Professional Documents
Culture Documents
Model UC-2 Installation Instructions
Model UC-2 Installation Instructions
Model UC-2
Two Stage Under Counter System
Wa r n i n g Please read carefully before proceeding with installation. Your failure to follow any attached instructions or operating parameters may lead to the product's failure and possible damage to property.
NSF
System Tested and certified by NSF International Against ANSI/NSF Standard 53 for the reduction of claims specified on performance data sheet. Refer to enclosed warranty for operating parameters to ensure proper use with your water supply.
Watts Pure Water, Inc. 1725 W. Williams Dr. #C-20 Phoenix, AZ 85027 Phone: 888-774-7405 Fax: 602-588-0356
Thank You!
Thank you for your purchase of a Watts Pure Water Reverse Osmosis system. With proper installation and maintenance, this system will provide you with high quality water for years to come. All of Watts Pure Water's water enhancement products are rigorously tested by independent laboratories for safety and reliability. If you have any questions or concerns, please contact your local distributor or call us at 1-888-774-7405 (outside USA 623-505-1512).
Table of Contents
Tools & Materials Recommended for Normal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Operational Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Filter Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Exploded Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Operational Parameters
1. Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. System certified for cyst reduction may be used on disinfected water that may contain filterable cysts. 2. Operating Temperatures: Maximum 100F (40C) Minimum 40F (04.4C) 3. Operating Pressure: Maximum 100 psig (7.43 kg/cm2) Minimum 5 psig (0.35 kg/cm2) 4. pH: 6.0 to 8.5 5. Maximum flow rate: 0.5 GPM @ 60 psig 1.82 LPM @ 4.20 kg/cm2
Sink Green Tubing
HOT
COLD
Installation
This system has been designed to fit under most kitchen sinks. Please read carefully before proceeding with installation.
B. Determine the desired location for the faucet on your sink surface. C. Place a piece of masking tape or duct tape on location where the hole is to be drilled. Mark the center of the hole on the tape. Note: Stainless steel sinks only go Step F. D. Using the variable speed drill on the slowest speed, drill a 1/8" (3mm) pilot hole at the center of the desired location. Use lubricating oil or liquid soap to keep the drill bit cool while drilling. Note: If drill bit gets hot it may cause the porcelain to crack or chip. Pilot hole must be drilled through both porcelain and metal casing of the sink before proceeding to the next step. E. Enlarge pilot hole to 1/4" (6.4mm). Keep drill speed on the slowest speed and use lubricating oil or liquid soap to keep drill bit cool. F. Enlarge the 1/4" hole to 7/16" (11.13mm). Keep drill speed on the slowest speed and use lubricating oil or liquid soap to keep drill bit cool. G. Pass the Escutcheon plate and black rubber washer over threaded mounting tube at the base of the faucet body. H. From top of sink pass the threaded mounting tube through the hole drilled in the sink. Align the faucet body. I. From under the sink, slide the locating washer and the lockwasher over the threaded tube part of the faucet. Screw on retaining nut. Tighten with wrench. J. Connect the loose end of the 1/4" blue plastic tubing from the filtration unit to the threaded mounting tube of the faucet as shown Figure B.
Handle Faucet Body Escutcheon Plate Black Rubber Washer Locking Washer Retaining Nut / " Brass Insert / " Delrin Sleeve Figure A
1 4
Delrin Sleeve beveled end faces end of Tubing Brass Insert goes inside of Tubing
Locating Washer
1 4
Figure B
Note: Remove plastic tubing from faucet body before inserting long reach spout into faucet body. Note: If using existing hole (sprayer or soap dispenser) go to Step G. 3
Nut Tubing
Gasket Figure C1
Sink Faucet
Gasket
1 2
Step 4: Start Up
A. Lift black faucet handle up on faucet to start flow of water through unit. Run 7 gallons of water through unit. Close faucet. Note: You may hear some noise as air is being purged from the unit. The first few ounces of water from the unit may be dark in color due to carbon fines from the filter. B. Your water is now ready for drinking.
Figure C2
Filter Change
Watts Pure Water recommends changing the filter element at least every 6 months or 1350 gallons (5100 liters). Use Watts' P-CB-1 replacement cartridge only. A. Turn off incoming feed water supply to unit. Note: There will be water in the unit filter housing. Lift the faucet handle to relieve the water pressure. B. Remove filter housing from lid by unscrewing to the left, as shown in Figure D. C. Remove used filter cartridges and discard. Discard the P-CB-1 gaskets. Note: Do not discard the filter housing O-ring. D. Clean inside of filter housing with warm soapy water. Rinse the filter housing with warm clean water to remove soap. E. Lubricate filter housing O-ring with water-soluble lubricant (i.e. K-Y Jelly or Silicone lubricant) Note: Do not use Petroleum base lubricant (i.e. Vaseline). F. Seat O-ring in groove in filter housing. G. Insert new filter cartridges into filter housing. H. With the filter bowl in a upright position, screw filter housing back onto lid as shown in Figure D. I. Repeat Start Up procedure (Step 4) and check for leaks.
Figure D To Loosen To Tighten
20
6 21
7 8
5 1
10
18
2 3 4
Item 1 2 3 4 5 6 7 8 9 a 10 11
Part # 134008 131017 131012 131002 140007 125034 113004 113029 101015
Item 12 13 14 15 16 17 18 19 20 21 22
Part #
/ " Brass Insert / " Delrin Sleeve / " C Brass Nut / " Green Tubing (4ft) / "C x 1/4" MPT 90 Elbow / " FPT Black Lid
Black Rubber Washer Escutcheon Plate Faucet Body L/R Spout Twin Bracket #103/4" Philip Pan Head Screw (10)
1/4" Heavy Duty Brass Hex Nipple
O- Ring For Filter Housing P-CB-1 1-Micron Carbon Block Gasket for Carbon Block (2)
113017 140004
Limited Warranty
What your Warranty Covers: If any part of your WATTS PURE WATER Reverse Osmosis System is defective in workmanship (excluding replaceable filters and membranes), return unit after obtaining a return authorization (see below), less tank, within 3 years of original retail purchase. WATTS PURE WATER will repair or, at WATTS PURE WATER'S option, replace the system at no charge. How to obtain Warranty Service: For warranty service, call 1-800-752-5582 for a return authorization number. Then, ship your Reverse Osmosis unit (less tank) to our factory, freight and insurance prepaid, with proof of date of original purchase. Please include a note stating the problem. WATTS PURE WATER will repair it, or replace it, and ship it back to you prepaid. What this warranty does not cover: This warranty does not cover defects resulting from improper installation, (contrary to WATTS PURE WATER'S printed instructions), from abuse, misuse, misapplication, improper maintenance, neglect, alteration, accidents, casualties, fire, flood, freezing, environmental factors, or other such acts of God. This warranty will be void if defects occur due to failure to observe the following conditions: 1. The Reverse Osmosis System must be hooked up to a potable municipal or well cold water supply. 2. The hardness of the water should not exceed 7 grains per gallon, or 120 ppm. 3. Maximum incoming iron must be less than 0.2 ppm. 4. The pH of the water must not be lower than 3 or higher than 11. 5. The incoming water pressure must be between 40 and 100 pounds per square inch. 6. Incoming water to the RO cannot exceed 105 degrees F (40 degrees C.) 7. Incoming TDS/Total Dissolved Solids not to exceed 1800 ppm. 8. Do not use with water that is micro-biologically unsafe or of unknown quality without adequate disinfection before or after the system. This warranty does not cover any equipment that is relocated from the site of its original installation. This warranty does not cover any equipment that is installed or used outside the United States of America. LIMITATIONS AND EXCLUSIONS: WATTS PURE WATER WILL NOT BE RESPONSIBLE FOR ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. WATTS PURE WATER WILL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING TRAVEL EXPENSE, TELEPHONE CHARGES, LOSS OF REVENUE, LOSS OF TIME, INCONVENIENCE, LOSS OF USE OF THE EQUIPMENT, AND DAMAGE CAUSED BY THIS EQUIPMENT AND ITS FAILURE TO FUNCTION PROPERLY. THIS WARRANTY SETS FORTH ALL OF WATTS PURE WATER'S RESPONSIBILITIES REGARDING THIS EQUIPMENT. OTHER CONDITIONS: If WATTS PURE WATER chooses to replace the equipment, WATTS PURE WATER may replace it with reconditioned equipment. Parts used in repairing or replacing the equipment will be warranteed for 90 days from the date the equipment is returned to you or for the remainder of the original warranty period, whichever is longer. This warranty is not assignable or transferable. YOUR RIGHTS UNDER STATE LAW: Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply. This warranty gives you specific legal rights, and you may have other legal rights which vary from state to state.
Telephone #
623 505-1511 973 427-2898 631 253-0600 508 238-2030 724 745-5300 804 643-7355 703 866-3111 215 443-7500 716 741-9575 504 602-8100 601 856-7565 787 769-0085 205 879-3469 615 259-9944 901 795-0045 704 525-3388 770 447-1227 407 245-7838
Fax #
602 588-0356 973 427-4246 631 253-0303 508 238-8353 724 745-7420 804 643-7380 703 866-2332 215 443-7573 716 741-4810 504 602-8106 601 856-8390 787 750-5120 205 870-5027 615 259-5111 901 795-0394 704 525-6749 770 263-6899 407 245-7833
Edwards, Platt & Deely, Inc. Edwards, Platt & Deely, Inc. W. P. Haney Co., Inc. J. B. OConnor Company, Inc. RMI The Joyce Agency, Inc. Vernon Bitzer Associates, Inc. WMS Sales, Inc. (Main office) Billingsley & Associates, Inc. Billingsley & Associates, Inc. Francisco J. Ortiz & Co., Inc. Mid-America Marketing, Inc. Mid-America Marketing, Inc. Mid-America Marketing, Inc. Smith & Stevenson Co., Inc. Spotswood Associates, Inc. Target Marketing Enterprises, Inc. Aspinall Associates, Inc. Dave Watson Associates Disney-McLane-Woodcock, Inc. Disney-McLane-Woodcock, Inc. Mid-Continent Marketing Services Ltd. Soderholm & Associates, Inc. Stickler & Associates Hugh M. Cunningham, Inc. Mack McClain & Associates Mack McClain & Associates, Inc. Mack McClain & Associates, Inc. Pro-Spec, Inc. Phoenix Marketing, Ltd. Delco Sales, Inc. Delco Sales, Inc. Fanning & Associates, Inc. Hollabaugh Brothers & Associates Hollabaugh Brothers & Associates P I R Sales, Inc. R. E. Fitzpatrick Sales, Inc. Zurier Company Watts Industries (Canada) Inc. (Watts Regulator Co. Division) Allan Forrest Sales Ltd. Allan Forrest Sales Ltd. Hy-Line Sales Ltd. Hydro-Mechanical Sales, Ltd. Hydro-Mechanical Sales, Ltd. Hydro-Mechanical Sales, Ltd. Le Groupe B.G.T., Inc. Le Groupe B.G.T., Inc. Mar-Win Agencies, Ltd. Palser Enterprises, Ltd. Palser Enterprises, Ltd. Mech-Tech Sales RAM Mechanical Marketing RAM Mechanical Marketing Walmar Mechanical Sales EXPORT Hdqtrs.: Watts Regulator Co.
317 849-5757 317 845-7967 517 263-8988 517 263-2328 800 542-1682 877 476-1682 216 486-1010 216 486-2860 630 953-1211 630 953-1067 763 427-9635 763 427-5665 414-771-0400 414-771-3607 972 888-3808 972 888-3838 314 894-8188 314 894-8388 515 288-0184 515 288-5049 913 339-6677 913 339-9518 918 461-0066 918 461-0105 505 883-7100 505 883-7101 714 888-2444 714 888-2448 808 842-7900 808 842-9625 303 289-4191 303 286-9069 253 867-5040 253 867-5055 503 238-0313 503 235-2824 480 892-6000 480 892-6096 801 282-0700 801 282-0600 925 449-5858 925 449-7878
Western
South Central
North Central
5435 North Service Road, Burlington, Ontario L7L 5H7 #10, 4980 12A Street S.E., Calgary, Alberta T2G 5K9 12514B - 128th St., Edmonton, Alberta T5L 1C8 1 19661-96th Ave., Langley, British Columbia V1M 3C9 3700 Joseph Howe Dr., Ste. 1 Halifax, Nova Scotia B3L 4H7 297 Collishaw St., Ste. 7 (shipping) Moncton, New Brunswick E1C 9R2 85 Tolt Rd., St. Phillips, Newfoundland A1B 3M7 2800 Rue Dalton Ste. 3, Ste-Foy, Quebec G1P 3S4 86 des Enterprises #208, Boisbriand, Quebec J7G 2T3 1123 Empress St., Winnipeg, Manitoba R3E 3H1 1885 Blue Heron Dr., #4, London, Ontario N6H 5L9 160 Pennsylvania Avenue, Concord, Ontario L4K 4A9 1069 Gordon Ave., Sudbury, Ontario P3A 2V5 441 Quebec St., Regina, Saskatchewan S4R 1K8 #13 1100 7th. Avenue North, Saskatoon, Saskatchewan S7K 2V9 24 Gurdwara Rd., Nepean, Ontario K2E 8B5 815 Chestnut St., North Andover, MA 01845-6098 U.S.A.
905 332-4090 403 243-7001 780 452-8551 604 888-3114 902 443-2274 506 859-1107 709 895-0090 418 657-2800 450 434-9010 204 775-8194 519 471-9382 905 738-5200 705 525-2543 306 525-1986 306 244-6622 613 225-9774 978 688-1811
905 332-7068 403 243-7353 780 452-3486 604 888-3070 902 443-2275 506 859-2424 709 895-0091 418 657-2700 450 434-9848 204 786-8016 519 471-1049 905 738-6111 705 525-0432 306 525-0809 306 244-0807 613 225-0673 978 794-1848
0328
Canada
IOM-UC-2 0342
EDP# 1915890
Printed in U.S.A.