Professional Documents
Culture Documents
Ex-Cell XR2750 Pressure Washer Operation Manual
Ex-Cell XR2750 Pressure Washer Operation Manual
Table of Contents
Safety Guidelines/Definitions...................2 Maintenance...........................................12
Consumer Saftey Information .................2 Storage ...................................................13
Important Safety Instructions...............2-5 Trouble Shooting Guide ...................14-15
Carton Contents.......................................6 Warranty..................................................16
Assembly Instructions ..........................6-7 Español .............................................17-36
Operating Instructions........................7-11
IMPORTANT
Please make certain that the person who is to use this equipment carefully
reads and understands these instructions before operating.
Part No. A00088 Rev. 1 5/21/04
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This
information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS.
To help you recognize this information, we use the symbols below. Please read the manual and
pay attention to these symbols.
HAZARD
A00088 2- ENG
HAZARD
HAZARD
RISK TO BREATHING
HAZARD
RISK TO FLUID
INJECTION
• Injuries can result if system pressure is not • To relieve system pressure, shut off engine,
reduced before attempting maintenance or turn off water supply, and pull gun trigger
disassembly. until water stops flowing.
• Use only hoses and accessories rated for
pressure higher than your pressure
washer's PSI.
3- ENG A00088
HAZARD
HAZARD
HAZARD
HAZARD
RISK OF INJURY OR PROPERTY DAMAGE
WHEN TRANSPORTING OR STORING
A00088 4- ENG
HAZARD
• If proper starting procedure is not • If engine does not start after two pulls,
followed, engine can kickback causing squeeze trigger of gun to relieve pump
serious hand and arm injury. pressure. Pull starter cord slowly until
resistance is felt. Then pull cord rapidly
to avoid kickback and prevent hand or
arm injury.
• The spray gun/wand is a powerful clean- • Keep children away from the pressure
ing tool that could look like a toy to a washer at all times.
child.
• Reactive force of spray will cause • Do not overreach or stand on an unstable
gun/wand to move, and could cause the support. Grip gun/wand firmly with both
operator to slip or fall, or misdirect the hands. Expect the gun to kick when trig-
spray. Improper control of gun/wand can gered.
result in injuries to self and others.
HAZARD
5- ENG A00088
CARTON CONTENTS
English/
Spanish
Operation Nozzle
Chemical Nozzle
Manual Cleaning
Hose Holder
Tool Quick
Connect Formed
Engine Frame Engine Rubber
Nozzles
Manual Covers
and Wheel
Assembly
Bagged Parts
Spray Gun
"Water Vroom"
High Pressure Surface Cleaning Guide
Hose Quick Connect Spray Wand Handle
ASSEMBLY INSTRUCTIONS
1. Place the nozzle holder onto the 4. To Assemble "Water Vroom"
panel (located on the handle surface cleaning guide. NOTE: If
assembly) and push each nozzle not using the "Water Vroom"
holder into place. surface cleaning guide proceed to
step 6.
a. Loosen knob a
(a) and rotate
"J" hook (b)
down and out
of the way.
2. Remove five colored quick connect
b. Slide spray b
nozzles from plastic bag and insert
them into correct grommet on the wand (c)
nozzle holder. NOTE: Nozzles are through
color coded to match colored opening in
nozzles on panel. surface
3. Place handle assembly onto frame, cleaning
depress the snap buttons, and slide guide. c
the handle assembly onto the frame IMPORTANT: Make
until snap buttons snap into place. sure nozzle is removed before
assembling surface cleaning guide.
c. Adjust spray wand to desired
height needed for job to be
performed.
4. Attach high
pressure hose to
gun. Tighten se-
curely.
A00088 6- ENG
d. Snap spray c 6. Connect wand to gun. Tighten
wand (c) into securely.
place on
surface
cleaning guide.
7. Slide the formed rubber covers
e. Rotate "J" onto the handle's on-board hose
hook over b and wand storage.
spray wand
and tighten NOTE: The high pressure pump was
filled with oil at the factory. The oil in
knob securely. a
the high pressure pump was designed
f. See To Use to last the life of the pump. If there is a
Spray Wand paragraph in the problem with the pump contact an
Operation section of this Authorized Service Center.
manual to choose and
assemble the correct nozzle for
the job to be performed.
OPERATING INSTRUCTIONS
Compare the illustrations with your unit to familiarize yourself with the location of
various controls and adjustments. Save this manual for future reference.
Spray
Gun
High
Pressure
Hose
Chemical
Hose
Engine
Quick
Connect
Spray Wand
Surface
Cleaning
Guide
High
Pressure
Pump
Spray Pattern
powerful
intense intense covers wide applies
pinpoint for
Uses cleaning of cleaning of areas of cleaning
very intense
small areas larger areas cleaning solutions
cleaning
Metal or
metal, metal, metal, metal,
concrete
Surfaces * concrete, or concrete, or concrete, concrete,
DO NOT use
wood wood wood, or vinyl wood, or vinyl
on wood
9- ENG A00088
Changing Nozzles on Spray Wand 2. Place other end of chemical hose
DO NOT attempt to with filter on it into container holding
change nozzles chemical/cleaning solution. NOTE:
while pressure washer is running. For every 7 gallons of water
Turn engine off before changing pumped 1 gallon of
nozzles. chemical/cleaning solution will be
1. Pull quick connect coupler back used.
and insert nozzle. 3. Install low pressure (black) nozzle
into quick connect fitting of spray
wand, see How To Use Spray Wand
paragraph in this section.
4. After use of chemicals, place
chemical hose into container of
clean water and draw clean water
through chemical injection system
to rinse system thoroughly. If
2. Release quick connect coupler chemicals remain in the pump it
and twist nozzle to make sure it is could be damaged. Pumps
secure in coupler. damaged due to chemicals will not
Risk Of Injury. be covered under warranty.
Ensure nozzle is NOTE: Chemicals and soaps will not
completely inserted in QC socket, siphon when spray wand is in the high
and QC snap ring is fully engaged pressure setting.
(forward) before squeezing gun
trigger. STARTING
Risk of injection or Prior to starting, refer to your engine
injury to person. Do manual for proper starting
not direct discharge stream toward procedures.
persons, unprotected skin, eyes, or 1. In a well ventilated outdoor area
any pets or animals. Serious injury add fresh, high quality, unleaded
can occur. gasoline with a pump octane
rating of 86 or higher. Do not
HOW TO APPLY CHEMICALS overfill. Wipe up spilled fuel before
AND CLEANING SOLVENTS starting the engine. Refer to
Engine Owners Manual for correct
Applying chemicals or cleaning procedure.
solvents is a low pressure operation.
2. Check engine oil level. See
NOTE: Use only soaps and chemicals
Engine Owners Manual for correct
designed for pressure washer use. Do
procedure.
not use bleach.
3. Verify the filter Filter Screen
To Apply chemicals: screen is in
1. Press chemical Barb water inlet of
hose onto barbed Fitting pump. NOTE:
fitting located near Cone side
high pressure hose faces out.
connection of
pump as shown.