Professional Documents
Culture Documents
AnchorBolt SSEN1993 Module
AnchorBolt SSEN1993 Module
Reference
EN 1993-1-1:2005
EN 1993-1-8:2005
EN 1992-1-1:2005
ETAG-001, Annex C
CSf
CSw
C1
C2
Pedestal Details:
Material Strengths:
Anchor Bolt Yield Strength (fyb) = 640 N/mm2 EN 1993-1-8, Table 3.1
Anchor Bolt Ultimate Strength (fub) = 800 N/mm2 EN 1993-1-8, Table 3.1
Partial safety factor for bolt (γM2) = 1.25 NA to SS EN 1993-1-8, Table NA.1
Partial safety factor for taking account of the installation safety of an anchor system (γ2) = 1.00 ETAG-001, Annex C - cl 3.2.2.1
Concrete Material Factor for Ultimate limit state, γc = 1.5 NA to SS EN 1992 1-1, Table NA.1
Partial safety factor for concrete cone failure, γMc = γc * γ2 = 1.5 ETAG-001, Annex C - cl 3.2.2.1
Partial safety factor for pull-out failure, γMp = γMc = 1.5 ETAG-001, Annex C - cl 3.2.2.1
Partial safety factor for splitting failure, γMsp = γMc = 1.5 ETAG-001, Annex C - cl 3.2.2.1
Characteristic Cylindrical Strength of Concrete (fck) = 30 N/mm2
Characteristic Cube Strength of Concrete (fck,cube) = 37 N/mm2
Where, Ah = Load bearing area of the head of the fastener = π (φh2 - φ2)/4 = 593.8 mm2
The characteristic resistance of Anchor Bolt in case of Concrete Cone Failure: ETAG-001, Annex C - cl 5.2.2.4
Scr,N = Spacing for ensuring the transmission of the characteristic tensile resistance of a single anchor
915 mm
without spacing and edge effects in case of concrete cone failure = 3 hef =
Ccr,N = Edge distance for ensuring the transmission of the characteristic tensile resistance of a single
457.5 mm
anchor without spacing and edge effects in case of concrete cone failure = 1.5 hef =
A0c,N = Area of concrete of an individual anchor with large spacing and edge distance at the concrete surface
= Scr,N * Scr,N = 837225 mm2
Ac,N = Actual area of concrete cone of the anchorage at the concrete surface, as the concrete
cones of four anchor bolts are overlapping,
Ψs,N = factor accounts disturbance of the stresses in the concrete due = 0.8
to edges of the member, (0.7 + 0.3 .C / Ccr,N ) < = 1 CSw
Ψre,N = The shell spalling factor, accounts the effect of Reinforcement, = 1.0
(0.5 + (hef / 200)) <=1
= 1.0 C1
Ψec,N = factor accounts group effect when different tension CSf
loads acting on the individual anchors of a group
The characteristic resistance of Anchor Bolt in case of Concrete Cone Failure, NRk,c = 178 kN
Design resistance of Anchor Bolt in case of Concrete Cone Failure, NRd,c = NRk,c /γMc = 118.6 kN
The characteristic resistance of Anchor Bolt in case of Concrete Cone Failure: ETAG-001, Annex C - cl 5.2.2.6
where, Ψh,sp = factor to account for the influence of the actual member depth, H, = 1.5
on the splitting resistance for anchors = (H/hef)^(2/3) < =1.5
The characteristic resistance of Anchor Bolt in case of Splitting Failure, NRk,sp = 266.9 kN
Design resistance of Anchor Bolt in case of Splitting Failure, NRd,c = NRk,sp /γMsp = 178 kN