Professional Documents
Culture Documents
EIM Finals
EIM Finals
EIM Finals
GENERAL INSTRUCTIONS:
Any form of cheating means a failing grade in this examination.
Read and follow the directions carefully.
Do not write or put markings in the test questionnaire.
Write your answers neatly in your answer sheet. NO ERASURES.
4.
1.
2.
5.
3.
6.
7.
EIM II - page 2
8. This is usually bare solid or stranded conductor used for overhead transmission lines and ground
wires.
A. Copper or aluminum conductor
B. Non-metallic sheathed cable (type NM)
C. Thermoplastic covered fixture wire (type TF)
D. Copper or aluminum PE insulated line wire
9. This is a flame retardant, moisture resistant wire used for building wiring installation in dry or wet
locations.
A. Thermoplastic Portable cords (types SJT & ST)
B. Thermoplastic wire (type TW)
C. Control cable (braided type)
D. Flat Cord (type SPT)
10. A wire commonly used for wiring motorized engines and appliances with high temperature, and
for switch board wiring.
A. Temperature wire (type HI)
B. Control cable (braided type)
C. Asbestos covered nickel cord (Rockbestos)
D. Steel tape armored power cable with ground wire (Copper)
11. This is a multi-conductor cable generally used for interior wiring installations in dry and wet
locations.
A. Power cable
B. Nonmetallic sheathed cable (type NMC)
C. Royal cable
D. Submersible pump cable
12. What is the equivalent diameter size of number 10 AWG wire in millimeter (mm)?
A. 2.05mm C. 3.26mm
B. 2.59mm D. 3.11mm
13. What is the equivalent diameter size of number 8 AWG wire in millimeter (mm)?
A. 2.05mm C. 3.26mm
B. 2.59mm D. 3.11mm
14. It is a type of flexible armored cable that has rubber insulation and a lead sheath between the
conductor and the armor.
A. type AC C. type ACV
B. type ACT D. type ACL
16. What do you call a plastic or metal material that is used for mounting of convenient outlets and
switches on walls?
A. Junction Box B. Frames
EIM II - page 3
18. What is the safety device which automatically cuts off current that exceeds the circuit rating?
A. Circuit C. Conduit
B. Circuit Breaker D. Galvanic Reaction
19. It is a conduit fitting used to make a 90 degree change in direction of the conduit run to a quarter
bend.
A. Coupling C. Nipples
B. Offset D. Elbow
20. It is a process of removing sharp edges or burrs left after cutting the pipe.
A. shaping C. finishing
B. reaming D. smoothing
21. How many degrees in the direction of conduit run does a quarter angle bend provides?
A. 45 degrees C. 135 degrees
B. 90 degrees D. 180 degrees
22. It is the maximum recommended number of 8.0mm (no.8 AWG) wires a 20mm (3/4 inch) diameter
conduit can accommodate.
A. 6 C. 10
B. 8 D. 12
23. What size of conduit can accommodate at least ten (10) 8.0mm (No.8AWG) wires?
A. 3/8 C. 3/4
B. 1/2 D. 1 ¼
25. It is a short length conduit or tubing which is used to extend a conduit system and also used
between conduit and tubing such as boxes or enclosures between two boxes.
A. connector C. nipple
B. coupling D. condulets
28. It is a tool used to bend rigid metallic conduits more than 1” in diameter.
A. pneumatic motor C. hydraulic knockout
B. hydraulic pump D. hydraulic pipe bender
29. It is a picture symbol intended to alert you to, and or instruct you on how to avoid a potentially
hazardous condition.
A. motor C. sign
B. warning icon D. symbol
31. The purpose of turning the drill on before attempting to drill a hole is to ___________.
A. check if the power cord is good
B. make sure the chuck key has been removed
C. see if the drill bit is running true
D. see if the drill operates
34. What type of drill speed is needed for wood drilling operations?
A. high C. low
B. medium D. low-medium
35. What type of drill speed is needed for most metal drilling operations?
A. low C. medium-high
B. medium-low D. high
36. What kind of pressure should be applied to a drill during a drilling operation?
A. light, even C. moderate, even
B. medium, even D. heavy, even
37. What will likely happen if a large capacity portable drill bit jams during the drilling operation?
A. The hole will become badly distorted.
B. The drill will likely stall out and overheat.
C. The drill will rotate in the opposite direction to the bit causing injury to the user’s wrists.
D. The bit will break.
EIM II - page 5
38. The purpose of moving the drill and the bit up and down often while drilling deep holes is to ____.
A. reduce overheating in the drill bit
B. help keep the hole centered
C. give the drill operator better drilling leverage
D. ream the hole slightly larger.
39. What personal protective equipment should be worn when operating the portable disc grinder?
A. safety glasses, hearing protection, gloves, and respirator
B. safety glasses, hearing protection, and gloves
C. safety glasses, and hearing protection
D. safety glasses
40. When operating the portable disc grinder, the grinding disk should be positioned so that the sparks
and grit are thrown ________.
A. away from the operator
B. away from the operator and others in the work area
C. up to avoid hitting others
D. down to avoid hitting others
41. Grinding with a portable disc grinder should not be done in an area which ________.
A. is enclosed
B. has windows
C. is clean
D. contains flammables or combustible gases
42. The grinding disc should be replaced when worn out and reduced to ________ of its original
diameter.
A. ¼ C. 5/8
B. ½ D. ¾
43. Hands and arms should be protected by wearing ________ when using the portable disc grinder.
A. long sleeved leather gloves C. long sleeved leather jacket
B. long sleeved shirt D. gloves
44. What may possibly happen when the wire brush attachment is used on the portable disc grinder?
A. The grinder may be thrown out from the user’s grip.
B. The grinder stays steady on the material being brushed.
C. The grinder moves back and forth.
D. The grinder performs well.
45. When the portable disc grinder is laid down, it should be positioned ________.
A. with the disc down
B. on its left side
C. on its right side
D. on the tool rest with the grinding disc facing up
EIM II - page 6
46. What is the minimum size of the electrical extension cord used with the portable disc grinders?
A. # 2.0mm2 C. # 5.5mm2
B. # 3.5mm2 D. # 8.0mm2
47. Which of the following injuries will be caused by compressed air if used to clean clothes, hands or
body soiled with a flammable cleaning solvent?
A. apron C. burn
B. blood poisoning D. pimples
48. Which of the following solvents should not be used as a cleaning solution for it poses hazards to
health?
A. water
B. carbon tetrachloride
C. kerosene
D. gasoline
49. As a safety precaution, which of the following safety devices should be worn in electrical wiring?
A. face shield C. apron
B. rubber gloves D. face mask
50. Which of the following should we use to keep a flammable cleaning solvent?
A. closed tin container
B. aluminum basin
C. plastic pail
D. fire ball
ABARAGUER/October2017