *5900 3750 6100 3750 8750 5200 *12550 8200
–1.5 m 6900 4200 *8700 5200 *11900 8150 *12250 *12250
–3.0 m *10050 8350
Front and rear outrigger on ground Arm length 1800 mm
7.5 m *5100 *5100 *7100 *7100
6.0 m *4600 *4600 *6700 *6700 *7250 *7250
4.5 m *4500 *4500 *7150 *7150 *8600 *8600 *12150 *12150
3.0 m *4700 4500 *6250 4700 *8000 6850 *10450 *10450
1.5 m *5100 4350 6350 4600 *8750 6550 *12200 10400
0.0 m *5900 4500 *6100 4500 9000 6350 *12550 10100
–1.5 m *7050 5050 *8700 6300 *11900 10100 *12250 *12250
–3.0 m *10050 *10050
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-47
AH_25.book Page 48 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 2400 mm
7.5 m *4250 3500 *5050 3750
6.0 m 3600 2500 5300 3800
4.5 m 3000 2050 3450 2400 5150 3650 8450 5900
3.0 m 2700 1800 3350 2300 4900 3400 7700 5250
1.5 m 2600 1750 3250 2200 4650 3150 7200 4800
0.0 m 2650 1750 3150 2100 4350 2900 6900 4550
–1.5 m 2950 1950 3100 2100 4250 2800 6850 4500 *9750 8550
–3.0 m 3550 2400 4400 2950 6950 4600 *9100 8800
Rear outrigger on ground Arm length 2400 mm
7.5 m *4250 *4250 *5050 4800
6.0 m *4000 3250 *6800 4850
4.5 m *4050 2700 *6300 3150 *8100 4700 *9950 7550
3.0 m *4200 2450 6350 3050 *8800 4450 *11800 6850
1.5 m *4600 2350 6200 2900 9150 4150 *12700 6400
0.0 m 5150 2400 6100 2850 8800 2900 *12100 6100
–1.5 m *5150 2650 *5700 2800 *7800 3800 *10450 6050 *9750 *9750
–3.0 m *4350 3200 *5900 3950 *7800 6150 *9100 *9100
Front outrigger on ground and rear blade on ground Arm length 2400 mm
7.5 m *4350 *4350 *5100 *5100
6.0 m *4100 *4100 *6900 6050
4.5 m *4100 3500 5900 4000 *8250 5900 *10100 9650
3.0 m *4300 3150 5750 3900 8450 5650 *12000 8900
1.5 m 4600 3050 5650 3750 8150 5350 *12900 8400
0.0 m 4700 3150 5550 3700 7800 5100 *12300 8050
–1.5 m 5200 3450 5500 3650 7700 5000 *10600 8000 *9900 *9900
–3.0 m *4450 4150 *6000 5150 *7950 *7950 *9300 *9300
Front and rear outrigger on ground Arm length 2400 mm
*4850 *4350 *4350 *5100 *5100
6.0 m *4100 *4100 *6900 *6900
4.5 m *4100 *4100 *6350 4800 *8250 7100 *10100 *10100
3.0 m *4300 3850 6400 4700 *8900 6800 *12000 *10950
1.5 m *4700 3700 6300 4550 9150 6500 *12900 10400
0.0 m 5250 2800 6150 4450 8800 6200 *12300 10050
–1.5 m *5250 4200 *5800 4450 *7900 6100 *10600 10000 *9900 *9900
–3.0 m *4450 *4450 *6000 *6000 *7950 *7950 *9300 *9300
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-48
AH_25.book Page 49 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5400 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 2400 mm
7.5 m *4400 3900
6.0 m 3900 2700 5450 3850
4.5 m 3200 2200 3500 2400 5300 3750 *7500 6100
3.0 m 2850 1900 3400 2300 5000 3500 8100 5500
1.5 m 2750 1800 3300 2200 4750 3200 7400 4950
0.0 m 2800 1850 3150 2100 4500 3000 7000 4600
–1.5 m 3000 1950 3150 2050 4400 2900 6900 4500 *9150 8450
–3.0 m 3850 2550 4450 2950 6950 4550 14550 8700
Rear outrigger on ground Arm length 2400 mm
7.5 m *4400 *4400
6.0 m *4100 3550 *5850 4900
4.5 m *4050 2900 *5550 3150 *6450 4800 *7500 *7500
3.0 m *4200 2600 *6250 3050 *7350 4550 *9550 7200
1.5 m *4550 2450 6300 2950 *8300 4250 *11450 6550
0.0 m *5200 2500 6200 2850 *8850 4000 *12350 6200
–1.5 m 6100 2800 6150 2800 *8800 3900 *12150 6050 *10950 *10950
–3.0 m *6600 3450 *7800 3950 *10850 6150 *15400 12250
Front outrigger on ground and rear blade on ground Arm length 2400 mm
7.5 m *4500 *4500
6.0 m *4150 *4150 *5950 *5950
4.5 m *4100 3750 *5600 4100 6550 6100 *7600 *7600
3.0 m *4250 3400 6350 4000 *7500 5850 *9750 9400
1.5 m *4600 3250 6200 3850 *8400 5550 *11650 8700
0.0 m *5250 3350 6100 3750 8850 5300 *12550 8300
–1.5 m 6000 3700 6050 3700 8700 5150 *12350 8150 *11150 *11150
–3.0 m *6700 4500 *7950 5250 *11050 8250 *15650 *15650
Front and rear outrigger on ground Arm length 2400 mm
7.5 m *4500 *4500
6.0 m *4150 *4150 *5950 *5950
4.5 m *4100 *4100 *5600 4850 *6550 *6550 *7600 *7600
3.0 m *4250 4050 *6350 4750 *7500 6950 *9750 *9750
1.5 m *4600 3900 6400 4650 *8400 6650 *11650 10650
0.0 m *5250 4000 6250 4500 *9000 6400 *12550 10250
–1.5 m 6150 4450 6250 4500 8950 6300 *12350 10100 *11150 *11150
–3.0 m *6700 5450 *7950 6350 *11000 10200 *15650 *15650
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-49
AH_25.book Page 50 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 2900 mm
7.5 m *2650 *2650 *4450 3850
6.0 m *2550 2200 3550 2450 *5300 3850
4.5 m *2550 1800 3500 2450 5200 3700
3.0 m 2450 1600 3350 2300 4950 3450 8000 5500 16400 10300
1.5 m 2350 1550 3250 2200 4650 3200 7350 4900
0.0 m 2400 1550 3100 2100 4400 2950 6950 4550 *5950 *5950
–1.5 m 2600 1700 3050 2000 4200 2750 6800 4450 *9200 8450
–3.0 m 3050 2050 3100 2050 4250 2800 6850 4450 *11250 8650
Rear outrigger on ground Arm length 2900 mm
7.5 m *2650 *2650 *4450 *4450
6.0 m *2550 *2550 *3850 3200 *5300 4900
4.5 m *2550 2400 *5300 3150 *6600 4750
3.0 m *2650 2200 6350 3050 *8450 4500 *11300 7150 *18150 13950
1.5 m *2900 2100 6200 2900 9000 4200 *12500 6500
0.0 m *3300 2150 6050 2800 8850 3950 *12400 6150 *5950 *5950
–1.5 m *4000 2350 6000 2750 8150 3750 *11150 6000 *9200 *9200
–3.0 m *4350 2750 *4400 2800 *6600 3800 *8850 6050 *11250 *11250
Front outrigger on ground and rear blade on ground Arm length 2900 mm
7.5 m *2700 *2700 *4500 *4500
6.0 m *2600 *2600 *3900 *3900 *5400 *5400
4.5 m *2600 *2600 *5400 4050 *6700 5950
3.0 m *2700 *2700 5800 3900 8500 5700 *11450 9150 *18400 *18400
1.5 m *2950 2750 5650 3750 8200 5400 *12700 8500
0.0 m *3350 2800 5500 3650 7850 5100 *12600 8100 *6050 *6050
–1.5 m *4050 3050 5450 3600 7650 4950 *11300 7950 *9300 *9300
–3.0 m *4450 3600 *4500 3600 *6700 5000 *9000 8000 *11450 *11450
Front and rear outrigger on ground Arm length 2900 mm
*4850 *2700 *2700 *4500 *4500
6.0 m *2600 *2600 *3900 *3900 *5400 *5400
4.5 m *2600 *2600 *5400 4400 *6700 6600
3.0 m *2700 *2700 5950 4300 *8500 6300 *11300 10400 *18150 *18150
1.5 m *2950 *2950 5800 4150 8500 6000 *12650 9700
0.0 m *3350 3100 5650 4050 8150 5700 *12650 9250 *6050 *6050
–1.5 m *4050 3350 5600 4950 7950 5500 *11500 9100 *9300 *9300
–3.0 m *4600 4000 *4650 4000 *6900 5550 *9300 9150 *11450 *11450
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-50
AH_25.book Page 51 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5400 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 2900 mm
7.5 m *2800 *2800 *4150 3900
6.0 m *2600 2350 *3200 2500 *5150 3950
4.5 m *2550 1900 3550 2450 5400 3800 *6300 6300
3.0 m 2550 1700 3450 2350 5100 3550 8300 5700 *13450 10900
1.5 m 2450 1600 3300 2200 4750 3250 7550 5050 *6350 *6350
0.0 m 2500 1600 3150 2100 4500 3000 7050 4600 *6950 *6950
–1.5 m 2750 1750 3100 2000 4350 2850 6850 4450 *10200 8400
–3.0 m 3250 2150 4350 2850 6850 4450 14350 8550
Rear outrigger on ground Arm length 2900 mm
7.5 m *2800 *2800 *4150 *4150
6.0 m *2600 *2600 *3200 *3200 *5150 5000
4.5 m *2550 *2550 *4950 3200 *5850 4850 *6300 *6300
3.0 m *2650 2300 *5900 3100 *6850 4600 *8700 7400 *13450 *13450
1.5 m *2900 2200 6350 2950 *7900 4300 *10850 6700 *6350 *6350
0.0 m *3250 2250 6200 2800 *8650 4050 *12100 6250 *6950 *6950
–1.5 m *3950 2450 6100 2750 *8800 3850 *12250 6050 *10200 *10200
–3.0 m *5250 2950 *8250 3900 *11400 6050 *15250 12100
Front outrigger on ground and rear blade on ground Arm length 2900 mm
7.5 m *2850 *2850 *4250 *4250
6.0 m *2650 *2650 *3250 *3250 *5250 *5250
4.5 m *2600 *2600 *5000 4150 *5950 *5950 *6400 *6400
3.0 m *2700 *2700 *6000 4000 *6950 *5900 *8850 *8850 *13700 *13700
1.5 m *2950 *2950 6250 3850 *8050 5600 *11000 8850 *6450 *6450
0.0 m *3350 3000 6100 3750 *8800 5300 *12300 8350 *7050 *7050
–1.5 m *4000 3250 6000 3650 8650 5150 *12450 8150 *10350 *10350
–3.0 m *5350 3150 *8400 5150 *11600 8150 *15450 *15450
Front and rear outrigger on ground Arm length 2900 mm
7.5 m *2850 *2850 *4250 *4250
6.0 m *2650 *2650 *3250 *3250 *5250 *5250
4.5 m *2600 *2600 *5000 4500 *5950 *5950 *6400 *6400
3.0 m *2700 *2700 *6000 4400 *6950 6500 *8850 *8850 *13700 *13700
1.5 m *2950 *2950 5900 4250 *8050 6150 *11000 10000 *6450 *6450
0.0 m *3350 3250 5750 4100 8400 5850 *12300 9450 *7050 *7050
–1.5 m *4000 3550 5700 4000 8200 5700 *12450 9200 *10350 *10350
–3.0 m *5350 4250 8250 5700 *11600 9200 *15450 *15450
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-51
AH_25.book Page 52 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5700 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 3500 mm
7.5 m *2650 2450 *2700 2500
6.0 m *2550 1900 3600 2550
4.5 m 2400 1600 2450 1600 3550 2450 5300 3800
3.0 m 2150 1400 2400 1550 3400 2350 5000 3500 8200 5650
1.5 m 2100 1350 2300 1500 3250 2200 4700 3200 7500 5050
0.0 m 2100 1350 2250 1450 3100 2050 4450 2950 7000 4600 *6500 *6500
–1.5 m 2250 1450 3000 1950 4150 2750 6750 4400 *8750 8300
–3.0 m 2650 1700 3000 1950 4150 2700 6700 4350 *12350 8400
Rear outrigger on ground Arm length 3500 mm
7.5 m *2650 *2650 *2700 *2700
6.0 m *2550 2500 *4150 3300
4.5 m *2550 2150 *2850 2200 *4950 3200 *5400 4800
3.0 m *2650 1950 *3950 2150 *6200 3050 *7750 4550 *10450 7300
1.5 m *2900 1850 4500 2100 6200 2900 *8750 4250 *12150 6650
0.0 m *3250 1900 4450 2000 6050 2800 8900 3950 *12550 6150 *6500 *6500
–1.5 m *3900 2050 5950 2700 *8450 3700 *11700 5950 *8750 *8750
–3.0 m *4300 2350 *5250 2650 *7200 3700 *9850 5950 *12350 11900
Front outrigger on ground and rear blade on ground Arm length 3500 mm
7.5 m *2700 *2700 *2750 *2750
6.0 m *2600 *2600 *4200 4150
4.5 m *2600 *2600 *2900 2850 *5050 4050 *5500 *5500
3.0 m *2700 2550 *4000 2800 5800 3950 *7900 5750 *10600 9400
1.5 m *2950 2450 4150 2750 5650 3750 8250 5450 *12300 8650
0.0 m *3300 2500 4050 2650 5500 3600 7950 5150 *12750 8150 *6600 *6600
–1.5 m *3950 2700 5400 3550 7600 4900 *11900 7900 *8900 *8900
–3.0 m *4400 3100 *5350 3500 *7350 4850 *10000 7900 *12550 *12550
Front and rear outrigger on ground Arm length 3500 mm
*4850 *2700 *2700 *2750 *2750
6.0 m *2600 *2600 *4200 *4200
4.5 m *2600 *2600 *2900 *2900 *5050 4900 *5500 *5500
3.0 m *2700 *2700 *4000 3400 *6300 4750 *7900 6950 *10600 *10600
1.5 m *2950 *2950 4600 3350 6300 4550 *8900 6600 *12300 10700
0.0 m *3300 3100 4500 3250 6150 4400 8950 6300 *12750 10150 *6600 *6600
–1.5 m *3950 3300 6050 4300 *8600 6050 *11900 9900 *8900 *8900
–3.0 m *4400 3800 *5350 6400 *7350 6000 *10000 9850 *12550 *12550
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-52
AH_25.book Page 53 Tuesday, March 23, 2004 9:41 AM
Conditions: Boom: 5400 mm, Bucket (SAE): 1.0 m3, Tires:11.00-20-14PR unit: kg
A MAX 9.0 m 7.5 m 6.0 m 4.5 m 3.0 m
B Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs Cf Cs
Without outrigger Arm length 3500 mm
7.5 m *2700 2700
6.0 m *2550 2050 3650 2550 *4500 4050
4.5 m 2550 1700 3600 2500 *5100 3900
3.0 m 2300 1500 2400 1550 3450 2400 5200 3600 *7650 5900 *10850 *10850
1.5 m 2200 1400 2350 1500 3300 2200 4850 3300 4650 5150
0.0 m 2200 1400 2250 1450 3150 2050 4500 3000 7150 4700 *7600 *7600
–1.5 m 2400 1500 3000 1950 4300 2850 6850 4400 *9700 8300
–3.0 m 2800 1800 3000 1950 4250 2750 6750 4350 *13700 8350
Rear outrigger on ground Arm length 3500 mm
7.5 m *2750 *2750
6.0 m *2550 *2550 *3950 3350 *4500 *4500
4.5 m *2550 2300 *4750 3250 *5100 4950
3.0 m *2650 2050 *3350 2150 *5450 3150 *6250 4700 *7650 7600 *10850 *10850
1.5 m *2850 1950 *3950 2100 *6050 2950 *7400 4350 *9900 6800
0.0 m *3200 2000 *3650 2000 6200 2800 *8300 4050 *11650 6300 *7600 *7600
–1.5 m *3800 2150 6050 2700 *8750 3850 *12200 6000 *9750 *9750
–3.0 m *4900 2500 6050 2700 *8500 3850 *11800 5950 *13700 11850
Front outrigger on ground and rear blade on ground Arm length 3500 mm
7.5 m *2750 *2750
6.0 m *2600 *2600 *4000 *4000 *4550 *4550
4.5 m *2600 *2600 *4850 4200 *5200 *5200
3.0 m *2700 *2700 *3400 2850 *5550 4050 *6350 6000 *7750 *7750 *11050 *11050
1.5 m *2900 2650 *4000 2800 *6150 3900 *7500 5650 *10100 8950
0.0 m *3250 2650 *3700 2700 6100 3700 *8450 5350 *11800 8450 *7700 *7700
–1.5 m *3850 2850 5950 3600 8650 5100 *12450 8100 *9850 *9850
–3.0 m *5000 3350 5950 3600 8600 5050 *12000 8050 *13900 *13900
Front and rear outrigger on ground Arm length 3500 mm
7.5 m *2750 *2750
6.0 m *2600 *2600 *4000 *4000 *4550 *4550
4.5 m *2600 *2600 *4850 *4850 *5200 *5200
3.0 m *2700 *2700 *3400 *3400 *5500 4850 *6350 *6350 *7750 *7750 *11050 *11050
1.5 m *2900 *2900 *4000 3350 *6150 4650 *7500 6750 *10100 *10100
0.0 m *3250 *3250 *3700 3300 6250 4500 *8450 6450 *11800 10400 *7700 *7700
–1.5 m *3850 3500 6150 4350 8900 6250 *12450 10050 *9850 *9850
–3.0 m *5000 4050 6100 4350 *8650 6150 *12000 9950 *13900 *13900
* Load is limited by hydraulic capacity rather than tipping.
Ratings are based on ISO Standard No.10567.
Rated loads do not exceed 87% of hydraulic lift capacity or 75% of tipping load.
2F-53
AH_25.book Page 54 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2G
DEMOLITION
CONTENTS
Machine and attachment
Selection (guide line) .......................................... 2G-2
Attachment features and specifications:
Demolition high reach ......................................... 2G-4
Hydraulic crusher & cutter ................................. 2G-6
Hydraulic crucher ................................................ 2G-8
Concrete pulverizer ............................................. 2G-9
Jumbo crusher ................................................... 2G-11
Power fork .......................................................... 2G-12
Rotary grab ........................................................ 2G-13
2G-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
39.5m
36m
24m
15m
5~8m
FVBH0321
DEMOLITION
HIGH
REACH
2G-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
2. When carrying out demolition from inside the building being demolished
There is no space to carry out demolition work with machine from the ground level, or the building is too high
(higher than 6 stories) to demolished, and the demolition attachment does not reach, place the demolition
machine on the top floor of the building to be demolished. Start the demolition operation from the top, and
work down.
2G-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
4
4 -2
7670(25'2")
3 -3 3
2 -4 2
G 1
F -5 G 1
F
0 G.L. -6 G.L.
0
11 10 9 8 7 6 5 4 3 2 1 0 -7 11 10 9 8 7 6 5 4 3 2 1 0
(m) -8 (m)
D 13 12 11 10 9 8 7 6 5 4 3 2 1 0 D
E (m) D
E E
FVBH0318 FVBH0319 FVBH0320
Model
PC200LC-7 PC200LC-7 PC300LC-7
Item
High reach type 2-stage 3-stage
Structure
Boom type 1-piece 1-piece 1-piece 1-piece 3-piece 4-piece
Application For Both
For Demolition For Demolition For Demolition For Demolition For Demolition
Work Only Demolition & Work Only Work Only Work Only Work Only
Item Digging Work
Operating weight*1 kg (lb) 26040 (57,410) 25200 (55,560) 26480 (58,380) 39800 (87,740) 41150 (90,720) 41730 (92,000)
Max. allowable crusher weight kg (lb) 2300 (5,070) 2300 (5,070) 2100 (4,630) 2300 (5,070) 2300 (5,070) 2300 (5,070)
A: Max. working height* 2 mm (ft.in) 15200 (49’10”) 13500 (44’3”) 15200 (49’10”) 20000 (65’7”) 20500 (67’3”) 22500 (73’10”)
B: Arm top pin radius at max. working
height mm (ft.in) 3810 (12’6”) 3625 (11’11”) 3600 (11’10”) 4060 (13’4”) 4120 (13’6”) 4430 (14’6”)
C: Max. allowable working radius mm (ft.in) 8300 (27’3”) 9000 (29’6”) 7600 (24’11”) 11000 (36’1”) 11000 (36’1”) 11000 (36’1”)
D: Tail swing radius mm (ft.in) 2910 (9’7”) 2910 (9’7”) 2910 (9’7”) 3780 (12’5”) 3780 (12’5”) 3780 (12’5”)
E: Overall length*3 mm (ft.in) 13210 (43’4”) 11100 (36’5”) 11260 (36’11”) 14220 (46’8”) 14790 (48’6”) 16770 (55’)
F: Overall height*3 mm (ft.in) 3160 (10’4”) 3160 (10’4”) 3160 (10’4”) 3270 (10’9”) 3270 (10’9”) 3270 (10’9”)
G: Height of folded work equipment mm (ft.in) 2850 (9’4”) 3000 (9’10”) 2750 (9’) 3110 (10’2”) 2900 (9’6”) 2920 (9’7”)
Model
Item PC400LC-6
High reach type 3-stage
Structure
Boom type 1-piece 3-piece
Application For Demolition For Demolition
Item Work Only Work Only
Operating weight*1 kg (lb) 50500 (111,330) 52200 (115,080)
Max. allowable crusher weight kg (lb) 2300 (5,070) 2300 (5,070)
A: Max. working height* 2 mm (ft.in) 24000 (78’9”) 25000 (82’)
B: Arm top pin radius at max. working
mm (ft.in) 4350 (14’3”) 4335 (14’3”)
height
C: Max. allowable working radius mm (ft.in) 12300 (40’4”) 12300 (40’4”)
D: Tail swing radius mm (ft.in) 3800 (12’6”) 3800 (12’6”)
E: Overall length*3 mm (ft.in) 16610 (54’6”) 17610 (57’9”)
F: Overall height*3 mm (ft.in) 3420 (11’3”) 3420 (11’3”)
G: Height of folded work equipment mm (ft.in) 3100 (10’2”) 3170 (10’5”)
2G-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
7900
(16'5") 4745(15'7")
3195
810
3500 (28")
(11'6") FVBH0322
Model PC750LC
Item
A: Max. working height mm (ft.in) 39330 (129’)
B: Arm top pin radius at max. working height mm (ft.in) 6290 (20’8”)
C: Max. allowable working radius kg (lb) 20000 (65’7”)
Max. allowable crusher weight mm (ft.in) 2300 (5,070)
Boom assembly length mm (ft.in) 21770 (71’5”)
Bottom boom length mm (ft.in) 5150 (16’11”)
Intermediate boom length mm (ft.in) 3500 (11’6”)
Top boom length mm (ft.in) 13120 (43’1”)
Link length mm (ft.in) 2800 (9’2”)
Arm length mm (ft.in) 12500 (41’)
D: Weight of additional counterweight kg (lb) 10000 (22,050)
Operating weight (excluding crusher weight) kg (lb) 95000 (209,440)
2G-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
2G-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
e: Max. open width (at front-end cutter) mm (ft.in) 530 (1’9”) 670 (2’2”)
f: Arm tip width mm (ft.in) 120 (5’) 120 (5’)
h: Overall height mm (ft.in) 1300 (4’3”) 1680 (5’6”)
and performance
B: Max. crushing radius on ground mm (ft.in) 10425 (34’2”) 10610 (34’10”) 11860 (38’11”) 12025 (39’5”)
C: Max. dumping height mm (ft.in) 6358 (20’10”) 6205 (20’4”) 6100 (20’) 5935 (19’6”)
PC200/PC200LC, PC220/PC220LC, PC300/PC300LC, PC340LC &
Applicable Standard boom and arm PC210LC & PC240LC PC350/PC350LC
base
machine PC300LC &
With demotion high reach PC400LC
Remarks
Onsite installation of the crusher and cutter requires a base machine to be modified. For more details, you are recommended to
consult the Komatsu distributor.
2G-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Model PC200-7
PC60-7 PC120-6
Item Demolition specifications
Crusher model JRYB06 JRYB12 JRYB12R JRYB18 JRYB18R
360° none 360° none 360° 360° none 360°
Crusher rotation mechanism hydraulic hydraulic hydraulic hydraulic hydraulic
rotation rotation rotation rotation rotation
Operating weight kg (lb) 7300 (16,090) 12460 (27,470) 12460 (27,470) 22920 (50,530) 22970 (50,640)
KOMATSU
Engine model KOMATSU S4D102E KOMATSU SAA6D102E
4D95LE
Flywheel horsepower HP (kW)/RPM 54 (40)/1750 86 (64)/2200 143 (107)/1950
Crushing force (at X portion) kN/ton (U.S.ton) 441/45 (50) 686/70 (77) 686/70 (77) 980/100 (110) 980/100 (110)
Crushing force (at Y portion) kN/ton (U.S.ton) 588/60 (66) 931/95 (105) 931/95 (105) 1421/145 (160) 1421/145 (160)
a: Max. open width (at X portion) mm (ft.in) 510 (1’8”) 650 (2’2”) 650 (2’2”) 870 (2’10”) 870 (2’10”)
b: Max. open height mm (ft.in) 824 (2’8”) 1097 (3’7”) 1097 (3’7”) 1310 (4’4”) 1310 (4’4”)
c: Open depth mm (ft.in) 400 (1’4”) 580 (1’11”) 580 (1’11”) 695 (2’3”) 695 (2’3”)
d: Open width mm (ft.in) 367 (1’2”) 477 (1’7”) 477 (1’7”) 580 (1’11”) 580 (1’11”)
e: Max. open width
Crusher dimensions
mm (ft.in) 222 (9”) 312 (1’) 312 (1’) 350 (1’2”) 350 (1’2”)
and performance
B: Max. crushing radius on ground mm (ft.in) 6755 (22’2”) 9025 (29’7”) 9025 (29’7”) 10480 (34’5”) 11665 (38’3”)
C:Max. dumping height mm (ft.in) 4615 (15’2”) 5245 (17’2”) 5245 (17’2”) 6335 (20’9”) 6150 (20’2”)
Applicable With standard boom and PC60 PC120, PC120LC & PC130 PC200/PC200LC, PC220/PC220LC,
base arm PC210/PC210LC & PC240LC
machine With demotion high reach — PC300LC, PC400LC & PC750LC
Remarks
Onsite installation of the crusher requires a base machine to be modified. For more details, you are recommended to consult the
Komatsu distributor.
2G-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Model PC200-7
PC300-7
Item demolition specifications
Pulverizer model JHSM250 JHSM350
Operating weight kg (lb) 22590 (49,800) 25810 (56,900)
Engine model KOMATSU SAA6D102E KOMATSU SAA6D114E
Flywheel horsepower HP (kW)/RPM 143 (107)/1950 242 (180)/1900
Crushing force (at X portion) kN/ton (U.S.ton) 755/77 (85) 882/90 (99)
Crushing force (at Y portion) kN/ton (U.S.ton) 1078/110 (121) 1274/130 (143)
a: Max. open width mm (ft.in) 810 (2’8”) 850 (2’9”)
b: Open depth mm (ft.in) 755 (2’6”) 980 (3’3”)
c: Cutter length mm (ft.in) 180 (7”) 180 (7”)
Pulverizer dimensions
2G-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Model PC200-7
Item demolition specifications
Pulverizer model JHGV200
Operating weight kg (lb) 22570 (49,760)
Engine model KOMATSU SAA6D102E
Flywheel horsepower HP (kW)/RPM 143 (107)/1950
Crushing force (at X portion) kN/ton (U.S.ton) 735/75 (83)
Crushing force (at Y portion) kN/ton (U.S.ton) 981/100 (110)
a: Max. open width mm (ft.in) 870 (2’10”)
b: Open depth mm (ft.in) 910 (3’)
c: Cutter length mm (ft.in) 180 (7”)
Pulverizer dimensions
2G-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Model
PC300LC PC800SE PC1250-7
Specifications
Jumbo crusher model JCJC1500 JCJC1500R JCJC2300 JCJC2300R JCJC2600 JCJC2600R
360° non- 360° 360° non- 360° 360° non- 360°
Jumbo crusher rotation
hydraulic hydraulic hydraulic hydraulic hydraulic hydraulic
mechanism
rotation rotation rotation rotation rotation rotation
kg 33190 33340 82860 82860 113020 113020
Operating weight
(lb) (73,170) (73,500) (182,675) (182,675) (249,165) (249,165)
Engine model KOMATSU SAA6D114E KOMATSU SAA6D140E KOMATSU SAA6D170E
Flywheel horsepower HP (kW)/RPM 242 (180)/1900 454 (338)/1800 651 (485)/1800
Crushing force (at P portion) kN/ton (U.S.ton) 1764/180 (198) 1764/180 (198) 2744/280 (308) 2744/280 (308) 3234/330 (363) 3234/330 (363)
a: Max. open width mm (ft.in) 1500 (4’11”) 1500 (4’11”) 2300 (7’7”) 2300 (7’7”) 2600 (8’6”) 2600 (8’6”)
b: Max. open height mm (ft.in) 2090 (6’10”) 2090 (6’10”) 3300 (10’10”) 3300 (10’10”) 3550 (11’8”) 3550 (11’8”)
Jumbo crusher dimensions
c: Open depth mm (ft.in) 555 (1’10”) 555 (1’10”) 1050 (3’5”) 1050 (3’5”) 1065 (3’6”) 1065 (3’6”)
h: Overall height mm (ft.in) 2070 (6’9”) 2070 (6’9”) 3326 (10’11”) 3326 (10’11”) 3628 (11’11”) 3628 (11’11”)
and performance
w:Overall width mm (ft.in) 850 (2’9”) 850 (2’9”) 1590 (5’3”) 1590 (5’3”) 1590 (5’3”) 1590 (5’3”)
l: Overall length mm (ft.in) 2980 (9’9”) 3145 (10’4”) 4360 (14’4”) 4360 (14’4”) 5070 (16’8”) 5070 (16’8”)
Weight kg (lb) 3900 (8,600) 4050 (8,930) 11000 (24,250) 11000 (24,250) 12000 (26,455) 12000 (26,455)
kgf/cm2 320 320 320 320 320 320
Required oil pressure (PSI/MPa) (4,550/31.4) (4,550/31.4) (4,550/31.4) (4,550/31.4) (4,550/31.4) (4,550/31.4)
Required oil flow rate ltr (U.S.Gal)/min 500 (132) 500 (132) 800 (211) 800 (211) 800 (211) 800 (211)
Arm Opening sec. 7.5 7.5 8.0 8.0 11 11
speed Closing sec. 7.5 7.5 11 11 14 14
A: Max. crushing height mm (ft.in) 11265 (37’) 11430 (37’6”) 14000 (45’11”) 14000 (45’11”) 16000 (52’6”) 16000 (52’6”)
Working
range
Remarks
Onsite installation of the jumbo crusher requires modifications to the base machine. For more details, consult your Komatsu
distributor.
2G-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Model
PC30MR-2 PC50MR-2 PC78US-6 PC120-6 PC200-7
Item
Power fork type PF30B PF40B PF60B PF120B PF200B
Operating weight kg (lb) 3260 (7,190) 5170 (11,400) 7060 (15,560) 12170 (26,830) 19890 (43,850)
KOMATSU KOMATSU KOMATSU KOMATSU KOMATSU
Engine model
3D84E-5 4D88E-5 4D95LE S4D102E SAA6D102E
Flywheel horsepower HP (kW)/RPM 27.6 (20.6)/2500 39.4 (29.4)/2350 54 (40.5)/1850 86 (64)/2200 143 (107)/1950
a: Max. opening width mm (ft.in) 1040 (3’5”) 1220 (4’) 1505 (4’11”) 1815 (5’11”) 2080 (6’10”)
b: Tooth length mm (ft.in) 605 (2’) 720 (2’4”) 890 (2’11”) 1010 (3’4”) 1155 (3’9”)
c: Tooth width mm (ft.in) 300 (1’) 350 (1’2”) 405 (1’4”) 545 (1’9”) 700 (2’4”)
h: Overall height mm (ft.in) 505 (1’8”) 590 (1’11”) 680 (2’3”) 820 (2’8”) 1050 (3’5”)
w: Overall width mm (ft.in) 340 (1’1”) 395 (1’4”) 430 (1’5”) 600 (2’) 745 (2’5”)
l: Overall length mm (ft.in) 1015 (3’4”) 1190 (3’11”) 1480 (4’10”) 1765 (5’9”) 1940 (6’4”)
Weight kg (lb) 150 (330) 240 (530) 420 (930) 600 (1,325) 1030 (2,270)
A: Max. working height mm (ft.in) 4585 (15’1”) 5575 (18’3”) 6770 (22’3”) 8545 (28’) 8965 (29’5”)
B: Max. working radius mm (ft.in) 5005 (16’5”) 6085 (20’) 6185 (20’4”) 8125 (26’8”) 9460 (31’)
PC100-6,
PC120/PC120LC-6,
PC27R-8, PC35R-8, PC45R-8, PC60-7, PC200/PC200LC-7,
PC27MR-1, PC40MR-2, PC78MR-6, PC130-6 & PC220/PC220LC-7
Applicable base machine PC160LC-7,
PC30MR-2, PC50MR-2, PC78US-6/ & PC230-7,
PC128US-2,
PC35MR-2 PC58UU-3 PC78UU-6 PC228US-3
PC138US-2 &
PC128UU-2
Remarks:
An excessive stress may be applied to the arm depending on the type of work the machine engages in. It is requested, therefore,
to weld a reinforcing steel plate both on the upper and lower surfaces of the arm. For more information on the reinforcement of the
arm, see the operation and maintenance manual.
2G-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
2G-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2H
RAILWAY MAINTENANCE
MACHINES
CONTENTS
Railway maintenance system ................................. 2H-2
Features .................................................................... 2H-2
Specifications ........................................................... 2H-3
Shipping dimensions ............................................... 2H-4
Working ranges, digging force ............................... 2H-5
2H-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
FEATURES
Easy exit from the main line.
• Should a failure occur in the engine or hydraulic system to disable traveling, it is possible to manually raise
the machine with jacks and move it to a nearby emergency station.
In addition, an auxiliary engine for emergency exit is optionally provided.
Height automatic stop system
• If maximum working height is set to a safe level, when the boom rises to this level during work, it will stop
automatically.
Therefore, there is no risk of contacting overhead wires.
Insulation measures to prevent short-circuit faults.
• Insulating measures adopted at the points-of-contact of machine with rails ensure that shorting between
right and left rails and interference with signals, etc., will not occur.
Works and deadheading performed entirely on-rail.
• All works are performed on the rails, thus ensuring that no damage will occur to ballast, signal boxes,
cables, etc.
Quick traveling speed (on rails)
• Large-diameter [380mm (15")] insulated traveling wheels are provided, allowing safe traveling over
junction points and substantially reducing travel time between sites.
Easy rail access and exit
• With rubber crawlers, access and exit to/from the rail line is easy, and causes no damage to rails.
Two gauge types are available;
A machine dedicated to narrow gauge and one dedicated to both narrow and broad gauges.
2H-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
2H-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
132
730(2'5")
5(4 '5")
'4") 5(3
W.G:2354(7'9")
103
N.G:1980(6'6")
910(3')
7")
1360(4'6") 0(3'
W.G:1435(4'8") 108
400(16")
W.G:2754(9'0")
680(2'3")
90(3.5")
1980(6'6") 5680(18'8")
3825(12'7") 1035(3'5")
980(3'3")
2111(6'11")
2750(9')
25510") 629(2'1") 920(3')
884(2'11")
550(1'10")
525(1'9")
420(1'5")
200(7.9")
990(3'3") 1940(6'4")
N.G:1067(3'6") 1495(4'11") 1495(4'11")
2990(9'10")
N.G:2380(7'10")
PC78UUT-6
2H-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
*A
B
F
E
Bucket
Boom Arm Arm crowd
A mm B mm C mm D mm E mm F mm G mm digging
length length force
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) force
m(ft.in) m(ft.in) kg (lb/kN)
kg (lb/kN)
3.41 1.62 3325 2945 1630 4000 2900 5575 3270 4000 2650
PC58UUT-3
(11'2") (5'4") (10'11") (9'8") (5'4") (13'1") (9'6") (18'3") (10'9") (8820/39.2) (5840/26.0)
3.75 1.72 3815 2820 1345 3980 3110 6100 4030 6250 3960
PC78UUT-6
(12'4") (5'9") (12'6") (9'3") (4'5") (13'1") (10'2") (20'0") (13'3") (13780/61.3) (8740/38.8)
* Limited operating height
2H-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 2J
OTHERS
CONTENTS
Telescopic clamshell ................................................2J-2
Caisson specs (Electric powered excavator) .........2J-2
Underground demolition specs ...............................2J-3
GEO master (Foundation excavating specs) ..........2J-3
Double arms (For reverse-side ditching) ................2J-4
Tilting cab ..................................................................2J-4
High-mount cab .........................................................2J-5
Muddy soil excavating specs ..................................2J-6
Tower yarder ..............................................................2J-7
Aqua-digger (Backhoe type specs) .........................2J-8
2J-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
OTHERS
Telescopic Clamshell
This TELESCOPIC CLAMSHELL exhibits the best performance in deep pit bottom excavating works for a
multi-story building foundation or caisson. The combination of both a clamshell of maximum bucket capacity
and a telescopic arm of higher extension-retraction speed in this machine class greatly improve its working
efficiency.
PG15SVE
2J-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
OTHERS
<MAJOR FEATURES>
1. Hydraulic circuit for rotatory hydraulic crusher is equipped as standard.
2. A machine with extra-low height cab can travel under 2.5-meter beam in height.
3. Two-piece booms adopted on this machine realize pull-down operation of 3.5-meter wall in height and
provide a compact transport posture.
4. Dustproof net adopted on the side cover prevents the engine from getting dust intrusion into the engine
compartment even in dusty demolition job sites.
MODEL PC138US
OPERATING WEIGHT (kg) 15900
FLYWHEEL HORSEPOWER (kW(PS)/rpm) 64(87)/2200
REACH AT MAX.HEIGHT* (mm) 8715
WORKING MAX.WORKING REACH* (mm) 7735
RANGE MAX.REACH BELOW GROUND* (mm) 4060
REAR TAIL SWING RADIUS (mm) 1595
* With Crusher & Cutter (C & C17R)
PC35MR PC75UU
2J-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
OTHERS
FENCE
SIDE DITCH
MAIN PIPE
BRANCH PIPE
Tilting Cab
This excavator-based machine can keep the operator’s compartment horizontal even on a sloped terrain with
a tilt device consisting of two control cylinders, thus ensuring efficient and comfortable logging operation in
forest or woods.
PC75UU
2J-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
OTHERS
PC78US-5
High-mount Cab
A high-mount cab provides the operator with wider and clearer field view, thus facilitating loading or unloading
of scrap on or off a truck and charging or discharging into or out of scrap processing machines. The hydraulic
elevating cab lowered ensures better transportability.
FIXED TYPE HIGHT-MOUNT CAB OUTLINE DRAWING
PC300LC
The high mount cab can be installed on the LC type, too, such as PC200LC and PC300LC.
2J-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
WORKING RANGE
MODEL PC200-7
OPERATING WEIGHT (kg) 25000
FLYWHEEL HORSEPOWER (kW(PS)/rpm) 107(145)/1950
FLOAT CAPACITY (m3) 34
BUCKET CAPACITY (m3) 0.60
GROUND PRESSURE
SOFT GROUND (kPa(kgf/cm2)) 11.8(0.12)
2J-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Tower Yarder
An excavator-based yarding machine with a winch, called TOWER YARDER, features an excellent
controllability and high mobility. It also ensures easy operation without requiring any sub-wire ropes and
skylines, thus enabling great improvement of job efficiency in timber yarding.
2J-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
PC1800
PC3000
2J-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
PC1400
Boom length m 8.0 12.0 12.0 12.0 14.0 14.0 14.0
Arm length m 3.6 5.0 7.0 10.0 5.0 7.0 10.0
Bucket capacity m3
SAE (CECE) heaped 10.0 (9.1) 6.5 (5.9) 6.5 (5.9) 3.5 (3.2) 3.5 (3.2) 3.3 (3.0) 3.3 (3.0)
struck 7.8 5.1 5.1 2.7 2.7 2.5 2.5
A: Max. digging depth m 8.0 12.7 14.7 17.1 14.0 15.7 18.7
B: Max. digging depth of out for 7m m 6.1 11.6 13.8 16.4 12.9 14.8 18.1
C: Turn radius m 7.4 9.3 8.9 8.5 10.1 10.0 9.9
D: Max. dumping height m 4.5 6.2 4.2 1.7 8.0 6.3 3.3
kN 560 420 390 305 470 425 310
Max. bucket digging force
(ton) (54.9) (41.2) (38.2) (29.9) (46.1) (41.7) (30.4)
kN 500 400 320 250 415 325 250
Max. arm crowd force
(ton) (49.0) (39.2) (31.4) (24.5) (40.7) (31.9) (24.5)
Estimated hourly production m3/h 425 280 280 150 150 136 135
Note: Measurement depend on pontoon height of 1.0 m above water line.
PC3000
Boom length m 12.0 12.0 15.0 15.0 15.0 15.0 15.0 15.0
Arm length m 5.0 8.5 5.0 8.5 10.0 7.0 12.0 12.0
Bucket capacity m3
SAE (CECE) heaped 11.0 (10.0) 8.5 (7.6) 6.1 (5.6) 4.5 (4.1) 4.5 (4.1) 5.0 (4.5) 3.5 (3.1) 3.0 (2.6)
struck 8.5 6.6 4.7 3.5 3.5 3.9 2.7 2.3
A: Max. digging depth m 14.0 17.2 16.0 19.1 20.6 18.0 22.6 24.3
B: Max. digging depth of out for 7m m 12.9 16.3 15.0 18.4 20.0 17.2 22.0 24
C: Turn radius m 10.5 10.5 11.5 11.4 11.5 11.5 11.5 12
D: Max. dumping height m 6.2 3.0 9.2 6.1 4.7 7.2 2.8 4.3
kN 680 400 760 500 380 770 375 375
Max. bucket digging force
(ton) (69.4) (40.8) (77.5) (51.0) (38.9) (78.5) (38.3) (38.3)
kN 570 400 600 420 370 470 315 315
Max. arm crowd force
(ton) (58.1) (40.8) (61.2) (42.8) (37.7) (47.9) (32.1) (32.1)
Estimated hourly production m3/h 464 360 256 191 191 215 150 130
Note: Measurement depend on pontoon height of 1.0 m above water line.
2J-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
MEMO
CONTENTS
SECTION 3
INDEX
SECTION 3A
WHEEL LOADERS
CONTENTS
Features .................................................................... 3A-2
Specifications ........................................................... 3A-8
Performance data, dimensions ............................. 3A-17
Performance curves, travel time charts ............... 3A-95
Definitions ............................................................ 3A-102
Attachment availability ........................................ 3A-105
Bucket features .................................................... 3A-110
Teeth features ........................................................3A-111
Bucket selection .................................................. 3A-112
Teeth selection ..................................................... 3A-126
Fork equipment features ..................................... 3A-129
Log-loader operations ......................................... 3A-131
Lumber grapple specifications ........................... 3A-132
Dumping fork specifications ............................... 3A-133
Lumber fork specifications ................................. 3A-134
Log grapple specifications ................................. 3A-135
Logger performance ............................................ 3A-137
High lift boom specifications .............................. 3A-144
Tire availability ..................................................... 3A-145
Wheel loader and dump truck combination ...... 3A-148
Production ............................................................ 3A-152
3A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Excellent productivity
• Dual hydraulic speed system to reduce cycle time
(WA320-WA900, except WA320-3 CUSTOM, FAST
WA800-3)
• VOHS (Variable Output Hydraulic System) to
reduce cycle time (WA1200) SLOW
• High capacity engine with power to spare
The powerful Komatsu engine provides fuel-
efficient operation.
FLW00001
FVBH0323
3A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
FLW00052
Disc
(wet type multiple disc)
3A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
surfaces. FVBH0324
3A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Increased reliability
• Wet multi-disc brakes and fully hydraulic
braking system mean lower maintenance costs
and higher reliability. Wet disc brakes are fully
sealed. Contaminants are kept out, reducing wear
and resulting maintenance.
Brakes require no adjustments for wear, meaning
even lower maintenance. The new parking brake
is also an adjustment-free, wet multi-disc for high
reliability and long life.
3A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
buffer rings
dust seal
rod packing
• Komatsu components
Komatsu manufactures the engine, torque Torque converter
converter, transmission, hydraulic units, electric
parts, and even each bolt on this wheel loader.
• Cathion Electrodeposition primer paint/
powder coating final paint
Cathion electrodeposition paint is applied as a
primer paint and powder coating is applied as
topcoat to the exterior metal sheet parts. Transmission Engine
Front axle Rear axle
• Sealed DT connectors
Main harnesses and controller connectors are
equipped with sealed DT connectors providing
high reliability, water resistance and dust
resistance.
FVW00925
3A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
• Kick-down switch
With the touch of a finger, the kick-down switch
automatically down shifts from second to first
when beginning the digging cycle. Transmission controller
FZW00949
• Low-noise design
The large cab is mounted with Komatsu's unique
ROPS/FOPS viscous mounts. The low-noise Floor
engine, hydraulically driven fan, and hydraulic
pumps are mounted with rubber cushions, and Rubber
the cab sealing is improved to provide a quiet,
low-vibration, dustproof with pressurizing, and Frame
comfortable operating environment.
3A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
3A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Model WA320-3
Item WA320-5 CUSTOM WA380-5 WA380-3
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 166 (124)/2000 153 (114)/2350 187 (140)/2000 187 (140)/2200
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 4.0-13.0 (2.5-8.1)** 7.5 (4.7) 6.3 (3.9) 7.1 (4.4)
2nd 13.0 (8.1) 12.0 (7.5) 11.4 (7.1) 11.4 (7.1)
3rd 18.0 (11.2) 21.0 (13.0) 20.2 (12.6) 20.2 (12.6)
4th 38.0 (23.6) 34.0 (21.1) 31.5 (19.6) 31.5 (19.6)
Reverse 1st 4.0-13.0 (2.5-8.1)** 7.8 (4.8) 6.7 (4.2) 7.4 (4.6)
2nd 13.0 (8.1) 12.5 (7.8) 11.8 (7.3) 11.8 (7.3)
3rd 18.0 (11.2) 22.0 (13.7) 21.0 (13.0) 21.0 (13.0)
4th 38.0 (23.6) 35.0 (21.7) 32.5 (20.2) 32.5 (20.2)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D102E SA6D102E SAA6D114E S6D108
No. of cylinders- mm (in) 6-102 x 120 6-102 x 120 6-114 x 135 6-108 x 130
bore x stroke (4.02 x 4.72) (4.02 x 4.72) (4.49 x 5.31) (4.3 x 5.1)
Piston displacement ltr. (cu.in) 5.88 (359) 5.88 (359) 8.27 (505) 7.15 (436)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 228 (60.2) 200 (52.8) 300 (79.3) 287 (75.8)
3A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Model
Item WA480-5 WA500-3 WA600-3 WA600-3**
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 271 (202)/2000 315 (235)/2100 478 (357)/2000 478 (357)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 6.3 (3.9) 6.7 (4.2) 6.4 (4.0) 6.4 (4.0)
2nd 12.1 (7.5) 12.0 (7.5) 11.1 (6.9) 11.1 (6.9)
3rd 21.6 (13.4) 20.2 (12.6) 18.8 (11.7) 18.8 (11.7)
4th 34.3 (21.3) 33.0 (20.5) 30.3 (18.8) 30.3 (18.8)
Reverse 1st 6.6 (4.1) 7.5 (4.7) 7.1 (4.4) 7.1 (4.4)
2nd 12.8 (8.0) 13.4 (8.3) 12.2 (7.6) 12.2 (7.6)
3rd 22.8 (14.2) 22.5 (14.0) 20.5 (12.7) 20.5 (12.7)
4th 35.8 (22.2) 36.1 (22.4) 32.7 (20.3) 32.7 (20.3)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D125E SA6D140E SAA6D170E SAA6D170E
No. of cylinders- mm (in) 6-125 x 150 6-140 x 165 6-170 x 170 6-170 x 170
bore x stroke (4.9 x 5.9) (5.5 x 6.5) (6.69 x 6.69) (6.69 x 6.69)
Piston displacement ltr. (cu.in) 11.04 (674) 15.24 (930) 23.15 (1413) 23.15 (1413)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 417 (110.2) 450 (118.9) 670 (177) 670 (177)
Model
WA600-3*** WA600-3*4 WA700-3 WA700-3**
Item
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 478 (357)/2000 478 (357)/2000 672 (502)/2000 672 (502)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 6.4 (4.0) 6.4 (4.0) 6.4 (4.0) 6.4 (4.0)
2nd 11.1 (6.9) 11.1 (6.9) 11.1 (6.9) 11.1 (6.9)
3rd 18.8 (11.7) 18.8 (11.7) 18.7 (11.6) 18.7 (11.6)
4th 30.3 (18.8) 30.3 (18.8) 30.0(18.6) 30.0(18.6)
Reverse 1st 7.1 (4.4) 7.1 (4.4) 7.1 (4.4) 7.1 (4.4)
2nd 12.2 (7.6) 12.2 (7.6) 12.3 (7.6) 12.3 (7.6)
3rd 20.5 (12.7) 20.5 (12.7) 20.5 (12.7) 20.5 (12.7)
4th 32.7 (20.3) 32.7 (20.3) 32.3 (20.1) 32.3 (20.1)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D170E SAA6D170E SAA6D170E SAA6D170E
No. of cylinders- mm (in) 6-170 x 170 6-170 x 170 6-170 x 170 6-170 x 170
bore x stroke (6.7 x 6.7) (6.7 x 6.7) (6.69 x 6.69) (6.69 x 6.69)
Piston displacement ltr. (cu.in) 23.15 (1413) 23.15 (1413) 23.15 (1413) 23.15 (1413)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 670 (177) 670 (177) 1100 (290.6) 1100 (290.6)
* See PERFORMANCE DATA
** With high lift boom
*** Load & Carry spec
*4 Stone handling spec
3A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Model
Item WA800-3 WA800-3** WA800-3***
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 808 (603)/2000 808 (603)/2000 808 (603)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 7.0 (4.3) 7.0 (4.3) 7.0 (4.3)
2nd 12.3 (7.6) 12.3 (7.6) 12.3 (7.6)
3rd 28.0 (17.4) 28.0 (17.4) 28.0 (17.4)
4th
Reverse 1st 7.1 (4.4) 7.1 (4.4) 7.1 (4.4)
2nd 12.4 (7.7) 12.4 (7.7) 12.4 (7.7)
3rd 28.3 (17.6) 28.3 (17.6) 28.3 (17.6)
4th
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU
SA12V140 SA12V140 SA12V140
No. of cylinders- mm (in) 12-140 x 165 12-140 x 165 12-140 x 165
bore x stroke (5.5 x 6.5) (5.5 x 6.5) (5.5 x 6.5)
Piston displacement ltr. (cu.in) 30.5 (1,861) 30.5 (1,861) 30.5 (1,861)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 1425 (376.5) 1425 (376.5) 1425 (376.5)
Model
WA900-3 WA900-3** WA1200-3 WA1200-3**
Item
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 853 (637)/2000 853 (637)/2000 1560 (1165)/1900 1560 (1165)/1900
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 7.0 (4.3) 7.0 (4.3) 6.3 (3.9) 6.3 (3.9)
2nd 12.3 (7.6) 12.3 (7.6) 11.5 (7.1) 11.5 (7.1)
3rd 28.0 (17.4) 28.0 (17.4) 19.8 (12.3) 19.8 (12.3)
4th
Reverse 1st 7.1 (4.4) 7.1 (4.4) 7.4 (4.6) 7.4 (4.6)
2nd 12.4 (7.7) 12.4 (7.7) 13.4 (8.3) 13.4 (8.3)
3rd 28.3 (17.6) 28.3 (17.6) 22.6 (14.0) 22.6 (14.0)
4th
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU CUMMINS CUMMINS
SA12V140 SA12V140 QSK60 QSK60
No. of cylinders- mm (in) 12-140 x 165 12-140 x 165 16-159 x 190 16-159 x 190
bore x stroke (5.5 x 6.5) (5.5 x 6.5) (6.3 x 7.5) (6.3 x 7.5)
Piston displacement ltr. (cu.in) 30.5 (1,861) 30.5 (1,861) 60.2 (3,674) 60.2 (3,674)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 1430 (377.8) 1430 (377.8) 5100 (1,347) 5100 (1,347)
* See PERFORMANCE DATA
** With high lift boom
*** Load & Carry spec
3A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Model
Item WA320-5*4 WA380-5*4 WA400-5*4 WA450-5*4
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 166 (124)/2000 187 (140)/2000 200 (149)/2200 261 (195)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 4.0-13.0 (2.5-8.1)** 6.8 (4.2) 6.8 (4.2) 6.3 (3.9)
2nd 13.0 (8.1) 12.3 (7.6) 12.3 (7.6) 12.1 (7.5)
3rd 18.0 (11.2) 21.4 (13.3) 21.4 (13.3) 21.7 (13.5)
4th 38.0 (23.6) 34.0 (21.1) 34.0 (21.1) 34.9 (21.7)
Reverse 1st 4.0-13.0 (2.5-8.1)** 7.3 (4.5) 7.3 (4.5) 6.7 (4.2)
2nd 13.0 (8.1) 12.8 (8.0) 12.8 (8.0) 12.8 (8.0)
3rd 18.0 (11.2) 22.6 (14.0) 22.6 (14.0) 23.0 (14.3)
4th 38.0 (23.6) 35.0 (21.7) 35.0 (21.7) 36.0 (2.4)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D102E SAA6D114E SAA6D114E SAA6D125E
No. of cylinders- mm (in) 6-102 x 120 6-114 x 135 6-114 x 135 6-125 x 150
bore x stroke (4.0 x 4.7) (4.5 x 5.3) (4.5 x 5.3) (4.9 x 5.9)
Piston displacement ltr. (cu.in) 5.88 (359) 8.27 (505) 8.27 (505) 11.04 (674)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 228 (60.2) 300 (79.3) 300 (79.3) 390 (103)
* See PERFORMANCE DATA
*4 Canada source
*5 USA source
** 1st speed can be set variably
3A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
Model
Item WA480-5*4 WA500-3*5 WA600-3*5 WA700-3*5
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 271 (202)/2000 315 (235)/2100 450 (336)/2000 672 (502)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 6.3 (3.9) 7.1 (4.4) 6.4 (4.0) 6.4 (4.0)
2nd 12.1 (7.5) 12.6 (7.8) 11.0 (6.8) 11.1 (6.9)
3rd 21.6 (13.4) 21.2 (13.2) 18.8 (11.7) 18.7 (11.6)
4th 34.3 (21.3) 34.8 (21.6) 30.3 (18.8) 30.0(18.6)
Reverse 1st 6.6 (4.1) 7.9 (4.9) 7.1 (4.4) 7.1 (4.4)
2nd 12.8 (8.0) 14.1 (8.6) 12.2 (7.6) 12.2 (7.6)
3rd 22.8 (14.2) 23.5 (14.6) 20.5 (12.7) 20.5 (12.7)
4th 35.8 (22.2) 38.1 (23.7) 32.7 (20.3) 32.3 (20.1)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D125E SA6D140E SAA6D170E SAA6D170E
No. of cylinders- mm (in) 6-125 x 150 6-140 x 165 6-170 x 170 6-170 x 170
bore x stroke (4.9 x 5.9) (5.5 x 6.5) (6.7 x 6.7) (6.7 x 6.7)
Piston displacement ltr. (cu.in) 11.04 (674) 14 (855) 23.15 (1,410) 23.15 (1,412)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 417 (110.2) 448 (118.4) 670 (177) 1100 (290.6)
3A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
Model
Item WA95-3*6 WA115-3*6 WA250-5*6 WA320-5*6
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 74 (55)/2500 87 (65)/2200 137 (102)/2000 166 (124)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 5.7 (3.5) 7.0 (4.3) 4.0-13.0 (2.5-8.1)** 4.0-13.0 (2.5-8.1)**
2nd 20.0 (12.4) 20.0 (12.4) 13.0 (8.1) 13.0 (8.1)
3rd 18.0 (11.2) 18.0 (11.2)
4th 38.0 (23.6) 38.0 (23.6)
Reverse 1st 5.7 (3.5) 7.0 (4.3) 4.0-13.0 (2.5-8.1)** 4.0-13.0 (2.5-8.1)**
2nd 20.0 (12.4) 20.0 (12.4) 13.0 (8.1) 13.0 (8.1)
3rd 18.0 (11.2) 18.0 (11.2)
4th 38.0 (23.6) 38.0 (23.6)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 38.5 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
4D106E S4D106E SAA6D102E SAA6D102E
No. of cylinders- mm (in) 4-106 x 125 4-106 x 125 6-102 x 120 6-102 x 120
bore x stroke (4.17 x 4.92) (4.17 x 4.92) (4.0 x 4.7) (4.0 x 4.7)
Piston displacement ltr. (cu.in) 4.412 (269) 4.412 (269) 5.9 (360) 5.9 (360)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 130 (33.8) 120 (31.7) 184 (48.6) 228 (60.2)
* See PERFORMANCE DATA
*6 Germany source
** 1st speed can be set variably
3A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
Model
Item WA380-5*6 WA400-5*6 WA470-5*6 WA480-5*6
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 187 (140)/2000 208 (154)/2000 261 (195)/2000 271 (202)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 6.8 (4.2) 6.8 (4.2) 6.3 (3.9) 6.3 (3.9)
2nd 12.3 (7.6) 12.4 (7.7) 12.1 (7.5) 12.1 (7.5)
3rd 22.6 (14.0) 22.7 (14.1) 22.8 (14.2) 22.6 (14.0)
4th 38.3 (23.9) 38.5 (23.9) 39.7 (24.7) 39.6 (24.6)
Reverse 1st 7.3 (4.5) 7.3 (4.5) 6.7 (4.2) 6.6 (4.1)
2nd 12.8 (8.0) 12.9 (8.0) 12.8 (8.0) 12.8 (8.0)
3rd 23.9 (14.9) 24.0 (14.9) 24.7 (15.3) 23.8 (14.8)
4th 39.5 (24.5) 39.6 (24.6) 40.9 (25.4) 41.3 (25.7)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D114E SAA6D114E SAA6D125E SAA6D125E
No. of cylinders- mm (in) 6-114 x 135 6-114 x 135 6-125 x 150 6-125 x 150
bore x stroke (4.49 x 5.31) (4.49 x 5.31) (4.92 x 5.91) (4.92 x 5.91)
Piston displacement ltr. (cu.in) 8.27 (505) 8.27 (505) 11.04 (674) 11.4 (674)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 300 (79.3) 300 (79.3) 390 (103.0) 417 (110.2)
Model WA500-3*6
Item
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 315 (235)/2100
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 7.1 (4.4)
2nd 12.6 (7.8)
3rd 21.2 (13.2)
4th 34.8 (21.6)
Reverse 1st 7.9 (4.9)
2nd 14.1 (8.8)
3rd 23.5 (14.6)
4th 38.1 (23.7)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU
SA6D140E
No. of cylinders- mm (in) 6-140 x 165
bore x stroke (5.51 x 6.5)
Piston displacement ltr. (cu.in) 15.24 (930)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 460 (121.5)
* See PERFORMANCE DATA
*6 Germany source
*7 China source
3A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
Model
Item WA500-3*7 WA600-3*7
OPERATING WEIGHT* kg (lb)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 315 (235)/2100 439 (327)/2000
BUCKET CAPACITY* m3 (cu.yd)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 6.7 (4.2) 7.4 (4.6)
2nd 12.0(7.5) 12.7 (7.9)
3rd 20.2 (12.6) 21.0 (13.0)
4th 33.0 (20.5) 33.5 (20.8)
Reverse 1st 7.5 (4.7) 8.2 (5.1)
2nd 13.4 (8.3) 13.9 (8.6)
3rd 22.5 (14.0) 23.0 (14.3)
4th 36.1 (22.4) 35.2 (21.9)
Turning radius* mm (ft.in)
(Outside corner of bucket)
Articulation angle (each) degree 40 40
DIMENSIONS*: mm (ft.in)
ENGINE:
Model KOMATSU KOMATSU
S6D140E-2 SA6D170E
No. of cylinders- mm (in) 6-140 x 165 6-170 x 170
bore x stroke (5.5 x 6.5) (6.69 x 6.69)
Piston displacement ltr. (cu.in) 15.2 (930) 23.15 (1413)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 465 (122.9) 670 (177)
* See PERFORMANCE DATA
*6 Germany source
*7 China source
3A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg (lb)
Tires/Bucket I
2575
12.5/70-16-6PR(L-2)
(5680)
Unit: mm (ft.in)
Tires 12.5/70-16PR(L-2)
Tread 1180 (3'10")
45 Width over tires 1945 (5'9")
K J A Wheelbase 1750 (5'9")
B B Hinge pin height, max. height 2680 (8'10")
F
H C Hinge pin height, carry position
D Ground clearance 270 (10.6")
47
C D
E E Hitch height 750 (2'6")
10 F Overall height, ROPS canopy 2700 (8'10")
A
L
FVBH0007
3A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg (lb)
Tires/Bucket I
3475
15.5/70-18-8PR(L-2)
(7660)
Unit: mm (ft.in)
Tires 12.5/70-16PR(L-2)
Tread 1180 (3'10")
45 Width over tires 1945 (5'9")
K J A Wheelbase 1750 (5'9")
B B Hinge pin height, max. height 2680 (8'10")
F
H C Hinge pin height, carry position
D Ground clearance 270 (10.6")
47
C D
E E Hitch height 750 (2'6")
10 F Overall height, ROPS canopy 2700 (8'10")
A
L
FVBH0007
3A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Operating Width Over Ground Vertical Change in
Straight Full Turn Tire Clearance Reach
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in mm ft.in
14.00-24-12PR (L2) +130 +287 +95 +209 +85 +187 2185 7’2” 425 1’5” +25 +1.0” –25 –1.0”
15.5-25-8PR (L2) +10 +22 +10 +22 +5 +11 2180 7’2” 390 1’3” –10 –0.4” +10 +0.4”
17.5-25-12PR (L2) +150 +331 +110 +243 +95 +209 2220 7’3” 425 1’5” +25 +1.0” –25 –1.0”
Install ROPS canopy
–110 –243 –110 –243 –95 –209
(instead of cab)
Additional
+200 +441 +380 +838 +330 +728
counterweight
Air conditioner +70 +154 +80 +176 +70 +154
3A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground Change in
Operating Vertical
Weight Straight Full Turn Tire Clearance Dimensions Reach
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in mm ft.in
17.5-25-12PR (L3) +105 +231 +80 +176 +70 +154 2375 7’10” 425 1’5” 0 0” 0 0”
20.5-25-12PR (L2) +450 +992 +240 +529 +220 +485 2470 8’1” 495 1’8” +70 +2.8” –75 –3.0”
20.5-25-12PR (L3) +665 +1466 +355 +783 +320 +705 2470 8’1” 495 1’8” +70 +2.8” –75 –3.0”
Install ROPS canopy
–250 –551 –250 –551 –220 –485
(instead of cab)
Additional +300 +661 +590 +1301 +510 +1124
counterweight
Air conditioner +70 +154 +60 +132 +50 +110
3A-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground Change in
Operating Vertical
Straight Full Turn Tire Clearance Reach
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in mm ft.in
17.5-25-12PR (L3) +105 +231 +65 +143 +60 +132 2375 7’10” 425 1’5” 0 0” 0 0”
20.5-25-12PR (L2) +320 +705 +200 +441 +175 +386 2470 8’1” 495 1’8” +70 +2.8” –75 –3.0”
20.5-25-12PR (L3) +470 +1036 +300 +661 +260 +573 2470 8’1” 495 1’8” +70 +2.8” –75 –3.0”
Install ROPS canopy
–250 –551 –215 –474 –185 –408
(instead of cab)
Air conditioner +70 +154 +50 +110 +45 +99
3A-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground Change in
Operating Vertical
Weight Straight Full Turn Tire Clearance Dimensions Reach
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in mm ft.in
17.5-25-16PR (L3) +55 +121 +45 +99 +35 +77 2375 7’10” 395 1’4” 0 0” 0 0”
20.5-25-12PR (L2) +280 +617 +215 +474 +190 +419 2470 8’1” 465 1’6” +70 +2.8” –70 –2.8”
20.5-25-12PR (L3) +430 +948 +325 +717 +280 +617 2470 8’1” 465 1’6” +70 +2.8” –70 –2.8”
Install ROPS canopy
–250 –551 –250 –551 –220 –485
(instead of cab)
Additional +300 +661 +580 +1279 +510 +1124
counterweight
Air conditioner +70 +154 +50 +110 +40 +88
3A-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground Change in
Operating Vertical
Weight Straight Full Turn Tire Clearance Dimensions Reach
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in mm ft.in
17.5-25-16PR (L3) +55 +121 +35 +77 +30 +66 2375 7’10” 395 1’4” 0 0” 0 0”
20.5-25-12PR (L2) +225 +496 +140 +309 +120 +265 2470 8’1” 465 1’6” +70 +2.8” –70 –2.8”
20.5-25-12PR (L3) +375 +827 +235 +518 +205 +452 2470 8’1” 465 1’6” +70 +2.8” –70 –2.8”
Install ROPS canopy
–250 –551 –200 –441 –180 –397
(instead of cab)
Air conditioner +70 +154 +50 +110 +40 +88
3A-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground
Operating Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
20.5-25-12PR (L2) –160 –353 –120 –265 –104 –229 2585 8’6” 425 1’5” 0 0”
Install ROPS canopy (instead of cab) –150 –331 –107 –236 –93 –205
Additional counterweight +520 +1146 +1010 +2227 +880 +1940
Air conditioner +70 +154 +90 +198 +80 +176
3A-24
AH_25.book Page 25 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS cab –310 (–683) –280 (–620) –245 (–540)
Install additional counterweight 325 kg (715 lb) +325 (+715) +830 (+1830) +690 (+1520)
Unit: mm (ft.in)
20.5-25 tires
Tread 2050 (6'9")
45 Width over tires 2585 (8'6")
K A Wheelbase 3030 (9'11")
J
B
F G B Hinge pin height, max. height 3885 (12'9")
H
48 C Hinge pin height, carry position 450 (1'6")
E
C D D Ground clearance 400 (1'4")
A E Hitch height 1190 (3'11")
L
FVBH0030
F Overall height, top of the stack 3235 (10'6")
G Overall height, ROPS cab 3335 (10'11")
3A-25
AH_25.book Page 26 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Apply the following weight changes to operating weight and static tipping load.
Weight Changes
Change in Change in Tipping Load Change in
Operating Width Over Ground Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
20.5-25-16PR (L3) 0 0 0 0 0 0 2695 8’10” 390 1’3” 0 0”
23.5-25-16PR (L3) +1080 +2381 +740 +1632 +650 +1433 2780 9’1” 460 1’6” +65 2.6”
Remove ROPS cab –660 –1455 –650 –1433 –625 –1378
Install front/rear compartment +120 +265 +120 +265 +115 +254
Install additional counterweight +325 +717 +860 +1896 +715 +1577
3A-26
AH_25.book Page 27 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Apply the following weight changes to operating weight and static tipping load.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground
Operating Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
20.5-25-16PR (L3) 0 0 0 0 0 0 2695 8’10” 390 1’3” 0 0”
23.5-25-16PR (L3) +1080 +2381 +740 +1632 +650 +1433 2780 9’1” 460 1’6” +65 +2.6”
Remove ROPS cab –660 –1455 –650 –1433 –625 –1378
Install front/rear compartment +120 +265 +120 +265 +115 +254
Install additional counterweight +325 +717 +860 +1896 +715 +1577
3A-27
AH_25.book Page 28 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS cab –670 (–1475) –610 (–1345) –590 (–1300)
Install additional counterweight 325 kg (715 lb) +325 (+715) +830 (+1835) +690 (+1520)
3A-28
AH_25.book Page 29 Tuesday, March 23, 2004 9:41 AM
3A-29
AH_25.book Page 30 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS cab –670 (–1475) –600 (–1325) –580 (–1280)
Install additional counterweight +325 (+715) +835 (+1840) +700 (+1545)
3A-30
AH_25.book Page 31 Tuesday, March 23, 2004 9:41 AM
3A-31
AH_25.book Page 32 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Apply the following weight changes to operating weight and static tipping load.
Weight Changes
Change in Change in Tipping Load Width Over Ground Change in
Operating Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
23.5-25-16PR (L3) 0 0 0 0 0 0 2820 9’3” 460 1’6” 0 0”
26.5-25-16PR (L3) +420 +925 +330 +730 +290 +640 2940 9’8” 525 1’9” +65 +2.6”
Remove ROPS cab –660 –1455 –635 –1400 –605 –1335
Install front/rear compartment +120 +265 +115 +255 +110 +245
Install additional counterweight +325 +715 +880 +1940 +735 +1620
3A-32
AH_25.book Page 33 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Apply the following weight changes to operating weight and static tipping load.
3A-33
AH_25.book Page 34 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
23.5-25 tires 26.5-25 tires
Tread 2300 (7'7") 2300 (7'7")
45
Width over tires 2920 (9'7") 3010 (9'11")
K
J A Wheelbase 3450 (11'4") 3450 (11'4")
B
F G
B Hinge pin height, max. height 4805 (15'10") 4870 (16')
H
50
C Hinge pin height, carry position 730 (2'5") 730 (2'5")
C
E D Ground clearance 460 (1'6") 525 (1'9")
D
A
E Hitch height 1175 (3'10") 1240 (4'1")
L F Overall height, top of the stack 3015 (9'11") 3080 (10'2")
G Overall height, ROPS cab 3395 (11'2") 3460 (11'5")
3A-34
AH_25.book Page 35 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS cab –670 (–1475) –600 (–1325) –580 (–1280)
Install additional counterweight +400 (+885) +1010 (+2220) +845 (+1865)
3A-35
AH_25.book Page 36 Tuesday, March 23, 2004 9:41 AM
3A-36
AH_25.book Page 37 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Apply the following weight changes to operating weight and static tipping load.
3A-37
AH_25.book Page 38 Tuesday, March 23, 2004 9:41 AM
3A-38
AH_25.book Page 39 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg/lb
Tires/Buckets I II III IV
28220 28610 28410 27910
26.5-25-20PR (L-3) 62210 63070 62630 61530
28770 29160 28960 28460
29.5-25-22PR (L-3) 63430 64290 63850 62750
28620 29010 28810 28310
26.5-25-20PR (L-4)
63100 63960 63520 62420
26.5-25-20PR (L-5) 28980 29370 29170 28670
63890 64750 64310 63210
29.5-25-28PR (L-4) 29310 29700 29500 29000
64620 65480 65040 63940
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS cab –585 (–1290) –510 (–1125) –490 (–1080)
Remove steel cab –460 (–1015) –400 (–880) –385 (–850)
Remove front half fender –45 (–100) –14 (–30) –14 (–30)
Remove teeth –315 (–690) –415 (–910) –415 (–915)
Install additional counterweight +1000 (+2205) +2400 (+5290) +2000 (+4410)
3A-39
AH_25.book Page 40 Tuesday, March 23, 2004 9:41 AM
3A-40
AH_25.book Page 41 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
29.5-25 tires
Tread 2400 (7'20")
45 Width over tires 3190 (10'6")
K A Wheelbase 3600 (11'10")
J
B
F G B Hinge pin height, max. height 4905 (16'1")
H
48 C Hinge pin height, carry position 565 (1'10")
E
C D D Ground clearance 450 (1'5")
A E Hitch height 1240 (4'1")
L
FVBH0030
F Overall height, top of the stack 3635 (11'11")
G Overall height, ROPS canopy 3860 (12'8")
3A-41
AH_25.book Page 42 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –800 (–1760) –700 (–1540) –615 (–1360)
Remove steel cab –430 (–950) –310 (–680) –275 (–610)
Remove teeth –372 (–820) –475 (–1050) –475 (–1050)
Install additional counterweight +1000 (+2200) +2300 (+5070) +2030 (+4480)
3A-42
AH_25.book Page 43 Tuesday, March 23, 2004 9:41 AM
3A-43
AH_25.book Page 44 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
35/65-33 tires
Tread 2650 (8'8")
Width over tires 3570 (11'9")
45
K A Wheelbase 4100 (13'5")
J
B B Hinge pin height, max. height 5770 (18'11")
F G
H C Hinge pin height, carry position 670 (2'2")
48
E D Ground clearance 495 (1'7")
C D
E Hitch height 1385 (4'7")
A
L F Overall height, top of the stack 4125 (13'6")
FVBH0030
G Overall height, ROPS canopy 4250 (13'11")
Overall height, ROPS and cab 4250 (13'11")
3A-44
AH_25.book Page 45 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
35/65-33 tires
Tread 2650 (8'8")
Width over tires 3570 (11'9")
45
K A Wheelbase 4100 (13'5")
J
B B Hinge pin height, max. height 4850 (15'11")
F G
H C Hinge pin height, carry position 670 (2'2")
48
E D Ground clearance 495 (1'7")
C D
E Hitch height 1385 (4'7")
A
L F Overall height, top of the stack 4125 (13'6")
FVBH0030 G Overall height, ROPS canopy 4250 (13'11")
Overall height, ROPS and cab 4250 (13'11")
Measured with 35/65-33 tires
Buckets I II III
H.Dumping clearance, max. height and 45° dump angle** 2920 (9'7")
J. Reach at max. height and 45° dump angle** 2105 (6'11")
K. Operating height (fully raised) 7065 (23'2")
L. Overall length 11395 (37'5")
Turning radius* 8225 (27'0")
0° 105 (4.1")
Digging depth
10° 505 (1'8")
* Bucket at carry, outside corner of bucket.
** At the end of teeth or B.O.C.
3A-45
AH_25.book Page 46 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
35/65-33 tires
Tread 2650 (8'8")
Width over tires 3570 (11'9")
K A Wheelbase 4100 (13'5")
J
B
43˚ B Hinge pin height, max. height 4850 (15'11")
FG
H C Hinge pin height, carry position 670 (2'2")
C E D Ground clearance 495 (1'7")
D
E Hitch height 1385 (4'7")
A F Overall height, top of the stack 4125 (13'6")
FVBH0107
G Overall height, ROPS canopy 4250 (13'11")
Overall height, ROPS and cab 4250 (13'11")
NOTE:
a) It forbids riding over obstacle during stone handling (Allowable riding over height must be 50 mm (2") or
less).
b) Travel speed is set only to 1st gear during stone handling.
3A-46
AH_25.book Page 47 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –1050 (–2315) –965 (–2130) –850 (–1870)
Remove steel cab –430 (–950) –315 (–690) –275 (–610)
Remove teeth and adapter –890 (–1960) +1150 (+2535) +1005 (+2220)
Unit: mm (ft.in)
40/65-39-36PR 45/65-R39
(L-5) tires (L-5) tires
Tread 3000 (9'10") 3060 (10')
45
Width over tires 4040 (13'3") 4160 (13'8")
K A Wheelbase 4800 (15'9") 4800 (15'9")
J
50
B Hinge pin height, max. height 5990 (19'8") 6035 (19'10")
B
H FG C Hinge pin height, carry position 720 (2'4") 765 (2'6")
E D Ground clearance 540 (1'9") 585 (1'11")
C D E Hitch height 1530 (5') 1575 (5'2")
A
L
F Overall height, top of the stack 4825 (15'10") 4870 (16')
FVBH0019
G Overall height, ROPS canopy 4790 (15'9") 4835 (15'10")
3A-47
AH_25.book Page 48 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
40/65-39-36 PR (L-5) tires
Tread 3000 (9'10")
45
Width over tires 4040 (13'3")
K A Wheelbase 4800 (15'9")
J
50 B Hinge pin height, max. height 6550 (21'6")
B
H FG C Hinge pin height, carry position 720 (2'4")
E D Ground clearance 540 (1'9")
C D E Hitch height 1545 (5'1")
A
L F Overall height, top of the stack 4580 (15')
FVBH0019
G Overall height, ROPS and cab 4790 (15'9")
3A-48
AH_25.book Page 49 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –1385 (–3055) –1220 (–2690) –1180 (–2600)
Remove steel cab –430 (–950) –335 (–740) –330 (–730
Install additional couinter weight +1600 (+3530) +3850 (+8490) +3400 (+7500)
Unit: mm (ft.in)
45/65-45 tires
Tread 3350 (11')
45
Width over tires 4585 (15'1")
K A Wheelbase 5450 (17'11")
J
50 B Hinge pin height, max. height 6785 (22'3")
B
H FG C Hinge pin height, carry position 850 (2'9")
E D Ground clearance 550 (1'10")
C D E Hitch height 1390 (4'7")
A
L F Overall height, top of the stack 5080 (16'8")
FVBH0019
G Overall height, ROPS and cab 5275 (17'4")
3A-49
AH_25.book Page 50 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –1385 (–3055) –1220 (–2690) –1180 (–2600)
Remove steel cab –430 (–950) –335 (–740) –330 (–730)
Install additional couinter weight +1600 (+3530) +3850 (+8490) +3400 (+7500)
Unit: mm (ft.in)
45/65-45 tires
Tread 3350 (11')
45
Width over tires 4585 (15'1")
K A Wheelbase 5450 (17'11")
J
50 B Hinge pin height, max. height 7265 (23'10")
B
H FG C Hinge pin height, carry position 850 (2'9")
E D Ground clearance 550 (1'10")
C D E Hitch height 1390 (4'7")
A
L F Overall height, top of the stack 5080 (16'8")
FVBH0019
G Overall height, ROPS and cab 5275 (17'4")
3A-50
AH_25.book Page 51 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –1385 (–3055) –1220 (–2690) –1180 (–2600)
Remove steel cab –430 (–950) –335 (–740) –330 (–730)
Install additional couinter weight +1600 (+3530) +3850 (+8490) +3400 (+7500)
Unit: mm (ft.in)
45/65-45 tires
Tread 3350 (11')
45
Width over tires 4585 (15'1")
K A Wheelbase 5450 (17'11")
J
50 B Hinge pin height, max. height 6140 (20'2")
B
H FG C Hinge pin height, carry position 850 (2'9")
E D Ground clearance 550 (1'10")
C D E Hitch height 1390 (4'7")
A
L F Overall height, top of the stack 5080 (16'8")
FVBH0019
G Overall height, ROPS and cab 5275 (17'4")
3A-51
AH_25.book Page 52 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –1385 (–3055) –1220 (–2690) –1180 (–2600)
Remove steel cab –430 (–950) –335 (–740) –330 (–730)
Unit: mm (ft.in)
45/65-45-Tires
Tread 3350 (11')
45
Width over tires 4585 (15'1")
K A Wheelbase 5450 (17'11")
J
50 B Hinge pin height, max. height 6960 (22'10")
B
H FG C Hinge pin height, carry position 800 (2'7")
E D Ground clearance 550 (1'10")
C D E Hitch height 1300 (4'3")
A
L F Overall height, top of the stack 5080 (16'8")
FVBH0019
G Overall height, ROPS and cab 5275 (17'4")
3A-52
AH_25.book Page 53 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Remove ROPS canopy –1385 (–3055) –1220 (–2690) –1180 (–2600)
Remove steel cab –430 (–950) –335 (–740) –330 (–730)
Unit: mm (ft.in)
45/65-45-Tires
Tread 3350 (11')
45
Width over tires 4585 (15'1")
K A Wheelbase 5450 (17'11")
J
50 B Hinge pin height, max. height 7445 (24'5")
B
H FG C Hinge pin height, carry position 800 (2'7")
E D Ground clearance 550 (1'10")
C D E Hitch height 1390 (4'7")
A
L F Overall height, top of the stack 5080 (16'8")
FVBH0019
G Overall height, ROPS and cab 5275 (17'4")
3A-53
AH_25.book Page 54 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
55/80-57 tires 65/65-57 tires
Tread 4300 (14'1") 4300 (14'1")
45
Width over tires 5710 (18'9") 5970 (18'9")
K A Wheelbase 7100 (23'4") 7100 (23'4")
J
50 B Hinge pin height, max. height 8830 (29') 8895 (29'2")
B
H FG C Hinge pin height, carry position 1150 (3'9") 1150 (3'9")
E D Ground clearance 650 (2'2") 715 (2'4")
C D E Hitch height 1310 (4'4") 1375 (4'6")
A
L F Overall height, top of the stack 6630 (21'9") 6695 (22')
FVBH0019
G Overall height, ROPS and cab 6865 (22'6") 6930 (22'9")
3A-54
AH_25.book Page 55 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
55/80-57 tires 65/65-57 tires
Tread 4300 (14'1") 4300 (14'1")
45
Width over tires 5710 (18'9") 5970 (18'9")
K A Wheelbase 7100 (23'4") 7100 (23'4")
J
50 B Hinge pin height, max. height 9480 (31'1") 9545 (31'4")
B
H FG C Hinge pin height, carry position 1150 (3'9") 1150 (3'9")
E D Ground clearance 650 (2'2") 715 (2'4")
C D E Hitch height 1310 (4'4") 1375 (4'6")
A
L F Overall height, top of the stack 6630 (21'9") 6695 (22')
FVBH0019
G Overall height, ROPS and cab 6865 (22'6") 6930 (22'9")
3A-55
AH_25.book Page 56 Tuesday, March 23, 2004 9:41 AM
Weight Changes
Change in Operating Weight Change in Tipping Load kg (lb)
Tires & Options kg (lb) Straight Full Turn
Additional Counterweight (removed) –280 (–620) –530 (–1170) –460 (–1010)
ROPS Cab (removed)
ROPS Canopy (instead of ROPS Cab) –180 (–400) –170 (–375) –150 (–330)
Bucket Teeth (instead of bolt-on cutting edge)
15.5-25-12PR (L2) tubeless tires
15.5-25-12PR (L3) tubeless tires
17.5-25-12PR (L2) tubeless tires 0 0 0
17.5-25-12PR (L3) tubeless tires
3A-56
AH_25.book Page 57 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight, air
conditioning and operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground
Operating Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
17.5/25-12PR (L2) –450 –992 –240 –529 –220 –485 2375 7’10” 425 1’5” –70 –2.8”
17.5/25-12PR (L3) –345 –761 –160 –353 –150 –331 2375 7’10” 425 1’5” –70 –2.8”
20.5/25-12PR (L2) 0 0 0 0 0 0 2470 8’1” 495 1’8” 0 0”
20.5/25-12PR (L3) +215 +474 +115 +254 +100 +220 2470 8’1” 495 1’8” 0 0”
Install ROPS canopy (instead of cab) –250 –551 –250 –551 –220 –485
Remove additional counterweight –300 –661 –590 –1300 –510 –1124
Remove air conditioner –70 –154 –60 –132 –50 –110
3A-57
AH_25.book Page 58 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Ground
Operating Vertical
Straight Full Turn Over Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
17.5/25-12PR (L2) –330 –727 –286 –631 –249 –549 2380 7’10” 395 1’4” –70 –2.8”
17.5/25-12PR (L3) –290 –641 –252 –556 –219 –483 2380 7’10” 395 1’4” –70 –2.8”
20.5/25-12PR (L3) +90 +199 +78 +172 +68 +150 2470 8’1” 457 1’6” 0 0”
Install ROPS canopy (instead of cab) –331 –730 –287 –632 –249 –550
3A-58
AH_25.book Page 59 Tuesday, March 23, 2004 9:41 AM
Fork Bucket
Static tipping load Bucket Type Stockpile
– boom level Straight kg (lb) 6855 (15,113) Bucket
Fork level, 610 Heaped m 3 (yd3) 1.9 (2.5)
mm (24”) load Full turn (40°) kg (lb) 5963 (13,146) Bucket capacity
center Struck m 3 (yd3) 1.6 (2.1)
Operating weight kg (lb) 12061 (26,590) Bucket width mm (ft.in) 2685 (8'10")
Bucket weight kg (lb) 981 (2,163)
Fork tine length mm (in) 1525 (60")
Straight kg (lb) 8800 (19,417)
Ground to top of tine at maximum lift mm (ft.in) 3820 (12'6") Static tipping load
Full turn (40°) kg (lb) 7750 (17,086)
Reach at maximum lift mm (ft.in) 750 (2'5")
Dumping clearance, max. height and
Ground to top of tine – boom and tine mm (ft.in) 2905 (9'6")
mm (ft.in) 1820 (5'11") 45° dump angle
level
Reach at 2130 mm (7') and 45° dump
Reach boom and tine level mm (ft.in) 1660 (5’5”) mm (ft.in) 1632 (5'4")
angle
Overall length – tine level on ground mm (ft.in) 8055 (26’5") Reach with boom/bucket level mm (ft.in) 2469 (8'1")
Operating load kg (lb) 2982 (6,574) Operating height (fully raised) mm (ft.in) 5195 (17'0")
Bucket on ground mm (ft.in) 7310 (24'0")
• Operating load per SAE J1197 (Feb. 1991), 50% of static Overall length
tipping load. Bucket at carry mm (ft.in) 7255 (23’10”)
• Static tipping load and operating weight shown include 0° mm (ft.in) 112 (4.4")
Digging depth
lubricant, coolant, full fuel tank, ROPS cab, 20.5/25-12PR 10° mm (ft.in) 325 (1’1")
(L2) tires, front fenders, and operator. Breakout force kg (lb) 11100 (24,581)
• Machine stability and operating weight affected by Operating weight kg (lb) 12455 (27,459)
counterweight, tire size, and other attachments.
• Note the following weight changes to operating weight and • All dimensions, weights, and performance values based on
static tipping loads. SAE J732c and J742b standards (bucket only).
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground
Operating Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
17.5-25-12PR (L3) –290 –641 –205 –452 –178 –393 2380 7’10” 395 1’4” –70 –2.8”
20.5-25-12PR (L3) +90 +199 +64 +141 +56 +123 2470 8’1” 457 1’6” 0 0”
Install ROPS canopy (instead of cab) –331 –730 –234 –516 –203 –449
3A-59
AH_25.book Page 60 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in Change in Tipping Load Change in
Width Over Ground
Operating Vertical
Straight Full Turn Tire Clearance
Weight Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
20.5-25-12PR (L3) +160 +353 +120 +265 +104 +229 2585 8’6” 425 1’5” 0 0
Install ROPS canopy (instead of cab) –150 –331 –107 –239 –93 –205
Remove additional counterweight –520 –1146 –1070 –2359 –940 –2072
* 520kg (1150lb) ballast used instead of additional counterweight
** 675kg (1490lb) ballast used instead of additional counterweight
3A-60
AH_25.book Page 61 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Operating Weight Tipping Load Straight Tipping Load Full Turn
kg lb kg lb kg lb
Remove ROPS cab –660 –1,455 –650 –1,433 –625 –1,378
Remove additional counterweight –325 –717 –860 –1,896 –715 –1,577
Install ROPS canopy +430 +950 +425 +937 +410 +904
3A-61
AH_25.book Page 62 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Operating Weight Tipping Load Straight Tipping Load Full Turn
kg lb kg lb kg lb
Remove ROPS cab –660 –1,455 –650 –1,433 –625 –1,378
Remove additional counterweight –325 –717 –885 –1,951 –755 –1,661
Install ROPS canopy +430 +950 +425 +937 +410 +904
3A-62
AH_25.book Page 63 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Ground Change in
Operating Tipping Load Tipping Load
Width over tires vertical
Tires Weight Straight Full Turn clearance
dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
26.5-25-20PR (L-4) +425 +937 +330 +728 +290 +639 3010 9'11" 525 1'9" +65 +2.6"
Remove ROPS cab –660 –1455 –610 –1345 –590 –1300
Install ROPS canopy +430 +950 +360 +795 +345 +760
Remove additional
–400 –880 –950 –2094 –790 –1742
counterweight
3A-63
AH_25.book Page 64 Tuesday, March 23, 2004 9:41 AM
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, ROPS cab, additional counterweight and
operator.
• Machine stability and operating weight affected by counterweight, tire size, and other attachments.
Weight Changes
Change in
Operating Tipping Load Tipping Load Width Ground Vertical
Weight Straight Full Turn Over Tire Clearance
Dimensions
kg lb kg lb kg lb mm ft.in mm ft.in mm ft.in
Tires: 26.5-25-20PR (L-4) +360 +794 +250 +551 +220 +485 3010 9'11" 525 1'9" 0 0
Remove ROPS cab –660 –1455 –550 –1213 –530 –1168
Install ROPS canopy +430 +950 +360 +795 +345 +760
Remove additional counterweight –400 –880 –950 –2094 –790 –1742
3A-64
AH_25.book Page 65 Tuesday, March 23, 2004 9:41 AM
All specs. are with teeth and 29.5-25-22/PR(L-3) tires, steel cab, ROPS canopy, lubricant, full fuel and
operator.
Standard Boom
Loose Material Highlift Boom
Bucket Type General Purpose Straight Edge General Purpose
Straight Edge
w/Bolt On Straight Edge
w/B.O.C. Cutting Edge W/BOCE
SAE Rated m3 (cu.yd) 5.0 (6.5) 5.5 (7.2) 4.28 (5.6)
Bucket Capacity
Struck m3 (cu.yd) 4.6 (6.0) 5.1 (6.6) 3.6 (4.7)
Bucket Width mm (ft.in) 3400 (11'2") 3400 (11'2") 3400 (11'2")
Bucket Weight kg (lb) 2760 (6,072) 2923 (6,445) 2190 (4,828)
Straight kg (lb) 24000 (52,920) 23728 (52,322) 21765 (47,984)
Static Tipping Load
Full turn (40°) kg (lb) 20602 (45,427) 20376 (44,928) 18800 (41,447)
Dumping clearance, max. height and 45° dump angle mm (ft.in) 3170 (10'5") 3095 (10'2") 3700 (12'2")
Reach at 2130 mm (7') cutting edge clearance and
mm (ft.in) 2025 (6'8") 2108 (6'11") 2430 (8'0")
45° dump angle
Reach at max. height and 45° dump angle mm (ft.in) 1365 (4'6") 1448 (4'9") 1448 (4'9")
Height to hinge pin (fully raised) mm (ft.in) 3760 (12'4") 3910 (12'10") 3890 (12'9")
Operating Height (fully raised) mm (ft.in) 6175 (20'3") 6198 (20'4") 6520 (21'5")
Overall Length Bucket at carry mm (ft.in) 9105 (29'10") 9195 (30'2") 9790 (32'1")
Turning Radius (bucket at carry, outside corner of
mm (ft.in) 7315 (24') 7366 (24'2") 7390 (24'2")
bucket)
0° mm (ft.in) 150 (6") 94 (3.7") 145 (5.7")
Digging Depth
10° mm (ft.in) 375 (1'3") 384 (15.1") 365 (14.4")
Breakout Force kg (lb) 23700 (52,259) 21542 (47,500) 28450 (62,721)
Operating Weight** kg (lb) 30440 (67,120) 30609 (67,493) 30665 (67,605)
• Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers. SAE
standard J-732 and J-742b.
• Static tipping load and operating weight shown include lubricants, coolant, full fuel tank, ROPS cab, front fenders, optional
counterweight, 29.5-25-22PR (L3) tubeless tires and operator.
• Machine stability and operating weight are affected by counterweight, tire size and other attachments.
Do not use tire ballast with optional counterweight.
• B.O.C.= Bolt on Cutting Edge
Weight Changes
Change in Operating Weight Change in Tipping Load kg (lb)
Tires & Options
kg (lb) Straight Full Turn
Remove Steel Cab –305 (–670) –260 (–570) –250 (–550)
Deduct Additional Counterweight –1000 (–2200) –2400 (–5280) –2000 (–4400)
3A-65
AH_25.book Page 66 Tuesday, March 23, 2004 9:41 AM
Unless otherwise indicated, specs are with teeth and 35/65-33, 24PR (L4) tires, steel cab, ROPS canopy,
lubricant, full fuel, optional counterweight, and operator.
Standard Boom High Lift Boom Load and Carry
Bucket Type Spade Nose Straight Edge Spade Nose
With Teeth With BOCE With Teeth
SAE rated m3 (yd3) 6.1 (8.0) 5.6 (7.3) 7.5 (9.8)
Bucket capacity
Struck m3 (yd3) 5.1 (6.7) 4.9 (6.4) 6.8 (8.9)
Bucket width mm (ft.in) 3685 (12'1") 3685 (12'1") 3685 (12'1")
Bucket weight kg (lb) 4270 (9,411) 4005 (8,830) 5075 (11,185)
Straight kg (lb) 33300 (74,414) 29400 (64,816) 38900 (85,760)
Static tipping load
Full turn (40°) kg (lb) 29410 (64,838) 25900 (57,100) 34300 (75,619)
Dumping clearance, max. height and 45° mm (ft.in) 3530 (11'7") 4460 (14’8”) 2920 (9'7")
dump angle
Reach at 2130 mm (7') cutting edge
mm (ft.in) 2790 (9'2") 2861 (9'5") 2580 (8'6")
clearance and 45° dump angle
Reach at max. height and 45° dump angle mm (ft.in) 1990 (6'6") 1505 (4'11") 2105 (6'11")
Reach with boom horizontal and bucket
level mm (ft.in) 3830 (12'7") 3643 (11'11") 3815 (12'6")
Operating height (fully raised) mm (ft.in) 7165 (23'6") 7720 (25'4") 7065 (23'2")
Bucket at ground mm (ft.in) 11404 (37'5") 11369 (37'4") 11404 (37'5")
Overall length
Bucket at carry mm (ft.in) 11196 (36'9") 11585 (38'0") 11395 (35'5")
Turning radius* mm (ft.in) 8260 (27'1") 8850 (29’0”) 8225 (27'0")
0° mm (ft.in) 50 (2") 130 (5") 105 (4")
Digging depth
50° mm (ft.in) 470 (1’6") 410 (1’4") 505 (1'8")
Breakout force (bucket cylinder) kg (lb) 37653 (83,010) 42550 (98,216) 35400 (78,022)
Operating weight kg (lb) 46200 (101,854) 46300 (102,074) 49400 (108,908)
* Turning radius measured with bucket at carry position, outside corner of bucket.
• Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers. SAE
standard J732c and J742b.
• Static tipping load and operating weight shown include 35/65-33, 24PR (L4) tires, enclosed cab, ROPS canopy, lubricant, full fuel tank,
optional counterweight and operator.
• Machine’s stability and operating weight are affected by counterweight, tire size and other weight changes to operating weights
and static tipping load.
• Load and carry arrangement includes 35/65-33, 42PR tires.
Weight Change
Change in Change in Static Tipping Load for Standard Boom
Tires & Options Operating Weight Straight Full Turn
kg lb kg lb kg lb
Remove ROPS cab –800 –1764 –700 –1543 –615 –1356
35/65-33, 24PR (L5) tubeless tires +1140 +2510 +790 +1738 +695 +1565
35/65-33, 30PR (L5) tubeless tires +1275 +2805 +885 +1947 +780 +1720
35/65-R33 XLDD1 (L4) radials +240 +530 +162 +357 +126 +278
35/65-R33 XLDD2 (L5) radials +545 +1200 +366 +808 +287 +633
Remove counterweight –1000 –2200 –2300 –5072 –2030 –4466
• All dimensions, weights, and performance values based on SAE J732c and J742b standards.
3A-66
AH_25.book Page 67 Tuesday, March 23, 2004 9:41 AM
All specs are with teeth and 41.25/75-39, 34PR (L5) tires, steel cab, ROPS canopy, lubricant, full fuel,
optional counterweight, and operator.
Straight Edge Rock Spade Nose Rock Spade Nose Rock
Bucket Type With Teeth With Teeth With Teeth (HL)
SAE rated m3 (yd3) 8.7 (11.4) 8.7 (11.4) 8.0 (10.5)
Bucket capacity
Struck m3 (yd3) 7.6 (9.9) 7.6 (9.9) 7.0 (9.2)
Bucket width mm (ft.in) 4570 (15'0") 4570 (15'0") 4570 (15'0")
Bucket weight kg (lb) 6770 (14,925) 7150 (15,760) 6830 (15,080)
Straight kg (lb) 46830 (103,240) 46480 (102,600) 42330 (93,440)
Static tipping load
Full turn (40°) kg (lb) 41100 (90,610) 40770 (90,000) 36770 (81,170)
Dumping clearance, max. height and 45° mm (ft.in) 4320 (14'2") 4080 (13’5”) 4685 (15'4")
dump angle
Reach at 2130 mm (7') and 45° dump angle mm (ft.in) 2995 (9'10") 3210 (10'7") 3530 (11'7")
Reach at max. height and 45° dump angle mm (ft.in) 1890 (6'2") 2135 (7'0") 2120 (6'11")
Operating height (fully raised) mm (ft.in) 8210 (26'11") 8210 (26'11") 8665 (28'5")
Overall length Bucket ground mm (ft.in) 12140 (39'10") 12480 (40'11") 13295 (43'7")
Turning radius* mm (ft.in) 9620 (31'7") 9615 (31’6”) 9840 (32'3")
0° mm (ft.in) 130 (5") 130 (5") 145 (6")
Digging depth
10° mm (ft.in) 470 (1’7") 520 (1’8") 530 (1'9")
Breakout force (bucket cylinder) kg (lb) 64700 (142,640) 52700 (116,180) 55800 (123,180)
Operating weight kg (lb) 71020 (156,570) 71400 (157,410) 73000 (161,150)
* Turning radius measured with bucket at carry position, outside corner of bucket with teeth.
• Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers. SAE
standard J732 JUN 92 and J742 FEB 85.
• Static tipping load and operating weight shown include 41.25/75-39, 34PR (L5) tires, enclosed cab, ROPS canopy, lubricant, full fuel
tank, optional counterweight and operator.
• Machine’s stability and operating weight are affected by counterweight, tire size and other weight changes to operating weights
and static tipping load.
Weight Changes
Change in Static Tipping Load
Change in Operating Weight
Straight Full Turn (40°)
S/E With S/N With S/N With S/E With S/N With S/N With S/E With S/N With S/N With
Tires/Bucket
Teeth Teeth Teeth (HL) Teeth Teeth Teeth (HL) Teeth Teeth Teeth (HL)
kg 71500 71880 73480 47160 46810 42660 41400 41070 37070
45/65 R39 (L5)
(lb) (157,630) (158,470) (161,995) (103,970) (103,198) (94,049) (91,271) (90,543) (81,725)
3A-67
AH_25.book Page 68 Tuesday, March 23, 2004 9:41 AM
3A-68
AH_25.book Page 69 Tuesday, March 23, 2004 9:41 AM
3A-69
AH_25.book Page 70 Tuesday, March 23, 2004 9:41 AM
65
C R
E
d 47
a
c
b H
D 50
f F
e B
A
FVBH0008
3A-70
AH_25.book Page 71 Tuesday, March 23, 2004 9:41 AM
65
C R
E
d 47
a
c
b H
D 50
f F
e B
A
FVBH0008
3A-71
AH_25.book Page 72 Tuesday, March 23, 2004 9:41 AM
65
C R
E
d 47
a
c
b H
D 50
f F
e B
A
FVBH0008
3A-72
AH_25.book Page 73 Tuesday, March 23, 2004 9:41 AM
65
C R
E
d 47
a
c
b H
D 50
f F
e B
A
FVBH0008
3A-73
AH_25.book Page 74 Tuesday, March 23, 2004 9:41 AM
65
C R
E
d 47
a
c
b H
D 50
f F
e B
A
FVBH0008
3A-74
AH_25.book Page 75 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg/lb
Tires/Buckets I II III IV
455/70 R24 SPT 9 7455 (16435) 7735 (17055) 7560 (16665) 7800 (17195)
Weight Changes
Operating weight Tipping load straight Tipping load full turn Overall length
Tires & Options
kg lb kg lb kg lb mm inch
Additional counterweight +305 +670 +725 +1600 +520 +1150 — —
Equipment with teeth +100 +220 -60 -130 -115 -250 +225 8.9"
3A-76
AH_25.book Page 77 Tuesday, March 23, 2004 9:41 AM
Operating weight*
kg/lb
Tires/Buckets I II III IV V VI
20.5-R25 L3 14040 14255 14120 14325 14265 14475
(30950) (31430) (31130) (31580) (31450) (31910)
• All dimensions, weights and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, steel cab, ROPS canopy and operator.
• Machine stability and operating weight are affected by counterweight, tire size and other attachments.
Apply the following weight changes to operating weight and static tipping load.
Weight Changes Operating weight Tipping load straight Tipping load full turn Overall length (A)
kg lb kg lb kg lb mm ft.in
Add. counterweight
+520 +715 +920 +1896 +660 +1576 +146 +5.7
3A-77
AH_25.book Page 78 Tuesday, March 23, 2004 9:41 AM
3A-78
AH_25.book Page 79 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg/lb
Tires/Buckets I II III IV V VI VII VIII IX
23.5-R25 L3 17875 18090 17875 18090 17985 18200 18105 18320 18285
(39410) (39880) (39410) (39880) (39650) (40125) (39945) (40390) (40310)
Weight Changes Operating weight Tipping load straight Tipping load full turn Overall length (A)
kg lb kg lb kg lb mm ft.in
Add. counterweight
+325 +715 +860 +1896 +715 +1576 +146 +5.7
Equipment with teeth +100 +220 -100 -220 -110 -243 – –
3A-79
AH_25.book Page 80 Tuesday, March 23, 2004 9:41 AM
3A-80
AH_25.book Page 81 Tuesday, March 23, 2004 9:41 AM
Operating weight*
kg/lb
Tires/Buckets I II III IV V VI VII VIII IX X
19065 19290 19065 19290 19250 19470 19350 19575 19415 19515
750/65 R25
(42030) (42530) (42030) (42530) (42440) (42920) (42660) (43155) (42800) (43020)
• All dimensions, weights and performance values based on SAE J732c and J742b standards.
• Static tipping load and operating weight shown include lubricant, coolant, full fuel tank, steel cab, ROPS canopy and operator.
• Machine stability and operating weight are affected by counterweight, tire size and other attachments.
Apply the following weight changes to operating weight and static tipping load.
Weight Changes Operating weight Tipping load straight Tipping load full turn Overall length (A)
kg lb kg lb kg lb mm ft.in
Add. counterweight
+325 +715 +830 +1830 +700 +1545 +146 +5.7
Equipment with teeth +100 +220 -100 -220 -110 -243 – –
3A-81
AH_25.book Page 82 Tuesday, March 23, 2004 9:41 AM
3A-82
AH_25.book Page 83 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg/lb
Tires/Buckets I II III IV V VI VII VIII IX X
23135 22775 22975 23435 23425 23192 23195 23225 23535 23285
26.5-R25 L3
(51000) (50210) (50650) (51665) (51645) (51130) (51135) (51200) (51885) (51335)
Weight Changes Operating weight Tipping load straight Tipping load full turn Overall length (A)
kg lb kg lb kg lb mm ft.in
Add. counterweight
+400 +882 +1030 +2271 +860 +1896 +190 +7.5
Equipment with teeth +140 +309 -140 -309 -140 -309 – –
3A-83
AH_25.book Page 84 Tuesday, March 23, 2004 9:41 AM
3A-84
AH_25.book Page 85 Tuesday, March 23, 2004 9:41 AM
Operating weight
kg/lb
Tires/Bucket I II III IV V VI VII VIII IX X XI XII XIII
25755 25460 25653 25595 25788 25735 25928 25510 25703 25725 25913 25660 25860
26.5-R25 L3
(56780) (56130) (56555) (56425) (56850) (56735) (57160) (56240) (56665) (56715) (57130) (56570) (57010)
Weight Changes Operating weight Tipping load straight Tipping load full turn Overall length (A)
kg lb kg lb kg lb mm ft.in
Add. counterweight
+400 +882 +950 +2094 +790 +1742 +190 +7.5
Equipment with teeth +140 +309 -140 -309 -140 -309 – –
3A-85
AH_25.book Page 86 Tuesday, March 23, 2004 9:41 AM
3A-86
AH_25.book Page 87 Tuesday, March 23, 2004 9:41 AM
Capacity
Heaped Bucket width Bucket weight Breakout
m3 (cu.yd) mm (ft.in)* kg (lb) force kg (lb)
Operating weight
kg/lb
Tires/Bucket I II III IV V
29.5-R25 L3 29360 (64725) 29470 (64970) 29570 (65190) 29820 (65740) 30020 (66180)
Weight Changes Operating weight Tipping load straight Tipping load full turn Overall length (A)
kg lb kg lb kg lb mm ft.in
Add. counterweight
+1000 +2205 +1900 +4189 +1600 +3527 +141 +5.6
Tire inflation (29.5-R25) +1900 +4189 +2820 +62174 +2435 +5368 – –
Equipment with teeth +250 +551 -250 -551 -270 -595 – –
3A-87
AH_25.book Page 88 Tuesday, March 23, 2004 9:41 AM
Buckets I II III IV V
(Capacities in accordance with ISO 7546) 4.5 5.0 5.5 4.5 5.0
m3 (yd3) (5.9) (6.5) (7.2) (5.9) (6.5)
1274 1323 1415 1486 1535
a Reach at 45º mm (ft.in) (4'2") (4'4") (4'8") (4'11") (5')
b Dump height at 45º mm (ft.in) 3251 3195 3103 3039 2983
(10'8") (10'6") (10'2") (10') (9'9")
4496 4496 4496 4496 4496
c Hinge pin height mm (ft.in)
(14'9") (14'9") (14'9") (14'9") (14'9")
d Height top edge of bucket mm (ft.in) 6072 6160 6263 6229 6160
(19'11") (20'3") (20'7") (20'5") (20'3")
124 124 124 124 124
e Dig depth mm (ft.in) (4'9") (4'9") (4'9") (4'9") (4'9")
4105 4105 4105 4105 4105
f Overload height mm (ft.in)
(13'6") (13'6") (13'6") (13'6") (13'6")
9127 9197 9328 9427 9497
A Overal length, bucket grounded mm (ft.in)
(29'11") (30'2") (30'7") (30'11") (31'2")
3600 3600 3600 3600 3600
B Wheelbase mm (ft.in)
(11'10") (11'10") (11'10") (11'10") (11'10")
3460 3460 3460 3460 3460
C Bucket width mm (ft.in)
(11'4") (11'4") (11'4") (11'4") (11'4")
3190 3190 3190 3190 3190
D Width over tires mm (ft.in)
(10'6") (10'6") (10'6") (10'6") (10'6")
2400 2400 2400 2400 2400
E Track width mm (ft.in)
(7'10") (7'10") (7'10") (7'10") (7'10")
450 450 450 450 450
F Ground clearance mm (ft.in) (1'6") (1'6") (1'6") (1'6") (1'6")
G Width over stone deflectors mm (ft.in) – – – 3650 3650
(12') (12')
H Overal height mm (ft.in) 3860 3860 3860 3860 3860
(12'8") (12'8") (12'8") (12'8") (12'8")
3A-88
AH_25.book Page 89 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Steel ROPS cab –310 (–683)
Unit: mm (ft.in)
20.5-25 tires
Tread 2050 (6'9")
Width over tires 2585 (8'6")
45
K A Wheelbase 3030 (9'11")
J
B B Hinge pin height, max. height 3885 (12'9")
F G
H C Hinge pin height, carry position 450 (1'6")
48
E D Ground clearance 400 (1'4")
C D
E Hitch height 1190 (3'11")
A
L F Overall height, top of the stack 3205 (10'6")
FVBH0030
G Overall height, ROPS cab 3335 (10'11")
3A-89
AH_25.book Page 90 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Steel ROPS cab –310 (–683)
Unit: mm (ft.in)
23.5-25 tires
Tread 2160 (7'1")
Width over tires 2780 (9'1")
45
K A Wheelbase 3200 (10'6")
J
B B Hinge pin height, max. height 4095 (13'5")
F G
H C Hinge pin height, carry position
48
E D Ground clearance 455 (1'6")
C D
E Hitch height 1150 (3'9")
A
L F Overall height, top of the stack 3345 (11'0")
FVBH0030
G Overall height, steel cab 3380 (11'1")
3A-90
AH_25.book Page 91 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Steel ROPS cab –310 (–683)
Unit: mm (ft.in)
23.5-25 tires
Tread 2200 (7'3")
Width over tires 2820 (9'3")
45
K A Wheelbase 3300 (10'10")
J
B B Hinge pin height, max. height 4250 (13'11")
F G
H C Hinge pin height, carry position
48
E D Ground clearance 460 (1'6")
C D
E Hitch height 1175 (3'10")
A
L F Overall height, top of the stack 3340 (11'0")
FVBH0030
G Overall height, steel cab 3400 (11'2")
3A-91
AH_25.book Page 92 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Steel ROPS cab –310 (–683)
Unit: mm (ft.in)
26.5-25 tires
Tread 2300 (7'7")
Width over tires 3010 (9'11")
45
K A Wheelbase 3400 (11'2")
J
B B Hinge pin height, max. height 4355 (14'3")
F G
H C Hinge pin height, carry position
48
E D Ground clearance 525 (1'9")
C D
E Hitch height 1240 (4'1")
A
L F Overall height, top of the stack 3470 (11'5")
FVBH0030
G Overall height, steel cab 3490 (11'5")
3A-92
AH_25.book Page 93 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Steel ROPS cab
Unit: mm (ft.in)
26.5-25 tires
Tread 2400 (7'10")
Width over tires 3090 (10'2")
45
K A Wheelbase 3600 (11'10")
J
B B Hinge pin height, max. height 4455 (14'7")
F G
H C Hinge pin height, carry position
48
E D Ground clearance 405 (1'4")
C D
E Hitch height 1195 (3'11")
A
L F Overall height, top of the stack 3590 (11'9")
FVBH0030
G Overall height, steel cab 3815 (12'6")
3A-93
AH_25.book Page 94 Tuesday, March 23, 2004 9:41 AM
Weight Changes Change in operating weight kg (lb) Change in tipping load kg (lb)
Straight Full turn
Steel ROPS cab
Unit: mm (ft.in)
35/65-33 tires
Tread 2650 (8'8")
Width over tires 3570 (11'9")
45
K A Wheelbase 4100 (13'5")
J
B B Hinge pin height, max. height 5155 (16'11")
F G
H C Hinge pin height, carry position
48
E D Ground clearance 495 (1'7")
C D
E Hitch height 1295 (3'3")
A
L F Overall height, top of the stack 4125 (13'6")
FVBH0030
G Overall height, steel cab 4250 (13'11")
3A-94
AH_25.book Page 95 Tuesday, March 23, 2004 9:41 AM
Example:
Haul... Return...
Using the graph for the Loaded machine, read from Using the graph for the Empty machine, read from
the Travel Distance (one way) scale at 300 m (980 the Travel Distance (one way) scale at 400 m (1310
feet) across to the 6% total resistance line (point A). feet) across to the 2% total resistance line (point A).
From (point A) read down to the Travel Time (one From (point A) read down to the Travel Time (one
way) scale to determine haul time = 1.5 minutes. way) scale to determine haul time = 1.0 minutes
LOADED EMPTY
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
2%
TOTAL RESISTANCE
DISTANCE TRAVELED
700
TOTAL RESISTANCE
700
2000 4%
2000 600 600
2% 6%
500 4% 500
1500 1500 A
400m 8%
400 6% 400
6%
300m A 8% 1000 300 10%
1000 300
10%
15%
200 15% 200 20%
500 20% 500
100 100
1.5 1.0
0 0 0 0
0 0.5 1.0 1.5 2.0 (Minutes) 0 0.5 1.0 1.5 2.0 (Minutes)
TIME TIME
p
3A-95
AH_25.book Page 96 Tuesday, March 23, 2004 9:41 AM
WA500-3 LOADED
(feet) (m)
1000
3000 900
800
2500 2%
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 600
4%
500
1500
6%
400
8%
1000 300 10%
200 15%
500 20%
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0274
WA500-3 EMPTY
(feet) (m)
1000
3000 900 2%
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700 4%
2000 600
6%
500
1500 8%
400 10%
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0273
3A-96
AH_25.book Page 97 Tuesday, March 23, 2004 9:41 AM
WA600-3 LOADED
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700 2%
2000 600
500 4%
1500
400 6%
1000 300 8%
10%
200 15%
500 20%
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0276
WA600-3 EMPTY
(feet) (m)
1000
3000 900
2%
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 4%
600
6%
500
1500
400 8%
15%
200 20%
500
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0275
3A-97
AH_25.book Page 98 Tuesday, March 23, 2004 9:41 AM
WA700-3 LOADED
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
2%
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 600
500 4%
1500
6%
400
8%
1000 300 10%
200 15%
500 20%
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0278
WA700-3 EMPTY
(feet) (m)
1000
3000 900
2%
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
4%
2000 600
500 6%
1500
8%
400
10%
1000 300
15%
200 20%
500
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0277
3A-98
AH_25.book Page 99 Tuesday, March 23, 2004 9:41 AM
WA800-3 LOADED
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2%
2000 600
500 4%
1500
6%
400
1000 300 8%
10%
200 15%
500 20%
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0280
WA800-3 EMPTY
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
2%
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 600 4%
500
1500 6%
400
8%
1000 300 10%
15%
200
20%
500
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0279
3A-99
AH_25.book Page 100 Tuesday, March 23, 2004 9:41 AM
WA900-3 LOADED
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 2%
600
500
1500 4%
400
6%
1000 300 8%
10%
200 15%
500 20%
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0282
WA900-3 EMPTY
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
2%
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 600
4%
500
1500
6%
400
8%
1000 300 10%
15%
200
20%
500
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0281
3A-100
AH_25.book Page 101 Wednesday, March 24, 2004 2:57 PM
WA1200-3 LOADED
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 600
2%
500
1500
4%
400
1000 300 6%
8%
10%
200 15%
500 20%
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0284
WA1200-3 EMPTY
(feet) (m)
1000
3000 900
800
2500
(ROLLING PLUS GRADE)
DISTANCE TRAVELED
TOTAL RESISTANCE
700
2000 600 2%
500 4%
1500
400 6%
1000 300 8%
10%
15%
200 20%
500
100
0 0
0 0.5 1.0 1.5 2.0 (Minutes)
TIME
FVBH0283
3A-101
AH_25.book Page 102 Tuesday, March 23, 2004 9:41 AM
1. OPERATING WEIGHT
The total mass in kilograms (pounds) of the machine as specified and fully serviced, including a full fuel
tank and 80 kg (175 Ib) operator.
The struck capacity is defined as the volume of material retained in the bucket after a heaped load is
struck by drawing a straight edge across the width of bucket with one end of the straight edge resting on
the cutting edge and the other end resting on the uppermost portion of the bucket back sheet or spill
guard. The struck capacity (Vs) can be expressed by the following equation:
2 2
Vs = AW – ab
3
A = cross sectional area at the center of the TOP OF b
bucket, mm2 (in2.). SPILL b BIT W
GUARD 2
W = average inside width of the bucket, mm 2 2
1
(in.). HEAP 90 c 1
a
a = height of the spill guard at the center of
A
the bucket normal to the strike line, mm
(in.).
b = length of opening at the center of the
bucket, mm (in.). FVBH0009
b2 W b2
Vh = Vs + – (a+c)
8 6
Where c is the length on a normal to the strike line. On one end it is terminated by the assumed crest of
the material.
On the other end it is terminated by the intersection with a line from the bit or cutting edge tip to the base
of the spill guard.
This method applies primarily to irregular buckets having parallel sides and a cutting edge parallel to the
edge of the spill guard or back sheet. Moderately clipped spill guard corners will introduce no appreciable
errors.
3. RATED LOAD
The rated load (operating load) will not exceed 50% of the TIPPING LOAD for wheel loaders or 35% of the
TIPPING LOAD for crawler loaders, and will be considered as operating under the following conditions:
1. Lifting ability of the machine in all bucket positions to be no less than the specified operating load.
2. Bucket attachment of specified size and type.
3. Maximum travel speed of 6 km/h (3.7 mph).
4. Operating surface.
(a) Shall be hard, moderately smooth and level for wheel loaders.
(b) General operating conditions of crawler loaders are such that they normally are not operating on
hard, moderately smooth level surface.
For this reason, the rating on crawler loaders is set at the lower figure of 35%.
4. BREAKOUT FORCE
Breakout force in kilograms (and kilo-Newton or
pounds) is the maximum sustained vertical Breakout Force
upward force exerted 100 mm (4 in) behind the tip Bucket edge
of the bucket cutting edge and is achieved
through the ability to lift and/or roll-back the
4" (101.6mm)
bucket about the specified pivot point under the
following conditions:
Breakout force
(a) Machine with transmission in neutral. FVBH0010
(b) All brakes released.
(c) Unit at standard operating weight, rear of machine not tied down.
3A-102
AH_25.book Page 103 Tuesday, March 23, 2004 9:41 AM
(d) Bottom of cutting edge parallel to and not more than 25 mm (1 in) above or below the ground line.
(e) When bucket circuit is used, the pivot point must be specified as the bucket hinge pin, and the unit
blocked under the bucket hinge pin pivot point in order to minimize linkage movement.
(f) When the lift circuit is used, the pivot point must be specified as the lift arm hinge pin.
Wheel loaders shall have front axle blocked to eliminate change in position of pivot pins due to tire
deflection.
(g) If both circuits are used simultaneously, the dominating pivot point listed in (e) or (f) must be specified.
(h) If the circuit used causes the rear of the machine to leave the ground then the vertical force value
required to raise the rear of the machine is the breakout force.
(i) For irregular shaped buckets, the tip of the bucket cutting edge, referred to above shall mean the
farthest forward point of the cutting edge.
6. LIFTING CAPACITY
The maximum mass in kilograms (pounds) at the
center of gravity of SAE rated load in the bucket
that can be lifted at a specified height with the Fixed
bucket positioned to retain maximum load under
the following conditions:
(a) Machine with rear end tied down.
(b) Machine at operating weight and equipment Lifting Capacity
as specified. FVBH0012
3A-103
AH_25.book Page 104 Tuesday, March 23, 2004 9:41 AM
9. CARRY POSITION
The vertical distance from the ground in
millimeters (inches) to the centerline of the bucket
hinge pin, with the angle of approach at 15 B 15
degree.
3A-104
AH_25.book Page 105 Tuesday, March 23, 2004 9:41 AM
3A-105
AH_25.book Page 106 Tuesday, March 23, 2004 9:41 AM
WA320-3
WA250-5 WA250PT-5 WA320-5 WA380-5 WA380-3
CUSTOM
W/B.O.C 2.3 (3.0) 2.0 (2.6) 2.8 (3.7) 2.7 (3.55) 3.3 (4.3) 3.2 (4.2)
GENERAL PURPOSE
BUCKET W/teeth
2.1 (2.75) 2.6 (3.25) 2.5 (3.25) 3.1 (4.1) 3.0 (3.9)
(STOCKPILE)
W/segment
edge 3.2 (4.2)
W/B.O.C
1.9 (2.5) 2.3 (3.0) 2.9 (3.8) 2.8 (3.65)
GENERAL PURPOSE
W/teeth
BUCKET (EXCAVATING) 1.8 (2.35) 2.1 (2.75) 2.7 (3.5) 2.6 (3.4)
W/segment
edge 2.9 (3.8) 2.8 (3.65)
SPADE NOSE ROCK W/tip type
BUCKET teeth
W/B.O.C
LIGHT MATERIAL 2.7 (3.35) 3.2 (4.2) 4.0 (5.2) 4.0 (5.25)
BUCKET
BARE
2.5 (3.25) 3.0 (3.9) 3.8 (4.95)
LIGHT MATERIAL For multi-
BUCKET coupler 2.5 (3.25) 3.1 (4.0)
3A-106
AH_25.book Page 107 Tuesday, March 23, 2004 9:41 AM
3A-107
AH_25.book Page 108 Tuesday, March 23, 2004 9:41 AM
3A-108
AH_25.book Page 109 Tuesday, March 23, 2004 9:41 AM
WA900-3 WA1200-3
GENERAL PURPOSE W/B.O.C
BUCKET
(STOCKPILE) W/teeth
3A-109
AH_25.book Page 110 Tuesday, March 23, 2004 9:41 AM
5. Heavy-duty Bucket:
This bucket is used for digging and loading blasted rock on rubble mounds and rock
crushing job sites. It has 1-class-larger teeth, and a large, thicker wear plate, large
corner edge/side guard, and strengthened spill guard.
NOTE: When installing this bucket on machines other than the WA700 or WA800, to
maintain the stability of the machine, please install an additional
counterweight and an orifice (or retainer) for reducing the dumping shock of
the bucket .
6. Chip Bucket:
This is a large bucket used for loading loose materials with low specific gravity [below
0.55 t/m3 (930 lb/cu.yd)], such as chips and grain. The back and top are made of a
wire mesh to reduce the weight. This bucket can demonstrate its power in bucket
operations in the paper-manufacturing business and sawmills.
7. Skeleton Bucket:
This bucket is used for digging and loading blasted rock on rubble mounds and rock
crushing job sites. It has a lattice structure allows it to sift out soil and small rocks,
thereby enabling it to select only the rock materials.
9. Multi-purpose Bucket:
This is a versatile bucket that performs scraping, dozing, scooping and various other
tasks in addition to excavating and loading jobs. It is especially suited to leveling work
and material transport.
3A-110
AH_25.book Page 111 Tuesday, March 23, 2004 9:41 AM
FVBH0217
2. Bolt-on Teeth:
These teeth are suitable for loading or excavation of piles of earth or sand, blasted
rock, and jobs in the field that involve digging into the side of slopes. The special
heat treated, tensile strength steel alloy used in their production assures that they
will wear and have a long service life.
FVBH0218
3. Tip-type Teeth:
These teeth tips which are attached to an adapter that is welded or bolted to the
bucket edge. This means that an interchangeable part, the tooth tip, absorbs most
of the wear and protects the actual bucket edge. They give excellent performance
when used to handle blasted rock, piles of earth and similarly heavy duty tasks.
FVBH0219
FVBH0220
3A-111
AH_25.book Page 112 Tuesday, March 23, 2004 9:41 AM
Coal bucket
Scooping of light material Light material bucket
Is size of material Yes
to A
40mm or smaller?
No
Consult Komatsu.
Excavating bucket
(straight ege)
No
Consult Komatsu.
Bucket capacity
m3
Bucket capacity is On the chart, draw a ver-
A tical line corresponding to
determined by using
a selection chart. the material density.
Optimum capacity
of bucket is one On the chart, draw a ver-
Is material Yes
B corresponding to tical line corresponding to
density 1.6
material density 1.6 the material density.
or more?
on a selection chart
or smaller bucket. No 3
Consult Komatsu. 1.6 1.8 kg/m3 x 1000
Material density
Optimum capacity
of bucket is one
corresponding to Is material On the chart, draw a ver-
Yes
C material density 1.8 density 1.8 tical line corresponding to
on a selection chart or more? the material density.
or smaller bucket.
No
Consult Komatsu. Select this capacity
bucket or smaller one.
3A-112
AH_25.book Page 113 Tuesday, March 23, 2004 9:41 AM
The appropriate bucket capacity for each model is determined in relation with the density of material that the
bucket carries.
The graphs are shown for the models WA120-3. The capacity of the currently available buckets for each
model are shown there. Komatsu can develop other sizes of buckets according to these graphs, if it is
requested through a distributor.
Bucket capacity in the graphs means SAE heaped capacity (Calculation method indicated on page 4A-88).
The line in the graph shows the case when the bucket fill factor is 100%.
WA150-5
1.7 m3 Light Material Bucket
(2.2 cu.yd) (Scooping and loading of light material)
Bucket capacity: m3 (cu.yd)
WA200-5
2.4 m3 Light Material Bucket
(3.1 cu.yd) (Scooping and loading of light material)
Bucket capacity: m3 (cu.yd)
WA200PT-5
1.8 m3 Stockpile Bucket
(2.4 cu.yd) (Loading and excavating of soil, sand and a
100
90
105
Bucket capacity: m3 (cu.yd)
Bu
2.6
Bu
material)
Bu
ck
c
(3.4)
k
et
cke
et
Fi
Fil
tF
ll
l
ill
2.2
(2.8)
1.8 1.8m3 2.4yd3
Stockpile Backet
(2.4)
1.4
(1.8)
1.0
(1.3)
3A-113
AH_25.book Page 114 Tuesday, March 23, 2004 9:41 AM
WA250-5
2.7 m3 Light Material Bucket
(3.5 cu.yd) (Scooping and loading of light material)
Bucket capacity: m3 (cu.yd)
WA250PT-5
2.0 m3 Stockpile Bucket
(2.6 cu.yd) (Loading and excavating of soil, sand and a
10
90
1 05
Bu
material)
Bu
2.8
Bu
ck
c
e
k
cke
tF
et
(3.7)
ill
F
tF
il l
ill
2.4
(3.1)
2.0 2.0m3 2.6yd3
Stockpile Backet
(2.6)
1.6
(2.1)
1.2
(1.6)
WA320-5
3.2 m3 Light Material Bucket
(4.2 cu.yd) (Scooping and loading of light material)
Bucket capacity: m3 (cu.yd)
WA320-3 CUSTOM
cu.yd m3 Capacity
Heaped Struck
m3
(cu.yd)
Bucket capacity
4.2 3.2
3A-114
AH_25.book Page 115 Tuesday, March 23, 2004 9:41 AM
WA380-5
4.0 m3 Light Material Bucket with BOC (Scooping
Bucket fill factor (5.2 cu.yd) and loading of light material)
Bucket capacity: m3 (cu.yd)
4.0
(5.2) 3.3 m3 General Purpose Bucket with BOC
115 100 95% (4.3 cu.yd) (Loading and excavating of soil, sand and
3.3 variety of other commonly handled
(4.3) material)
2.9 2.9 m3 Excavating Bucket with BOC
(3.8) (3.8 cu.yd) Excavating Bucket with Teeth and
Segment Edge (Loading and excavating of
2.7
(3.5) crushed or blasted rock)
1000 1200 1400 1600 1800 2000 2200 kg/m3 2.7 m3 Excavating Bucket with Teeth
(3.5 cu.yd) (Loading and excavating of blasted rock)
2000 2500 3000 3500 lb/cu.yd
FVBH0185A
WA380-3
Capacity
Heaped Struck
m3
(cu.yd)
I General-purpose bucket with bolt-on
cutting edge; (Loading and 3.2 2.7
excavating of soil, sand and variety of (4.2) (3.55)
other commonly handled materials)
3.0 2.6
II General-purpose bucket with teeth
(3.9) (3.9)
III Excavating bucket with bolt-on cutting 2.8 2.35
edges (3.65) (3.07)
IV Excavating bucket with teeth;
(Loading and excavating of crushed 2.6 2.2
(3.4) (2.9)
rock and blasted rock)
V Light material bucket with bolt-on 4.0 3.4
cutting edges; (A lighter-weight, large-
(5.25) (4.45)
capacity bucket)
WA420-3
cu.yd m3 Capacity
5.0 Heaped Struck
m3
4.2 4.6
(cu.yd)
I General-purpose bucket with bolt-on
Bucket capacity
3A-115
AH_25.book Page 116 Tuesday, March 23, 2004 9:41 AM
WA430-5
4.6 m3 Light Material Bucket with BOC
Bucket fill factor (6.0 cu.yd) (Scooping and loading of light material)
4.6
(6.0) 3.7 m3 General Purpose Bucket with BOC
Bucket capacity: m3 (cu.yd)
115 100 95% (4.8 cu.yd) (Loading of crushed stone and dry sand)
3.7
(4.8) 3.5 m3 General Purpose Bucket with Teeth
(4.6 cu.yd) (Loading and excavating of soil, sand and
3.5 variety of other commonly handled
(4.6) material)
3.3 3.3 m3 Excavating Bucket with BOC
(4.3) (4.3 cu.yd) Excavating Bucket with Bolt-on Teeth and
Segments
3.1 (Loading or excavating of blasted rock)
(4.1)
1000 1200 1400 1600 1800 2000 2200 kg/m3 3.1 m3 Excavating Bucket with Teeth
3
(4.1 cu.yd) Rock Bucket with Teeth (Spade Nose)
2000 2500 3000 3500 lb/yd (Loading or excavating of blasted rock)
Material density FVBH0329
WA470-5
5.2 m3 Light Material Bucket with BOC
Bucket fill factor
(6.8 cu.yd) (Scooping and loading of light material)
5.2
(6.8) 4.6 m3 Loose Material Bucket with BOC
Bucket capacity: m3 (cu.yd)
WA470-3
Capacity
Heaped Struck
m3
(cu.yd)
I General-purpose bucket with bolt-on
cutting edge; (Loading and excavating of 4.2 3.6
soil, sand and variety of other commonly (5.5) (4.7)
handled materials)
3.9 3.4
II General-purpose bucket with teeth
(5.1) (4.45)
III Excavating bucket with bolt-on cutting 3.8 3.3
edges (5.0) (4.3)
IV Excavating bucket with teeth; (Loading
3.6 3.1
and excavating of crushed rock and
(4.7) (4.05)
blasted rock)
V Light material bucket with bolt-on cutting
5.2 4.5
edges; (A lighter-weight, large-capacity
(6.8) (5.9)
bucket)
VI Rock bucket with teeth; (Spade nose). 3.5 3.0
(Loading and excavating of blasted rock) (4.6) (3.9)
3A-116
AH_25.book Page 117 Tuesday, March 23, 2004 9:41 AM
WA480-5
6.1 m3 Light Material Bucket with BOC
Bucket fill factor
(8.0 cu.yd) Loose Material Bucket with BOC
6.1 (Loading of crushed stone and dry sand)
(8.0)
Bucket capacity: m3 (cu.yd)
WA500-3
cu.yd m3 Capacity
9
7 Heaped Struck
m3
(cu.yd)
Bucket capacity
6
I Excavating bucket (straight edge) 4.3 3.6
7 with teeth (5.6) (4.7)
6.5 5 II Excavating bucket (spade nose) with 5 4.1
4.5 teeth and segment edge (5.9) (5.4)
5.6 4.3
III General-purpose bucket with bolt on 5.0 4.6
cutting edge without teeth ; Loading (6.5) (6.0)
4 3 stockpile products
1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
WA500-3 (High-lift)
cu.yd m3 Capacity
9 7 Heaped Struck
m3
8 (cu.yd)
Bucket capcity
6
I Excavating bucket (straight edge) 4.2 3.6
7 with teeth (5.6) (4.8)
5
6
4
5
4 3
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
WA600-3
cu.yd m3 Capacity
10
Heaped Struck
9 m3
(cu.yd)
Bucket capacity
10
8 I Excavating bucket (straight edge) 6.1 5.1
with tip teeth (8.0) (6.7)
II Excavating bucket (spade nose) with 6.1 5.1
8 6 tip teeth (8.0) (6.7)
11.0 9.5
III Coal bucket (straight edge)
4 (14.4) (12.4)
4
1.0 1.2 1.4 1.5 1.8 2.0 2.2 2.4
kg/m3 x 1000
3A-117
AH_25.book Page 118 Tuesday, March 23, 2004 9:41 AM
WA600-3 (High-lift)
cu.yd m3 Capacity
10 Heaped Struck
m3
12 (cu.yd)
Bucket capcity
6
4
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
WA700-3
cu.yd m3 Capacity
10 Heaped Struck
m3
(cu.yd)
Bucket capacity
12
10 I Excavating bucket (straight edge) 8.7 7.6
without tip teeth (11.4) (9.9)
II Excavating bucket (spade nose) 8.7 7.6
10 8 without tip teeth (11.4) (9.9)
III General-purpose bucket (straight 9.4 8.2
8 edge) without tip teeth (12.3) (10.7)
6
1.0 1.2 1.4 1.5 1.8 2.0 2.2 2.4
kg/m3 x 1000
WA700-3 (High-lift)
cu.yd m3 Capacity
12 Heaped Struck
m3
14
(cu.yd)
Bucket capcity
8 6
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
WA800-3
Capacity
Heaped Struck
m3
(cu.yd)
I Excavating bucket (spade nose) with 11.0 9.3
tip teeth (14.4) (12.2)
12.3 10.4
II Stockpile (spade nose) with teeth
(16.1) (13.6)
3A-118
AH_25.book Page 119 Tuesday, March 23, 2004 9:41 AM
WA800-3 (High-lift)
cu.yd m3 Capacity
18 14
Heaped Struck
m3
(cu.yd)
Bucket capcity
8
1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8
kg/m3 x 1000
WA900-3
Capacity
Heaped Struck
m3
(cu.yd)
I Excavating bucket (spade nose) with 13.0 11.0
tip teeth (17.0) (14.4)
WA900-3 (High-lift)
cu.yd m3 Capacity
18 14
Heaped Struck
m3
(cu.yd)
Bucket capcity
8
1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8
kg/m3 x 1000
WA1200-3
Capacity
115 100 95% Heaped Struck
m3
35.0
(45.5)
(cu.yd)
I Excavating bucket (spade nose) with 20.0 17.2
30.0
(39.0) tip teeth (26.2) (22.5)
Bucket capacity: m3 (cu.yd)
20.0
(26.0)
18.0
(23.4)
16.5
(21.5)
14.0
(18.2)
500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000 kg/m3
1000 1500 2000 2500 3000 3500 4000 4500 5000 lb/cu.yd
FVBH0250
3A-119
AH_25.book Page 120 Tuesday, March 23, 2004 9:41 AM
WA1200-3 (High-lift)
Bucket fill factor Capacity
35.0
Heaped Struck
m3
(45.8) (cu.yd)
Bucket capacity: m3 (cu.yd)
3A-120
AH_25.book Page 121 Tuesday, March 23, 2004 9:41 AM
kg/m3
1.7 m3 Loose material bucket with bolt-on cutting
1.0
1.2 1.4 1.6 1.8 2.0 2.2 2.4 x 1000 (2.25 cu.yd) edge; (A lighter-weight, large capacity
bucket)
2 2.5 3 3.5 4 lb/cu.yd
x 1000
Material density
3A-121
AH_25.book Page 122 Tuesday, March 23, 2004 9:41 AM
2.7
(3.5)
1000 1200 1400 1600 1800 2000 2200 kg/m3
3A-122
AH_25.book Page 123 Tuesday, March 23, 2004 9:41 AM
6
5.5 I Excavating bucket (straight edge) with 5.5 4.5
7
6.5 5.0
teeth (7.2) (5.9)
II Excavating bucket (straight edge) with 4.5 3.9
5.9 4.5 teeth & segment edge (5.9) (5.1)
5.6
III General-purpose bucket (straight 5.0 4.6
edge) with bolt on cutting edge (6.5) (6.0)
4 3
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
1.5 2.0 2.5 3.0 3.5 4.0
lb/cu.yd x 1000
Material density
6
(cu.yd)
I Excavating bucket (straight edge) with 6.2 5.1
7 teeth (8.0) (6.6)
6.5
II Excavating bucket (spade nose) with 6.2 5.1
teeth (8.0) (6.6)
5.9
5.6
4 3
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
8
6
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4
kg/m3 x 1000
3A-123
AH_25.book Page 124 Tuesday, March 23, 2004 9:41 AM
Bucket
Bucket type Capacity (m3)
0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1
Material density t/m3
Bucket
Bucket type Capacty (m3)
0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2.0 2.1
Material density t/m3
3A-124
AH_25.book Page 125 Tuesday, March 23, 2004 9:41 AM
3A-125
AH_25.book Page 126 Tuesday, March 23, 2004 9:41 AM
TOOTH SHAPES
Model 1 2 3 4 5 6 7 8 9 10
WA250, WA320 – –
WA420, WA450 – –
WA500, WA600 –
: Available
3A-126
AH_25.book Page 127 Tuesday, March 23, 2004 9:41 AM
TOOTH SHAPES
Model 1 2 3 4 5 6 7 8 9 10
WA120 – – – – – –
WA180, WA250 – – –
WA420, WA450 –
WA500 –
WA700
WA800, WA900 – – –
: Available
TOOTH SHAPES
Model 1 2 3
WA1200
: Available
3A-127
AH_25.book Page 128 Tuesday, March 23, 2004 9:41 AM
3A-128
AH_25.book Page 129 Tuesday, March 23, 2004 9:41 AM
• Log-lumber grapple
The log-lumber grapple is an all-round tool for log and lumber handling capable of
dealing with lumber, long logs of large diameter or short logs of small diameter as
well as lumber. However, forks of log-lumber grapple are fixed for strength so it is
not suitable for use in forklift operations.
• Log-lumber fork
Log-lumber fork has the same features as log-lumber grapple.
This attachment has no top clamps.
• Lumber grapple
The "L" type forks of the lumber fork permit handling of lumber and logs of
smaller diameter and shorter length. Clearance between left and right forks
is adjustable according to the materials being handled.
• Lumber fork
Lumber fork has the same features as lumber grapple.
This attachment has no top clamps.
• Dumping fork
Useful for truck-loading pulpwood from stacks, and for gathering and loading
pulpwood into stacks or onto trucks. Also usable in handling logs of smaller
diameter and shorter length. A lighter, handy version of log handling
attachments. It has no top clamp. It can load logs when tilted back to prevent
them rolling over the fork.
• Pipe grapple
This is a log grapple with cushioning material to allow it to handle pipes and similar
materials.
* : Cushioning material
3A-129
AH_25.book Page 130 Tuesday, March 23, 2004 9:41 AM
• Extension fork
If an extension fork is installed to the lumber fork, the efficiency of handling light
materials such as small diameter short logs can be improved.
• Multi-coupler
This is an attachment replacement device that makes it possible to speed up the
replacement of attachments and reduce the burden on the operator.
It is possible to remove and install attachments to match the purpose of the work
simply when sitting in the operator's seat, thereby greatly reducing time and labor.
3A-130
AH_25.book Page 131 Tuesday, March 23, 2004 9:41 AM
A. Scooping
1. Forward the machine to insert forks under piled logs while
watching fork tips.
2. Once logs are scooped by forks and tilted back fully, then close
the arms.
3. Lift fork 30-50 cm above the ground to carry.
NOTE: Use both forks evenly to scoop and grapple the center of
logs.
B. Loading work
1. Raise booms and forward the machine gradually to the
destination while keeping the fork in a full backward tilt.
2. Open clamper arms and unload logs while slowly lowering forks.
After unloading logs, shift the fork control lever to the "tilt" position
and the fork will return automatically to its preset position.
After closing the arms and reversing the machine, lower the
booms.
NOTE: When dumping a full load of logs, lower engine revolutions
to achieve gradual dumping.
Avoid sudden braking or steering with a full load of logs.
When loading onto trucks, be careful forks and logs do not
hit the sticks mounted on the truck's body sides.
D. Other operations
Wrong Good
1. To push logs, open the clamp arms and push them with the inside
of the fork, forming right angles with the logs.
NOTE: The dumping angle should be within 20°.
Avoid pushing logs with the front of the closed clamp arms.
2. To retract logs, lower fork and raise fork tips 50-100 cm above the
ground, then reverse the machine and retract the logs.
NOTE: Do not uproot tree roots with forks.
Dangerous operations, such as throwing grabbed logs for
placement in the depth of loading site, should be conducted
in open areas and only after the work site has been properly
cleared. Do not conduct these operations where damage to
the machine or other equipment is possible.
50~100cm
3A-131
AH_25.book Page 132 Tuesday, March 23, 2004 9:41 AM
3A-132
AH_25.book Page 133 Tuesday, March 23, 2004 9:41 AM
Model WA320-3
Item WA250-5** WA320-5** CUSTOM*3 WA380-3**
OPERATING WEIGHT kg (lb) 11030 (24,320) 13870 (30,580) 13580 (29,940) 16750 (36,930)
A. OVERALL LENGTH mm (ft.in) 7845 (25'9") 8360 (27'5") 8485 (27'10") 8945 (29'4")
B. OVERALL WIDTH mm (ft.in) 2470 (8'1") 2585 (8'6") 2585 (8'6") 2695 (8'8")
C. Max. tine height with tine mm (ft.in) 3580 (11'9") 3695 (12'2") 3675 (12'1") 3820 (12'6")
level
D. Reach, max. tine height mm (ft.in) 2240 (7'4") 2405 (7'11") 2430 (8'0") 2505 (8'3")
with tine level
E. Dumping clearance* mm (ft.in) 2665 (8'9") 2670 (8'9") 2650 (8'8") 2790 (9'2")
F. Dumping reach* mm (ft.in) 1880 (6'2") 2025 (6'8") 2045 (6'9") 2120 (7')
G. Overall tine width mm (ft.in) 1850 (6'1") 2100 (6'11") 2100 (6'11") 2100 (6'11")
H. Tine length mm (ft.in) 1675 (5'6") 1890 (6'2") 1890 (6'2") 1890 (6'2")
I. Max. tilt-back angle degree 29 31 30 31
TIRE SIZE 20.5-25-12PR 20.5-25-16PR 20.5-25-12PR 20.5-25-16PR
(L2) (L3)
Add. counterweight kg (lb) 300 (660) 520 (1,150) 750 (1,650) 750 (1,650)
* At 30° discharge angle
** With ROPS cab
*3 With cab
3A-133
AH_25.book Page 134 Tuesday, March 23, 2004 9:41 AM
Model
Item WA200-5** WA250-5** WA320-5**
OPERATING WEIGHT kg (lb) 9830 (21,680) 11090 (24,450) 13910 (30,670)
A. OVERALL LENGTH mm (ft.in) 7615 (25'0") 7625 (25'0") 8040 (26'5")
B. OVERALL WIDTH mm (ft.in) 2375 (7'10") 2470 (8'1") 2585 (8'6")
C. Max. tine height with tine mm (ft.in) 3485 (11'5") 3645 (12'0") 3765 (12'4")
level
D. Reach, max. tine height mm (ft.in) 2095 (6'11") 2085 (6'10") 2155 (7'1")
with tine level
E. Dumping clearance* mm (ft.in) 2635 (8'8") 2795 (9'2") 2860 (9'5")
F. Dumping reach* mm (ft.in) 1785 (5'10") 1780 (5'10") 1840 (6'0")
G. Overall tine width mm (ft.in) 2045 (6'9") 2045 (6'9") 2165 (7'1")
H. Tine length mm (ft.in) 1220 (4'0") 1220 (4'0") 1320 (4'4")
I. Max. tilt-back angle degree 27 26 27
TIRE SIZE 17.5-25-12PR (L2) 20.5-25-12PR (L2) 20.5-25-16PR (L3)
Add. counterweight kg (lb) 300 (660) 300 (660) 520 (1,150)
* At 30° discharge angle
** With high lift
Model
Item WA320-3 CUSTOM*3 WA380-3** WA380-5**
OPERATING WEIGHT kg (lb) 13620 (30,030) 16960 (37,390) 16700 (36,820)
A.OVERALL LENGTH mm (ft.in) 8165 (26'9") 8740 (28'8") 8915 (29'3")
B.OVERALL WIDTH mm (ft.in) 2585 (8'6") 2695 (8'10") 2695 (8'10")
C. Max. tine height with tine mm (ft.in) 3745 (12'3") 3870 (12'8") 3870 (12'8")
level
D. Reach, max. tine height mm (ft.in) 2180 (7'2") 2345 (7'8") 2345 (7'8")
with tine level
E. Dumping clearance* mm (ft.in) 2840 (9'4") 2915 (9'7") 2915 (9'7")
F. Dumping reach* mm (ft.in) 1865 (6'1") 2005 (6'7") 2005 (6'7")
G. Overall tine width mm (ft.in) 2165 (7'1") 2250 (7'5") 2250 (7'5")
H. Tine length mm (ft.in) 1320 (4'4") 1420 (4'10") 1420 (4'10")
I. Max. tilt-back angle degree 27 28 28
TIRE SIZE 20.5-25-12PR 20.5-25-16PR 20.5-25-20PR
Add. counterweight kg (lb) 750 (1,650) 750 (1,650) 708 (1,550)
* At 30° discharge angle
** With ROPS cab
*3 With cab
3A-134
AH_25.book Page 135 Tuesday, March 23, 2004 9:41 AM
Model WA320-3***
Item WA320-5** CUSTOM WA380-3** WA380-5**
OPERATING WEIGHT kg (lb) 13970 (30,800) 13680 (30,160) 16980 (37,430) 16790 (37,020)
A. OVERALL LENGTH mm (ft.in) 7720 (25'4") 7845 (25'9") 8455 (27'9") 8627 (28'4")
B. OVERALL WIDTH mm (ft.in) 2585 (8'6") 2585 (8'6") 2695 (8'10") 2695 (8'10")
C. Max. tine height with tine mm (ft.in) 3875 (12'9") 3855 (12'8") 3985 (13'1") 3985 (13'1")
level
D. Reach, max. tine height mm (ft.in) 1855 (6'1") 1880 (6'2") 2080 (6'10") 2080 (6'10")
with tine level
E. Dumping clearance* mm (ft.in) 3095 (10'2") 3075 (10'1") 3140 (10'4") 3140 (10'4")
F. Dumping reach* mm (ft.in) 1635 (5'4") 1660 (5'5") 1835 (6') 1835 (6')
G. Overall tine width mm (ft.in) 2200 (7'3") 2200 (7'3") 2300 (7'7") 2300 (7'7")
H. Tine length mm (ft.in) 1320 (4'4") 1320 (4'4") 1420 (4'8") 1420 (4'8")
I. Max. clamp opening height mm (ft.in) 2280 ( 7'6") 2280 (7'6") 2415 (7'11") 2415 (7'11")
J. Top clamp min. closure mm (ft.in) 850 (2'9") 850 (2'9") 900 (2'11") 900 (2'11")
diameter
20.5-25-16PR
TIRE SIZE (L3) 20.5-25-12PR 20.5-25-16PR 20.5-25-20PR
Add. counterweight kg (lb) 520 (1,150) 750 (1,650) 750 (1,650) 705 (1,550)
* At 30° discharge angle
** With ROPS cab
*** With steel cab
Model
WA420-3** WA450-3LL WA470-5** WA470-3***
Item
OPERATING WEIGHT kg (lb) 19900 (43,870) 23440 (51,680) 22550 (49,710) 22790 (50,240)
A. OVERALL LENGTH mm (ft.in) 8875 (29'1") 9265 (30'5") 9425 (31'0") 9315 (30'7")
B. OVERALL WIDTH mm (ft.in) 2820 (9'3") 3000 (9'10") 2920 (9'7") 2920 (9'7")
C. Max. tine height with tine mm (ft.in) 4150 (13'7") 4300 (14'1") 4230 (13'11") 4230 (13'11")
level
D. Reach, max. tine height mm (ft.in) 2070 ( 6'9") 2190 (7'1") 2315 (7'7") 2265 (7'5")
with tine level
E. Dumping clearance* mm (ft.in) 3275 (10'9") 3380 (11'1") 3315 (10'11") 3315 (10'11")
F. Dumping reach* mm (ft.in) 1785 (5'10") 1915 (6'3") 2045 (6'9") 1995 (6'7")
G. Overall tine width mm (ft.in) 2525 (8'3") 2685 (8'10") 2645 (8'8") 2645 (8'8")
H. Tine length mm (ft.in) 1420 (4'8") 1525 (5') 1525 (5') 1525 (5')
I. Max. clamp opening height mm (ft.in) 2525 (8'3") 2830 (9'3") 2765 (9'1") 2765 (9'1")
J. Top clamp min. closure mm (ft.in) 900 (2'11") 1000 (3'3") 1000 (3'3") 1000 (3'3")
diameter
TIRE SIZE 23.5-25-16PR 26.5-25-24PR 23.5-25-24PR 23.5-25-20PR
Add. counterweight kg (lb) 1045 (2,300) 1045 (2,300) 1030 (2,270) 1045 (2,300)
* At 30° discharge angle
** With ROPS cab
*** Rear tires are filled with calcium chloride, with steel cab & ROPS canopy
3A-135
AH_25.book Page 136 Tuesday, March 23, 2004 9:41 AM
Model
Item WA500-3***
OPERATING WEIGHT kg (lb) 33090 (72,950)
A. OVERALL LENGTH mm (ft.in) 10105 (33'2")
B. OVERALL WIDTH mm (ft.in) 3190 (10'6")
C. Max. tine height with tine mm (ft.in) 4375 (14'4")
level
D. Reach, max. tine height mm (ft.in) 2590 (8'6")
with tine level
E. Dumping clearance* mm (ft.in) 3300 (10'10")
F. Dumping reach* mm (ft.in) 2250 (7'5")
G. Overall tine width mm (ft.in) 2745 (9')
H. Tine length mm (ft.in) 1830 (6')
I. Max. clamp opening height mm (ft.in) 3035 (9'11")
J. Top clamp min. closure mm (ft.in) 1150 (3'9")
diameter
TIRE SIZE 29.5-25-22PR
Add. counterweight kg (lb) 2250 (4,960)
* At 30° discharge angle
** With ROPS cab
*** Rear tires are filled with calcium chloride, with steel cab & ROPS canopy
3A-136
AH_25.book Page 137 Tuesday, March 23, 2004 9:41 AM
4000
150
140
130 LIFTING CAPACITY
(TINES LEVEL)
120 3000
LIFTING CAPACITY
110 (TINES ROLLED BACK)
HINGE PIN HEIGHT
100
90
80 2000
70
60
STATIC TIPPING
LOAD
50 [MACHINE FULL TURN]
(TINES LEVEL)
40 1000
30
STATIC TIPPING
20 LOAD
[MACHINE STRAIGHT]
10 (TINES LEVEL)
0 0
2000 4000 6000 8000 10000 12000 Kg
0 10000 20000 lb
STATIC TIPPING LOAD(STRAIGHT)AND
LIFTING CAPACITY FVBH0342
WA320-5
Curves based on machine equipped with 20.5-25-16PR (L3) TL and counterweight
mm
in
5000
190 STATIC TIPPING
180 LOAD
[MACHINE FULL TURN]
170 (TINES LEVEL)
160 4000
150
140 LIFTING CAPACITY
130 (TINES LEVEL)
HINGE PIN HEIGHT
120 3000
110
100
90 LIFTING CAPACITY
(TINES ROLLED BACK)
80 2000
70
60
50
40 1000
30 STATIC TIPPING
20 LOAD
[MACHINE STRAIGHT]
10 (TINES LEVEL)
0 0
2000 4000 6000 8000 10000 12000 14000 Kg
10000 20000 30000 lb
STATIC TIPPING LOAD(STRAIGHT)AND
LIFTING CAPACITY FVBH0343
3A-137
AH_25.book Page 138 Tuesday, March 23, 2004 9:41 AM
mm
in
in
4000 4000
150 150
LIFTING CAPACITY
140 (TINES ROLLED BACK) 140
130 130 LIFTING CAPACITY
(TINES LEVEL)
120 3000 120 3000
LIFTING CAPACITY LIFTING CAPACITY
110 (TINES LEVEL) 110 (TINES ROLLED BACK)
HINGE PIN HEIGHT
100 100
90 90
80 2000 80 2000
70 70
STATIC TIPPING
60 LOAD 60
[MACHINE FULL TURN] STATIC TIPPING
(TINES LEVEL) LOAD
50 50 [MACHINE FULL TURN]
(TINES LEVEL)
40 1000 40 1000
30 30
STATIC TIPPING STATIC TIPPING
20 LOAD
20 LOAD
[MACHINE STRAIGHT] [MACHINE STRAIGHT]
10 (TINES LEVEL) 10 (TINES LEVEL)
0 0 0 0
2000 4000 6000 8000 Kg 2000 4000 6000 8000 10000 12000 Kg
0 4000 8000 12000 14000 lb 0 10000 20000 lb
STATIC TIPPING LOAD(STRAIGHT)AND STATIC TIPPING LOAD(STRAIGHT)AND
LIFTING CAPACITY FVBH0344 LIFTING CAPACITY FVBH0345
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
5000
190 STATIC TIPPING
180 LOAD
[MACHINE FULL TURN]
170 (TINES LEVEL)
160 4000
150
140 LIFTING CAPACITY
130 (TINES LEVEL)
HINGE PIN HEIGHT
120 3000
110
100
90 LIFTING CAPACITY
(TINES ROLLED BACK)
80 2000
70
60
50
40 1000
30 STATIC TIPPING
20 LOAD
[MACHINE STRAIGHT]
10 (TINES LEVEL)
0 0
2000 4000 6000 8000 10000 12000 14000 Kg
10000 20000 30000 lb
STATIC TIPPING LOAD(STRAIGHT)AND
LIFTING CAPACITY FVBH0346
3A-138
AH_25.book Page 139 Tuesday, March 23, 2004 9:41 AM
5000
190
180
170
160 4000
150
140
130
HINGE PIN HEIGHT
30
20
10
0 0
4000 6000 8000 10000 12000 14000 16000 Kg
10000 20000 30000 lb
STATIC TIPPING LOAD (STRAIGHT) AND
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
3A-139
AH_25.book Page 140 Tuesday, March 23, 2004 9:41 AM
4000
150
140
130 LIFTING CAPACITY
(TINES LEVEL)
120 3000
LIFTING CAPACITY
110 (TINES ROLLED BACK)
HINGE PIN HEIGHT
100
90
80 2000
70
60
STATIC TIPPING
LOAD
50 [MACHINE FULL TURN]
(TINES LEVEL)
40 1000
30
STATIC TIPPING
20 LOAD
[MACHINE STRAIGHT]
10 (TINES LEVEL)
0 0
2000 4000 6000 8000 10000 12000 Kg
0 10000 20000 lb
FVBH0347
5000
190 STATIC TIPPING
180 LOAD
[MACHINE FULL TURN]
170 (TINES LEVEL)
160 4000
150
140 LIFTING CAPACITY
130 (TINES LEVEL)
HINGE PIN HEIGHT
120 3000
110
100
90 LIFTING CAPACITY
(TINES ROLLED BACK)
80 2000
70
60
50
40 1000
30 STATIC TIPPING
20 LOAD
[MACHINE STRAIGHT]
10 (TINES LEVEL)
0 0
2000 4000 6000 8000 10000 12000 14000 Kg
10000 20000 30000 lb
FVBH0348
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
3A-140
AH_25.book Page 141 Tuesday, March 23, 2004 9:41 AM
5000
190
180
170
160 4000
150
140
LIFTING CAPACITY
130 (TINES LEVEL)
HINGE PIN HEIGHT
STATIC TIPPING
120 3000 LOAD
[MACHINE
110 FULL TURN]
(TINES LEVEL)
100
90
LIFTING CAPACITY
80 2000 (TINES ROLLED
BACK)
70
STATIC TIPPING
60 LOAD
[MACHINE
50 STRAIGHT]
40 1000 (TINES LEVEL)
30
20
10
0 0
4000 6000 8000 10000 12000 14000 16000 Kg
10000 20000 30000 lb
STATIC TIPPING LOAD (STRAIGHT) AND
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
3A-141
AH_25.book Page 142 Tuesday, March 23, 2004 9:41 AM
5000
190 STATIC TIPPING
180 LOAD
[MACHINE FULL TURN]
170 (TINES LEVEL)
160 4000
150
140 LIFTING CAPACITY
130 (TINES LEVEL)
HINGE PIN HEIGHT
120 3000
110
100
90 LIFTING CAPACITY
(TINES ROLLED BACK)
80 2000
70
60
50
40 1000
30 STATIC TIPPING
20 LOAD
[MACHINE STRAIGHT]
10 (TINES LEVEL)
0 0
2000 4000 6000 8000 10000 12000 14000 Kg
10000 20000 30000 lb
FVBH0349
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
WA380-3 WA380-5
Curves based on machine equipped with Curves based on machine equipped with 20.5-25-
20.5-25-16PR (L3) TL and counterweight for logger 20PR (L3) TL and counterweight for logger
mm
in
5000
190
180
170
160 4000 LIFTING CAPACITY
(TINES LEVEL)
150
140
130
HINGE PIN HEIGHT
STATIC TIPPING
120 3000 LOAD
[MACHINE
110 FULL TURN]
(TINES LEVEL)
100
90 LIFTING CAPACITY
80 2000 (TINES ROLLED
BACK)
70
STATIC TIPPING
60 LOAD
[MACHINE
50 STRAIGHT]
40 1000 (TINES LEVEL)
30
20
10
0 0
4000 6000 8000 10000 12000 14000 16000 Kg
10000 20000 30000 lb
STATIC TIPPING LOAD (STRAIGHT) AND
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
3A-142
AH_25.book Page 143 Tuesday, March 23, 2004 9:41 AM
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
WA470-3 WA500-3
Curves based on machine equipped with 23.5-25- Curves based on machine equipped with
20PR (L3) TL and counterweight for logger 29.5-25-22PR (L3) TL and counterweight for logger
STATIC TIPPING LOAD (STRAIGHT) AND STATIC TIPPING LOAD (STRAIGHT) AND
LIFTING CAPACITY LIFTING CAPACITY
3A-143
AH_25.book Page 144 Tuesday, March 23, 2004 9:41 AM
3A-144
AH_25.book Page 145 Tuesday, March 23, 2004 9:41 AM
• : Standard tire
T/L : Tubeless tire
W/T : Tubed tire
SB : Steel breaker tire
SSB : Side steel breaker tire
3A-145
AH_25.book Page 146 Tuesday, March 23, 2004 9:41 AM
3A-146
AH_25.book Page 147 Tuesday, March 23, 2004 9:41 AM
• : Standard tire
T/L : Tubeless tire
W/T : Tubed tire
SB : Steel breaker tire
SSB : Side steel breaker tire
*** : Germany source
3A-147
AH_25.book Page 148 Tuesday, March 23, 2004 9:41 AM
WA420 - WA480
ft mm
5000
15 4500
Dumping clearance / Loading height
4000
WA470 HL
3500
WA480
HD405
10 3000 WA420 WA470 HD325
HD255
2500
2000
5 1500
1000
500
0 0
0 1000 2000 3000 4000 5000 mm
0 5 10 15 ft
Dumping reach / Body width
Chart shows dumping reach and dumping clearance of standard size buckets.
HL means high lift boom.
◆ : Indicates dumping reach and clearance at the end of teeth or BOC.
● : Indicates the top corner of body.
WA500 - WA700
ft mm
5000
WA700 HL
15 4500
WA600 HL WA700
Dumping clearance / Loading height
4000
HD605
WA500 HL
HD465
3500
WA600
HD405
10 3000 HD325
WA500 HD255
2500
2000
5 1500
1000
500
0 0
0 1000 2000 3000 4000 5000 mm
0 5 10 15 ft
Dumping reach / Body width
Chart shows dumping reach and dumping clearance of standard size buckets.
HL means high lift boom.
◆ : Indicates dumping reach and clearance at the end of teeth or BOC.
● : Indicates the top corner of body.
3A-148
AH_25.book Page 149 Tuesday, March 23, 2004 9:41 AM
WA800 - WA1200
ft mm
10000
30 9000
8000
Dumping clearance / Loading height
WA1200 HL 930E
7000
830E
WA1200
20 6000 630E
730E
WA800 HL
WA900 HL HD1500
5000
WA800 WA900 HD985
4000 HD785
10 3000
2000
1000
0 0
0 2000 4000 6000 8000 10000 mm
0 10 20 30 ft
Dumping reach / Body width
Chart shows dumping reach and dumping clearance of standard size buckets.
HL means high lift boom.
◆ : Indicates dumping reach and clearance at the end of teeth or BOC.
● : Indicates the top corner of body.
3A-149
AH_25.book Page 150 Tuesday, March 23, 2004 9:41 AM
4.6 General-purpose
bucket with bolt-on 3205 (10'6") 3 4
(6.0)
WA480 cutting edges
4.3 General-purpose
3080 (10'1") 3
(5.6) bucket with teeth
General purpose
4.3 (excavating, straight 3025 (9'11") 3
(5.6)
WA500 edges) with teeth
4.3 Spade nose rock 2770 (9'1")
(5.6) bucket with tip teeth
General purpose
WA500 4.2
(excavating, straight 3565 (11'8") 3 5 5
High lift (5.5)
edges) with teeth
6.1 Spade nose rock
WA600 3350 (11'0") 2 3 4
(8.0) bucket with teeth
WA600 5.6 Spade nose rock 3995 (13'1") 2 4 4 5 6
High lift (7.3) bucket with teeth
8.7 Spade nose rock
WA700 (11.4) bucket with teeth 4040 (13'3") 2 2 3 4 4
WA700 8.0 Spade nose rock 4645 (15'3") 2 3 3 4 4 6 7
High lift (10.5) bucket with teeth
3A-150
AH_25.book Page 151 Tuesday, March 23, 2004 9:41 AM
DR
L W
1/6W
DC
H
G.L
FVBH0298
3A-151
AH_25.book Page 152 Tuesday, March 23, 2004 9:41 AM
3A-152
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 3B
REACH LOADERS
CONTENTS
Features .................................................................... 3B-2
Specifications ........................................................... 3B-3
Dimensions ............................................................... 3B-4
3B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Other
• The low-noise design is suitable for residential areas.
• Closed wet-type brakes assure positive braking even in muddy water.
• Less tire slippage due to wide tread and torque-proportioning differential gears.
• Excellent travel stability due to the long wheelbase.
• Stopping the engine is done with a key, the same as in an automobile.
• Quick movement between job sites at max. travel speed 30 km/h (18.8MPH).
3B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
WR8 WR11-3
Item
OPERATING WEIGHT kg (lb) 5700 (12,570) 8635 (19,040)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 55 (41.2)/2200 84 (62.5)/2400
BUCKET CAPACITY m3 (cu.yd) 0.8 (1.05) 1.3 (1.7)
PERFORMANCE:
Travel speeds: km/h(MPH)
Forward 1st 6.5 (4.0) 6.3 (3.9)
2nd 12.2 (7.6) 12.0 (7.5)
3rd 29.0 (18.0) 30.0 (18.6)
Reverse 1st 6.8 (4.2) 6.5 (4.0)
2nd 13.1 (8.1) 12.2 (7.6)
3rd 30.0 (18.6) 30.5 (19.0)
Turning radius mm(ft.in) 4705 (15'5") 5830 (19'2")
(Outside corner of bucket)
DIMENSIONS:
Overall length mm(ft.in) 5005 (16'5") 6240 (20'6")
Overall width mm(ft.in) 1910 (6'3") 2250 (7'5")
Overall height mm(ft.in) 2800 (9'2") 3035 (9'11")
Wheelbase mm(ft.in) 2450 (8') 2915 (9'7")
Treads (front and rear) mm(ft.in) 1470 (4'10") 1780 (5'10")
Articulation angle (each) degree 40 37
ENGINE:
Model KOMATSU KOMATSU
4D95L S4D102E
No. of cylinders- mm (in) 4-94 × 115 4-102 × 120
bore × stroke (3.7 × 4.5) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 3.26 (199) 3.92 (239)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 63 (16.6) 133 (35.1)
3B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
WR8
WR11-3
37
1780(5’10")
2390(7’10")
2250(7’5")
5830
37
(19’2
")
5030(16’6)
45
1460
(4’9")
4000(13’1")
3500(11’6")
3200(10’6")
3080(10’1")
45 850(2’9")
2695(8’10")
2945(9’8")
2930(9’7")
58
(2.6")
65
R
16
(1’4")
16
.9 .9
400
-2 4-10 -2 4-10
P
G.L
210(8.3")
(1.6")
40
2150(7’1") 2915(9’7")
10
6485(21’3")
1000(3’3") 1905(6’3") FVBH0021
3B-4
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 3C
WHEEL DOZERS
CONTENTS
Features .................................................................... 3C-2
Specifications ........................................................... 3C-3
Dimensions ............................................................... 3C-4
3C-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
• Komatsu components throughout the machine assure years of reliability and high-performance service.
• Adjustment-free wet disc brakes for steady braking and extended service life.
• Electronic Display and Monitoring System for minimized maintenance.
• A large drawbar horsepower with fuel-efficient, powerful Komatsu diesel engine for high productivity and
maneuverability.
• Fingertip control with Electrically Controlled Transmission.
• A tiltable steering wheel and fully adjustable suspension seat.
3C-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
WD420-3 WD500-3 WD600-3 WD900-3
Item
OPERATING WEIGHT kg (lb) 20000 (44,100) 26900 (59,300) 42900 (94,577) 100000 (220,460)
FLYWHEEL HORSEPOWER HP (kW)/rpm 224 (167)/2200 315 (235)/2100 485 (362)/2000 853 (637)/2000
BLADE CAPACITY m3 (cu.yd) 3.1 (4.1) 5.1 (6.7) 8.0 (10.5) 26.0 (34.0)
PERFORMANCE:
Travel speed km/h (MPH)
Forward 1st 6.3 (3.9) 7.1 (4.4) 6.5 (4.0) 7.0 (4.3)
2nd 11.7 (7.3) 12.6 (7.8) 11.8 (7.3) 12.3 (7.6)
3rd 20.5 (12.7) 21.2 (13.2) 20.8 (12.9) 28.0 (17.4)
4th 32.8 (20.4) 34.8 (21.6) 36.2 (22.5)
Reverse 1st 6.6 (4.1) 7.9 (4.9) 7.2 (4.5) 7.1 (4.4)
2nd 12.2 (7.6) 14.1 (8.8) 13.0 (8.1) 12.4 (7.7)
3rd 21.2 (13.2) 23.5 (14.6) 23.0 (14.3) 28.3 (17.6)
4th 33.9 (21.1) 38.1 (23.7) 40.0 (24.9)
Turning radius mm (ft.in) 6670 (21'11") 7475 (24'7") 9200 (30'2")
(Outside corner of blade)
Max. rim pull kg (lb) 18100 (39,900) 26500 (58,420) 42800 (94,360) 100000 (220,460)
DIMENSIONS:
Overall length mm (ft.in) 7160 (23'6") 7930 (26") 9285 (30'6") 12035 (39'6")
Overall width mm (ft.in) 2820 (9'3") 3190 (10'6") 3570 (11'9") 6470 (21'3")
Overall height mm (ft.in) 3370 (11'1") 3860 (12'8") 4245 (13'11") 5215 (17'1")
Wheelbase mm (ft.in) 3300 (10'11") 3600 (11'10") 4100 (13'5") 5450 (31')
Treads (front and rear) mm (ft.in) 2200 (7'3") 2400 (7'10") 2650 (8'8") 3350 (11')
Articulation angle degree 40 40 40 40
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SA6D108 S6D140E SAA6D170E-3 SA12V140
No. of cylinders- mm (in) 6-108 × 130 6-140 × 165 6-170 x 170 12-140 × 165
bore × stroke (4.3 × 5.1) (5.5 × 6.5) (6.69 x 6.69) (5.5 × 6.5)
Piston displacement ltr. (cu.in) 7.15 (436) 15.24 (930) 23.15 (1413) 30.5 (1861)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 340 (90) 465 (123) 670 (177) 1430 (378)
TIRE:
(front) 23.5-25-12PR 29.5-25-22PR 35/65-33-24PR 45/65-R45XLDD (L4)
(rear) 23.5-25-12PR 29.5-25-22PR 35/65-33-25PR 45/65-R45XLDD (L4)
3C-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
WD420-3
Blade type Straight Blade
Blade capacity (SAE Rated) m3 (cu.yd) 3.1 (4.1)
A Blade width mm (ft.in) 3745 (12'3")
B Max. lift above ground mm (ft.in) 1190 (3'11")
C Max. drop below ground mm (ft.in) 510 (1'8")
D Max. tilt adjustment mm (ft.in) 950 (3'1")
Max. pitch angle adjustment degree 21°
E Overall length mm (ft.in) 7160 (23'6")
F Front overhang mm (ft.in) 1760 (5'9")
Turning radius mm (ft.in) 6670 (21'11")
Operating weight (include ROPS) kg (lb) 20000 (44100)
WD500-3
Blade type Straight Blade
Blade capacity (SAE Rated) m3 (cu.yd) 5.1 (6.7)
A Blade width mm (ft.in) 4550 (14'11")
B Max. lift above ground mm (ft.in) 1255 (4'1")
C Max. drop below ground mm (ft.in) 440 (1'5")
D Max. tilt adjustment mm (ft.in) 1260 (4'2")
Max. pitch angle adjustment degree 9°
E Overall length mm (ft.in) 7930 (26)
F Front overhang mm (ft.in) 1860 (6'1")
Turning radius mm (ft.in) 7485 (24'7")
Operating weight (include ROPS) kg (lb) 26900 (59300)
WD600-3
Blade type Straight Blade
Blade capacity (SAE Rated) m3 (cu.yd) 8.0 (10.5)
A Blade width mm (ft.in) 5100 (16'9")
B Max. lift above ground mm (ft.in) 1500 (4'11")
C Max. drop below ground mm (ft.in) 450 (17.7")
D Max. tilt adjustment mm (ft.in) 1430 (4'8")
Max. pitch angle adjustment degree 23°
E Overall length mm (ft.in) 9285 (30'6")
F Front overhang mm (ft.in) 2205 (7'3")
Turning radius mm (ft.in)
Operating weight (include ROPS) kg (lb) 42900 (94,360)
3C-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
WD900-3
Blade type Semi-U blade Coal blade
Blade capacity (SAE Rated) m3 (cu.yd) 26.0 (34.0) 45.0 (58.9)
A Blade width mm (ft.in) 6470 (21'3") 7400 (24'3")
B Max. lift above ground mm (ft.in) 1580 (5'2") 1560 (5'1")
C Max. drop below ground mm (ft.in) 680 (2'3") 680 (3'3")
D Max. tilt adjustment mm (ft.in) 1330 (4'4") 1710 (5'7")
Max. pitch angle adjustment degree 8° 8°
E Overall length mm (ft.in) 12035 (39’6")
F Front overhang mm (ft.in) 3385 (11'1")
Turning radius mm (ft.in) 11285 (37')
Operating weight (include ROPS) kg (lb) 100000 (220460)
3C-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 3D
TRASH COMPACTORS
& TRASH LOADERS
CONTENTS
Features .................................................................... 3D-2
Specifications ........................................................... 3D-3
Dimensions ............................................................... 3D-4
3D-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
3D-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
WF450T-3 WF550T-3 WF650T-3
Item
OPERATING WEIGHT kg (lb) 24600 (54,230) 34500 (76,060) 45500 (100,310)
FLYWHEEL HORSEPOWER HP (kW)/rpm 259 (194)/2200 316 (235)/2100 439 (327)/2000
PERFORMANCE
Travel speeds: km/h (MPH)
Forward 1st 6.2 (3.9) 5.0 (3.1) 5.0 (3.1)
2nd 11.0 (6.8) 8.6 (5.3) 8.6 (5.3)
Reverse 1st 6.5 (4.0) 5.5 (3.4) 5.5 (3.4)
2nd 11.5 (7.1) 9.6 (6.0) 9.5 (5.9)
Turning radius mm (ft.in) 7000 (23') 7504 (24'7'') 8590 (28'2'')
(Outside corner of blade)
Max. rim pull kg (lb) 21500 (474,00) 38000 (83,780) 57000 (125,660)
DIMENSIONS:
Overall length mm (ft.in) 7520 (24'8'') 8145 (26'9'') 8925 (29'3'')
Overall width mm (ft.in) 3400 (11'2") 3800 (12'6'') 4300 (14'1'')
Overall height mm (ft.in) 3615 (11'10'') 4050 (13'3'') 4430 (14'6'')
Wheelbase mm (ft.in) 3400 (11'2'') 3600 (11'10'') 4100 (13'5'')
Treads (front and rear) mm (ft.in) 2350 (7'9'') 2600 (8'6'') 2900 (9'6'')
Articulation angle degree 40 40 40
ENGINE:
Model KOMATSU KOMATSU KOMATSU
S6D125E S6D140E SA6D170E
No. of cylinders- mm (in) 6-125 × 150 6-140 × 165 6-170 × 170
bore × stroke (4.92 × 5.91) (5.51 × 6.50) (6.69 × 6.69)
Piston displacement ltr. (cu.in) 11.04 (674) 15.24 (928) 23.15 (1,413)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 390 (103) 630 (166) 890 (235)
Model
WF350-3 WF450-3 WF550-3
Item
OPERATING WEIGHT kg (lb) 19510 (42,220) 24950 (55,010) 35000 (77,160)
FLYWHEEL HORSEPOWER HP (kW)/rpm 187 (138)/3200 259 (194)/2200 316 (235)/2100
BUCKET CAPACITY m3 (cu.yd) 3.0 (3.9) 3.7 (4.8) 4.7 (6.1)
PERFORMANCE
Travel speeds: km/h (MPH)
Forward 1st 7.1 (4.4) 6.2 (3.9) 5.1 (3.2)
2nd 11.4 (7.1) 11.2 (7.0) 9.2 (5.7)
Reverse 1st 7.4 (4.6) 6.4 (4.0) 7.9 (4.9)
2nd 11.8 (7.3) 11.7 (7.3) 14.1 (8.8)
Turning radius mm (ft/in) 6730 (22'1'') 6955 (22'10'') 7595 (24'11'')
(Outside corner of bucket)
Max. rim pull kg (lb) 16300 (35,940) 20800 (45,860) 38000 (83,780)
DIMENSIONS:
Overall length mm (ft.in) 8020 (26'4'') 8825 (28'11'') 9580 (31'5'')
Overall width mm (ft.in) 2845 (9'4'') 3290 (10'10'') 3900 (12'10'')
Overall height mm (ft.in) 3375 (11'1") 3455 (11'4'') 3905 (12'10'')
Wheelbase mm (ft.in) 3200 (10'6'') 3400 (11'2'') 3600 (11'10'')
Treads (front and rear) mm (ft.in) 2145 (7'') 2400 (7'10'') 2800 (9'2'')
Articulation angle degree 38 40 40
ENGINE:
Model KOMATSU KOMATSU KOMATSU
SA6D108E SA6D125E SA6D140E
No. of cylinders- mm (in) 6-108 × 130 6-125 × 150 6-140 × 165
bore × stroke (4.25 × 5.12) (4.92 × 5.91) (5.51 × 6.50)
Piston displacement ltr. (cu.in) 7.15 (436) 11.04 (674) 15.24 (928)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 287 (76) 390 (103) 465 (123)
3D-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
E F
JK
H
C I D
A
A B C D E F G H I J K L
mm mm mm mm mm mm mm mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
7520 3615 4100 3400 2350 3400 1050 475 1760 1900 1250 450
WF450T-3
(24'8") (11'10") (13'5") (11'2") (7'9") (11'2") (3'5") (1'7") (5'9") (6'3") (4'1") (1'6")
8145 4050 4550 3600 2600 3800 1200 500 1960 2005 1500 480
WF550T-3
(26'9") (13'3") (14'11) (11'10") (8'6") (12'6") (3'11") (1'8") (6'5") (6'7") (4'11") (1'7")
8925 4430 5200 4100 2900 4300 1400 525 2400 2250 1560 580
WF650T-3
(29'3") (14'6") (17'1") (13'5") (9'6") (14'1") (4'7") (1'9") (7'10") (7'5") (5'1") (1'11")
Trash loader
G
E F
45o
L
J
K B
G.L. H
I D
C
A
A B C D E F G H I J K L M
mm mm mm mm mm mm mm mm mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
8020 3375 2915 3200 2145 2845 700 450 2835 4090 3070 1120 6730
WF350-3
(26'4") (11'1") (9'7") (10'6") (7') (9'4") (2'4") (1'6") (9'4") (13'5") (10'1") (3'8") (22'1")
8825 3455 3405 3400 2400 3290 850 475 3065 4340 3250 1210 6955
WF450-3
(28'11") (11'4") (11'2") (11'2") (7'10) (10'10") (2'9") (1'7") (10'1") (14'3") (10'8") (4'0") (22'10")
9580 3905 4145 3600 2800 3900 1100 500 3190 4545 3380 1275 7595
WF550-3
(31'5") (12'10") (13'7") (11'10") (9'2") (12'10") (3'7") (1'8") (10'6") (14'11") (11'1") (4'2") (24'11")
3D-4
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 3E
TOWING TRACTORS
(FOR AIRPLANE)
CONTENTS
Features .................................................................... 3E-2
Specifications ........................................................... 3E-3
Dimensions ............................................................... 3E-4
3E-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
3E-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
WT250E-1 WT500E-1
Item
WEIGHT: kg (lb)
Operating weight 25000 (55,130) 50000 (110,250)
Distribution (front) 12500 (27,560) 25000 (55,130)
(rear) 12500 (27,560) 25000 (55,130)
FLYWHEEL HORSEPOWER HP (kW)/rpm 217 (162)/2400 304 (227)/2200
PERFORMANCE:
Maximum drawbar pull kg (lb) 20000 (44,100) 38000 (83,770)
Travel speeds: km/h (MPH)
Forward 1st 7.0 (4.3) 3.6 (2.2)
2nd 12.5 (7.8) 9.0 (5.6)
3rd 22.3 (13.9) 20.0 (12.4)
4th 33.8 (21.0) 30.0 (18.6)
Reverse 1st 7.4 (4.6) 3.6 (2.2)
2nd 13.2 (8.2) 9.0 (5.6)
3rd 23.5 (14.6) 20.0 (18.6)
4th 35.3 (21.9) —
Turning radius (4ws) mm (ft.in) 6600 (21'8") 6500 (21'4")
(2ws) 10000 (32'10") 10000 (32'10")
DIMENSIONS:
Overall length mm (ft.in) 7670 (25'2") 8345 (27'5")
Overall width mm (ft.in) 2900 ( 9'6") 2930 ( 9'7")
Overall height* mm (ft.in) 2945 ( 9'8") 2950 ( 9'8")
Wheelbase mm (ft.in) 3300 (10'10") 3500 (11'6")
Treads (front and rear) mm (ft.in) 2250 ( 7'5") 2440 (8')
Minimum ground clearance mm (in) 250 ( 9.8") 210 ( 8.3")
ENGINE: KOMATSU KOMATSU
Model SA6D108 S6D125
No. of cylinders- mm (in) 6-108 × 130 6-125 × 150
bore × stroke (4.25 × 5.12) (4.92 × 5.90)
Piston displacement ltr. (cu.in) 7.15 (436) 11.04 (673)
TIRES:
Front tire 14.00-25-20PR 16.00-25-32PR
Rear tire 14.00-25-20PR 16.00-25-32PR
CAPACITY:Fuel tank ltr. (U.S. Gal) 300 (79.3) 300 (79.3)
* To top of yellow warning lamp
3E-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
WT250E-1
Unit: mm (ft.in)
WT500E-1
Unit: mm (ft.in)
3E-4
CONTENTS
SECTION 4
INDEX
SECTION 4A
OFF-HIGHWAY
DUMP TRUCKS
CONTENTS
Features .................................................................... 4A-2
Specifications ........................................................... 4A-5
Dimensions ............................................................... 4A-8
Use of performance curve ..................................... 4A-10
Performance curve
HD255-5 .............................................................. 4A-11
HD325-6 .............................................................. 4A-13
HD325-6 4WD ..................................................... 4A-15
HD405-6 .............................................................. 4A-17
HD465-7 .............................................................. 4A-19
HD605-7 .............................................................. 4A-21
HD785-5 .............................................................. 4A-23
HD985-5 .............................................................. 4A-27
HD1200-1 ............................................................ 4A-29
HD1500-5 ............................................................ 4A-30
630E .................................................................... 4A-31
730E .................................................................... 4A-32
830E .................................................................... 4A-33
930E-3 ................................................................. 4A-34
Attachments and options ...................................... 4A-35
Tire selection ......................................................... 4A-39
Body selection ...................................................... 4A-42
Production ............................................................. 4A-53
4A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features OFF-HIGHWAY
DUMP TRUCKS
High productivity
The result of total performance: High performance,
minimum downtime, and easy operation
Dependable and high-performance
components
• Komatsu diesel engine delivers high-output and
direct injection system provides high fuel
efficiency
• Full-automatic TORQFLOW transmission:
A microcomputer built into the shift controller
automatically selects the optimum gear position
according to travel speed, load and road
conditions assuring effort-free operation.
• High-performance, durable brakes: Sealed, oil-
cooled, multiple-disc brakes on rear wheels are
designed for extended operation. The large-
capacity rear wheel brakes also act as retarders
as a precaution against engine overrunning when
descending steep inclines.
• High maneuverability: The MacPherson strut type
front suspension system has a special A-frame
between each wheel and the main frame. The
wider space created between the front wheels
and the main frame increases the turning angle of
the wheels. The larger this turning angle, the
smaller the turning radius of the truck.
• Extra sturdiness: Box-section, ladder type frame
construction of high-tensile-strength steel plate
and cast steel offer unfaltering durability for long
service.
4A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Features OFF-HIGHWAY
DUMP TRUCKS
Easy operation/operator comfort
• K-ATOMICS for extra-smooth ride
K-ATOMICS stands for "Komatsu - Advanced
Transmission with Optimum Modulation Control
System" that consists of the computer, sensors
and electronically controlled modulation valve
(ECMV) fitted to each clutch. The computer
sophisticatedly controls hydraulic pressure of
clutches in the planetary gear transmission
through ECMV, making clutch engagement /
disengagement smooth and shock-free. Results
are smooth, continuous acceleration and
deceleration without the shocks and interruption
of continuous torque rise/drop.
• High traveling stability:
Nitrogen gas
Hydro-pneumatic suspension, low center of
gravity, long wheelbase and wide treads all
ensure excellent stability and greater operator
comfort.
• Comfortable hydro-pneumatic
suspension:
Employed on four wheels. As the load from the
body and the ground increases the displacement
difference becomes greater. When heavy loads
are added, the hydro-pneumatic system oscillates
with longer strokes to absorb the extra shock.
This efficient cushioning function contributes to
greater comfort, higher stability and extended
durability.
• Low loading height and large target area:
The newly designed body has large target area
and a low loading height, for easier loading and
shortened loading cycles.
• Ideal driving position settings:
The 5-way adjustable operator seat and the tilt-
telescopic steering column create an optimum
driving posture, for increased driving comfort and
more control over the machine's operations.
job sites
In comparison with 2WD models, the superior 4WD
mobility of the 4WD truck on soft-terrain dumping
sites means reduced dozing work.
50 60 70 80 90 100%
4A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Internet
Personal
computer terminal
WebCARE Server (for downloading
data)
Komatsu
distributors
Recommendation
• An appropriate recommendation can be made by viewing these data over the Internet.
• Proper driving methods
• Formulation of maintenance plans in advance that suit the customer's production schedule.
Customer's Benefit
• Sudden break down can be prevented through utilization of data trend (change over time).
• Ascertaining the facts and searching for the cause of the breakdown are simplified, thus enabling
problems to be resolved quickly.
• Down time can be shortened by the systematic use of Reman components.
• Machine life can be extended significantly by proper operation and proper maintenance.
4A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Specifications OFF-HIGHWAY
DUMP TRUCKS
1. Japan source
Model
HD255-5 HD325-6 HD325-6 4WD
Item
WEIGHT: kg (lb)
Empty vehicle weight* 22950 (50,600) 28700 (63,270) 30740 (67,770)
Distribution (front) 11020 (24,290) 13780 (30,380) 15060 (33,200)
(rear) 11930 (26,300) 14920 (32,890) 15380 (33,910)
Gross vehicle weight 48030 (105,890) 60780 (134,000) 62820 (138,490)
Distribution (front) 15370 (33,880) 19450 (42,880) 20730 (45,700)
(rear) 32660 (72,000) 41330 (92,120) 42090 (92,790)
Max. gross vehicle weight** — 65200 (143,740) 67320 (148,410)
Gross horsepower HP (kW)/RPM 323 (241)/2100 508 (379)/2000 508 (379)/2000
Flywheel horsepower HP (kW)/RPM 316 (235)/2100 488 (364)/2000 488 (364)/2000
HAULING CAPACITY:
Maximum load m. ton (U.S. ton) 25 (27.6) 36.5 (40) 36.5 (40)
Heaped capacity (2:1) m3 (yd3) 17.7 (23.2) 24 (31.4) 24 (31.4)
PERFORMANCE:
Maximum speed km/h (MPH) 47.5 (29.5) 70 (43.5) 68 (42.3)
Turning radius m (ft.in) 7.0 (23') 7.2 (23'7") 7.2 (23'7")
ENGINE: KOMATSU KOMATSU KOMATSU
Model SAA6D125E SAA6D140E SAA6D140E
No. of cylinders- 6 6 6
bore × stroke mm (in) 125 × 150 140 × 165 140 × 165
(4.92 × 5.91) (5.51 × 6.50) (5.51 × 6.50)
Displacement ltr. (in3) 11.04 (674) 15.23 (930) 15.23 (930)
DIMENSION: See DIMENSIONS
TIRES:
Front tire 16.00R25 × 2 18.00-33-28PR × 2 18.00-R33 × 2
Rear tire 16.00R25 × 4 18.00-33-28PR × 4 18.00-R33 × 4
CAPACITY: Fuel tank ltr. (U.S. Gal) 374 (98.8) 500 (132.0) 500 (132.0)
Model
HD405-6 HD465-7 HD605-7
Item
WEIGHT: kg (lb)
Empty vehicle weight* 32050 (70,660) 42800 (94,360) 45900 (101,190)
Distribution (front) 14420 (31,790) 20120 (44,360) 21575 (47,560)
(rear) 17630 (38,870) 22680 (50,000) 24325 (53,630)
Gross vehicle weight 72125 (159,010) 97875 (215,780) 108975 (240,250)
Distribution (front) 22850 (50,380) 31320 (69,050) 34870 (76,870)
(rear) 49275 (108,630) 66555 (146,730) 74105 (163,370)
Max. gross vehicle weight** 73175 (161,320) 98800 (217,810) 109900 (242,290)
Gross horsepower HP (kW)/RPM 508 (379)/2000 739 (551)/2000 739 (551)/2000
Flywheel horsepower HP 488 (364)/2000 715 (533)/2000 715 (533)/2000
HAULING CAPACITY:
Maximum load m. ton (U.S. ton) 41 (45) 55 (61) 63 (69)
Heaped capacity (2:1) m3(yd3) 27.3 (35.7) 34.2 (44.7) 40 (52.3)
PERFORMANCE:
Maximum speed km/h (MPH) 70 (43.5) 70 (43.5) 70 (43.5)
Turning radius m (ft.in) 7.2 (23'7") 8.5 (27'11") 8.5 (27'11")
ENGINE: KOMATSU KOMATSU KOMATSU
Model SAA6D140E SAA6D170E SAA6D170E
No. of cylinders- 6 6 6
bore × stroke mm (in) 140 × 165 170 × 170 170 × 170
(5.91 × 6.50) (6.69 × 6.69) (6.69 × 6.69)
Displacement ltr. (in3) 15.23 (930) 23.15 (1.413) 23.15 (1413)
DIMENSION: See DIMENSIONS
TIRES:
Front tire 18.00R33 × 2 24.00-35-36PR × 2 24.00R35 × 2
Rear tire 18.00R33 × 4 24.00-35-36PR × 4 24.00R35 × 4
CAPACITY: Fuel tank ltr. (U.S. Gal) 500 (132.0) 780 (206.1) 780 (206.1)
* Weight includes lubricants, coolant, full fuel tank and standard body.
** Max. gross vehicle weight, including optional equipment, lubricants, coolant, full fuel tank and payload, with large tires installed,
shall not be exceeded .
4A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Specifications OFF-HIGHWAY
DUMP TRUCKS
Model
HD785-5 HD985-5 HD1200-1*5
Item
WEIGHT: kg (lb)
Empty vehicle weight* 66930 (147,550) 73700 (162,480) 100880 (222,400)
Distribution (front) 31460 (69,360) 34640 (76,370) 46730 (103,020)
(rear) 35470 (78,200) 39060 (86,110) 54150 (119,380)
Gross vehicle weight 158005 (348,340) 173780 (383,120) 236880 (52,230)
Distribution (front) 52140 (114,950) 57345 (126,420) 79380 (175,000)
(rear) 105865 (233,390) 116435 (256,690) 157500 (347,220)
Max. gross vehicle weight** 166000 (366,000) 178780 (394,140) —
Gross horsepower HP (kW)/RPM 1050 (783)/2000 1050 (783)/2100 1200 (895)/2100
Flywheel horsepower HP (kW)/RPM 1010 (753)/2000 1010 (753)/2100 1160 (865)/2100
HAULING CAPACITY:
Maximum load m. ton (US ton) 91 (100) 105 (116) 136 (150)
Heaped capacity (2:1) m3 (yd3) 60 (78.5) 64 (83.7) 78 (102.0)
PERFORMANCE:
Maximum speed km/h(MPH) 65 (40.4) 70 (43.5) 57.5 (35.7)
Turning radius m (ft.in) 9.9 (32'6") 12.5 (41') 12.5 (41')
ENGINE: KOMATSU KOMATSU CUMMINS
Model SA12V140 SA12V140 KTA-38-C1200
No. of cylinders- 12 12 12
bore × stroke mm (in) 140 × 165 140 × 165 159 × 159
(5.51 × 6.50) (5.51 × 6.50) (6.26 × 6.26)
Displacement ltr. (in3) 30.48 (1860) 30.48 (1860) 37.7 (2300)
DIMENSION: See DIMENSIONS
TIRES:
Front tire 27.00R49** × 2 30.00 R51** × 2 33.00-51-58PR × 2
Rear tire 27.00R49** × 4 30.00 R51** × 4 33.00-51-58PR × 4
CAPACITY: Fuel tank ltr.(U.S. Gal) 1250 (330.3) 1250 (330.3) 1900 (502.0)
* Weight includes lubricants, coolant, full fuel tank and standard body.
** Max. gross vehicle weight, including optional equipment, lubricants, coolant, full fuel tank and payload, with large tires installed,
shall not be exceeded .
*5 136 tons payload
4A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Specifications OFF-HIGHWAY
DUMP TRUCKS
2. USA source
Model
HD785-5 HD1500-5 630E***
Item
WEIGHT: kg (lb)
Empty vehicle weight* 69933 (154,178) 100462 (221,481) 124028 (273,430)
Distribution (front) 33568 (74,005) 49025 (108,082) 60215 (132,750)
(rear) 36365 (80,173) 51437 (113,399) 63812 (140,680)
Gross vehicle weight 166468 (367,000) 249476 (550,000) 294840 (650,000)
Distribution (front) 54102 (119,275) 82327 (181,500) 91396 (201,490)
(rear) 112366 (247,725) 167149 (368,500) 203444 (448,510)
Max. gross vehicle weight** 166468 (367,000) 249476 (550,000) 294840 (650,000)
Gross horsepower HP (kW)/RPM 1082 (807)/2000 1486 (1108)/1900 2000 (1492)/1900
Flywheel horsepower HP (kW)/RPM 1042 (777)/2000 1406 (1048)/1900 1860 (1388)/1900
HAULING CAPACITY:
Maximum load m. ton (US ton) 90.72 (100) 149 (164) 172 (190)
Heaped capacity (2:1) m3 (yd3) 60.1(78.7) 78 (102) 103 (135)
PERFORMANCE:
km/h (MPH)
Maximum speed 61.9 (38.5) 58 (36.0) 51.0 (31.7)
m (ft.in)
Turning radius 9.9 (32'6") 12.2 (40') 12.2 (40')
ENGINE: KOMATSU KOMATSU KOMATSU
Model SAA12V140ZE2 SDA12V160 SSA16V159
No. of cylinders- 12 12 16
bore × stroke mm (in) 140 × 165 159 × 190 159 × 159
(5.51 × 6.50) (5.26 × 7.48) (5.26 × 5.26)
Displacement ltr. (in3) 30.48 (1860) 45.0 (2746) 50.3 (3069)
DIMENSION: See DIMENSIONS
TIRES:
Front tire 27.00-R49 × 2 33.00-R51 × 2 36.00-51 × 2
Rear tire 27.00-R49 × 4 33.00-R51 × 4 36.00-51 × 4
CAPACITY: Fuel tank ltr. (U.S. Gal) 1250 (330) 2120 (560) 3217 (850.0)
Model
730E 830E 930E-3***
Item
WEIGHT: kg (lb)
Empty vehicle weight* 138369 (305,052) 158159 (349,136) 208580 (459,836)
Distribution (front) 66160 (145,858) 78638 (173,593) 102830 (226,699)
(rear) 72209 (159,194) 79521 (175,543) 105750 (233,137)
Gross vehicle weight 324318 (715,000) 385848 (850,650) 498957 (1,100,000)
Distribution (front) 98941 (218,129) 127330 (280,715) 164656 (363,000)
(rear) 225377 (496,871) 258518 (569,935) 334301 (737,000)
Max. gross vehicle weight** 324318 (715,000) 385848 (850,650) 498957 (1,100,000)
Gross horsepower HP (kW)/RPM 2000 (1492)/1900 2500 (1865)/1900 2700 (2014)/1900
Flywheel horsepower HP (kW)/RPM 1860 (1388)/1900 2360 (1761)/1900 2550 (1902)/1900
HAULING CAPACITY:
Maximum load m. ton (US ton) 186 (205) 231 (255) 290 (320)
Heaped capacity (2:1) m3 (yd3) 111 (145) 147 (193) 211 (276)
PERFORMANCE:
Maximum speed km/h (MPH) 55.7 (34.6) 48.8 (30.3) 64.5 (40)
Turning radius m (ft.in) 14.0 (46') 14.2 (46'5") 15.2 (48'9")
ENGINE: KOMATSU KOMATSU KOMATSU
Model SSA16V159 SSDA16V160 SSDA16V160
No. of cylinders- 16 16 16
bore × stroke mm (in) 159 × 159 160 × 190 160 x 190
(5.26 × 5.26) (5.26 × 7.48) (6.26 x 7.48)
Displacement ltr. (in3) 50.3 (3069) 64.9 (3968) 60.2 (3674)
DIMENSION: See DIMENSIONS
TIRES:
Front tire 37.00-R57 × 2 40.00-57 × 2 53/80-R63 x 2
Rear tire 37.00-R57 × 4 40.00-57 × 4 53/80-R63 x 4
CAPACITY: Fuel tank ltr. (U.S. Gal) 3217 (850.0) 4542 (1200) 4542 (1200)
* Weight includes lubricants, coolant, full fuel tank and standard body.
** Max. gross vehicle weight, including optional equipment, lubricants, coolant, full fuel tank and payload, with large tires installed,
shall not be exceeded.
*** Weight includes lubricants, coolant, 50% fuel tank and standard body. Max. gross vehicle weight, including optional equipment,
lubricants, coolant, 50% fuel tank and payload, with large tires installed, shall not be exceeded.
4A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Dimensions OFF-HIGHWAY
DUMP TRUCKS
K N
C G
M
S
B
R
Q
H P
D E
J A
Unit: mm (ft.in)
HD325-6
HD255-5 HD325-6 HD405-6 HD465-7 HD605-7 HD785-5 HD785-5** HD985-5
4WD
18.00-33- 24.00-35-
Tires 16.00-R25 18.00-R33 18.00-R33 24.00-R35 27.00-R49 27.00-R49 30.00-R51
28PR 36PR
7390 8365 8365 8365 9355 9355 10490 10620 10610
A
(24'3") (27'5") (27'5") (27'5") (30'8") (30'8") (34'5") (34'10") (34'10")
3625 4150 4150 4150 4400 4400 5050 5270 5120
B*
(11'11") (13'7") (13'7") (13'7") (14'5") (14'5") (16'7") (17'3") (16'3")
3200 3660 3660 3660 4170 4170 5210 5430 5210
C
(10'6") (12') (12') (12') (13'8") (13'8") (17'1") (17'10") (17'1")
3600 3750 3750 3750 4300 4300 4950 4950 4950
D
(11'10") (12'4") (12'4") (12'4") (14'1") (14'1") (16'3") (16'3") (16'3")
2140 2630 2630 2630 3070 3070 3390 3370 3510
E
(7') (8'8") (8'8") (8'8") (10'1") (10'1") (11'1") (11'1") (11'6")
495 480 480 480 480 490 450 430 350
G
(1'7") (1'7") (1'7") (1'7") (1'7") (1'7") (1'6") (1'5") (1'2")
410 500 500 500 645 645 875 810 875
H
(1'4") (1'8") (1'8") (1'8") (2'1") (2'1") (2'10") (2'8") (2'10")
2700 3150 3190 3150 3515 3515 4230 4230 4420
J
(8'10") (10'4") (10'6") (10'4") (11'6") (11'6") (13'11") (13'11") (14'6")
2225 2550 2550 2550 3080 3080 3500 3500 3720
K
(7'4") (8'4") (8'4") (8'4") (10'1") (10'1") (11'6") (11'5") (12'2")
4570 5500 5500 5590 6450 6600 7480 7760 7550
M
(15') (18'1") (18'1") (18'4") (21'2") (21'8") (24'7") (25'5") (24'9")
2995 3380 3380 3380 3870 3870 4880 4990 4870
N
(9'10") (11'1") (11'1") (11'1") (12'8") (12'8") (16') (16'4") (16')
560 530 530 530 560 560 810 800 855
P
(1'10") (1'9") (1'9") (1'9") (1'10") (1'10") (2'8") (2'7") (2'10")
49° 48° 48° 48° 48° 48° 48° 45° 47°
Q
2975 3200 3200 3430 3600 3860 4285 4290 4545
R
(9'9") (10'6") (10'6") (11'3") (11'10") (12'8") (14'1") (14'1") (14'11")
7110 7885 7885 7885 8800 8800 10080 10210 10135
S
(23'4") (25'10") (25'10") (25'10") (28'10") (28'10") (33'1") (33'6") (33')
* Includes canopy spill guard.
** USA source
4A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Dimensions OFF-HIGHWAY
DUMP TRUCKS
K N
C G
M
S
B
R
Q
H P
D E
J A
Unit: mm (ft.in)
HD1200-1** HD1500-5 630E 730E 830E 930E-3***
33.00-51-
Tires 33.00-R51 36.00-51 37.00R57 40.00R57 53/80R63
58PR
10980 11370 11940 12830 14150 15320
A
(36') (37'4") (39'2") (42'1") (46'5") (50'3")
5550 5850 6430 6250 6880 7320
B*
(18'2") (19'2") (21'1") (20'6") (22'7") (24'0")
5800 6090 6650 7250 7260 8690
C
(19') (20'0") (21'10") (23'9") (23'10") (28'6")
5400 5400 5440 5890 6350 6350
D
(17'9") (17'9") (17'10") (19'4") (20'10") (20'10")
3180 3495 3420 3660 3960 4500
E
(10'5") (11'6") (11'3") (12'0") (13'0") (14'9")
450 530 360 290 60 —
G
(1'6") (1'9") (1'2") (1'0") (2") —
780 889 1260 1140 1280 940
H
(2'7") (2'11") (4'2") (3'9") (4'2") (3'1")
5016 5010 5540 5570 5770 6150
J
(16'5") (16'5") (18'2") (18'3") (18'11") (20'2")
4100 4020 4420 4680 4880 5300
K
(13'5") (13'2") (14'6") (15'4") (16'0") (17'4")
7740 7625 7980 8430 9190 9950
M
(25'5") (25'0") (26'2") (27'8") (30'2") (32'7")
5460 5705 6270 6850 6860 8150
N
(17'11") (18'9") (20'4") (22'6") (22'6") (26'9")
1770 1650 1290 1760 1840 1750
P
(5'10") (5'5") (4'3") (5'9") (6'0") (5'9")
47° 45° 45° 45° 45° 45°
Q
4650 4965 5840 5610 6710 7010
R
(15'3") (16'3") (19'2") (18'5") (22'0") (23'0")
11370 11440 11980 12510 13410 13990
S
(37'3") (37'6") (39'4") (41'1") (44'0") (45'11")
* Includes canopy spill guard.
** 136 tons payload
*** 120 tons payload, deep pit type
4A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
0 10 20 30 40 50 60 70 80 90 100 ton
EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
(A)
-30
-25
F1
-20
F2 -15
F3
-10
F4 (B)
(C) F5
F6
F7 -5
(D)
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
VEHICLE SPEED
FVBH0068A
4A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
HD255-5 OFF-HIGHWAY
Performance Curve DUMP TRUCKS
Travel Performance Curve
US ton
kN
Ton
GROSS WEIGHT
500 50 25 35 45 55 65
500 US ton
450 400 40 20 30 40 50 60
400 Ton
UNLOADED LOADED
30
ENGINE SPEED (rp m )
2600 300
300
TOTAL RESISTANCE (GRADE+ROLLING)%
45.0
200 20 40.0
200
35.0
30.0
1600 25.0
100 10
20.0
100 90 9
90 80 8
80 70 7 15.0
70 6 Transmision 13.0
60 12.0
60 F1 3.750
50 5 DIFF 3.900 F2 2.651
600 50 10.0
FINAL 4.941 F3 1.957 9.0
40 4
RD,RA 0.700 F4 1.384 8.0
40 7.0
F5 1.000
30 3 F6 0.707 6.0
30
R1 4.149 5.0
20 2 4.0
20
RIMPUL L
3.0
10 10 1 2.0
0.9
0.8
0.7
0.6
0.5
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
Brake performance
-30 -30
(GRADE+ROLLING)%
(GRADE+ROLLING)%
TOTAL RESISTANCE
TOTAL RESISTANCE
-25 -25
F1
-20 -20
F1
F2
-15 -15
F2 F3
F4
F3 -10 -10
F5
F4 F6
F5 -5
-5
F6
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
4A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
HD255-5 OFF-HIGHWAY
Performance Curve DUMP TRUCKS
Brake performance
GRADE DISTANCE: 600 m (2,000 ft) GRADE DISTANCE: 900 m (3,000 ft)
-30 -30
(GRADE+ROLLING)%
(GRADE+ROLLING)%
TOTAL RESISTANCE
TOTAL RESISTANCE
-25 -25
F1 F1
-20 -20
F2 F2
-15 -15
F3
F3
F4 -10 F4 -10
F5
F5
F6 F6
-5 -5
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
-30
(GRADE+ROLLING)%
TOTAL RESISTANCE
-25
-20
F1
F2 -15
F3
-10
F4
F5
F7 -5
F6
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
TRAVEL SPEED
FVBH0341
4A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
HD325-6 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
US ton
ton
55
50
50 GROSS WEIGHT
45 40 30 40 50 60 70 80 90 100
40 US ton
20 30 40 50 60 70 80 90 100
30 ton
ENGINE SPEED RPM
2600
30 UNLOADED LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
40.0
35.0
20
30.0
20
25.0
20.0
1600
10 15.0
10 9 14.0
9 8 13.0
12.0
8 7 11.0
7 10.0
6 9.0
6 8.0
5
600 5 7.0
4 6.0
4
RIMPULL
5.0
3
3 4.0
2 3.0
2
2.0
1 1
0.9
0.8
0.7
0.6
0.5
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
TRAVEL SPEED
FKH00151
Brake performance
-25 -25
F1
F1 F2
-20 -20
F2
-15 F3 -15
F4
F3
-10 F5 -10
F6
F4 F7
F5
F6 -5 -5
F7
0 10 20 30 40 50 60 0 10 20 30 40 50 60 MPH
MPH
4A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
HD325-6 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Brake performance
Distance: 600 m (1970 ft) Distance: 900 m (2950 ft)
GROSS VEHICLE WEIGHT GROSS VEHICLE WEIGHT
0 10 20 30 40 50 60 70 80 90 100 110 USton 0 10 20 30 40 50 60 70 80 90 100 110 USton
-25 -25
F1
F1
F2 -20 -20
F2
F3 -15 -15
F3
F4
F5 -10 F4 -10
F6 F5
F7 F6
-5 F7 -5
0 10 20 30 40 50 60 70 80 90 100 ton
EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(% )
-30
Optional exhaust retarder
-25
F1
-20
F2
-15
F3
F4 -10
F5
F6
F7 -5
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
VEHICLE SPEED
FVBH0068
4A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
kN
ton
55 500 50
50 GROSS WEIGHT
45 400 40 30 40 50 60 70
40 US ton
20 30 40 50 60 70 ton
300 30
30 EMPTY 32Ton(35US Ton)LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
200 20 30.0
20
25.0
20.0
100 10 15.0
10 90 9 14.0
13.0
R IMP U L L
9 80 8 12.0
8 70 7 11.0
7 10.0
60 6 9.0
6 F1(T/C) 8.0
50 5
5 7.0
40 4 F1(D) 6.0
4
5.0
30 3 F2(T/C)
3 F2(D) 4.0
20 2 F3(D) 3.0
2
2.0
1 10 1
0.9
0.8
0.7
0.6
0.5
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
Brake performance
-30 -30
Optional exhaust retarder
Optional exhaust retarder
-25 -25
F1
-20 -20
F1
F2
-15 -15
F2 F3
F4
F3 -10 F5 -10
F4 F6
F5 F7
F6 F7 -5 -5
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
FVBH0059 FVBH0060
4A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
-30 -30
Optional exhaust retarder Optional exhaust retarder
-25 -25
F1 F1
-20
-20
F2 F2 -15
-15
F3 F3
F4 -10 F4 -10
F5 F5
F6 F6
F7 F7 -5
-5
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
0 10 20 30 40 50 60 MPH
VEHICLE SPEED
VEHICLE SPEED
FVBH0061 FVBH0062
0 10 20 30 40 50 60 70 80 90 100 ton
EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
-30
Optional exhaust retarder
-25
F1 -20
-15
F2
F3
-10
F4
F5
F6 -5
F7
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
VEHICLE SPEED
FVBH0063
4A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
HD405-6 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
US ton
ton
55
50
50 GROSS WEIGHT
45 40 40 50 60 70 80 90 100
40 US ton
30 40 50 60 70 80 90 100
30 ton
ENGINE SPEED RPM
2600
UNLOADED LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(% )
30
35.0
30.0
20
20 25.0
20.0
1600
15.0
10 14.0
10 9 13.0
12.0
9 8 11.0
8 7 10.0
7 9.0
6 8.0
6
5 7.0
600 5 6.0
4
5.0
RIMPUL L
4
3 4.0
3
3.0
2
2
2.0
1 1
0.9
0.8
0.7
0.6
0.5
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
Brake performance
-30 -30
Optional exhaust retarder
-25 -25
F1 F1
F2
-20 -20
F2
-15 F3 -15
F4
F3
-10 F5 -10
F6
F4 F7
F5
F6 -5 -5
F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
4A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
HD405-6 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Brake performance
F1
-25 -25
F1
F2 -20 -20
F2
F3 -15 -15
F3
F4 F4
F5 -10 -10
F5
F6 F6
F7 F7
-5 -5
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
0 10 20 30 40 50 60 70 80 90 100 ton
EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
F1
-25
-20
F2
-15
F3
F4 -10
F5
F6
F7 -5
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
VEHICLE SPEED
FVBH0073
4A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
HD465-7 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
ton
US ton
50
50 40 50 60 70 80 90 100 110120 US ton
40
40 40 50 60 70 80 90 100 110120 ton
30
30
20 20.0
20
15.0
13.0
11.0
10 10.0
10 9.0
8 8.0
8 7.0
6 6.0
6 5 20.
5.0
5 04.0
4
4
3 3.0
3
2.0
2
2
1
1
0.5
0 10 20 30 40 50 60 70 km/h
0 5 10 15 20 25 30 35 40 45 MPH
FVBH0150
Brake performance
0 20 40 60 80 100 120 140 160 180 200 220 US ton 0 20 40 60 80 100 120 140 160 180 200 220 US ton
EMPTY LOADED EMPTY LOADED
-40 -35 -30 -25 -40 -35 -30 -25
-20 -20
TOTAL RESISTANCE (GRADE+ROLLING)(%)
TOTAL RESISTANCE (GRADE+ROLLING)(%)
F1
-15 -15
F1
F2
F2 -10
F3 -10
F3 F4
F5
F4 F6
-5 F7 -5
F5
F6
F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
4A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
HD465-7 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Brake performance
Grade distance: 600 m (2,000 ft) Grade distance: 900 m (3,000 ft)
0 20 40 60 80 100 120 140 160 180 200 220 US ton 0 20 40 60 80 100 120 140 160 180 200 220 US ton
EMPTY LOADED EMPTY LOADED
-40 -35 -30 -25 -40 -35 -30 -25
-20 -20
TOTAL RESISTANCE (GRADE+ROLLING)(%)
F1 -15 -15
F1
F2
F2
-10 -10
F3
F3
F4
F4
F5
F6 F5
-5 -5
F7 F6
F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
-15
F1
F2
-10
F3
F4
F5 -5
F6
F7
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
4A-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
HD605-7 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
ton
US ton
50
50 40 50 60 70 80 90 100 110120 US ton
40
40 40 50 60 70 80 90 100 110120 ton
30
30
20.0
20
20 15.0
13.0
11.0
10.0
10 9.0
10 8.0
8 7.0
8
6.0
6
6 5 20.
5.0
5 04.0
4
4 3.0
3
3
2.0
2
2
1
1
0.5
0 10 20 30 40 50 60 70 km/h
0 5 10 15 20 25 30 35 40 45 MPH
FVBH0156
Brake performance
0 20 40 60 80 100 120 140 160 180 200 220 US ton 0 20 40 60 80 100 120 140 160 180 200 220 US ton
EMPTY LOADED EMPTY LOADED
-40 -35 -30 -25 -40 -35 -30 -25
-20 -20
TOTAL RESISTANCE (GRADE+ROLLING)(%)
TOTAL RESISTANCE (GRADE+ROLLING)(%)
F1
-15 -15
F1
F2
F2 -10
F3 -10
F3 F4
F5
F4 F6
-5 F7 -5
F5
F6
F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
4A-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
HD605-7 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Brake performance
Grade distance: 600 m (2,000 ft) Grade distance: 900 m (3,000 ft)
0 20 40 60 80 100 120 140 160 180 200 220 US ton 0 20 40 60 80 100 120 140 160 180 200 220 US ton
EMPTY LOADED EMPTY LOADED
-40 -35 -30 -25 -40 -35 -30 -25
-20 -20
TOTAL RESISTANCE (GRADE+ROLLING)(%)
TOTAL RESISTANCE (GRADE+ROLLING)(%)
F1 -15 -15
F1
F2
F2
-10 -10
F3
F3
F4
F4
F5
F5
F6 -5 -5
F7 F6
F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
-15
F1
F2
-10
F3
F4
F5 -5
F6
F7
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
4A-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
HD785-5 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
Brake performance
4A-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
HD785-5 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Brake performance
4A-24
AH_25.book Page 25 Tuesday, March 23, 2004 9:41 AM
HD785-5* OFF-HIGHWAY
Performance Curves DUMP TRUCKS
* USA sourced
Travel Performance Curve
Brake performance
0 50 100 150 200 250 300 350 400 450 lb x 1000 0 50 100 150 200 250 300 350 400 450 lb x 1000
TOTAL RESISTANCE (GRADE + ROLLING)(%)
5th GEAR
4th GEAR
6th GEAR
5th GEAR 7th GEAR
-5% -5%
6th GEAR
7th GEAR
0 5 10 15 20 25 30 35 40 45 50 mph 0 5 10 15 20 25 30 35 40 45 50 mph
0 10 20 30 40 50 60 70 80 km/h 0 10 20 30 40 50 60 70 80 km/h
4A-25
AH_25.book Page 26 Tuesday, March 23, 2004 9:41 AM
HD785-5* OFF-HIGHWAY
Performance Curves DUMP TRUCKS
* USA sourced
Brake performance
Grade distance: 600 m (2000 ft) Grade distance: 900 m (3000 ft)
0 50 100 150 200 250 300 350 400 450 lb x 1000 0 50 100 150 200 250 300 350 400 450 lb x 1000
TOTAL RESISTANCE (GRADE + ROLLING)(%)
0 5 10 15 20 25 30 35 40 45 50 mph 0 5 10 15 20 25 30 35 40 45 50 mph
0 10 20 30 40 50 60 70 80 km/h 0 10 20 30 40 50 60 70 80 km/h
4A-26
AH_25.book Page 27 Tuesday, March 23, 2004 9:41 AM
HD985-5 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
US ton
ton
60
TOTAL RESISTANCE (GRADE+ROLLING)(%)
30.0
50
50 25.0
40
40 20.0
30
30 15.0
14.0
1600 13.0
12.0
20 11.0
20 10.0
9.0
8.0
7.0
6.0
10
600 10 9 5.0
9 8
8 7 4.0
RIMPULL
7
6
6 3.0
5
5
4
4 2.0
3
3
2
2 1.0
1
0 10 20 30 40 50 6 0 km/h
0 10 15 20 25 30 35 40 45 MPH
Brake performance
Distance: Continuou
s Distance: 450 m (1500 ft)
GROSS VEHICLE WEIGHT GROSS VEHICLE WEIGHT
0 40 80 120 160 200 240 280 320 360 400 440 USton 0 40 80 120 160 200 240 280 320 360 400 440 USton
0 40 80 120 160 200 240 280 320 360 400 ton 0 40 80 120 160 200 240 280 320 360 400 ton
100ton(110US ton) 100ton(110US ton)
EMPTY LOADED -30 -25 EMPTY LOADED -30 -25
TOTAL RESISTANCE (GRADE+ROLLING)(%)
TOTAL RESISTANCE (GRADE+ROLLING)(%)
-20 -20
F2
F2 -10 -10
F3
F3 F4
F5
F4 -5
-5
F5 F6
F7
F6
F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
FVH00418 FVH00415
4A-27
AH_25.book Page 28 Tuesday, March 23, 2004 9:41 AM
HD985-5 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Brake performance
0 40 80 120 160 200 240 280 320 360 400 ton 0 40 80 120 160 200 240 280 320 360 400 ton
100ton(110US ton) 100ton(110US ton)
EMPTY LOADED -30 -25 EMPTY LOADED -30 -25
TOTAL RESISTANCE (GRADE+ROLLING)(%)
TOTAL RESISTANCE (GRADE+ROLLING)(%)
-20 -20
F2
F2 -10 -10
F3 F3
F4 F4
F5 F5
-5 -5
F6 F6
F7 F7
0 10 20 30 40 50 60 MPH 0 10 20 30 40 50 60 MPH
FVH00414 FVH00413
-20
With optional
F1 exhaust retader -15
F2
-10
F3
F4
F5 -5
F6
F7
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
VEHICLE SPEED
FVH00417
4A-28
AH_25.book Page 29 Tuesday, March 23, 2004 9:41 AM
HD1200-1 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel Performance Curve
Travel Speed
Brake performance
Travel Speed
4A-29
AH_25.book Page 30 Tuesday, March 23, 2004 9:41 AM
HD1500-5 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel performance
Travel Speed
Brake performance
Travel Speed
4A-30
AH_25.book Page 31 Tuesday, March 23, 2004 9:41 AM
630E OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel performance
Travel Speed
Brake performance
Travel Speed
4A-31
AH_25.book Page 32 Tuesday, March 23, 2004 9:41 AM
730E OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel performance
Travel Speed
Brake performance
Travel Speed
4A-32
AH_25.book Page 33 Tuesday, March 23, 2004 9:41 AM
830E OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel performance
Brake performance
4A-33
AH_25.book Page 34 Tuesday, March 23, 2004 9:41 AM
930E-3 OFF-HIGHWAY
Performance Curves DUMP TRUCKS
Travel performance
Travel Speed
Brake performance
Travel Speed
4A-34
AH_25.book Page 35 Tuesday, March 23, 2004 9:41 AM
Muffler
Radiator curtain
Differential lock
Three-way emergency brake
Optional tires
Transmission underguard
Mode selection system Engine underguard
Exhaust retarder Propeller shaft guard
Engine emergency shutoff system Vandalism protection kit
Water separator
Fast fill fuel system
Noise suppression kit
Air dryer
Air tank auto-drain valve
4A-35
AH_25.book Page 36 Tuesday, March 23, 2004 9:41 AM
Description Features
• Vehicle condition can be easily monitored to
confirm functions or perform troubleshooting
efficiently.
• Stored data can be downloaded through
customer provided personal computer with
PMC (power train management control) Komatsu PMC download software to transfer
the data to customer maintenance/production
database.
• Memory card type Payload meter (PLM2) data
can also be downloaded through the same PC
connection port. (HD785/HD985)
Auto Retard Speed Control (ARSC)
Payload meter
• The payload meter measures and records the
amount loaded, and also uses the external
display lamps to show the present payload and
to estimate the weight when the next bucket is
loaded, thereby informing the loader operator.
So it is possible to load the most suitable
amount and to avoid overloading.
• By knowing the production, it becomes
possible to carry out efficiency control of
combinations, and administration of economic
use of the machines.
Exhaust retarder
4A-36
AH_25.book Page 37 Tuesday, March 23, 2004 9:41 AM
Description Features
Three-way emergency brake
Differential lock
Body liner
Body extension
This extends the height of the side of the dump body. This
increases the capacity of the body to ensure the rated load
(For example: the capacity of the HD325-5 is 32 tons)
when handling loads with a low specific gravity.
It is also used to prevent spillage of load caused by
adverse travel conditions (rough road surface, uphill slope,
downhill slope, road with curves).
4A-37
AH_25.book Page 38 Tuesday, March 23, 2004 9:41 AM
Description Features
Muffler (without body heating)
Air dryer
4A-38
AH_25.book Page 39 Tuesday, March 23, 2004 9:41 AM
Model Tires size Code Remark Model Tires size Code Remark
16.00-25-28PR E-3, E-4 27.00-49-48PR E-3, E-4
HD785-5
HD255-5 16.00-25-32PR E-3, E-4 27.00R49 E-3, E-4
16.00R25 E-3, E-4 HD985-5 30.00R51 E-3, E-4
18.00-33-32PR E-3, E-4 30.00-51-46PR E-4
HD325-6 18.00-33-28PR E-3, E-4 30.00-51-50PR E-4
HD1200-1
18.00R33 E-3, E-4 * 30.00-51-58PR E-4
18.00 R 33 E-3, E-4 30.00R51 E-4
HD325-6 4WD
29.55R25 HD1500-5 33.00R51
HD405-6 18.00R33 E-3, E-4 36.00-51
630E
24.00-35-36PR E-3, E-4 36.00R51
HD465-7
24.00R35 E-3, E-4 730E 37.00R51
24.00R35 E-3, E-4 40.00-57
HD605-7 830E
24.00-35-48PR E-3, E-4 40.00R57
930E-3 53/80R63
NOTE: *When installing radial tires, please use the special rim for radial tire.
TMPH RATING
Where the ambient temperature in an operating environment is high or where a long haul or high-speed drive is required,
the standard tires are sometimes unsuitable because of their small TMPH.
Under the above operating conditions, it is recommended that the optimum tires be determined after obtaining TMPH by
applying the formulas stated in the section 15 and referring to the following table.
NOTE: The TMPH rating is based on U.S. ton (not on metric ton)
TMPH = TKPH ÷ 1.46
BRIDGESTONE TOYO
Model Tire size Code
Pattern HR STD CR Pattern HR SP CR CE
E-3 RL — — 139 G-18 — 175 145 —
HD255-5 16.00-25
E-4 RLS — — 111 G-18ET — 145 124 —
E-3 RL — 212 190 G-18 — 211 182 —
HD325-6
18.00-33 G-18ET — 167 145 —
HD405-6 E-4 ELS2 — 182 161
G-36ET — — 145 109
HD465-7 E-3 RL — 328 291 G-18 371 327 284 —
24.00-35
HD605-7 E-4 RLS 394 277 234 G-18ET 298 269 225 211
E-3 EL 701 — — G-18 611 — — —
HD785-5 27.00-49
E-4 ELS — 409 350 G-18ET 720 592 306 291
HD1200-1 33.00-51 E-4 ELS — 533 — G-18ET — 531 444 415
630E 36.00-51 E-4 ELS — 649 526 G-18ET 854 671 533 —
830E 40.00-57 E-4 — — — — G-18ET 948 693 591 —
NOTE: 1. The TKPH in the table is the value at 38°C an ambient temperature. (The value as of February, 2000.) When
the distance for the round trip exceeds 5 km, the tire life is governed by the travel conditions, so check with the
tire maker for details of the TKPH when selecting the tires.
2. The value for TKPH is reviewed from time to time by the tire maker, so consult the maker for the latest values.
3. For details of the TKPH value and tire specifications for conditions not given in this table, please consult the
tire maker.
4A-39
AH_25.book Page 40 Tuesday, March 23, 2004 9:41 AM
YOKOHAMA
Model Tire size Code
Pattern HR-H HR-V R-R R-T CR-S CR-C
E-3 Y67 153 139 129
HD255-5 16.00-25
E-4 Y523 131 117 102
E-3 Y67 255 — 212 233 190 —
HD325-6
18.00-33 Y523 219 — 182 197 153 —
HD405-6 E-4
Y523U — — 168 — 1117 146
HD465-7 E-3 Y87 379 — 314 343 — 277
24.00-35
HD605-7 E-4 Y523 321 — 263 292 175 226
E-3 Y67 584 642 481 525 — 409
HD785-5 27.00-49
E-4 Y523 452 495 387 416 263 336
HD1200-1 33.00-51 E-4 Y523 584 642 511 554 350 430
E-3 Y565 905 992 — — — —
Y523 888 751 569 627 379 461
630E 36.00-51
E-4 Y523R 888 751 569 627 379 461
Y535 730 802 620 686 423 526
830E 40.00-57 E-4 Y523 715 788 598 657 409 511
Table 2-1 TKPH for radial tire (for round trip of less than 5km)
BRIDGESTONE MICHELIN
Model Tire size Code
Pattern HR STD CR Pattern A4 A B4 B
E-3 — — — — XK — — — 187
HD255-5 16.00R25 VRLS 168 146 112 XHD1 105 128 — 175
E-4
VMTS 179 157 123 XKD1 — — — 162
XK — — — 279
E-3 VEL 307 263 213
HD325-6 XR — — — 305
18.00R33
HD405-6 XDT 157 — — 262
E-4 VRLS 246 211 170
XKD1 122 157 227
XK — — — 474
E-3 VEL 524 448 362
HD465-7 XR — — — 518
24.00R35
HD605-7 VRLS 453 388 314 XDT 266 — — 348
E-4
VRLS 453 388 314 XKD1 207 266 — 302
XK — — — 698
E-3 VRL 753 644 521
XR — — — 763
HD785-5 27.00R49
VRLS 600 513 415 XDT 392 — — 654
E-4
VMTS 702 600 486 XKD1 — 392 480 567
XK — — — 858
E-3 VMT 1065 911 737
XR — — — 938
HD985-5 30.00R51
XHD1 482 590 697 804
E-4 VRLS 717 603 496
XKD1 — 429 536 643
E-4 VRLS 807 690 558 XDT 558 — — 930
HD1500-5 33.00R51
E-4 VMTS 953 815 660 XKD1 — 496 620 744
XR — — — 1295
630E 36.00R51 E-4 VRLS 927 781 642 XK — — — 1184
XKD1 592 740 888
730E 37.00R51 E-4 VRLS 1003 845 694 XKD1 — — 678 1018
XKD1 — 768 960 1152
830E 40.00R57 E-4 VELS 1117 940 773
XKR1 — — — 1152
930E-3 53/80R63 E-4
NOTE: 1.The TKPH in the table is the value at 38°C an ambient temperature. (The value as of February 2000.) When the
distance for the round trip exceeds 5km, the tire life is governed by the travel conditions, so check with the tire
maker for details of the TKPH when selecting the tires.
2. The value for TKPH is reviewed from time to time by the tire maker, so consult the maker for the latest values.
3. For details of the TKPH value and tire specifications for conditions not given in this table, please consult the
tire maker.
4A-40
AH_25.book Page 41 Tuesday, March 23, 2004 9:41 AM
TOYO YOKOHAMA
Model Tire size Code
Pattern HR SP CR Pattern HR SP CR
E-3 — — — — — — — —
HD255-5 16.00R25
E-4 — — — — RB41 162 160 124
HD325-6 E-3 — — — — — — — —
18.00R33
HD405-6 E-4 T-432 218 167 124 — — — —
HD465-7 T-433 378 284 211 — — — —
24.00R35 E-4
HD605-7 T-452 349 255 196 — — — —
T-432 545 422 327 — — — —
HD785-5 27.00R49 E-4 T-433/ — — — —
516 393 305
T-452 — — — —
HD985-5 30.00R51 E-4 — — — 429 — — — —
HD1500-5 33.00R51 E-4 T-431 625 582 473 — — — —
630E 36.00R51 E-4 T-431 786 720 797 — — — —
730E 37.00R57 E-4 T-433 1018 844 676 — — — —
830E 40.00R57 E-4 — — — — — — — —
930E-3 53/80R63
NOTE: 1.The TKPH in the table is the value at 38°C an ambient temperature. (The value as of February 2000.) When the
distance for the round trip exceeds 5km, the tire life is governed by the travel conditions, so check with the tire
maker for details of the TKPH when selecting the tires.
2. The value for TKPH is reviewed from time to time by the tire maker, so consult the maker for the latest values.
3. For details of the TKPH value and tire specifications for conditions not given in this table, please consult the
tire maker.
4A-41
AH_25.book Page 42 Tuesday, March 23, 2004 9:41 AM
1 2 3 4
Selection Selection Selection
Selection of canopy of
of
of body spill guard tailgate
body
2) Rock body
• Rock body is suitable for job sites requiring
the handling of rocks such as macadam, in
limestone mines and for civil engineering etc.
• Total face of inner body is lined with steel
liners.
3) Rubber liner body
• Rubber liner body is suitable for job sites
where large diameter rocks such as ripraps
are loaded.
• Rubber liners are installed on the bottom face
of the body and steel liners are installed on
the other faces.
4A-42
AH_25.book Page 43 Tuesday, March 23, 2004 9:41 AM
4A-43
AH_25.book Page 44 Tuesday, March 23, 2004 9:41 AM
HD985-5
Model HD785-5
64m3 (83.7 yd3) 70m3(91.6 yd3)
Liner less Liner body Rubber liner Liner less Liner body Liner less Liner body
Body type
body (STD) (OP) body (OP) body (STD) (OP) body (STD) (OP)
Rock type x — —
Steel liner 4-face liner — — — — — — —
Liner
Half liner — — — — — —
Rubber liner t =105mm (4.1 in) x x x x x x
200mm (7.9 in) x x x x x x x
Body extension 250mm (9.8 in) x x x x x x x
300mm (11.8 in) x x x x x x x
150mm (5.9 in) — — — — — — —
200mm (7.9 in)
Canopy spill guard
250mm (9.8 in) — — — — — — —
300mm (11.8 in)
Tailgate ( ) ( ) x — — — —
4A-44
AH_25.book Page 45 Tuesday, March 23, 2004 9:41 AM
HD465-7
Rock body with 200 mm (7.9 in) body extension Plate thickness
No. Part
mm (in)
1 Bottom plate 19 (0.75)
2 Side plate 12 (0.47)
3 Front plate (center) 16 (0.63)
4 Front plate (side) 12 (0.47)
5 Canopy top plate 9 (0.35)
6 Canopy top plate (front) 6 (0.24)
7 Corner (bottom-side) 12 (0.47)
8 Corner (bottom-front) 12 (0.47)
9 Canopy corner (center) 16 (0.63)
10 Canopy corner (side) 12 (0.47)
Liner weight kg (lb) 5950 (13,120)
4A-45
AH_25.book Page 46 Tuesday, March 23, 2004 9:41 AM
Plate thickness
No. Part
mm (in)
1 Bottom plate 14 (0.55)
2 Side plate —
3 Front plate (center) —
4 Front plate (side) —
5 Canopy top plate —
6 Corner (bottom-side) —
7 Corner (bottom-front) —
8 Canopy corner (center) —
9 Canopy corner (side) —
Liner weight kg (lb) 995 (2,190)
4A-46
AH_25.book Page 47 Tuesday, March 23, 2004 9:41 AM
4A-47
AH_25.book Page 48 Tuesday, March 23, 2004 9:41 AM
4A-48
AH_25.book Page 49 Tuesday, March 23, 2004 9:41 AM
HD985-5
Extension Item HD785-5 64 m3 70 m3
(83.7 cuyd) (91.6 cuyd)
Body capacity m3 40.0/60.0 45.0/64.0 48.0/70.0
Without body Struck/heaped (yd3) (52.3/78.5) (58.9/83.7) (62.8/91.6)
extension Loading height 4285 4545 4565
mm (ft.in) (14'1") (14'11") (15')
Body capacity m3
— — —
200 mm Struck/heaped (yd3)
(7.9 in) Loading height
— — —
mm (ft.in)
Body capacity m3
— — —
250 mm Struck/heaped (yd3)
(9.8 in) Loading height
— — —
mm (ft.in)
Body capacity m3
— — —
300 mm Struck/heaped (yd3)
(11.8 in) Loading height
— — —
mm (ft.in)
30.00-R51 30.00-R51
Installed tire size 27.00-R49
(E3) (E4)
Remarks *:Standard equipment for HD465-7 rock body
4A-49
AH_25.book Page 50 Tuesday, March 23, 2004 9:41 AM
HD325-6
Specific gravity (Loose condition)
Body capacity
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 US ton/m3
m3 (ys3)
0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 ton/m3
HD465-7
Specific gravity (Loose condition)
Body capacity
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 US ton/m3
m3 (ys3)
0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 ton/m3
HD785-6
Specific gravity (Loose condition)
Body capacity
1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 US ton/m3
m3 (ys3)
0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 ton/m3
FVBH0269
4A-50
AH_25.book Page 51 Tuesday, March 23, 2004 9:41 AM
Canopy spill
guard
FVBH0035
HD985-5
Spill guard height Item HD605-7 HD785-5 64 m3 70 m3
(83.7 cu.yd) (91.6 cu.yd)
Mounting method
Weld-on — — —
150 mm (5.9 in)
Overall height
4400 (14'5") — — —
mm (ft.in)
**Weld-on **Weld-on **Weld-on
Mounting method —
(STD) (STD)
200 mm (7.9 in)
Overall height —
5050 5120 5140
mm (ft.in) (16'7") (16'10") (16'10")
Mounting method
*Weld-on *Weld-on *Weld-on *Weld-on
300 mm (11.8 in)
Overall height
4550 (14'11") 5150 (16'11") 5220 (17'2") 5240 (17'2")
mm (ft.in)
Installed tire size 24.00R35 27.00-R49 30.00-R51(E3) 30.00-R51(E4)
Remarks *:When installing optional spill guard, remove standard or other spill guard.
*:200 mm (7.9 in) spill guard is standard equipment.
4A-51
AH_25.book Page 52 Tuesday, March 23, 2004 9:41 AM
FVBH0257
4A-52
AH_25.book Page 53 Tuesday, March 23, 2004 9:41 AM
Production OFF-HIGHWAY
DUMP TRUCKS
TRAVEL TIME (One way)
UNIT: MIN.
AVERAGE TRAVEL SPEED KM/HR (MPH)
DISTANCE ONE WAY
5 10 15 20 25 30 35 40 45 50 55 60
METERS FEET (3.1) (6.2) (9.3) (12.4) (15.5) (18.6) (21.7) (24.9) (28.0) (31.1) (34.2) (37.3)
50 160 0.60 0.30 0.20 0.15 0.12 0.10 0.09 0.88 0.07 0.06 0.05 0.05
100 330 1.20 0.60 0.40 0.30 0.24 0.20 0.17 0.15 0.13 0.12 0.11 0.10
200 660 2.40 1.20 0.80 0.60 0.48 0.40 0.34 0.30 0.27 0.24 0.22 0.20
300 980 3.60 1.80 1.20 0.90 0.72 0.60 0.51 0.45 0.40 0.36 0.33 0.30
500 1640 6.00 3.00 2.00 1.50 1.20 1.00 0.86 0.75 0.67 0.60 0.55 0.50
1000 3280 12.00 6.00 4.00 3.00 2.40 2.00 1.71 1.50 1.33 1.20 1.09 1.00
1500 4920 18.00 9.00 6.00 4.50 3.60 3.00 2.57 2.25 2.00 1.80 1.64 1.50
2000 6560 24.00 12.00 8.00 6.00 4.80 4.00 3.43 3.00 2.67 2.40 2.18 2.00
3000 9840 36.00 18.00 12.00 9.00 7.20 6.00 5.14 4.50 4.00 3.60 3.27 3.00
5000 16410 60.00 30.00 20.00 15.00 12.00 10.00 8.57 7.50 6.67 6.00 5.45 5.00
Cycle time = Loading time + Hauling time +Dumping time + Return time + Spot & delay time
Determine hauling and return time from the above table respectively.
Loading time = (Loader cycle time) × (No. of cycles to fill dump truck)
Average fixed time (dumping, spot & delay): 1.25 ~ 1.65 min.
4A-53
AH_25.book Page 54 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 4B
ARTICULATED
DUMP TRUCKS
CONTENTS
Features .................................................................... 4B-2
Specifications ........................................................... 4B-4
Dimensions ............................................................... 4B-5
Use of performance curve ....................................... 4B-6
Performance curve
HM300-1 ................................................................ 4B-7
HM350-1 ................................................................ 4B-8
HM400-1 ................................................................ 4B-9
Ground pressure .................................................... 4B-10
Tire Selection .......................................................... 4B-12
4B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features ARTICULATED
DUMP TRUCKS
Rear frame
Front frame
4B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Features ARTICULATED
DUMP TRUCKS
High productivity • Komatsu Designed Electronically
Controlled Transmission
• High performance SAA6D125E-3 and Komatsu designed Electronically Controlled
SAA6D140E-3 Komatsu engines transmission called K-ATOMiCS has been
• Those engine delivers faster acceleration and successfully employed in Komatsu’s rigid dump
higher travel speeds with the highest trucks. The electronic clutch modulation system
horsepower per ton in its class. ensures proper clutch pressure when the clutch is
• The engines meets the USA EPA Tier 2 engaged. the total control system controls both
emission regulations. the engine and transmission by monitoring the
vehicle conditions. This high technology system
• High torque at low speed, impressive assures smooth shifts without shock.
acceleration and low fuel consumption ensure
maximum productivity. • Hydropneumatic Suspension
• Interaxle & Differential Locking Systems The hydropneumatic suspension has been
proven on Komatsu’s rigid dump trucks. The front
The full-time six-wheel drive system reduces axle suspension employs “De Dion” type design,
slippage. A wet multiple-disc interaxle clutch also allowing the machine to ride more smoothly over
locks the three axles in unison for greater traction. bumps. The rear-axles are mounted on a
The interaxle lock and differential locks can be dynamic equalizer structure equipped with
switched on and off while the truck is traveling, hydropneumatic suspension.
thereby boosting productivity.
• Large Capacity Body and Box Section • Fully Hydraulically Controlled Wet
Frame Structure Multiple-Disk Brakes and Retarder
The body is built of thick wear-resistant steel with Wet multiple-disk brakes have been proven on
a Brinell hardness of 400, and the body shape Komatsu dump trucks and wheel loaders. They
provides excellent load stability. ensure highly reliable and stable brake
performance. The large-capacity wet-multiple
• Articulated Steering disk brakes also function as a highly responsive
Fully hydraulic articulated steering offers low- retarder which gives the operator great
effort operating performance and maneuverability. confidence while traveling downhill.
Small minimum turning radius provides the
freedom to move about in confined areas.
4B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Specifications ARTICULATED
DUMP TRUCKS
Model
Item HM300-1 HM350-1 HM400-1
WEIGHT: kg (lb)
Empty vehicle weight* 22500 (49,600) 28550 (62,940) 30300 (66,800)
Distribution (front) 12770 (28,150) 15850 (34,920) 16790 (37020)
(center) 5000 (11,020) 6350 (14,000) 6755 (14,890)
(rear) 4730 (10,430) 6350 (14,000) 6755 (14,890)
Gross vehicle weight 49875 (109,950) 60925 (134,320) 66875 (147,430)
Distribution (front) 14860 (10710) 18545 (40,880) 19055 (42,010)
(center) 17805 (39,250) 21190 (46,720) 23910 (51,120)
(rear) 17210 (37,940) 21190 (46,720) 23910 (51,120)
Gross horsepower HP (kW)/RPM 335 (250)/2000 399 (298)/2000 444 (331)/2000
Flywheel horsepower HP (kW)/RPM 324 (242)/2000 389 (290)/2000 430 (321)/2000
HAULING CAPACITY:
Maximum payload m. ton (U.S. ton) 27.3 (30.1) 32.3 (35.6) 36.5 (40)
Heaped capacity (2:1) m3 (yd3) 16.6 (21.7) 19.8 (25.9) 22.3 (29.2)
PERFORMANCE:
Maximum speed km/h (MPH) 59.0 (36.7) 57.0 (35.4) 58.6 (36.4)
Turning radius m (ft.in) 7.96 (26'1") 8.4 (27'7") 8.7 (28'7")
ENGINE: KOMATSU KOMATSU KOMATSU
Model SAA6D125E SAA6D140E SAA6D140E
No. of cylinders- 6-125 × 150 6-140 × 165 6-140 × 165
bore × stroke mm (in) (4.92 × 5.91) (5.51 × 6.50) (5.51 × 6.50)
Displacement ltr. (in3) 11.04 (674) 15.24 (930) 15.24 (930)
DIMENSION: See DIMENSIONS
CAPACITY:Fuel tank ltr. (U.S. Gal) 382 (100.9) 495 (130.8) 495 (130.8)
* Weight includes lubricants, coolant, full fuel tank and standard body.
4B-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Dimensions ARTICULATED
DUMP TRUCKS
R
T
J K
N
Q
B
M
H P
D E F G
C A
FVBH0162
Unit: mm (ft.in)
HM300-1 HM350-1 HM400-1
Tires 23.5 R25 26.5 R25 29.5 R25
A 10095 (33'1") 10730 (35'2") 11025 (36'2")
B 3500 (11'6") 3595 (11'10") 3700 (12'2")
C 2900 (9'6") 3250 (10'8") 3450 (11'4")
D 2280 (7'6") 2590 (8'6") 2690 (8'10")
E 4100 (13'5") 4350 (14'3") 4350 (14'3")
F 1710 (5'7") 1850 (6'1") 1970 (6'6")
G 1695 (5'7") 1645 (5'5") 1820 (6'0")
H 510 (1'8") 585 (1'11") 620 (2'0")
J 1600 (5'3") 1600 (5'3") 1600 (5'3")
K 4965 (16'3") 5250 (17'3") 5400 (17'9")
M 2790 (9'2") 2840 (9'4") 2970 (9'9")
N 6445 (21'2") 7035 (23'1") 7130 (23'5")
P 605 (2'0") 720 (2'4") 720 (2'4")
Q (deg.) 70° 70° 70°
R (deg.) 45° 45° 45°
S 7960 (26'1") 8400 (27'7") 8700 (28'7")
T 4010 (13'2") 4060 (13'4") 4170 (13'8")
4B-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
US ton ton
50
50 GROSS WEIGHT
40 25 30 40 50 60 70 80 90 100 US ton
40
20 30 40 50 60(A)70 80 90 ton
30 F1
30 EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
35.0
20 30.0
20 25.0
(E) (C)
F2 20.0 (B)
10 15.0
14.0
10 9 13.0
9 8 F3 12.0
11.0
8 7
RIMPULL
10.0
7 6 9.0
6 8.0
5 F4 7.0
5
4 6.0
4 5.0
3 F5
3 4.0
2 F6 3.0
2
2.0
1
1
0 0
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
(D)
TRAVEL SPEED
4B-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
HM300-1 ARTICULATED
Performance Curve DUMP TRUCKS
Travel Performance Curve
US ton ton
50
50 GROSS WEIGHT
40 25 30 40 50 60 70 80 90 100 US ton
40
20 30 40 50 60 70 80 90 ton
30
30 EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
F1 45.0
40.0
20
20 35.0
30.0
25.0
10 20.0
9 F2
10
9 8 15.0
7 14.0
8
RIMPULL
13.0
7 6 F3 12.0
11.0
6 5 10.0
9.0
5 8.0
4 F4
4 7.0
6.0
3
3 F5
5.0
4.0
2
2 F6
3.0
2.0
1
1
0 0
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
Brake performance
WITH EXHAUST(OPTION)
-35
-30
F1
-25
-20
F2
-15
F3
-10
F4
F5 -5
F6
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
TRAVEL SPEED
FVBH0165
4B-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
HM350-1 ARTICULATED
Performance Curve DUMP TRUCKS
Travel Performance Curve
US ton ton
50
50 GROSS WEIGHT
40 25 30 40 50 60 70 80 90 100 US ton
40
20 30 40 50 60 70 80 90 ton
30 F1
30 EMPTY LOADED
40.0
TOTAL RESISTANCE (GRADE+ROLLING)(%)
35.0
20 30.0
20
25.0
F2 20.0
10 15.0
10 9 14.0
9 8 F3 13.0
12.0
8 7
RIMPULL
11.0
7 10.0
6
9.0
6 5 8.0
5 F4
7.0
4
6.0
4
5.0
3 F5
3 4.0
2 F6
3.0
2
2.0
1
1
0 0
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
Brake performance
WITH EXHAUST(OPTION)
-35
F1
-30
-25
F2
-20
F3 -15
F4 -10
F5
F6 -5
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
TRAVEL SPEED
FVBH0167
4B-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
HM400-1 ARTICULATED
Performance Curves DUMP TRUCKS
Travel Performance Curve
US ton ton
50
50 GROSS WEIGHT
40 25 30 40 50 60 70 80 90 100 US ton
40
20 30 40 50 60 70 80 90 ton
30 F1
30 EMPTY LOADED
TOTAL RESISTANCE (GRADE+ROLLING)(%)
35.0
20 30.0
20 25.0
F2 20.0
10 15.0
14.0
10 9 13.0
9 8 F3 12.0
11.0
8 7
RIMPULL
10.0
7 6 9.0
6 8.0
5 F4 7.0
5
4 6.0
4 5.0
3 F5
3 4.0
2 F6 3.0
2
2.0
1
1
0 0
0 10 20 30 40 50 60 70 km/h
0 10 15 20 25 30 35 40 MPH
TRAVEL SPEED
Brake performance
GRADE DISTANCE : COUNTINUOUS DESENT
0 10 20 30 40 50 60 70 80 90 100 110 US ton
0 10 20 30 40 50 60 70 80 90 100 ton
EMPTY LOADED -50 -45
-40
WITHOUT EXHAUST
TOTAL RESISTANCE (GRADE + ROLLING) (%)
WITH EXHAUST(OPTION)
-35
F1
-30
-25
F1
F2 -20
F2 -15
F3
F3
-10
F4
F4 F5
F5 -5
F6
F6
0 10 20 30 40 50 60 70 80 90 100 km/h
0 10 20 30 40 50 60 MPH
TRAVEL SPEED
FVBH0169
4B-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
HM350-1
Tire
Item 26.5R25 800/65R29
WEIGHT: kg (lb)
Empty vehicle weight* 28550 (62,940) 30034 (66,210)
Distribution (front) 15850 (34,920) 16378 (36,110)
(center) 6350 (14,000) 6828 (15,050)
(rear) 6350 (14,000) 6828 (15,050)
Gross vehicle weight 60925 (134,320) 62409 (137,590)
Distribution (front) 18545 (40,880) 18973 (41,830)
(center) 21190 (46,720) 21718 (47,880)
(rear) 21190 (46,720) 21718 (47,880)
GROUND CONTACT AREA: cm2 (in2)
Empty: Front tire 2400 (372.0) 2662 (412.6)
Center tire 1160 (179.8) 1707 (264.6)
Rear tire 1160 (179.8) 1707 (264.6)
Loaded: Front tire 2700 (418.5) 2932 (454.5)
Center tire 2650 (410.8) 3170 (491.4)
Rear tire 2650 (410.8) 3170 (491.4)
GROUND PRESSURE: kg/cm2 (PSI/kPa)
Empty: Front tire 3.30 (46.9/323.6) 3.08 (43.8/302.0)
Center tire 2.74 (39.0/268.7) 2.00 (28.4/196.1)
Rear tire 2.74 (39.0/268.7) 2.00 (28.4/196.1)
Loaded: Front tire 3.43 (48.8/336.4) 3.24 (46.1/317.8)
Center tire 4.00 (56.9/392.3) 3.43 (48.8/336.4)
Rear tire 4.00 (56.9/392.3) 3.43 (48.8/336.4)
* Weight includes lubricants, coolant, full fuel tank and standard body.
4B-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
4B-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
HM350-1
Manu- Charac- Star Inflation
Tire size Pattern Code Applicable terrain Feature
facturer* teristics Rating pressure
26.5 R25 BS VKT CR E2 ✩✩ 4.5 Soft and muddy surfaces Good traction and floatation
Rubber volume of tread ratio
(VKT:1, VLT:1.25)
26.5 R25 BS VLT CR E2 ✩✩ 4.5 Soft and muddy surfaces
Exellent maneuverability,
traction and floatation
High wear-resistance, cut-
26.5 R25 BS VLTS CR E4 ✩✩ 4.5 Soft and muddy surfaces resistance because of deep
tread (STD:1, VLTS:1.5)
26.5 R25 GY RL-2+ E2 ✩✩ 4.5
26.5 R25 GY GP-2B E2 ✩✩
26.5 R25 GY TL-3A+ E3 ✩✩
26.5 R25 GY GP-4B AT E4 ✩✩
26.5 R25 MC XADN E3T E3
26.5 R25 MC XADT E4T E4 4.5
26.5 R25 MC XADN E3V E3 4.5
Soft surface and under Good traction, anti-sideways slip
26.5 R25 TY T-351 E3 ✩✩
ground and cut-resistance
800/65 R29 GY GP-4D E4 ✩✩ 4.0
HM400-1
Manu- Charac- Star Inflation
Tire size Pattern Code Applicable terrain Feature
facturer* teristics Rating pressure
High wear-resistance, cut-
29.5 R25 BS VLTS CR E4 ✩✩ Soft and muddy surfaces
resistance
29.5 R25 BS VKT CR E2 ✩✩ 3.8 Soft and muddy surfaces Good traction and floatation
29.5 R25 BS VLT E2 ✩✩ 3.8 Soft and muddy surfaces Good traction and floatation
29.5 R25 BS VKT E2 ✩✩ 3.8 Soft and muddy surfaces Good traction and floatation
29.5 R25 GY RL-2+ E2 ✩✩ 4.1
29.5 R25 GY GP-2B E2 ✩✩
29.5 R25 GY GP-4B AT E4 ✩✩
29.5 R25 MC XADN E3T E3
29.5 R25 MC XADN E3V E3
29.5 R25 MC XADT E4T E4 4.0
Soft surface and under Good traction, anti-sideways slip
29.5 R25 TY T-351 E3 ✩✩
ground and cut-resistance
875/65 R29 GY GP-4D E4 ✩✩ 4.5
875/65 R29 MC XAD65-1 E3 4.5
* Tire maker.........BS:BRIDGESTONE GY:GOODYEAR MC:MICHELIN TY:TOYO
4B-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
TIRE PATTERN
BRIDGESTONE
GOODYEAR
MICHELIN
TOYO
4B-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 4C
CRAWLER CARRIERS
CONTENTS
Features .................................................................... 4C-2
specifications ........................................................... 4C-3
Dimensions ............................................................... 4C-4
4C-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
4C-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
Item CD60R-1 CD110R-2
WEIGHT: kg (lb)
Net weight - Unloaded 8500(18,740) 15600 (34,390)
Gross weight - Loaded 14580(32,150) 26600 (58,640)
FLYWHEEL HORSEPOWER HP (kW)/RPM 133(99.3)/2000 244 (182)/1900
HAULING CAPACITY:
Max. payload kg (lb) 6000 (13,230) 11000 (24,250)
Heaped capacity m3 (cu.yd) 3.2 (4.2) 6.1 (8.0)
PERFORMANCE:
Travel speed Low km/h (MPH) 6.0 (3.7) 4.5 (2.8)
High km/h (MPH) 8.5 (5.3) 10.0 (6.2)
Swing radius of upper structure mm (ft.in) 2695 (8'10") 3170 (10'5")
DIMENSION: mm (ft.in)
Overall length 4825(15'10") 5405 (17'9")
Overall width 2640 (8'8") 3330 (10'11")
Overall height (at transport) 2775 (9'1") 3185 (10'5")
Track gauge 1790 (5'10") 2080 (6'10")
Track length, between tumblers 3190 (10'6") 3850 (12'8")
ENGINE: KOMATSU KOMATSU
Model S6D102E-1 SAA6D114E-2
No. of cylinders- mm (in) 6-102 × 120 6-114 × 135
bore × stroke (4.02 × 4.72) (4.49 × 5.31)
Piston displacement Itr. (cu.in) 5.88 (3.59) 8.27 (505)
UNDERCARRIAGE:
No. of rollers (carrier/track) 2/8 2/8
Track shoes Steel reinforced rubber shoe Steel reinforced rubber shoe
Width of shoe, standard mm (in) 600 (23.6) 800 (31.5)
CAPACITY (Refilled):
Fuel tank ltr. (U.S. Gal) 130 (34.3) 300 (79.3)
4C-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
CD60R-1
140
2220
2095
110 2695
2550
2230 2455
4685
2640
2450 110 2725
4360
400
58˚
2775
1855
1455
2515
920
930
500
G.L
600 3190
1790 3840 645
2390
CD110R-2
275 11" 28
65
9'
5"
Transportation 3050 10'
10'5"
2680 8'10"
3170
3290 10'10"
Transportation 3185 10'5"
˚
60
535 1'9"
2205 7'3"
1895 6'3"
1670 5'6"
1060 3'6"
685 2'3"
FVHM0489
4C-4
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 4D
SLAG DUMP TRUCKS
CONTENTS
Features specifications ........................................... 4D-2
4D-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
• The slag dump trucks are based on the off-highway dump trucks.
Main components such as engines, power trains and frames are commonly used on construction
machinery and are of proven strength, thus providing superior durability, reliability and parts supply.
• All work equipment can be operated from the cab.
In addition, outrigger and pot pins are also operable from outside the cab thus ensuring greater safety.
• Pot loading / unloading has been simplified on self-loading specification trucks, by the use of hooks which
have been mounted on the arm.
• The arm, table and cab have been designed taking the heat factor into full consideration for safe
operation.
• Comfortable cab, superior front visibility and ball-screw steering enable smooth, light operation for
superior operability.
• The installation of large-size tires, adoption of sintered alloy for the clutch lining and changed spring have
led to an increased torque capacity ratio among other improvements.
Therefore trucks have more than enough durability for heavy-duty operations.
Specifications
Model
Item HS100S-11 HS150S-11 HS600S-3
WEIGHT: kg (lb)
Empty vehicle weight 25000 (55,120) 39000 (85,980) 46000 (101,410)
Distributed weight
(front) 12000 (26,460) 12500 (27,560) 14500 (31,970)
(rear) 13000 (28,660) 13250 (29,210) 15750 (34,720)
(idle) — 13250 (29,210) 15750 (34,720)
Gross vehicle weight 50000 (110,230) 84000 (185,190) 106000 (233,690)
Distributed gross weight
(front) 13800 (30,420) 13800 (30,420) 20000 (44,100)
(rear) 36200 (79,810) 35100 (77,380) 43000 (94,800)
(idle) — 35100 (77,380) 43000 (94,800)
Flywheel horsepower HP (kW)/RPM 315 (235)/2100 315 (235)/2100 315 (235)/2100
HAULING CAPACITY:
Maximum load kg (US ton) 25000 (27.6) 45000 (49.6) 60000 (66)
Pot capacity m3 (yd3) 4~6 (5.2~7.8) 6~10 (7.8~13.1) 10~15 (13.1~19.6)
PERFORMANCE:
Maximum speed km/h (MPH) 40 (24.9) 40 (24.9) 40 (24.9)
Turning radius m (ft.in) 7.5 (24'7") 9.5 (31'2") 9.5 (31'2")
ENGINE: KOMATSU KOMATSU KOMATSU
Model SA6D125E SA6D125E SA6D125E
No. of cylinders- mm (in) 6-125 × 1 50 6-125 × 1 50 6-125 × 1 50
bore × stroke (4.9" × 5.9") (4.9" × 5.9") (4.9" × 5.9")
Displacement Itr. (in3) 11.05 (674) 11.05 (674) 11.05 (674)
DIMENSION: mm (ft.in)
Overall length 7200(23'7") 8500 (28'1") 8700 (28'6")
Overall width 4150 (13'7") 4700 (15'5") 5200 (17'1")
Overall height 3700 (12'2") 4500 (15') 4500 (16'1")
Ground clearance 300 (1') 330 (1'1") 330 (1'1")
Wheelbase,first/secondary 3600 (11'10") 3600 (11'10") 3600 (11'10")
secondary/third — 1700 (5'7") 1700 (5'7")
Tread (front) 2700 (8'10") 2700 (8'10") 2700 (8'10")
(rear) 2180 (7'2") 2180 (7'2") 2180 (7'2")
(idle) — 2180 (7'2") 2180 (7'2")
TIRES: Front tire 14.00-25-24PR × 2 14.00-25-24PR × 2 16.00-25-24PR × 2
Rear tire 14.00-25-24PR × 4 16.00-25-24PR × 4 16.00-25-24PR × 4
*Idle tire — 14.00-25-24PR × 4 14.00-25-24PR × 4
CAPACITY: Fuel tank ltr. (U.S. Gal) 380 (100) 380 (100) 380 (100)
NOTE: 1. Work equipment for hanging the pot is designed by matching it to the retained pot.
2. Dimensions of vehicle is changed by the pot shape and the loading method.
3. The above specifications are subject to change without notice.
4D-2
CONTENTS
SECTION 5
INDEX
SECTION 5A
MOTOR GRADERS
CONTENTS
Features .................................................................... 5A-2
Specifications ........................................................... 5A-4
Dimensions ............................................................... 5A-6
Attachment Availability ............................................ 5A-8
Scarifier Specifications ........................................... 5A-9
Front Dozer Blade Specifications ......................... 5A-12
Rear Mounted Ripper Specifications ................... 5A-13
Upper Attachments ................................................ 5A-14
Tire Availability and TMPH .................................... 5A-15
Attachments and Options ..................................... 5A-16
5A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
5A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Max. uptime
• Non-spin differential
Non-spin differential with automatic locking and
unlocking can be installed as an option on the
final drives, assuring the optimum in smooth
steering.
5A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Model
GD510R-1 GD511A-1 GD555-3A GD555-3C*6
Item
OPERATING WEIGHT* kg (lb) 10700 (23,590) 10800 (23,810) 13100 (28,880) 14040 (30,950)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 125 (93)/2500 135 (101)/2900 160 (119)/2000 160 (119)/2000
PERFORMANCE:
Travel speeds: km/h (MPH) Low/ High
Forward 1st 3.9 (2.4)/8.6 (5.3) 3.4 (2.1) 3.3 (2.1) 3.3 (2.1)
2nd 7.0 (4.3)/15.5 (9.6) 6.1 (3.8) 4.8 (3.0) 4.8 (3.0)
3rd 12.5 (7.8)/27.5 (17.1) 10.7 (6.6) 6.8 (4.2) 6.8 (4.2)
4th 19.5 (12.1)/42.9 (26.7) 14.1 (8.8) 9.8 (6.1) 9.8 (6.1)
5th — 25.5 (15.8) 14.9 (9.3) 14.9 (9.3)
6th — 44.5 (27.7) 21.6 (13.4) 21.6 (13.4)
7th — — 29.6 (18.4) 29.6 (18.4)
8th — — 42.9 (26.7) 42.9 (26.4)
Reverse (Max.) 26.6 (16.5) 54.4 (33.8) 39.1 (24.3) 39.1 (24.3)
Max. traction (Drawbar pull) kg (lb) 6080 (13,400) 6140 (13,535) 7490 (16,510) 8030 (17,700)
Min. turning radius** mm (ft.in) 10400 (34'1") 6600 (21'8") 6800 (22'4") 6800 (22'4")
DIMENSIONS:
Treads: Front mm (ft.in) 2020 (6'8") 2020 (6'8") 2130 (7'0") 2130 (7'0")
Rear mm (ft.in) 2020 (6'8") 2020 (6'8") 2130 (7'0") 2130 (7'0")
Articulation angle (each) degree — 27 23 23
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
S6D95L S6D95L SAA6D102E SAA6D102E
No. of cylinders- mm (in) 6-95 × 115 6-95 × 115 6 –102 × 120 6 –102 × 120
bore × stroke (3.74 × 4.53) (3.74 × 4.53) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (in3) 4.89 (298) 4.89 (298) 5.88 (359) 5.88 (359)
CAPACITY
Fuel tank ltr. (U.S. Gal) 227 (60.0) 227 (60.0) 340 (90) 340 (90)
Model
GD611A-1 GD655-3A GD655-3C*6 GD661A-1
Item
OPERATING WEIGHT* kg (lb) 12500 (27,555) 14070 (31,020) 15000 (33,070) 13300 (29,320)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 155 (116)/2500 190 (142)/1990 190 (142)/1900 180 (134)/2500
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 3.5 (2.2) 3.3 (2.1) 3.3 (2.1) 3.5 (2.2)
2nd 6.3 (3.9) 4.7 (2.9) 4.7 (2.9) 6.3 (3.9)
3rd 10.8 (6.7) 6.7 (4.2) 6.7 (4.2) 10.8 (6.7)
4th 14.8 (9.2) 9.7 (6.0) 9.7 (6.0) 14.8 (9.2)
5th 26.2 (16.3) 14.6 (9.1) 14.6 (9.1) 26.2 (16.3)
6th 44.6 (27.7) 21.2 (13.2) 21.2 (13.2) 44.6 (27.7)
7th — 29.1 (18.1) 29.1 (18.1)
8th — 42.2 (26.2) 42.2 (26.2)
Reverse (Max.) 54.4(33.8) 38.4 (23.9) 38.4 (23.9) 54.4 (33.8)
Max. traction (Drawbar pull) kg (lb) 7100 (15,650) 8050 (17,750) 8580 (18,920) 7400 (16,315)
Min. turning radius** mm (ft.in) 6900 (22'8") 6900 (22'8") 6900 (22'8") 6900 (22'8")
DIMENSIONS:
Treads: Front mm (ft.in) 2020 (6'8") 2130 (7'0") 2130 (7'0") 2020 (6'8")
Rear mm (ft.in) 2020 (6'8") 2130 (7'0") 2130 (7'0") 2020 (6'8")
Articulation angle(each) degree 26 23 23 26
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
S6D105 SAA6D114E SAA6D114E S6D105
No. of cylinders- mm (in) 6 –105 × 120 6 –114 × 135 6 –114 × 135 6 –105 × 125
bore × stroke (4.13 × 4.92) (4.49 × 5.32) (4.49 × 5.32) (4.13 × 4.92)
Piston displacement ltr. (in3) 6.49 (396) 8.27 (505) 8.27 (505) 6.49 (396)
CAPACITY
Fuel tank ltr. (U.S. Gal) 285 (75.3) 340 (90) 340 (90) 285 (75.3)
* Operating weight includes standard blade, standard tires, full fuel tank, lubricants, operator and standard equipment.
** At center of front outside tire, combining the use of full articulation, full front wheel steering and leaning.
*6 USA version
5A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Model
GD675-3A GD675-3C*6 GD705A-4 GD825A-2
Item
OPERATING WEIGHT* kg (lb) 14870 (32,780) 15810 (34,850) 17620 (38,580) 26350 (58,090)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 200 (149)/1900 200 (149)/1900 200 (149)/2000 280 (209)/2100
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward 1st 3.3 (2.1) 3.3 (2.1) 3.9 (2.4) 4.0 (2.5)
2nd 4.7 (2.9) 4.7 (2.9) 5.2 (3.2) 5.4 (3.4)
3rd 6.7 (4.2) 6.7 (4.2) 7.6 (4.7) 8.0 (5.0)
4th 9.7 (6.0) 9.7 (6.0) 11.5 (7.1) 11.5 (7.1)
5th 14.6 (9.1) 14.6 (9.1) 15.0 (6.8) 15.8 (9.8)
6th 21.2 (13.2) 21.2 (13.2) 20.5 (12.7) 21.4 (13.3)
7th 29.1 (18.1) 29.1 (18.1) 30.0 (18.6) 31.3 (19.4)
8th 42.2 (26.2) 42.2 (26.2) 43.0 (26.7) 44.9 (27.9)
Reverse (Max.) 38.3 (23.8) 38.3 (23.8) 45.9 (28.5) 47.9 (29.8)
Max .traction (Drawbar pull) Kg (lb) 8510 (18,760) 9050 (19,950) 10180 (22,420) 14705 (32,420)
Min. turning radius** mm (ft.in) 6900 (22'8") 6900 (22'8") 7500 (24'7") 7900 (25'11")*5
DIMENSIONS:
Treads: Front mm (ft.in) 2130 (7'0") 2130 (7'0") 2300 (7'7") 2620 (8'7")
Rear mm (ft.in) 2130 (7'0") 2130 (7'0") 2300 (7'7") 2620 (8'7")
Articulation angle (each) degree 23 23 26 25
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
SAA6D114E SAA6D114E S6D125 S6D140E
No. of cylinders- mm (in) 6 –114 × 135 6 –114 × 135 6 –125 × 150 6-140 × 165
bore × stroke (4.49 × 5.31) (4.49 × 5.31) (4.9 × 5.9) (5.51 × 6.50)
Piston displacement ltr. (in3) 8.27 (505) 8.27 (505) 11.05 (674) 15.24 (930)
CAPACITY
Fuel tank ltr. (U.S. Gal) 340 (90) 340 (90) 400 (105.7) 500 (132.1)
* Operating weight includes standard blade, standard tires, full fuel tank, lubricants, operator and standard equipment.
** At center of front outside tire, combining the use of full articulation, full front wheel steering and leaning.
*5 With differential
*6 USA version
5A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
E F
A
G.L
B D
C
See Specifications
5A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
E F
A
G.L
B D
C
See Specifications
5A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
:Standard equipment
:Optional equipment
Model GD GD GD GD GD GD GD GD GD
Item 510R-1 511A-1 555-3A 611A-1 655-3A 661A-1 675-3A 705A-4 825A-2
BLADE
2.2 m (7.2 ft)
2.5 m (8.2 ft)
2.8 m (9.2 ft)
3.05 m (10 ft)
3.1 m (10.2 ft)
3.4 m (11.2 ft)
3.7 m (12.1 ft)
4.0 m (13.1 ft)
4.3 m (14.1 ft)
4.9 m (16.1 ft)
VARIABLE BLADE
HYDRAULIC BLADE TIP
CONTROL
EXTENSION BLADE
FRONT DOZER BLADE
SCARIFIER
5 teeth
6 teeth
7 teeth
9 teeth
11 teeth
REPLACEBLE TIP
TEETH FOR SCARIFIER
REAR MOUNT RIPPER
PUSH PLATE
5A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Model
500 SERIES *3
Item
NO. OF TEETH 9
ADDITIONAL WEIGHT: kg (lb) Standard Teeth Point Teeth
To operating weight +660 (+1,460) +665 (+1,470)
[+685 (+1,510)] [+690 (+1,520)]
To front axle +565 (+1,250) +570 (+1,260)
[+585 (+1,290)] [+590 (+1,300)]
To rear axle +95 (+210) +95 (+210)
[+100 (+220)] [+100 (+220)]
DIMENSIONS:
A: Distance between teeth mm (ft.in) 970 (3'2") 850 (2'9")
and center of front tire
SCARIFIER LOAD* kg (lb) 4440 (9,790) 4335 (9,560)
SCARIFIER RANGE:
Digging angle degree 61 ~ 74 51 ~ 64
Max. lift above ground mm (ft.in) 340 (1'1") [530 (1'9")] 320 (1'1") [495 (1'7")]
Max. digging depth mm (ft.in) 260 (10.2") [290 (11.4")] 260 (10.2") [290 (11.4")]
SCARIFIER EQUIPMENT:
Type V-type, 2-stage adjustable V-type, 2-stage adjustable
Weight kg (lb) 660 (1,460) 665 (1,470)
B: Digging width mm (ft.in) 1065 (3'6") 1090 (3'7")
Tooth:
As-installed mm (in) 275 × 77 × 25 185 × 50 × 36.3
Height × width × thickness (10.8 × 3.0 × 1.0) (7.3 × 2.0 × 1 .4)
APPLICABLE MODEL GD510R*3 GD510R*3
GD511A*3 GD511A*3
Model
500 SERIES
Item
NO.OF TEETH 11
ADDITIONAL WEIGHT: kg (lb) Standard Teeth Point Teeth
To operating weight +690 (+1,520) +565 (+1250) +695 (+1,530) +570 (+1260)
[+715 (+1,580)] [+575 (+1270)] [+720 (+1,590)] [+585 (+1290)]
To front axle +590 (+1,300) +470 (+1040) +595 (+1,310) +475 (+1050)
[+610 (+1,340)] [+475 (+1050)] [+615 (+1,360)] [+485 (+1070)]
To rear axle +100 (+220) +95 (+210) +100 (+220) +95 (+210)
[+105 (+230)] [+100 (+220)] [+105 (+230)] [+100 (+220)]
DIMENSIONS:
A: Distance between teeth mm (ft.in) 970 (3'2") 1005 (3'4") 850 (2'9") 960 (3'2")
and center of front tire
SCARIFIER LOAD* kg (lb) 4470 (9,850) 5335 (11,760) 4265 (9,400) 5295 (11,670)
SCARIFIER RANGE:
Digging angle degree 61 ~ 74 63 ~ 78 51 ~ 64 53 ~ 69
Max. lift above ground mm (ft.in) 340 (1'1") 350 (1'2") 320 (1'1") 320 (1'1")
[530 (1'9")] [495 (1'7")]
Max. digging depth mm (ft.in) 260 (10.2") 255 (10") 260 (10.2") 265 (10.4")
[290 (11.4")] [365 (1'2")] [290 (11.4")] [365 (1'2")]
SCARIFIER EQUIPMENT:
Type V-type, 2-stage adjustable V-type, 2-stage adjustable
Weight kg (lb) 690 (1,520) 565 (1250) 695 (1,530) 570 (1260)
B: Digging width mm (ft.in) 1325 (4'4") 1405 (4'7") 1350 (4'5") 1430 (4'8")
Tooth:
As-installed mm (in) 275 × 77 × 25 185 × 50 × 36.3
Height × width × thickness (10.8" × 3.0" × 1.0") (7.3" × 2.0" × 1.4")
GD510R*3 GD555-3 GD510R*3 GD555-3
GD511A*3 GD511A*3
*: SCARIFIER LOAD: When the scarifier and rear tires support the machine's weight.
*3: Including the scarifier bracket weight.
[ ] : When installing the adjustable type lifting rod
5A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
Model
600 SERIES
Item
NO.OF TEETH 11
ADDITIONAL WEIGHT: Standard Teeth Point Teeth
To operating weight +710 (+1,570) [+720 (+1,590)] +715 (+1,580) [+725 (+1,600)]
kg (lb)
To front axle +615 (+1,360) [+620 (+1,370)] +615 (+1,360) [+625 (+1,380)]
To rear axle +95 (+210) [+100 (+220)] +100 (+220) [+100 (+220)]
DIMENSIONS:
A: Distance between teeth mm (ft.in) 970 (3'2") 850 (2'9")
and center of front tire
SCARIFIER LOAD* kg (lb) 5055 ~ 5125 (11,140 ~ 11,300) 4753 ~ 5435 (10,480 ~ 11,980)
SCARIFIER RANGE:
Digging angle degree 63 ~ 76 53 ~ 66
Max. lift above ground mm (ft.in) 320 (1'1") 300 (1')
Max. digging depth mm (ft.in) 270 (10.6") 270 (10.6")
SCARIFIER EQUIPMENT:
Type V-type, 2-stage adjustable V-type, 2-stage adjustable
Weight kg (lb) 710 (1,570) 715 (1,580)
B: Digging width mm (ft.in) 1325 (4'4") 1350 (4'5")
Tooth:
As-installed mm (in) 275 × 77 × 25 185 × 50 × 36.3
Height × width × thickness (10.8" × 3.0" × 1.0") (7.3" × 2.0" × 1.4")
APPLICABLE MODEL GD611A*3 GD611A*3
GD661A*3 GD661A*3
Model
600 SERIES
Item
NO. OF TEETH 11
ADDITIONAL WEIGHT: kg (lb) Standard Teeth Point Teeth
To operating weight +640 (+1,410) +645 (+1,420)
[+650 (+1,430)] [+655 (+1,440)]
To front axle +535 (1,180) +545 (1,200)
[+545 (+1,200)] [+555 (+1,220)]
To rear axle +105 (+230) +100 (+220)
[+105 (+230)] [+100 (+220)]
DIMENSIONS:
A: Distance between teeth mm (ft.in) 980 (3'3") 935 (3'1")
and center of front tire
SCARIFIER LOAD* kg (lb) 5670 (12,500) 5635 (12,420)
SCARIFIER RANGE:
Digging angle degree 62 ~ 77 52 ~ 68
Max. lift above ground mm (ft.in) 370 (1'3") 340 (1'1")
Max. digging depth mm (ft.in) 245 (9.6") [345 (1'2")] 250 (9.8") [345 (1'2")]
SCARIFIER EQUIPMENT:
Type V-type, 2-stage adjustable V-type, 2-stage adjustable
Weight kg (lb) 640 (1,410) 645 (1,420)
B: Digging width mm (ft.in) 1405 (4'7") 1430 (4'8")
Tooth:
As-installed 275 × 77 × 25 185 × 50 × 36.3
Height × width × thickness mm (in) (10.8" × 3.0" × 1.0") (7.3" × 2.0" × 1.4")
APPLICABLE MODEL GD655-3A, GD675-3A GD655-3A, GD675-3A
*: SCARIFIER LOAD: When the scarifier and rear tires support the machine's weight.
*3: Including the scarifier bracket weight.
[ ] : When installing the adjustable type lifting rod.
5A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Model GD705A-4
Item
NO. OF TEETH 11
ADDITIONAL WEIGHT: kg (lb) Standard Teeth Point Teeth
To operating weight +1040 (+2,290) +1050 (+2,310)
To front axle +880 (+1,940) +890 (+1,960)
To rear axle +160 (+350) +160 (+350)
DIMENSIONS:
A: Distance between teeth mm (ft.in) 890 (2'11') 830 (2'9")
and center of front tire
SCARIFIER LOAD* kg (lb) 6690 (14,750) 6630 (14,620)
SCARIFIER RANGE:
Digging angle degree 54~67.5 49~63
Max. lift above ground mm (ft.in) 630 (2'1") 610 (2')
Max. digging depth mm (ft.in) 350 (1'2") 350 (1'2")
SCARIFIER EQUIPMENT:
Type V-type, 2-stage adjustable V-type, 2-stage adjustable
Weight kg (lb) 1040 (2,290) 1050 (2,310)
B: Digging width mm (ft.in) 1325 (4'4") 1350 (4'5")
Tooth:
As-installed 265 × 77 × 25 185 × 50 × 36.3
Height × width × thickness mm (in) (10.4 × 3.0 × 1.0) (7.3 × 2.0 × 1.4)
APPLICABLE MODEL GD705A GD705A
*: SCARIFIER LOAD: When the scarifier and rear tires support the machine's weight.
[ ] : When installing the adjustable type lifting rod.
5A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
Model GD705A-4
Item
ADDITIONAL WEIGHT:
To operating weight kg (lb) +970 (+2,140)
To front axle +1100 (+2,450)
To rear axle (140 (–310)
ADDITIONAL OVERALL
LENGTH:
A: Distance between blade mm (ft.in) 1610 (5'3")
edge and center of front
tire
BLADE RANGE:
Digging angle degree 55
Max. lift above ground mm (ft.in) 555 (1'10")
Max. drop below ground mm (ft.in) 110 (4.3")
BLADE EQUIPMENT:
Type Front arc, box section type
hydraulically controlled
Weight kg (lb) 910 (2,010)
Length × height mm (ft.in) 2500 × 850
(8'2" × 2'9")
APPLICABLE MODEL GD705A
*: As the front counterweight is removed when installing the front blade, "Additional weight" differs from "Blade weight".
5A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
5A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
5A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
5A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
ROPS cab
ROPS canopy
Steel cab
Canopy
Rear under
Extension blade view mirror
Hydraulic tip control
Blade accumulator
Blade float
Rear mounted ripper
5A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
Description Features
ROPS (Roll Over Protective Structure) cab
The combination of ROPS and a steel cab ensures
safety in places where there is danger of the machine
turning over and to protect the operator from wind, rain,
cold, sand and sun.
Low profile and full height cabs are available. Full height
ROPS cab is 90 mm (3.5")higher than the low profile
cab.
ROPS canopy
5A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
Description Features
Front blade
Push plate
Scarifier
This attachment digs up hard ground, like asphalt, old
pavement and frozen surfaces cannot be removed by
the blade. The number of teeth used depends upon the
ground hardness.
High-strength alloy steel tips can be mounted on the
teeth to prevent tooth wear and extend their service for
economical performance.
Extension blade
Blade accumulator
5A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
Description Features
Blade float
Wet type disc brake The brakes are sealed type, so no water or mud can get
in.
This ensures stable braking at all times. Oil lubrication
means wear is kept to the minimum, so the brakes are
maintenance free.
The brakes are operated pneumatically, so a small
operating effort of brake pedal gives secure braking.
There are two brake circuits, so even if one of the air
circuits should be damaged, it is still possible to brake
the machine.
Air dryer
5A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 5B
VIBRATORY ROLLERS
CONTENTS
Features .................................................................... 5B-2
Specifications ........................................................... 5B-3
Dimensions ............................................................... 5B-5
5B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
5B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
JV06H-3 JV08H-3 JV25CW-3 JV25DW-3
Item
WEIGHT (approx.):
Operating weight kg (lb) 600 (1,320) 700 (1,540) 2440 (5,380) 2560 (5,640)
Weight distribution:
Front drum 250 (550) 300 (660) 1350 (2,980) 1250 (2,760)
Rear drum 350 (770) 400 (880) 1090 (2,400) 1310 (2,890)
Flywheel horsepower HP (kW)/RPM 4.9 (3.7)/2200 6.1 (4.6)/2000 25.3 (18.9)/2300 25.3 (18.9)/2300
PERFORMANCE:
Travel speed: km/h (MPH)
Forward and reverse 1st 4.0 (2.5) 4.0 (2.5) 10.0 (6.2) 10.0 (6.2)
2nd — — — —
Cycle of vibration: CPM
Front drum 3300 3300 3300 3300
Rear drum 3300 3300 — 3300
Centrifugal force: kg (lb)
Front drum 600 (1320) 750 (1650) 2100 (4630) 2100 (4630)
Rear drum 600 (1320) 750 (1650) — 2100 (4630)
Compacting width mm (ft.in) 600 (2') 700 (2'4") 1200 (3'11") 1200 (3'11")
Turning radius m (ft.in) — — 3.8 (12'6") 3.8 (12'6")
ENGINE: YAMMAR YAMMAR KOMATSU KOMATSU
Model NFAD6 NFAD8 3D84E 3D84E
No. of cylinders- 1–74 × 72 1–78 × 80 3 – 84 × 90 3 – 84 × 90
bore × stroke mm (in) (2.9 1 × 2.83) (3.07 × 3.15) (3.3 × 3.54) (3.3 × 3.54)
Piston displacement ltr. (in3) 0.309 (18.9) 0.382 (23.3) 1.496 (91.3) 1.496 (91.3)
TRANSMITTING SYSTEM:
Transmission HST HST HST HST
Gearshift Stepless Stepless Stepless Stepless
Reverser Swash-plate Swash-plate Swash-plate Swash-plate
type type type type
Variable- Variable- Variable- Variable-
capacity pump capacity pump capacity pump capacity pump
Final drive Spur gear Spur gear Planetary gear Planetary gear
CAPACITY:
Fuel tank ltr. (U.S. Gal) 5.6 (1.48) 7.1 (1.9) 36 (9.5) 36 (9.5)
Model
JV40DW-5 JV40CW-5 JV100A-2 JV100WP-2
Item
WEIGHT (approx.):
Operating weight kg (lb) 4000 (8,820) 3600 (7,940) 10100 (22,270) 11250 (24,800)
Weight distribution:
Front drum 2000 (4,410) 2000 (4,410) 5300 (11,680) 5950 (14,220)
Rear drum 2000 (4,410) 1600 (3,530) 4800 (10,580) 4800 (10,580)
Flywheel horsepower HP (kW)/RPM 27.6 (20.6)/2550 27.6 (20.6)/2550 133 (99.2)/2000 133 (99.2)/2000
PERFORMANCE:
Travel speed: km/h (MPH)
Forward and reverse 1st 8.0 (5.0) 8.7 (5.4) 8.3 (6.2) 6.0 (3.7)
2nd 10.5 (6.5) 12.0 (7.5) 14.1 (8.8) 11.0 (6.8)
Cycle of vibration: CPM
Front drum 3300 3300 1000~1850 1000~1800
Rear drum 3300 — — —
Centrifugal force: kg (lb)
Front drum 2500 (5,510) 2500 (5510) 6200 (13,670)~ 7300 (16,090)~
23700 (52,250) 23700 (52,250)
Rear drum 2500 (5,510) — —
Compacting width mm (ft.in) 1300 (4'3") 1300 (4'3") 2130 (7') 2130 (7')
Turning radius m (ft.in) 4.3 (14'1") 4.3 (14'1") 5.7 (18'8") 5.7 (18'8")
ENGINE: KOMATSU KOMATSU KOMATSU KOMATSU
Model 3D84E 3D84E S6D102E S6D102E
No. of cylinders- 3 – 84 × 86 3 – 84 × 86 6 –102 × 120 6 –102 × 120
bore × stroke mm (in) (3.3 × 3.39) (3.3 × 3.39) (4.02 × 4.72) (4.02 × 4.72)
Piston displacement ltr. (in3) 1.429 (87.2) 1.429 (87.2) 5.88 (359) 5.88 (359)
TRANSMITTING SYSTEM:
Transmission HST HST HST HST
Gearshift Stepless Stepless 2-forward, 2-forward,
Reverser Swash-plate Swash-plate 2-reverse 2-reverse
type type Swash-plate Swash-plate
Variable- Variable- type type
capacity pump capacity pump Variable- Variable-
capacity pump capacity pump
Final drive Planetary gear Planetary gear Planetary gear Planetary gear
CAPACITY:
Fuel tank ltr. (U.S. Gal) 47 (12.4) 47 (12.4) 260 (68.7) 260 (68.7)
5B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Model
JV100WA-2
Item
WEIGHT:
Operating weight kg (lb) 10750 (23,700)
Weight distribution:
Front drum 5950 (13,120)
Rear drum 4800 (10,580)
Flywheel horsepower HP (kW)/RPM 133 (99.2)/2000
PERFORMANCE:
Travel speed: km/h (MPH)
Forward and reverse 1st 6.0 (3.7)
2nd 11.0 (6.8)
Cycle of vibration: CPM
Front drum 1000~1800
Rear drum —
Centrifugal force: kg (lb)
Front drum 3500 (7720)~
23700 (52,250)
Rear drum —
Compacting width mm (ft.in) 2130 (7')
Turning radius m (ft.in) 5.7 (18'8")
ENGINE: KOMATSU
Model S6D102E
No. of cylinders- 6 –102 × 120
bore × stroke mm (in) (4.02 × 4.72)
Piston displacement ltr. (in3) 5.88 (359)
TRANSMITTING SYSTEM:
Transmission HST
Gearshift 2-forward,
Reverser 2-reverse
Swash-plate
type
Variable-
capacity pump
Final drive Planetary gear
CAPACITY:
Fuel tank ltr. (U.S. Gal) 260 (68.7)
5B-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
D
D C
C
O B
R O B
R L
W
W
L
Unit : mm (ft.in)
JV06H-3 JV08H-3 JV25DW-3
650 750 1290
W
(2'2") (2'6") (4'3")
2370 2585 2625
L
(7'9") (8'6") (8'7")
1075 1100 1570
H
(3'6") (3'7") (5'2")
600 700 1200
R
(2') (2'4") (3'11")
520 570 1950
B
(1'8") (1'10") (6'5")
230 225 337.5
O
(9") (9") (1'1")
220 250 280
C
(8") (10") (11")
355 406 675
D
(1'2") (1'4") (2'3")
JV25CW-3
JV40CW-5
D
ø
C
O B
R L
W
Unit : mm (ft.in)
JV25CW-3 JV40DW-5 JV40CW-5 JW40CW-5*
1290 1390 1390 1390
W
(4'3") (4'8") (4'8") (4'8")
2623 3100 3105 3105
L
(8'7") (10'2") (10'2") (10'2")
1570 1730 1730 1730
H
(5'2") (5'8") (5'8") (5'8")
1200 1300 1300 1300
R
(3'11") (4'3") (4'3") (4'3")
1950 2300 2300 2300
B
(6'5") (7'7") (7'7") (7'7")
337.5 400 400 400
O
(1'1") (1'4") (1'4") (1'4")
280 280 280 280
C
(11") (11") (11") (11")
675 800 800 800
D
(2'3") (2'7") (2'7") (2'7")
* : With wide tires
5B-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
X X
H A
D WR r T
C A
B
L FVBH0300
Unit: mm (ft.in)
JV100A-2 JV100WP-2 JV100WA-2
2350 2350 2350
W
(7'9") (7'9") (7'9")
5600 5600 5600
L
(18'4") (18'4") (18'4")
2950 2950 2950
*H
(9'8") (9'8") (9'8")
2130 2130 2130
R
(7') (7') (7')
1532 1532 1532
r
(5') (5') (5')
2130 2130 2130
T
(7') (7') (7')
A 36° 36° 36°
2985 2985 2985
B
(9'10") (9'10") (9'10")
410 410 410
C
(1'4") (1'4") (1'4")
1520 1520 1520
D
(5') (5') (5')
d — — —
5B-6
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 5C
TIRE ROLLER
CONTENTS
Features .................................................................... 5C-2
Specifications ........................................................... 5C-3
5C-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
5C-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
JW30-2
Item
WEIGHT (approx.):
Operating weight kg (lb) 3000 (6,610)
Weight distribution:
Front wheel 1770 (3,900)
Rear wheel 1230 (2,710)
Flywheel horsepower HP (kW)/RPM 21.3 (15.9)/2400
PERFORMANCE:
Travel speed: km/h (MPH)
Forward and reverse 13.0 (8.1)
Compacting width mm (ft.in) 1300 (4'3")
Side overhang mm (in)
Left 90 (3.5")
Right 90 (3.5")
Turning radius m (ft.in) 3.8 (12'6")
ENGINE: KOMATSU
Model 3D82AE
No. of cylinders- mm (ft.in) 3 – 82 × 84
bore × stroke (3.23 × 3.31)
Piston displacement ltr. (in3) 1.33 (81.2)
TRANSMITTING SYSTEM:
Transmission HST
Gearshift Stepless
Reverser Swash-plate
type
variable-
capacity pump
Final drive Chain type
Tires
Front tire 9.50/65-15PR × 4
Rear tire 9.50/65-15PR × 4
CAPACITY:
Fuel tank ltr. (U.S. Gal) 36 (9.5)
Dimensions
1710(5'6")
9. 9.
5/6 5-15 200 (7.9") 5/6 5-15
243 243 243 243 335(1'1") 1900(6'3") 415(1'4") 243 243 243
(9.6") (9.6") (9.6") (9.6") (9.6") (9.6") (9.6")
2650(8'8")
1300(4'3") 945(3'1")
5C-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 5D
OTHER ROAD MAINTENANCE
EQUIPMENT
CONTENTS
Komatsu's recommendation ................................... 5D-2
Road subgrade recycling method .......................... 5D-2
Asphalt-pavement profiling method ....................... 5D-3
Road maintenance equipment ................................ 5D-4
Wheel stabilizer ........................................................ 5D-5
Crawler stabilizers ................................................... 5D-6
Road cutters ............................................................. 5D-8
Stone crusher ........................................................... 5D-9
5D-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
5D-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
5D-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
2. Lime spreader
In conventional operations, lime or other soil stabilizing agents or soil improvement are spread over the
ground manually or through the use of hydraulic excavators.
3. Crawler stabilizer
This is Komatsu's efficient alternative to conventional road subbase rehabilitation/improvement methods,
especially where the ground is soft, owing to the use of hydraulic exacavators or intensive, physical labor.
A single passage of the crawler stabilizer effectively crumbles old pavements; a stabilizing agent is mixed,
and the crushed materials are then used as the subbase material for the new pavement. Two digging
depths are available. The CS360SD can dig down to 1.2 meters (3'11''), the CS360 down to 0.7 meters
(2'4''), and the CS210 down to 0.6 meters (2').
4. Road cutters
Usually, uneven road surfaces and ruts are removed by road cutters. In this case, the dirt is removed
manually.
Komatsu's GC380F, which comes with a feeder, effectively scrapes jutting road surfaces and automatically
loads the waste into a dump truck. Another advantage is that a single operator of less experience can
control this machine with the equal skill of two veteran operators.
5. Motor Graders
Komatsu provides an excellent range of motor graders in various sizes depending on specific grading
requirements.
6. Vibratory rollers
Komatsu also offers a wide range of vibratory rollers in various configurations depending on specific
compaction requirements .
5D-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
The GS360 Wheel Stabilizer is designed for rehabilitation of old, damaged roads and
for soil Improvement tasks in farmland or around housing developments. When it
comes to reducing working time and costs, the GS360 is the answer for any type of
road / soil subbed rehabilitation.
Exceptional productivity:
The powerful digging force easily breaks down asphalt pavements up to 150 mm
(5.9") thick, and digs down to 400 mm (15.7") to perform simultaneous crumbling and
mixing operations. The optional rotor enables digging / mixing operation even down
to a depth of 700 mm (2'4").
Uniform crumbling and mixing:
Rotor tilting operation is possible due to the left-right individual control of the rotor lift.
The up-cut method and effect of the secondary crusher make granule / subbase soil
mixing work very efficient.
Rotor offset of 285 mm (11.2") to the left and right beyond the
outer edge of the tires
Stable rotor operation:
The tandem drive wheels and central placement of the rotor assure that, even on
rough and tough roads, there is very little vertical movement of the rotor, and traction
remains powerful, securing constant cutting depth.
In-the-field rotor disc replacement:
The discs can be easily assembled and disassembled with a few bolts. For extra
convenience, the bits are tapered and are attached by being hammered into place,
thus facilitating replacement.
Specifications
GS360-2
Digging width mm (ft.in) 1975 (6'6")
Max. digging depth mm (in) 400 (15.7')
Engine output HP (kW) 355 (265)
Operating weight kg (lb) 18200 (40,120)
Rotor shift distance (LH & RH both) mm (ft.in) 500 (1'8")
Overhang distance (LH & RH both) mm (in) 295 (11.8")
PERFORMANCE
Travel speed km/h (MPH) 0-25 (15.5)
Working speed m/min (MPH) 0-50 (1.9)
Max. drawbar pull kg (lb) 9480 (20,900)
ENGINE
Model Komatsu S6D140
Type Direct injection,turbocharged
No. of cylinders-bore × stroke mm (in) 6-140 × 165 (5.51 × 6.50)
Flywheel horsepower HP (kW) 355 (265)
ROTOR EQUIPMENT
Drive method Hydrostatic
Rotor speed rpm 0-132
No. of cutting bits 52
REFILLING CAPACITY
Fuel ltr. (U.S. Gal) 500 (132.1)
Hydraulic oil ltr. (U.S. Gal) 300 (79.3)
ATTACHMENTS AND OPTIONAL EQUIPMENT
• Steel cab • Tool kit
• Canopy • Wide tire 17.5-25-12PR (G-2)
• Working equipment
Road planer
Digging depth 500m (19.7") rotor for FRB
Digging depth 600 mm ~ 700 mm (23.6" ~ 27.6")
rotor for soil stabilizing
Soft rock crusher
(Drum type rotor and conical bits are used )
5D-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
5D-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
CS360-2
CS210-1 CS360-2
Max. mixture depth mm (ft.in) 600 (2') 700 (2'4")
Digging width mm (ft.in) 1600 (5'3"), *1800 (5'11") 2000 (6'7")
Engine output HP (kW) 203 (152) 355 (265)
16110 (35,520),
Operating weight kg (lb) 24400 (53,790)
*16305 (35,950)
Rotor shift distance (LH & RH both) mm (ft.in) 515 (1'8"),*415 (1'4") 500 (1'8")
Overhang distance (LH) mm (in) 140 (5.5) 170 (6.7")
Ground pressure kg/cm2 (PSI) 0.53 (7.5), *0.54 (7.7) 0.38 (5.40)
DIMENSIONS
Overall length × overall width 7500 × 2350 × 2630 9500 × 2980 × 3640
mm (ft.in)
× overall height (24'7" × 7'9" × 8'8") (31'2" × 9'9" × 11'11")
Length of track on ground mm (ft.in) 2750 (9') 3840 (11'11")
Shoe width mm (in) 500 (20) 860 (34')
Ground clearance mm (ft.in) 330 (1'1") 540 (1'9")
PERFORMANCE
Travel speed km/h (MPH) 0-3.1 (1.9) 0-3.2 (2.0)
Working speed m/min (MPH) 0-10 (0.4) 0-10 (0.4)
Max. drawbar pull kg (lb) 10100 (22,270) 12000 (26,455)
Gradeability deg 20 20
ENGINE
Model Komatsu S6D125E Komatsu SA6D140E
Type Direct injection, turbocharged Direct injection, turbocharged
No. of cylinders-bore × stroke mm (in) 6-125 × 150 (4.92 × 5.91) 6-140 × 165 (5.51 × 6.50)
Flywheel horsepower HP (kW) 203 (152) 355 (265)
ROTOR EQUIPMENT
Drive method Hydrostatic Hydrostatic
Rotor speed rpm 0-143 0-130
No. of cutting bits 52, *56 60
REFILLING CAPACITY
Fuel ltr. (U.S. Gal) 300 (186) 500 (132.1)
Hydraulic oil ltr. (U.S. Gal) 115 (71) 300 (79.3)
CS360-2 ATTACHMENTS AND OPTIONAL EQUIPMENT
• Steel cab
• 700 mm (27.6") triple grouser shoes
• 860 mm (34") swamp shoes
5D-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Specifications
GC380F-2
OPERATING WEIGHT kg (lb) 28960 (63850)
On front wheel kg (lb) 11400 (25130)
On rear wheel kg (lb) 17560 (38710)
PERFORMANCE
Travel speed F and R 1st km/h (MPH) 0 ~ 4.8
F and R 2nd km/h (MPH) 0-26.0 (16.2)
Working speed m/min (MPH) 30 (1.1)
Max. rimpull kg (lb) 14048 (30970)
Min turning radius m (ft.in) 12 (39'4")
Tire size 14.00-24-16PR
ENGINE
Model Komatsu SA6D140
Flywheel horsepower HP (kW)/rpm 488 (364)/2000
Piston displacement ltr. (cu.in) 15.24 (928)
WORK EQUIPMENT
Drive method Hydrostatic
Rotor side shift distance mm (ft.in) 450 (1'6")
Cutting depth mm (in) 150 (5.91)
Accuracy of cutting depth mm (in) ±2 (±0.079)
Cutting width mm (ft.in) 2070 (6'10")
REFILLING CAPACITY
Fuel ltr. (U.S. Gal) 700 (185)
Hydraulic oil ltr. (U.S. Gal) 243 (64)
Sprinkler tank ltr (US qal) 2000 (528)
5D-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Conical bit
Rebound plate
Splintering plate
Selection plate
• The substantial working depth of 315 mm (12.4") reduces the burden on machines at the next processes.
• High splintering performance: 90 - 95% by weight of splintered stones are less than 30 mm (1.2") in
diameter.
Specifications
CS210-1
Operating weight kg (lb) *17960 (39,590)
Flywheel horsepower HP (kW) 203 (152)
Travel speed km/h (MPH) 0~3.1 (1.93)
Working speed m (ft)/min 0~10.0 (32.8)
Working width mm (ft.in) 2060 (6'9")
Working depth mm (in) 315 (12.4")
Ground pressure kg/cm2 (PSI) 0.39 (5.5)
Overall length mm (ft.in) 7600 (24'11")
Overall width mm (ft.in) 2450 (8')
Overall height (to top of cab) mm (ft.in) 2630 (8'8")
Engine model Komatsu S6D125E
Type of stone crusher Rotary drum type
Number of bits Conical bits: 106, Roof bits: 10
Rotor speed rpm 0 ~ 127
Rotor width mm (ft.in) 2000 (6'9")
Rotor diameter mm (ft.in) 1072 (3'6")
Transmission type Hydrostatic drive
* With cab and 750 mm (30") triple grouser shoes.
5D-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 6
INDEX
BACKHOE LOADERS
CONTENTS
Features .......................................................................6-2
Specifications ..............................................................6-3
Dimensions ..................................................................6-4
6-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Superior lift capacities and breakout A high steering angle combined with
forces excellent maneuverability result in
• Komatsu's superior lift capacities and breakout fast cycle times for the operator.
forces are achieved exclusively through the
HydrauMind hydraulic system.
• The front loader has superb breakout forces and Komatsu's backhoe loaders are
lift capacity due in part to the unique design of the equipped with Power Shuttle
loader.
transmissions and "Power shift"
inverters.
Komatsu's ergonomic innovations
create the perfect operating
environment. Komatsu's Electronic Gear
Management (EGM) system allows
• We ergonomically designed the controls
offering ease of operation, using a hydraulic the operator to utilize the Powershift
system that responds smoothly and precisely. transmission in either manual or
• The cab allows for all-around visibility and is automatic mode.
extremely quiet.
The Komatsu Powershift transmission has been
• The ergonomically designed suspension seat designed to safely allow the operator to perform
is very comfortable and fully adjustable. all functions efficiently. In addition to offering two
modes of operation, the Powershift comes
standard with:
Multi-function loader control lever's
• Self diagnostics system
cutting edge design allows for
• Anti-theft system
fingertip operation of all key loader • Engagement and automatic disengagement of
functions. four wheel drive
• Transmission disconnect • Kick down switch
• Auxiliary hydraulic control
• Rear differential lock
• Hydraulic speed up function
• Kick down (PS version only)
6-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
WB70A-1 WB91R-2 WB93R-2 WB97R-2
Item
OPERATING WEIGHT* kg (lb) 5650 (12,460) 7590 (16,730) 7590 (16,730) 7590 (16,730)
FLYWHEEL HORSEPOWER
SAE HP (kW)/rpm 70.8 (52)/2500 82.5 (61.5)/2200 97.8 (73)/2200 97.8 (73)/2200
BUCKET CAPACITY* m3 (cu.yd) 0.7 (0.92) 1.03 (1.35) 1.03 (1.35) 1.03 (1.35)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward Working 1st 4.7 (2.9) 6.5 (4.0) 6.5 (4.0) 6.5 (4.0)
2nd 10.5 (6.5) 12 (7.5) 12 (7.5) 12 (7.5)
Travel 3rd 18 (11) 23 (14) 23 (14) 23 (14)
4th 39 (24) 40 (25) 40 (25) 40 (25)
Reverse Working 1st 4.7 (2.9) 6.5 (4.0) 6.5 (4.0) 6.5 (4.0)
2nd 10.5 (6.5) 12 (7.5) 12 (7.5) 12 (7.5)
Travel 3rd 18 (11) 23 (14) 23 (14) 23 (14)
4th 39 (24) 40 (25) 40 (25) -
Turning radius* mm (ft.in) 4380 (14'4") 5450 (17'11") 5450 (17'11") 5450 (17'11")
(Outside corner of bucket)
DIMENSIONS*:
Overall length*** mm (ft.in) 5270 (17'3") 5895 (19'4") 5895 (19'4") 5895 (19'4")
Overall width mm (ft.in) 1850 (6'1") 2320 (7'7") 2320 (7'7") 2320 (7'7")
Overall height** mm (ft.in) 2660 (8'9") 2750 (9') 2750 (9') 2750 (9')
Wheelbase mm (ft.in) 2150 (7'1") 2175 (7'2") 2175 (7'2") 2175 (7'2")
Treads (front) mm (ft.in) 1490 (4'10") 1934 (6'4") 1934 (6'4") 1934 (6'4")
Treads (rear) mm (ft.in) 1490 (4'10") 1780 (5'10") 1780 (5'10") 1780 (5'10")
Articulation angle (each) degree 40 — — —
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
No. of cylinders- 4D98E-1FA 4D106-1FA S4D106-1FA S4D106-1FA
bore × stroke mm (in) 4-98 × 110 4-106 × 125 4-106 × 125 4-106 × 125
(3.9 × 4.3) (4.2 × 4.9) (4.2 × 4.9) (4.2 × 4.9)
Piston displacement ltr. (cu.in) 3.32 (203) 4.41 (269) 4.41 (269) 4.41 (269)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 70 (18.5) 130 (34.3) 130 (34.3) 130 (34.3)
Model
WB97S-2 WB98A-2 WB140-2 WB150-2
Item
OPERATING WEIGHT* kg (lb) 8190 (18,060) 8290 (18,280) 7525 (16,600) 7890 (17,400)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 97.8 (73)/2200 96.5 (72)/2200 86 (64.1)/2200 98 (73)/2200
BUCKET CAPACITY* m3 (cu.yd) 1.10 (1.43) 1.10 (1.43) 0.95 (1.25) 0.95 (1.25)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward Working 1st 6.5 (4.0) 6.5 (4.0) 6.3 (3.9) 6.3 (3.9)
2nd 12 (7.5) 12 (7.5) 11.4 (7.1) 11.4 (7.1)
Travel 3rd 23 (14.3) 20 (12) 21.3 (13.2) 21.3 (13.2)
4th 40 (25) 36 (22) 37.8 (23.5) 37.8 (23.5)
Reverse Working 1st 6.5 (4.0) 6.5 (4.0) 6.3 (3.9) 6.3 (3.9)
2nd 12 (7.5) 12 (7.5) 11.4 (7.1) 11.4 (7.1)
Travel 3rd 23 (14.3) 20 (12) 21.3 (13.2) 21.3 (13.2)
4th - 36 (22) 37.8 (23.5) 37.8 (23.5)
Turning radius* mm (ft.in) 4390 (14'5") 4680 (15'4") 5500 (18'1") 5500 (18'1")
(Outside corner of bucket)
DIMENSIONS*:
Overall length*** mm (ft.in) 5895 (19'4") 5575 (18'3") 6125 (20'1") 6125 (20'1")
Overall width mm (ft.in) 2420 (7'11") 2250 (7'5") 2355 (7'9") 2355 (7'9")
Overall height** mm (ft.in) 2810 (9'3") 2920 (9'7") 2750 (9'0") 2750 (9'0")
Wheelbase mm (ft.in) 2175 (7'2") 2355 (7'9") 2170 (7'1") 2170 (7'1")
Treads (front) mm (ft.in) 1950 (6'5") 1650 (5'5") 1890 (6'2") 1890 (6'2")
Treads (rear) mm (ft.in) 1950 (6'5") 1650 (5'5") 1800 (5'11") 1800 (5'11")
Articulation angle (each) degree — 40
ENGINE:
KOMATSU KOMATSU KOMATSU KOMATSU
No. of cylinders- S4D106-2SFA S4D106E-1FC S4D106-1FH S4D106-1FA
bore × stroke mm (in) 4-106 × 125 4-106 × 125 4-106 × 125 4-106 × 125
(4.2 × 4.9) (4.2 × 4.9) (4.2 × 4.9) (4.2 × 4.9)
Piston displacement ltr. (cu.in) 4.41 (269) 4.41 (269) 4.41 (269) 4.41 (269)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 130 (34.3) 110 (29.1) 130 (34.3) 130 (34.3)
* With standard tires and bucket
** Height to top of the cab
*** Transport length
6-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
AA
J K
Y
W
DD
CC
F
U
A
H
S'
C
T
D
N'
B
L M N
O
V
Q
R
FVBH0332
A B C D E F G H I L M N
mm mm mm mm deg. deg. deg. mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
3885 110 3125 2480 46 40 44 870 440 1650 2150 1470
WB70A-1
(12'9") (4.3") (10'3") (8'2") (2'10") (1'5") (5'5") (7'1") (4'10")
4340 75 3470 2790 43 42 54 895 440 1770 2355 1450
WB98A-2
(14'3") (3.0") (11'5") (9'2") (2'11") (1'5") (5'10") (7'9") (4'9")
6-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Q
M
O
F
E
A
N
B
BB
C
D
G
J
I K L
H
P
S
T
R
X
Y
U
V
Z W
FVBH0330
A B BB C D E F G H I J K L
mm mm mm mm mm mm deg. deg. mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
4220 3400 3200 2750 2750 750 45 45 110 1930 430 2175 1320
WB91R-2
(13'1") (11'2") (10'6") (9') (9') (2'6") (4.3") (6'4") (1'5") (7'2") (4'4")
4220 3400 3200 2750 2750 750 45 45 110 1930 430 2175 1320
WB93R-2
(13'1") (11'2") (10'6") (9') (9') (2'6") (4.3") (6'4") (1'5") (7'2") (4'4")
4220 3400 3200 2750 2750 750 45 45 110 1930 430 2175 1320
WB97R-2
(13'1") (11'2") (10'6") (9') (9') (2'6") (4.3") (6'4") (1'5") (7'2") (4'4")
4220 3440 3200 2810 2750 750 45 45 110 1930 470 2175 1320
WB97S-2
(13'1") (11'3") (10'6") (9'3") (9') (2'6") (4.3") (6'4") (1'7") (7'2") (4'4")
M N O P Q R S T U V W X Y Z
mm mm mm mm mm mm mm mm mm mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
5895 3700 5510 4500 2500 5550 4950 2750 1780 1934 2320 3660 1080 1150
WB91R-2
(19'4") (12'2") (18'1") (14'9") (8'2") (18'3") (16'3") (9') (5'10") (6'4") (7'7") (12') (3'7") (3'9")
5895 3700 5510 4500 2500 5550 4950 2750 1780 1934 2320 3660 1080 1150
WB93R-2
(19'4") (12'2") (18'1") (14'9") (8'2") (18'3") (16'3") (9') (5'10") (6'4") (7'7") (12') (3'7") (3'9")
5895 3700 5510 4500 2500 5550 4950 2750 1780 1934 2320 3660 1080 1150
WB97R-2
(19'4") (12'2") (18'1") (14'9") (8'2") (18'3") (16'3") (9') (5'10") (6'4") (7'7") (12') (3'7") (3'9")
5895 3700 5510 4500 2500 5550 4950 2750 1950 1950 2420 3660 1080 1150
WB97S-2
(19'4") (12'2") (18'1") (14'9") (8'2") (18'3") (16'3") (9') (6'5") (6'5") (7'11") (12') (3'7") (3'9")
6-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Q
M
F
O
E
B
N
C
D
G
J
H
I K L
P
S
X
U
T
V R
W
FVBH0331
A B C D E F G H I J K L
mm mm mm mm mm deg. deg. mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
4185 3365 2750 2750 670 45 45 90 2080 320 2170 1175
WB140-2
(13'9") (11'0") (9') (9') (2'2") (4.0") (6'10") (1'1") (7'1") (3'10)
4185 3365 2750 2750 670 45 45 90 2080 320 2170 1175
WB150-2
(13'9") (11'0") (9') (9') (2'2") (4.0") (6'10") (1'1") (7'1") (3'10)
M N O P Q R S T U V W X
mm mm mm mm mm mm mm mm mm mm mm mm
(ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in) (ft.in)
6125 3490 4930 4420 2860 5520 5590 2750 1800 1890 2355 3550
WB140-2
(20'1") (11'5") (16'2") (14'6") (9'5") (18'1") (18'4") (9') (5'11") (6'2") (7'9") (11'8")
6125 3710 5155 4725 3100 5715 5590 2750 1800 1890 2355 3550
WB150-2
(20'1") (12'2") (16'11") (15'5") (10'2") (18'9") (18'4") (9') (5'11") (6'2") (7'9") (11'8")
6-6
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 7
INDEX
CONTENTS
Features .......................................................................7-2
Specifications ..............................................................7-3
Dimensions ..................................................................7-4
7-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
• Versatility
The foot accelerator ensures greater control over
power during operation.
Ready for use with any equipment, the base
version features an auxiliary hydraulic circuit with
proportional control.
7-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model
SK04J-2 SK510-5 SK714-5 SK815-5
Item
OPERATING WEIGHT* kg (lb) 1550 (3,420) 1855 (4,090) 2530 (5,580) 2630 (5,800)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 20.8 (15.5)/2800 30.6 (22.5)/2800 47.2 (34.7)/2800 47.2 (34.7)/2800
BUCKET CAPACITY* m3 (cu.yd) 0.16 (0.21) 0.23 (0.30) 0.35 (0.46) 0.4 (0.52)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward Working 9 (5.6) 10 (6.2) 10.5 (6.5) 10.5 (6.5)
Trave 16 (9.9) 16 (9.9)
Reverse Working 9 (5.6) 10 (6.2) 10.5 (6.5) 10.5 (6.5)
Travel 16 (9.9) 16 (9.9)
Turning radius* mm (ft.in) 1465 (4'10'') 1697 (5'7") 2100 (6'11") 2150 (7'11")
(Outside corner of bucket)
DIMENSIONS*:
Overall length mm (ft.in) 2570 (8'5") 2917 (9'7") 3200 (10'6") 3350 (11'0")
Overall width mm (ft.in) 1080 (3'7") 1260 (4'2") 1550 (5'1") 1730 (5'8")
Overall height** mm (ft.in) 1860 (5'6") 1924 (6'4") 1960 (6'5") 1960 (6'5")
Wheelbase mm (ft.in) 740 (2'5") 823 (2'8") 950 (3'1") 1050 (3'5")
Treads (front and rear) mm (ft.in) 820 (2'8") 1010 (3'4") 1250 (4'1") 1380 (4'6")
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
3D74E 3D84E 4D88E 4D88E
No. of cylinders- mm (in) 3-74 × 78 3-84 × 86 3-88 × 90 3-88 × 90
bore × stroke (2.9 × 3.1) (3.3 × 3.4) (3.5 × 3.5) (3.5 × 3.5)
Piston displacement ltr. (cu.in) 1.01 (62) 1.43 (87) 2.19 (134) 2.19 (134)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 27 (7.1) 38.5 (10.2) 53 (14.0) 53 (14.0)
Model
SK818-5 SK820-5 SK1020-5 SK1026-5
Item
OPERATING WEIGHT* kg (lb) 2910 (6,415) 2940 (6,480) 3420 (7,540) 3790 (8,360)
FLYWHEEL HORSEPOWER:
SAE HP (kW)/rpm 47.2 (34.7)/2800 52.2 (38.9)/2800 69.5 (51.1)/2500 84 (62)/2500
BUCKET CAPACITY* m3 (cu.yd) 0.4 (0.52) 0.4 (0.52) 0.45 (0.59) 0.45 (0.59)
PERFORMANCE:
Travel speeds: km/h (MPH)
Forward Working 10 (6.2) 10.5 (6.5) 10 (6.2)
Travel 16 (9.9) 16 (9.9) 16 (9.9) 16 (9.9)
Reverse Working 10 (6.2) 10.5 (6.5) 10 (6.2)
Travel 16 (9.9) 16 (9.9) 16 (9.9) 16 (9.9)
Turning radius* mm (ft.in) 2150 (7') 2015 (6'7") 2155 (7') 1998 (6'7")
(Outside corner of bucket)
DIMENSIONS*:
Overall length mm (ft.in) 3350 (11'0") 3350 (11'0") 3550 (11'8") 3547 (11'8")
Overall width mm (ft.in) 1730 (5'8") 1730 (5'8") 1880 (6'2") 1880 (6'2")
Overall height** mm (ft.in) 2000 (6'7") 2000 (6'7") 2080 (6'10") 2082 (6'10")
Wheelbase mm (ft.in) 1050 (3'5") 1050 (3'5") 1160 (3'10") 1162 (3'10")
Treads (front and rear) mm (ft.in) 1385 (4'7") 1385 (4'7") 1500 (4'11") 1530 (5'0")
ENGINE:
Model KOMATSU KOMATSU KOMATSU KOMATSU
4D88E S4D84E 4D98E 4D98E
No. of cylinders- mm (in) 4-88 × 90 4-84 × 90 4-98 × 110 4-98 × 110
bore × stroke (3.46 × 3.54) (3.31 × 3.54) (3.85 × 4.33) (3.85 × 4.33)
Piston displacement ltr. (cu.in) 2.19 (133.6) 2.0 (122) 3.32 (203) 3.32 (203)
CAPACITY:
Fuel tank ltr. (U.S. Gal) 47 (12.4) 53 (14.0) 73 (19.3) 73 (19.3)
7-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Q M
N
K
J
L
G F E
H C
P D
A
B FVBH0216
Model
SK04J-2 SK510-5 SK714-5 SK815-5
Item
A: Wheel base mm (ft.in) 740 (2'5") 823 (2'8") 950 (3'1") 1050 (3'5")
B: Overall length mm (ft.in) 2570 (8'5") 2917 (9'7") 3200 (10'6") 3350 (11'0")
C: Overall height mm (ft.in) 1860 (6'1") 1924 (6'4") 1960 (6'5") 1960 (6'5")
D: Ground clearance mm (in) 175 (6.9") 184 (7.2") 210 (8.3") 210 (8.3")
1030 (3'5")
E: Width over tires mm (ft.in) 900 (2'11")* 1235 (4'1") 1520 (5'0") 1650 (5'5")
F : Tread mm (ft.in) 820 (2'8") 1010 (3'4") 1250 (4'1") 1380 (4'6")
1080 (3'7")
G: Bucket width mm (ft.in) 920 (3'0")* 1260 (4'2") 1550 (5'1") 1730 (5'8")
H: Dumping clearance, max. height mm (ft.in) 1940 (6'4") 2082 (6'10") 2140 (7'0") 2190 (7'2")
J : Reach at max. height mm (ft.in) 390 (1'3") 408 (1'4") 510 (1'8") 530 (1'9")
K: Operating height (fully raised) mm (ft.in) 3115 (10'3") 3483 (11'5") 3630 (11'11") 3730 (12'3")
L : Hinge pin height, max. height mm (ft.in) 2440 (8'0") 2707 (8'11") 2850 (9'4") 2920 (9'7")
M: Turning radius at bucket corner mm (ft.in) 1465 (4'10") 1697 (5'7") 2100 (6'11") 2150 (7'1")
N: Turning radius at rear tail corner mm (ft.in) 1267 (4'2") 1408 (4'7") 1340 (4'5") 1460 (4'9")
P: Tilt back angle, carry position degree 27 37 30 30
Q: Dump angle, max. height degree 36 38 45 45
Model
Item SK818-5 SK820-5 SK1020-5 SK1026-5
A: Wheel base mm (ft.in) 1050 (3'5") 1050 (3'5") 1160 (3'9") 1162 (3'10")
B: Overall length mm (ft.in) 3350 (11') 3480 (11'5") 3550 (11'7") 3547 (11'8")
C: Overall height mm (ft.in) 2000 (6'6") 2001 (6'7") 2080 (6'10") 2082 (6'10")
D: Ground clearance mm (in) 210 (8.26") 210 (8.26") 240 (9.44") 237 (9.33")
E: Width over tires mm (ft.in) 1660 (5'5") 1658 (5'5") 1840 (6') 1836 (6'0")
F : Tread mm (ft.in) 1385 (4'5") 1383 (4'6") 1500 (4'9") 1530 (5'0")
G: Bucket width mm (ft.in) 1730 (5'7") 1730 (5'8") 1880 (6'2") 1880 (6'2")
H: Dumping clearance, max. height mm (ft.in) 2280 (7'5") 2190 (7'2") 2390 (7'10") 2554 (8'5")
J : Reach at max. height mm (ft.in) 775 (2'6") 660 (2'2") 590 (2') 842 (2'9")
K: Operating height (fully raised) mm (ft.in) 3820 (12'6") 3910 (12'10") 3965 (13') 4115 (13'6")
L : Hinge pin height, max. height mm (ft.in) 3000 (9'10") 3000 (9'10") 3100 (10'1") 3261 (10'8")
M: Turning radius at bucket corner mm (ft.in) 2015 (6'7") 2016 (6'7") 2150 (7') 1998 (6'7")
N: Turning radius at rear tail corner mm (ft.in) 1665 (5'5") 1667 (5'6") 1650 (5'5") 1998 (6'7")
P: Tilt back angle, carry position degree 30 30 33 28.6
Q: Dump angle, max. height degree 45 45 41 40.4
*: Narrow version
7-4
CONTENTS
SECTION 8
INDEX
SECTION 8A
MOBILE CRUSHERS
& RECYCLERS
CONTENTS
Benefits ..................................................................... 8A-2
Features .................................................................... 8A-3
Type of crushers/recyclers ...................................... 8A-4
Model and application ............................................. 8A-5
Specifications ........................................................... 8A-6
Dimensions ............................................................... 8A-8
Productivity ............................................................ 8A-10
8A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Hydraulic excavator
Machine-mounted type
magnetic separator
Undersized
material
Oversized
material
Vibrating screen
Wheel loader
Truck
8A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
8A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
The jaw crusher can crush large blocks and is suitable for crushing concrete debris and natural stone. It has
a swing jaw plate and fixed jaw plate. Those jaw plates crunch material.
The impact crusher is used for secondary crushing and granulation of asphalt, concrete debris, and natural
stone. It produces round grains in many cases and is suitable for production of relatively fine grains. The
blocks put in the impact crusher are thrown in the tangential direction by the blow bar of the rotor which is
rotating at high speed and are crushed by collision with the impact plate. They are also crushed by collision
with each other.
The shear shreds industrial waste as well as bulky domestic refuse to reduce its volume, thereby contributing
to extending the service life of disposal sites.
[JAW CRUSHER]
Material to be crushed Swing
Vibratory grizzly jaw plate
Feed-in bar(2 stage)
hopper Fixed Crusher Primary belt conveyor
jaw plate motor Magnetic separator motor
Vibratory grizzly
feeder
Vibrator
Primary Primary
belt conveyor belt conveyor FKZ00163E
lift cylinder Muck
removing chute
[IMPACT CRUSHER]
Material to be crushed
Grizzly bars(2 stage) Impact plates
Hopper
Magnetic separator (Optional)
Vibratory grizzly
feeder
Vibrator Primary belt conveyor
M-type chute
Blow bar
Rotor FVZM0560E
Piece cutters
(monolithic cutters)
FZBH0289
Dual-axis shear
8A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
CRUSHER OUTPUT
mm
CRUSHING CAPACITY ton/h N.A. N.A.
* Concrete debris : MOST SUITABLE : SUITABLE
** Andesite
8A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
8A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
* Estimated value
** Including conveyor
8A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
C B
G
N F
M
L D E
K A
J
Unit: mm (ft.in)
BR100JG-2 BR210JG-1 BR380JG-1 BR550JG-1 BR1600JG-1
8070 (26'6") 9800 (32'2") 12500 (41'0") 13430 (44'1") 18500 (60'8")
A
*8070 (26'6") *9800 (32'2") *12500 (41'0") *13430 (44'1") —
2700 (8'10") 2890 (9'6") 3200 (10'6") 3640 (11'11") —
B
*2515 (8'3") *2890 (9'6") *3200 (10'6") *3395 (11'2") —
C 2515 (8'3") 2700 (8'10") 3200 (10'6") 3640 (11'11") 7755 (25'5")
D 2115 (6'11") 2750 (9') 3275 (10'9") 3700 (12'2") 4995 (16'5")
E 3795 (12'5") 4630 (15'2") 6080 (20'0") 6145 (20'2") —
F 205 (8") 250 (9.8") 300 (12") 350 (1'2") 560 (1'10")
G 1500 (4'11") 1995 (6'7") 2800 (9'2") 3000 (9'10") 3050 (10')
H 2165 (7'1") 2830 (9'4") 3700 (12'2") 4365 (14'4") —
I 1840 (6') 2220 (7'3") 2500 (8'2") 2805 (9'2") 3720 (12'2")
2345 (7'8") 2700 (8'10") — 3115 (10'3") 5470 (17'11")
J
*2200 (7'3") *2700 (8'10") — *2995 (9'10") —
K 2100 (6'11") 2500 (8'3") 2815 (9'3") 2980 (9'9") 4600 (15'1")
L 1700 (5'7") 2000 (6'7") 2280 (7'6") 2480 (8'2") 3900 (12'10")
M 600 (24") 600 (24") 1050 (41.3") 1050 (41.3") 1400 (55.1")
N 400 (16") 500 (20") 500 (20") 500 (20") 700 (28")
* at transportation
H
I M J
B
C G
N F D E
L A
K
Unit: mm (ft.in)
BR100RG-1 BR250RG-1 BR480RG-1
5850 (19'2") 11100 (36'5") 14250 (46'9")
A
*5850 (19'2") *11100 (36'5") *14250 (46'9")
2455 (8'1") 3150 (10'4") 4120 (13'6")
B
*2455 (8'1") *3150 (10'4") *3496 (11'6")
C 2410 (7'11") 3150 (10'4") 3470 (11'5")
D 2130 (7') 3440 (11'3") 3655 (12')
E 2315 (7'7") 5660 (18'7") 6530 (21'5")
F 205 (8") 219 (8'6") 285 (11")
G 700 (2'4") 2040 (6'8") 3000 (9'10")
H 1370 (4'6") 3230 (10'7") 4390 (14'5")
I 1625 (5'4") 2340 (7'8") 2990 (9'10")
2200 (7'3") 2810 (9'3") 2995 (9'10")
J
*2200 (7'3") *2810 (9'3") *2995 (9'10")
K 2150 (7'1") 2780 (9'1") 2960 (9'9")
L 1700 (5'7") 2280 (7'6") 2460 (8'1")
M 600 (24") 900 (35.4") 1200 (47.2")
N 450 (18") 500 (20") 500 (20")
* at transportation
8A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Unit: mm (ft.in)
BR200S-1 BR300S-1
6870 (22'6") 8650 (28'5")
A
*6870 (22'6") *8650 (28'5")
3290 (10'10") 3880 (12'9")*
B
*2940 (9'8") *3160 (10'4")
C 2536 (8'4") 3020 (9'11")
D 2750 (9') 3260 (10'8")
E 2250 (7'5") 2920 (9'7")
F 3050 (10') 4000 (13'1")
G 980 (3'3") 905 (3")
H 2360 (7'9") 2760 (9'1")
I 2400 (7'10") 2720 (8'11")
2825 (9'3") 3295 (10'10")
J
*2780 (9'1") *2997 (9'10")
K 2780 (9'1") 2780 (9'1")
L 2280 (7'6") 2280 (7'6")
M 900 (35") 900 (35")
N 500 (20") 500 (20")
* at transportation
8A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
* When recommending production capacity, confirm the properties of the rock samples from the customer's quarry by
crushing them actually.
* Basically, the production capacity and size of produced grains are decided by the quantity, size, and hardness of the
material, clearance between the blow bar and impact plate, and rotor speed. Since the production capacity is in inverse
proportion to the size of the produced grains, adjust the changeable elements of the machine, feed rate, rotor speed,
clearance between the blow bar and impact plate, etc., according to the type of the material and the grain size required by
the customer. Then, use a proper screen and put oversized material again.
* For the rough standard of the production capacity, see the catalogs and sales material for the mobile crusher.
* If the production capacity of a mobile crusher in a customer's jobsite is necessary, ask Komatsu.
8A-10
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 8B
MOBILE WOOD
TUB GRINDERS
CONTENTS
Features .................................................................... 8B-2
Specifications ........................................................... 8B-3
Dimensions ............................................................... 8B-4
8B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Inclined cover
Screen
Movable tub
Grind mill
Discharge conveyor belt
Magnetic
separator
(option)
8B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
* Including conveyor
8B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
B
F
G.L E
I J
H D
G A
Unit: mm (ft.in)
BR120T-1 BR200T-1
8520 (27'11") 12850 (42'2")
A
*8330 (27'4") *9975 (32'9")
2950 (9'8") 3980 (13'1")
B
*2710 (8'11") *3100 (10'2")
2790 (9'2") 3570 (11'9")
C
*2440 (8') *3000 (9'10")
D 2235 (7'4") 2750 (9')
E 250 (10") 250 (10")
F 2575 (8'5") 3090 (10'2")
G 2290 (7'6") 2880 (9'5")
H 1840 (6'1") 2380 (7'10")
I 700 (28") 900 (35.4")
J 450 (18") 500 (20")
* at transportation
8B-4
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 8C
MOBILE SOIL
RECYCLERS
CONTENTS
Features .................................................................... 8C-2
Specifications ........................................................... 8C-3
Dimensions ............................................................... 8C-4
8C-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
8C-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Model BZ210
Item
OPERATING WEIGHT kg (lb) 20500 (45,190)
FLYWHEEL HORSEPOWER HP (kW)/RPM 144 (107)/1950
MIXER PERFORMANCE:
Processing capacity m3/h (cu.yd/h) 40 - 150 (52 -195)
Mixing method Soil cutter and triple rotary hammer
Row material soil hopper volume m (cu.yd)
3 2.0 (2.4)
Max. material size mm (in) 200 (7'9")
Solidifying material hopper capacity m3 (cu.yd) 3.0 (3.9)
Solidifying material feed adjustment range kg/m3 (lb/cu.yd) 9 - 400 (15 - 674)
ENGINE: KOMATSU
Model SAA6D102E
No. of cylinder- bore × stroke mm 6-102 × 120
(in) (4.02 × 4.72)
Piston displacement ltr. (cu.in) 5.88 (359)
DIMENSIONS:
Overall length* 13210 (43'4")
Overall height (transport) 4560 (15'0")
mm (ft.in)
Overall width (transport) 2850 (9'4')
Length of track on ground 2750 (9')
Track gauge 2350 (7'9')
CAPACITY:
Fuel tank ltr. (U.S. Gal) 400 (107)
Hydraulic tank 240 (63)
* Including conveyer
8C-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
2700(8'10")
)
3510(11'6")
)
(
(
2900((9'6")
4560(15')
)
4385(14'5")
(During transport)
(During transport)
3100(10'2"))
(
3250(10'8"))
2450(8')
( )
(
(
1600(5'3")
( )
(Under the rubber chute)
Ground clearance
c
300(1') 6860(22'6")
( )
900(2'11
900(2'11")
0 13210(43'4")
( )
500(20")
2350(7'9")
( )
2850(9'4")
( )
(Durring trasport) FVBH0225
8C-4
CONTENTS
SECTION 9
INDEX
SECTION 9A
ROUGH TERRAIN
CRANES
CONTENTS
Features .................................................................... 9A-2
Specifications ........................................................... 9A-6
Dimensions ............................................................... 9A-9
Total Rated Loads:
LW100-1 .............................................................. 9A-10
LW250-5 .............................................................. 9A-13
LW500-1 .............................................................. 9A-17
Working Radius vs. Lifting Height ........................ 9A-21
9A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
LW100-1
• Greater working range with compact style
This new generation compact style provides a
working range that is higher and has greater
reach, resulting in a more capable machine. With
maximum lift heights of 26.8 m (87'11") (jib) and
23.0m (75'6") (boom) and work radius of 24.3 m
(79'9") (jib) and 20.3 m (66'7") (boom), lifting work
can be carried out stable with a highly rigid six-
section boom whose new design minimizes slack.
• New equipment, slides, and three-stage
tilt jib
A jib that boasts a length of 3.4 m (11'2") housed
in a highly rigid, six-section 21.5 m (70'6") boom
that is compact and yet offers outstanding work
capabilities, and a sliding system makes
deployment and retraction of the jib extremely Tilt jib can be set at three different angles
easy.
• Separate hook function
When the jib is extended 0.7 m (2'4"), the cable of the main hook is prevented from becoming entangled
with the cable of the auxiliary hook, which facilitates smoother and safer operation.
• Flat nose gives the feel of a car
This configuration results in a flat nose in which the boom tip does not stick out from the front of the
chassis, giving the operator the impression that he is at the wheel of a car during both driving and parking.
• Smallest rear swing radius in its class
The outrigger on the lifting side can be extended
greatly to allow for safer and easier operation in
tight work places. 3.38m(11'1")
Rear swing radius: 1.35 m (4'5")
Front swing radius: 1.43 m (4'8")
• Slim enough to fit into the tightest of 4.7m
(15'5
spots ")
The minimum right-angle road width is only 3.38 3.38m
m (11'1") which is also the narrowest in the class. (11'1") FVBH0076
9A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
LW100-1
• Our powerful air-conditioning system
offers a comfortable interior
This equipment has a highly effective air
conditioning system with a high capacity
dehumidifying function.
FVBH0078
9A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
LW250-5
• Newly equipped with a high rigidity five-section boom
This newly designed five-section boom has high rigidity. Higher lifting operations over a wider range can
be performed with minimal deflection and good stability.
• Maximum boom length: 32.0 m (105')
• Maximum lift height jib: 47.7 m (156'6")
• Maximum total rated load: 26 ton × 3.0m (27.7U.S ton × 9'10")
• Short nose with five-section boom
The LW250 is equipped with a short five-section
boom, leading to the achievement of a short
nose. Compared to conventional 25 ton class 4.5m(14'9")
machines, the boom overhang can be made
about 2 meters shorter, making the overall length
of the vehicle very compact.
7.2m
(23'7
• Smallest tail swing radius and front ")
swing radius in its class 5.4m
(17'9")
Compact design in all areas of the equipment FVBH0074
makes the overall size compact.
• Rear swing radius: 2.95 m (9'8")
• Front swing radius: 2.0 m (6'7")
• Four-mode steering allows for tight turns
The steering system, which fully shows the ability
for the short nose to enter narrow spaces, has
four modes: front 2 wheel steering, rear 2 wheel
steering, club steering and 4 wheel steering.
The LW250 is also equipped with a reverse
steering compensation function, which can be
easily operated from within the cab.
• Low noise level is gentle to the surrounding area
For rough terrain cranes, which often have to operate in cities in the depth of night, it is vital to keep the
operating noise level down. Our equipment has been designed to take into consideration the surrounding
environment.
[76 dB (A) at 7 m (23')]
• Most spacious cab in its class
With the LW250, there's plenty of room in the 930 mm width interior, which is the most spacious in the 25
ton class. The advance cockpit has a well designed layout making instruments easy to read, and the high
quality, sophisticated interior design gives a relaxed feeling like that of a passenger car with plenty of room
to stretch your legs.
• Our powerful air conditioning system
offers a comfortable interior
This equipment has a highly effective air
conditioning system with a high capacity
dehumidifying function.
9A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
FVBH0034
Air-over-hydraulic
four-wheel disc brakes
• New body style with less vibration
Our significantly shorter nose with the five-section boom and a long wheel base reduce travel pitch. The
standard-equipped tires are high load 385/95R25 radials with good road surface gripping properties and
good travel stability.
• Viscous mount allows for reduced cab
vibration
For the cab mount, we've chosen a viscous
mount using rubber and silicone.
This effectively absorbs chassis vibration,
reducing cab vibration.
Viscous mount
9A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Model
Item LW100-1 LW250-5
CRANE PERFORMANCE:
Maximum rated load* kg × m 4.1 m boom 10000 × 2.5 7.6 m boom 26000 × 3.0
(lb × ft.in) (13'5") (22,050 × 8'2") (24'11") (57,320 × 9'10")
7.6 m boom 5000 × 4.5 13.7 m boom 21000 × 3.5
(24'11") (11,020 × 14'9") (44'11") (46,300 × 11'6")
11.1 m boom 5000 × 4.0 19.8 m boom 14500 × 4.5
(36'5") (11,020 × 13'1") (65') (31,970 × 14'9")
14.5 m boom 4000 × 4.5 25.9 m boom 10600 × 5.5
(47'7") (8,820 × 14'9") (85') (23,370 × 18'1")
18.0 m boom 4000×4.0 30.5 m boom 7000 × 8.0
(59'1") (8,820×13'1") (100') (15,430 × 26'3")
21.5 m boom 2300×6.0 32.0 m boom 5900 × 8.0
(70'6") (5,070 × 19'8") (105') (13,010 × 26'3")
21.5 + 0.7 m jib 1400 × 8.0 30.5 + 7.4 m jib 3000 × (70°)
(70'6" + 2'4") (3,090 × 19'8") (100' + 24'3") (6,610)
21.5 + 3.4 m jib 1200 × (70°) 30.5 + 12.6 m jib 2000 × (75°)
(70'6" + 11'2") (2,650) (100' + 41'4") (4,410)
1400 × 8.0 32.0 + 7.4 m jib 2600 × (72°)
Single top
(3,090 × 19'8") (105' + 24'3") (5,730)
1200 32.0 + 12.6 m jib 1700 × (75°)
Jib
(2,650) (105' + 41'4") (3,750)
3000
Single top
(6,610)
Boom length m (ft.in) 4.1~21.5 (13'5"~70'6") 7.6~32.0 (24'11"~105')
Jib length m (ft.in) 4.0 m (13'1") 7.4 (24'3")/12.6 (41'4")
Maximum lifting height
m (ft.in) 23.0 (75'6")/26.8 (87'11") 35.3 (115'10")/47.7 (156'6")
Boom/jib
Maximum working radius m (ft.in) 20.3 (66'7")/24.3(79'9") 29.0 (95'2")/35.0 (114'10")
Boom/jib
Wire line speed m (ft.in)/ Hi 117 (383'11")/108 (354'4") Hi Lo
Main winch/Aux. winch min Lo 62 (203'5")/57 (187') 130 (426'6")/65 (213'3")
Boom telescoping time sec 59 (4.1 m~21.5 m) 75 (7.6 m~32 m)
Boom hoisting time sec 31 (-13°~83°) 45 (0~83)
Swing speed RPM 2.3 2.5
Item
Model LW100-1 LW250-5
WIRE ROPE: IWRC 6xWS (29) 7x7+6xFi (29)
Z-stranded, twist resistant, Class B ordinary Z-stranded, twist
10 mm (0.39") × 120 m (393'9") resistant, 16 mm (0.63") × 170 m
(557'9")
MAJOR CRANE 6-stage box-section type (boom) 5-stage box-section type
MECHANISM: 1-stage type of box frame structure 2-stage type of box frame structure
Main boom type (offset angle 0°, 20°40°) (offset angle 5°~60°)
Jib type Driven by 2 hydraulic motors, 2 shafts 2 hydraulic motors driven 2 drums with
Winch 2 drums with free fall free fall
9A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Model
LW500-1
Item
CRANE PERFORMANCE:
Maximum rated load* kg x m 9.5m boom 50000x3.0
(lb x ft.in) (31'2") (110,250x9'10")
16.4m boom 30000x4.5
(53'10") (66,150x14'9")
23.1m boom 20000x5.0
(75'9") (44,100x16'5")
29.7m boom 12,000x8.0
(97'5") (26,460x26'3")
36.3m boom 11,000x7.0
(119'1") (24,250x23')
43.0m boom 7,000x10.0
(141'1") (15,430x32'10")
7.4m jib 3,500x(74°)
(24'3") (7,710)
12.6m jib 2,500x(77°)
(41'4") (5,510)
4500
Single top
(9,920)
Boom length m (ft.in) 9.8~43 (32'2"~141'1")
Jib length m (ft.in) 7.4(24'3")/12.6(41'4")
Maximum lifting height
m (ft.in) 43.8 (143'8")/56.6 (185'8")
Boom/jib
Maximum working radius
m (ft.in) 34.0(111'7")/40.0(131'3")
Boom/jib
Wire line speed Hi 130 (426'6")/119 (390'5")
m (ft.in)/min
Main winch/Aux. winch Lo 65 (213'3")/59.5 (195'3")
Boom telescoping time sec 115 (9.8m~43.0m)(32'2"~141'1")
Boom hoisting time sec 60 (0°~83°)
Swing speed RPM 2.6
* With outriggers fully extended
Item
LW500-1
Model
WIRE ROPE: IWRC 6xFi (29)
de-Twist-ability,
Main 18mm(0'59")x232m(761'2")
MAJOR CRANE MECHANISM: Hexagonal 6-stage box-section type
Main boom type Box structure 2-stage type
Jib type Hydraulic 2 motors drive 2 drums,
Winch With free fall
9A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Item
Model LW100-1 LW250-5 LW500-1
GROSS VEHICLE kg (lb) 12950 (28,550) 26980 (59,480) 37990 (83,760)
WEIGHT *(H)(X)
FLYWHEEL HP (kW)/ 158 (118)/3000 246.5 (184)/2100 350 (261)/2100
RPM
TRAVEL
PERFORMANCE:
Maximum speed km/h (MPH) 55 (34.2) 55 (34.2) 49 (30.4)
Grade-ability (tan θ) 0.52 0.6 0.6
Turning radius:
4-wheel steering m (ft.in) 3.95 (13') 5.4 (17'9") 6.1 (20')
2-wheel steering 7.11 (23'4") 9.3 (30'6") 10.6 (34'9")
DIMENSIONS:
Overall length 6235 (20'5") 9940 (32'7") 11940 (39'2")
Overall width 2000 (6'7") 2620 (8'7") 2980 (9'9")
Overall height mm (ft.in) 2800 (9'2") 3520 (11'7") 3660 (12')
Wheelbase 2800 (9'2") 3750 (12'4") 4950 (16'3")
Treads (front and rear) 1680 (5'6") 2190 (7'2") 2400 (7'10")
Tail swing radius 1350 (4'5") 2950 (9'8") 3550 (11'8")
ENGINE: KOMATSU KOMATSU KOMATSU
Model SAA6D95LE S6D125E S6D140E
No. of cylinders- mm (in) 6-95 × 115 6-125 × 150 6-140x165
bore × stroke (3.7 × 4.5) (4.92 × 5.91) (5.51x6.50)
Piston displacement ltr. (cu.in) 4.89 (298) 11.04 (674) 15.2 (928)
POWER TRAIN:
Drive method 2-wheel drive/4-wheel 2-wheel drive/4-wheel 2-wheel drive/4-wheel
Transmission type drive drive drive
Electronic control fully Electronic control fully Electronic control fully
Number of speeds:
Forward/reverse 4/2 3/1 (with Hi & Lo) 3/1 (with Hi & Lo)
TIRES:
Front tire 11R22.5-16PR 385/95R25 505/95R25
Rear tire 11R22.5-16PR 385/95R25 505/95R25
CAPACITY:
Fuel tank ltr. (U.S. Gal) 200 (52.8) 300 (79.3) 300 (79.3)
* (X) : X-shaped outrigger
(H) : H-shaped outrigger
9A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
B
C J
D E F
G
A
H FVBH0079
A B C D E F G H I J (Max.)
6235 2800 2000 1730 2800 1705 1730 4760* 1350 4750
(20'5") (9'2") (6'7") (5'8") (9'2") (5'7") (5'8") (15'7") (4'5") (15'7")
LW100-1
4780**
(15'8")
9940 3520 2620 1905 3750 2135 4055 6600 2950 6600
LW250-5
(32'7") (11'7") (8'7") (6'3") (12'4") (7') (13'4") (21'8") (9'8") (21'8")
11940 3660 2980 1915 4950 2385 7900 3550 7500
LW500-1 —
(39'2") (12') (9'9") (6'3") (16'3") (7'10") (25'11") (11'8") (24'7")
* X-shaped outrigger
** H-shaped outrigger
9A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
LW100-1
When outriggers are used (Boom working) (unit: ton)
Outrigger maximum extended width 4.75 m (360°) Outrigger intermediate extended width 4.10 m (Over side)
Boom Boom
length (m) length (m)
4.1 7.6 11.1 14.5 18.0 21.5 4.1 7.6 11.1 14.5 18.0 21.5
Working Working
radius (m) radius (m)
1.0 10.00 5.00 1.0 10.00 5.00
1.5 10.00 5.00 5.00 1.5 10.00 5.00 5.00
2.0 10.00 5.00 5.00 4.00 2.0 10.00 5.00 5.00 4.00
2.5 10.00 5.00 5.00 4.00 4.00 2.5 9.40 5.00 5.00 4.00 4.00
3.0 8.00 5.00 5.00 4.00 4.00 2.30 3.0 8.00 5.00 5.00 4.00 4.00 2.30
3.5 5.00 5.00 4.00 4.00 2.30 3.5 5.00 5.00 4.00 4.00 2.30
4.0 5.00 5.00 4.00 4.00 2.30 4.0 5.00 5.00 4.00 4.00 2.30
4.5 5.00 4.55 4.00 3.70 2.30 4.5 4.95 4.55 4.00 3.70 2.30
5.0 4.60 4.10 3.70 3.40 2.30 5.0 4.32 4.10 3.70 3.40 2.30
5.5 4.15 3.50 3.40 3.10 2.30 5.5 3.85 3.50 3.40 3.10 2.30
6.0 3.70 3.15 3.15 2.85 2.30 6.0 3.40 3.15 3.15 2.85 2.30
6.5 3.35(6.4m) 2.95 2.90 2.60 2.15 6.5 3.10(6.4m) 2.90 2.90 2.60 2.15
7.0 2.80 2.65 2.40 2.00 7.0 2.49 2.65 2.40 2.00
8.0 2.30 2.25 2.05 1.75 8.0 1.89 2.10 2.05 1.75
9.0 1.90 1.95 1.80 1.55 9.0 1.46 1.67 1.79 1.55
10.0 1.57(9.9m) 1.70 1.60 1.40 10.0 1.16(9.9m) 1.34 1.46 1.40
11.0 1.45 1.40 1.25 11.0 1.08 1.20 1.25
12.0 1.20 1.25 1.15 12.0 0.85 0.99 1.07
13.0 1.05 1.05 1.05 13.0 0.66 0.80 0.90
14.0 0.92(13.4m) 0.90 0.95 14.0 0.60(13.4m) 0.64 0.74
15.0 0.79 0.85 15.0 0.50 0.59
16.0 0.65 0.73 16.0 0.38 0.47
17.0 0.56(16.8m) 0.60 17.0 0.30(16.8m) 0.36
18.0 0.50 18.0 0.27
19.0 0.42 19.0 0.20
20.0 0.35 20.0
21.0 0.33(20.3m) 21.0
Dangerous Dangerous
angle — — — — — — angle — — — — — 24°
Outrigger intermediate extended width 3.40 m (Over side) Outrigger intermediate extended width 2.80 m (Over side)
Boom Boom
length (m) length (m)
4.1 7.6 11.1 14.5 18.0 21.5 4.1 7.6 11.1 14.5 18.0 21.5
Working Working
radius (m) radius (m)
1.0 10.00 5.00 1.0 10.00 5.00
1.5 10.00 5.00 5.00 1.5 10.00 5.00 5.00
2.0 10.00 5.00 5.00 4.00 2.0 9.60 5.00 5.00 4.00
2.5 8.60 5.00 5.00 4.00 4.00 2.5 7.80 5.00 5.00 4.00 4.00
3.0 7.30 5.00 5.00 4.00 4.00 2.30 3.0 6.60 5.00 5.00 4.00 4.00 2.30
3.5 5.00 5.00 4.00 4.00 2.30 3.5 5.00 4.93 4.00 4.00 2.30
4.0 5.00 5.00 4.00 4.00 2.30 4.0 3.90 3.77 4.00 4.00 2.30
4.5 4.40 4.26 4.00 3.70 2.30 4.5 3.10 2.98 3.24 3.39 2.30
5.0 3.57 3.45 3.70 3.40 2.30 5.0 2.52 2.42 2.65 2.80 2.30
5.5 2.96 2.85 3.10 3.10 2.30 5.5 2.09 1.98 2.22 2.35 2.30
6.0 2.50 2.40 2.63 2.76 2.30 6.0 1.75 1.65 1.87 2.00 2.08
6.5 2.20(6.4m) 2.02 2.25 2.39 2.15 6.5 1.53(6.4m) 1.38 1.59 1.72 1.80
7.0 1.73 1.95 2.08 2.00 7.0 1.15 1.36 1.49 1.57
8.0 1.28 1.49 1.61 1.69 8.0 0.75 1.01 1.13 1.21
9.0 0.90 1.15 1.27 1.35 9.0 0.44 0.70 0.85 0.94
10.0 0.65(9.9m) 0.88 1.01 1.09 10.0 0.23(9.9m) 0.46 0.61 0.72
11.0 0.64 0.80 0.89 11.0 0.27 0.42 0.52
12.0 0.45 0.60 0.70 12.0 0.20(11.4m) 0.27 0.36
13.0 0.30 0.44 0.54 13.0 0.20(12.5m) 0.24
14.0 0.24(13.4m) 0.30 0.40 14.0 0.20(13.3m)
15.0 0.20(14.9m) 0.29 15.0
16.0 0.20(15.9m) 16.0
17.0 17.0
18.0 18.0
Dangerous Dangerous
angle — — — — 30° 41° angle — — — 34° 44° 51°
Please read the "Precautions when using outrigger" section when working at maximum rated load during single top work or when
working at 1-step extension jib (jib length 0.7 m).
9A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
LW100-1
When outriggers are used (Boom working ) (Unit : ton)
Outrigger minimum extended width 1.65 m (Over side),
Outrigger intermediate extended width 2.20 m (Over side)
H-shape only
Boom Boom
length (m) length (m)
4.1 7.6 11.1 14.5 18.0 21.5 4.1 7.6 11.1 14.5 18.0 21.5
Working Working
radius (m) radius (m)
1.0 10.00 5.00 1.0 10.00 5.00
1.5 7.90 5.00 5.00 1.5 7.90 5.00 5.00
2.0 6.25 5.00 5.00 4.00 2.0 6.20 5.00 5.00 4.00
2.5 5.00 4.75 4.68 4.00 4.00 2.5 4.20 3.90 3.77 4.00 4.00
3.0 4.10 3.87 3.78 4.00 4.00 2.30 3.0 3.05 2.75 2.65 2.90 3.05 2.30
3.5 3.18 3.09 3.32 3.45 2.30 3.5 2.05 1.95 2.17 2.31 2.30
4.0 2.56 2.45 2.70 2.84 2.30 4.0 1.56 1.46 1.68 1.81 1.90
4.5 2.03 1.93 2.15 2.30 2.30 4.5 1.20 1.10 1.32 1.45 1.53
5.0 1.64 1.54 1.76 1.89 1.97 5.0 0.90 0.77 1.05 1.17 1.25
5.5 1.33 1.23 1.45 1.57 1.66 5.5 0.65 0.52 0.80 0.95 1.03
6.0 1.09 0.97 1.20 1.32 1.40 6.0 0.45 0.32 0.58 0.74 0.85
6.5 0.90(6.4m) 0.73 1.00 1.12 1.20 6.5 0.31(6.4m) 0.20(6.3m) 0.41 0.57 0.67
7.0 0.53 0.80 0.95 1.03 7.0 0.27 0.42 0.53
8.0 0.22 0.48 0.64 0.74 8.0 0.20(7.2m) 0.20(7.9m) 0.29
9.0 0.25 0.40 0.50 9.0 0.20(8.5m)
10.0 0.20(9.2m) 0.22 0.32 10.0
11.0 0.20(10.1m) 0.20(10.8m) 11.0
12.0 12.0
13.0 13.0
14.0 14.0
15.0 15.0
16.0 16.0
17.0 17.0
18.0 18.0
Dangerous Dangerous
angle
— — 39° 48° 55° 59° angle
— — 52° 59° 63° 66°
Outrigger maximum extended width 4.75 m (360°) Outrigger intermediate extended width 4.10 m (Over side)
Jib Tilt Angle Jib Tilt Angle
Boom angle (°) Boom angle (°)
0° 20° 40° 0° 20° 40°
83.0 1.20 0.89 0.58 83.0 1.20 0.89 0.58
80.0 1.20 0.89 0.58 80.0 1.20 0.89 0.58
75.0 1.20 0.77 0.54 75.0 1.20 0.77 0.54
72.0 1.20 0.72 0.52 72.0 1.20 0.72 0.52
70.0 1.15 0.69 0.51 70.0 1.15 0.69 0.51
65.0 0.95 0.62 0.48 65.0 0.95 0.62 0.48
60.0 0.82 0.57 0.47 60.0 0.82 0.57 0.47
55.0 0.71 0.53 0.45 55.0 0.71 0.53 0.45
50.0 0.64 0.50 0.44 50.0 0.58 0.50 0.44
45.0 0.55 0.48 0.44 45.0 0.43 0.40 0.40
40.0 0.47 0.43 0.43 40.0 0.32 0.30 0.30
35.0 0.40 0.38 35.0 0.23 0.22
30.0 0.35 0.33 30.0
25.0 0.29 0.28 25.0
20.0 0.25 0.24 20.0
15.0 0.22 15.0
10.0 0.20 10.0
Dangerous angle — 20° 40° Dangerous angle 33° 34° 40°
9A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
LW100-1
When outriggers are used (21.5 m Boom + 3.4 m Auxiliary jib working) (Unit : ton)
Outrigger intermediate extended width 3.40 m (Over side) Outrigger intermediate extended width 2.80 m (Over side)
Jib Tilt Angle Jib Tilt Angle
Boom angle (°) Boom angle (°)
0° 20° 40° 0° 20° 40°
83.0 1.20 0.89 0.58 83.0 1.20 0.89 0.58
80.0 1.20 0.89 0.58 80.0 1.20 0.89 0.58
75.0 1.20 0.77 0.54 75.0 1.20 0.77 0.54
72.0 1.20 0.72 0.52 72.0 1.20 0.72 0.52
70.0 1.15 0.69 0.51 70.0 1.04 0.69 0.51
65.0 0.95 0.62 0.48 65.0 0.68 0.60 0.48
60.0 0.70 0.57 0.47 60.0 0.42 0.37 0.35
55.0 0.48 0.43 0.42 55.0 0.23 0.20
50.0 0.31 0.29 0.28 50.0
45.0 45.0
Dangerous Dangerous
46° 46° 47° 54° 55° 56°
angle angle
9A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
LW100-1
When outriggers are used
Suspension lock (option) mounted vehicles only (unit : ton)
Hoisling/traveling (Max. speed 2 km/h)
Boom Forward Boom 360°
length (m) length (m)
Working 4.1 7.6 11.1 Working 4.1 7.6 11.0
radius (m) radius (m)
1.0 4.90 4.90 1.0 3.40 3.20
1.5 4.25 4.10 4.05 1.5 3.30 3.05 3.00
2.0 3.45 3.30 3.25 2.0 2.40 2.15 2.05
2.5 2.90 2.70 2.65 2.5 1.80 1.55 1.45
3.0 2.45 2.25 2.20 3.0 1.35 1.05 1.00
3.5 1.85 1.80 3.5 0.75 0.65
4.0 1.55 1.50 4.0 0.50 0.40
4.5 1.30 1.25 4.5 0.25 0.20 (4.4 m)
5.0 1.10 1.00 5.0
5.5 0.90 0.85 5.5
6.0 0.75 0.70 6.0
6.5 0.65 (6.4 m) 0.55 6.5
7.0 0.40 7.0
8.0 0.20 (7.8 m) 8.0
Dangerous Dangerous
— — 39° — 46° 64°
angle angle
LW250-5
When outriggers are used (Boom working) (unit: ton)
Outrigger maximum extended width 6.6 m (360°) Outrigger intermediate extended width 5.9 m (Over side)
Boom Boom
length length
(m) (m)
7.1 13.7 19.8 25.9 30.5 32.0 7.6 13.7 19.8 25.9 30.5 32.0
Working Working
radius radius
(m) (m)
2.5 26.00 21.00 14.50 2.5 26.00 21.00 14.50
3.0 26.00 21.00 14.50 10.60 3.0 26.00 21.00 14.50 10.60
3.5 25.40 21.00 14.50 10.60 7.00 3.5 25.40 21.00 14.50 10.60 7.00
4.0 23.40 20.00 14.50 10.60 7.00 5.90 4.0 23.40 20.00 14.50 10.60 7.00 5.90
4.5 21.40 18.90 14.50 10.60 7.00 5.90 4.5 21.40 18.90 14.50 10.60 7.00 5.90
5.0 18.10 17.60 14.40 10.60 7.00 5.90 5.0 18.10 17.60 14.40 10.60 7.00 5.90
5.5 16.50 13.80 10.60 7.00 5.90 5.5 16.50 13.80 10.60 7.00 5.90
6.0 15.30 13.00 10.40 7.00 5.90 6.0 15.30 13.00 10.40 7.00 5.90
6.5 14.20 12.30 9.80 7.00 5.90 6.5 13.10 12.30 9.80 7.00 5.90
7.0 13.00 11.60 9.25 7.00 5.90 7.0 11.20 11.60 9.25 7.00 5.90
8.0 10.00 10.00 8.25 7.00 5.90 8.0 8.45 9.35 8.25 7.00 5.90
9.0 7.90 8.70 7.45 6.30 5.50 9.0 6.65 7.45 7.45 6.30 5.50
10.0 6.45 7.20 6.75 5.80 5.10 10.0 5.35 6.10 6.50 5.80 5.10
11.0 5.30 6.10 6.05 5.30 4.70 11.0 4.40 5.10 5.50 5.30 4.70
12.0 5.20 5.50 4.90 4.30 12.0 4.30 4.70 4.85 4.35
13.0 4.45 4.70 4.50 4.00 13.0 3.70 4.05 4.20 4.00
14.0 3.80 4.10 4.15 3.65 14.0 3.20 3.50 3.70 3.65
15.0 3.20 3.70 3.80 3.35 15.0 2.75 3.10 3.25 3.30
16.0 2.85 3.25 3.45 3.10 16.0 2.40 2.70 2.85 2.90
17.0 2.50 2.90 3.05 2.90 17.0 2.10 2.40 2.55 2.60
18.0 2.55 2.70 2.70 18.0 2.10 2.25 2.30
19.0 2.55 2.45 2.50 19.0 1.85 2.00 2.05
20.0 2.00 2.20 2.25 20.0 1.65 1.80 1.85
22.0 1.55 1.75 1.80 22.0 1.20 1.40 1.45
24.0 1.40 1.45 24.0 1.00 1.10
26.0 1.15 1.15 26.0 0.75 0.75
28.0 0.95 28.0 0.55
29.0 0.75 29.0
Dangerous angle — — — — — Dangerous angle — — — — 10°
9A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
LW250-5
When outriggers are not used (Boom working) (unit: ton)
Outrigger intermediate extended width 3.8 m (Over side) Outrigger minimum extended width 2.2 m (Over side), H-Shape
Boom Boom
length (m) length (m)
7.1 13.7 19.8 25.9 30.5 32.0 7.6 13.7 19.8 25.9 30.5 32.0
Working Working
radius (m) radius (m)
2.5 26.00 21.00 14.50 2.5 13.00 12.00 11.00
3.0 26.00 21.00 14.50 10.60 3.0 12.50 11.70 11.00 8.30
3.5 22.50 20.00 14.50 10.60 7.00 3.5 9.55 9.10 9.50 8.30 5.50
4.0 17.50 16.65 14.50 10.60 7.00 5.90 4.0 7.70 7.10 7.50 7.30 5.50 4.30
4.5 13.70 12.95 13.50 10.60 7.00 5.90 4.5 6.25 5.65 6.10 6.30 5.50 4.30
5.0 10.90 10.45 11.10 10.60 7.00 5.90 5.0 5.00 4.60 5.10 5.45 5.50 4.30
5.5 8.65 9.40 9.65 7.00 5.90 5.5 3.80 4.30 4.65 4.75 4.30
6.0 7.30 8.05 8.30 7.00 5.90 6.0 3.15 3.70 4.00 4.15 4.30
6.5 6.20 7.00 7.20 7.00 5.90 6.5 2.60 3.10 3.50 3.65 3.70
7.0 5.35 6.10 6.45 6.60 5.90 7.0 2.15 2.70 3.00 3.20 3.25
8.0 4.05 4.80 5.10 5.30 5.40 8.0 1.30 2.00 2.30 2.50 2.55
9.0 3.15 3.85 4.15 4.35 4.40 9.0 0.70 1.40 1.80 1.95 2.00
10.0 2.45 3.10 3.40 3.60 3.65 10.0 1.00 1.45 1.55 1.60
11.0 1.80 2.50 2.85 3.00 3.05 11.0 0.60 1.05 1.20 1.25
12.0 2.05 2.40 2.55 2.60 12.0 0.70 0.90 0.95
13.0 1.60 2.00 2.15 2.20 13.0
14.0 1.30 1.70 1.80 1.85 14.0
15.0 1.00 1.40 1.50 1.55 15.0
16.0 0.70 1.10 1.25 1.30 16.0
17.0 0.85 1.05 1.10 17.0
18.0 0.65 0.85 0.90 18.0
19.0 0.65 0.70 19.0
20.0 0.55 20.0
22.0 22.0
Dangerous Dangerous
angle — — — 35° 42° 45° angle — 35° 50° 58° 60° 61°
Outrigger intermediate extended width 5.2 m (Over side) Outrigger intermediate extended width 4.5 m (Over side)
Boom Boom
length (m) length (m)
7.1 13.7 19.8 25.9 30.5 32.0 7.1 13.7 19.8 25.9 30.5 32.0
working working
radius (m) radius (m)
2.5 26.00 21.00 14.50 2.5 28.00 21.00 14.50
3.0 26.00 21.00 14.50 10.60 3.0 26.00 21.00 14.50 10.60
3.5 25.40 21.00 14.50 10.60 7.00 3.5 25.40 21.00 14.50 10.60 7.00
4.0 23.40 20.00 14.50 10.60 7.00 5.90 4.0 22.50 20.00 14.50 10.60 7.70 5.90
4.5 21.40 18.90 14.50 10.60 7.00 5.90 4.5 18.50 17.74 14.50 10.60 7.00 5.90
5.0 17.75 17.60 14.40 10.60 7.00 5.90 5.0 14.50 14.05 14.40 10.60 7.00 5.90
5.5 15.05 13.50 10.60 7.00 5.90 5.5 11.50 12.50 10.60 7.00 5.90
6.0 12.50 12.70 10.40 7.00 5.90 6.0 9.60 10.55 10.40 7.00 5.90
6.5 10.50 11.05 9.80 7.00 5.90 6.5 8.20 9.05 9.55 7.00 5.90
7.0 9.05 10.00 9.25 7.00 5.90 7.0 7.05 7.90 8.36 7.00 5.90
8.0 6.90 7.75 7.80 7.00 5.90 8.0 5.40 6.15 6.60 6.75 5.90
9.0 5.40 6.20 6.50 6.30 5.50 9.0 4.20 4.95 5.35 5.50 5.50
10.0 4.30 5.10 5.50 5.65 5.10 10.0 3.35 4.05 4.40 4.60 4.65
11.0 3.55 4.25 4.60 4.80 4.70 11.0 2.65 3.35 3.70 3.85 3.90
12.0 3.60 3.95 4.15 4.15 12.0 2.80 3.15 3.30 3.35
13.0 3.05 3.35 3.55 3.60 13.0 2.35 2.70 2.85 2.90
14.0 2.60 2.90 3.10 3.15 14.0 1.95 2.30 2.45 2.50
15.0 2.20 2.55 2.70 2.75 15.0 1.60 1.95 2.15 2.15
16.0 1.85 2.20 2.40 2.45 16.0 1.30 1.70 1.85 1.90
17.0 1.55 1.95 2.10 2.15 17.0 1.00 1.40 1.55 1.60
18.0 1.70 1.80 1.85 18.0 1.10 1.30 1.40
19.0 1.45 1.60 1.65 19.0 0.90 1.05 1.15
20.0 1.20 1.40 1.45 20.0 0.70 0.85 0.95
22.0 0.80 1.00 1.05 22.0 0.55 0.65
24.0 0.70 0.75 Dangerous
angle
— — 18° 34° 36°
26.0 0.50
28.0
29.0
Dangerous
angle — — — 18° 24°
9A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
LW250-5
When outriggers are used (32.0 m Boom + Auxiliary jib working) (unit : ton)
Outrigger maximum extended width 6.6 m (360°)
Boom Jib length 7.4 m Boom Jib length 12.6 m
angle tilt tilt tilt tilt tilt angle tilt tilt tilt tilt tilt
(°) 5° 15° 30° 45° 60° (°) 5° 15° 30° 45° 60°
83.0 2.60 2.20 1.80 1.60 1.00 83.0 1.70 1.40 1.00 0.70 0.50
80.0 2.60 2.20 1.80 1.60 1.00 80.0 1.70 1.40 0.96 0.70 0.50
75.0 2.60 2.20 1.80 1.60 1.00 75.0 1.70 1.32 0.87 0.69 0.50
72.0 2.60 2.20 1.80 1.51 0.88 72.0 1.45 1.10 0.83 0.66 0.48
70.0 2.55 2.15 1.80 1.46 0.86 70.0 1.30 1.02 0.80 0.64 0.47
65.0 2.05 1.76 1.57 1.33 0.81 65.0 1.05 0.87 0.72 0.59 0.43
60.0 1.75 1.50 1.31 1.15 0.78 60.0 0.92 0.78 0.66 0.56 0.40
55.0 1.30 1.20 1.11 0.98 55.0 0.80 0.71 0.63 0.54
50.0 0.97 0.92 0.88 0.81 50.0 0.64 0.58 0.53 0.51
45.0 0.62 0.60 0.58 0.58 45.0 0.45 0.44 0.43 0.42
40.0 0.37 0.37 0.37 42.5 0.35 0.38 0.37
Dangerous Dangerous
angle 38° 38° 38° 43° 58° angle 41° 41° 41° 43° 58°
9A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
LW250-5
When outriggers are used (32.0 m Boom + Auxiliary jib working) (unit : ton)
Outrigger minimum extended width 3.8 m (Over side)
Boom Jib length 7.4 m Boom Jib length 12.6 m
angle tilt tilt tilt tilt tilt angle tilt tilt tilt tilt tilt
(°) 5° 15° 30° 45° 60° (°) 5° 15° 30° 45° 60°
83.0 2.60 2.20 1.80 1.60 1.00 83.0 1.70 1.40 1.00 0.70 0.50
80.0 2.60 2.20 1.80 1.60 1.00 80.0 1.70 1.40 0.96 0.70 0.50
75.0 2.60 2.20 1.80 1.60 1.00 75.0 1.70 1.32 0.87 0.69 0.50
72.0 2.15 1.95 1.69 1.51 0.88 72.0 1.45 1.10 0.83 0.66 0.48
70.0 1.73 1.60 1.45 1.35 0.86 70.0 1.30 1.02 0.80 0.64 0.47
65.0 0.90 0.84 0.76 0.70 0.69 65.0 0.58 0.58 0.50 0.45
62.0 0.50 0.50 0.46 0.44
Dangerous Dangerous
60° 60° 60° 60° 63° 63° 63° 63° 63° 68°
angle angle
9A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
LW500-1
When outriggers not are used (unit : ton)
Outrigger maximum extended width Outrigger maximum extended width
7.5m (360°),H-shape 6.8m (Over side),H-shape
Boom Boom
length length
9.8 16.4 23.1 29.7 36.3 39.6 43.0 9.8 16.4 23.1 29.7 36.3 39.6 43.0
Working Working
radius(m) radius(m)
2.5 50.00 30.00 20.00 12.00 2.5 50.00 30.00 20.00 12.00
3.0 50.00 30.00 20.00 12.00 3.0 48.50 30.00 20.00 12.00
3.5 44.50 30.00 20.00 12.00 11.00 3.5 43.00 30.00 20.00 12.00 11.00
4.0 39.50 30.00 20.00 12.00 11.00 8.50 4.0 38.00 30.00 20.00 12.00 11.00 8.50
4.5 35.50 30.00 20.00 12.00 11.00 8.50 7.00 4.5 34.10 30.00 20.00 12.00 11.00 8.50 7.00
5.0 32.00 29.00 20.00 12.00 11.00 8.50 7.00 5.0 30.70 28.60 20.00 12.00 11.00 8.50 7.00
5.5 29.00 27.00 19.80 12.00 11.00 8.50 7.00 5.5 27.70 26.00 19.80 12.00 11.00 8.50 7.00
6.0 26.50 24.60 18.70 12.00 11.00 8.50 7.00 6.0 25.30 23.70 18.70 12.00 11.00 8.50 7.00
6.5 24.00 22.70 17.60 12.00 11.00 8.50 7.00 6.5 23.00 21.60 17.60 12.00 11.00 8.50 7.00
7.0 20.90 16.70 12.00 11.00 8.50 7.00 7.0 19.80 16.70 12.00 11.00 8.50 7.00
8.0 17.80 15.00 12.00 10.10 8.50 7.00 8.0 16.40 15.00 12.00 10.10 8.50 7.00
9.0 15.00 13.40 11.50 9.40 8.50 7.00 9.0 12.80 12.60 11.50 9.40 8.50 7.00
10.0 12.39 11.90 10.50 8.70 7.90 7.00 10.0 10.30 10.10 10.50 8.70 7.90 7.00
11.0 10.17 9.98 9.60 8.10 7.35 6.50 11.0 8.50 8.30 9.30 8.10 7.35 6.50
12.0 8.50 8.31 8.80 7.50 6.85 6.00 12.0 7.07 6.90 7.80 7.50 6.85 6.00
13.0 7.18 7.00 7.80 7.00 6.40 5.60 13.0 5.95 5.78 6.70 7.00 6.40 5.60
14.0 5.94 6.92 6.50 6.00 5.30 14.0 4.86 5.75 6.26 6.00 5.30
16.0 4.33 5.25 5.67 5.30 4.70 16.0 3.47 4.30 4.78 4.95 4.70
18.0 3.18 4.06 4.45 4.53 4.25 18.0 2.45 3.25 3.71 3.87 4.00
20.0 2.20 3.14 3.53 3.69 3.90 20.0 1.45 2.46 2.90 3.05 3.18
22.0 2.42 2.81 2.97 3.10 22.0 1.78 2.26 2.41 2.54
24.0 1.72 2.23 2.38 2.50 24.0 1.15 1.75 1.90 2.00
26.0 1.13 1.76 1.91 2.03 26.0 0.63 1.26 1.48 1.60
28.0 1.29 1.52 1.63 28.0 0.82 1.05 1.24
30.0 0.87 1.10 1.29 30.0 0.67 0.86
32.0 0.74 0.93 32.0 0.54
34.0 0.62 Dangerous — — — — 27° 32° 35°
Dangerous angle
angle — — — — 10° 21° 28°
9A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
LW500-1
When outriggers not are used (unit : ton)
Outrigger maximum extended width Outrigger maximum extended width
5.6m (Over side),H-shape 4.1m (Over side),H-shape
Boom Boom
length length
9.8 16.4 23.1 29.7 36.3 39.6 43.0 9.8 16.4 23.1 29.7 36.3 39.6 43.0
Working Working
radius(m) radius(m)
2.5 45.00 30.00 20.00 12.00 2.5 40.00 30.00 20.00 12.00
3.0 45.00 30.00 20.00 12.00 3.0 40.00 30.00 20.00 12.00
3.5 40.00 30.00 20.00 12.00 11.00 3.5 34.30 30.00 20.00 12.00 11.00
4.0 35.50 30.00 20.00 12.00 11.00 8.50 4.0 28.80 28.00 20.00 12.00 11.00 8.50
4.5 31.80 29.10 20.00 12.00 11.00 8.50 7.00 4.5 22.20 21.80 20.00 12.00 11.00 8.50 7.00
5.0 28.60 26.20 20.00 12.00 11.00 8.50 7.00 5.0 17.80 17.50 17.30 12.00 11.00 8.50 7.00
5.5 25.90 23.70 19.80 12.00 11.00 8.50 7.00 5.5 14.70 14.40 14.20 12.00 11.00 8.50 7.00
6.0 21.40 21.00 18.70 12.00 11.00 8.50 7.00 6.0 12.40 12.10 11.90 12.00 11.00 8.50 7.00
6.5 18.10 17.70 17.40 12.00 11.00 8.50 7.00 6.5 10.60 10.30 10.10 11.30 11.00 8.50 7.00
7.0 15.10 14.90 12.00 11.00 8.50 7.00 7.0 8.92 8.70 9.80 10.20 8.50 7.00
8.0 11.50 11.30 12.00 10.10 8.50 7.00 8.0 6.77 6.60 7.60 8.10 8.30 7.00
9.0 9.00 8.90 9.90 9.40 8.50 7.00 9.0 5.23 5.11 6.06 6.50 6.70 6.90
10.0 7.29 7.10 8.10 8.67 7.90 7.00 10.0 4.09 3.96 4.86 5.37 5.55 5.70
11.0 5.93 5.79 6.70 7.25 7.35 6.50 11.0 3.20 3.07 3.94 4.42 4.60 4.75
12.0 4.87 4.73 5.63 6.14 6.30 6.00 12.0 2.50 2.36 3.20 3.67 3.84 3.98
13.0 4.04 3.87 4.74 5.24 5.41 5.56 13.0 1.79 1.70 2.60 3.05 3.22 3.36
14.0 3.17 4.02 4.49 4.67 4.81 14.0 1.10 2.09 2.54 2.70 2.84
16.0 2.05 2.90 3.35 3.51 3.65 16.0 1.18 1.74 1.89 2.02
18.0 1.05 2.07 2.51 2.67 2.80 18.0 1.07 1.29 1.41
20.0 1.31 1.87 2.02 2.14 20.0 0.72 0.91
22.0 0.69 1.32 1.51 1.63 Dangerous
— — 42° 47° 53° 55° 57°
24.0 0.80 1.03 1.21 angle
26.0 0.60 0.80
Dangerous
angle — — 20° 32° 41° 43° 46°
9A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
LW500-1
When outriggers not are used (Auxiliary jib working)
Outrigger maximum extended width 7.5m (360°),H-shape
Boom length 7.4m Boom length:12.6m
Boom Boom
angle tilt 5° tilt 25° tilt 45° tilt 60° angle tilt 5° tilt 25° tilt 45° tilt 60°
(°) Working Load Working Load Working Load Working Load (°) Working Load Working Load Working Load Working Load
radiius(m) (ton) radiius(m) (ton) radiius(m) (ton) radiius(m) (ton) radiius(m) (ton) radiius(m) (ton) radiius(m) (ton) radiius(m) (ton)
83 5.3 3.50 7.4 2.40 8.9 1.60 9.5 1.00 83 6.6 2.50 10.6 1.40 13.3 0.90 14.3 0.50
77 10.9 3.50 12.6 2.40 14.0 1.60 14.2 1.00 77 13.1 2.50 17.2 1.40 19.2 0.90 19.4 0.50
74 13.5 3.50 15.2 2.40 16.5 1.57 16.5 0.95 74 16.1 2.23 20.3 1.40 22.0 0.87 21.8 0.49
72 15.3 3.25 16.9 2.25 18.2 1.54 18.1 0.88 72 18.1 2.02 22.2 1.31 23.7 0.85 23.4 0.48
70 17.0 2.95 18.6 2.10 19.7 1.51 19.6 0.86 70 20.0 1.87 24.1 1.25 25.4 0.83 24.9 0.47
68 18.7 2.65 20.2 1.98 21.3 1.48 21.1 0.84 68 21.8 1.72 25.9 1.19 27.1 0.81 26.4 0.45
65 21.2 2.25 22.6 1.83 23.5 1.43 23.2 0.81 65 24.4 1.54 28.5 1.09 29.5 0.79 28.5 0.43
60 25.1 1.85 26.5 1.57 27.1 1.35 26.7 0.78 60 28.6 1.30 30.9 1.00 33.2 0.76 31.9 0.40
55 28.6 1.35 29.9 1.29 30.3 1.15 — — 55 32.4 1.10 34.6 0.88 35.5 0.74 — —
50 31.8 0.80 33.1 0.75 33.2 0.75 — — 50 35.9 0.69 37.9 0.55 38.5 0.52 — —
48 33.0 0.50 34.2 0.50 34.3 0.50 — — 48 37.2 0.48 39.1 0.45 40.0 0.44 — —
Dangerous Dangerous
angle 47° 47° 47° 59° angle 47° 47° 47° 59°
9A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
LW500-1
When outriggers not are used (Boom working)
Hoisting Hoisting
Boom Forward Boom 360° Boom Forward Boom 360°
length length length length
Working 9.8 16.4 23.1 Working 9.8 16.4 23.1 Working 9.8 16.4 23.1 Working 9.8 16.4 23.1
radius(m) radius(m) radius(m) radius(m)
3.0 20.00 15.00 3.0 12.50 10.00 3.0 14.50 10.50 3.0 8.00 6.50
3.5 20.00 15.00 3.5 12.50 10.00 3.5 14.50 10.50 3.5 8.00 6.50
4.0 20.00 15.00 11.00 4.0 11.00 10.00 5.50 4.0 14.50 10.50 8.00 4.0 8.00 6.50 4.50
4.5 18.00 15.00 11.00 4.5 9.10 8.50 5.50 4.5 12.90 10.50 8.00 4.5 6.80 6.50 4.50
5.0 16.00 15.00 11.00 5.0 7.45 7.00 5.50 5.0 11.50 10.50 8.00 5.0 5.80 5.40 4.50
5.5 14.30 14.00 11.00 5.5 6.20 5.75 5.30 5.5 10.30 10.50 8.00 5.5 4.80 4.45 4.25
6.0 12.80 13.00 11.00 6.0 5.20 4.80 4.40 6.0 9.30 10.00 8.00 6.0 4.00 3.70 3.55
6.5 11.70 12.00 10.50 6.5 4.35 4.05 3.65 6.5 8.60 9.30 8.00 6.5 3.35 3.15 3.05
7.0 11.00 9.60 7.0 3.40 3.05 7.0 8.50 7.50 7.0 2.70 2.55
8.0 9.00 8.10 8.0 2.30 2.10 8.0 7.00 6.80 8.0 1.85 1.65
9.0 7.40 6.80 9.0 1.55 1.40 9.0 5.90 5.80 9.0 1.10 0.95
10.0 6.15 5.70 10.0 0.85 0.75 10.0 4.90 4.70 10.0
11.0 5.05 4.75 11.0 11.0 4.00 3.80 11.0
12.0 4.15 3.90 12.0 12.0 3.30 3.10 12.0
13.0 3.45 3.20 13.0 13.0 2.80 2.60 13.0
14.0 2.65 14.0 14.0 2.20 14.0
16.0 1.75 16.0 16.0 1.50 16.0
18.0 1.00 18.0 18.0 0.85 18.0
Dangerous — — 27° Dangerous — 60° 60° Dangerous — — 27° Dangerous — 45° 61°
angle angle angle angle
9A-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
LW100-1
40
20
29
21.5m Boom+4.0m Jib
70
21.5m Boom+0.7m Jib 83
60
25
21.5m Boom
50
18.0m Boom
40
20
Lifting height (m)
14.5m Boom
30
15
11.1m Boom
20
7.6m Boom
10
4.1m Boom 10
0
0 5 10 15 20 25
Working radius (m) FVBH0087
LW250-5
50
45
12.6m
5
25
7.4m
45 40
32.0m Boom 35
83
Lifting height (m)
25.9m Boom 70
30
60
55
50
45 25
19.8m Boom
40
35
20
30
13.7m Boom
20 15
7.6m Boom
10 10
0
0 5 10 15 20 25 30 35
Working radius (m)
FVBH0088
This figure indicates the relation between working radius and lifting height above ground in the state where
outriggers are fully extended, and does not include boom deflection.
9A-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
LW500-1
60
5
Jib
25 55
12.6m
45
Jib
60
7.4m
50
43.0m Boom 45
39.6m Boom
36.3m Boom 40
83
77 72
Lifting height (m)
29.7m Boom 70 35
65
60
55 30
23.1m Boom 50
45
40 25
16.4m Boom 35
30 20
25
9.8m Boom 15
20
15
10
10
5
0
0
0 5 10 15 20 25 30 35
Working radius (m) FVBH0089
This figure indicates the relation between working radius and lifting height above ground in the state where
outriggers are fully extended, and does not include boom deflection.
9A-22
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 9B
REACH TOWER CRANES
CONTENTS
Features .................................................................... 9B-2
Specifications ........................................................... 9B-3
Dimensions ............................................................... 9B-4
Total Rated Loads:
LT300-2 ................................................................. 9B-5
LT500-1 ............................................................... 9B-20
Working Radius vs. Lifting Height
LT300-2 ............................................................... 9B-22
LT500-1 ............................................................... 9B-24
9B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Superior workability
• Compact yet providing powerful lifting capacity.
Komatsu reach-tower cranes feature an innovative combination of a 4-stage main boom and a 6-stage
horizontal telescopic boom. Their rated total load is 420 kg, at the working radius of 18 m, providing users
with a wide working range. In addition, the maximum lift above the ground is 29.6 m, making these ma-
chines very effective when used for work in high places. (LT300)
• Powerful lifting capacity.
An innovative combination of a 3-stage main boom and a 4-stage horizontal telescopic has been used.
Since the rated total load is 1.6tons at the working radius of 25 m, a working range wider than that of a 50-
ton crane is available. The maximum lift above the ground is 47 m, so these machines are very effective
and well-suited for work in high places. (LT500)
• Excellent horizontal reach between swing center and load center.
Loads can be carried forward and backward horizontally.
An excellent horizontal reach is available thanks to the Komatsu engineered combination of the main
boom and horizontal telescopic boom. The horizontal boom is extracted and retracted hydraulically, and
can be used to move a load forward and backward horizontally, unlike the common jib.
(Other features are same as LW100 and LW250.)
9B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
9B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
C H
D E F
A
FVPM0215
Unit: mm (ft.in)
A B C D E F G H (Max.) I
LT300-2 7165 2830 2000 1730 2800 1705 4780 4750 1430
(23'6") (9'3") (6'7") (5'8") (9'2") (5'7") (15'8") (15'7") (4'8")
LT500-1 11330 3685 2620 1680 3500 2300 6400 6300 3030
(37'2") (12'1") (8'7") (5'6") (11'6") (7'7") (21") (20'8") (9'11")
9B-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
LT300-2
Main hook working Unit: ton
Outrigger maximum extended width 4.75 m (Working radius ← Main boom angle)
Working Main boom length 5.0 m Main boom length 8.3 m Main boom length 11.6 m Main boom length 14.9 m
radius Horizontal boom angle Horizontal boom angle Horizontal boom angle Horizontal boom angle
(m) 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75°
2.0 4.90
2.5 4.51 4.34 4.90
3.0 4.01 3.97 4.67 4.21 4.46
3.5 3.61 3.64 3.15 4.20 3.79 4.07 3.98 4.07
4.0 3.27 3.36 2.98 2.95 3.78 3.44 3.16 3.06 3.72 3.61 3.72 3.20
4.5 2.99 3.10 2.84 2.92 3.42 3.14 3.04 2.99 3.40 3.29 3.15 3.05 3.40 2.97
5.0 2.75 2.86 2.73 (4.1) 3.11 2.89 2.83 2.83 3.11 3.00 2.93 2.91 3.11 2.77 2.41 2.37
5.5 2.54 2.66 2.69 2.84 2.66 2.62 (4.9) 2.84 2.74 2.69 2.68 2.84 2.58 2.28 2.25
6.0 2.36 2.47 (5.2) 2.61 2.47 2.44 2.61 2.52 2.47 2.56 2.61 2.42 2.16 2.14
7.0 2.08 2.19 2.13 2.13 2.17 1.71 2.13 2.13 (5.7) 2.13 2.13 1.94 1.99
8.0 2.06 (6.8) 1.71 1.71 (6.8) 1.29 1.71 1.71 1.71 1.71 1.71 (6.6)
9.0 (7.1) 1.29 1.29 0.94 1.29 1.50 1.29 1.29 1.29
10.0 0.94 1.05 0.74 0.94 (8.5) 0.94 0.94 0.94
11.0 0.90 (9.6) 0.60 0.74 0.74 0.74
12.0 (10.2) 0.46 0.60 0.60 0.60
13.0 0.41 0.53 0.46 0.46
14.0 (13.4) (12.5) 0.34 0.34
Dangerous
angle
— — — — — — — — 8° 15° 41° 55° 33° 33° 46° 60°
9B-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
LT300-2
Main hook working Unit: ton
Outrigger extended width 3.40 m (Working radius ← Main boom angle)
Working Main boom length 5.0 m Main boom length 8.3 m Main boom length 11.6 m Main boom length 14.9 m
radius Horizontal boom angle Horizontal boom angle Horizontal boom angle Horizontal boom angle
(m) 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75°
2.0 4.90
2.5 4.51 4.34 4.90
3.0 4.01 3.97 4.67 4.21 4.46
3.5 3.61 3.64 3.15 4.20 3.79 4.07 3.98 4.07
4.0 3.27 3.36 2.98 2.95 3.78 3.44 3.16 3.06 3.72 3.61 3.72 3.20
4.5 2.99 3.10 2.84 2.92 3.42 3.14 3.04 2.99 3.40 3.29 3.15 3.05 3.40 2.97
5.0 2.75 2.86 2.73 (4.1) 3.11 2.89 2.83 2.83 3.11 3.00 2.93 2.91 3.11 2.77 2.41 2.37
5.5 2.54 2.66 2.69 2.84 2.66 2.62 (4.9) 2.84 2.74 2.69 2.68 2.84 2.58 2.28 2.25
6.0 2.36 2.47 (5.2) 2.61 2.47 2.44 2.51 2.52 2.47 2.56 2.54 2.42 2.16 2.14
7.0 2.08 2.19 2.13 1.96 2.15 1.81 1.88 1.99 (5.7) 1.85 1.92 1.94 1.99
8.0 2.01 (6.8) 1.71 1.45 (6.8) 1.32 1.38 1.45 1.36 1.42 1.51 (6.6)
9.0 (7.1) 1.06 1.07 0.97 1.01 1.24 1.01 1.06 1.12
10.0 0.77 0.89 0.66 0.70 (8.5) 0.72 0.78 0.83
11.0 0.71 (9.6) 0.38 0.41 0.45 0.49
12.0 (10.2)
Dangerous 13° 19° 36° 46° 16° 24° 41° 51° 36° 37° 46° 56° 49° 49° 50° 61°
angle
Main hook working Unit: ton
Outrigger extended width 2.80 m (Working radius ← Main boom angle)
Working Main boom length 5.0 m Main boom length 8.3 m Main boom length 11.6 m Main boom length 14.9 m
radius Horizontal boom angle Horizontal boom angle Horizontal boom angle Horizontal boom angle
(m) 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75°
2.0 4.90
2.5 4.51 4.34 3.15 4.90
3.0 4.01 3.97 2.98 2.95 4.67 4.21 4.46
3.5 3.61 3.64 2.84 2.92 4.20 3.79 3.16 3.06 4.07 3.98 4.07
4.0 3.27 3.36 2.73 (4.1) 3.78 3.44 3.04 2.99 3.72 3.61 3.72 3.20
4.5 2.99 3.10 2.69 3.27 3.14 2.83 2.83 3.17 3.29 3.15 3.05 3.21 2.97
5.0 2.75 2.86 (5.2) 2.66 2.77 2.41 (4.9) 2.56 2.69 2.90 2.91 2.60 2.72 2.41 2.37
5.5 2.38 2.43 2.20 2.28 2.01 2.10 2.21 2.38 2.40 2.14 2.24 2.28 2.25
6.0 2.01 2.04 1.83 1.90 1.51 1.74 1.83 1.97 2.22 1.77 1.87 2.02 2.04
7.0 1.46 1.56 1.30 1.35 (6.8) 1.21 1.28 1.38 5.7 1.24 1.32 1.43 1.65
8.0 1.41 (6.8) 0.92 0.96 0.84 0.89 0.95 0.87 0.93 1.02 (6.6)
9.0 (7.1) 0.60 0.62 0.48 0.54 0.78 0.54 0.66 0.68
10.0 (8.5)
11.0
12.0
Dangerous 13° 19° 39° 46° 22° 24° 44° 51° 48° 49° 49° 56° 57° 58° 58° 61°
angle
Working Main boom length 5.0 m Main boom length 8.3 m Main boom length 11.6 m Main boom length 14.9 m
radius Horizontal boom angle Horizontal boom angle Horizontal boom angle Horizontal boom angle
(m) 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75°
2.0 4.90
2.5 4.51 4.34 4.90
3.0 4.01 3.97 4.46 4.21 4.46
3.5 3.61 3.64 3.15 3.53 3.71 3.43 3.63 3.46
4.0 2.90 3.00 2.98 2.95 2.72 2.87 3.12 3.06 2.63 2.79 2.66 2.83
4.5 2.33 2.41 2.53 2.92 2.15 2.27 2.47 2.50 2.06 2.20 2.44 2.48 2.09 2.23
5.0 1.90 1.96 2.04 (4.1m) 1.73 1.83 1.99 2.09 1.64 1.76 1.95 1.99 1.67 1.79 1.99 2.03
5.5 1.57 1.62 1.88 1.40 1.49 1.61 (4.9m) 1.46 1.41 1.58 1.60 1.35 1.45 1.62 1.65
6.0 1.31 1.34 (5.2m) 1.14 1.21 1.31 1.05 1.14 1.28 1.47 1.09 1.18 1.32 1.34
7.0 0.91 0.98 0.74 0.80 0.93 0.62 0.71 0.83 (5.7m) 0.67 0.77 0.88 1.05
8.0 0.87 (6.8m) 0.38 0.42 (6.8m) 0.33 0.41 0.39 0.50 6.60
9.0 (7.1m)
Dangerous 13° 19° 40° 50° 41° 42° 46° 55° 58° 59° 60° 60° 64° 65° 66° 66°
angle
9B-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
LT300-2
Main hook working Unit: ton
Outrigger minimum extended width 1.65 m (Working radius ← Main boom angle)
Working Main boom length 5.0 m Main boom length 8.3 m Main boom length 11.6 m Main boom length 14.9 m
radius Horizontal boom angle Horizontal boom angle Horizontal boom angle Horizontal boom angle
(m) 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75° 13° 30° 60° 75°
2.0 4.90
2.5 4.36 4.34 4.19
3.0 3.13 3.29 2.96 3.17 2.87
3.5 2.36 2.48 2.70 2.20 2.36 2.11 2.29 2.14
4.0 1.84 1.93 2.09 2.11 1.67 1.80 2.03 2.08 1.58 1.73 1.61 1.77
4.5 1.45 1.52 1.64 2.01 1.29 1.40 1.58 1.61 1.20 1.33 1.55 1.60 1.23 1.36
5.0 1.16 1.21 1.29 (4.1) 1.00 1.09 1.24 1.32 0.91 1.02 1.20 1.24 0.94 1.05 1.24 1.28
5.5 0.93 0.97 1.17 0.77 0.84 0.96 (4.9) 0.64 0.78 0.93 0.95 0.69 0.81 0.97 1.00
6.0 0.74 0.77 (5.2) 0.53 0.62 0.74 0.40 0.52 0.70 0.85 0.45 0.56 0.75 0.77
7.0 (5.7) 0.50
8.0 (6.6)
Dangerous 27° 32° 45° 58° 55° 56° 57° 63° 66° 67° 68° 68° 71° 71° 72° 72°
angle
9B-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 14.9 m/Max. outrigger extended width 4.10 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
4.5 1.40
5.0 1.40
5.5 1.40 1.40
6.0 1.40 1.40 1.40
7.0 1.40 1.40 1.14 1.40 1.40 1.40
8.0 (6.7) 1.31 1.14 0.75 1.40 1.40 0.94 1.40
9.0 1.19 1.10 0.75 0.65 (7.7) 1.22 0.94 0.75 1.40 1.30
10.0 (8.9) 0.97 0.75 0.65 0.65 1.11 0.94 0.75 0.65 (8.6) 1.13 0.90 1.25
11.0 0.87 0.75 0.65 0.65 (9.9) 0.94 0.75 0.65 1.03 0.90 0.65 1.08
12.0 0.75 0.65 0.65 0.90 0.75 0.65 0.55 (10.9) 0.85 0.65 0.55 (10.9) 0.93
13.0 0.75 0.65 0.65 0.89 0.75 0.65 0.55 0.76 0.65 0.55 0.81 0.63
14.0 0.75 0.65 0.65 (12.1) 0.75 0.65 0.55 0.75 0.65 0.55 0.45 0.79 0.63
15.0 (13.3) 0.65 0.64 0.75 0.65 0.55 (13.1) 0.65 0.55 0.45 (13.2) 0.63 0.48
16.0 0.65 0.58 (14.3) 0.65 0.55 0.65 0.55 0.45 0.62 0.48 0.37
17.0 (15.4) 0.53 0.65 0.54 (15.2) 0.55 0.45 (15.4) 0.48 0.37
18.0 0.50 (16.4) 0.50 0.55 0.45 0.48 0.37 0.30
19.0 (17.6) 0.47 (17.4) 0.45 (17.6) 0.37 0.30
20.0 (18.6) 0.44 0.37 0.30
21.0 (19.6) (19.2) 0.30
22.0 0.30
(21.9)
9B-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 14.9 m/Max. outrigger extended width 2.80 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
4.5 1.40
5.0 1.40
5.5 1.40 1.40
6.0 1.40 1.40 1.40
7.0 1.40 1.40 1.14 1.40 1.40 1.29
8.0 (6.7) 1.31 1.14 0.75 1.26 1.19 0.94 1.04
9.0 1.15 1.10 0.75 0.65 (7.7) 0.99 0.94 0.75 0.92 0.86
10.0 (8.9) 0.97 0.75 0.65 0.65 0.85 0.85 0.75 0.65 (8.6) 0.72 0.73
11.0 0.84 0.75 0.65 0.65 (9.9) 0.73 0.75 0.65 0.61 0.62 0.65
12.0 0.75 0.65 0.65 0.63 0.67 0.65 0.55 (10.9) 0.53 0.56 0.55
13.0 0.68 0.65 0.65 0.59 0.61 0.55 0.49 0.51
14.0 0.60 0.63 0.65 0.52 0.54 0.55 0.40 0.45 0.45
15.0 (13.3) 0.57 0.59 0.50 0.49 0.50 0.36 0.39 0.41
16.0 0.54 0.53 (14.3) 0.43 0.45 0.34 0.34 0.36
17.0 (15.4) 0.48 0.42 0.41 (15.2) 0.29 0.32
18.0 0.46 (16.4) 0.37 0.27 0.28
19.0 (17.6) 0.35 (17.4)
20.0 (18.6)
9B-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 14.9 m/Max. outrigger minimum extended width 1.65 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
4.5 1.27
5.0 1.08
5.5 0.93 0.93
6.0 0.81 0.80 0.58
7.0 0.67 0.62 0.63 0.40 0.39
8.0 (6.7) 0.47 0.50 0.53 0.29 0.26
9.0 0.36 0.38 0.43 0.46 (7.7)
10.0 (8.9) 0.28 0.33 0.37 0.39
11.0 0.26 0.29 0.32
12.0 0.26
9B-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 8.3 m/Max. outrigger extended width 4.10 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
3.5 1.40
4.0 1.40 1.40
4.5 1.40 1.40 1.40
5.0 1.40 1.40 1.40 1.40
5.5 1.40 1.40 1.14 1.40 1.40 1.40
6.0 (5.3) 1.40 1.14 0.75 1.40 1.40 1.40 1.35
7.0 1.40 1.14 0.75 0.65 (5.8) 1.40 0.94 1.40 1.35 1.40
8.0 1.40 1.14 0.75 0.65 0.65 1.40 0.94 0.75 (6.4) 1.35 0.90 1.40
9.0 (7.5) 1.14 0.75 0.65 0.65 1.40 0.94 0.75 0.65 1.35 0.90 0.65 (7.6) 1.00 1.40
10.0 1.12 0.75 0.65 0.65 (8.1) 0.94 0.75 0.65 0.55 (8.6) 0.90 0.65 0.55 1.00 0.63 (8.7) 0.82
11.0 (9.7) 0.75 0.65 0.65 0.94 0.75 0.65 0.55 0.90 0.65 0.55 0.45 (9.9) 0.63 0.48 0.82
12.0 0.75 0.65 0.65 (10.3) 0.75 0.65 0.55 (10.8) 0.65 0.55 0.45 0.63 0.48 0.48
13.0 (11.9) 0.65 0.65 0.75 0.65 0.55 0.65 0.55 0.45 0.63 0.48 0.37 0.48
14.0 0.65 0.65 (12.5) 0.65 0.55 0.55 0.45 (12.1) 0.48 0.37 0.30 0.48 0.36
15.0 0.65 0.65 0.65 0.55 0.55 0.45 0.48 0.37 0.30 (13.2) 0.36
16.0 (14.1) 0.62 (14.6) 0.55 0.55 0.45 (14.3) 0.37 0.30 0.36
17.0 0.61 0.55 (15.2) 0.45 0.37 0.30 (15.4)
9B-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 11.6 m/Max. outrigger extended width 4.75 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
3.5 1.40
4.0 1.40
4.5 1.40
5.0 1.40 1.40 1.40
5.5 1.40 1.40 1.40
6.0 1.40 1.40 1.14 1.40 1.40 1.40
7.0 1.40 1.14 0.75 1.40 1.40 0.94 1.40
8.0 1.40 1.14 0.75 0.65 (6.7) 1.40 0.94 1.40 1.35
9.0 1.40 1.14 0.75 0.65 0.65 1.40 0.94 0.75 (7.5) 1.35 0.90 1.40
10.0 (8.2) 1.14 0.75 0.65 0.65 0.94 0.75 0.65 1.35 0.90 0.65 1.40 1.00
11.0 1.12 0.75 0.65 0.65 0.94 0.75 0.65 0.55 (9.8) 0.90 0.65 0.55 (9.3) 1.00 1.19
12.0 (10.4) 0.75 0.65 0.65 0.94 0.75 0.65 0.55 0.90 0.65 0.55 0.45 1.00 0.63 (10.9) 0.78
13.0 0.75 0.65 0.65 (11.2) 0.75 0.65 0.55 0.65 0.55 0.45 (11.5) 0.63 0.48 0.78
14.0 (12.6) 0.65 0.65 0.75 0.65 0.55 0.65 0.55 0.45 0.63 0.48 0.78 0.48
15.0 0.65 0.65 (13.4) 0.65 0.55 0.65 0.55 0.45 (13.7) 0.48 0.37 (13.1) 0.48
16.0 (14.8) 0.65 0.65 0.55 (14.1) 0.55 0.45 0.48 0.37 0.30 0.48 0.36
17.0 0.61 (15.5) 0.55 0.55 0.45 (15.9) 0.37 0.30 (15.3) 0.36
18.0 (16.9) 0.55 (16.3) 0.45 0.37 0.30 0.36
19.0 (17.7) 0.45 0.37 0.30 (17.5)
9B-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 11.6 m/Max. outrigger extended width 3.40 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
3.5 1.40
4.0 1.40
4.5 1.40
5.0 1.40 1.40 1.40
5.5 1.40 1.40 1.40
6.0 1.40 1.40 1.14 1.40 1.40 1.40
7.0 1.40 1.14 0.75 1.40 1.40 0.94 1.40
8.0 1.40 1.14 0.75 0.65 (6.7) 1.40 0.94 1.40 1.35
9.0 1.40 1.14 0.75 0.65 0.65 1.40 0.94 0.75 (7.5) 1.35 0.90 1.12
10.0 (8.2) 1.14 0.75 0.65 0.65 0.94 0.75 0.65 1.22 0.90 0.65 1.06 0.95
11.0 1.12 0.75 0.65 0.65 0.94 0.75 0.65 0.55 (9.8) 0.90 0.65 0.55 (9.3) 0.81 0.59
12.0 (10.4) 0.75 0.65 0.65 0.94 0.75 0.65 0.55 0.90 0.65 0.55 0.45 0.75 0.63 (10.9) 0.47
13.0 0.75 0.65 0.65 (11.2) 0.75 0.65 0.55 0.65 0.55 0.45 (11.5) 0.62 0.48 0.38
14.0 (12.6) 0.65 0.65 0.75 0.65 0.55 0.65 0.55 0.45 0.56 0.48 0.37 0.32
15.0 0.65 0.65 (13.4) 0.65 0.55 0.65 0.55 0.45 (13.7) 0.48 0.37 (13.1) 0.26
16.0 (14.8) 0.65 0.65 0.55 (14.1) 0.55 0.45 0.45 0.37 0.30 0.24
17.0 0.61 (15.5) 0.55 0.55 0.45 (15.9) 0.37 0.30 (15.3)
9B-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 11.6 m/Max. outrigger extended width 2.20 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
3.5 1.40
4.0 1.40
4.5 1.40
5.0 1.40 1.40 1.40
5.5 1.40 1.40 1.40
6.0 1.40 1.40 1.14 1.31 1.31 1.13
7.0 1.18 1.14 0.75 1.10 1.03 0.94 0.89
8.0 0.96 0.98 0.75 0.65 (6.7) 0.83 0.85 0.79 0.71
9.0 0.92 0.81 0.75 0.65 0.65 0.68 0.70 0.65 (7.5) 0.57 0.59
10.0 (8.2) 0.68 0.73 0.65 0.65 0.59 0.62 0.65 0.47 0.47 0.52
11.0 0.64 0.63 0.65 0.65 0.49 0.53 0.56 0.55 (9.8) 0.37 0.42 0.45
12.0 (10.4) 0.54 0.57 0.59 0.48 0.46 0.48 0.50 0.27 0.35 0.38 0.40
13.0 0.50 0.50 0.52 (11.2) 0.39 0.42 0.44 0.28 0.32 0.34
14.0 (12.6) 0.44 0.46 0.36 0.37 0.39 0.26 0.29
15.0 0.40 0.42 (13.4) 0.31 0.34
16.0 (14.8) 0.37 0.29 0.30
17.0 0.34 (15.5) 0.25
18.0 (16.9)
9B-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 8.3 m/Max. outrigger extended width 2.80 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
2.5
3.0.
3.5 1.40
4.0 1.40 1.40
4.5 1.40 1.40 1.40
5.0 1.40 1.40 1.40 1.40
5.5 1.40 1.40 1.14 1.40 1.40 1.40
6.0 (5.3) 1.40 1.14 0.75 1.40 1.40 1.40 1.35
7.0 1.40 1.14 0.75 0.65 (5.8) 1.40 0.94 1.40 1.35 1.40
8.0 1.40 1.14 0.75 0.65 0.65 1.40 0.94 0.75 (6.4) 1.35 0.90 1.26
9.0 (7.5) 1.14 0.75 0.65 0.65 1.40 0.94 0.75 0.65 1.35 0.90 0.65 (7.6) 0.97 0.85
10.0 1.12 0.75 0.65 0.65 (8.1) 0.94 0.75 0.65 0.55 (8.6) 0.90 0.65 0.55 0.83 0.63 (8.7) 0.67
11.0 (9.7) 0.75 0.65 0.65 0.94 0.75 0.65 0.55 0.90 0.65 0.55 0.45 (9.9) 0.63 0.48 0.56
12.0 0.75 0.65 0.65 (10.3) 0.75 0.65 0.55 (10.8) 0.65 0.55 0.45 0.61 0.48 0.48
13.0 (11.9) 0.65 0.65 0.75 0.65 0.55 0.65 0.55 0.45 0.60 0.48 0.37 0.39
14.0 0.65 0.65 (12.5) 0.65 0.55 0.55 0.45 (12.1) 0.48 0.37 0.30 0.38 0.36
15.0 0.65 0.65 0.65 0.55 0.55 0.45 0.48 0.37 0.30 (13.2) 0.31
16.0 (14.1) 0.62 (14.6) 0.55 0.55 0.45 (14.3) 0.37 0.30 0.29
17.0 0.61 0.55 (15.2) 0.45 0.37 0.30 (15.4)
9B-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 8.3 m/Max. outrigger extended width 1.65 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
3.5 1.40
4.0 1.40 1.40
4.5 1.40 1.40 1.40
5.0 1.40 1.40 1.26 1.12
5.5 1.28 1.22 1.14 1.09 1.09 0.96
6.0 (5.3) 1.07 1.08 0.75 1.00 0.95 0.84 0.83
7.0 0.84 0.86 0.75 0.65 (5.8) 0.74 0.76 0.75 0.64
8.0 0.75 0.69 0.74 0.65 0.65 0.59 0.61 0.65 (6.4) 0.50 0.52
9.0 (7.5) 0.57 0.61 0.64 0.65 0.57 0.49 0.53 0.56 0.42 0.40 0.46
10.0 0.50 0.52 0.54 0.56 (8.1) 0.40 0.45 0.47 0.49 (8.6) 0.30 0.36 0.40
11.0 (9.7) 0.44 0.47 0.49 0.37 0.37 0.40 0.42 0.28 0.32 0.35
12.0 0.38 0.40 0.42 (10.3) 0.30 0.34 0.36 0.26 0.28
13.0 (11.9) 0.35 0.37 0.27 0.28 0.31
14.0 0.31 0.33 (12.5) 0.23 0.26
15.0 0.30 0.29
16.0 (14.1)
9B-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 5.0 m/Max. outrigger extended width 4.10 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
2.5 1.40
3.0 1.40 1.40
3.5 1.40 1.40 1.40
4.0 1.40 1.40 1.40 1.40
4.5 1.40 1.40 1.14 1.40 1.40 1.40
5.0 1.40 1.40 1.14 1.40 1.40 1.40 1.35 1.40
5.5 (4.6) 1.40 1.14 0.75 (4.9) 1.40 1.01 1.40 1.35 1.40
6.0 1.40 1.14 0.75 1.40 1.01 (5.2) 1.35 0.90 1.40 1.40
7.0 1.40 1.14 0.75 0.65 1.40 1.01 0.75 1.35 0.90 1.00 1.40
8.0 (6.9) 1.14 0.75 0.65 0.65 1.40 1.01 0.75 0.65 1.35 0.90 0.65 1.00 0.63 (6.6) 0.82
9.0 1.12 0.75 0.65 0.65 (7.2) 1.01 0.75 0.65 0.55 (7.5) 0.90 0.65 0.55 1.00 0.63 0.82
10.0 0.75 0.65 0.65 1.01 0.75 0.65 0.55 0.90 0.65 0.55 0.45 (8.2) 0.63 0.48 (8.9) 0.48
11.0 0.75 0.65 0.65 (9.4) 0.75 0.65 0.55 (9.7) 0.65 0.55 0.45 0.63 0.48 0.37 0.48
12.0 0.75 0.65 0.65 0.75 0.65 0.55 0.65 0.55 0.45 (10.4) 0.48 0.37 0.36
13.0 (11.2) 0.65 0.65 (11.5) 0.65 0.55 (11.9) 0.55 0.45 0.48 0.37 0.30 0.36
14.0 0.65 0.65 0.65 0.55 0.55 0.45 (12.6) 0.37 0.30 0.36
15.0 (13.4) 0.63 (13.7) 0.55 0.55 0.45 0.37 0.30 (13.2)
9B-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 5.0 m/Max. outrigger extended width 2.80 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
2.5 1.40
3.0 1.40 1.40
3.5 1.40 1.40 1.40
4.0 1.40 1.40 1.40 1.40
4.5 1.40 1.40 1.14 1.40 1.40 1.40
5.0 1.40 1.40 1.14 1.40 1.40 1.40 1.35 1.40
5.5 (4.6) 1.40 1.14 0.75 (4.9) 1.40 1.01 1.40 1.35 1.40
6.0 1.40 1.14 0.75 1.40 1.01 (5.2) 1.35 0.90 1.40 1.40
7.0 1.40 1.14 0.75 0.65 1.40 1.01 0.75 1.35 0.90 1.00 1.40
8.0 (6.9) 1.14 0.75 0.65 0.65 1.40 1.01 0.75 0.65 1.35 0.90 0.65 1.00 0.63 (6.6) 0.82
9.0 1.12 0.75 0.65 0.65 (7.2) 1.01 0.75 0.65 0.55 (7.5) 0.90 0.65 0.55 1.00 0.63 0.82
10.0 0.75 0.65 0.65 1.01 0.75 0.65 0.55 0.90 0.65 0.55 0.45 (8.2) 0.63 0.48 (8.9) 0.48
11.0 0.75 0.65 0.65 (9.4) 0.75 0.65 0.55 (9.7) 0.65 0.55 0.45 0.63 0.48 0.37 0.48
12.0 0.75 0.65 0.65 0.75 0.65 0.55 0.65 0.55 0.45 (10.4) 0.48 0.37 0.36
13.0 (11.2) 0.65 0.65 (11.5) 0.65 0.55 (11.9) 0.55 0.45 0.48 0.37 0.30 0.36
14.0 0.65 0.65 0.65 0.55 0.55 0.45 (12.6) 0.37 0.30 0.36
15.0 (13.4) 0.63 (13.7) 0.55 0.55 0.45 0.37 0.30 (13.2)
9B-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working Unit: ton
Main boom length 5.0 m/Max. outrigger extended width 1.65 m (Working radius ← Horizontal boom angle)
Main boom angle 78° Main boom angle 74° Main boom angle 70° Main boom angle 60° Main boom angle50°
Work-
ing Horizontal boom
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) length(m)
(m)
3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5 12.7 14.9 3.9 6.2 8.4 10.5
2.5 1.40
3.0 1.40 1.40
3.5 1.40 1.40 1.40
4.0 1.40 1.40 1.40 1.40
4.5 1.40 1.40 1.14 1.40 1.40 1.40
5.0 1.40 1.40 1.14 1.40 1.40 1.40 1.35 1.26
5.5 (4.6) 1.39 1.14 0.75 (4.9) 1.32 1.01 1.36 1.25 1.09
6.0 1.23 1.14 0.75 1.16 1.01 (5.2) 1.10 0.90 0.95 0.83
7.0 0.99 1.00 0.75 0.65 0.92 0.94 0.75 0.86 0.89 0.75 0.70
8.0 (6.9) 0.81 0.75 0.65 0.65 0.87 0.76 0.75 0.65 0.77 0.72 0.65 0.59 0.61 (6.6) 0.49
9.0 0.60 0.72 0.65 0.65 (7.2) 0.63 0.68 0.65 0.55 (7.5) 0.59 0.63 0.55 0.56 0.50 0.38
10.0 0.61 0.64 0.65 0.58 0.57 0.60 0.55 0.52 0.54 0.55 0.45 (8.2) 0.41 0.45 (8.9)
11.0 0.52 0.56 0.58 (9.4) 0.49 0.52 0.54 (9.7) 0.46 0.48 0.45 0.36 0.37 0.37
12.0 0.51 0.48 0.51 0.45 0.45 0.47 0.39 0.42 0.44 (10.4) 0.30 0.34
13.0 (11.2) 0.42 0.45 (11.5) 0.39 0.42 (11.9) 0.36 0.39 0.26 0.28
14.0 0.40 0.40 0.36 0.37 0.33 0.34 (12.6)
9B-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
LT500-1
Main hook working Unit: ton
Outrigger maximum extended width 6.3 m (Working radius ← Main boom angle)
Working Main boom length 10.9 m Main boom length 17.9 m Main boom length 24.9 m
radius Horizontal boom angle Horizontal boom angle Horizontal boom angle
(m) 20 30 40 55 78 20 30 40 55 78 20 30 40 55 78
2.0
2.5
3.0 12.00
3.5 12.00 11.56 10.00
4.0 12.00 11.05 10.29 10.00
4.5 11.51 10.59 9.90 9.72 9.75
5.0 10.98 10.17 9.53 8.75 8.40 9.00 9.04 9.07
5.5 10.51 9.78 9.19 8.51 8.30 8.36 8.41 8.45 6.00 6.00
6.0 10.07 9.42 8.87 8.28 7.79 7.83 7.87 7.92 7.96 6.00 6.00 6.00 6.00
7.0 9.30 8.78 8.31 7.90 6.78 6.83 6.87 6.91 6.94 5.38 5.46 5.52 5.55 5.51
8.0 8.63 8.20 7.84 7.59 5.93 5.98 6.01 6.04 4.64 4.72 4.77 4.79 4.74
9.0 8.06 7.70 7.45 7.53 5.20 5.24 5.27 5.29 4.01 4.08 4.13 4.15
10.0 7.57 7.28 7.13 4.56 4.61 4.63 4.65 3.47 3.53 3.58 3.59
11.0 6.21 6.27 6.29 4.01 4.05 4.08 4.09 3.00 3.06 3.09 3.10
12.0 5.09 5.12 3.53 3.57 3.59 3.59 2.59 2.64 2.67 2.67
13.0 4.20 3.10 3.13 3.14 3.14 2.22 2.27 2.29 2.28
14.0 2.71 2.74 2.75 1.90 1.94 1.95 1.94
15.0 2.21 2.30 2.34 1.60 1.64 1.65 1.63
16.0 1.62 1.68 1.70 1.34 1.37 1.37 1.35
17.0 1.11 1.15 1.14 1.10 1.12 1.12 1.09
18.0 0.67 0.68 0.72 0.80 0.85
19.0 0.45
Dangerous
29° 30° 49° 49° 50°
angle
9B-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
LT500-1
Auxiliary hook working Unit: ton
Main boom length 17.9 m/Max. outrigger extended width 6.3 m (Working radius ← Horizontal boom angle)
Working Main boom angle 78° Main boom angle 70° Main boom angle 60° Main boom angle 50°
radius Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m) Horizontal boom length (m)
(m) 7.0 12.1 17.1 22.1 7.0 12.1 17.1 22.1 7.0 12.1 17.1 22.1 7.0 12.1 17.1 22.1
4.5 3.00
5.0 3.00
6.0 3.00
7.0 3.00 3.00
8.0 3.00 3.00 3.00 3.00
9.0 3.00 3.00 3.00 3.00
10.0 (8.4) 3.00 3.00 3.00 3.00
11.0 3.00 3.00 3.00 3.00 3.00
12.0 3.00 3.00 3.00 (10.8) 3.00 3.00
13.0 3.00 3.00 2.84 3.00 3.00 3.00
14.0 3.00 2.86 2.65 3.00 3.00 3.00
15.0 (13.4) 2.67 2.47 3.00 3.00 2.90 (13.6) 3.00 2.51
16.0 2.49 2.31 3.00 3.00 2.70 2.96 2.19
17.0 2.33 2.18 (15.8) 2.80 2.53 2.73 2.05
18.0 2.19 2.05 2.62 2.39 2.51 2.40 (16.2)
19.0 2.12 1.94 2.45 2.25 2.19 2.24 1.60
20.0 (18.5) 1.84 2.31 2.13 (18.7) 2.09 1.43
21.0 1.75 2.14 2.02 1.96 1.82 1.28
22.0 1.68 (20.9) 1.91 1.83 1.72 1.23
23.0 1.61 1.82 1.68 1.63 (21.2) 1.06
24.0 1.60 1.74 1.47 1.55 0.96
25.0 0.96 1.66 (23.7) 1.45 0.86
26.0 (23.5) 1.60 1.34 0.78
27.0 (25.9) 1.24 0.74 0.71
28.0 1.15 (26.3) 0.64
29.0 0.90 0.58
30.0 (28.8) 0.52
31.0 0.47
32.0 0.44
33.0 (31.3)
9B-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
LT300-2
Main hook working
33
81.5 30
13
30
Lifting height above ground (m)
25
60
60
14.9m+3.2 Boom
20
81.5
11.6m+3.2 Boom
8.3m+3.2 Boom 15
30
5.0m+3.2 Boom
10
13
5
0
0 5 10 15 21
Working radius (m)
FVBH0090
25 25
14.9m+6.2m Boom 14.9m+6.2m Boom
15 15
10 10
5 5
0 0
0 5 10 15 21 0 5 10 15 21
Working radius (m) Working radius (m)
FVBH0091 FVBH0092
This figure indicates the relation between working radius and lifting height above ground in the state where
outriggers are fully extended, and does not include boom deflection.
9B-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
LT300-2
Auxiliary hook working
25 25
14.9m+6.2m Boom 14.9m+6.2m Boom 30
15 15
10 10
5 5
0 0
0 5 10 15 21 0 5 10 15 21
Working radius (m) Working radius (m)
FVBH0093 FVBH0094
14.9m+14.9m Boom 33 33
14.9m+12.7m Boom
30 30
14.9m+10.5m Boom
14.9m+8.4m Boom 47
14.9m+10.5m Boom
Lifting height above ground (m)
25 25
14.9m+6.2m Boom
14.9m+8.4m Boom
14.9m+3.9m Boom
14.9m+6.2m Boom
20 20
14.9m+3.9m Boom
37
60
15 15
50
10 10
5 5
0 0
0 5 10 15 20 22 0 5 10 15 20 22
Working radius (m) Working radius (m)
FVBH0095 FVBH0096
This figure indicates the relation between working radius and lifting height above ground in the state where
outriggers are fully extended, and does not include boom deflection.
9B-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
LT500-1
Main hook working
40
4 55
30 0
78
20
9
35
24.9m+5.8m Boom
30
17.9m+5.8m Boom
25
Lifting height above ground (m)
10.9m+5.8m Boom 20
15
82
70
60
48 10
40
28
20
5
9
0
0 5 10 1 5 20 25
Working radius (m)
FVBH0097
25 25
20 20
15 15
10 10
82
78
5 5
0 0
0 5 10 15 20 25 30 35 0 5 10 15 20 25 30 35
Working radius (m) Working radius (m)
FVBH0098 FVBH0099
This figure indicates the relation between working radius and lifting height above ground in the state where
outriggers are fully extended, and does not include boom deflection.
9B-24
AH_25.book Page 25 Tuesday, March 23, 2004 9:41 AM
LT500-1
Auxiliary hook working
24.9m+22.1m Boom 50 24.9m+22.1m Boom 50
61
24.9m+17.1m Boom 45 24.9m+17.1m Boom 45
50
51
Lifting height above ground (m)
25 25
20 20
15 15
10 10
70
60
5 5
0 0
0 5 10 15 20 25 30 35 0 5 10 15 20 25 30 35
Working radius (m) Working radius (m)
FVBH0100 FVBH0101
50 50
45 45
Lifting height above ground (m)
Lifting height above ground (m)
17.9m+22.1m Boom 40 40
17.9m+17.1m Boom 35 35
41 10.9m+22.1m Boom
17.9m+12.1m Boom 30 30
30
10.9m+17.1m Boom
17.9m+7.0m Boom 20 25 25
10.9m+12.1m Boom
10
20 26 20
10.9m+7.0m Boom
15 15
10
10 10
50
35
5 5
0 0
0 5 10 15 20 25 30 35 0 5 10 15 20 25 30 35
Working radius (m) Working radius (m)
FVBH0102 FVBH0103
This figure indicates the relation between working radius and lifting height above ground in the state where
outriggers are fully extended, and does not include boom deflection.
9B-25
AH_25.book Page 26 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 10
INDEX
GENERATOR SETS
CONTENTS
Features .....................................................................10-2
Specifications ............................................................10-3
10-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
1. New Engine
Komatsu "Air-to-Air Aftercooled Engine" has been introduced. (Except for EGS45-5 to EGS300-6 , and EGS650-6)
• High Output (Performance)
• Low Fuel Consumption
• Low Noise
• Lighter Weight and Compactness
• Longer Oil Change Interval
• Easy Maintenance
• High Quality, High Reliability, High Durability
2. Easy Operation and Control
2-1.Engine & Generator control panel is arranged in one box, and located in front of Generator.
So the operator can monitor the operating status easily by viewing the meters.
Advantage:
• Simple : Minimized control equipment and wiring
• Easy Maintenance
2-2.Compact Engine Control Unit
EGS Series generators have a compact engine control unit ( 1 box type ) for easy operation and maintenance.
Advantage and Functions
• Microprocessor : Control status and factor are programmed in Microprocessor.
• High Reliability : Engine control circuit is integrated in printed boards.
• Easy selection : A Mode Key Switch for Off / Auto / Manual
• Built-in AMF function : Auto Start / Stop, Cranking with attempts and Cool running are Standard Function.
• Iconic, Symbols and LED : Operating process and Alarm condition can be monitored.
3. High qualified electricity with Brushless, Self-excited AC Alternator
• Maintenance-Free : Brushless, Direct coupling with engine
• High Electric Characteristic : Standard 2/3 pitch windings avoid excessive neutral currents.
• Excellent Voltage Build-Up : Originally designed excited field system and high efficient steel
• Stable Voltage Regulation : Built-in type Automatic Voltage regulator (AVR)
• High Efficient Cooling : Class H insulation with forced air-circulation
• Permanent Magnet Generator (PMG) (Optional ) : PMG systems provides constant excitation
• Voltage Adjustment (Optional accessory by model ) : The voltage can be adjusted manually.
• Dual Voltage (Optional) : Two kinds of voltage can be given.
4. Safe Running (Protection)
• MCCB (Molded Case Circuit Breaker) can be opened by Over Current automatically.
• The engine can be stopped by High coolant temperature / Low oil pressure automatically
• The engine can be stopped by Over speed .
• Engine stop system : Energized in Run mode
The engine can be stopped automatically in case of the following condition.
(1) Over speed, (2) High coolant temperature, (3) Low oil pressure, (4) Emergency button is pushed.
5. Various Generator Type
EGS Series Generator has 4 types.
(1) Bonnet & Soundproof type with Control panel and MCCB : For single operation at residential area
(2) Non Bonnet type with Control panel and MCCB : For single operation in the room
(3) Non Bonnet type with Engine control panel : For parallel operation in the room
* Typical Generator Type
Open type for Single operation
10-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
10-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
10-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
10-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
10-6
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 11
INDEX
ENGINES
CONTENTS
Features ..................................................................... 11-2
Specifications ............................................................ 11-3
Engine used in KOMATSU Machines ...................... 11-4
High Altitude Deration .............................................. 11-6
11-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Features ENGINES
High quality:
The Komatsu diesel engine is a true achievement of our total engine production system-from casting all the
way through machining processes using Komatsu-made machine tools to the final steps of assembly.
Proven reliability
The Komatsu diesel engine is matched with our heavy-duty construction equipment to create a powerful
combination of unbeatable performance and high durability.
Economical operations:
The Direct injection system and special fuel-minimizing design of Komatsu diesel engines provide maximum
economy. Low lubricant consumption is also a remarkable advantage.
Compact design:
Advanced design and an efficient production system make Komatsu diesel engines compact and lightweight,
enhancing their versatility.
Low-noise operation:
Ideal designs keep engine noise and vibration to a minimum.
Wider applications:
A wide range of optional equipment offers a variety of applications to meet specific customer requirements.
Low emission engine:
Komatsu engine meets the emission regulations of North America, Europe, Japan, etc. by employing the
advanced technologies. The followings are examples of the technologies.
High-pressure injection system
Fuel is sprayed more finely to prevent increase of NOx and particulate matter by heightening the fuel
pressure injected into the cylinder.
Air-cooled aftercooler
Intake air temprature pressurized by the turbocharger is lowered largely by the air-cooled aftercooler
having high cooling capacity to prevent increase of NOx caused by high combustion temperature and
increase the intake air density for less fuel consumption.
Optimized shape of combustion chamber by use of FCD piston
The shape of the combustion chamber is optimized by employing an FCD piston having high strength and
the air flow speed is heightened by improving the shape of the air intake passage. With these
technologies, particulate matter is reduced.
Air-cooled aftercooler
High-pressure fuel
injection pump
Fuel accelerating
FCD piston
Optimize swirling
of intake air
11-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Specifications ENGINES
11-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
11-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
11-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
NOTE: (1) The percentages listed above are for standard machines.
(2) These values at each altitude range indicate the percentage of the horsepower obtained at the
sea level after fuel re-adjustment against rated flywheel horsepower.
100 percent means that no fuel re-adjustment is required.
(3)*: With automatic altitude deration.
(4)**: UK source
11-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
NOTE: (1) The percentages listed above are for standard machines.
(2) These values at each altitude range indicate the percentage of the horsepower obtained at the
sea level after fuel re-adjustment against rated flywheel horsepower.
100 percent means that no fuel re-adjustment is required.
(3) *: With automatic altitude deration.
11-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 12
INDEX
TIRES
CONTENTS
Tire classifications ....................................................12-2
Tire manufacturer's designation ..............................12-3
Tire designation:
Tire size designation ............................................12-5
Structure and function of tire ..............................12-5
Comparison of bias and radial tires ...................12-8
Tire selection .............................................................12-8
12-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
12-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
12-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
12-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Nowadays the ply rating shows the strength of the tire; it no longer shows the number of layers of cord
cloth. Originally the term "ply" did in fact refer to the number of layers of cord cloth, and was therefore an
indication of the tire strength. But with the development of new materials, the original cotton cord cloth
changed first to rayon and has now been replaced by nylon or steel wire.
This has made it possible to greatly increase the strength without increasing the number of layers of
material. Consequently the term "ply rating" has come to be used to indicate the strength of the tire rather
than to express the actual number of plies.
Stars (*,**,***) are used to indicate the strength of radial tires.
b) Breaker
Extra layers of rubber-coated cord are placed
between the outer plies and the tread. They
prevent cuts reaching the ply cords through tread,
and absorb shocks.
c) Plies
A tire is composed of several layers of plies,
coated on both sides by a rubber compound.
These maintain inflation pressure of the tires
supporting load. These plies are made of high
tensile nylon cord.
The term "Ply Rating", according to the Tire and Rim Association (TRA), is defined as follows:
"A given tire with its maximum recommended load when used in specific type service. It is an index of tire
strength and does not necessarily represent the number of cord plies in the tire."
d) Inner liner
The inner liner is a rubber layer covering the inside from bead to bead of a tubeless tire, corresponding to
the tube of an ordinary tube tire. It prevents the loss of inflation pressure of the tire.
12-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
e) Beads
Beads are the parts which fix the tire to the rim. All plies are tied into bundles of steel wire. The beads fit on
the rim perfectly, preventing the tire from slipping out of the rim contour while the vehicle is in motion.
g) Side-walls
Side-walls are covers made of a flexible rubber compound to protect the sides of the tire. Side-walls are
designed to cushion the plies from shocks and cuts, and to flex and bend without cracking, under ordinary
usage.
12-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
12-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
The carcass cord faces in a radial direction (at The carcass cord faces at bias (angle to the
Carcass 90' across the tire). tire).
• Several plies are placed on top of each
• There is one layer (ply) other and at an angle to each other.
Only a single ply is used, so the side wall is
Side wall flexible. The plies are placed on top of each other at
• To improve the resistance of the side wall to an angle, so the side wall is thick.
cuts, the carcass is turned up.
A breaker is used to protect the carcass and
To distribute the load around the to prevent the tread and carcass from
Tread circumference there is a steel belt layer which separating (Normally, a nylon breaker is used.
gives the tread high rigidity. Steel breakers are not suited for high speed
travel.)
There are multiple plies, so there are also
Bead Single bead structure multiple beads. (For dump trucks, there are
normally three).
Tire inflation Because of the structure of the tire, the
inflation pressure is higher than with bias Normally 5 - 7 kg/cm2
pressure tires.
12-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Increase in size
Inflation pressure
TKPH
(Heat resistance)
Depth of groove
Tread rubber
Speed Structure
Inflation pressure
Flotation
Wide base tire
Tire chain
Cost
(economy)
2. Tread pattern
The tread pattern can be divided broadly into the type in Fig. 1, which has no circumferential groove in the
tread center, the type in Fig. 2, which has transversal grooves, and the type in Fig. 3, which has a block
pattern. Generally speaking, the first type provides excellent resistance to cutting and wear, while the
second type provides excellent traction on slippery surfaces. The block pattern is typical of radial tires
giving good all round performance.
12-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
3. TMPH
The primary task of heavy-duty tires is to haul heavy loads faster and over longer distances. This heavy
load hauling inevitably results in heat built-up inside the tires, and tires have limitation of temperature.
If this limitation is reached, deterioration of the tire will begin at an early stage of operation. Accordingly, it
is necessary when selecting tires, to determine the amount of work will keep the tire within a safe range to
avoid over-heating when a vehicle is operated under given conditions.
The amount of work done under the given conditions and within a safe range is shown as the "TON-MILE-
PER-HOUR" which can be determined by the following formula:
Average tire load = 1/2 (tire load when vehicle carries no load + tire load when vehicle is loaded)
round trip distance × number of job cycles per day
Average speed = total hours of operation per day
4. Tire characteristics
The optimum tires should be selected for their applicable operation or job and terrain conditions depending
on the cutting (wear) resistance and heat resistance. These resistant qualities are indicated as follows:
12-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Because of the structure and quality of the rubber used for the tread, cut resistance and wear resistances
are mutually opposite to heat resistance, so when selecting tires, always check the TKPH.
Depending on the tire, super heat-resistant (SHR) and super cut-resistant (SCR) tread rubber are
available, so ask your tire distributor for details of tires that are not listed in the operation manual.
Radial Travelability
Suitable
tire (traction, flotation)
Bias Riding comfort
Initial
cost
Cost
Operating
cost
6. Correct Usage
1) Load on tire
If the tire is used with a load that exceeds the limit
for the tire, there will be excessive deformation of
the tire and generation of heat, and this may lead
to various types of damage.
Always keep to the load specified for the
machine, and ensure that there is no overload.
12-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
7. Tire life
See page 17-15.
12-12
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 13
INDEX
SPECIAL APPLICATION
RECOMMENDATION
CONTENTS
Introduction ...............................................................13-2
Recommendation for low grade fuel usage ............13-3
Recommendation for sandy and
dusty terrain condition ......................................13-4
Recommendation for high altitude ..........................13-5
Recommendation for cold and
extremely cold weather area .............................13-7
Tropical weather specification .................................13-9
13-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
In this chapter, why such special care is necessary and what are in the special spec are explained with
typical examples.
It is recommended to consult KOMATSU through the distributor for actual choice of a spec for such special
application.
North Pole
(4)
(2) (3)
13-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
1) Dirt
Since dirt in the fuel clogs the filter quickly, it can lower the engine power. In addition, it can lower
circulation of the fuel and wear the internal parts of the injection pump quickly. To solve this problem, a
filter of finer mesh should be used or the number of filters should be increased.
(Additional fuel filter for low grade fuel)
Fuel tank
Feed Injection
pump pump
Komatsu Engine P
Larger capacity
main filter
Fuel tank Return
PT pump
Cummins
Engine P
2) Water
Water in fuel rusts the fuel piping. In addition, it lowers lubrication performance, and that wear the sliding
parts of the injector, injection pump, etc. To solve this problem, a water separator should be installed.
Water Separator
Point: Fuel-water separator to be installed when there are water
contamination (>0.1%) risks due to poor fuel storage or
environmental factor
Types of Fuel Pump Installation Positions
Fuel tank
Feed pump
To injection
Injection pump pump
(Komatsu Engine) Filter
Fuel tank
PT pump To PT
(Cummins Engine) pump
Water separator
3) Sulfur
If fuel contains sulfur, sulfuric acid is produced and it accelerates internal corrosion. If it is obliged to use
fuel containing sulfur by 0.5% or more, use high TBN (Total Base Number) oil.
If fuel containing sulfur is used, the oil is deteriorated quickly and it should be replaced at shorter intervals.
For detail, see MAINTENANCE in the Operation & Maintenance manual.
13-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
2) Cyclone-type pre-cleaner
While the dust accumulated in the conventional US pre-cleaner must be removed by hand, the dust
swirled and sucked into TURBO-II and Enginaire (as example) are discharged automatically by a
centrifugal force.
Pre-creaner
(Example)
Engine hood
FVBH0291
TURBO-II Enginaire
(Example)
The air cleaner element must be replaced with new one after it is cleaned 6 times. If this new indicator is
used, however, the air cleaner element can be replaced according to its clogging condition. As a result,
the maintenance cost can be reduced.
13-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
1) The fuel injection rate must be reduced to secure a proper air-fuel ratio for combustion. If a mechanical
injection pump is employed, it must be readjusted mechanically. If fuel is controlled electronically, the
software of the engine controller must be changed.
2) Turbocharger
1) The turbocharger may need to be replaced with one equipped with an over-speed prevention device.
2) The turbocharger may need to be replaced with a water-cooled one to prevent shortening of its lifespan
caused by high temperature.
(Example: Water-cooled turbocharger)
Oil
Water (coolant)
Quick-release valve
Pressure reducing
valve
Hydraulic tank
pressure switch
13-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
(1) (2)
(3)
FVBH0299
FVBH0292
3) Pressurization of radiator
The radiator cap is replaced to
prevent lowering of boiling
point at high altitude.
13-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
(Example) D275A-5 with extremely cold weather specification (cold weather specification for CIS)
1) Warmth keeping for easy engine start
Cylinder Block
1500W x 1
Receptacle
Engine Oil Pan Power Train Oil Pan Outside electric power
600W x 1 600W x 2
Battery
C200 x 2
Portable Rocket
Heater 30000 Kcal/h
13-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
13-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
4) Heat-resistant alternator
PTO
Cooler
FVBH0293
13-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
MEMO
CONTENTS
SECTION 14
INDEX
SECTION 14A
PRODUCTIVITY
CONTENTS
Calculation of production ..................................... 14A-2
Bulldozers ............................................................... 14A-4
Dozer shovels & Wheel loaders ............................ 14A-6
Hydraulic excavators ............................................. 14A-9
Off-highway dump trucks .................................... 14A-13
Motor graders ....................................................... 14A-20
Soil compactors ................................................... 14A-21
Trash compactors ................................................ 14A-22
14A-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
PRODUCTIVITY
Calculation of production
When planning mechanized projects, one extremely important issue is how to calculate the production of the
machines.
The first step when estimating the production is to calculate a theoretical value as explained below. This
theoretical value is then adjusted according to actual figures obtained from past experience in similar
operations.
On the basis of these figures (particularly those for job efficiency) it will be possible to determine values
suitable for the project which will be neither over-optimistic nor wasteful.
Therefore it is first necessary to fully understand the theoretical calculations and to be able to obtain a figure
for working efficiency which is feasible on that job site.
From this it is possible to obtain a realistic figure for the work volume that can be attained.
60
Q= q × N × E = q × ×E
Cm
Example:
1,000 m3 of unexcavated earth has to be hauled.
a) What will its volume be when it has been excavated ready for hauling?
b) What will its volume be if it is then compacted?
Earth volume
conversion factor (f)
14A-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
PRODUCTIVITY
Job efficiency depends on many factors such as topography, operator's skill, and proper selection and
disposition of machines. Time out of an hour machine use is actually used.
It is very difficult to estimate a value for job efficiency due to the many factors involved. Therefore, efficiency
is given in the following section as a rough guide.
14A-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
Bulldozers PRODUCTIVITY
BULLDOZERS
(DOZING)
The hourly production of a bulldozer when excavating or dozing can be obtained by using the following
fomula:
60
Q=q× ×e×E
Cm
where Q : Hourly production (m3 /hr; yd3/hr) q : Production per cycle (m3; yd3)
Cm : Cycle time (in minutes) e : Grade factor
E : Job efficiency
When calculating the standard productivity of a bulldozer, the figure used for the volume of earth hauled in
each cycle, was taken as blade capacity. In fact, production per cycle differs with the type of soil, so the blade
fill factor is used to adjust this figure. See Table 2 to select the factor.
D D
Cm (min.) = + +Z
F R
14A-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
Bulldozers PRODUCTIVITY
(RIPPING)
Ripping production varies greatly according to such conditions as the properties of the rock, the method of
operation, and the operator's skill. Therefore, it is difficult to estimate. However, from available data, the
relationship as shown on the ripper section can be seen between seismic velocity and production.
QR × QD
Q=
QR + QD
14A-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
60
Q=q× ×E
Cm
where Q : Hourly production (m3 /hr; yd3 /hr) q : Production per cycle (m3; cu.yd3)
Cm : Cycle time (min.) E : Job efficiency
q = q1 × K
FVBH0048
14A-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
Table 5 Average cycle time for wheel loader Table 6 Average cycle time for dozer shovel
Unit: min. Unit: min.
Bucket size 3.1 ~ Bucket size 3.1 ~
Loading ~3m 3
5 m3 5.1 m ~3
Loading ~3m 3
5 m3
conditions conditions
A Easy 0.45 0.55 0.65 A Easy 0.55 0.60
B Average 0.55 0.65 0.70 B Average 0.60 0.70
C Rather difficult 0.70 0.70 0.75 C Rather difficult 0.75 0.75
D Difficult 0.75 0.75 0.80 D Difficult 0.80 0.80
Table 7 Average cycle time for wheel loader Table 8 Average cycle time for dozer shovel
Unit: min. Unit: min.
Bucket size 3.1 ~ Bucket size 3.1 ~
Loading ~ 3 m3 5 m3 5.1 m3 ~ Loading ~ 3 m3 5 m3
conditions conditions
A Easy 0.40 0.50 0.60 A Easy 0.55 0.60
B Average 0.50 0.60 0.65 B Average 0.60 0.70
C Rather difficult 0.65 0.65 0.70 C Rather difficult 0.75 0.75
D Difficult 0.70 0.75 0.75 D Difficult 0.80 0.80
The following table gives typical job efficiency as a rough guide. To obtain the actual production figure,
determine the efficiency in accordance with actual operating conditions.
60 × E
Q=q×
Cm
where Q : Hourly production (m3/hr; yd3/hr) q : Production per cycle (m3; yd3)
Cm : Cycle time (min.) E : Job efficiency
q = q1 × K
14A-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
D D
Cm = + +Z
1000VF 1000VR
60 60 Hauling distance
FVBH0050
Where D : Hauling distance (m, yd) VF : Travel speed with load (km/hr; MPH)
VR: Return speed (km/hr; MPH) Z : Fixed time (min)
Speed km/hr(MPH)
Operation conditions
Loaded Empty
Hauling on well compacted flat road, few bumps in road surface, no 10 ~ 23 11 ~ 24
Good
meeting other machines, can concentrate on L & C. (6.2 ~ 14) (6.8 ~ 15)
Average Few bumps on road surface, flat road, some auxiliary work carrying 10 ~ 18 11 ~ 19
large lumps of rock. (6.2 ~ 11) 6.8 ~ 12)
10 ~ 15 10 ~ 16
Rather poor Bumps in road surface, high rate of auxiliary work. (6.2 ~ 9.3) (6.2 ~ 10)
Large bumps in road, meeting other machines, difficult to carry out 9 ~ 12 9 ~ 14
Poor
smooth work, large amount of auxiliary work. (5.6 ~ 7.5) (5.6 ~ 8.7)
Z= t1 + t2 + t3 + t2
14A-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
HYDRAULIC EXCAVATORS
(CONSTRUCTION APPLICATION)
3600
Q=q× ×E
Cm
where Q : Hourly production (m3 /hr; yd3 /hr) q : Production per cycle (m3; yd3)
Cm : Cycle time (sec.) E : Job efficiency
q = q1 × K
14A-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
However, here we use cycle time = (standard cycle time) × (conversion factor)
The standard cycle time for each machine is determined from the following table.
Table 11 Standard cycle time for backhoe Unit: sec
Range Swing angle Range Swing angle
Model 45° ~ 90° 90° ~ 180° Model 45° ~ 90° 90° ~ 180°
PC60 10 ~ 13 13 ~ 16 PC240 15 ~ 18 18 ~ 21
PC100 11 ~ 14 14 ~ 17 PC270 15 ~ 18 18 ~ 21
PW100, PW130ES 11 ~ 14 14 ~ 17 PC300, PC350 15 ~ 18 18 ~ 21
PC120, PC130 11 ~ 14 14 ~ 17 PC380 16 ~ 19 19 ~ 22
PC160 13 ~ 16 16 ~ 19 PC400, PC450 16 ~ 19 19 ~ 22
PW170ES 13 ~ 16 16 ~ 19 PC600 17 ~ 20 20 ~ 23
PC180 13 ~ 16 16 ~ 19 PC750 18 ~ 21 21 ~ 24
PC200, PC210 13 ~ 16 16 ~ 19 PC800 18 ~ 21 21 ~ 24
PW200, 220 14 ~ 17 17 ~ 20 PC1250 22 ~ 25 25 ~ 28
PC220, PC230 14 ~ 17 17 ~ 20 PC1800 24 ~ 27 27 ~ 30
14A-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
(MINING APPLICATION)
The production for Mining Shovels shuld be calculated on loaded trucks per hour
Hourly production = loaded truck per hour x truck capacity x time utilisation
Qh = Tn x Tq x E
Theoretical loaded trucks per hour = 3600 sec/(Loading time per truck + spotting time per truck)
Tn = 3600/(tT + tsp)
Loading time per truck = (truck size/bucket capacity) rounded x cycle time
tT = (Tq/(Bc x K x loose density)) rounded x tc
Gh = hourly production (ton/hr; US ton/hr)
Tn = number of loaded trucks per hour
Tq = truck capacity (ton; US ton)
E = time utilisation per hour (%)
tT = truck loading time (sec)
tsp = truck spotting time (sec)
Bc = bucket capacity (m3; cu.yd)
K = bucket fill factor (%)
tc = cycle time (sec)
Yearly production = (hours per year - service hours) x availability x mine efficiency
QY = Qh x (hy - hs) x Sa x M
QY = yearly production
hy = theoretical hours per year (hr)
hs = service hour per year (hr)
Sa = mining shovel availability (%)
M = mine efficiency (%)
14A-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
(1) Backhoe
Digging conditions
Model Backhoe application
Easy Average Severe
PC1400 23 ~ 25 26 ~ 28 29 ~ 31 • Truck on lower level
PC3000 23 ~ 25 26 ~ 28 29 ~ 31 • Average swing 45°
PC4000 23 ~ 26 27 ~ 29 30 ~ 32
PC5500 24 ~ 27 28 ~ 30 31 ~ 33
PC8000 25 ~ 28 29 ~ 31 32 ~ 34
Digging conditions
Model Backhoe application
Easy Average Severe
PC1400 32 ~ 35 36 ~ 38 39 ~ 41 • Truck on upper level
PC3000 32 ~ 35 36 ~ 38 39 ~ 41 • Average swing 120°
PC4000 33 ~ 36 37 ~ 39 40 ~ 42 • Optimized working depth 4-5 m
PC5500 34 ~ 37 38 ~ 40 41 ~ 43 (13'1"–16'5")
PC8000 35 ~ 38 39 ~ 41 42 ~ 44
Digging conditions
Model Backhoe application
Easy Average Severe
PC1400 26 ~ 29 30 ~ 32 33 ~ 35 • Split bench application
PC3000 26 ~ 29 30 ~ 32 33 ~ 35 • Average swing 90°–120°
PC4000 27 ~ 30 31 ~ 33 34 ~ 36
PC5500 28 ~ 31 32 ~ 34 35 ~ 37
PC8000 29 ~ 32 33 ~ 35 36 ~ 38
(2) Front shovel
Digging conditions
Model Front shovel application
Easy Average Severe
PC1400 24 ~ 26 27 ~ 29 30 ~ 32 • Truck on same level
PC3000 24 ~ 26 27 ~ 29 30 ~ 32 • Average swing 60°
PC4000 24 ~ 27 28 ~ 30 31 ~ 33
PC5500 25 ~ 28 29 ~ 31 32 ~ 34
PC8000 26 ~ 29 30 ~ 32 33 ~ 35
14A-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
OFF-HIGHWAY DUMP TRUCKS
When carrying out operations using a suitable number of dump trucks of suitable capacity to match the
loader, the operating efficiency is calculated in the following order:
D D
Cmt = n x Cms + + t1 + + t2
V1 V2
(1) (2) (3) (4) (5)
(1) : Loading time
(2) : Hauling time
(3) : Dumping time
(4) : Returning time
(5) : Spot and delay time
1) Loading time
The time required for a loader to load a dump truck is obtained by the following calculation.
Loading time = Cycle time (Cms) × No. of cycles to fill dump truck (n)
14A-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
b) Number of cycles required for loader to fill dump truck full (n)
The payload of a dump truck depends on its capacity or weight.
* The bucket capacity and the body capacity, as a general rule, refer to heaped capacity but may be used
to refer to struck capacity depending on the nature of materials to be handled.
* The bucket fill factor is determined by the nature of soil to be excavated or loaded. In case of dozer
shovels or wheel loaders, a suitable factor can be selected from among those given in Table 3, 9, 10
according to the applicable loading condition.
14A-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
Fig. 1 KOMATSU HD325 Dump Truck Travel Performance Curve
The maximum speed thus obtained is a theoretical value, and in order to convert this maximum speed to a
practicable average speed, the speed should be multiplied by a speed factor. An applicable speed factor can
be selected from the following table.
The above average speed is applicable in ordinary driving conditions. If there is any factor retarding the
vehicle speed, an applicable factor should be used.
14A-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
c) Hauling time
If the hauling distance in each section is divided by the average speed given in the preceding
paragraph, the hauling time in each section will be obtained. If all of these times (for hauling and
returning) are added together, they will give the total hauling and returning time.
3) Dumping time
This is the period from the time when the dump truck enters the dumping area, to the time when the dump
truck starts its return journey after completing the dumping operation. The length of the dumping time
depends on the operating conditions, but average dumping times for favorable average and unfavorable
conditions are given by the following table.
However, particularly adverse conditions giving rise to extremely long dumping times are excluded.
4) Time required for the truck to be positioned and for the loader to begin loading.
The time taken for the truck to be positioned and
Operating conditions t2, (min.)
for the loader to begin loading also depends on
the operating conditions. As a general rule, a Favorable 0.1 to 0.2
suitable time can be selected from the table at Average 0.25 to 0.35
right. Unfavorable 0.4 to 0.5
As has so far been described, the cycle time of a
dump truck can be estimated by using the values
for factors obtained according to paragraph 1) to
4).
14A-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
2. Estimating the number of dump trucks required (M)
The quantity of dump trucks required for use in combination with a loader working at its maximum
operating efficiency can be estimated by the following formula:
The total hourly production P of several dump trucks where they are doing the same job simultaneously is
estimated by the following formula:
60
P=C × × Et × M
Cmt
Table 16 gives typical job efficiency as a rough Table 16 Job efficiency of dump truck (Et)
guide.
Operating conditions Job efficiency
To obtain the actual production figure, determine
the efficiency in accordance with actual operating Good 0.83
conditions. Average 0.80
Rather poor 0.75
Poor 0.70
When dump trucks and loaders are used in combination, it is most desirable that the operating
capacity of the dump trucks be equal to that to the loaders. That is, conditions satisfying the
following equation are most desirable. Consequently, if the value of the left equation is larger, the
group of dump trucks has a surplus capacity. On the other hand, if the value of the right equation is
larger, the group of loaders has a surplus capacity.
× Et × M x q1 × K ×
60 60
C× × Es
Cmt Cms
The left equation has already been described. The right equation has the following meaning.
14A-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
EXAMPLE
• A HD325, working in combination with a WA600, is hauling excavated material to a spoil-bank
500 meters away.
What is the hauling capacity of the HD325?
n is taken to be 4.
Loaded weight :
Weight when loaded = n × bucket capacity × bucket fill factor × loose specific gravity × 1,000
= 4 × 5.4 m3 × 0.9 × 1.6 × 1,000 = 31,104 kg
Using the Travel Performance Curve and Brake Performance Curve, the maximum speed for each
section can be calculated.
The values for HD325 can be calculated from PERFORMANCE CURVE on the section 7A.
14A-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
Off-Highway PRODUCTIVITY
Dump Trucks
The result is shown in the table below and the table of Hauling time and Returning time is 3.00 min.
60 60
P=C × × Et = 19.44 × × 0.83 = 137.3 m3/h
Cmt 7.05
14A-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
MOTOR GRADERS
The motor grader is used for many purposes such as maintaining roads, final finishing for earthmoving
projects, trenching and bank cutting.
Therefore there are many methods of expressing its operating capacity.
NOTE: Graders usually operate on long stretches, so the time required for gear shifting or turning can be
ignored.
N×D
T= V×E
14A-20
AH_25.book Page 21 Tuesday, March 23, 2004 9:41 AM
Compactors PRODUCTIVITY
W
N= × n
Le – Lo
SOIL COMPACTORS
There are two ways of expressing the productivity of compactors: by the volume of soil compacted, and by
the area compacted.
W × V × H × 1000 × E
Q=
N
Where
Q = Hourly production (m3/hr)(volume of soil compacted)
V = Operating speed (km/hr)
W = Effective compaction width per pass (m)
H = Compacted thickness for one layer (m)
N = Number of compaction (number of passes by compactor)
E = Job efficiency
14A-21
AH_25.book Page 22 Tuesday, March 23, 2004 9:41 AM
Compactors PRODUCTIVITY
W
N= × n
Le – Lo
TRASH COMPACTORS
There are two ways of expressing the productivity of compactors: by the volume of trash compacted, and by
the area compacted.
W x V x H x 1000 x γ
Q=
N
Where
Q = Hourly production (ton/hr)(volume of trash compacted)
V = Operating speed (km/hr)
W = Effective compaction width per pass (m)
H = Compacted thickness for one layer (m)
N = Number of compaction (number of passes by compactor)
γ = Compacted trash specific gravity (ton/m3)
14A-22
AH_25.book Page 23 Tuesday, March 23, 2004 9:41 AM
Compactors PRODUCTIVITY
2. Example
Hourly production of the work having following conditions is calculated:
Conditions
Machine: WF450T-3, WF550T-3, WF650T-3
Compacted thickness for one layer: H = 0.6 m
No. of Compaction: N=5
Compacted trash specific gravity: γ = 0.5 ton/m3
Estimating the production of trash compactors
WF450T-3 WF550T-3 WF650T-3
1 141 156 181.8
2 282 312 363.6
3 423 468 545.4
4 564 624 727.2
5 705 780 909
6 846 936 1090.8
7 987 1092 1272.6
1400
1200
Production (ton/hr)
1000
WF450T-3
800
WF550T-3
600
WF650T-3
400
200
0
0 2 3 4 5 6 7
14A-23
AH_25.book Page 24 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
SECTION 14B
EARTHMOVING
DATA
CONTENTS
Soil classification ................................................... 14B-2
Hauling performance of
construction machines:
Introduction ........................................................ 14B-4
Inherent machine capability ............................. 14B-4
Elements limiting the inherent
machine capability ......................................... 14B-5
Machine capabilities required
for earthmoving operations ......................... 14B-7
Summary and application ................................. 14B-9
Traffic-ability .................................................... 14B-11
Machines and site planning ................................ 14B-12
14B-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Rather, attention is required to be given to whether the soil to be handled is of special ores or contains special
clay minerals.
Hereinafter is described the knowledge necessary for earth work planning prior to such operations as
digging, loading, hauling, pushing (spreading), rolling compaction, etc., on ordinary terrain.
* Data (figures) to be given hereinafter vary largely depending on various operating and environmental
conditions. Consequently, before starting the earth work, tests should be conducted to obtain correct
data for operations.
Some knowledge of the weight data per unit volume of materials of their major ingredients is important for
their handling or hauling in mines, etc.. The specific weight data of some major types of soil and ingredients
are given below.
14B-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
14B-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
INTRODUCTION
"What Model or type of a tractor is most suitable to pull this trailer?" "Is this bulldozer capable of going up this
hill while pulling that scraper loaded full?"
In order to give explicit answers to these questions, it is necessary to have the right understanding of the
hauling performance of vehicles.
For easy understanding, let us explain the hauling performance with the following machine capabilities and
related elements.
a) Output power
The engine horsepower of a construction machine is the most essential power of those developed by the
machine itself. This can be estimated by multiplying one element (traction force) by another element (a
travel speed). Accordingly, where the engine of a machine develops a rated power; the smaller the travel
speed, the larger the traction force or drawbar pull will be. On the contrary, the larger the travel speed, the
smaller the drawbar pull.
b) Gear-shifting
Gear-shifting is effected to determine the optimum drawbar pull and travel speed required for
accomplishing a given job. Therefore, a machine has several gears to be selected by shifting for the
optimum travel speed.
The table below gives the drawbar pull and travel speeds of a direct-drive type bulldozer.
14B-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
converter. 40 440 44
320 32 F1
28
hauling performance is indicated by curves. The 280 28
graph at right gives the hauling performance 24
240 24
curves of the TORQFLOW-drive type bulldozer. 20
200 20
16 F2
160 16
12
120 12
8 80 8 F3
4 40 4
0 0 0
0 2 4 6 8 10 12 14 16 18 20km/h
0 2 4 6 8 10 12 MPH
Travel speed
1. What are the elements limiting the inherent machine capability or power? These are;
a) Traction between the undercarriage (tracks or wheels) and the road surface.
b) Altitude
Altitude in b) will be described in a separate issue and herein is examined the problem of traction
between the undercarriage and the road surface.
"When a motor vehicle cannot be moved due to slipping on the snow-covered road, what should be done
to move the vehicle?"
The answers are;
Solution Reason
(1) Add load to the driving wheels.
⇒The traction force is increased with the added
load.
(2) Install chain to the wheel tires or replace
the tires with the spiked type. ⇒The undercarriage is made so as to develop more
traction.
⇒
(3) Scatter sand or spread straw mats on the The critical traction force is increased by the
road surface. higher coefficient of traction.
The above facts can also be applied to a crawler tractor. Now, let us look at the coefficient of cohesion and
the critical traction force or traction used in the above table.
The critical traction is the maximum traction available depending on the cohesive condition of the road
surface. This can be estimated by the following formula.
14B-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Fd = µd•Gd
Where, Fd : Critical traction (kg)
µd : Coefficient of traction
Gd : Weight imposed on the driving wheels (kg)
The coefficient of traction depends on the condition of the road surface. Any applicable coefficient of
traction can be selected from among those given in the table below.
Weight to be imposed on the driving wheels can be determined by referring to the table below
Crawler type tractor 2-wheel drive machine 4-wheel drive machine
Weight imposed on
Total weight of tractor Total weight of tractor
the driving wheels
Example (1) Assume that the D155 tractor pulling a towed compactor must do compaction in a dry,
loose terrain. What is the critical drawbar pull?
Solution: The operating weight of the D155 tractor is 26730 kg. Then, Fd = 0.60 × 26730 = 16040 kg
Example (2) What are the values of the drawbar pull which the D50A-15 bulldozer can develop at F1
and F2 in a dry, loose terrain?
Solution: The operating weight of the D50A-15 bulldozer is 11400 kg. Its critical drawbar pull is
11400 × 0.60 = 6840 kg.
The rated drawbar pull indicated in its specifications is 8280 kg at F1 or 5920 kg at F2.
Consequently
at F1: The rated drawbar pull is 8280kg, but the tracks will start shoe slip at the
drawbar pull beyond 6840kg, making it impossible for its drawbar pull to be
utilized to the full. Thus, the critical drawbar pull practically available is 6840
kg.
at F2: The rated drawbar pull is 5920kg. Thus, the drawbar pull can be utilized to
the full.
14B-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
1. What are the elements limiting the machine capabilities required for earthmoving operations?
When a truck is traveling on the road or going uphill, the following phenomena will be encountered as a
matter of course.
2. Rolling resistance
When a vehicle is traveling on the ground or road, the retarding force of ground against wheels or tracks
should take place. Such a resistance varies depending on the ground or road surface conditions.
The rolling resistance is measured in the ratio to the vehicle weight and can be estimated by the following
formula.
Wr = µr•G
The coefficient of rolling resistance can be selected from among those given in the table below, according
to the ground or road surface conditions.
The coefficient of rolling resistance can be selected from among those given in the table below, according
to the ground or road surface conditions.
µr (%)
Type and conditions of ground Vehicle w/iron wheel Tractor w/pneumatic
treads Crawler tractor tires wheels
Iron truck 1.0
Concrete floor 2.0 2.8 2.3
Macadam road 2.9 3.3 2.8
Wood pavement 2.5
Dry unpaved plain road 4.5 4.6 3.5
Firm terrain 10.0 5.5 4.0
Dry, loose terrain 11.5 6.5 4.5
Soft terrain 16.0 8.0 9.0
Loose gravel 15.0 9.0 12.0
Loose sand 15.0 9.0 12.0
Muddy ground 12.0 16.0
Packed snow 3.7
Ice 2.0
In a crawler tractor, too, the rolling resistance should vary depending on the type of applied soil. The
representative values of rolling resistance, however, are taken into account in preparing the curves for
drawbar pull and hauling performance of crawler tractors. Therefore, the varying rolling resistance may
practically be ignored.
14B-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
Example (3) What is the rolling resistance of the D85-12 tractor to pull the RS12 scraper (empty).
The ground surface is in a soft terran.
Example (4) What is the rolling resistance of the D155 tractor to pull the RS24 scraper loaded full.
The ground surface is in a dry loose terran.
3. Grade resistance
The grade resistance is the retarding force of gravity to be encountered when a vehicle is going uphill.
The grade resistance can be estimated by the following formula.
Ws= G•sin α
a
Where, Ws : Grade resistance (kg) b
Ws
G : Operating weight of a vehicle (kg)
α : Angle formed with the horizon (degree) G
FVBH0041
A grade (degree) and sin α can be selected from among those given in the table below.
Example (5) What is the grade resistance against the D50A-15 angledozer going uphill at 15° ?
Solution: The operating weight of the D50A-15 angledozer is 11400 kg. Thus, the grade resistance
will be 11400 × 0.259=2950 kg
4. Hauling resistance
The hauling resistance is the grand total of the rolling resistance, grade resistance, accelerating resistance
and air resistance. However, construction machines are slow in the travel speed. Normally, the hauling
resistance of construction machines may be considered to be the total of the rolling resistance and grade
resistance.
The grade resistance acts so as to retard the uphill traveling of a vehicle, whereas the grade resistance
acts so as to accelerate the downhill traveling. The above relationships can be indicated as follows:
14B-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Example (6) What is the hauling resistance against the D60-6 tractor going uphill at 4° in a dry, loose
terrain, while pulling an RS08 scraper with maximum load?
Solution: The gross weight of the RS08 with maximum load is 18870 kg.
The rolling resistance factor is 0.045. Thus, the rolling resistance is 0.045 × 18870 = 850
kg
The weight of the D60-6 tractor is 12550 kg.
The gross weight of the RS08 is 18870 kg.
Then, the total weight of both machines is 31420 kg
Consequently, the grade resistance is 0.07 × 31420 = 2200 kg.
Thus, the hauling resistance is 850 + 2200 = 3050 kg.
2. Application
Example (7) Assume that the D65 tractor is used to pull a wheeled wagon (the empty weight: 17
tons) with a 50-ton load in a dry, loose terrain.
What are the operating gears and the corresponding approx. travel speeds available on
a flat, level ground? What is the degree of a hill climbable under the same condition?
14B-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
level ground
lb x 103
kN
200 44 20
approx. 9.0 km/h at F3 or
180 40 F1
approx. 6.0 km/h at F2
18
160 36
16
Drawbar pulI
32
140 14
28
120 12 F2
24
100 10
20
80 8
16
60 6
12
40 4 F3
8
20 4 2
0 0 0
0 2 4 6 8 10 12 14 km/h
0 2 4 6 8 MPH
Travel speed
Tractor weight + wagon weight + pay load = 12750 + 17000 + 50000 = 79750 kg
The grade resistance retarding per angle of grade is 79750 × 0.018 = 1435 kg
Consequently,
The explanations made so far on the travelling or hauling performance of construction machines pertain only
to the traveling of individual machines and the pulling of towed vehicles by tractors. For instance where a
tractor pulls a scraper, it can be judged whether the tractor can be used for this purpose, but it can not be
determined whether the tractor can perform a digging or a loading operation under the same conditions as
mentioned above. Operators or field-superintendents are requested to keep it in mind that such a judgement
should be based on the operators' accumulated experiment or on the reference for such operating
combinations or cooperation among towing tractors and towed vehicles as recommended by KOMATSU.
14B-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
Cone FVBH0042
14B-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
15 m (49'3") or less
bench width
14B-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
Ditch
Truck Truck
width width
Center
crearance (B)
Shoulder Shoulder
(A) (C)
Width in
use
Total
width
Center clearance (B) Downhill shoulder (A) Uphill shoulder (C) Total road width
Model Speed km/h (MPH)
m (ft.in) m (ft.in) m (ft.in) m (ft.in)
HD255-5 20 (12.4) 2.0 (6'7") 2.0 (6'7") 1.0 (3'3") 11.4 (37'5")
Truck width 30 (18.6) 2.5 (8'2") 2.0 (6'7") 1.5 (4'11") 12.4 (40'8")
3.2 m (10'6") 40 (24.9) 3.0 (9'10") 2.0 (6'7") 1.5 (4'11") 12.9 (42'4")
HD325-6 20 (12.4) 3.0 (9'10") 2.0 (6'7") 1.5 (4'11") 13.8 (45'3")
Truck width 30 (18.6) 3.0 (9'10") 3.0 (9'10") 1.5 (4'11") 14.9 (48'11")
3.7 m (12'2") 40 (24.9) 3.5 (11'6") 3.0 (9'10") 2.0 (6'7") 15.9 (52'2")
HD405-6 20 (12.4) 3.0 (9'10") 2.0 (6'7") 1.5 (4'11") 13.8 (45'3")
Truck width 30 (18.6) 3.0 (9'10") 3.0 (9'10") 1.5 (4'11") 14.9 (48'11")
3.7 m (12'2") 40 (24.9) 3.5 (11'6") 3.0 (9'10") 2.0 (6'7") 15.9 (52'2")
HD465-7 20 (12.4) 3.0 (9'10") 3.0 (9'10") 1.5 (4'11") 15.9 (52'2")
Truck width 30 (18.6) 3.5 (11'6") 3.0 (9'10") 2.0 (6'7") 16.9 (55'5")
4.2 m (13'9") 40 (24.9) 3.5 (11'6") 3.5 (11'6") 2.5 (8'2") 17.9 (58'9")
HD605-7 20 (12.4) 3.0 (9'10") 3.0 (9'10") 1.5 (4'11") 15.9 (52'2")
Truck width 30 (18.6) 3.5 (11'6") 3.0 (9'10") 2.0 (6'7") 16.9 (55'5")
4.2 m (13'9") 40 (24.9) 3.5 (11'6") 3.5 (11'6") 2.5 (8'2") 17.9 (58'9")
HD785-5 20 (12.4) 3.5 (11'6") 3.5 (11'6") 2.5 (4'11") 20.9 (68'7")
Truck width 30 (18.6) 4.0 (13'1") 4.5 (14'9") 2.5 (6'7") 22.4 (73'6")
5.7 m (18'8") 40 (24.9) 4.5 (14'9") 4.5 (14'9") 3.0 (8'2") 23.4 (76'9")
HD985-3 20 (12.4) 3.5 (11'6") 3.5 (11'6") 2.5 (8'2") 20.9 (68'7")
Truck width 30 (18.6) 4.0 (13'1") 4.5 (14'9") 2.5 (8'2") 22.4 (73'6")
5.7 m (18'8") 40 (24.9) 4.5 (14'9") 4.5 (14'9") 3.0 (9'10") 23.4 (76'9")
HD1200-1 20 (12.4) 3.5 (11'6") 3.5 (11'6") 2.5 (8'2") 22.1 (72'6")
Truck width 30 (18.6) 4.0 (13'1") 4.5 (14'9") 2.5 (8'2") 23.6 (77'5")
6.3m (20'8") 40 (24.9) 4.5 (14'9") 4.5 (14'9") 3.0 (9'10") 24.6 (80'9")
HD1500 20 (12.4) 3.5 (11'6") 3.5 (11'6") 2.5 (8'2") 22.7 (74'6")
Truck width 30 (18.6) 4.0 (13'1") 4.5 (14'9") 2.5 (8'2") 24.2 (79'5")
6.62 m (21'9") 40 (24.9) 4.5 (14'9") 4.5 (14'9") 3.0 (9'10") 25.2 (82'8")
14B-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
Center clearance (B) Downhill shoulder (A) Uphill shoulder (C) Total road width
Model Speed km/h (MPH)
m (ft.in) m (ft.in) m (ft.in) m (ft.in)
630E 20 (12.4) 3.5 (11'6") 3.5 (11'6") 2.5 (8'2") 22.8 (74'10")
Truck width 30 (18.6) 4.0 (13'1") 4.5 (14'9") 2.5 (8'2") 24.3 (79'9")
6.65 m (21'10") 40 (24.9) 4.5 (14'9") 4.5 (14'9") 3.0 (9'10") 25.3 (83'0")
730E 20 (12.4) 3.5 (11'6") 4.0 (13'1") 2.5 (8'2") 24.5 (80'5")
Truck width 30 (18.6) 4.0 (13'1") 5.0 (16'5") 2.5 (8'2") 26.0 (85'4")
7.25 m (23'9") 40 (24.9) 4.5 (14'9") 5.0 (16'5") 3.0 (9'10") 27.0 (88'7")
830E 20 (12.4) 3.5 (11'6") 4.0 (13'1") 2.5 (8'2") 24.5 (80'5")
Truck width 30 (18.6) 4.0 (13'1") 5.0 (16'5") 2.5 (8'2") 26.0 (85'4")
7.26 m (23'10") 40 (24.9) 4.5 (14'9") 5.0 (16'5") 3.0 (9'10") 27.0 (88'7")
930E-3 20 (12.4) 4.0 (13'1") 4.0 (13'1") 2.5 (8'2") 27.9 (91'6")
Truck width 30 (18.6) 4.5 (14'9") 5.0 (16'5") 2.5 (8'2") 29.4 (96'6")
8.69 m (20'6") 40 (24.9) 5.0 (16'5") 5.0 (16'5") 3.0 (9'10") 30.4 (99'9")
14B-14
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 15
INDEX
OWNING &
OPERATING COSTS
CONTENTS
Estimation of the owning and operating cost:
Owning cost ..........................................................15-2
Operating cost ......................................................15-4
Example .................................................................15-6
Application and operating conditions table .......15-9
Fuel consumption ...................................................15-10
Lubricant consumption ..........................................15-15
Tire life .....................................................................15-18
Optimum Fleet Recommendation (OFR)
software program ....................................................15-19
Komatsu information on reliability
and durability ..........................................................15-20
15-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
Along with the trend for mechanization adopted for economical and satisfactory job accomplishment,
equipment costs now occupy a large proportion of the overall construction cost. Therefore, the estimation of
the equipment costs has become more important. Success or failure in a contract for a construction job is
virtually dependent on the estimates of the equipment costs. In other words, careful consideration of the
equipment costs is of prime importance, if a contractor is to fulfill the contract at a profit. Unless estimates are
made properly, there will occur cases where a construction job cannot be accomplished at a profit.
1. OWNING COST
The equipment owning cost is the expense required, as a matter of course, for the purchase and
possession of the equipment as a property of its owner and consists of the following two items.
(1) Depreciation
(2) Interest, insurance and taxes
1-1.DEPRECIATION
In general, depreciation is a tax term referring to the legally permitted decline in value from the original
purchase price of equipment, and is an assessable property (expressed in units of years). Depreciation
referred to herein is a business practice for conserving the investment in the form of purchased
equipment, in other words, for making preparations in a systematic manner for the fund necessary for
replacing the existing equipment with new or any other equipment.
Net Depreciation Value
Depreciation = Depreciation Period in Hours
Net depreciation value means Original purchase price minus Resale or Trade-in price.
The depreciation period varies considerably according to the equipment operating conditions. It is also
affected by the speed of fund collection desired by the user, environmental and economic conditions in
its applied territory. Furthermore, it goes without saying that maintenance of equipment is a significant
15-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
Some users will hope that in terms of book value the machine will depreciate completely within the
depreciation period. Other users will hope that the residual value expressed as resale value or trade-in
value will be left. For these users the resale value or trade-in value is an important factor in reducing the
capital invested. This value is also a factor when deciding to purchase a new machine.
The resale value or trade-in value changes greatly according to the territory. Therefore the conditions in
that territory must be considered when determining these values. However, major factors in deciding
resale value or trade-in value are the hours of operation, nature of work and working environment. The
real resale value or trade-in value cannot be decided simply, but when a realistic value is decided it is
subtracted from the purchase price to give the Net Depreciation value. It is then possible to obtain the
depreciation from the Net Depreciation Value.
Insurance and taxes are imposed on the annual residual values of the equipment, which requires
knowledge of depreciation as prescribed by the tax law. The depreciation rate or the depreciation
period (whether it is a fixed amount or a fixed rate) vary according to the country. For the correct values
of insurance and taxes on the residual value in a country, the calculation formulas established in that
country must be used.
Interest, insurance and taxes are imposed on the residual value that is the difference between the
purchase price and the depreciated amount. This residual value decreases every year. However, when
the user calculates owning & operating costs, it is convenient to consider interest, insurance and taxes
as a constant amount paid out each year. For this reason, the machine will be considered here to
depreciate by a constant annual amount. A calculation is made of the average value of the residual
value at the beginning of each year within the depreciation period, and interest, insurance and taxes are
imposed on this value. By dividing this value by the number of hours the user expects to operate the
machine in one year, the hourly value can be calculated.
The annual rates are the total of those of interest, insurance and tax.
The factor can be obtained by using Table 1 or can be calculated by the following formula.
(n – 1) (1 – r)
Factor = 1 – 2n
15-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
(Example)
Delivered price: $100,000 Annual rates: 15% Annual use in hours: 2,000 hrs
Trade-in value: $25,000 Depreciation period (n) : 4 years
Solution Table 1 Factor of Interest,
Insurance, Taxes
25,000
r= = 0.25 n=1
100,000 1.0
(4 – 1) (1 – 0.25) 0.95
Factor = 1 – = 0.72
2×4 ye
ar
s
0.90 in
d
r io
pe
When obtaining the factor by using Table 1. n
tio =2
cia n
0.85 re
ep
Enter r = 0.25 in Table 1
)
:D 3
(n–1) (1–r)
n
n=
n=
0.72
0.65
2. OPERATING COST
8
n=
The equipment operating costs are proportional to the time that the 0.60
2-1. FUEL
More definite fuel consumption data should be measured in the field.
It is possible, however, to anticipate the actual or approximate consumption values according to the
actual operating conditions without measuring the consumption. Table 3 gives the hourly fuel
consumption values for KOMATSU construction machines. In this table, the average values are given,
provided that the job conditions are classified into three different ranges of application. If a user has
data on certain operating conditions, more correct or realistic values will be obtained by applying these
data in similar operating conditions, provided that the equipment is limited to the same type as that
used in the user's data.
To estimate hourly fuel cost, select the job condition based on application and find hourly fuel
consumption.
Hourly fuel cost = Hourly fuel consumption × Local unit price of fuel
2-2. LUBRICANTS (OIL AND GREASE), FILTERS AND PERIODIC MAINTENANCE LABOR
It is possible to measure the consumption of lubricants and grease in the same manner as the fuel
consumption. The consumption values of lubricants and grease are also obtained by calculation on the
basis of lubrication intervals, but they are affected greatly by the type of machines and their operating
conditions, which makes it difficult to specify the consumption suited for various machines and their
operating conditions. Hence, Table 4 gives the average consumption on the data obtained in the past,
which is available for your reference.
Prices of lubricants vary in countries or areas and, therefore, the local price (price in that country or
area) should be used.
In KOMATSU construction machines, filter replacement intervals are standardized for each machine
model. Thus, the cost of filter can be calculated from the local price of filter and the replacement
interval. The hourly filter cost is the total of the hourly costs for each type of filter.
15-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
2-3. TIRES
As has been described in Depreciation, tires are in the category of consumable parts and tires are
generally expensive. Therefore, it is better to include the tire cost as an individual item in the operating
costs. Tire cost is calculated by the following formula.
Tire price
Hourly tire cost = Estimated life
As tire prices vary in each country or area, the price of tires actually bought by a user should be applied.
It is difficult to indicate definitely the tire life, because the tire life is affected by many factors. However,
the general measurements for the life expectancy of tires can be indicated on the basis of past
experience and data obtained from the tire manufacturers. Refer to Table 4.
In this table, the approximate life values are given for three different types of conditions. The optimum
value for a certain ground condition is one of those obtained by a user in experience on similar ground
conditions. When recapped tires are to be used, their prices and life expectancy must be changed
correspondingly.
15-5
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
Applications:
Mass excavation or trenching where machine digs all the time in natural bed clay soils. Some traveling and
steady, full throttle operation.
Net Depreciation Value
Since the machine is a crawler-type, tires are not involved. This owner knows from experience that at trade-in
time, the machine will be worth approximately 10% of its delivered price 4 years from now.
Trade-in value is $9,281
Net depreciation value = $92,811 – $9,281 =$83,530
OWNING COST
Depreciation:
Putting 10,000 hours as the example depreciation period.
$83,530
Depreciation = 10,000 = $8.35
Calculate the Factor according to depreciation period and trade-in value rate, which is 0.66.
Enter the annual rates of interest, insurance and taxes and total them, which is 0.14 as an example.
0.66 × $92,811 × 0.14
Interest, insurance, taxes cost = = $3.43
2,500
Add up the depreciation cost and interest, insurance, taxes cost for total owning.
OPERATING COST
Fuel: See Table 3.
The intended application is in medium range. The estimated fuel consumption from table is 12.5 liter/hour.
Cost of fuel in this area is $0.2/liter.
Consumption × Unit cost = 12.5 liter/hr × $0.2/liter = $2.5
Repair Cost
Use local Komatsu distributor’s estimation. (For calulation example: use $3.30)
Repairs = $3.30
Since the machine does not have fast wear parts like ripper points of bulldozer or cutting edge of motor
grader, special item can be disregarded.
Operator hourly wage in this area is $16.00.
Add up the fuel cost, lubricant grease filter costs, repair cost and operator's hourly wage for operating cost.
15-6
AH_25.book Page 7 Tuesday, March 23, 2004 9:41 AM
15-7
AH_25.book Page 8 Tuesday, March 23, 2004 9:41 AM
15-8
AH_25.book Page 9 Tuesday, March 23, 2004 9:41 AM
Dozer shovels • Loading of light material • Continuous loading from • Bank excavation and
from stock pile with stock pile. loading.
substantial Idle time. • Light excavation and • Loading of blasted
loading. material.
Hydraulic excavators • Slope finishing, light • Mainly excavating and • Excavation of hard bank.
material digging, and loading.
other light-duty operation. • Breaker operation.
Motor graders • Finishing and other light- • Mainly road maintenance, • Maintenance or repair of
duty operations. repair and construction. hard surface road,
• Snow removal remarkable scarifying and
or ripping operation.
Wheel loaders • Loading of light material • Continuous loading from • Bank excavation and
from stock pile stock pile loading.
• Operation with substantial • Light-duty excavation and • Loading of blasted rock.
truck waiting time. loading.
Wheel dozers • Light surface finishing • Average surface finishing • Digging and dozing hard
• Spreading light material • Digging and dozing soft earth
earth
15-9
AH_25.book Page 10 Tuesday, March 23, 2004 9:41 AM
D61EX, PX-12 1.7 ~ 3.3 6.3 ~ 12.6 3.3 ~ 5.0 12.6 ~ 18.9 5.0 ~ 6.7 18.9 ~ 25.2
D65E, P-12 2.0 ~ 4.1 7.7 ~ 15.5 4.1 ~ 6.1 15.5 ~ 23.2 6.1 ~ 8.2 23.2 ~ 31.0
D65EX, PX-15 2.1 ~ 4.2 7.9 ~ 15.8 4.2 ~ 6.3 15.8 ~ 23.7 6.3 ~ 8.3 23.7 ~ 31.6
D85E-SS-2A 2.2 ~ 4.4 8.4 ~ 16.8 4.4 ~ 6.7 16.8 ~ 25.2 6.7 ~ 8.9 25.2 ~ 33.6
D85EX, PX-15 2.6 ~ 5.3 10.0 ~ 20.1 5.3 ~ 8.0 20.1 ~ 30.2 8.0 ~ 10.6 30.2 ~ 40.2
D155A-5 3.2 ~ 6.6 12.3 ~ 24.8 6.6 ~ 9.8 24.8 ~ 37.2 9.8 ~ 13.1 37.2 ~ 49.6
D155AX-5 3.4 ~ 6.7 12.7 ~ 25.5 6.7 ~ 10.1 25.5 ~ 38.2 10.1 ~ 13.4 38.2 ~ 50.9
D155A-2A 7.4 ~ 9.2 28 ~ 35 10.0 ~ 11.9 38 ~ 45 12.9 ~ 14.8 49 ~ 56
D275A, AX-5 8.0 ~ 11.3 30.2 ~ 42.7 11.3 ~ 14.6 42.7 ~ 55.3 14.6 ~ 17.9 55.3 ~ 67.9
D375A-5 10.2 ~ 14.4 38.5 ~ 54.5 14.4 ~ 18.7 54.5 ~ 70.6 18.6 ~ 22.9 70.6 ~ 86.6
D475A-5, -5SD 16.2 ~ 22.9 61.2 ~ 86.7 22.9 ~ 29.6 86.7 ~ 112.2 29.6 ~ 36.4 112.2 ~ 137.7
D575A-3 21.0 ~ 29.7 79.5 ~ 112.6 29.7 ~ 38.5 112.6 ~ 145.7 38.5 ~ 47.3 145.7 ~ 137.7
D575A-3SD 22.2 ~ 31.4 83.9 ~ 118.8 31.4 ~ 40.6 118.8 ~ 153.8 40.6 ~ 49.9 153.8 ~ 188.7
Low: Machine movement is mainly consisting of idle running or traveling unloaded.
Medium: Average earth moving, scraper hauling or easy pushing operation.
High: Ripping, heavy pushing, and operation continued without rest at full horsepower.
(2) Pipelayers
Range Low Medium High
Amount U.S. Gal/hr. ltr./hr. U.S. Gal/hr. ltr./hr. U.S. Gal/hr. ltr./hr.
Machine
D85C-1 2.4 ~ 3.2 9 ~ 12 3.4 ~ 4.2 13 ~ 16 4.2 ~ 5.0 16 ~ 19
D155C-1 3.4 ~ 4.5 13 ~ 17 5.3 ~ 6.3 20 ~ 24 6.9 ~ 7.9 26 ~ 30
D355C-3 4.2 ~ 5.3 16 ~ 20 5.8 ~ 6.9 22 ~ 26 7.4 ~ 8.5 28 ~ 32
15-10
AH_25.book Page 11 Tuesday, March 23, 2004 9:41 AM
15-11
AH_25.book Page 12 Tuesday, March 23, 2004 9:41 AM
15-12
AH_25.book Page 13 Tuesday, March 23, 2004 9:41 AM
15-13
AH_25.book Page 14 Tuesday, March 23, 2004 9:41 AM
(10) Compactors
Range Low Medium High
Amount U.S. Gal/hr ltr./hr U.S. Gal/hr ltr./hr U.S. Gal/hr ltr./hr
Machine
JV100 series — — — — — —
CONDITIONS:
Low: Light dozing and compacting.
Medium: Normal dozing and compacting.
High: Heavy dozing and compacting on heavy material.
15-14
AH_25.book Page 15 Tuesday, March 23, 2004 9:41 AM
15-15
AH_25.book Page 16 Tuesday, March 23, 2004 9:41 AM
* 10% of oil change volume between oil change intervals plus volume of oil change (latest every 6000 h)
** 2% of oil change volume between oil change interval (3000 h) plus volume of oil change
*** Including oil management system
15-16
AH_25.book Page 17 Tuesday, March 23, 2004 9:41 AM
15-17
AH_25.book Page 18 Tuesday, March 23, 2004 9:41 AM
The life varies with brand and material. Tires may be used above or below the tire life expectancy given in this
table.
15-18
AH_25.book Page 19 Tuesday, March 23, 2004 9:41 AM
Computer processing
Report contents
1. Production condition, object material, cost data
2. Optimum machine combination
3. Production
4. Number of units
5. Production cost
For Customer;
Please contact the nearest Komatsu distributor with your specific conditions, application and
requirements.
15-19
AH_25.book Page 20 Tuesday, March 23, 2004 9:41 AM
For Customer;
Please contact the nearest Komatsu distributor with your specific model, application and requirements.
15-20
AH_25.book Page 1 Tuesday, March 23, 2004 9:41 AM
CONTENTS
SECTION 16
INDEX
CONTENTS
Unit conversion tables ..............................................16-2
16-1
AH_25.book Page 2 Tuesday, March 23, 2004 9:41 AM
a. Length
Centimeter Meter (m) Inch (in) Foot (ft) Yard (yd) Mile (M) Kilometer
(cm) (km)
1 0.01 0.3937 0.03281 0.01094 1 1.6093
100 1 39.37 3.281 1.0936 0.6214 1
2.540 0.0254 1 0.8333 0.02778
30.48 0.3048 12 1 0.3333
91.44 0.9144 36 3 1
b. Space
Sq. meter (m2) Sq. Inch (in2) Sq. foot (ft2) Sq. yard (yd2)
1 1550 10.764 1.1960
0.036452 1 0.026944 0.037716
0.09290 144 1 0.11111
0.8361 1296 9 1
c. Volume
Cu. Cu. inch(in3) Cu. foot(ft3) Cu. Imperial Gal U.S. Gal Cu. Inch Liter
meter(m3) yard(yd3)
1 61024 35.31 1.3079 1 1.201 177.4 4.546
0.041639 1 0.035787 0.042143 0.8327 1 231 3.785
0.02832 1728 1 0.037037 0.023605 0.024329 1 0.01639
0.76455 46656 27 1 0.2200 0.2642 61.02 1
d. Weight
Kilogram (kg) Pound (lb) Metric Ton Short Ton Long Ton Newton (N)
(French Ton) (U.S. Ton) (English Ton)
1 2.2046 0.001 0.0011023 0.039842 9.80665
0.4536 1 0.034536 0.035 0.034464 4.448
1000 2204.6 1 1.1023 0.9842 9806.65
907.1 2000 0.9072 1 0.8929 8896.5
1016 2240 1.016 1.120 1 9964
0.10197 0.2248 0.031019 0.031124 0.031004 1
e. Pressure
f. Velocity
m/sec km/h ft/sec. MPH
1 3.6 3.281 2.237
0.2778 1 0.9113 0.6214
0.3048 1.097 1 0.6818
0.4470 1.609 1.467 1
16-2
AH_25.book Page 3 Tuesday, March 23, 2004 9:41 AM
g. Horsepower
PS HP kW kg.m/s kCal
1 0.986 0.736 75 0.1757
1.014 1 0.746 76.07 0.1782
1.3592 1.3405 1 101.97 0.2389
0.01333 0.01315 0.009807 1 0.002343
5.6902 5.611 4.186 426.9 1
h. Torque
kg.m ft.lb N.m
1 7.233 9.807
0.1383 1 1.356
0.1020 0.7375 1
i. Temperature
32°F = 0°C, –459.67°F = –273.15°C, 1°F = 0.5556°C
°F °C °F °C °F °C °F °C
–450 –267.78 5 –15.00 55 12.78 150 65.56
–400 –240.00 10 –12.22 60 15.56 200 93.33
–350 –212.22 15 –9.44 65 18.33 250 121.11
–300 –184.44 20 –6.67 70 21.11 300 148.89
–250 –156.67 25 –3.89 75 23.89 350 176.67
–200 –128.89 30 –1.11 80 26.67 400 204.44
–150 –101.11 35 1.67 85 29.44 450 232.22
–100 –73.33 40 4.44 90 32.22 500 260.00
– 50 –45.56 45 7.22 95 35.00 550 287.78
0 –17.78 50 10.00 100 37.78 600 315.56
°F 1 2 3 4 5 6 7 8 9
°C 0.556 1.111 1.667 2.222 2.778 3.333 3.889 4.444 5
Example: To convert 92°F into °C
90°F = 32.22°C, 2°F = 1.111°C, 90°F+2°F = 33.33°C
16-3
AH_25.book Page 4 Tuesday, March 23, 2004 9:41 AM
j. Angles of Gradient
o
45
= 100%
16-4
Index.fm Page 1 Friday, March 26, 2004 1:22 PM
INDEX
CONTENTS
A B
Air dryer ............................................................... 4A-38 Beads ..................................................................... 12-6
Altitude deration...................................................... 11-6 Bench height ........................................................2A-92
Angle dozer ........................................................... 1B-2 Blade accumulator................................................5A-18
Arm crowd force .................................................. 2A-73 Blade availability.....................................................1B-3
Asphalt debris........................................................ 8A-4 Blade fill factor.......................................... 1B-16, 14A-4
Asphalt-pavement profiling method ....................... 5D-3 Blade float ............................................................5A-19
Attachment availability Blade selection .......................................................1B-2
Motor graders ................................................... 5A-8 Body extension.....................................................4A-37
Wheel loaders............................................... 3A-105 Body liner .............................................................4A-37
Attachments of excavator Body selection ......................................................4A-42
Aqua-digger ....................................................... 2J-8 Bolt-on teeth ....................................................... 3A-111
Car scrap handler ........................................... 2D-10 Bolt-on cutting edge ........................................... 3A-111
Clamshell buckets............................................. 2D-3 Brake performance curve
Ditch cleaning buckets...................................... 2D-2 HD255-5 .......................................................... 4A-11
Power fork II.................................................... 2G-12 HD325-6 ..........................................................4A-13
High-mount cab ................................................. 2J-5 HD325-6 4WD .................................................4A-15
Hydraulic breaker.............................................. 2D-8 HD405-6 ..........................................................4A-17
Hydraulic crusher.............................................. 2G-8 HD465-7 ..........................................................4A-19
Hydraulic crusher & cutter ................................ 2G-6 HD605-5 ..........................................................4A-21
Lifting magnet ................................................. 2D-10 HD785-5 ..........................................................4A-23
Magnet fork..................................................... 2D-13 HD985-5 ..........................................................4A-27
Offset boom ...................................................... 2D-6 HD1200-1 ........................................................4A-29
Orange grapple............................................... 2D-13 HD1500-5 ........................................................4A-30
Ripper buckets.................................................. 2D-2 630E ................................................................4A-31
Road ripper ....................................................... 2D-7 730E ................................................................4A-32
Rotary log grapple ............................................ 2D-9 830E ................................................................4A-33
Scrap grapple ................................................. 2D-13 930E-2 .............................................................4A-34
Scrap handling machine ..................................2D-11 Breaker................................................................... 12-5
Single-shank rippers ......................................... 2D-2 Breakout force ....................................................3A-102
Slope finishing buckets ..................................... 2D-2 Bucket and arm combinations
Spike hammer................................................... 2D-6 Excavators, backhoes .....................................2A-74
Super long front ................................................ 2D-6 Wheel-type excavators .................................... 2F-10
Telescopic arm (box type)................................. 2D-4 Bucket capacity ..................................................3A-102
Telescopic arm (sliding type) ............................ 2D-4 Bucket capacity definition.....................................2A-71
Telescopic arm and 2-piece boom .................... 2D-5 Bucket capacity rating ..........................................2A-71
Three-shank rippers.......................................... 2D-3 Bucket digging force.............................................2A-73
Vibratory pile driver........................................... 2D-7 Bucket fill factor
Trapezoidal buckets.......................................... 2D-2 Excavators, backhoes ...................................2A-100
Attachments of motor grader Wheel loaders................................................3A-152
Front dozer blade............................................ 5A-12 Bucket features .................................................. 3A-110
Rear mounted ripper....................................... 5A-13 Bucket selection
Scarifier............................................................. 5A-9 Excavators, backhoes .....................................2A-72
Attachments of wheel loader Wheel loaders................................................ 3A-112
Dumping fork spec........................................ 3A-133 Bucket width .........................................................2A-73
High lift boom spec. ...................................... 3A-144
Log grapple spec. ......................................... 3A-135 C
Lumber fork spec. ......................................... 3A-134 Calculation of production......................................14A-2
Lumber grapple spec. ................................... 3A-132 Carcass .................................................................. 12-6
Attachment and options Carry position .....................................................3A-104
Motor grader ................................................... 5A-16 Chip bucket ........................................................ 3A-110
Off high-way dump truck................................. 4A-35 Coal dozer ..............................................................1B-2
Automatic three-mode suspension ...................... 4A-36 Component dimensions and weights
Auto retard speed control .................................... 4A-36 Excavators, backhoes .....................................2A-45
Hydraulic loading shovels..................................2E-8
Concrete debris ......................................................8A-5
Concrete pulverizer ............................................... 2G-9
Cone index numbers (qc) ................................... 14B-11
Conventional tire .................................................... 12-5
Conversion tables................................................... 16-2
Correct usage....................................................... 12-11
Cross loading .......................................................14A-7
INDEX-1
Index.fm Page 2 Friday, March 26, 2004 1:22 PM
INDEX
D Pipelayers..........................................................1E-2
Railway maintenance machines ....................... 2H-2
Depreciation ........................................................... 15-2
Reach loaders ...................................................3B-2
Differential lock .................................................... 4A-37
Reach tower cranes...........................................9B-2
Digging force
Rippers ............................................................. 1C-2
Excavators, backhoes..................................... 2A-37
Rough terrain cranes .........................................9A-2
Hydraulic loading shovels ................................. 2E-7
Rubber crawler ..................................................2A-7
Minimal swing radius excavators (uu)............... 2B-6
Slag dump trucks.............................................. 4D-2
Wheel-type excavators ......................................2F-8
Skid steer loaders................................................ 7-2
Dimensions
Tire roller .......................................................... 5C-2
Backhoe loader.................................................... 6-4
Towing tractors ..................................................3E-2
Excavators, backhoes..................................... 2A-27
Trash compactors & trash loaders.................... 3D-2
Hydraulic loading shovels ................................. 2E-6
US-series...........................................................2A-8
Minimal swing radius excavators (uu)............... 2B-5
Vibratory rollers .................................................5B-2
Motor graders ................................................... 5A-6
Wheel dozer ..................................................... 3C-2
Off-highway dump trucks .................................. 4A-8
Wheel loaders....................................................3A-2
Reach loader .................................................... 3B-4
Wheel-type excavators ...................................... 2F-2
Reach tower cranes.......................................... 9B-4
Fork equipment features ....................................3A-129
Rough terrain cranes ........................................ 9A-9
Front blade ...........................................................5A-18
Trash compactor ............................................... 3D-4
Front pull hook......................................................5A-18
Vibratory rollers................................................. 5B-5
Fuel consumption ................................................. 15-11
Wheel dozer...................................................... 3C-4
Fueling deration rate .............................................. 11-6
Wheel loaders................................................. 3A-17
Wheel-type excavators ......................................2F-6
Drawbar pull vs. travel speed .............................. 1A-13 G
Dual-axis shear...................................................... 8A-4 General purpose bucket ..................................... 3A-110
Dual tiltdozer.......................................................... 1B-2 Grade factor .........................................................14A-5
Dumping clearance and reach........................... 3A-104 Bulldozers........................................................1B-16
Dumping fork ..................................................... 3A-129 Grade resistance ..................................................14B-8
Grind mill ................................................................8B-2
E Ground pressure
Earth volume conversion factor ........................... 14A-2 Excavators, backhoes .....................................2A-64
Elements limiting the inherent machine capability14B-4 Crawler-type tractors .......................................1A-16
Engines used in KOMATSU machine ..................... 11-4
Estimating rippability.............................................1C-11 H
Estimated production Hauling performance of construction machines ...14B-4
Bulldozers ....................................................... 1B-16 Hauling resistance................................................14B-8
Excavators, backhoes................................... 2A-100 Heaped capacity...................................................2A-71
Hydraulic loading shovels ............................... 2E-20 Heavy-duty bucket.............................................. 3A-110
Off-highway dump trucks ................................ 4A-53 Hydraulic cycle times..........................................3A-103
Rippers ........................................................... 1C-14
Wheel loaders............................................... 3A-152 I
Estimating the owning & operating costs................ 15-2 Impact crusher........................................................8A-4
Exhaust retarder .................................................. 4A-36 Inherent machine capability..................................14B-4
Extension blade ................................................... 5A-18 Inner liner ............................................................... 12-5
Extension fork.................................................... 3A-130 Insurance................................................................ 15-3
Interest ................................................................... 15-3
F
5-stage dust indicator .............................................13-4 J
Features Jaw crusher ............................................................8A-4
Articulated dump truck ...................................... 4B-2 Job efficiency
AVANCE series (Excavators)............................ 2A-5 Bulldozers........................................................1B-16
AVANCE series (Wheel loaders) ...................... 3A-2 Excavators, backhoes ...................................2A-100
Bulldozers ......................................................... 1B-2 Off-highway dump trucks.................................4A-53
Backhoe loaders .................................................. 6-2 Wheel loaders................................................3A-152
Crawler-type tractors ........................................ 1A-2 Jumbo crusher......................................................2G-11
Dash-7 series.................................................... 2A-2
Engines.............................................................. 11-2 K
Generator sets ................................................... 10-2
Hydraulic loading shovels ................................. 2E-2 KIRD..................................................................... 15-20
HD series .......................................................... 2A-8
Minimal swing radius excavators (uu)............... 2B-3 L
Mobile crusher & recyclers ............................... 8A-3 Lifting capacity
Mobile soil recycler ........................................... 8C-2 Excavators, backhoes ...................................... 2C-2
Mobile wood tub grinders.................................. 8B-2 Minimal swing radius excavators (uu) ...............2B-7
Motor graders ................................................... 5A-2 Wheel-type excavators .................................... 2F-12
Off-highway dump trucks .................................. 4A-2 Light material bucket .......................................... 3A-110
Komatsu mining shovels................................... 2A-9 Liner-less body .....................................................4A-42
Load and carry .....................................................14A-7
INDEX-2
Index.fm Page 3 Friday, March 26, 2004 1:22 PM
INDEX
INDEX-3
Index.fm Page 4 Friday, March 26, 2004 1:22 PM
INDEX
T Working range
Excavators backhoes ......................................2A-37
Tailgate selection ................................................. 4A-52
Hydraulic loading shovels..................................2E-7
Teeth selection..................................................... 2A-84
Minimal swing radius excavators (uu) ...............2B-6
Three-way emergency brake............................... 4A-37
Wheel-type excavators ...................................... 2F-8
Tip radius............................................................. 2A-73
Tip-type teeth...................................................... 3A-111
Tire availability
Motor graders ................................................. 5A-15
Off-highway dump trucks ................................ 4A-39
Wheel loaders............................................... 3A-145
Tire characteristics ............................................... 12-10
Tire classifications .................................................. 12-2
Tire life .................................................................. 15-18
Tire manufacturer’s designation ............................. 12-3
Tire selection
Off-highway dump trucks ................................ 4A-39
Tire size designation............................................... 12-5
TMPH ...................................................................12-10
TMPH rating ........................................................ 4A-39
TORQFLOW drive type tractor ............................ 14B-5
Total rated loads
Reach tower crane............................................ 9B-5
Rough terrain crane ........................................ 9A-10
Traffic-ability .......................................................14B-11
Travel performance curve
Off-highway dump trucks
HD255-5......................................................4A-11
HD325-6..................................................... 4A-13
HD325-6 4WD............................................ 4A-15
HD405-6..................................................... 4A-17
HD465-7..................................................... 4A-19
HD605-7..................................................... 4A-21
HD785-5..................................................... 4A-23
HD985-5..................................................... 4A-27
HD1200-1................................................... 4A-29
HD1500-5................................................... 4A-30
630E........................................................... 4A-31
730E........................................................... 4A-32
830E........................................................... 4A-33
930E-2 ....................................................... 4A-34
Travel time
Off-highway dump trucks ................................ 4A-53
Tread ...................................................................... 12-5
Tread pattern .......................................................... 12-9
Trimming blade .......................................................1F-3
Trimming operation in vessel..................................1F-2
Triple-grouser shoe ............................................. 1A-19
Tubes and flaps ...................................................... 12-6
U
U-tiltdozer .............................................................. 1B-2
Use of brake performance curve ......................... 4A-10
Use of travel performance curve
Off-highway dump trucks ................................ 4A-10
Upper attachment
Crawler type tractors....................................... 1A-23
Motor graders ................................................. 5A-14
V
V-shape loading................................................... 14A-7
W
Water separator .......................................... 4A-38, 13-3
Wet type disc brake ............................................. 5A-19
Working radius
Reach tower cranes........................................ 9B-22
Rough terrain cranes ...................................... 9A-21
INDEX-4
AH_25.book Page 5 Tuesday, March 23, 2004 9:41 AM
MEMO
AH_25.book Page 6 Tuesday, March 23, 2004 9:41 AM
MEMO