Professional Documents
Culture Documents
Seismic Vs Wind
Seismic Vs Wind
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Three Story Comparison of Seismic and Wind Based on 2018 IBC / 2016 CBC
INPUT DATA
Exposure category (B, C or D, ASCE 7-10 26.7.3) C
Importance factor (ASCE 7-10 Table 1.5-2) Iw = 1.00 for all Category
Basic wind speed (ASCE 7-10 26.5.1 or 2012 IBC) V = 145 mph
Topographic factor (ASCE 7-10 26.8 & Table 26.8-1) Kzt = 1 Flat
Building height to eave he = 25 ft
Building height to ridge hr = 29.5 ft
Building length L = 150 ft
Building width B = 50 ft
Effective area of components (or Solar Panel area) A = 10 ft2
DESIGN SUMMARY
Max horizontal force normal to building length, L, face
Max horizontal force normal to building length, B, face
Max total horizontal torsional load
Max total upward force
ANALYSIS
Velocity pressure
qh = 0.00256 Kh Kzt Kd V2 = 43.83 psf
where: qh = velocity pressure at mean roof height, h. (Eq. 28.3-1 page 298 & Eq. 30.3-1 pag
Kh = velocity pressure exposure coefficient evaluated at height, h, (Tab. 28.3-1, pg 299)
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 250)
h = mean roof height
Note: If the effective area is roof Solar Panel area, the only zone 1, 2 , or 3 apply
PAGE :
DESIGN BY :
REVIEW BY :
ly zone 1, 2 , or 3 apply.
PROJECT : PAGE :
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Three Story Seismic Analysis Based on 2012 IBC / 2013 CBC
Determine Base Shear (Derived from ASCE 7 Sec. 12.8 & Supplement 2)
V = MAX{ MIN [ SD1I / (RT) , SDS I / R ] , MAX(0.044SDSI , 0.01) , 0.5S1 I / R } W
= MAX{ MIN[ 0.38W , 0.15W ] , 0.04W , 0.00W } ^
= 0.15 W, (SD) (for S1 ≥ 0.6 g only)
= 0.11 W, (ASD) = 98.90 kips
Where SDS = 0.96 (ASCE 7 Sec 11.4.4)
SD1 = 0.55 (ASCE 7 Sec 11.4.4)
S1 = 0.54 (ASCE 7 Sec 11.4.1)
R= 6.5 (ASCE 7 Tab 12.2-1)
I= 1 (2012 IBC Tab 1604.5 & ASCE 7 Tab 11.5-1)
Ct = 0.02 (ASCE 7 Tab 12.8-2)
hn = 25.0 ft
x= 0.75 (ASCE 7 Tab 12.8-2)
T = Ct (hn) =
x
0.224 sec, (ASCE 7 Sec 12.8.2.1)
Calculate Vertical Distribution of Forces & Allowable Elastic Drift (ASCE 7, Sec 12.8.3 & 12.8.6)
Where k = 1 for T <= 0.5 d xe,allowable, ASD = Da I / (1.4 Cd), (ASCE 7 Sec 12.8.6)
k = 0.5 T + 0.75 for T @ (0.5 , 2.5) Cd = 4 ,(ASCE 7 Tab 12.2-1)
k = 2 for T >= 2.5 Da = 0.02 hsx, (ASCE 7 Tab 12.12-1)
INPUT DATA
Exposure category (B, C or D, ASCE 7-10 26.7.3) C
Importance factor (ASCE 7-10 Table 1.5-2) Iw = 1.00 for all Category
Basic wind speed (ASCE 7-10 26.5.1 or 2012 IBC) V = 145 mph
Topographic factor (ASCE 7-10 26.8 & Table 26.8-1) Kzt = 1 Flat
Building height to eave he = 17 ft
Building height to ridge hr = 21.5 ft
Building length L = 150 ft
Building width B = 50 ft
Effective area of components (or Solar Panel area) A = 10 ft2
DESIGN SUMMARY
Max horizontal force normal to building length, L, face
Max horizontal force normal to building length, B, face
Max total horizontal torsional load
Max total upward force
ANALYSIS
Velocity pressure
qh = 0.00256 Kh Kzt Kd V2 = 40.83 psf
where: qh = velocity pressure at mean roof height, h. (Eq. 28.3-1 page 298 & Eq. 30.3-1 pag
Kh = velocity pressure exposure coefficient evaluated at height, h, (Tab. 28.3-1, pg 299)
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 250)
h = mean roof height
Note: If the effective area is roof Solar Panel area, the only zone 1, 2 , or 3 apply
PAGE :
DESIGN BY :
REVIEW BY :
ly zone 1, 2 , or 3 apply.
PROJECT : PAGE :
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
Two Story Seismic Analysis Based on 2012 IBC / 2013 CBC
Determine Base Shear (Derived from ASCE 7 Sec. 12.8 & Supplement 2)
V = MAX{ MIN [ SD1I / (RT) , SDS I / R ] , MAX(0.044SDSI , 0.01) , 0.5S1 I / R } W
= MAX{ MIN[ 0.51W , 0.15W ] , 0.04W , 0.00W } ^
= 0.15 W, (SD) (for S1 ≥ 0.6 g only)
= 0.11 W, (ASD) = 75.16 kips
Where SDS = 0.96 (ASCE 7 Sec 11.4.4)
SD1 = 0.55 (ASCE 7 Sec 11.4.4)
S1 = 0.54 (ASCE 7 Sec 11.4.1)
R= 6.5 (ASCE 7 Tab 12.2-1)
I= 1 (2012 IBC Tab 1604.5 & ASCE 7 Tab 11.5-1)
Ct = 0.02 (ASCE 7 Tab 12.8-2)
hn = 17.0 ft
x= 0.75 (ASCE 7 Tab 12.8-2)
T = Ct (hn) =
x
0.167 sec, (ASCE 7 Sec 12.8.2.1)
Calculate Vertical Distribution of Forces & Allowable Elastic Drift (ASCE 7, Sec 12.8.3 & 12.8.6)
Where k = 1 for T <= 0.5 d xe,allowable, ASD = Da I / (1.4 Cd), (ASCE 7 Sec 12.8.6)
k = 0.5 T + 0.75 for T @ (0.5 , 2.5) Cd = 4 ,(ASCE 7 Tab 12.2-1)
k = 2 for T >= 2.5 Da = 0.02 hsx, (ASCE 7 Tab 12.12-1)
INPUT DATA
Exposure category (B, C or D, ASCE 7-10 26.7.3) C
Importance factor (ASCE 7-10 Table 1.5-2) Iw = 1.00 for all Category
Basic wind speed (ASCE 7-10 26.5.1 or 2012 IBC) V = 145 mph
Topographic factor (ASCE 7-10 26.8 & Table 26.8-1) Kzt = 1 Flat
Building height to eave he = 9 ft
Building height to ridge hr = 13.5 ft
Building length L = 150 ft
Building width B = 50 ft
Effective area of components (or Solar Panel area) A = 10 ft2
DESIGN SUMMARY
Max horizontal force normal to building length, L, face
Max horizontal force normal to building length, B, face
Max total horizontal torsional load
Max total upward force
ANALYSIS
Velocity pressure
qh = 0.00256 Kh Kzt Kd V2 = 38.89 psf
where: qh = velocity pressure at mean roof height, h. (Eq. 28.3-1 page 298 & Eq. 30.3-1 pag
Kh = velocity pressure exposure coefficient evaluated at height, h, (Tab. 28.3-1, pg 299)
Kd = wind directionality factor. (Tab. 26.6-1, for building, page 250)
h = mean roof height
Note: If the effective area is roof Solar Panel area, the only zone 1, 2 , or 3 apply
PAGE :
DESIGN BY :
REVIEW BY :
ly zone 1, 2 , or 3 apply.
PROJECT : PAGE :
CLIENT : DESIGN BY :
JOB NO. : DATE : REVIEW BY :
One Story Seismic Analysis Based on 2012 IBC / 2013 CBC
Determine Base Shear (Derived from ASCE 7 Sec. 12.8 & Supplement 2)
V = MAX{ MIN [ SD1I / (RT) , SDS I / R ] , MAX(0.044SDSI , 0.01) , 0.5S1 I / R } W
= MAX{ MIN[ 0.81W , 0.15W ] , 0.04W , 0.00W } ^
= 0.15 W, (SD) (for S1 ≥ 0.6 g only)
= 0.11 W, (ASD) = 39.56 kips
Where SDS = 0.96 (ASCE 7 Sec 11.4.4)
SD1 = 0.55 (ASCE 7 Sec 11.4.4)
S1 = 0.54 (ASCE 7 Sec 11.4.1)
R= 6.5 (ASCE 7 Tab 12.2-1)
I= 1 (2012 IBC Tab 1604.5 & ASCE 7 Tab 11.5-1)
Ct = 0.02 (ASCE 7 Tab 12.8-2)
hn = 9.0 ft
x= 0.75 (ASCE 7 Tab 12.8-2)
T = Ct (hn) =
x
0.104 sec, (ASCE 7 Sec 12.8.2.1)
Calculate Vertical Distribution of Forces & Allowable Elastic Drift (ASCE 7, Sec 12.8.3 & 12.8.6)
Where k = 1 for T <= 0.5 d xe,allowable, ASD = Da I / (1.4 Cd), (ASCE 7 Sec 12.8.6)
k = 0.5 T + 0.75 for T @ (0.5 , 2.5) Cd = 4 ,(ASCE 7 Tab 12.2-1)
k = 2 for T >= 2.5 Da = 0.02 hsx, (ASCE 7 Tab 12.12-1)