QuickServe Online | (4310641) ISX15 CM2350 X101 Serviee Manual
IRIPSRCLOO; EXIT; !RIMTYP99; EXIT; IR!spsz6;stm0;exit;
(/qs3/pubsys2/xml/en/manual/43 10841/4310641-titlepage. html)
Preparatory Steps
Page | of 12
AXWARNING A
Batteries can emit explosive gases. To reduce the
possibility of personal injury, always ventilate the
compartment before servicing the batteries. To
reduce the possibility of arcing, remove the
negative (-) battery cable first and attach the
negative (-) battery cable last.
+ Disconnect the batteries. See equipment
manufacturer service information
+ Remove the exhaust gas recirculation (EGR)
crossover tube. Refer to Procedure 011-070 in
Section 11
(/qs3/pubsys2/xml/en/procedures/173/173-011-070-
‘r-prix 13.htm)
+ Remove the rocker lever cover. Refer to Procedure
003-011 in Section 3.
(Iqs3/pubsys2/xmV/en/procedures/173/173-003-011-
tr-prix13.html)
+ Remove the internal actuator wiring harness. Refer
to Procedure 019-083 in Section 19.
(Iqs3/pubsys2/xmV/eniprocedures/173/173-019-083-
| tr-prixt3.htmi
https://quickserve.cummins.com/qs3/portal/service/manual/en/4310641/
07.12.2018QuickServe Online | (4310641) ISX15 CM2350 X101 Service Manual
Remove
Page 2 of 12
There are two rocker lever shafts:
+ Front - valve and brake rocker lever shaft (1)
+ Rear - valve and brake rocker lever shaft (2)
A\CAUTION A
Some valves will not be loose. Do not tighten or
bottom adjusting screw against lever. Engine
damage can occur.
Loosen the valve adjusting screw locknuts on each
rocker lever.
Turn the adjusting screws counterclockwise until the
rocker levers are loose.
AXCAUTION A
Use care when handling shafts. Rocker levers can
fall off the shaft during removal and damage the
levers. |
— —____J
Remove the valve and brake rocker lever shaft
capscrews, and the rocker lever shaft assemblies.
Remove the valve crossheads.
To prevent increased wear, mark each crosshead and
rocker lever shaft assembly as it is removed so it can be
installed back in the original location.
hutps:/quickserve.cummins.com/qs3/portal/service/manual/en/4310641/
07.12.2018QuickServe Online | (4310641) ISX15 CM2350 X101 Service Manual
Disassemble
Page 3 of 12
Note : This procedure is written for an engine
|| equipped with engine brakes. If an engine does
not have engine brakes installed, a spacer is
installed in the place of a brake lever.
Remove the rocker levers and brake levers from the
shafts,
Remove the rocker lever spacers from the shaft, if
present,
Remove the locknuts and the adjusting screws from the
rocker levers.
To prevent increased wear, mark each adjusting screw
|| as it is removed so it can be installed back in the original
rocker lever.
Clean and Inspect for Reuse
AXWARNING A
When using a steam cleaner, wear safety glasses or|
a face shield, as well as protective clothing. Hot
steam can cause serious personal injury.
AXWARNING A
When using solvents, acids, or alkaline materials
for cleaning, follow the manufacturer's
| recommendations for use. Wear goggles and
protective clothing to reduce the possibility of
personal injury.
AXWARNING AV
‘Some solvents are flammable and toxic. Read the
https://quickserve.cummins.com/qs3/portal/service/manual/en/4310641/
07.12.2018