Professional Documents
Culture Documents
JK Wall Putty Data Sheet
JK Wall Putty Data Sheet
White Cement
based Putty
DJ.K. Wall Putty is a white cement based fine powder which provides an ideal finishing for concrete / cement
plastered walls and ceiling.
DIt Provides an ideal base for painting.
DIt provides damp resistant smooth finish for further application of all kinds of paints. (Damp resistance means
resistance to water in humid air & not physical water contacts / leakages).
DIt gives pleasing look to interiors & exteriors.
DIt is fine powder to be mixed with water as advised for direct application on plastered surface of the interiors /
exteriors to get silky and shiny finish.
DCan be used on concrete, rendered wall, hollow block, precast walls, concrete ceilings, calcium silicate bricks &
aerated light weight blocks.
DNot recommended for use on painted or other non-cementitious surfaces.
PRODUCT OF :
J.K. WHITE CEMENT
SURFACE PREPARATION * Just-wet condition could be achieved by
New Surface applying coat of water with soft brush.
New surface requires preparation such as removal of dust, ** In case of wall exposed to sun, more water
dirt and foreign matter. In case of cracks, voids & damages it spraying shall be done to take away heat from the
should be repaired. Surface should be in just-wet condition, surface and then bring wall to just-wet condition.
prior to putty application .
PREPARATION OF J. K. WALL PUTTY PASTE
Old Unpainted Surface
All loose material, organic growth, dirt, dust, etc. must be ! Mix J. K. Wall Putty slowly in @ 35 - 40%
removed with steel blade or wire brush. Surface should be in water by volume to prepare paste of
just-wet condition, prior to putty application. desired consistency.
! Mix vigorously for 5-10 minutes for making
Old Painted Surface lump free and uniform paste, as shown.
Scrub the surface with coarse wire brush / sand paper and
! Product should be mixed in such quantities
clean thoroughly so that it is free from old paint / dust
that it could be used within 2 hrs of its
particles till the cementitious / plastered surface is seen.
preparation.
Surface could be washed with water, however ensuring that
surface should be in just-wet condition, prior to putty ! Mixing could be done manually or by
application. suitable electric mixer.
WETTING
Usual curing with lot of water is not needed. PACKAGING
Keeping in view the ambient temperature, need
! 1 kg P.P. packets put in 20 kg secondary HDPE bag for
based wetting is recommended.
ease of handling.
! Just-wet the surface, prior to putty application. ! 5 kg packs put in 20 kg secondary HDPE bag for ease of
! After applying first coat wet the surface gently. handling.
! After application of second coat, wet surface ! 20 kg HDEP bag put into 20 kg laminated P.P. bag.
twice a day for at least one day, if season ! 40 kg HDEP bag put into 20 kg laminated P.P. bag.
demands it. Water shall be applied gently.
Performance at a Glance
Properties J.K. Wall Putty Traditional putty POP
Area of Can be applied on exterior/exposed Can't be applied on exterior/ Can't be applied on exterior
Application surface / interior / ceiling exposed surface. /exposed surface
Binding Property Cement based putty, Very low binding property Low binding property.
hence good binding property. due to use of chalk powder .
Coverage Area 14 sq.ft / kg. on @ 10 sq. ft / kg 6-7 sq. feet /kg for equivalent
new smooth plastered wall for for equivalent thickness. thickness.
finished thickness.
Consistency Consistency in quality as it is Large variation in properties. Huge variation in quality
Factory made with standard Quality of ingredients varying
ingredients & continuous from area to area.
quality control.
Cosumption of Less Distemper is required Requires more Distemper Requires more Distemper
Distemper because of its low absorption. because of high absorption. because it's absorption is more.
Cost Less ultimate cost due to Ultimate cost is high. Ultimate cost is
long life span, No Primer cost, quite high.
low paint absorption.
Look Better appearance due to Appearance is not like JKWP Yellow surface is achieved
very high whiteness (Min.93%) due to its yellowish base.
of Putty.
Water Resistance good resistance to dampness. It doesn't resist dampness Peels off when comes in
contact with water
Structural problems could not be taken care of by the finishing / decoration material. Therefore, adequate quality assurance
of structure is strongly recommended. We are available for technical experience sharing at any stage of the project.
Please contact : E-mail mpr@jk-white.com
Note : Information given in this booklet is for general guidance. Specific instruction for various site conditions can be furnished on
demand. However, Company is not responsible for any wrong application of the product.