Professional Documents
Culture Documents
AQUARIUM HOUSE - 02 - Column Beam Connection Design
AQUARIUM HOUSE - 02 - Column Beam Connection Design
1
Part
Software licensed to
Job Title Ref
By Date29-Jun-19 Chd
Job Information
Engineer Checked Approved
Name:
Date: 29-Jun-19
Print Time/Date: 04/07/2019 01:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 1 of 5
Job No Sheet No Rev
2
Part
Software licensed to
Job Title Ref
By Date29-Jun-19 Chd
GENERAL DATA
Consider hole deformation in bolts : Yes
Is column end : Yes
Consider sheared edges in shapes : Yes
Frame stability considered in analysis : No
Exists opposite connection : No
Consider sheared edges in shapes : Yes
Beam with beveled edges : No
Consider snug-tightened bolts : No
MEMBERS:
Beam
Section = UB406X178X67
Material = STEEL
Beta = 4.95 Slope angle
Support
Section = UC203X203X46
Material = STEEL
CONNECTION(S):
Connection: Extended end plate
Plate
Material = A36
Fy = 0.25 [KN/mm2]
Fu = 0.40 [KN/mm2]
Width = 215.90 [mm]
Thickness = 19.05 [mm]
Bolts
bolt = 3/4" A325 N
g = 88.90 [mm] Transversal spacing
pfi = 38.10 [mm] Distance from bolt centerline to nearer tension flange surface
H0 = 441.86 [mm] Distance to bolt H0
H1 = 351.30 [mm] Distance to bolt H1
Print Time/Date: 04/07/2019 01:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 2 of 5
Job No Sheet No Rev
3
Part
Software licensed to
Job Title Ref
By Date29-Jun-19 Chd
LOADS
Members Load Type V2 V3 M33 M22 Axial
[KN] [KN] [KN*m] [KN*m] [KN]
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Print Time/Date: 04/07/2019 01:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 3 of 5
Job No Sheet No Rev
4
Part
Software licensed to
Job Title Ref
By Date29-Jun-19 Chd
Print Time/Date: 04/07/2019 01:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 4 of 5
Job No Sheet No Rev
5
Part
Software licensed to
Job Title Ref
By Date29-Jun-19 Chd
NOTATION
bcf: Width of column flange
bfb: Beam flange breadth
bp: Plate width
C2: Edge distance increment
c: Vertical bolt spacing
d: Nominal bolt diameter
dbmax: Maximum bolt diameter
dh: Nominal hole dimension
Fyc: Specified minimum yield stress of column material
Fyp: Specified minimum yield stress of plate
g: Transversal gage between bolts
gmax: Maximum bolt gage
gmin: Minimum bolt gage
h0: Distance from the centerline of a compression flange to the tension side outer bolt row
h0: Distance from the centerline of the beam compression flange to the centerline of the 0 tension bo
h1: Distance from the centerline of a compression flange to the tension side inner bolt rows
h1: Distance from the centerline of the beam compression flange to the centerline of the 1 tension bo
HasPlateThickBehaviour: The plate has thick behavior
k1c: Distance from column web centerline to flange toe of fillet
Lemax: Maximum edge distance
Lemin: Minimum edge distance
Lev: Vertical edge distance
Mn: Nominal moment
Mnp: No prying moment
Mpl: End plate or column flange flexural strength
edmin: Minimum edge distance
pf0: Distance from the inside of a beam tension flange to the nearest outside bolt row
pfi: Distance from the inside of a beam tension flange to the nearest inside bolt row
pfmin: Minimum distance from the inside of a beam tension flange to the nearest inside bolt row
Pt: Bolt tensile strength
b: Design factor for bending
Mn: Design or allowable strength
s: Distance from the most inside or outside tension bolt row to the edge of a yield line
smin: Minimum spacing
tp: Thickness of the connected material
tbf: Thickness of the flange
tcf: Thickness of the column flange
tp: Plate thickness
Print Time/Date: 04/07/2019 01:46 STAAD.Pro V8i (SELECTseries 6) 20.07.11.33 Print Run 5 of 5