Professional Documents
Culture Documents
D5 A8 Body Interior Parts Removal
D5 A8 Body Interior Parts Removal
Repair Manual
Audi A8 2018 ➤
Body Interior
Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Repair Group
00 - General, Technical Data
68 - Interior Equipment
69 - Passenger Protection, Airbags, Seat Belts
70 - Interior Trim
76 - Camper Cabinets, Shelves, Water Tank
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Technical information should always be available to the foremen and mechanics, because their
careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and
safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a
matter of course, be observed.
Contents
68 - Interior Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1 Storage Compartments and Covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.1 Component Location Overview - Storage Compartment and Covers . . . . . . . . . . . . . . . . 17
1.2 Overview - Driver Side Instrument Panel Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.3 Overview - Steering Column Trim Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.4 Overview - Glove Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.5 Driver Side Instrument Panel Cover, Removing and Installing . . . . . . . . . . . . . . . . . . . . . . 22
1.6 Upper Steering Column Trim Panel, Removing and Installing . . . . . . . . . . . . . . . . . . . . . . 22
1.7 Lower Steering Column Trim Panel, Removing and Installing . . . . . . . . . . . . . . . . . . . . . . 23
1.8 Glove Compartment Handle, Removing and Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.9 Glove Compartment Handle Lock Cylinder, Removing and Installing . . . . . . . . . . . . . . . . 25
1.10 Glove Compartment, Removing and Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.11 Glove Compartment Lid, Removing and Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.12 Glove Compartment Lid Damping Element, Removing and Installing . . . . . . . . . . . . . . . . 29
2 Extra Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2.1Protected
Overview
by copyright.-Copying
Sun Visors
for private or. commercial
. . . . . . purposes,
. . . . . .in.part
. . or. in. .whole,
. . . is. not
............................. 30
2.2 with Overview
respect to the correctness of information in this document. Copyright by AUDI AG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Sun Shade . . . . . . . . . . . . . . . . . . . . . . . 31
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Contents i
Audi A8 2018 ➤
Body Interior - Edition 10.2018
ii Contents
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Contents iii
Audi A8 2018 ➤
Body Interior - Edition 10.2018
iv Contents
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Contents v
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
vi Contents
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1. Safety Precautions 1
Audi A8 2018 ➤
Body Interior - Edition 10.2018
WARNING
Caution
WARNING
1. Safety Precautions 3
Audi A8 2018 ➤
Body Interior - Edition 10.2018
WARNING
WARNING
anyone.
♦ When connecting a belt tensioner, all mechanical parts, in‐
cluding those in the three-point seat belt, must be secured
correctly. If it is not possible to connect the belt tensioner be‐
cause of insufficient space, the seat belt webbing must be
rolled up completely prior to connection. In this case there is
no increased safety risk, if all other safety instructions are fol‐
lowed. This particularly includes the notes regarding the dis‐
connection of the battery and the static discharging of the
technician prior to connecting the belt tensioner.
♦ Even after a crash, it is possible that the belt tensioner ignited,
but the seat belt force limiter did NOT. Treat these components
as if they had not ignited.
1. Safety Precautions 5
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1. Safety Precautions 7
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Caution
1. Safety Precautions 9
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Inspection Points
♦ Check the seat belt webbing. Refer to
⇒ “1.16 Seat Belt Webbing, Checking”, page 12 .
♦ Check the automatic belt retractor (locking function). Refer to
⇒ “1.17 Automatic Belt Retractor (Locking Function), Check‐
ing”, page 12 .
♦ Visual inspection of the seat belt latch. Refer to
⇒ “1.18 Seat Belt Latch, Visually Inspecting”, page 13 .
♦ Belt latch function test. Refer to
⇒ “1.19 Seat Belt Latch, Function Test”, page 13 .
♦ Check the seat belt relays and belt tongue. Refer to
⇒ “1.20 Seat Belt Relays and Belt Tongue, Checking”,
page 13 .
♦ Check the fasteners and mounting points. Refer to
⇒ “1.21 Fasteners and Mounting Points, Checking After a Col‐
lision”, page 14 .
♦ Check the child seat restraint function for additional child seats
(not for the driver safety belt). Refer to
⇒ “1.22 Seat Belt for Child Seat, Checking Child Seat Restraint
1. Safety Precautions 11
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Test 1
– Pull the seat belt webbing out of the automatic belt retractor
with a firm jerk.
• No locking effect - replace the entire seat belt with seat belt
latch.
• If difficulties are experienced when pulling out or retracting
belt, first check whether position of the belt retractor has been
altered.
• The second locking function is initiated by change in vehicle
velocity (vehicle-dependent locking function).
Test 2
• For safety reasons, road test should be carried out on traffic-
free stretch to ensure that other drivers/pedestrians etc. are
not endangered.
– Fasten the seat belt.
– Accelerate the vehicle to 20 km/h and then perform a hard
braking maneuver with the foot brake.
• Replace the entire seat belt with the seat belt latch if the seat
belt is not locked by locking mechanism during the braking
procedure.
CAUTION
A malfunctioning seat belt increases the risk of injury.
– Never use lubricant to eliminate noise or stiffness at the seat
belt latch buttons.
1. Safety Precautions 13
Audi A8 2018 ➤
Body Interior - Edition 10.2018
WARNING
1. Safety Precautions 15
Audi A8 2018 ➤
Body Interior - Edition 10.2018
2 Repair Information
⇒ “2.1 Contact Corrosion”, page 16
⇒ “2.2 Line Routing and Securing”, page 16
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
68 – Interior Equipment
1 Storage Compartments and Covers
⇒ “1.1 Component Location Overview - Storage Compartment
and Covers”, page 17
⇒ “1.2 Overview - Driver Side Instrument Panel Cover”,
page 19
⇒ “1.3 Overview - Steering Column Trim Panel”, page 20
⇒ “1.4 Overview - Glove Compartment”, page 21
⇒ “1.5 Driver Side Instrument Panel Cover, Removing and Instal‐
ling”, page 22
⇒ “1.6 Upper Steering Column Trim Panel, Removing and Instal‐
ling”, page 22
⇒ “1.7 Lower Steering Column Trim Panel, Removing and Instal‐
ling”, page 23
⇒ “1.8 Glove Compartment Handle, Removing and Installing”,
page 24
⇒ “1.9 Glove Compartment Handle Lock Cylinder, Removing and
Installing”, page 25
⇒ “1.10 Glove Compartment, Removing and Installing”,
page 26
⇒ “1.11 Glove Compartment Lid, Removing and Installing”, page
29
⇒ “1.12 Glove Compartment Lid Damping Element, Removing
and Installing”, page 29
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
5 - Bolt
❑ 3 Nm
6 - Center Instrument Panel
Cover
❑ Overview. Refer to
⇒ “4.1 Overview - Instru‐
ment Panel”,
page 190 .
7 - Driver Side Instrument Pan‐
el Cover
❑ There are different ver‐
sions. Refer to the Parts
Catalog for the alloca‐
tion.
❑ Removing and Instal‐
ling. Refer to ⇒ “1.5 Driver Side Instrument Panel Cover, Removing and Installing”, page 22 .
8 - Bolt
❑ 3 Nm
❑ Quantity: 2
11 - Glove Compartment
❑ There are different versions. Refer to the Parts Catalog for the allocation.
❑ Removing and Installing. Refer to ⇒ “1.10 Glove Compartment, Removing and Installing”, page 26 .
12 - Damping Element
❑ For the glove compartment lid
❑ With Glove Compartment Lamp Switch - E26-
❑ Removing and Installing. Refer to
⇒ “1.12 Glove Compartment Lid Damping Element, Removing and Installing”, page 29 .
13 - Hinge Pin
❑ For the dampening mechanism
14 - Bolt
❑ Quantity: 2
❑ 3 Nm
15 - Vent
❑ For glove compartment cooling
16 - Gap Cover
Installing
Install in reverse order of removal and note the following:
– Next engage the front upper steering column trim panel in the
pins -arrow A- of the lower steering column trim panel.
– Clip in the retaining tab from the upper steering column trim
panel in the lower steering column trim panel -arrow B-.
– Pay attention that the steering column trim panels engage
correctly in each other.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.3 Overview - Steering Column Trim Panel”, page 20 .
Removing
– Move the steering wheel as far to the rear and down as pos‐
sible. Use the full steering column adjustment range for this.
– Turn the steering wheel counter-clockwise 90° from the
straight position.
– Lift the upper steering column trim pane -1- using the -
T10383/2- or a small flat-head screwdriver carefully from the
lower steering column trim -arrow A-.
– Turn the steering wheel back 180° and repeat the procedure
on the opposite side -arrow B-.
– Disengage the upper steering column trim panel on the lower
steering column trim panel and move upward to the side.
Installing
Install in reverse order of removal and note the following:
– Next engage the front upper steering column trim panel in the
pins -arrow A- of the lower steering column trim panel.
– Clip in the retaining tab from the upper steering column trim
panel in the lower steering column trim panel -arrow B-.
– Pay attention that the steering column trim panels engage
correctly in each other.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.3 Overview - Steering Column Trim Panel”, page 20 .
Removing
– Insert the -T10383/1- carefully between the glove compart‐
ment handle and the glove compartment lid.
– Push the glove compartment handle -1- with the -T10383/1-
out of the glove compartment lid -arrow A- and hold it ten‐
sioned.
– Through the opening on the glove compartment lid release
-arrow B- the hooks doe the glove compartment handle using
the - T40011- and guide the -T40011- back out.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
NOTICE
Improper handling increases the risk of destroying the lock cyl‐
inder.
The retainers and pressure springs could fall out.
– Remove and install the lock cylinder only with the key inser‐
ted correctly.
Installing
– Insert the key -3- into the new lock cylinder -2-.
– Remove the protective cap from the new lock cylinder.
– Insert the lock cylinder into the glove compartment handle
-1- until it engages. Pay attention to the installation position of
the pin.
• The pin -arrow- on the lock cylinder points upward.
Further installation is the reverse order of removal.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
– If there is a DTC memory entry, the with Guided
respectFault Findingof information in this document. Copyright by AUDI AG.
to the correctness
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Remove the hinge pins -3- for the glove compartment lid
damping mechanism.
– Pry out the glove compartment lid hinge pin -1- with a flat-head
screwdriver (or another suitable tool) in the direction of the
-arrow- and remove using pliers.
– If the hinge pin cannot be removed, drive out the hinge pin in
the direction of the -arrow- using a punch
– Repeat the process on the opposite side.
– Remove the glove compartment lid -2- from the glove com‐
partment.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.4 Overview - Glove Compartment”, page 21 .
2 Extra Equipment
⇒ “2.1 Overview - Sun Visors”, page 30
⇒ “2.2 Overview - Sun Shade”, page 31
⇒ “2.3 Sun Visor, Removing and Installing”, page 31
⇒ “2.4 Sun Visor Center Support, Removing and Installing”, page
32
⇒ “2.5 Sun Shade, Removing and Installing”, page 32
⇒ “2.6 Roof Grab Handle, Removing and Installing”, page 34
1 - Expanding Caps
❑ Clipped into the sun vi‐
sor
❑ Press until it engages
completely
2 - Roof Grab Handle
❑ Removing and Instal‐
ling. Refer to
⇒ “2.6 Roof Grab Han‐
dle, Removing and In‐
stalling”, page 34 .
❑ Press until it engages
completely
3 - Expanding Caps
❑ Only unclip up to the
lock position, but do not
remove completely
❑ Press until it engages
completely
4 - Center Bracket
❑ For the sun visor
❑ Removing and Instal‐
ling. Refer to
⇒ “2.4 Sun Visor Center
Support, Removing and
Installing”, page 32 .
❑ Do not damage spread‐
er clips when inserting
5 - Expanding Cap
❑ Clipped into the sun vi‐
sor center support
6 - Sun Visor
❑ Removing and Instal‐
ling. Refer to ⇒ “2.3 Sun Visor, Removing and Installing”, page 31 .
❑ Engage in the sun visor mount in the opening in the body
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Expanding Clip
❑ Quantity: 2
❑ Remove using the Pliers
- T40172C-
2 - Cover
❑ For the sun shade guide
rail
❑ Quantity: 2
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
❑ Removing and Instal‐ permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
ling. Refer to with respect to the correctness of information in this document. Copyright by AUDI AG.
⇒ “6.13 D-Pillar Trim
Panel, Removing and
Installing”, page 232 .
❑ Engage into the guide
rail and press on it until
it engages
3 - Clip
❑ Quantity: 2
❑ Insert into the guide rail
❑ Replace damaged or
deformed clips
4 - Guide Rail
❑ Quantity: 2
❑ Remove the clips that
are still in the mounting
points on the body using
the Omega Clip Tool -
T40280- .
❑ Removing and Instal‐
ling. Refer to
⇒ “2.5 Sun Shade, Re‐
moving and Installing”,
page 32 .
❑ Mount it on the sun
shade and press on it until it audibly latches into place
5 - Sunlight Photo Sensor - G914-
6 - Sun Shade
❑ Removing and Installing. Refer to ⇒ “2.5 Sun Shade, Removing and Installing”, page 32 .
❑ Clip into the back part of the rear shelf
❑ Install the sun shade with rear shelf in the rear window frame and tighten it down
2. Extra Equipment 31
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Removing
– Unclip the sun visor mount expanding caps -1- -arrow- by slid‐
ing the -VAS6416- just approximately 1 mm under the cap.
TIP:
If the -VAS6416- is inserted farther, it will be located under the
sun visor. It is then not possible to pry out the expanding cap.
Removing
– Remove the rear shelf front section. Refer to
⇒ “6.15 Rear Shelf, Removing and Installing”, page 235 .
– Remove the Subwoofer - R211- . Refer to ⇒ Communication;
Rep. Gr. 91 ; Sound System; Component Location Overview
- Sound System .
– Remove the Rear Sunlight Photo Sensor - G914- . Refer to ⇒
Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Addi‐
tional Components for Control and Regulation .
– Unclip the sun shade guide rail -1- using the -80 - 200-
-arrows-.
– Pivot the guide rail slightly inward and carefully disengage by
turning the hooks -2- with a small flat-head screwdriver.
– Remove the guide rail upward from the connecting piece on
the sun shade.
– Repeat the process on the opposite side.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Slightly lift the sun shade -1- and pull it forward out of the
mount -arrows-, to do so push the insulation mat to the side.
– Carefully remove the sun shade from the vehicle.
2. Extra Equipment 33
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Installing
Install in reverse order of removal and note the following:
– Carefully install the guide rail -1- into the connector -2- from
the sun shade -arrow-.
• The sun shade guide must run into the guide rail without the
connecting piece being offset.
– Perform a function test after installing.
• The sun shade must have ease of movement in the guide rail.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.2 Overview - Sun Shade”, page 31 .
NOTICE
Improper handling increases the risk of destroying the roof grab
handle.
It is possible that the silicone brake and spring fall out.
– Unclip the expanding cap only to the lock position.
– Insert the angled screwdriver -4- in the gap behind the ex‐
panding cap -2-.
– Pivot the angled screwdriver -arrow-, until the expanding cap
slides audibly into the lock position.
– Repeat the procedure on the second expanding cap -3-.
– Remove the roof grab handle -1- from the opening in the body.
– Leave the expanding caps in the lock position in the roof grab
handle.
Installing
Install in reverse order of removal and note the following:
– Insert the grab handle into the opening in the body.
• There should no longer be a gap between the handle and the
roof trim panel.
– Push in the expanding caps.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Sun Visors”, page 30 .
3 Center Console
⇒ “3.1 Overview - Center Console”, page 35
⇒ “3.2 Center Console Rear Trim, Removing and Installing”, page
40
⇒ “3.3 Center Console Cover, Removing and Installing”,
page 41
⇒ “3.4 Center Console Insert, Removing and Installing”,
page 43
⇒ “3.5 Front Center Console Storage Compartment, Removing
and Installing”, page 44
⇒ “3.6 Center Console Trim Panel, Removing and Installing”,
page 45
⇒ “3.7 Center Console, Removing and Installing”, page 46
⇒ “3.8 Center Console Decorative Trim, Removing and Installing”,
page 48
⇒ “3.9 Cupholder, Removing and Installing”, page 49
⇒ “3.10 Rear Center Console Storage Compartment, Removing
and Installing”, page 50
⇒ “3.11 Rear Center Console Vent, Removing and Installing”,
page 51
⇒ “3.12 Folding Tray Table in Rear Center Console, Removing
and Installing”, page 51
⇒ “3.13 Center Console Bracket, Removing and Installing”, page
52
3. Center Console 35
Audi A8 2018 ➤
Body Interior - Edition 10.2018
11 - Bolt
❑ Quantity: 2
❑ 3 Nm
12 - Rear Vent
❑ Removing and Installing. Refer to
⇒ “3.11 Rear Center Console Vent, Removing and Installing”, page 51 .
❑ Replace damaged or deformed clips
❑ Insert and press in all the way into the installation opening
3. Center Console 37
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1 - Front Bracket
❑ For the rear center con‐
sole
❑ Removing and Instal‐
ling. Refer to
⇒ “3.13.2 Rear Center
Console Bracket, Re‐
moving and Installing”,
page 53 .
2 - Bolt
❑ Quantity: 2
❑ 5 Nm
3 - Rear Center Console
❑ Removing and Instal‐
ling. Refer to
⇒ “3.7.2 Rear Center
Console, Removing and
Installing”, page 47 .
4 - Bolt
❑ Quantity: 4
❑ 3 Nm
5 - Bracket
❑ For the front center con‐
sole
❑ Removing and Instal‐
ling. Refer to
⇒ “3.13.1 Front Center
Console Bracket, Re‐ Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
moving and Installing”, permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
page 52 . with respect to the correctness of information in this document. Copyright by AUDI AG.
6 - Bolt
❑ Quantity: 4
❑ 5 Nm
7 - Bolt
❑ Quantity: 4
❑ 3 Nm
8 - Front Center Console
❑ Removing and Installing. Refer to ⇒ “3.7.1 Front Center Console, Removing and Installing”, page 46 .
9 - Side Trim Panel
❑ For the front center console
❑ Quantity: 2
❑ Removing and Installing. Refer to
⇒ “3.6.1 Front Center Console Trim Panel, Removing and Installing”, page 45 .
❑ Engage in the center console and push forward until it stops
10 - Bolt
❑ Quantity: 2
❑ 5 Nm
11 - Bolt
❑ Quantity: 4
❑ 3 Nm
12 - Rear Trim
❑ For the front center console
3. Center Console 39
Audi A8 2018 ➤
Body Interior - Edition 10.2018
4-Seater:
– Slightly open the storage compartment cover in the rear center
console.
– Unclip the trim -3- from the center console -arrows- using the
-3409- or by hand, to do so push the trim panels -1 and 2-
slightly to the side for the rear center console.
– Remove the trim from the center console toward the rear.
TIP:
If the trim -1- cannot be removed, remove the rear vent in the
center console. Refer to
⇒ “3.11 Rear Center Console Vent, Removing and Installing”,
page 51 .
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.1 Overview - Center Console”, page 35 .
3. Center Console 41
Audi A8 2018 ➤
Body Interior - Edition 10.2018
3. Center Console 43
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Installing
Install in reverse order of removal and note the following:
– Check before installing if the rubber caps -1 and 2- are dam‐
aged and are seated correctly.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.1 Overview - Center Console”, page 35 .
Removing
– Remove the front center console insert. Refer to
⇒ “3.4 Center Console Insert, Removing and Installing”, page
43 .
– Remove the front center console side trim panels. Refer to
⇒ “3.6.1 Front Center Console Trim Panel, Removing and In‐
stalling”, page 45 .
– Remove the rear trim in the front center console. Refer to
⇒ “3.2 Center Console Rear Trim, Removing and Installing”,
page 40 .
Trim, Removing:
– Unclip the trim -1- upward with a small flat-head screwdriver
-arrows-.
– Disengage and remove the lower trim from the fold-out com‐
partment.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.1 Overview - Center Console”, page 35 .
3. Center Console 45
Audi A8 2018 ➤
Body Interior - Edition 10.2018
stalling”, page 46 .
with respect to the correctness of information in this document. Copyright by AUDI AG.
3. Center Console 47
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Trim, Removing: Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
– Open the cover for the cupholder.
with respect to the correctness of information in this document. Copyright by AUDI AG.
3. Center Console 49
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Trim, Removing:
– Open the cover for the cupholder.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
– Release the catch through the permitted
opening -arrow
unless A- with
authorised a AG.
by AUDI small
AUDI AG does not guarantee or accept any liability
flat-head screwdriver and at the with
same time
respect push
to the the trim
correctness up‐ in this document. Copyright by AUDI AG.
of information
ward -arrow B-.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.1 Overview - Center Console”, page 35 .
– Pry out the storage compartment -1- from the center console
using the -3409- -arrows-.
– Remove the storage compartment from the center console.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.1 Overview - Center Console”, page 35 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
3. Center Console 51
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
3. Center Console 53
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1 - Lower Cover
❑ For the rear center arm‐
rest
❑ Removing and Instal‐
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
ling. Refer topermitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Removing
– Remove the front cover for the rear center armrest. Refer to
⇒ “5.5 Rear Center Armrest Cover, Removing and Installing”,
page 59 .
– Remove the spacer wedge for the rear center armrest cover.
Refer to
⇒ “5.3 Rear Center Armrest Storage Compartment, Removing
and Installing”, page 58 .
– Remove the trim -1- for the center armrest insert from the cen‐
ter armrest using the -T10383/1- or the -3409- -arrows-.
– Disengage and remove the remaining retainers of the center
console insert trim.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “5.1 Overview - Rear Center Armrest”, page 56 .
– Disengage the gap cover -1- from the lower cover -arrows-.
– Remove the lower cover -1- for the center armrest from the
center armrest using the -T10383/1- or the -3409- -arrows-.
– Detach and remove the center armrest cover.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “5.1 Overview - Rear Center Armrest”, page 56 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
5.6 Rear Center Armrest Decorative Trim,
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Unclip the center armrest decorative trim -1- from the center
armrest -arrows- with the -3409- .
– Disengage the decorative trim from the center armrest and
remove.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “5.1 Overview - Rear Center Armrest”, page 56 .
1 - Front Cover
❑ For the mirror base
❑ Press on until it engages
audibly
2 - Clamp
❑ For the interior rearview
mirror
❑ Replace after removing
the interior rearview mir‐
ror Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
3 - Bolt with respect to the correctness of information in this document. Copyright by AUDI AG.
❑ Quantity: 2
❑ 1.5 Nm
4 - Rear Cover
❑ For the mirror base
❑ For the interior rearview
mirror without optional
equipment
❑ Press on until it engages
audibly
5 - Retaining Plate
❑ For the interior rearview
mirror
❑ Attached to the wind‐
shield
6 - Cover
❑ For the control module
sensor system
❑ For the interior rearview
mirror with optional
equipment
❑ Press on until it engages
audibly
7 - Rear Cover
❑ For the mirror base
❑ For the interior rearview mirror with optional equipment
❑ Press on until it engages audibly
8 - Interior Rearview Mirror
❑ Automatic dimming interior rearview mirror: the glass of the interior rearview mirror is comprised of sev‐
eral layers and contains an electrolyte fluid. If the mirror glass is broken pay attention to escaping
electrolyte fluid.
❑ Equipment version: with integrated Automatic High Beam Assist Control Module - J844-
❑ The Automatic High Beam Assist Control Module - J844- cannot be replaced separately. Replace the
interior rearview mirror if faulty
❑ Removing and Installing. Refer to ⇒ “6.2 Interior Rearview Mirror, Removing and Installing”, page 62 .
❑ Replace the clip after removing
Installing
Install in reverse order of removal and note the following:
– Replace the clip -2- or -5- after removing the interior rearview
mirror. Refer to the Parts Catalog for the allocation.
– Position the interior rearview mirror tilted 20° with respect to
the installation position.
– Turn the interior rearview mirror clockwise until it stops.
• If the interior rearview mirror with integrated Automatic High
Beam Assist Control Module - J844- is replaced select the
“Replace control module” function for the respective control
module using the Vehicle Diagnostic Tester ⇒ Vehicle diag‐
nostic tester Diagnostic .
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.1 Overview - Interior Rearview Mirror”, page 61 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Test Sequence
– Cover the photosensor -1- on the housing side.
– Shine a light source, such as a flashlight, in the mirror on the
mirror side of the photosensor -2-.
• The interior rearview mirror must dim within a short period of
time.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
7 Special Tools
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
♦ Pliers - T40172A- withpermitted
-T40172/2-
unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
7. Special Tools 69
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1. Seat Belts 71
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Bolt
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
❑ 40 Nm
2 - Automatic Belt Retractor
with Electric Seat Belt Ten‐
sioner and Electric Seat Belt
Force Limiter
❑ with
♦ Left Front Seat Belt Ten‐
sioner Control Module -
J854- / Right Front Seat
Belt Tensioner Control
Module - J855-
♦ Driver Belt Force Limiter -
G551- / Front Passenger
Belt Force Limiter - G552-
♦ Driver Seat Belt Tensioner
Igniter 1 - N153- / Front
Passenger Seat Belt Ten‐
sioner Igniter 1 - N154-
❑ The Left Front Seat Belt
Tensioner Control Mod‐
ule -J854- / Right Front
Seat Belt Tensioner
Control Module -J855-
must be adapted after
replacing the automatic
belt retractors using the
Vehicle Diagnostic
Tester .
❑ Removing and Instal‐
ling. Refer to
⇒ “1.7 Front Three-Point
Seat Belt, Removing
and Installing”, page 81 .
3 - Connector
❑ For
♦ Driver Belt Force Limiter - G551-
♦ Front Passenger Belt Force Limiter - G552-
4 - Connector
❑ For
♦ Driver Seat Belt Tensioner Igniter 1 - N153- Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
♦ Front Passenger Seat Belt Tensioner Igniter 1 - with
N154-
respect to the correctness of information in this document. Copyright by AUDI AG.
1. Seat Belts 73
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Bolt
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
❑ 40 Nm
2 - Bolt Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
❑ Replace the bolt if it was with respect to the correctness of information in this document. Copyright by AUDI AG.
removed because of an
accident when the seat
belt was buckled.
❑ 40 Nm
3 - Automatic Belt Retractor
❑ with
♦ Driver Side Rear Seat Belt
Tensioner Igniter - N196-
♦ Passenger Side Rear Seat
Belt Tensioner Igniter -
N197-
❑ Removing and Instal‐
ling. Refer to
⇒ “1.8.1 Outer Rear
Three-Point Seat Belt,
Removing and Instal‐
ling”, page 83 .
4 - Seat Belt Guide
❑ Removing and Instal‐
ling. Refer to
⇒ “1.8.1 Outer Rear
Three-Point Seat Belt,
Removing and Instal‐
ling”, page 83 .
5 - Bolt
❑ 27 Nm
6 - Connector
❑ For
♦ Driver Side Rear Seat Belt Tensioner Igniter - N196-
♦ Passenger Side Rear Seat Belt Tensioner Igniter - N197-
7 - Belt End Fitting
❑ Removing and Installing. Refer to
⇒ “1.12 Outer Rear Belt End Fitting, Removing and Installing”, page 87 .
1. Seat Belts 75
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1 - Bolt
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
❑ 40 Nm
2 - Seat Frame
3 - Bolt
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
❑ 40 Nm
4 - Nut
❑ 27 Nm
5 - Rear Seat Belt Tensioner
❑ with
♦ Driver Side Rear Seat Belt
Tensioner Igniter 2 - N749-
♦ Passenger Side Rear Seat
Belt Tensioner Igniter 2 -
N750-
❑ Removing and Instal‐
ling. Refer to
⇒ “1.13 Rear Seat Belt
Tensioner, Removing
and Installing”,
page 88 .
6 - Connector
❑ For
♦ Driver Side Rear Seat Belt
Tensioner Igniter 2 - N749-
♦ Passenger Side Rear Seat Belt Tensioner Igniter 2 - N750-
7 - Bolt
❑ 27 Nm
8 - Seat Belt Guide
❑ Removing and Installing. Refer to
⇒ “1.8.1 Outer Rear Three-Point Seat Belt, Removing and Installing”, page 83 .
9 - Connector
❑ For
♦ Left Rear Seat Belt Tensioner Control Module - J1097-
♦ Right Rear Seat Belt Tensioner Control Module - J1098-
10 - Connector Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
❑ For permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
♦ Driver Side Rear Seat Belt Tensioner Igniter - N196-
♦ Passenger Side Rear Seat Belt Tensioner Igniter - N197-
11 - Automatic Belt Retractor
❑ with
1. Seat Belts 77
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1 - Front Seat
2 - Front Seat Belt Latch
❑ with
♦ Driver Seat Belt Switch -
E24-
♦ Front Passenger Seat Belt
Switch - E25-
❑ Removing and Instal‐
ling. Refer to
⇒ “1.15 Front Seat Belt
Latch, Removing and
Installing”, page 91 .
❑ Replace the seat belt
latch if the belt tensioner
has deployed with the
belt buckled
3 - Connector
4 - Cable Holder
❑ Clip into the seat frame
5 - Bolt
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
❑ 33 Nm
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Nut
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled.
❑ 40 Nm
2 - Left Seat Belt Latch
❑ Rest of World equip‐
ment/market version:
with Driver Side Second
Row Seat Belt Switch -
F390-
❑ Allocation. Refer to the
Parts Catalog.
❑ Removing and Instal‐
ling. Refer to
⇒ “1.16.1 Rear Left /
Right Seat Belt Latch,
Removing and Instal‐
ling”, page 92 .
❑ Always replace if the
belt tensioner has de‐
ployed when the belt is
buckled
❑ Align with the direction
of travel when bolting it
on
❑ The locating pin on the
floor panel must be in
the opening on the seat
belt latch bolting surface
3 - Threaded Pins
4 - Locating Pins
5 - Nut
❑ Replace the bolt if it was
removed because of an accident when the seat belt was buckled.
❑ 40 Nm
6 - Center/Right Seat Belt Latch
❑ Rest of World equipment/market version: with
♦ Center Second Row Seat Belt Switch - F391-
♦Protected
Passenger Side Second Row Seat Belt Switch - F392-
by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
❑ Allocation.
with respect to the Refer to
correctness the Parts
of information Catalog.
in this document. Copyright by AUDI AG.
1. Seat Belts 79
Audi A8 2018 ➤
Body Interior - Edition 10.2018
7 - Connector
❑ Only Rest of World equipment/market version:
❑ For
♦ Center Second Row Seat Belt Switch - F391-
♦ Passenger Side Second Row Seat Belt Switch - F392-
8 - Center Rear Belt End Fitting
❑ For center belt
❑ Removing and Installing. Refer to
⇒ “1.16.1 Rear Left / Right Seat Belt Latch, Removing and Installing”, page 92 .
9 - Threaded Pins
10 - Locating Pins
11 - Connector
❑ Only Rest of World equipment/market version:
❑ For Driver Side Second Row Seat Belt Switch - F390-
1 - Bolt
❑ Replace the bolt if it was
removed because of an
accident when the seat
belt was buckled. permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
❑ 33 Nm with respect to the correctness of information in this document. Copyright by AUDI AG.
2 - Washer
❑ Only for 4 seats
3 - Locating Pins
4 - Threaded Pins
5 - Center Seat Belt Latch
❑ Only for 5 seats
❑ With Center Second
Row Seat Belt Switch -
F391-
❑ Removing and instal‐
ling, right single seat.
Refer to ⇒ Seats; Rep.
Gr. 72 ; Rear Seats;
Bench Seat / Single
Seats, Removing and
Installing .
❑ Always replace if the
belt tensioner has de‐
ployed when the belt is
buckled
❑ Align with the direction
of travel when bolting it
on
❑ The locating pin on the
floor panel must be in
the opening on the seat
belt latch bolting surface
6 - Connector
❑ Only Rest of World equipment/market version:
1. Seat Belts 81
Audi A8 2018 ➤
Body Interior - Edition 10.2018
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Disconnect the connector -1- for the seat belt force limiter to
do so remove the connector lock.
– Push the release to disconnect the seat belt tensioner control
module connector -2-.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
– Remove the bolts -arrows-
permitted and then
unless authorised remove
by AUDI AG. AUDI the
AGautomatic beltor accept any liability
does not guarantee
retractor -4- from
withthe mount.
respect to the correctness of information in this document. Copyright by AUDI AG.
– Pull the connector lock -3- out, then disconnect the connector
from the seat belt tensioner igniter.
Installing
Install in reverse order of removal and note the following:
• If parts of the seat belt system are removed due to an accident,
replace the belt system bolts.
• Make sure the connectors are pushed in all the way and that
they engage audibly.
• Equipped on some models: after replacing the Left Front Seat
Belt Tensioner Control Module -J854- /Right Front Seat Belt
Tensioner Control Module -J855- , the control module must be
adapted using the Vehicle Diagnostic Tester.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1. Seat Belts 83
Audi A8 2018 ➤
Body Interior - Edition 10.2018
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Installing
– Insert the automatic belt retractor with the anti-twist mecha‐
nism -1- in the mount -arrow- and tighten the bolt.
Further installation is performed in reverse order of removal, while
noting the following:
• If parts of the seat belt system are removed due to an accident,
replace the belt system bolts.
• Make sure the connectors are pushed in all the way and that
they engage audibly.
• Equipped on some models: after replacing the Left Rear Seat
Belt Tensioner Control Module -J1097- /Right Rear Seat Belt
Tensioner Control Module -J1098- , the control module must
be adapted using the Vehicle Diagnostic Tester.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
Installation instructions: for example tightening specifications,
permitted unless re‐
authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
placing components. Refer to with respect to the correctness of information in this document. Copyright by AUDI AG.
⇒ “1.3 Overview - Outer Rear Three-Point Seat Belt”, page 75 .
Installing
– Insert the automatic belt retractor with the anti-twist mecha‐
nism -1- in the mount -2- -arrow- and tighten the bolt.
Further installation is performed in reverse order of removal, while
noting the following:
• If parts of the seat belt system are removed due to an accident,
replace the belt system bolts.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.4 Overview - Rear Center Three-Point Seat Belt”, page 77 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Installing
Removing
– Remove the B-pillar trim panels and move it to the side with
the seat belt webbing. Refer to
⇒ “6.11 B-Pillar Trim Panel, Removing and Installing”,
page 229 .
– Move the front seat all the way forward and up.
– Remove the nut -arrow A-.
– Unclip the wire -arrow B- on the air duct.
– Remove the air duct -1- from the B-pillar.
– Push the carpet slightly to the side and remove the air duct
upward -arrow C-.
1. Seat Belts 85
Audi A8 2018 ➤
Body Interior - Edition 10.2018
– Remove the nuts -arrows- and remove the seat belt guide
-1-.
Installing
Install in reverse order of removal.
Installation instructions: for example, tightening specifications,
replacing body parts. Refer to
⇒ “1.2 Overview - Front Three-Point Seat Belt”, page 73 and ⇒
Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air Rout‐
ing; Overview - Passenger Compartment Air Routing and Air
Distribution .
with respect to the correctness of information in this document. Copyright by AUDI AG.
Special tools and workshop equipment required
♦ Scraper no. 1 from the Scraper Set - VAS6845-
Removing
– Position the single seat in the front, lowest position.
– Move the rear headrests into the lowest position.
Outer seat belt guide:
– Unclip the seat belt guide -1- carefully from the rear shelf
-arrow- using the Scraper from the - VAS6845- .
– Disengage the remaining frame.
– Thread the seat belt webbing out and remove the seat belt
guide.
Removing
– Move the front seat all the way forward and up.
– Unclip the seat belt outlet trim -1- from the side sill side seat
side trim -arrow- by hand or using the scraper from the -
VAS6845- .
NOTICE
Risk of damaging the spring on the belt end fitting due to im‐
proper handling.
– Move the spring just far enough until it is possible to release
the tab on the spring.
– Push the belt end fitting -1- downward -arrow- and disengage
from the pin -3-.
– Guide out the belt end fitting upward through the seat belt
guide under the seat side trim.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.2 Overview - Front Three-Point Seat Belt”, page 73 .
1. Seat Belts 87
Audi A8 2018 ➤
Body Interior - Edition 10.2018
– Open the cover -2- for the belt end fitting -1- with a flat-head
screwdriver on the catch -arrow-, open and push to the side.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Push together the catches on the clamp with a plies
-A arrows-.
– At the same time push the anchoring pins -2- together with the
clamp -3- to release in the direction of -arrow B-.
– Disengage the anchoring pins from the clamp in the belt end
fitting -1-.
Installing
Install in reverse order of removal and note the following:
– Belt end fitting with seat belt tensioner: engage the anchoring
bolts -2- in the clamp -3- and push in the direction of
-arrow A-, until the catches -B arrows- engage.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.3.2 Overview - Rear Outer Three-Point Seat Belt, Single
Seats”, page 76 .
– Switch off the ignition and place the ignition key outside of the
vehicle and wait 10 seconds before working on the airbag sys‐
tem.
– Move the front seats all the way forward.
– Remove the single seat. Refer to ⇒ Seats; Rep. Gr. 72 ; Rear
Seats; Bench Seat / Single Seats, Removing and Installing .
– Open the cover -2- for the belt end fitting -1- with a flat-head
screwdriver on the catch -arrow-, open and push to the side.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Push the insulation mat for the rear panel to the side.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
1. Seat Belts 89
Audi A8 2018 ➤
Body Interior - Edition 10.2018
– Engage the anchoring bolts -2- in the clamp -3- and push in
the direction of -arrow A-, until the catches -B arrows- engage.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.3 Overview - Outer Rear Three-Point Seat Belt”, page 75 .
– First, insert the B-pillar trim panel -3- upward into the mount
on the roof.
• The mount -2- for the sliding piece of the B-pillar trim must
engage in the retaining pin -1- on the seat belt height adjuster
-arrow-.
– Seat belt height adjuster replacement part: after installing the
B-pillar trim panel, push the slider all the way up with force.
• This unlocks the seat belt height adjuster assembly anchor‐
age.
– When checking function, the following conditions must be ful‐
filled:
• The seat belt height adjuster must audibly engage at every
possible position (and in the highest position too).
• The seat belt height adjustment button must return to the up‐
per position by itself after being pressed.
• The seat belt relay must swing into the vertical position or to‐
wards the carrier by itself after tightening the screw.
If any of the listed conditions are not met, then the belt height
adjuster assembly must be checked. Replace the belt height ad‐
juster if necessary.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.2 Overview - Front Three-Point Seat Belt”, page 73 .
1. Seat Belts 91
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
Single seats: permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– If installed, disconnect and free up the seat belt switch con‐
nector -arrow- and free up the wire.
– Remove the screw -2-.
– Remove the seat belt latch -1-.
Installing
Install in reverse order of removal and note the following:
– Position the seat belt latch so that the anti-twist mechanism
engages in the cut-out.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.6 Overview - Rear Seat Belt Latch”, page 79 .
Bench Seat:
– If installed, free up and disconnect the connectors -arrows- for
the seat belt switch.
– Remove the nut -1-.
– Remove the right seat belt latch -2- with the center seat belt
latch -3-.
If necessary, separate the seat belt latches from each other:
CAUTION
Risk of injury due to flying metal shavings.
Irritation and injury to skin and eyes possible.
– Wear protective eyewear.
– Wear safety gloves.
1. Seat Belts 93
Audi A8 2018 ➤
Body Interior - Edition 10.2018
1 - Pop Rivets
2 - Child Seat Anchor
❑ Removing and Instal‐
ling. Refer to
⇒ “2.2 Rear Child Seat
Anchor, Removing and
Installing”, page 94 .
3 - Rear Shelf
❑ Removing and Instal‐
ling. Refer to
⇒ “6.15 Rear Shelf, Re‐
moving and Installing”,
page 235 .
4 - Cap
❑ Removing and Instal‐
ling. Refer to
⇒ “2.2 Rear Child Seat
Anchor, Removing and
Installing”, page 94 .
❑ Clipped in the rear shelf
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Cap, Removing
– Move the rear headrests into the lowest position.
– Unclip the cap -1- for the child seat anchor from the rear shelf
-arrow- using a scraper from the -VAS6845- .
Child Seat Anchor, Removing
– Remove the rear shelf front section. Refer to
⇒ “6.15 Rear Shelf, Removing and Installing”, page 235 .
– Remove the upper luggage compartment trim panel. Refer to
⇒ “7.9 Upper Luggage Compartment Trim Panel, Removing
and Installing”, page 253 .
CAUTION
Risk of injury due to flying metal shavings.
Irritation and injury to skin and eyes possible.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
– Wear protective eyewear. with respect to the correctness of information in this document. Copyright by AUDI AG.
– Drill out the pop rivets -arrows- from below (luggage compart‐
ment side).
– Push the insulation mat to the side and remove the child seat
anchor -1-.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Rear Child Seat Anchors”, page 94 .
3 Airbag System
⇒ “3.1 Component Location Overview - Airbag System”,
page 96
3. Airbag System 97
Audi A8 2018 ➤
Body Interior - Edition 10.2018
❑ Replace the Front Roof Module - WX3- . Refer to ⇒ Electrical Equipment; Rep. Gr. 96 ; Controls, Front
Interior Lamp/Reading Lamp, Removing and Installing .
22 - Front Passenger Airbag Deactivation Key Switch - E224-
❑ Not for North American Market.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Center Tunnel
2 - Connector
3 - Airbag Control Module -
J234-
❑ Removing and Instal‐
ling. Refer to
⇒ “4.2 Airbag Control
Module J234 , Remov‐
ing and Installing”, page
99 .
❑ The control module is
grounded via the hous‐
ing with the body.
4 - Ground Wire
5 - Nut
❑ Quantity: 4
❑ The thread must be
paint and contaminant
free, nut and ground
pins serve as ground
connection for the con‐
trol module.
❑ 9 Nm
6 - Connector
7 - Threaded Pins
❑ Quantity: Protected
4 by copyright. Copying for private or commercial purposes, in part or in whole, is not
❑ The threadpermitted
must unless
be authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
paint and contaminant
with respect to the correctness of information in this document. Copyright by AUDI AG.
free, nut and ground
pins serve as ground
connection for the con‐
trol module.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Remove the nuts -arrows- and remove the ground wire -3-.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Remove the airbag control module -2- from the threaded pins.
– Disconnect the connectors -1 and 4- by releasing the connec‐
tor safety catch and opening the securing clip on the connec‐
tor.
Installing
Install in reverse order of removal and note the following:
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
• Make sure the connectors are pushed in all the way and that
they engage audibly.
WARNING
Risk of airbag deployment after improper repair when connect‐
ing the battery.
There is a risk of injury.
– There must not be anyone in the vehicle interior when con‐
necting the battery.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
– Connect
permitted the battery
unless authorised ground
by AUDI AG. AUDI AG cable with
does not the ignition
guarantee switched
or accept any liability
with on. Refer
respect to ⇒ Electrical
to the correctness Equipment;
of information Rep.
in this document. Gr.by27
Copyright AUDI; Battery;
AG.
Battery, Disconnecting and Connecting .
WARNING
Risk of airbag deployment after improper repair when switching
on the ignition.
There is a risk of injury.
– Switching on the ignition (key/button) after assembly may
only be done when the driver seat is positioned all the way
back.
CAUTION
There is a risk of malfunction when the control module is not
activated correctly.
– Always adhere to the following procedure.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
⇒ Wiring diagrams,
Troubleshooting &
Component locations.
5 - Line
❑ Allocation. Refer to
⇒ Wiring diagrams,
Troubleshooting &
Component locations.
❑ Tightening specifica‐
tion. Refer to ⇒ Electri‐
cal Equipment; Rep. Gr.
97 ; Relay Panel, Fuse
Panel, E-Boxes .
6 - Nut
❑ Tightening specifica‐
tion. Refer to ⇒ Electri‐
cal Equipment; Rep. Gr. 97 ; Relay Panel, Fuse Panel, E-Boxes .
7 - Line
❑ Allocation. Refer to ⇒ Wiring diagrams, Troubleshooting & Component locations.
8 - Bolt
❑ Tightening specification. Refer to ⇒ Electrical Equipment; Rep. Gr. 97 ; Relay Panel, Fuse Panel, E-
Boxes .
9 - Line
❑ Allocation. Refer to ⇒ Wiring diagrams, Troubleshooting & Component locations.
❑ Tightening specification. Refer to ⇒ Electrical Equipment; Rep. Gr. 97 ; Relay Panel, Fuse Panel, E-
Boxes .
10 - Nut
❑ Tightening specification. Refer to ⇒ Electrical Equipment; Rep. Gr. 97 ; Relay Panel, Fuse Panel, E-
Boxes .
11 - Line
❑ Allocation. Refer to ⇒ Wiring diagrams, Troubleshooting & Component locations.
12 - Battery Interrupt Igniter - N253-
❑ Removing and Installing. Refer to ⇒ “5.2 Battery Interrupt Igniter, Removing and Installing”, page 104 .
13 - Nut
❑ Replace after removing.
❑ Quantity: 2
❑ 15 Nm
14 - Connector
❑ For the Battery Interrupt Igniter - N253-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Removing
– Pay attention to the safety precautions when working with py‐
rotechnic components. Refer to
⇒ “1 Safety Precautions”, page 1 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
– If »short circuit
permittedtounless
positive« isbya AUDI
authorised DTC AG.memory
AUDI AG does entry, discon‐
not guarantee or accept any liability
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Move the steering wheel as far to the rear and down as pos‐
sible. Use the full steering column adjustment range for this.
– Move the steering wheel out of the straight-ahead position by
turning it clockwise 90°, so that the opening on the rear side
of the steering wheel faces directly upward (approximately 12
o'clock position).
TIP:
To prevent damage to the wires do not use a flat-head screw‐
driver.
– Guide a Phillips head screwdriver -1- or Torx screwdriver T15
(approximately 80 mm long) in the opening until it stops.
– Release the locking bracket for the airbag by pulling the Torx
screwdriver upward forcefully -arrow-.
NOTICE
There is a risk of damaging the airbag unit if force is used.
– Never remove the airbag unit by pulling forcefully.
– Bring the steering wheel back into the center (wheels are
straight).
– Remove the airbag -1- from the steering wheel slightly.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Store the airbag with the cushion facing upward.
Installing
Install in reverse order of removal and note the following:
• Make sure the connectors are pushed in all the way and that
they engage audibly.
• Make sure the wires are not pinched.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
– Connectpermitted
the connector -1- to
unless authorised the AG.
by AUDI airbag igniter
AUDI AG -arrow
does not A-.or accept any liability
guarantee
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Press in the connector to secure it in the pockets on the steer‐
ing wheel.
– Position the driver side airbag in the steering wheel and press
on until it audibly engages.
– Check and erase the airbag control module DTC memory be‐
cause faults can be stored from when the connectors are
disconnected. Use the Vehicle Diagnostic Tester ⇒ Vehicle
diagnostic tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.1 Overview - Driver Side Airbag”, page 106 .
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Release the connector lock -2- for the connector -1- with a
small flat-head screwdriver -arrow-.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
1 - Connector
❑ For the Front Passenger
Airbag Igniter 2 - N132-
2 - Connector
❑ For Front Passenger
Airbag Igniter 1 - N131-
3 - Front Passenger Airbag
Unit - NX3-
❑ Removing and Instal‐
ling. Refer to
⇒ “7.2 Front Passenger
Airbag Unit with Igniter,
Removing and Instal‐
ling”, page 110 .
4 - Screws
❑ Replace after removing.
❑ 8 Nm
5 - Instrument Panel
❑ Replace the instrument
panel after an airbag
has deployed. Refer to
⇒ “4.6 Instrument Panel,
Removing and Instal‐
ling”, page 198 .
6 - Screws
❑ Replace after removing.
❑ 8 Nm
7 - Connector
❑ For the Front Passenger
Airbag Release Valve
Igniter - N491-
❑ Replace after the airbag
has deployed. Refer to
⇒ Electrical System General Information; Rep. Gr. 97 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle
Protected and wait
by copyright. 10 for
Copying seconds.
private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Remove the glove compartment. Refer to
⇒ “1.10 Glove Compartment, Removing and Installing”,
page 26 .
– Remove the mount for the Information Electronics Control
Module 1 - J794- and let it hang on the connected wires. Refer
to ⇒ Communication; Rep. Gr. 91 ; Infotainment System;
Component Location Overview - Infotainment System .
– Remove the instrument panel vent on the front passenger
side. Refer to
⇒ “4.9 Center Vent, Removing and Installing”, page 203 .
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Store the airbag with the cushion facing upward.
Installing
Install in reverse order of removal and note the following:
• Replace the connector for the Front Passenger Airbag Re‐
lease Valve Igniter - N491- after an airbag has deployed. Refer
to ⇒ Electrical Equipment; Rep. Gr. 97 ; Connectors; Wiring
Harnesses and Connectors, Repairing .
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester ⇒ Vehicle di‐
agnostic tester must always be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
nector disengages.
– Disconnect the connector -2-.
– Release the springs -3 and 5- and push the Front Passenger
Airbag Deactivation Key Switch - E224- -item 4- out of the key
switch housing.
Installing
Install in reverse order of removal and note the following:
• Make sure the connectors are pushed in all the way and that
they engage audibly.
• Make sure the wires are not pinched.
• Make sure the Front Passenger Airbag Deactivation Key
Switch - E224- engages audibly into the housing.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to ⇒ Vehicle diagnostic tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.4 Overview - Glove Compartment”, page 21 .
8 Thorax Airbags
⇒ “8.1 Overview - Front Thorax Airbag”, page 114
⇒ “8.2 Overview - Rear Thorax Airbag”, page 116
⇒ “8.3 Overview - Front Center Airbag”, page 117
⇒ “8.4 Overview - Rear Center Airbag”, page 118
⇒ “8.5 Front Thorax Airbag with Igniter, Removing and Installing”,
page 118
⇒ “8.6 Rear Thorax Airbag with Igniter, Removing and Installing”,
page 120
⇒ “8.7 Front Center Airbag with Igniter, Removing and Installing”,
page 121
⇒ “8.8 Rear Center Airbag with Igniter, Removing and Installing”,
page 123
⇒ “8.9 Front Thorax Airbag Wire, Removing and Installing”, page
125
⇒ “8.10 Rear Thorax Airbag Wire, Removing and Installing”, page
127
⇒ “8.11 Front Center Airbag Wire, Removing and Installing”, page
129
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Backrest Frame
2 - Front Thorax Airbag
❑ with
♦ Driver Thorax Airbag Igniter
- N199-
♦ Front Passenger Thorax
Airbag Igniter - N200-
❑ Removing and Instal‐
ling. Refer to
⇒ “8.5 Front Thorax Air‐
bag with Igniter, Remov‐
ing and Installing”, page
118 .
3 - Wire
❑ From Driver Thorax Air‐
bag Igniter - N199- /
Front Passenger Thor‐
ax Airbag Igniter - N200-
directly to the connector
station
❑ Removing and Instal‐
ling. Refer to
⇒ “8.9 Front Thorax Air‐
bag Wire, Removing
and Installing”,
page 125 .
4 - Bolt
❑ Replace after removing.
❑ Clean the threaded hole
for the bolt with a thread
tap, for example
❑ Install with locking com‐
pound. Refer to the
Parts Catalog for the
locking compound.
❑ 10 Nm
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Backrest Frame
2 - Rear Thorax Airbag
❑ with
♦ Driver Side Rear Thorax
Airbag Igniter - N201-
♦ Passenger Side Rear Thor‐
ax Airbag Igniter - N202-
❑ Removing and Instal‐
ling. Refer to
⇒ “8.6 Rear Thorax Air‐
bag with Igniter, Remov‐
ing and Installing”, page
120 . Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
3 - Bolt with respect to the correctness of information in this document. Copyright by AUDI AG.
❑ Quantity: 2
❑ Replace after removing.
❑ Clean the threaded hole
for the bolt with a thread
tap, for example
❑ Install with locking com‐
pound. Refer to the
Parts Catalog for the
locking compound.
❑ 6 Nm
4 - Connector
❑ For
♦ Driver Side Rear Thorax
Airbag Igniter - N201-
♦ Passenger Side Rear Thor‐
ax Airbag Igniter - N202-
1 - Backrest Frame
2 - Connector
❑ For Driver Side Front
Center Airbag Igniter for
Occupant Contact Pro‐
tection - N737-
3 - Driver Side Front Center
Airbag Igniter for Occupant
Contact Protection - N737-
❑ Removing and Instal‐
ling. Refer to
⇒ “8.7 Front Center Air‐
bag with Igniter, Remov‐
ing and Installing”, page
121 .
4 - Bolt
❑ Replace after removing.
❑ Clean the threaded hole
for the bolt with a thread
tap, for example
❑ Install with locking com‐
pound. Refer to the
Parts Catalog for the
locking compound.
❑ 8 Nm
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
3 - Bolt
❑ Replace after removing.
❑ Clean the threaded hole
for the bolt with a thread
tap, for example
❑ Install with locking com‐
pound. Refer to the
Parts Catalog for the
locking compound.
❑ 5 Nm
4 - Connector
❑ For Driver Side Front
Center Airbag Igniter for
Occupant Contact Pro‐
tection - N738-
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
– If the airbag indicator lamp does not turn on orunless
permitted blink, or there
authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
is no DTC memory entry with »short circuit to positive«:
with respect to the correctness of information in this document. Copyright by AUDI AG.
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
– Disengage the cover (side sill side) in the area of the thorax
airbag.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Removing
– Pay attention to the safety precautions when working with py‐
rotechnic components. Refer to
⇒ “1 Safety Precautions”, page 1 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Push the tab -2- from the center airbag -1- in the opening on
the bracket -3- under the rear shelf.
Further installation is performed in reverse order of removal, while
noting the following:
• Pay attention that the wire -4- is not pinched.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to ⇒ Vehicle diagnostic tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “8.4 Overview - Rear Center Airbag”, page 118 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components
Protected by copyright. canor deploy
Copying for private commercialunintentionally.
purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
There is a risk
with respect to theof injury. of information in this document. Copyright by AUDI AG.
correctness
– Discharge static electricity by briefly touching the door strik‐
er.
Removing
– Pay attention to the safety precautions when working with py‐
rotechnic components. Refer to
⇒ “1 Safety Precautions”, page 1 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag
Protected indicator
by copyright. lamp
Copying turns
for private on or blinks.
or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
– If the airbagwith
indicator
respect to lamp turns of
the correctness oninformation
or blinks, the
in this DTC Copyright
document. mem‐ by AUDI AG.
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Igniter - N251-
with respect to the correctness of information in this document. Copyright by AUDI AG.
Removing
– Pay attention to the safety precautions when working with py‐
rotechnic components. Refer to
⇒ “1 Safety Precautions”, page 1 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
– Unclip the head curtain airbag clips from the body using -
VAS211 001- .
– Do this by guiding the plier tips into the openings, press the
clip catches -1- for the head curtain airbag together and re‐
move the clip.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Installing
– Hook the rear head curtain airbag in the mount on the body
-arrow A-.
– Engage the front head curtain airbag in the mount -arrow B-
and tighten.
Further installation is performed in reverse order of removal, while
noting the following:
• After the airbag has deployed the corresponding Right Rear
Midrange Speaker 2 - R340- and Left Rear Midrange Speaker
2 - R341- must be replaced. Refer to ⇒ Communication; Rep.
Gr. 91 ; Sound System; Component Location Overview -
Sound System .
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
10 Knee Airbags
⇒ “10.1 Overview - Knee Airbag”, page 134
⇒ “10.2 Knee Airbag with Igniter, Removing and Installing”, page
135
3 - Bracket
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
❑ For the knee airbag
4 - Bolt
❑ Quantity: 2
❑ 3 Nm
5 - Bracket
❑ For the knee airbag
6 - Bolt
❑ Quantity: 2
❑ 3 Nm
7 - Nut
❑ Quantity: 2
❑ Replace after removing.
❑ 8 Nm
8 - Connector
❑ For Driver Knee Airbag
Igniter - N295-
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Pull out the connector lock -2- -arrow- and disconnect the con‐
nector -1-.
– Remove the bolts -3 and 4-.
– Disengage and remove the knee airbag
Protected -5- with
by copyright. the for
Copying bracket
private or commercial purposes, in part or in whole, is not
on the crossmember. permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Bracket, Removing:
– Place the knee airbag on a soft surface with the collision cush‐
ion facing upward.
– Remove the nuts -arrows-.
– Remove the bracket -1 and 2-.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Store the airbag with the cushion facing upward.
Installing
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
Install in reverse order ofpermitted
removal and
unless notebythe
authorised following:
AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
NOTICE
There is a risk of damaging the surface of the knee airbag from
mechanical stress.
– After completing a procedure, perform a visual inspection to
make sure that the surface of the knee airbag is not dam‐
aged.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided FaultProtected
Finding by copyright. Copying for private or commercial purposes, in part or in whole, is not
instructions on the Vehicle Diagnostic Tester mustpermitted
always unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
be followed. with respect to the correctness of information in this document. Copyright by AUDI AG.
– Lower the knee airbag -1- slightly and disengage at the inside
of the glove compartment -A arrows-.
– Tilt the knee airbag downward, disengage at the glove com‐
partment -B arrows- and remove.
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Store the airbag with the cushion facing upward.
Installing
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
NOTICE
There is a risk of damaging the surface of the knee airbag from
mechanical stress.
– After completing a procedure, perform a visual inspection to
make sure that the surface of the knee airbag is not dam‐
aged.
damaged or deformed
❑ The tabs must audibly
engage
4 - Nut
❑ 9 Nm
❑ 9 Nm
12 - Driver Front Airbag Crash Sensor - G283-
❑ Component location: left side of lock carrier
❑ Removing and Installing. Refer to
⇒ “11.2 Driver Front Airbag Crash Sensor G283 , Removing and Installing”, page 141 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
– Remove the bolt -2- and the front airbag crash sensor -3- from
the lock carrier.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– To do this pull out the connector lock -2-, push down -arrow-,
and disconnect the connector -1- on the crash sensor.
Installing
Install in reverse order of removal and note the following:
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Attach the connector -1- to the crash sensor until it clicks into
place -arrow-.
– Push in the connector lock -2- to secure the connector.
• Make sure the wires are not pinched.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to Vehicle Diagnostic Tester.
Installation instructions: for example tightening specifications,
Protected re‐ for private or commercial purposes, in part or in whole, is not
by copyright. Copying
placing components. Refer to permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
⇒ “11.1 Component Location Overview - Airbagwith Crash
respect Sensors”,
to the correctness of information in this document. Copyright by AUDI AG.
page 140 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Pull out the connector lock -2- and push down -arrow-, dis‐
connect the connector -1- on the crash sensor.
CAUTION
Risk of malfunction of the crash sensor (pressure) do to leaks.
– Make sure that the door does not have leaks.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Attach the connector -1- to the crash sensor until it clicks into
place -arrow-.
– Push in the connector lock -2- to secure the connector.
• Make sure the wires are not pinched.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to Vehicle Diagnostic Tester.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Installation instructions: for example tightening specifications,
withre‐
respect to the correctness of information in this document. Copyright by AUDI AG.
placing components. Refer to
⇒ “11.1 Component Location Overview - Airbag Crash Sensors”,
page 140 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
– To do this pull out the connector lock -2-, push down -arrow-,
and disconnect the connector -1- on the crash sensor.
Installing
Install in reverse order of removal and note the following:
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Attach the connector -1- to the crash sensor until it clicks into
place -arrow-.
– Push in the connector lock -2- to secure the connector.
• Make sure the wires are not pinched.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to Vehicle Diagnostic Tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “11.1 Component Location Overview - Airbag Crash Sensors”,
page 140 .
WARNING
Risk of airbag deployment.
There is a risk of injury.
– Check if the airbag indicator lamp turns on or blinks.
– If the airbag indicator lamp turns on or blinks, the DTC mem‐
ory must be read.
– If »short circuit to positive« is a DTC memory entry, discon‐
nect the battery. Refer to ⇒ Electrical Equipment; Rep. Gr.
27 ; Battery; Battery, Disconnecting and Connecting .
– If there is a DTC memory entry, the Guided Fault Finding
instructions on the Vehicle Diagnostic Tester must always
be followed.
– If the airbag indicator lamp does not turn on or blink, or there
is no DTC memory entry with »short circuit to positive«:
switch off the ignition, keep the ignition key outside of the
vehicle and wait 10 seconds.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Remove the bolt -1- and remove the crash sensor -2- from the
body.
– Disconnect the connector -3- by pressing the connector lock
down.
Installing
Install in reverse order of removal
Protected by copyright. and note
Copying the or
for private following:
commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
CAUTION with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Wiring Harness
❑ Seat position sensor/
passenger occupant de‐
tection sensor/seat belt
switch
❑ Available only together
with -item 3-
❑ Clip into the seat frame
❑ Black connector, con‐
nector station in the ve‐
hicle floor under the seat
❑ Removing and Instal‐
ling. Refer to
⇒ “12.2 Seat Position
Sensor, Removing and
Installing”, page 148 .
2 - Passenger Seat Occupant
Detection Sensor - G128-
❑ Only the front passen‐
ger side
❑ Removing and Instal‐
ling. Refer to
⇒ “13.1 Passenger Seat
Occupant Detection
Sensor G128 , Remov‐
ing and Installing”, page
150 .
❑ Push into the seat pan
until they click into place
3 - Seat Position Sensor
♦ Driver Seat Position Sensor
- G553-
♦ Front Passenger Seat Po‐
sition Sensor - G554- Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
❑ Only available together with respect to the correctness of information in this document. Copyright by AUDI AG.
with -item 1-
❑ Shown on the front passenger side
❑ Removing and Installing. Refer to ⇒ “12.2 Seat Position Sensor, Removing and Installing”, page 148 .
❑ Checking. Refer to Vehicle Diagnostic Tester.
4 - Bolt
❑ 1.2 Nm
– Free up and disconnect the connector -1- to the seat belt latch.
– Front passenger seat: disconnect the connector -2- on the
Passenger Seat Occupant Detection Sensor - G128- .
– Remove the cable ties or wire bracket -arrows- for the wire on
the seat pan lower frame.
– Remove the seat position sensor with the wires.
Installing
Install in reverse order of removal.
• Check the seat position sensor with the Vehicle Diagnostic
Tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “12.1 Overview - Seat Position Sensor”, page 148 .
Removing
– Move the front passenger all the way back to the highest po‐
sition.
– Disconnect the connector -2- for the passenger occupant de‐
tection sensor.
– Unclip the mount -1- from the seat pan -arrows- and remove
the passenger occupant detection sensor -3-.
Installing
Install in reverse order of removal and note the following:
• Make sure the connectors are pushed in all the way and that
they engage audibly.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to Vehicle Diagnostic Tester.
6 - Bolt
❑ Tightening specification -item 4- ⇒ Item 4 (page 148)
7 - Wiring Harness
❑ Seat position sensor/passenger occupant detection sensor/seat belt switch
❑ Available only with -item 5-
❑ Clip into the seat frame
❑ Black connector, connector station in the vehicle floor under the seat
❑ Removing and Installing. Refer to ⇒ “12.2 Seat Position Sensor, Removing and Installing”, page 148 .
15 Active Headrest
⇒ “15.1 Front Passenger and Driver Active Head Restraint Ignit‐
ers N419 / N420 , Replacing after Deployment”, page 154
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Insert the -VAS211 001- in the holes -1- and -4- from the lock‐
ing mechanism -2-
– Turn the locking mechanism approximately 45° counter-clock‐
wise -arrow- and remove together with the ignition for the
active headrest -3-.
Installing
– Press the release -2- in the direction of the -arrow B- until it
engages if necessary use a tool.
• The help of a second technician is necessary for the following
step.
– Have a second technician push the headrest guide with the
support -1- without tilting all the way in the headrest guide
-3- and hold it -A arrows-.
CAUTION
Pyrotechnical components can deploy unintentionally.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
There is a risk of injury. with respect to the correctness of information in this document. Copyright by AUDI AG.
– Bring the rear cover -2- into the installation position and push
on the headrest until it engages audibly -arrows-.
– Retrieve the airbag control module DTC memory and delete it
using the Vehicle Diagnostic Tester .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
16 Pedestrian Protection
⇒ “16.1 Overview - Pedestrian Protection”, page 157
⇒ “16.2 Pedestrian Protection Crash Sensor G570 / G571 , Re‐
moving and Installing”, page 158
⇒ “16.3 Pressure Hose Sensor for Front Pedestrian Protection
G579 , Removing and Installing”, page 160
⇒ “16.4 Pedestrian Protection Center Crash Sensor G693 , Re‐
moving and Installing”, page 161
⇒ “16.5 Triggered Pedestrian Protection, Resetting”, page 162
⇒ “16.6 Pedestrian Protection Trigger 1 G598 / Pedestrian Pro‐
tection Trigger 2 G599 , Removing and Installing”, page 162
– Switch off the ignition and place the ignition key outside of the
vehicle and wait 10 seconds before working on the airbag sys‐
tem.
– Remove the front bumper cover. Refer to ⇒ Body Exterior;
Rep. Gr. 63 ; Front Bumper; Bumper Cover, Removing and
Installing .
– Remove the bolt -2- and remove the crash sensor for the pe‐
destrian protection -3- from the bumper.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– To do this pull out the connector lock -2-, push down -arrow-,
and disconnect the connector -1- on the crash sensor.
Installing
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
NOTICE
Risk of damaging the pressure hose due to improper handling.
– Do not kink or turn the pressure hose.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Attach the connector -1- to the crash sensor until it clicks into
place -arrow-.
– Push in the connector lock -2- to secure the connector.
• Make sure the wires are not pinched.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to Vehicle Diagnostic Tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “16.1 Overview - Pedestrian Protection”, page 157 .
ling permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Removing
– Pay attention to the safety precautions when working with py‐
rotechnic components. Refer to
⇒ “1 Safety Precautions”, page 1 .
– Switch off the ignition and place the ignition key outside of the
vehicle and wait 10 seconds before working on the airbag sys‐
tem.
– Remove the lock carrier cover. Refer to ⇒ Body Exterior; Rep.
Gr. 63 ; Front Bumper .
– Remove the bolt -1- and crash sensor -2- from the radiator
grille.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– To do this pull out the connector lock -2-, push down -arrow-,
and disconnect the connector -1- on the crash sensor.
Installing
Install in reverse order of removal and note the following:
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
– Attach the connector -1- to the crash sensor until it clicks into
place -arrow-.
– Push in the connector lock -2- to secure the connector.
• Make sure the wires are not pinched.
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to Vehicle Diagnostic Tester.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “16.1 Overview - Pedestrian Protection”, page 157 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
17 Special Tools
Special tools and workshop equipment required
♦ Wedge Set - T10383-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
70 – Interior Trim
1 Trim Panels and Insulation
⇒ “1.1 Component Location Overview - Trim Panels and Insula‐
tion”, page 165
⇒ “2.1 Overviewwith
- Front
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
respect to the correctness of information in this document. Copyright by AUDI AG.
Door Trim Panel”,
page 166 .
3 - Instrument Panel
❑ Overview. Refer to
⇒ “4.1 Overview - Instru‐
ment Panel”,
page 190 .
4 - Crossmember
❑ For the instrument panel
❑ Overview. Refer to
⇒ “5.1 Overview - Instru‐
ment Panel Crossmem‐
ber”, page 212 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
⇒ “2.6.2 Front Passenger Side Pull Handle, Removing and Installing”, page 173 .
23 - Armrest Decorative Trim
❑ Front passenger side
❑ Equipped on some models
❑ Removing and Installing. Refer to
⇒ “2.7 Pull Handle/Armrest Decorative Trim, Removing and Installing”, page 174 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
Bass Speaker
permitted Trim,
unless authorised Removing
by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Pry up the bass speaker trim -1- along the door trim panel gap
-arrows-, at the same time the catches are released using the
-80-200- .
– Equipped on some models: disconnect the connector for the
ambient lighting.
– Remove the speaker trim from the door panel.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Front Door Trim Panel”, page 166 .
Removing
– Unclip the front decorative trim using the -3409- -A arrows-.
TIP:
So that the rear retainers on the decorative trim are not damaged,
the decorative trim must be held parallel to the door trim panel
and pushed toward the front.
– Unclip the rear decorative trim straight from the door trim panel
-arrow B- using the -3409- .
– Push the decorative trim toward the front and disengage from
the door trim panel and remove.
– Disconnect the connectors, if equipped.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Front Door Trim Panel”, page 166 .
– Using the -T10383- , unclip the door trim panel at the lower
rear section in a radius beginning at the door by inserting the
wedge near the clips between the door trim panel and the door
-arrow-.
– Unclip the remaining clips along the door trim panel from the
door.
– Pull the door trim panel -1- slightly off the door all the way
around -arrow A-.
• The clips must not be left inside the door.
– Push the door trim panel upward and disengage it from the
door at the window shaft -B arrows-.Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
NOTICE
Risk of damaging the operating cable by deforming it.
– Never sharply bend or kink the operating cable.
– Carefully unclip the release cable -4- from the interior door
mechanism -3- -arrow- at the same time the catches
-2 and 5- are loosened.
– Disengage the release cable nipple -1- from the interior door
mechanism.
Installing
Install in reverse order of removal and note the following:
– Position the door trim on the window recess and press it down
firmly.
– Carefully position the door trim panel clips -2- all around the
door -1- and press the door trim panel onto the door until it
engages audibly on the mounting points -arrows-.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Front Door Trim Panel”, page 166 .
– Disconnect the connector -1-. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
– Remove the screw -3-. with respect to the correctness of information in this document. Copyright by AUDI AG.
– Carefully unclip the switch mount -4- from the pull handle -2-
using the -T10383/1- , at the same time the catches -arrows-
are released.
– Remove the switch mount.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Front Door Trim Panel”, page 166 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Installing
– Insert window frame trim panel -1- at the top back of the win‐
dow guide -2- -arrow-.
– Install window frame trim panel -2- along the entire length of
the window guide.
– Remove the protective film from the adhesive pads on the new
part.
– Push the trim panel firmly against the door in the adhesive pad
area -1, 3-
Further installation is the reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “2.1 Overview - Front Door Trim Panel”, page 166 .
– Slightly lift the cover -1- for the front storage compartment
-arrow A- and remove it from the rear axle -arrow B-.
– Guide out the wire for the heating element and remove the
cover.
Installing
Install in reverse order of removal.
Information for installation: for example, tightening specifications,
replacing body parts. Refer to
⇒ “2.1 Overview - Front Door Trim Panel”, page 166 and
⇒ “3.1 Overview - Rear Door Trim Panel”, page 178 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
5 - Clip
❑ For door trim panel
❑ Quantity: 7
❑ Insert in the trim panel
6 - Insulation Mat
7 - Window Frame Trim Panel
❑ Removing and Installing. Refer to
⇒ “3.9 Window Frame Trim Panel, Removing and Installing”, page 185 .
8 - Door Trim Panel Stopper
❑ 4.5 Nm
9 - Door Trim Panel
❑ Removing and Installing. Refer to ⇒ “3.5 Rear Door Trim Panel, Removing and Installing”, page 182 .
10 - Bolt
❑ For the interior door mechanism
❑ Quantity: 7
❑ 1.2 Nm
11 - Interior Door Mechanism
❑ Removing and Installing. Refer to
⇒ “3.8 Interior Door Mechanism, Removing and Installing”, page 184 .
12 - Decorative Trim
❑ Removing and Installing. Refer to ⇒ “3.4 Decorative Trim, Removing and Installing”, page 181 .
13 - Decorative Insert
14 - Midrange Speaker Trim
❑ Removing and Installing. Refer to
⇒ “3.3 Speaker Trim in Door Trim Panels, Removing and Installing”, page 180 .
15 - Bass Speaker Trim
❑ Removing and Installing. Refer to
⇒ “3.3 Speaker Trim in Door Trim Panels, Removing and Installing”, page 180 .
16 - Armrest Decorative Trim
❑ Equipped on some models
❑ Removing and Installing. Refer to
⇒ “3.7 Armrest Decorative Trim, Removing and Installing”, page 184 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Bolt
❑ Quantity: 2
❑ 3.3 Nm
2 - Push Rod
❑ Removing and Instal‐
ling. Refer to
⇒ “3.10.1 Door Window
Sun Shade, Removing
and Installing”,
page 186 .
3 - Bolt
❑ Quantity: 4
❑ 3.3 Nm
4 - Sun Shade
❑ Removing and Instal‐
ling. Refer to
⇒ “3.10.1 Door Window
Sun Shade, Removing
and Installing”,
page 186 .
5 - Bolt
❑ Quantity: 2
❑ 3.3 Nm
6 - Rear Side Shade Motor
♦ Driver Side Rear Side
Shade Motor - V692-
♦ Passenger Side Rear Side
Shade Motor - V693-
❑ Removing and Instal‐
ling. Refer to
⇒ “3.10.2 Driver and
Passenger Side Rear
Side Shade Motor
V692 / V693 , Removing and Installing”, page 188 .
– Using the -T10383- , unclip the door trim panel at the lower
rear section in a radius beginning from the door by inserting
the wedge between the door trim panel and the door near the
clips -arrow-.
– Unclip the remaining clips along the door trim panel from the
door.
– Pull the door trim panel -1- slightly off the door all the way
around -arrow A-.
• The clips must not be left inside the door.
– Push the door trim panel upward and disengage it from the
door at the window shaft -B arrows-.
NOTICE
Risk of damaging the operating cable by deforming it.
– Never sharply bend or kink the operating cable.
– Carefully unclip the release cable -4- from the interior door
mechanism -3- -arrow- at the same time the catches
-2 and 5- are loosened.
– Disengage the release cable nipple -1- from the interior door
mechanism.
Installing
Install in reverse order of removal and note the following.
– Position the door trim on the window recess and press it down
firmly.
– Carefully position the door trim panel clips -2- all around the
door -1- and press the door trim panel onto the door until it
engages audibly on the mounting points -arrows-.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.1 Overview - Rear Door Trim Panel”, page 178 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Installing
– Insert the window frame trim panel -2- in the upper front sec‐
tion of the window guide -1- -arrow-.
– Install window frame trim panel -2- along the entire length of
the window guide.
– Remove the protective film from the adhesive pads on the new
part.
– Push the trim panel firmly against the door in the adhesive pad
area -1, 3-
Further installation is the reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
⇒ “3.1 Overview - Rear Door Trim Panel”, page
permitted 178
unless .
authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Unclip the sun shade from the mount -2- upward from the push
rod -1- -arrow-.
– Turn the push rod -2- approximately 90° on it axis -arrow A-.
– Remove the push rod upward from the engine -1- for the sun
shade -arrow B- to do so leave the push rod turned approxi‐
mately 90° on its axis.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Installing
Install in reverse order of removal and note the following:
– Open the sun shade trim -1- and push the push rod -2- through
the hole -arrow A- in the mount in the sun shade motor
-arrow B-.
– Push the push rod downward and turn it slightly on its axis until
there is noticeable play.
– Pull on the push rod to make sure it is secure.
– Clip the sun shade in the push rod.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “3.2 Overview - Door Window Sun Shade”, page 180 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Turn the push rod -2- approximately 90° on it axis -arrow A-.
– Remove the push rod upward from the engine -1- for the sun
shade -arrow B- to do so leave the push rod turned approxi‐
mately 90° on its axis.
Installing
Install in reverse order of removal and note the following:
– Open the sun shade trim -1- and push the push rod -2- through
the hole -arrow A- in the mount in the sun shade motor
-arrow B-.
– Push the push rod downward and turn it slightly on its axis until
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
there is noticeable play. with respect to the correctness of information in this document. Copyright by AUDI AG.
4 Instrument Panel
⇒ “4.1 Overview - Instrument Panel”, page 190
⇒ “4.2 Instrument Panel Side Cover, Removing and Installing”,
page 194
⇒ “4.3 Speaker Trim, Removing and Installing”, page 195
⇒ “4.4 Instrument Panel Decorative Trim, Removing and Instal‐
ling”, page 196
⇒ “4.5 Instrument Panel Trim, Removing and Installing”,
page 197
⇒ “4.6 Instrument Panel, Removing and Installing”, page 198
⇒ “4.7 Instrument Panel/Windshield Projection (Head-Up Dis‐
play) Cover, Removing and Installing”, page 202
⇒ “4.8 Outer Instrument Panel Vent, Removing and Installing”,
page 203
⇒ “4.9 Center Vent, Removing and Installing”, page 203
⇒ “4.10 Instrument Panel Vent Decorative Trim, Removing and
Installing”, page 205
⇒ “4.11 Vent Adjustment Motors, Removing and Installing”, page
208
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Bolt
❑ Quantity: 2
❑ 1.5 Nm
2 - Bolt
❑ 3 Nm
3 - Instrument Panel Vent
Frame
❑ Driver side
❑ Removing and Instal‐
ling. Refer to
⇒ “4.10.1 Instrument
Panel Vent Decorative
Trim, Removing and In‐
stalling, Driver Side”,
page 205 .
4 - Instrument Panel Vent Dec‐
orative Trim
❑ Driver side
❑ Removing and Instal‐
ling. Refer to
⇒ “4.10.1 Instrument
Panel Vent Decorative
Trim, Removing and In‐
stalling, Driver Side”,
page 205 .
5 - Driver Side Instrument Pan‐
el Vent
❑ Removing and Instal‐
ling. Refer to
⇒ “4.8 Outer Instrument
Panel Vent, Removing
and Installing”,
page 203 .
6 - Bolt
❑ Quantity: 2 Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
❑ 1.5 Nm with respect to the correctness of information in this document. Copyright by AUDI AG.
placing components. with Refer toto the correctness of information in this document. Copyright by AUDI AG.
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
respect
⇒ “4.1 Overview - Instrument Panel”, page 190 .
NOTICE
There is a risk of damaging the speaker trim if handled incor‐
rectly.
– Carefully removing and installing the speaker trim.
– Move the steering wheel as far to the rear and down as pos‐
sible. Use the full steering column adjustment range for this.
– Remove the driver and front passenger side instrument panel
decorative trim. Refer to
⇒ “4.4 Instrument Panel Decorative Trim, Removing and In‐
stalling”, page 196 .
– Unclip the steering column trim panel gap cover -2- at the side
and top from the instrument panel trim -1- -arrows- using the
clip release lever from the Scraper Set -VAS6845- .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
NOTICE
There is a risk of destroying the windshield projection head up
display control module.
– Only remove labeled bolts on the control module.
– Never remove bolts for the housing upper section.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
CAUTION
Pyrotechnical components can deploy unintentionally.
There is a risk of injury.
– Discharge static electricity by briefly touching the door strik‐
er.
Removing
– Remove the instrument panel trim. Refer to
⇒ “4.5 Instrument Panel Trim, Removing and Installing”, page
197 .
– Remove the instrument cluster and push to the side with the
wires connected. Refer to ⇒ Electrical Equipment; Rep. Gr.
90 ; Instrument Cluster; Overview - Instrument Cluster .
– Loosen the Steering Column Electronics Control Module -
J527- the connectors remain connected. Refer to ⇒ Electrical
Equipment; Rep. Gr. 94 ; Steering Column Switch Module;
Steering Column Switch Module, Removing and Installing .
– Remove the Front Information Display Control Head - J685- .
Refer to ⇒ Communication; Rep. Gr. 91 ; Infotainment Sys‐
tem; Infotainment System Display, Removing and Installing .
– Remove the bolts -1, 3, 4 and 5-.
– Unclip the instrument panel vent -2- using the -3409-
-arrows-.
– Disengage the remaining retainers, carefully remove the in‐
strument panel vent and disconnect the connectors.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “4.1.2 Overview - Instrument Panel Vent”, page 193 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Removing
– Remove the instrument cluster. Refer to ⇒ Electrical Equip‐
ment; Rep. Gr. 90 ; Instrument Cluster; Overview - Instrument
Cluster .
– Remove the bolts -arrows-.
– Remove the adjustment motor -1- from the shaft -3-.
– Disconnect the connector -2-.
Installing
Install in reverse order of removal and note the following:
NOTICE
Risk of damaging the adjustment motor
Protected electronics
by copyright. Copying fordue
privatetoorin‐
commercial purposes, in part or in whole, is not
correct handling. permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Never turn the adjustment motor mount by hand.
NOTICE
Risk of damaging the adjustment motor electronics due to in‐
correct handling.
– Never turn the adjustment motor mount by hand.
NOTICE
Risk of damaging the adjustment motor electronics due to in‐
correct handling.
– Never turn the adjustment motor mount by hand.
1 - Bolt
❑ Quantity: 3
❑ Tightening specification
and sequence. Refer to
⇒Protected
page 213 .
by copyright. Copying for private or commercial purposes, in part or in whole, is not
2 - Nut with respect to the correctness of information in this document. Copyright by AUDI AG.
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
❑ Quantity: 2
❑ Replace after removing.
❑ Tightening specification
and sequence. Refer to
⇒ page 213 .
3 - Bolt
❑ The mounting threads
and contact surface
must be free of paint,
coating and corrosion.
The threaded connec‐
tion serves as the
ground connection.
❑ Tightening specification
and sequence. Refer to
⇒ page 213 .
4 - Threaded Pin
❑ Quantity: 2
❑ 20 Nm
5 - Foam Washer
❑ Quantity: 2
❑ Replace if damaged
6 - Lifter
❑ Quantity: 2
❑ Clipped in the cross‐
member
❑ Check the lifter adjusting nut for ease of movement
7 - Bolt
❑ Quantity: 2
❑ Tightening specification and sequence. Refer to ⇒ page 213 .
8 - Plug
❑ Quantity: 2
9 - Bolt
❑ Quantity: 2
❑ Tightening specification and sequence. Refer to ⇒ page 213 .
10 - Spacer
❑ Quantity: 2
❑ maximum 0.5 Nm
11 - Bracket
❑ For the windshield projection control module
❑ Must not be removed. If the bracket is removed, the instrument panel crossmember must be replaced.
Refer to ⇒ “5.2 Instrument Panel Crossmember, Removing and Installing”, page 213 .
12 - Bolt
❑ For the front heater and A/C unit
❑ Quantity: 5
❑ Tightening specification and sequence. Refer to ⇒ page 213 .
13 - Bolt
❑ Tightening specification and sequence. Refer to ⇒ page 213 .
14 - Crossmember
❑ For the instrument panel
❑ Removing and Installing. Refer to
⇒ “5.2 Instrument Panel Crossmember, Removing and Installing”, page 213 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Remove the bolt -1- and nut -2- for the instrument panel cross‐
member.
– Repeat the process on the opposite side.
– Unclip, disengage and free up the wires from the instrument
panel crossmember.
• Two technicians are needed to remove the instrument panel
crossmember.
– Disengage the instrument panel crossmember from the heater
and A/C unit and remove from the vehicle interior toward the
rear.
Installing
– Check all adjusting mechanisms -2- on the instrument panel
crossmember by allowing the adjusting nut -1- to rotate gently
-arrows-.
– Turn the adjusting nut all the way downward until the adjuster
engages in the transportation safeguard
– Carefully insert the instrument panel crossmember in the
body.
– Align the instrument panel crossmember according to the
marks applied to the A-pillar during removal.
– Tighten the nuts and bolts for the instrument panel crossmem‐
ber near the A-pillar on both the driver and front passenger
sides.
Further installation is performed in reverse order of removal, while
noting the following:
– Install the steering column. Refer to ⇒ Suspension, Wheels,
Steering; Rep. Gr. 48 ; Steering Column; Overview - Steering
Column .
– Mounting bracket for pedal assembly. Refer to ⇒ Brake Sys‐
tem; Rep. Gr. 46 ; Brake Pedal; Overview - Brake Pedal .
– Equipped on some models: install the Windshield Projection
Head Up Display Control Module - J898- . Refer to ⇒ Electrical
Equipment; Rep. Gr. 90 ; Instrument Cluster; Windshield Pro‐
jection Head Up Display Control Module, Removing and In‐
stalling .
Installation Position of Instrument Panel Crossmember, Checking
– Insert the instrument panel to test.
– Secure the instrument panel on the left and right side to the
instrument panel crossmember.
– Close the doors.
– Check whether the gap dimension between the instrument
panel and the left and right door is even.
– Check whether the height of instrument panel aligns with the
moldings in the door trim panels.
– If the adjustment is incorrect, note lateral and/or vertical devi‐
ation.
– Loosen the instrument panel Protected
crossmember threaded connec‐
by copyright. Copying for private or commercial purposes, in part or in whole, is not
tions.
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Tighten the bolt -1- and nut -2- for the instrument panel cross‐
member near the A-pillar on both the driver and front passen‐
ger sides.
– Install the windshield. Refer to ⇒ Body Exterior; Rep. Gr. 64 ;
Windshield; Windshield, Removing and Installing .
• If the instrument cluster indicates a fault in the airbag system
after assembly, the DTC memory must be checked, erased,
and then checked again. Refer to ⇒ Vehicle diagnostic tester.
Information for installation: for example, tightening specifications,
replacing body parts. Refer to
⇒ “5.1 Overview - Instrument Panel Crossmember”, page 212 and
⇒ Fig. ““Instrument panel crossmember to body - tightening spec‐
ifications and sequence”“ , page 213 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Rear Shelf
❑ Overview. Refer to
⇒ “6.8 Overview - Rear
Shelf”, page 225 .
2 - Rear Carpet
❑ Overview. Refer to
⇒ “6.7 Overview - Foot‐
rest and Carpet”,
page 224 .
3 - Front Carpet
❑ Overview. Refer to
⇒ “6.7 Overview - Foot‐
rest and Carpet”, Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
page 224 .
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Clip
❑ Quantity: 4
❑ Insert in the body
❑ Replace damaged or
deformed clips
2 - Sill Panel
❑ Removing and Instal‐
ling. Refer to
⇒ “6.9 Sill Panel, Re‐
moving and Installing”,
page 226 .
❑ Press on until it engages
audibly
❑ Stretch the inner door
seal lip over. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
3 - Clip with respect to the correctness of information in this document. Copyright by AUDI AG.
❑ Quantity: 2
❑ Insert in the sill panel
❑ Replace damaged or
deformed clips
1 - Clip
❑ Quantity: 3
❑ Insert in the trim panel
❑ Replace damaged or
deformed clips
2 - A-Pillar Lower Trim Panel
❑ Removing and Instal‐
ling. Refer to
⇒ “6.10.2 A-Pillar Lower
Trim Panel, Removing
and Installing”,
page 228 .
❑ Pushed forward in the
carpet
❑ Stretch the inner door
seal lip over.
3 - A-Pillar Gap Cover
❑ Removing and Instal‐
ling. Refer to
⇒ “6.10 A-Pillar Trim
Panel, Removing and
Installing”, page 226 .
❑ Clip into the A-pillar trim
panels
❑ Stretch the inner door
seal lip over.
4 - Clip
❑ Insert in the trim panel
❑ Remove the clips that
are still in the body
mounting points using
the Omega Clip Tool -
T40280- .
❑ Replace damaged or
deformed clips
5 - Clip
❑ With hooks
❑ Replace after removing the A-pillar trim panel
❑ Insert in the trim panel
6 - Retaining Pin
❑ 3.5 Nm
7 - A-Pillar Upper Trim Panel
❑ Allocation. Refer to the Parts Catalog.
❑ Removing and Installing. Refer to
⇒ “6.10.1 A-Pillar Upper Trim Panel, Removing and Installing”, page 226 .
❑ Press on until it engages audibly
❑ Stretch the inner door seal lip over.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
8 - Operating Lever Handle permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
9 - Bolt
❑ Driver side only
❑ 2 Nm
1 - Expanding Clip
❑ Remove using the Pliers
- T40172C-
2 - Speaker Trim
❑ Clip in the B-pillar trim
panel and press on it un‐
til it clicks into place
3 - Nut
❑ Quantity: 2
❑ 4 Nm
4 - Vent
❑ Removing and Instal‐
ling. Refer to
⇒ “6.11.2 B-Pillar Upper
Trim Panel, Removing
and Installing”,
page 230 .
❑ Connect electrical har‐
ness connector, first in‐
sert lower vent in the
trim and press on it until
it engages audibly
5 - B-Pillar Upper Trim Panel
❑ byRemoving
Protected andforInstal‐
copyright. Copying private or commercial purposes, in part or in whole, is not
ling. Refer to
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Rear Carpet
❑ 4-Seater: two-piece
❑ 5-Seater: one-piece
❑ Removing and Instal‐
ling. Refer to
⇒ “6.14.2 Rear Carpet,
Removing and Instal‐
ling”, page 234 .
2 - Spacer
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
❑ Allocation. Refer
with respect to to the of information in this document. Copyright by AUDI AG.
the correctness
Parts Catalog.
3 - Front Carpet
❑ Driver side
❑ Removing and Instal‐
ling. Refer to
⇒ “6.14.1 Front Carpet,
Removing and Instal‐
ling”, page 233 .
4 - Front Carpet
❑ Front passenger side
❑ Removing and Instal‐
ling. Refer to
⇒ “6.14.1 Front Carpet,
Removing and Instal‐
ling”, page 233 .
5 - Floor Mat
❑ Quantity: 4
6 - Cap
❑ for floor mat
❑ Quantity: 2
❑ Unclip using the Pry
Lever - 80-200-
❑ Press into the bracket
until it clicks into place
7 - Bracket
❑ for floor mat
❑ Quantity: 2
❑ Insert from below into the floor mat
8 - Cap
❑ for floor mat
❑ Quantity: 2
❑ Unclip using the Pry Lever - 80-200-
❑ Press into the bracket until it clicks into place
9 - Bracket
❑ for floor mat
❑ Quantity: 2
❑ Insert from below into the carpet
10 - Expanding Clip
❑ Quantity: 2
9 - Rear Shelf
❑ Equipped on some models
❑ Allocation. Refer to the Parts Catalog.
❑ Removing and Installing. Refer to ⇒ “6.15 Rear Shelf, Removing and Installing”, page 235 .
❑ Insert the rear shelf in the rear window frame and press on the shelf until it clicks into place
10 - Clip
❑ Quantity: 2
❑ insert in the rear shelf
❑ Replace damaged or deformed clips
11 - Rear Shelf Support
❑ Only for 5 seats
12 - Expanding Clip
❑ Quantity: 2
❑ Remove using the Pliers - T40172C-
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
6.10 A-Pillar Trim Panel, Removing and In‐ with respect to the correctness of information in this document. Copyright by AUDI AG.
stalling
⇒ “6.10.1 A-Pillar Upper Trim Panel, Removing and Installing”,
page 226
⇒ “6.10.2 A-Pillar Lower Trim Panel, Removing and Installing”,
page 228
– Free up the A-pillar trim panel -1- in the area of the inner door
seal.
– Detach the A-pillar trim panel using the -3409- up to the first
retainer -arrows-.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Carefully remove the trim panel -1- upward out of the instru‐
ment panel -arrow-.
Installing
• Do not pinch the head curtain airbag when installing the upper
A-pillar trim panel.
– To install the trim panel, insert the new clip with the hooks into
the trim panel and bring it into its installation position.
– Insert the A-pillar trim panel -1- in the mount on the instrument
panel -arrow-.
Further installation is the reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.3 Overview - A-Pillar Trim Panel”, page 220 .
Removing
– Move the front seat all the way back.
– Remove the instrument panel side cover. Refer to
⇒ “4.2 Instrument Panel Side Cover, Removing and Installing”,
page 194 .
– Unclip the A-pillar gap cover -1- from below using the -3409-
-arrow- and disengage at the A-pillar upper trim panel.
Driver Side:
– Remove the operating lever for the hood release cable. Refer
to ⇒ Body Exterior; Rep. Gr. 55 ; Hood; Latch Release Lever,
Removing and Installing .
– Remove the screw -arrow A-.
Continuation for Both Vehicle Sides:
– Free up the A-pillar trim panel in the door seal area.
– Starting at the back, unclip the A-pillar trim panel -1- from the
side sill -B and C arrows- using the -3409- and remove toward
the rear.
– Remove the A-pillar trim panel.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.3 Overview - A-Pillar Trim Panel”, page 220 .
page 230 with respect to the correctness of information in this document. Copyright by AUDI AG.
Removing
– Unclip the sill panel -1- from the B-pillar lower trim panel. Refer
to ⇒ “6.9 Sill Panel, Removing and Installing”, page 226 .
– Unclip the A-pillar lower trim panel -3- from the B-pillar lower
trim panel. Refer to
⇒ “6.10.2 A-Pillar Lower Trim Panel, Removing and Installing”,
page 228 .
– Remove the expanding clips -4- with the -T40172C- .
– Move the front seat all the way forward.
– Unclip the B-pillar trim panel -2- from the B-pillar upper trim
panel -arrows- using the -3409- .
– Free up the B-pillar trim panel near the door seals and disen‐
gage it at the side from the B-pillar.
– Remove the B-pillar trim panel from the B-pillar and disconnect
the connector for the treble speaker.
– Remove the B-pillar trim panel upward.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.4 Overview - B-Pillar Trim Panel”, page 221 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– First, insert the B-pillar trim panel -3- upward into the mount
on the roof.
• The mount -2- for the sliding piece of the B-pillar trim must
engage in the retaining pin -1- on the seat belt height adjuster
-arrow-.
Further installation is the reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.4 Overview - B-Pillar Trim Panel”, page 221 .
Removing
– Remove the sill panel. Refer to
⇒ “6.9 Sill Panel, Removing and Installing”, page 226 .
– Remove the D-pillar trim panel. Refer to
⇒ “6.13 D-Pillar Trim Panel, Removing and Installing”,
page 232 .
– Remove the expanding clips -1 and 2-.
– Free up the C-pillar trim panel in the door seal area.
– Unclip the C-pillar trim panel -3- upward from the C-pillar trim
panel -arrow A- using the -3409- and pivot inward, to do so
push the headliner slightly upward.
– Remove the C-pillar trim panel upward -arrow B- and remove
it from the rear shelf.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.5 Overview - C-Pillar Trim Panel”, page 222 .
Installing
Install in reverse order of removal and note the following.
Equipped on some models:
– Insert the sun shade guide rail cover in the rear shelf.
– Engage the hooks -2- and tab -1- in the cover in the sun shade
guide rail and push in until it clicks into place.
– Perform a function test after installing.
• The sun shade must have ease of movement in the guide rail.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.6 Overview - D-Pillar Trim Panel”, page 223 .
Removing
– Remove the front seat. Refer to ⇒ Seats; Rep. Gr. 72 ; Front
Seats; Front Seat, Removing and Installing .
– Remove the front center console side trim panel. Refer to
⇒ “3.6.1 Front Center Console Trim Panel, Removing and In‐
stalling”, page 45 .
– Remove the A-pillar lower trim panel. Refer to
⇒ “6.10 A-Pillar Trim Panel, Removing and Installing”,
page 226 .
Driver Side:
– Remove the instrument panel cover on the driver side. Refer
to
⇒ “1.5 Driver Side Instrument Panel Cover, Removing and In‐
stalling”, page 22 .
Front Passenger Side:
– Reclining seat equipment version: remove the adapter rails.
Refer to ⇒ Seats; Rep. Gr. 72 ; Front Seats; Front Seat, Re‐
moving and Installing .
– Remove the glove compartment. Refer to
⇒ “1.10 Glove Compartment, Removing and Installing”,
page 26 .
⇒ “3.6.1 Front with Center Console Trim Panel,in Removing and In‐by AUDI AG.
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
respect to the correctness of information this document. Copyright
stalling”, page 45 .
– Remove the sill panels. Refer to
⇒ “6.9 Sill Panel, Removing and Installing”, page 226 .
– Remove the B-pillar lower trim panels. Refer to
⇒ “6.10.2 A-Pillar Lower Trim Panel, Removing and Installing”,
page 228 .
– Remove the floor mats.
– Remove the footwell vent trim -1- toward the rear from the air
duct in the floor -arrow-.
– Pull the rear shelf forward out of the mounts in thetorear windowof information in this document. Copyright by AUDI AG.
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect the correctness
frame -B arrows- and remove.
– To remove the rear shelf, remove the rear belt end fitting. Refer
to
⇒ “1.12 Outer Rear Belt End Fitting, Removing and Installing”,
page 87 .
NOTICE
There is a risk of damaging the speaker trim if handled incor‐
rectly.
– Carefully removing and installing the speaker trim.
– Carefully unclip
Protected by the speaker
copyright. Copying trim -1- orfrom
for private the rear
commercial shelf
purposes, in part or in whole, is not
-arrow- along
permittedthe seam
unless using
authorised theAG.
by AUDI -T10383/1-
AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Disengage the remaining tabs for the speaker trim along the
seam.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “6.8 Overview - Rear Shelf”, page 225 .
Removing
NOTICE
There is a risk of damaging the speaker trim if handled incor‐
rectly.
– Carefully removing and installing the speaker trim.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
6 - Gap Cover
❑ Removing and Installing. Refer to
⇒ “7.7 Luggage Compartment Side Trim Panel, Removing and Installing”, page 250 .
❑ Press on until it engages audibly
❑ Stretch the lip of the rear lid seal over
7 - Bolt
❑ Quantity: 2
❑ 8 Nm
8 - Tie Down
❑ Quantity: 2
❑ Removing and Installing. Refer to ⇒ “7.12 Tie Down, Removing and Installing”, page 255 .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Bracket
❑ For the tool box cover
❑ Engaged in the retaining
bracket
2 - Spare Wheel Well Trim
❑ Removing and Instal‐
ling. Refer to
⇒ “7.15 Spare Tire Well
Trim, Removing and In‐
stalling”, page 257 .
3 - Tool Box
❑ Equipped on some
models
❑ Allocation. Refer to the
Parts Catalog.
4 - Frame
❑ For the luggage com‐
partment floor panel
handle
❑ Can be pressed down in
one position on luggage
compartment floor pan‐
el handle
❑ Press on until it engages
audibly
5 - Handle
❑ For the luggage com‐
partment floor
❑ Removing and Instal‐
ling. Refer to
⇒ “7.14 Rear Luggage
Compartment Floor
Handle, Removing and
Installing”, page 255 .
6 - Luggage Compartment Floor
7 - Nut
8 - Vehicle Jack Mount
❑ Equipped on some models
❑ Allocation. Refer to the Parts Catalog.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Tie Down
❑ Quantity: 4
❑ Removing and Instal‐
ling. Refer to
⇒ “7.12 Tie Down, Re‐
moving and Installing”,
page 255 .
2 - Bolt
❑ Quantity: 8
❑ 8 Nm
3 - Front Tie Down Bracket
❑ Quantity: 2
❑ Removing and Instal‐
ling. Refer to
⇒ “7.13 Tie Down Brack‐
et, Removing and Instal‐
ling, Only e-tron”,
page 255 .
4 - Bolt
❑ Quantity: 2
❑ Replace after removing.
❑ Tightening specifica‐
tion. Refer to ⇒ Rep.
Gr. 93 ; High-Voltage
Battery Unit .
5 - Luggage Compartment
Floor
❑ With storage compart‐
ment cover
❑ Removing and Instal‐
ling. Refer to
⇒ “7.8 Luggage Com‐
partment Floor, Remov‐
ing and Installing, Only
e-tron”, page 253 .
6 - Bolt
❑ Quantity: 2
❑ 20 Nm
7 - Right Rear Tie Down Bracket Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
❑ Marked with »M« permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
❑ Removing and Installing. Refer to
⇒ “7.13 Tie Down Bracket, Removing and Installing, Only e-tron”, page 255 .
8 - Tire Mobility Kit Well
❑ Removing and Installing. Refer to
⇒ “7.15.2 Spare Tire Well Trim, Removing and Installing, Only e-tron”, page 257 .
9 - Left Rear Tie Down Bracket
❑ Marked with »L«
❑ Removing and Installing. Refer to
⇒ “7.13 Tie Down Bracket, Removing and Installing, Only e-tron”, page 255 .
10 - Handle
❑ For the storage compartment
1 - Expanding Clip
❑ Remove using the Pliers
- T40172C-
2 - Umbrella
❑ Removing and Instal‐
ling. Refer to
⇒ “7.9 Upper Luggage
Compartment Trim Pan‐
el, Removing and Instal‐
ling”, page 253 .
3 - Expanding Clip
❑ Quantity: 3
❑ Remove using the Pliers
- T40172C-
4 - Upper Luggage Compart‐
ment Trim Panel
❑ Allocation. Refer to the
Parts Catalog.
❑ Removing and Instal‐
ling. Refer to
⇒ “7.9 Upper Luggage
Compartment Trim Pan‐
el, Removing and Instal‐
ling”, page 253 .
5 - Cover Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
❑ for rear seat entertain‐ permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
ment with respect to the correctness of information in this document. Copyright by AUDI AG.
❑ Equipped on some
models
❑ Allocation. Refer to the
Parts Catalog.
❑ Removing and Instal‐
ling. Refer to
⇒ “7.9 Upper Luggage
Compartment Trim Pan‐
el, Removing and Installing”, page 253 .
6 - Clip
❑ Insert into the cover
❑ Remove any clips remaining in the rear lid mounting points using the Omega Clip Tool - T40280- . To
install, insert into the trim panel.
❑ Replace damaged or deformed clips
7 - Luggage Compartment Side Rear Panel Trim Panel
❑ Allocation. Refer to the Parts Catalog.
❑ Removing and Installing. Refer to
⇒ “7.10 Luggage Compartment Side Rear Panel Trim Panel, Removing and Installing”, page 254 .
❑ Removing and installing, with cooler. Refer to
⇒ G r.76 “Camper Cabinets, Shelves, Water Tank”, page 265 .
8 - Clip
❑ Quantity: 4
❑ Insert in the trim panel
❑ Remove any clips remaining in the rear lid mounting points using the Omega Clip Tool - T40280- . To
install, insert into the trim panel.
❑ Replace damaged or deformed clips
– To remove the expanding clips -1-, push the clamping pin -2-
in carefully approximately 5 mm until it engages audibly in the
expanding clip -arrow- (do not push in completely, otherwise
the clamping pin will be lost).
– Remove the released expanding clip with a clamping pin.
– Pull the rear lid hinge trim panel -3- downward out of the rear
lid trim panel and remove it.
– Repeat the process on the opposite side.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Unclip the rear lid trim panel -1- starting at the top of the rear
lid -A arrows- using the -T40233- .
– Unclip the side of the rear lid trim panel from the rear lid
-B arrows-.
– Unclip the lower rear lid trim panel from the rear lid
-C arrows- and remove.
Installing
Install in reverse order of removal and note the following:
– North America market-specific version: test the emergency
release function after installing the trim panel.
– Do this by locking the rear lid latch with a flat-head screwdriver
and operate the emergency release.
• The rear lid latch must unlock.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “7.5 Overview - Rear Lid Lower Trim Panel”, page 247 .
– Free up the gap cover -2- near the rear lid seal -1-.
– Release the gap cover -2- for the luggage compartment side
trim panel using the -3409- in the direction of the arrow -A- and
remove in the direction of the arrow -B-.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
– Free up the gap cover -2- near the rear lid seal -1-.
– Release the gap cover -2- for the luggage compartment side
trim panel using the -3409- in the direction of the arrow -A- and
remove in the direction of the arrow -B-.
On the right and left of the e-tron there is a respectively a fuel filler
door.
– Disengage and remove the upper luggage compartment side
trim panel on the rear lid hinge.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “7.2 Overview - Luggage Compartment Side Trim Panel”, page
241 .
– Unclip the upper rear panel trim panel -1- from the rear panel
-arrows- and pivot it toward the rear.
– Disengage the lower rear panel trim panel and remove.
Installing
Install in reverse order of removal.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “7.4 Overview - Upper Rear Panel/Luggage Compartment Trim
Panel”, page 246 .
Removing
– Remove the luggage compartment floor.
– Release the frame -1- on the bottom of the luggage compart‐
ment floor.
– To do this, position the -80 - 200- -arrow A-, and release the
frame -arrow B-.
– Release the frame and remove the luggage compartment floor
panel handle -2-.
Installing
Install in reverse order of removal and note the following:
– Position the frame -arrow- from below in the cut-out in the lug‐
gage compartment floor and hold.
1 - Headliner
❑ There are different ver‐
sions. Refer to the Parts
Catalog.
❑ Removing and Instal‐
ling. Refer to
⇒ “8.2 Headliner, Re‐
moving and Installing”,
page 258 .
2 - Clip
❑ For vehicles with sliding
sunroof
❑ Quantity: 15
❑ Insert in the headliner
❑ Replace damaged or
deformed clips
3 - Roof Reinforcement
❑ For vehicles without a
sliding sunroof
❑ Install on the body. Re‐
fer to
⇒ “8.3 Roof Reinforce‐
ment, Attaching to
Body”, page 261 .
4 - Roof Reinforcement
❑ For vehicles with sliding
sunroof
❑ Install on the body. Re‐ Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
fer to permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
⇒ “8.3 Roof Reinforce‐ with respect to the correctness of information in this document. Copyright by AUDI AG.
ment, Attaching to
Body”, page 261 .
5 - Clip
❑ Quantity: 4
❑ Insert in the headliner
❑ Remove any remaining clips in the body mounting points using the Omega Clip Tool - T40280- . To
install, insert into the headliner.
❑ Replace damaged or deformed clips
Removing
– Pay attention to the safety precautions when working with py‐
rotechnic components. Refer to
⇒ “1.4 Safety Precautions when Working with Pyrotechnic
Components”, page 4 .
– Position the single seat in the front, lowest position.
– Move the rear headrests into the lowest position.
– Remove the A-pillar upper trim panels. Refer to
⇒ “6.10.1 A-Pillar Upper Trim Panel, Removing and Installing”,
page 226 .
– Remove the upper B-pillar trim panels. Refer to
⇒ “6.11.2 B-Pillar Upper Trim Panel, Removing and Installing”,
page 230 .
– Remove the C-pillar trim panels. Refer to
⇒ “6.12 C-Pillar Trim Panel, Removing and Installing”,
page 231 .
– Remove the D-pillar trim panels. Refer to
⇒ “6.13 D-Pillar Trim Panel, Removing and Installing”,
page 232 .
– Remove the front roof module. Refer to ⇒ Electrical Equip‐
ment; Rep. Gr. 96 ; Controls; Front Interior Lamp/Reading
Lamp, Removing and Installing .
– Disconnect the connectors -arrows-.
– Equipped on some models: remove the front camera cover.
Refer to ⇒ page 62 .
– Remove the sun visors. Refer to
⇒ “2.3 Sun Visor, Removing and Installing”, page 31 .
– Remove the front vanity mirror illumination. Refer to ⇒ Elec‐
trical Equipment; Rep. Gr. 96 ; Lamps; Driver and Front
Passenger Vanity Mirror Lamps -W20- / -W14- , Removing
and Installing .
– Equipped on some models: remove the vanity mirror illumina‐
tion for the vehicle interior. Refer to ⇒ Electrical Equipment;
Rep. Gr. 96 ; Lamps ; Vanity Mirror for Vehicle Interior, Re‐
moving and Installing.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
NOTICE
There is a risk of damage due to improper handling.
– Do not kink the headliner.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
9 Revision History
DRUCK NUMBER:
Fac‐ Edit Job Fe Notes Quality
tory Edi‐ Type ed‐ Checke
Edi‐ tion ba d By
tion ck
10.2 01/1 Fac‐ N/ Joe Y
018 0/20 tory A
19 New
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1 - Bottle Holder
❑ Removing and Instal‐
ling. Refer to
⇒ “1.3.2 Bottle Holder,
Removing and Instal‐
ling”, page 268 .
2 - Storage Tray
❑ Removing and Instal‐
ling. Refer to
⇒ “1.3.1 Storage Tray,
Removing
Protected by copyright.and Instal‐
Copying for private or commercial purposes, in part or in whole, is not
ling”, page 268 .
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
3 - Nut
❑ Quantity: 4
❑ Replace after removing.
❑ 8 Nm
4 - Bolt
❑ Quantity: 4
5 - Cooler - J698-
❑ Unit with compressor
❑ Removing and Instal‐
ling. Refer to
⇒ “1.2 Cooler, Remov‐
ing and Installing”, page
266 .
6 - Bracket
❑ Quantity: 2
❑ For securing int he lug‐
gage compartment
❑ Removing and Instal‐
ling. Refer to
⇒ “1.2 Cooler, Remov‐
ing and Installing”, page
266 .
7 - Bolt
❑ Quantity: 6
❑ Install with locking compound. Refer to the ⇒ Electronic Parts Catalog (ETKA) for the locking compound.
❑ 1.5 Nm
8 - Clip
❑ Quantity: 2
9 - Cooler Trim Panel
❑ Removing and Installing. Refer to ⇒ “1.2 Cooler, Removing and Installing”, page 266 .
1. Cooler 265
Audi A8 2018 ➤
Body Interior - Edition 10.2018
10 - Clip
❑ Quantity: 2 each
11 - Left Rear Panel Trim Panel
❑ Removing and Installing. Refer to ⇒ “1.2 Cooler, Removing and Installing”, page 266 .
12 - Right Rear Panel Trim Panel
❑ Removing and Installing. Refer to ⇒ “1.2 Cooler, Removing and Installing”, page 266 .
– Loosen the cooler trim panel -1- from the catches -arrow- and
remove it toward the rear.
– Remove the left rear seat. Refer to ⇒ Seats; Rep. Gr. 72 ;
Rear Seats; Rear Seat Backrest, Removing and Installing .
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
1. Cooler 267
Audi A8 2018 ➤
Body Interior - Edition 10.2018
Installing
Removing
Crash Sensor
– Open the cooler cover.
– Remove the seal -2- upward from the cover -1-.
Installing
Install in reverse order of removal and note the following:
– The seal must be completely pressed in the mount.
Installation instructions: for example tightening specifications, re‐
placing components. Refer to
⇒ “1.1 Overview - Cooler”, page 265 .
Please read these WARNINGS and CAUTIONS before proceeding with maintenance and
repair work. You must answer that you have read and you understand these WARNINGS and
CAUTIONS before you will be allowed to view this information.
If you lack the skills, tools and equipment, or a suitable workshop for any procedure described
in this manual, we suggest you leave such repairs to an authorized Audi retailer or other
qualified shop. We especially urge you to consult an authorized Audi retailer before beginning
repairs on any vehicle that may still be covered wholly or in part by any of the extensive
warranties issued by Audi.
Disconnect the battery negative terminal (ground strap) whenever you work on the fuel system
or the electrical system. Do not smoke or work near heaters or other fire hazards. Keep an
approved fire extinguisher handy.
Audi is constantly improving its vehicles and sometimes these changes, both in parts and
specifications, are made applicable to earlier models. Therefore, part numbers listed in this
manual are for reference only. Always check with your authorized Audi retailer parts
department for the latest information.
Any time the battery has been disconnected on an automatic transmission vehicle, it will be
necessary to reestablish Transmission Control Module (TCM) basic settings using the Audi
Factory Approved Scan Tool (ST).
Never work under a lifted vehicle unless it is solidly supported on stands designed for the
purpose. Do not support a vehicle on cinder blocks, hollow tiles or other props that may
crumble under continuous load. Never work under a vehicle that is supported solely by a jack.
Never work under the vehicle while the engine is running.
For vehicles equipped with an anti-theft radio, be sure of the correct radio activation code
before disconnecting the battery or removing the radio. If the wrong code is entered when the
power is restored, the radio may lock up and become inoperable, even if the correct code is
used in a later attempt.
If you are going to work under a vehicle on the ground, make sure that the ground is level.
Block the wheels to keep the vehicle from rolling. Disconnect the battery negative terminal
(ground strap) to prevent others from starting the vehicle while you are under it.
Do not attempt to work on your vehicle if you do not feel well. You increase the danger of
injury to yourself and others if you are tired, upset or have taken medicine or any other
substances that may impair you or keep you from being fully alert.
Never run the engine unless the work area is well ventilated. Carbon monoxide (CO) kills.
Always observe good workshop practices. Wear goggles when you operate machine tools or
work with acid. Wear goggles, gloves and other protective clothing whenever the job requires
working with harmful substances.
Tie long hair behind your head. Do not wear a necktie, a scarf, loose clothing, or a necklace
when you work near machine tools or running engines. If your hair, clothing, or jewelry were to
get caught in the machinery, severe injury could result.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Page 1 of 3
© 2018 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Version 2.0
Cautions & Warnings
Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are
designed to be used only once and are unreliable and may fail if used a second time. This
includes, but is not limited to, nuts, bolts, washers, circlips and cotter pins. Always follow the
recommendations in this manual - replace these fasteners with new parts where indicated,
and any other time it is deemed necessary by inspection.
Illuminate the work area adequately but safely. Use a portable safety light for working inside or
under the vehicle. Make sure the bulb is enclosed by a wire cage. The hot filament of an
accidentally broken bulb can ignite spilled fuel or oil.
Friction materials such as brake pads and clutch discs may contain asbestos fibers. Do not
create dust by grinding, sanding, or by cleaning with compressed air. Avoid breathing
asbestos fibers and asbestos dust. Breathing asbestos can cause serious diseases such as
asbestosis or cancer, and may result in death.
Finger rings should be removed so that they cannot cause electrical shorts, get caught in
running machinery, or be crushed by heavy parts.
Before starting
Protectedabyjob, make
copyright. certain
Copying thator you
for private havepurposes,
commercial all thein necessary
part or in whole, tools
is not and parts on hand.
Read all the instructions
permitted thoroughly,
unless authorised by AUDI AG.do AUDInot
AG attempt shortcuts.
does not guarantee or acceptUse tools that are appropriate to
any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
the work and use only replacement parts meeting Audi specifications. Makeshift tools, parts
and procedures will not make good repairs.
Catch draining fuel, oil or brake fluid in suitable containers. Do not use empty food or
beverage containers that might mislead someone into drinking from them. Store flammable
fluids away from fire hazards. Wipe up spills at once, but do not store the oily rags, which can
ignite and burn spontaneously.
Use pneumatic and electric tools only to loosen threaded parts and fasteners. Never use these
tools to tighten fasteners, especially on light alloy parts. Always use a torque wrench to tighten
fasteners to the tightening torque listed.
Keep sparks, lighted matches, and open flame away from the top of the battery. If escaping
hydrogen gas is ignited, it will ignite gas trapped in the cells and cause the battery to explode.
Be mindful of the environment and ecology. Before you drain the crankcase, find out the
proper way to dispose of the oil. Do not pour oil onto the ground, down a drain, or into a
stream, pond, or lake. Consult local ordinances that govern the disposal of wastes.
The air-conditioning (A/C) system is filled with a chemical refrigerant that is hazardous. The
A/C system should be serviced only by trained automotive service technicians using approved
refrigerant recovery/recycling equipment, trained in related safety precautions, and familiar
with regulations governing the discharging and disposal of automotive chemical refrigerants.
Before doing any electrical welding on vehicles equipped with anti-lock brakes (ABS),
disconnect the battery negative terminal (ground strap) and the ABS control module
connector.
Do not expose any part of the A/C system to high temperatures such as open flame.
Excessive heat will increase system pressure and may cause the system to burst.
Page 2 of 3
© 2018 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Version 2.0
Cautions & Warnings
When boost-charging the battery, first remove the fuses for the Engine Control Module (ECM),
the Transmission Control Module (TCM), the ABS control module, and the trip computer. In
cases where one or more of these components is not separately fused, disconnect the control
module connector(s).
Some of the vehicles covered by this manual are equipped with a supplemental restraint
system (SRS), that automatically deploys an airbag in the event of a frontal impact. The airbag
is operated by an explosive device. Handled improperly or without adequate safeguards, it can
be accidentally activated and cause serious personal injury. To guard against personal injury
or airbag system failure, only trained Audi Service technicians should test, disassemble or
service the airbag system.
Do not quick-charge the battery (for boost starting) for longer than one minute, and do not
exceed 16.5 volts at the battery with the boosting cables attached. Wait at least one minute
before boosting the battery a second time.
Never use a test light to conduct electrical tests of the airbag system. The system must only
be tested by trained Audi Service technicians using the Audi Factory Approved Scan Tool (ST)
or an approved equivalent. The airbag unit must never be electrically tested while it is not
installed in the vehicle.
Some aerosol tire inflators are highly flammable. Be extremely cautious when repairing a tire
that may have been inflated using an aerosol tire inflator. Keep sparks, open flame or other
sources of ignition away from the tire repair area. Inflate and deflate the tire at least four times
before breaking the bead from the rim. Completely remove the tire from the rim before
attempting any repair.
When driving or riding in an airbag-equipped vehicle, never hold test equipment in your hands
or lap while the vehicle is in motion. Objects between you and the airbag can increase the risk
of injury in an accident.
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.
Page 3 of 3
© 2018 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of
this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.
Version 2.0