Professional Documents
Culture Documents
Ia6 Ia24: Instruction Manual
Ia6 Ia24: Instruction Manual
Ia6 Ia24: Instruction Manual
iA24
iA6
IC-A24 IC-A6
Thank you for purchasing this Icom product. The IC-A24/A6
VHF AIR BAND TRANSCEIVER is designed and built with SUPPLIED ACCESSORIES
Icom’s state of the art technology and craftsmanship. With
proper care this product should provide you with years of
trouble-free operation.
Antenna Handstrap Belt clip
IMPORTANT
READ ALL INSTRUCTIONS carefully and completely be-
fore using the transceiver.
SAVE THIS INSTRUCTION MANUAL— This instruction
manual contains important operating instructions for the
IC-A24/A6. Wall charger* Battery pack* Carrying Headset
or battery case case* adapter*
EXPLICIT DEFINITIONS * Not supplied, or the shape may be different, depending on the
version.
The explicit definitions below apply to this instruction man-
ual.
Icom is not responsible for the destruction, damage to, or
WORD DEFINITION performance of any Icom or non-Icom equipment, if the
Personal death, serious injury or an explo- malfunction is because of:
RDANGER!
sion may occur. • Force majeure, including, but not limited to, fires,
Personal injury, fire hazard or electric shock earthquakes, storms, floods, lightning, other natural
RWARNING!
may occur. disasters, disturbances, riots, war, or radioactive
CAUTION Equipment damage may occur. contamination.
If disregarded, inconvenience only. No risk • The use of Icom transceivers with any equipment that is
NOTE
of personal injury, fire or electric shock. not manufactured or approved by Icom.
i
PRECAUTION
R DANGER! NEVER short the terminals of the battery pack. DO NOT operate the transceiver near unshielded electrical
Also, current may flow into nearby metal objects, such as a blasting caps or in an explosive atmosphere.
necklace, etc. Therefore, be careful when carrying with, or
DO NOT use or place the transceiver in direct sunlight or
placing near metal objects, carrying in handbags, etc.
in areas with temperatures below –10°C (+14°F) or above
R DANGER! Use and charge only specified Icom battery +60°C (+140°F).
packs with Icom radios or Icom chargers. Only Icom battery
packs are tested and approved for use with Icom radios or Even when the transceiver power is OFF, a slight current still
charged with Icom chargers. Using third-party or counterfeit flows in the circuits. Remove the battery pack or case from
battery packs or chargers may cause smoke, fire, or cause the transceiver when not using it for a long time. Otherwise,
the battery to burst. the battery pack or installed Alkaline cell batteries will be-
come exhausted.
R WARNING! NEVER hold the transceiver so that the anten-
na is very close to, or touching exposed parts of the body, es- FCC caution: Changes or modifications to this trans-
pecially the face or eyes, while transmitting. The transceiver ceiver, not expressly approved by Icom Inc., could void
will perform best if the microphone is 5 to 10 cm (2 to 4 inches) your authority to operate this transceiver under FCC regu-
away from the lips and the transceiver is vertical. lations. (U.S.A. only)
R WARNING! NEVER operate the transceiver with a head-
set or other audio accessories at high volume levels. Hear-
CAUTION: Use of 8.33 kHz Channel Spacing of this radio
ing experts advise against continuous high volume operation.
is strictly prohibited and shall not be used in Canada.
If you experience a ringing in your ears, reduce the volume
level or discontinue use.
CAUTION: NEVER connect the transceiver to an AC outlet or MISE EN GARDE: Utilisation de 8.33 kHz Espacement
to a power source of more than 11.5 V DC. Such a connection des canaux de cette radio est strictement interdite et ne
will damage the transceiver. doit pas être utilisé au Canada.
DO NOT allow children to play with any radio equipment con-
Icom, Icom Inc. and Icom logo are registered trademarks of Icom Incorporated
taining a transmitter.
(Japan) in Japan, the United States, the United Kingdom, Germany, France,
Spain, Russia, Australia, New Zealand, and/or other countries.
ii
TABLE OF CONTENTS
IMPORTANT....................................................................................... i 5 SCAN OPERATION.............................................................16–17
EXPLICIT DEFINITIONS.................................................................... i ■■Scan types.............................................................................16
SUPPLIED ACCESSORIES............................................................... i ■■COM band scan.....................................................................16
PRECAUTION................................................................................... ii ■■Memory scan.........................................................................16
■■Weather channel scan (U.S.A. version only)..........................17
1 ACCESSORY ATTACHMENT.....................................................1
■■“TAG” channel setting.............................................................17
2 PANEL DESCRIPTION...........................................................2–7
■■Panel description.....................................................................2 6 VOR NAVIGATION (IC-A24 ONLY).....................................18–24
■■VOR indicators.......................................................................18
■■Function display.......................................................................6
■■VOR functions........................................................................19
3 BASIC OPERATION..............................................................8–11 ■■Flying to a VOR station..........................................................20
■■Setting a frequency..................................................................8 ■■Entering a desired course......................................................22
■■Selecting a weather channel (U.S.A. version only)..................8 ■■Crosschecking position..........................................................22
■■Receiving.................................................................................9 ■■Duplex operation (U.S.A. version only)..................................24
■■ANL function............................................................................9
■■Channel spacing setting...........................................................9 7 CLONING..................................................................................25
■■Setting a squelch level.............................................................9 8 BATTERY PACKS...............................................................26–29
■■Transmitting..............................................................................9 ■■Battery cautions.....................................................................26
■■Low battery indicator..............................................................10 ■■Battery charging.....................................................................26
■■Recall function.......................................................................10 ■■Optional battery case.............................................................27
■■Setting weather alert function................................................11 ■■Optional battery chargers......................................................28
■■Accessing the 121.5 MHz emergency frequency...................11 9 SPECIFICATIONS...............................................................30–31
■■Lock function..........................................................................11 10 OPTIONS...................................................................................32
■■Side tone function..................................................................11
11 OPTIONAL HEADSET CONNECTION.....................................33
■■Setting beep tone...................................................................11
12 SAFETY TRAINING INFORMATION..................................34–35
4 MEMORY OPERATION.......................................................12–15
■■Memory channel selection.....................................................12 13 FCC INFORMATION.................................................................36
■■Transferring memory contents...............................................12 14 TROUBLESHOOTING..............................................................37
■■Programming a memory channel...........................................13
INDEX........................................................................................38–39
■■Memory names......................................................................14
■■Clearing the memory contents...............................................14
iii
ACCESSORY ATTACHMENT 1
ïïAntenna ïïBelt clip 1
CAUTION: DO NOT transmit without an antenna. Other- Conveniently attaches to your belt.
2
wise the transceiver may be damaged. Attach the belt clip with the supplied screws as below.
NOTE: Use the supplied screws only. 3
Insert the supplied antenna into the antenna connector and
screw down the antenna as shown below. Supplied screws 4
5
6
7
8
9
ïïBattery pack replacement 10
Before replacing the battery pack, push [PWR] for 2 seconds 11
to turn the power OFF.
12
Slide the battery release button forward, then pull the battery 13
pack upward with the transceiver facing away from you.
14
e r t
y
u
i
w
o !7
IC-A6
q WX-ALERT
!0
!1
!7
!2
!3
!6
Microphone
!5
Speaker
!4
!7
2
PANEL DESCRIPTION 2
!1 CLEAR KEY [CLR•DEL] (pp. 8–17) !6 ENTER KEY [ENT•WX] (pp. 8, 14)
➥ Push to return to the frequency mode, when ➥ Push to store the numeral input. Enters con-
memory channel, WX channel, 121.5 MHz, secutive zero digits. (p. 8)
squelch level setting or beep tone setting is se- ➥ Push , then push [ENT• WX ] to enter the
lected. weather channel selection mode (U.S.A. ver-
➥ Push , then hold down [CLR•DEL] to delete sion only). (p. 8)
a recall frequency data. ➥ Push to program the memory name. (p. 14)
➥ Push to clear the entered comment of memory NOTE: Some functions may not be available depending on
name while programming. versions. Ask your authorized dealer for details.
➥ Push to stop the scan function to return to the
frequency mode while the scan function is op- • DC POWER CONNECTION
erating. R WARNING!
• N EVER modify the CP-20. A modification
!2 ANL KEY [ANL•SCAN] (pp. 9, 16, 17) could cause a fire or electrocution.
➥ Push to turn the ANL function ON or OFF. • NEVER cut or fray the CP-20’s power cable
➥ Push , then push [ANL•SCAN] to start the IC-A24/A6 when disconnecting/connecting the CP-20
scan function. from/to the cigarette lighter socket.
!4 DC POWER JACK
Connect the AC adapter or optional cable, to charge the
battery pack or to operate by external power. (see right il- To the cigarette
lustration) lighter socket
Wall charger
To [DC 11V]
!5 MEMORY MODE KEY [MR•MW] (pp. 12–15) To AC outlet
➥ Push to select the memory channel mode.
The shape may
➥ Push , then push [MR•MW] to program the differ depending
contents into the memory channels. on the version.
4
PANEL DESCRIPTION 2
5
2 PANEL DESCRIPTION
■■Function display
q FUNCTION INDICATOR (p. 3)
Appears when is pushed.
w TX INDICATOR (p. 9)
Appears while transmitting.
q w e r t y
e RX INDICATOR (p. 9)
Appears when receiving a signal, or when the squelch
opens.
6
PANEL DESCRIPTION 2
1
u FREQUENCY DISPLAY (pp. 8, 14) !3 COURSE DEVIATION NEEDLES (IC-A24 only) 2
➥ Shows the operating frequency. (pp. 18–22)
➥ S hows the channel name when the memory name Indicates every 2 degree deviation between the desired
3
function is selected. course and your actual flying course every 2 degrees. 4
[NOTE]
When you set the IC-A24/A6’s channel spacing to !4 COURSE INDICATORS (IC-A24 only) (p. 19)
5
8.33 kHz, the displayed frequency is different from the ac- ➥ Indicates where your aircraft is located on a VOR radial 6
tual operating frequency. in the DVOR mode.
See “VFO CHANNEL ID LIST” for details. (p. 31) ➥ Indicates where your desired course is located on a 7
VOR radial in the CDI mode. 8
i TAG CHANNEL INDICATOR (p. 17)
“ ” appears when the selected memory channel is set !5 TO-FROM INDICATOR (IC-A24 only) (p. 19) 9
as a TAG channel. Indicates whether the VOR navigation information is 10
based on a course leading to the VOR station or leading
o MEMORY CHANNEL INDICATOR (pp. 12–15) away from the VOR station. 11
Shows the selected memory channel number.
12
!0 MEMORY BANK NUMBER INDICATOR (p. 12) 13
Shows the selected memory bank number.
14
!1 OVERFLOW INDICATOR (IC-A24 only) (pp. 18–22)
Appears when the deviation between the desired course
and flying course is over 10 degrees.
7
3 BASIC OPERATION
■■Setting a frequency
ïïUsing keypad ïïUsing the tuning dial
q Push [PWR] for 2 seconds to turn power ON, then push q Push [PWR] for 2 seconds to turn power ON, then push
[CLR•DEL] to select the frequency mode when memory [CLR•DEL] to select the frequency mode when memory
CH number or WX CH number appears on the function CH number or WX CH number appears on the function
display. display.
w Push 6 appropriate digit keys to input the frequency. w Rotate [DIAL] to set the desired frequency.
• When operating on only 25 kHz channel spacing, push • To select the 1 MHz tuning step, push , then rotate
5 appropriate digit keys to input the frequency. [DIAL]. Push again to return to the normal tuning.
• Push [ENT•WX] to enter remaining zero digits.
• When a wrong digit is input, push [CLR•DEL] to clear,
then repeat step w again.
■■Selecting a weather channel
[EXAMPLE]
When operating on either only 8.33 kHz channel spacing
(U.S.A. version only)
or 8.33 kHz/25 kHz channel spacing.
• 111.225 MHz: Push The U.S.A. version has VHF marine WX (weather) channel
• 117.250 MHz: Push receiving capability for flight planning.
• 118.0083 MHz: Push q P ush , then push [ENT• WX ] to select WX channel
• 119.0667 MHz: Push mode.
• “WX--” and the previously selected
• 120.0917 MHz: Push
channel number appears.
When operating on only 25 kHz channel spacing. w Rotate [DIAL] to select the de-
• 111.225 MHz: Push sired WX channel.
• 117.250 MHz: Push e Push [CLR•DEL] to exit the WX
• 120.000 MHz: Push channel mode and return to fre-
• 125.300 MHz: Push quency mode.
8
BASIC OPERATION 3
■■Recall function
The recall function stores the last 10 frequencies used.
The function stores frequencies when the frequency is pro- ïïReplaces the stored recall channel
grammed and transmitted on (except memory, weather and q Push or to select the recall channel to be re-
emergency channels). placed.
w Push , then push or to replace it.
ïïRecalling the stored frequencies • Replaces the selected channel into the previous channel when
is pushed and then is pushed.
➥ Push to recall the 1st stored frequency.
• Replaces the selected channel into the next channel when
➥ Push to recall the 10th stored frequency. is pushed and then is pushed.
• (e.g.) To replace “r0” which is stored as 121.375 MHz into “r1”,
push , then push .
: Push
: Push NOTE: When the number of stored frequencies reaches
10, channels are automatically deleted as needed, in the
order they were entered, beginning the oldest.
10
BASIC OPERATION 3
13
4 MEMORY OPERATION
■■Memory names
ïïProgramming memory names Key Character Key Character Key Character
The memory channel can display a 6-character name in- 1 1, Q, Z 2 2, A, B, C 3 3, D, E, F
stead of the programmed frequency.
4 4, G, H, I 5 5, J, K, L 6 6, M, N, O
q In the frequency mode, rotate [DIAL] to select the desired 7 7, P, R, S 8 8, T, U, V 9 9, W, X, Y
frequency in the frequency mode. ENT Program 0 0, space, -
w Push , then push [MR•MW] to program the contents
into the selected memory channel.
e Rotate [DIAL] to select the desired memory channel to be NOTE: When programming the memory name to the pro-
programmed. grammed memory channel do the following.
• Push , then push [0•BANK], and rotate [DIAL] to select the q Follow the same steps as in “Transferring memory con-
BANK number, if desired. Push [CLR•DEL] to exit the BANK se- tents” (see p. 12).
lection mode. w Follow steps w–y in “Programming memory names”
r Push [MR•MW] to enter the memory name programming (see left column).
mode.
• “-- -- -- -- -- -- ” appears on the display.
t Push the appropriate digit key several times to select the
desired character, as listed to the right. ■■ Clearing the memory contents
• To erase a character, overwrite with a space (displayed as _).
• To move the cursor forwards or backwards, use [DIAL].
y Push [ENT•WX] to program the name. Unwanted memory channels can be cleared.
• The memory name stops flashing.
• When no name is programmed, the display shows the operat- q Select the memory channel to be cleared.
ing frequency. w Push , then hold down [CLR•DEL] for 1 second.
• To clear the entered memory names, push [CLR•DEL] before • “-- -- -- -- -- --” appears momentarily, then the next selectable
pushing [ENT•WX]. channel appears.
14
MEMORY OPERATION 4
• EXAMPLE: Programming 125.000 MHz into memory BANK 1/ memory channel 17 with “AIR-23” as a comment. 1
Push 2
Push Push
(or rotate [DIAL]) 3
4
5
6
Push Push 7
Push Push
(or rotate [DIAL]) 8
9
10
11
Push 12
Push Push Push
13
14
15
5 SCAN OPERATION
■■Memory scan
MEMORY SCAN q Push [MR•MW] to select the memory mode.
Repeatedly scans all • Push , then push [0•BANK], and rotate [DIAL] to select the
non-TAG channel selected memory bank’s BANK number, if desired. Push [CLR•DEL] to exit the BANK se-
Mch 2 Mch 4 Mch 6 “TAG” memor y chan- lection mode.
nels. Used for checking w P ush [SQL• WX-ALERT ], then rotate [DIAL] to set the
Mch 1 Mch 7
often-used channels squelch level to the point where noise is just muted.
non-TAG
Mch 19 Mch 10 Mch 8 channel and bypassing usually e Push , then push [ANL•SCAN] to start the scan.
busy channels such as • When a signal is received, the scan pauses until it disappears.
control-tower frequen- • To change the scanning direction, rotate [DIAL].
cies. r To stop the scan, push [CLR•DEL].
16
SCAN OPERATION 5
■■VOR indicators
NAV BAND (108.000 117.975 MHz)
COM BAND
(118.000 136.9917 MHz) DVOR MODE
To-from flag
Course indicator indicator
Push [F], then push [1 DVOR]. Push [F], then push [4 CDI].
CDI MODE
18
VOR NAVIGATION (IC-A24 ONLY) 6
19
6 VOR NAVIGATION (IC-A24 ONLY)
■■Flying to a VOR station r The course deviation needle appears when your aircraft
is off course from the VOR station.
• ‘Ω’ or ‘≈’ appears to indicate your aircraft is off course to the
The IC-A24 shows the deviation from a VOR station. right or left, respectively. Correct your course until ‘Ω’ or ‘≈’ dis-
appears. Each arrow represents a two-degree deviation.
q Select a VOR station on your aeronautical chart and push t Push , then push [1•DVOR] to exit the CDI mode.
the keypad or rotate [DIAL] to set the frequency of the
station.
• The course indicator indicates where you are located on a ra- VOR INDICATOR NOTE
dial from the VOR station. ‘loc’ appears on the function display as shown below when
• The course indicator shows ‘- -’ when either aircraft is too far a localizer signal is received.
away from the VOR station or the frequency is not set correctly
at the VOR station. However, the function display does not indicate additional
w Select the ‘TO’ flag when flying to the VOR station, or se- information about the localizer signal.
lect the ‘FROM’ flag when flying away from the VOR sta-
tion.
• Push , then push [2•TO] to select ‘TO’.
• Push , then push [3•FROM] to select ‘FROM’.
e Push , then push [4•CDI] to select the CDI (Course
Deviation Indicator) mode.
• The course indicator shows ‘OF’ when the desired VOR signal
cannot be received.
310 320
330 340
350
0
N 1
THE AIRCRAFT IS ON COURSE
123.65
300 Magnetic
VORTAC
SEATTLE
290
280
10
20
north 2
116.8 Ch 115 SEA
260
270 30
40
3
250 50 4
240 60
230
VOR 70 5
rse
220 station 80
ed cou 210 90 6
D esir g 40 200 100
w nc 220 station 80
Flo 210 90
be 200 100
uld
NOTE: The course deviation indica- sho 190 110
i r c raft 40 180
170 130
120
A
ding
160 150 140
tor appears when the aircraft is off
hea
course. In this example, the aircraft
is 6 degrees off course to the left.
The pilot must turn more than 6 de-
grees right to get back on course.
21
6 VOR NAVIGATION (IC-A24 ONLY)
q w e r
q Overflow indicator (left)
w Course deviation needles (left)
e Course deviation needles (right)
r Overflow indicator (right)
22
VOR NAVIGATION (IC-A24 ONLY) 6
23
6 VOR NAVIGATION (IC-A24 ONLY)
EXAMPLE: Programming 123.65 MHz as the transmit frequency in the duplex function.
24
CLONING 7
Cloning allows you to quickly and easily transfer the r When cloning is finished, turn power OFF, then ON again 1
programmed data from one transceiver to another to exit the cloning mode.
transceiver, or, data from a PC to a transceiver, using the 2
optional CS-A24 (#02) cloning software. NOTE: DO NOT transfer the data from a IC-A24 to a IC- 3
A6, when the data contains the NAV band data. In such
ïïTransceiver to transceiver cloning case, a cloning error may occur. 4
q C onnect the OPC-474 CLONING CABLE with adapter 5
plugs to the [SP/MIC] jack of the master and sub trans- ïïCloning using PC
ceivers.
Data can be cloned to and from a PC (Microsoft® Windows®
6
• The master transceiver is used to send data to the sub trans-
ceiver. XP) using the optional CS-A24 (#02) cloning software and 7
the optional OPC-478 (RS-232C type), OPC-478U or OPC-
w While holding down [MR•MW], push
478UC (USB type) cloning cable . Consult the CS-A24
8
[PWR] to enter the cloning mode (to
operate the master transceiver (#02) cloning software HELP file for details. 9
only). 10
• “CLONE” appears and the transceivers ïïCloning error
enter the clone standby condition. NOTE: DO NOT push [ENT•WX] on the sub transceiver 11
e Push [MR•MW] on the master trans-
ceiver.
during cloning. This will cause a cloning error. 12
• “CL-OUT” appears in the master trans-
When the display at right appears, a 13
ceiver’s display.
• “ COURSE DEVIATION NEEDLES”
cloning error has occurred. 14
shows that cloning is taking place “COURSE DEVIATION
NEEDLES” shows that
cloning is taking place.
In this case, both transceivers automatically return to the
• “ CL-IN” appears automatically in the clone standby condition and cloning must be repeated.
sub transceiver’s display.
25
8 BATTERY PACKS
R DANGER! NEVER immerse battery pack in water. R WARNING! NEVER charge the transceiver during a
If the battery pack becomes wet, be sure to wipe it dry im- lightning storm. It may result in an electric shock, cause a
mediately (particularly the battery terminals BEFORE at- fire or damage the transceiver. Always disconnect the power
taching it to the transceiver). adapter before a storm.
R DANGER! NEVER short the terminals of the bat- CAUTION: To avoid damage to the transceiver, turn the
tery pack. Also, current may flow into nearby metal objects, power OFF while charging.
such as a necklace, etc. Therefore, be careful when carrying
• Recommended temperature range for charging:
with, or placing near metal objects, carrying in handbags,
+10°C ~ +40°C (+50°F ~ +104°F)
etc.
• Use the supplied AC adapter on regular charging. NEVER
CAUTION: NEVER insert battery pack/transceiver use another manufacture’s adapters.
(with the battery pack attached) with wet or soiled into the • Use the specified chargers (BC-119N, BC-121N and
charger. This may result in corrosion of the charger terminals BC-144N). NEVER use another manufacture’s charger.
or damage to the charger. The charger is not waterproof and CAUTION: NEVER connect DC power to the transceiver
water can easily get into it. when installing Alkaline batteries. Such a connection will
If your battery pack seem to have no capacity even after damage the transceiver.
being charged, completely discharge them by leaving the
power ON overnight. Then, fully charge the battery pack D Recycling information (U.S.A. only)
again. If the batteries still do not retain a charge (or very lit-
The product that you have purchased contains a
tle), new battery pack must be purchased. rechargeable battery. The battery is recyclable. At
the end of its life, under various state and local
Turn the transceiver power OFF when charging the battery laws, it may be illegal to dispose of this battery
pack. Otherwise, the battery pack may not fully charge or into the municipal waste stream. Call 1-800-822-8837 for
charge properly. battery recycling options in your area or contact your dealer.
26
BATTERY PACKS 8
To the cigarette
lighter socket
To [DC 11V] Wall charger
To AC outlet
The shape may
differ depending
on the version.
27
8 BATTERY PACKS
w
CAUTION:
Supplied • DO NOT push or force the latch with a screw driver, etc.,
screws to remove it.
• DO NOT bend the latch when the adapter and spacer
are not joined together. This will cause weakening of the
latch plastic.
• Both cases may break the latch and it may not be able
to be reattached.
• BE CAREFUL not to lose the spacer (Spacer B/C) after
removing it from the adapter (Spacer A).
28
BATTERY PACKS 8
ïïRapid charging with the BC-119N+AD-101 ïïRapid charging with the BC-121N+AD-101 1
The optional BC-119N provides rapid charging of the battery The optional BC-121N allows up to 6 battery packs to be
packs. The following are additionally required. charged simultaneously. The following are additionally re-
2
• AD-101 charger adapter. quired. 3
• An AC adapter (may be supplied with BC-119N depending on ver- • Six AD-101 charger adapters.
sions) or the DC power cable (CP-20). • An AC adapter (BC-157) or the DC power cable (OPC-656). 4
The adapter (Spacer A) only is required for IC-A24/A6. When re- The adapter (Spacer A) only is required for IC-A24/A6. When re-
5
moving the spacer (Spacer B/C), push the latch carefully with your moving the spacer (Spacer B/C), push the latch carefully with your 6
finger to remove the spacer (Spacer B/C) from the adapter finger to remove the spacer (Spacer B/C) from the adapter
(Spacer A). See p. 28 for details. (Spacer A). See p. 28 for details. 7
Turn power OFF IC-A24/A6 IC-A24/A6 8
Turn power OFF
BP-209N/BP-210N BP-209N/BP-210N
9
10
AD-99N (supplied
with AD-101)
AD-101 charger adapters are
11
AD-99N (supplied
with AD-101) The AD-101 charger adapter
installed in each slot.
12
is installed in the slot.
13
AC adapter 14
(BC-157:
Purchase
separately) DC power cable (OPC-656)
AC adapter (Connect with the DC power supply;
13.8 V/at least 7 A)
29
9 SPECIFICATIONS
ïïGeneral ïïReceiver
• Frequency coverage (MHz): TX 118.000 to 136.9917 • Receive system: Double conversion
RX 108.000 to 136.9917*1 superheterodyne
WX 161.650 to 163.275*4 • Intermediate frequencies: 1st 46.35 MHz, 2nd 450 kHz
• Mode: 6K00A3E/5K60A3E • Sensitivity
16K0G3E (161.65 to 163.275 MHz)*4 VOR (AM 6 dB S/N): –3 dBµ typical
• Channel spacing: 25 kHz/8.33 kHz COM (AM 6 dB S/N): –6 dBµ typical
• Number of memory channels: 200 (20 CH × 10 BANKS) WX (FM 12 dB SINAD): –13 dBµ typical
• Power supply requirement: Specified battery packs/case or • Squelch sensitivity: AM Less than 0 dBµ
11.0 V DC at the external DC jack (Threshold) FM Less than –5 dBµ*4
• Usable temperature range: –10˚C ~ +60˚C (+14°F ~ +140°F) • Selectivity: 6 dB (More than 7.5 kHz)*2
• Current drain: Tx 1.5 A typical 60 dB (Less than 25 kHz)*2
Rx 70 mA typical (at stand by) 6 dB (Less than 2.778 kHz)*3
300 mA typical (at AF maximum) 60 dB (Less than 7.37 kHz)*3
• Antenna connector: BNC 50 Ω (nominal) • Spurious response: AM More than 60 dB
• Dimensions : 54 (W) × 129.3 (H) × 35.5 (D) mm rejection FM More than 30 dB*4
(projections not included) 2.1 (W) × 5.1 (H) × 1.4 (D) inch • Audio output power: 500 mW typical (at 10% distortion
• Weight: Approximately 180 g (6.35 oz) with an 8 Ω load, 30% modulation)
(Without the battery pack • Noise and hum: More than 35 dB at 30% modulation
and antenna.) • External speaker connector: 3-conductor 3.5 (d) mm (1/8˝)/8 Ω
ïïTransmitter *1: IC-A24 only. (IC-A6 frequency coverage is from 118.000 to 136.9917 MHz.)
• Output power: 5.0 W (PEP) typical *2: at 25 kHz channel spacing.
1.5 W (CW) typical *3: at 8.33 kHz channel spacing.
• Modulation: Low level modulation *4: U.S.A. version only.
• Modulation limiting: 70 to 100%
• Frequency stability: ±1 ppm
• Audio harmonic distortion:
Less than 10% (at 60% modulation)
• Hum and noise ratio: More than 35 dB
• Spurious emissions: M ore than 46 dB (except operating Measurements made in accordance with RTCA.
frequency ±62.5 kHz range)
• Microphone connector: 3-conductor 2.5(d) mm (1/10˝)/ All stated specifications are subject to change without notice
more than 100 kΩ or obligation.
30
SPECIFICATIONS (VFO CHANNEL ID LIST) 9
• Channel spacing: 25 kHz (Actual frequency is displayed.) • Channel spacing: 8.33 kHz/25 kHz 1
Operating Frequency Channel spacing Channel ID Operating Frequency Channel spacing Channel ID
(MHz) (kHz) (Displayed Frequency) (MHz) (kHz) (Displayed Frequency)
2
118.0000 25 118.000 118.0000 25 118.000 3
118.0250 25 118.025 118.0000 8.33 118.005
118.0500 25 118.050 118.0083 8.33 118.010
4
118.0750 25 118.075 118.0167 8.33 118.015 5
118.1000 25 118.100 118.0250 25 118.025
118.0250 8.33 118.030
6
• Channel spacing: 8.33 kHz 118.0333 8.33 118.035 7
118.0417 8.33 118.040
Operating Frequency Channel spacing Channel ID
118.0500 25 118.050
8
(MHz) (kHz) (Displayed Frequency)
118.0000 8.33 118.005
118.0500 8.33 118.055 9
118.0583 8.33 118.060
118.0083 8.33 118.010
118.0667 8.33 118.065
10
118.0167 8.33 118.015
118.0250 8.33 118.030
118.0750 25 118.075 11
118.0750 8.33 118.080
118.0333 8.33 118.035
118.0833 8.33 118.085
12
118.0417 8.33 118.040
118.0500 8.33 118.055
118.0917 8.33 118.090 13
118.1000 25 118.100
118.0583 8.33 118.060
118.1000 8.33 118.105
14
118.0667 8.33 118.065
118.0750 8.33 118.080
118.0833 8.33 118.085
118.0917 8.33 118.090
118.1000 8.33 118.105
These tables show just the display example between 118.0000 MHz
and 118.1000 MHz, not show all frequencies in the band.
31
10 OPTIONS
33
12 SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy while • DO NOT operate the radio without a proper antenna attached, as this
transmitting. This radio is designed for and classified as for may damage the radio and may also cause you to exceed FCC and IC
“Occupational Use Only.” This means it must be used only RF exposure limits. A proper antenna is the antenna supplied with this
during the course of employment by individuals aware of the radio by the manufacturer or an antenna specifically authorized by the
hazards, and the ways to minimize such hazards. This radio manufacturer for use with this radio.
W ARN ING is NOT intended for use by the “General Population” in an • DO NOT transmit for more than 50% of the total radio use time (“50%
uncontrolled environment. duty cycle”). Transmitting more than 50% of the time can cause FCC and
This radio has been evaluated for compliance at the distance of 2.5 cm with IC RF exposure compliance requirements to be exceeded. The radio is
the FCC and IC RF exposure limits for “Occupational Use Only.” In addition, transmitting when “ ” appears on the function display. You can cause
your Icom radio complies with the following Standards and Guidelines with the radio to transmit by pushing the “PTT” switch.
regard to RF energy and electromagnetic energy levels and evaluation of • ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body
such levels for exposure to humans: when transmitting and only use the Icom belt-clips which are listed on
• FCC
KDB Publication 447498 D03, Evaluating Compliance with FCC page 32 when attaching the radio to your belt, or other place, to ensure
Guidelines for Human Exposure to Radio Frequency Electromagnetic FCC and IC RF exposure compliance requirements are not exceeded.
Fields.
• American
National Standards Institute (C95.1-1992), IEEE Standard for The information listed above provides the user with the information needed to
Safety Levels with Respect to Human Exposure to Radio Frequency make him or her aware of RF exposure, and what to do to assure that this
Electromagnetic Fields, 3 kHz to 300 GHz. radio operates within the FCC and IC RF exposure limits of this radio.
• American
National Standards Institute (C95.3-1992), IEEE
Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Interference/Compatibility
Electromagnetic Fields– RF and Microwave. During transmissions, your Icom radio generates RF energy that can possibly
• The following accessories are authorized for use with this product. Use of cause interference with other devices or systems. To avoid such interference,
accessories other than those specified may result in RF exposure levels turn off the radio in areas where signs are posted to do so. DO NOT operate
exceeding the FCC and IC requirements for wireless RF exposure.; Belt the transmitter in areas that are sensitive to electromagnetic radiation such as
Clip (MB-86/103), Speaker Microphone (HM-234), Rechargeable Ni-MH hospitals and blasting sites.
Battery Pack (BP-210N) and Alkaline Battery Case (BP-208N).
• Health
Canada Safety Code 6 - Limits of Human Exposure to Occupational/Controlled Use
Electromagnetic Energy in the Frequency Range from 3 kHz to 300 GHz. The radio transmitter is used in situations in which persons are exposed as a
consequence of their employment provided those persons are fully aware of
the potential for exposure and can exercise control over their exposure.
To ensure that your expose to RF electromagnetic energy is
within the FCC and IC allowable limits for occupational use,
always adhere to the following guidelines:
C AU TIO N
34
INFORMATION EN MATIÈRE DE SÉCURITÉ 12
Votre radio Icom produit une énergie électromagnétique • NE PAS faire fonctionner la radio sans qu'une antenne appropriée y soit
de radiofréquences (RF), en mode de transmission. Cette fixée, car ceci risque d'endommager la radio et causer une exposition
1
radio est conçue pour un «usage professionnel seulement»
et classée comme tel, ce qui signifie qu'elle doit être
supérieure aux limites établies par la FCC et d’IC. L'antenne appropriée
est celle qui est fournie avec cette radio par le fabricant ou une antenne
2
utilisée uniquement dans le cadre d'un travail par des spécialement autorisée par le fabricant pour être utilisée avec cette 3
AVERTISSEMENT personnes conscientes des dangers et des mesures visant radio.
à minimiser ces dangers. Elle N'EST PAS conçue pour une • NE PAS émettre pendant plus de 50% du temps total d'utilisation de 4
«utilisation grand public», dans un environnement non contrôlé. l'appareil («50% du facteur d'utilisation»). Émettre pendant plus de 50%
Cet appareil a été évalué et jugé conforme, à 2,5 cm, aux limites d'exposition du temps total d'utilisation peut causer une exposition aux RF supérieure 5
aux RF de la FCC et d’IC, pour une « utilisation grand public ». En outre, aux limites établies par la FCC et d’IC. La radio est en train d’émettre
votre radio Icom satisfait les normes et directives qui suivent en matière de lorsque le témoin du “ ” s’affiche sur l’écran ACL. La radio émettra si 6
niveaux d'énergie et d'énergie électromagnétique de RF et d'évaluation de vous appuyez sur le bouton du microphone.
tells niveaux en ce qui concerne l'exposition humaine : • TOUJOURS tenir l'antenne éloignée d'au moins 2,5 cm de votre corps 7
• Publication 447498 D03 de la FCC KDB, «Evaluating Compliance au moment d'émettre et utiliser uniquement l'attache pour ceinture
with FCC Guidelines for Human Exposure to Radio Frequency Icom illustrée à la p. 32, lorsque vous attachez la radio à votre ceinture, 8
Electromagnetic Fields». ou à autre chose, de façon à vous assurer de ne pas provoquer une
• Norme de l’American National Standards Institute (ANSI): IEEE C95.1- exposition aux RF supérieure aux limites fixées par la FCC et d’IC. 9
1992 sur les niveaux de sécurité compatibles avec l'exposition humaine
aux champs électromagnétiques de radiofréquences (3 kHz à 300 GHz). Les renseignements ci-dessus fournissent à l'utilisateur toute l'information
10
• Norme de l’ANSI : IEEE C95.3-1992 sur la méthode d’évaluation
recommandée du champ magnétique potentiellement dangereux des
nécessaire sur l'exposition aux RF et sur ce qu'il faut faire pour assurer que
cette radio fonctionne en respectant les limites d'exposition aux RF établies
11
radiofréquences et des micro-ondes.
• Les accessoires qui suivent sont approuvés pour une utilisation avec
par la FCC et d’IC. 12
ce produit. L'utilisation d'accessoires autres que ceux précisés peut Interférence électromagnétique et compatibilité 13
entraîner des niveaux d'exposition aux RF supérieures aux limites En mode de transmission, votre radio Icom produit de l'énergie de RF qui
établies par la FCC et d’IC en matière d'exposition aux RF sans fil.; peut provoquer des interférences avec d'autres appareils ou systèmes. Pour 14
Attache pour ceinture (MB-86/103), microphone haut-parleur (HM-234), éviter de telles interférences, mettez la radio hors tension dans les secteurs
bloc-piles rechargeable au Ni-MH (BP210N) et boiter piles (BP-208N). où une signalisation l’exige. NE PAS faire fonctionner l'émetteur dans des
• Le Code de sécurité 6 de Santé Canada - Les limites d’exposition secteurs sensibles au rayonnement électromagnétique tels que les hôpitaux,
humaine à l’énergie électromagnétique dans la gamme de fréquences les aéronefs et les sites de dynamitage.
de 3 kHz à 300 GHz.
36
TROUBLESHOOTING 14
If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. 1
PROBLEM POSSIBLE CAUSE SOLUTION REF.
2
No power comes on. • The battery is exhausted. • Recharge the battery pack. pp. 26–29
• Bad connection for the battery pack. • Check the connection to the transceiver. p. 1 3
• The CP-20’s fuse is blown. • C heck for the cause, then replace the p. 37 4
CP-20’s fuse to new one.
No sound comes from • Squelch level is too deep. • Set squelch to the threshold point. p. 9 5
the speaker. • Volume level is too low. • Set [VOL] to a suitable level. p. 9
6
Transmitting impossible. • WX channels or NAV band is selected. • Set COM band in frequency mode. p. 8
• The battery is exhausted. • Recharge the battery pack. pp. 26–29 7
Operating frequency or • Lock function is activated. • Push , then push [7• ]. p. 11 8
memory channel can not
be changed. 9
Scan does not start. • All memory channels in the selected bank • S et the “TAG” settings of desired p. 17
are not programmed as “TAG” channels. channels. 10
• Squelch is open. • Set the squelch level to tighten. p. 9
• T here is not more than 2 memorized • Program 2 or more memory channels. p. 16
11
channels. 12
No beep sounds. • Beep tones turned OFF. • P ush , then push [8• BEEP ], and p. 11
rotate [DIAL] to adjust the beep tone 13
level.
14
When using an optional • The side tone function is activated. • Push [PTT], then rotate [DIAL] to set the p. 11
HM-234, your voice monitoring level to ‘ST-0’ (The side tone
hears from the speaker function is OFF).
during transmitting.
ïïCP-20 fuse replacement
If the fuse blows or the receiver stops functioning while
Fuse 8 A
operating with the optional CP-20 cigarette lighter cable,
find the source of the problem if possible, and replace the
damaged fuse with a new rated one (FGB 8 A) as shown
right.
37
INDEX
–A– –E–
About AD-99N.................................................................................28 Entering a desired course...............................................................22
Accessing the 121.5 MHz emergency frequency............................11 EXPLICIT DEFINITIONS.................................................................... i
ACCESSORY ATTACHMENT............................................................1 –F–
AD-101 installation..........................................................................28 Flying to a VOR station....................................................................20
ANL function......................................................................................9 FOR CLASS A UNINTENTIONAL RADIATORS.............................36
Antenna.............................................................................................1 FOREWORD...................................................................................... i
–B– Function display.................................................................................6
BASIC OPERATION..........................................................................8 –G–
BATTERY CASE AND PACKS........................................................32 General............................................................................................30
Battery cautions...............................................................................26 –I–
Battery charging..............................................................................26 IMPORTANT....................................................................................... i
Battery pack replacement..................................................................1 INDEX..............................................................................................38
BATTERY PACKS............................................................................26 –L–
BC-119N+AD-101...........................................................................29 Lock function...................................................................................11
BC-121N+AD-101...........................................................................29 Low battery indicator.......................................................................10
Belt clip..............................................................................................1 –M–
BELT CLIPS.....................................................................................32 Memory channel selection...............................................................12
–C– Memory names................................................................................14
Channel spacing setting....................................................................9 MEMORY OPERATION...................................................................12
CHARGERS....................................................................................32 Memory scan...................................................................................16
Clearing the memory contents........................................................14 MICROPHONE................................................................................32
CLONING........................................................................................25 –O–
Cloning error....................................................................................25 OPC-499 (HEADSET ADAPTER) connection.................................33
Cloning using PC.............................................................................25 Operating the duplex function..........................................................24
COM band scan...............................................................................16 Optional battery case......................................................................27
CP-20 fuse replacement..................................................................37 Optional battery chargers................................................................28
Crosschecking position....................................................................22 OPTIONAL HEADSET CONNECTION...........................................33
–D– OPTIONS........................................................................................32
DC CABLES....................................................................................32 OTHER OPTIONS...........................................................................32
Deletes the stored recall channel....................................................10 –P–
Duplex operation.............................................................................24 Panel description...............................................................................2
PANEL DESCRIPTION......................................................................2
38
INDEX