Professional Documents
Culture Documents
Granite Concrete (GC) & Other Concrete (Oc) Notes Timber Pole (TP) Service Support Notes
Granite Concrete (GC) & Other Concrete (Oc) Notes Timber Pole (TP) Service Support Notes
Maximum 3'
to conduit
to the electrical service pole and underground
2. Provide prestressed concrete poles suitable for direct embedment into
within 12 in. of service pole are not paid
the ground without special foundations.
60" TYP
for directly but are subsidiary to the electrial Detail A
strap
service.
3. Verify poles are marked as required on DMS 11080. Location of marking
should be approximately 4' above final grade. Use the two-point pickup
3. Install pole-top mounted photocell (T) on
locations when handling pole in horizontal position, and one-point Extend •" PVC
The use of this standard is governed by the "Texas Engineering Practice Act".
Min.
Min.
pole in a neat and workmanlike manner.
18"
18"
42" min.
6. Install a one point rack or eye bolt bracket 6 inches to 12 inches below
5. Mount meter and service equipment on stainless
the weatherhead as an overhead service drop anchoring point for the
steel or galvanized channel (Unistrut, Kindorf, PVC, or other
electric utility.
or equal). Provide channel sized 1 in. to 3 ƒ in. RMC
conduit type
maximum depth, and 1• in. to 1† in. maximum as shown on
7. Furnish and install galvanized or stainless steel channel strut 1 • in. 6" to 10"
width. File smooth the cut ends of galvanized layout
or 1 † in. wide by 1 in. up to 3 ƒ in. deep (Unistrut, Kindorf, B-line
channel and paint with zinc rich paint before
or equal). Attach channel strut with stainless steel concrete anchors (max.
installing on pole. Secure each channel section RMC ell
1" depth), square U-bolts or back to back channel strut with long bolts, Bushing
kind is made by TxDOT for any purpose whatsoever.
White Insulation or
color code 6" length
2" to 6" 2" to 6" (4" typ.)
neutral conductor's
4" typ. (As required or allowed
1 Class 5 pole, height as required insulation with 6" to 12"
by utility company)
white tape where
conductor exits
2 Service drop from utility company
Point of the weatherhead.
(attached below weatherhead)
attachment
2 Red insulation or
25' measured from grade.
DISCLAIMER:
to be below
color code 6" length
3 Service conduit (RMC)and service weatherhead Circumstances may require the
of Line 1 or Line 2
electrical service support
entrance conductors - One Red, conductor's insulation
to be taller than the 25'
One Black, One White (See Electrical with red tape where
10 3 shown, check with utility
Service Data) conductor exits
before installing
the weatherhead.
RMC
Conductor slack
4 Safety switch (when required)
length, 12" min., Service
18" max. Enclosure
5 Meter (when required)
11
6 Service enclosure Safety Switch Side View Top View
Pole marking
(when required)
approx. 4'
7 6 AWG bare grounding electrode
Pole brand above ground
conductor in • in. PVC to must be line. DETAIL A
ground rod - extend • in. PVC 5' or less
6 in. underground. above grade See Note 7. Before installing channel
that has been cut, file sharp edges and
60" TYP
See Detail A paint with zinc-rich paint. Ensure
8 † in. x 8 ft. Copper clad
4 there is no paint splatter on the pole.
ground rod - drive ground rod 6
to a depth of 2 in. to 4 in. XXXXXXXXXXX
Extend 1/2"
XXXXXXXXXXX 5
below grade. 5-30 PVC 6"
XXXXXXXXXXX
Min.
Division
18"
detail on ED(5). Standard
burial depth
Min.
10% of pole
length plus
18"
is greater
2' or 42"
whichever
6"
Embedment
12 When required by utility, cut C TxDOT October 2014 CONT SECT JOB HIGHWAY
71K