Professional Documents
Culture Documents
Ajuste Del Time de La Direccion Cat-988k
Ajuste Del Time de La Direccion Cat-988k
Ajuste Del Time de La Direccion Cat-988k
Previous Screen
Welcome: r405lep
Product: WHEEL LOADER
Model: 988K WHEEL LOADER LWX00696
Configuration: 988K Wheel Loader LWX00001-UP (MACHINE) POWERED BY
C18 Engine
i05374667
Specifications
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Note: To check the steering time, park the machine on a dry, hard, level surface.
Table 1
988K Steering Time
Steering Time for a Full Turn from Stop to Stop (Low Idle) 5.6 ± 0.9 seconds
Table 2
834K Steering Time
Steering Time for a Full Turn from Stop to Stop (High Idle) 3.1 ± 0.3 seconds
Steering Time for a Full Turn from Stop to Stop (Low Idle) 5.7 ± 0.9 seconds
Table 3
836K Steering Time
Item Setting Actual
Steering Time for a Full Turn from Stop to Stop (High Idle) 3.9 ± 0.8 seconds
Steering Time for a Full Turn from Stop to Stop (Low Idle) 6.4 ± 1.0 seconds
Introduction
This Information includes the following adjustment procedure:
Required Tools
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 1/3
17/5/2019 988K Wheel Loader LWX00001-UP (MACHINE) POWERED BY C18 Engine(SEBP5756 - 47) - Documentation
Table 4
Tool Item Qty Part No Description
B 9U-7839 STOPWATCH
Test Preparation
Refer to Testing and Adjusting, "Machine Preparation for Troubleshooting".
With the engine at high idle, the steering time on a 988K Wheel Loader, for a full turn from stop to stop should be 3.4 ± 0.3 seconds. With the engine at low idle,
the steering time for a full turn from stop to stop should be 5.6 ± 0.9 seconds.
With the engine at high idle, the steering time on a 836K Landfill Compactor for a full turn from stop to stop should be 3.9 ± 0.8 seconds. With the engine at low
idle, the steering time for a full turn from stop to stop should be 6.4 ± 1.0 seconds.
With the engine at high idle, the steering time on a 834K Wheel Dozer, for a full turn from stop to stop should be 3.1 ± 0.3 seconds. With the engine at low idle, the
steering time for a full turn from stop to stop should be 5.7 ± 0.9 seconds.
When the service brakes are not applied, the difference between the steering time for a right turn and the steering time for a left turn must not be more than 0.3
second. When the service brakes are applied, the steering time must not increase by more than 0.2 second.
If the difference between the steering time for a full right turn and the steering time for a full left turn is more than 0.3 second, use the "Steering Time - Adjust"
procedure to adjust the steering time:
Illustration 1 g03402272
Steering Control Valve
(1) Control valve spool. (2) Flow balance shims. (3) Springs. (4) Pilot oil port.
1. Remove the fittings from pilot oil port (4) of the steering control valve.
2. To achieve a faster right turn and a slower left turn, add flow balance shims (2).
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 2/3
17/5/2019 988K Wheel Loader LWX00001-UP (MACHINE) POWERED BY C18 Engine(SEBP5756 - 47) - Documentation
3. To achieve a faster left turn and a slower right turn, remove flow balance shims (2).
4. If you have slow turns in both directions at high idle, add 4B-4278 Washers (5) behind the spring.
5. The thickness of each 2J-2866 Shim is 0.25 mm (0.010 inch). The thickness of each 4T-4628 Shim is 0.50 mm (0.020 inch). Two shims (one shim of each
thickness) will change the steering times at high idle by approximately 0.1 second.
6. Install the fittings and the line to pilot oil port (4).
Copyright 1993 - 2019 Caterpillar Inc. Fri May 17 2019 17:09:16 GMT-0400 (hora de Venezuela)
All Rights Reserved.
r405lep
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/… 3/3