Professional Documents
Culture Documents
24012017ii Btech Ece I Mid PDC Question Bank
24012017ii Btech Ece I Mid PDC Question Bank
QUESTION BANK
Name of the branch: ECE Year & Sem:II-II
Name of the subject: PULSE &DIGITAL CIRCUITS
Name of the faculty, Designation & Mobile number:G LAXMAN,Asst.Prof,9963933378
Date of Examination: Academic Year: 2016-17
NOTE: All the faculty requested to use Question Style - Calibri and Size - 12
UNIT-I
LINEAR WAVE SHAPING
APPEARED IN
MARKS
S.N0 QUESTION (R05,R07,
Assigned
R09, R13)
1. Prove that for any periodic input wave form the average
1 levels of the steady state output signal from RC high pass circuit
is always zero R09 16
2. (a) Write a short notes on RC low pass circuit
(b) Draw the output response of RC low pass circuit for a step
2 input signal and explain in detailed.
c)Explain how a low pass RC circuit act as an integrator.
R09 6+6+4
3. (a) Explain about RLC Ringing Circuit
3 (b) Explain RC double differentiator circuit.
R07 8+8
4.(a) A symmetrical square wave whose peak-to-peak amplitude
is 2V and whose average value is zero is applied to an RC
integrating circuit. The time constant is equal to half -period of
4 the square wave. Find the peak to peak value of the output
amplitude.
(b) Describe the relationship between rise time and RC time
constant of a low pass RC circuit. R09 8+8
5. (a) Explain the response of RL circuit when a step input signal
is applied
5
(b) In a low pass RC circuit, R=2k and C = 1_ F =1.sv, 2ms, pulse is
applied as input to this circuit sketch the output wave form. R07 8+8
6(a) Obtain the response of RC high pass circuit for an
6 exponential i/p signal.
R09 8+8
(b) A square wave whose peak-to-peak value is 1V, extends
_0.5v (0.5V w.r.t.to ground). The half period is 0.1 sec this
voltage impressed upon an RC differentiating circuit whose time
constant is 0.2 sec. Determine the maximum and minimum
values of the O/p voltages in the steady state.
7. (a) The limited ramp is applied to an RC differentiator. Draw
to scale, the output wave form for the following cases
i. T=RC,
7 ii. T=0.4RC,
iii. T=10RC.
(b) Derive the expression for the response of RC low pass circuit
to which ramp input is applied. R07 8+8
8.a) The output of a high pass RC circuit for a symmetrical
square wave input is shown in Figure.1. Derive the expression
for percentage tilt in the output.
UNIT-II
NON LINEAR WAVESHAPING
APPEARED IN
MARKS
S.N0 QUESTION (R05,R07,
Assigned
R09, R13)
1(a) Draw the diode comparator circuit and explain the
1
operation of it when ramp input signal is applied.
(b) Explain the operation of two level slicer.
R09 10+6
2. (a) Draw the basic circuit diagram of negative peak clamper
circuit and explain its operation.
2
(b) What is meant by comparator and explain diode
differentiator comparator operation with the help of ramp input
signal is applied.
R09 6+10
3. (a) Draw the basic circuit diagram of a DC restorer circuit and
explain its operation. Sketch the output wave form for a
3
sinusoidal input.
(b) Draw the basic circuit diagram of positive peak clamper
circuit and explain its operation.
R09 8+8
4
4.a)Draw the circuit diagram of an Emitter-Coupled clipping
circuit. Explain its operation with its transfer
characteristic and necessary expressions R09 8+7
b) State and prove clamping circuit theorem.
R07 8+8
b) A 100V peak square wave with an average value of 0V and a
period of 20 ms is to be negatively clamped at 25V. Draw the
circuit diagram necessary for this purpose. Also, draw the input
and output waveforms.
10.For the circuit shown in, make a plot of V0 against Vi for the
range of Vi from 0 to 50V. Indicate all slopes and voltage levels,
and diode conducting region. Assume ideal diodes.
10
R09 16
11 (a) A symmetrical 10 kHz square wave whose peak -to-peak
excursion are _10V with respect to ground is impressed upon
the diode clamping circuit shown in. The Diodes has Rf = 100 , Rr
= _ and V = 0. Sketch the steady state output waveform
Indicating clearly the voltage levels.
11
12
14
15