Professional Documents
Culture Documents
Service Manual: M PL Ifi Ed
Service Manual: M PL Ifi Ed
MTNC020515A1
B1
ed
il fi Simplified Manual
p (NA7DM)
im
S
Panasonic
Models Chassis
CT-20G7DF AP391
CT-20D12DF BP391
This supplement service manual is issued to add the modelss of the NA7DM family listed above to the main service
manual order No. MTNC010305C1 (CT-20D11E). Included in this supplement service manual are unique
characteristics and a complete parts list. Please file and use this simplified service manual together with main service
manual order No. MTNC010305C1
“WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Productspoweredbyelectricityshouldbeservicedorrepairedonlybyexperiencedprofessionaltechnicians.Anyattempttoservice
or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.”
The service technician is required to read and follow the “safety precautions” and “important safety notice” in this main manual.
-3-
Service notes
Note: These components are affixed with glue. Be careful not to break or damage any foil under the
component or at the pins of the ICs when removing. Usually applying heat to the component for a short time
while twisting with tweezers will break the component loose.
Leadless chip component How to replace Flat-IC
(surface mount) - Required tools -
Chip components must be replaced with identical chips • Soldering iron • De-solder braids
due to critical foil track spacing. There are no holes in
the board to mount standard transistors or diodes. • Sharpen pliers (wire • Magnifier
Some chips capacitor or resistor board solder pads cutters and long nose)
may have holes through the board, however the hole 1. Cut the pins of the defective IC with the wire cutters
diameter limits standard resistor replacement to 1/8 pliers, and remove it completely away from the
watt. Standard capacitor may also be limited for the board. If the IC is glued to the board, apply hot air
same reason. It is recommended that identical to complete the removal. CAUTION- Do not pull or
components be used. twist the pliers, may damage the soldering pads in
Chip resistor have a three digit numerical resistance the board.
code - 1st and 2nd significant digits and a multiplier. Flat-IC
Example: 162 = 1600 or 1.6kΩ resistor, 0 = 0Ω (jumper).
Chip capacitors generally do not have the value
indicated on the capacitor. The color of the component
indicates the general range of the capacitance.
Chip transistors are identified by a two letter code. The 2. Using the soldering Iron and the long nose pliers,
remove the IC pins that still attached to the board.
first letter indicates the type and the second letter, the
grade of transistor.
Chip diodes have a two letter identification code as per
the code chart and are a dual diode pack with either
common anode or common cathode. Check the parts
Soldering
list for correct diode number. iron
Component removal 3. Using the de-solder braid and the soldering iron,
1. Use solder wick to remove solder from component remove the solder from the board soldering pads.
end caps or terminal. De-Solder
2. Without pulling up, carefully twist the component braid
with tweezers to break the adhesive. Soldering
3. Do not reuse removed leadless or chip iron
components since they are subject to stress
fracture during removal. 4. Position the new Flat-IC in place (apply the pins of
the Flat-IC to the soldering pads where the pins
Chip component Installation need to be soldered). Properly determine the
1. Put a small amount of solder on the board positions of the soldering pads and pins by
soldering pads. correctly aligning the polarity symbol. Start aligning
2. Hold the chip component against the soldering and soldering pin no.1, then align and solder the
pads with tweezers or with a miniature alligator clip
pin in the apposite corner of the IC, this will help to
and apply heat to the pad area with a 30 watt iron
until solder flows. Do not apply heat for more than align the rest of the pins.
3 seconds. Polarity
symbol
TYPE Chip components SOLDER
CAPS
GRADE
c
5. Solder all pins to the soldering pads using a fine
tipped soldering iron.
b
e
TRANSISTOR CAPACITOR
1ST DIGIT 2ND DIGIT Solder
COMMON Soldering
CATHODE iron
MULTIPLIER
=1600 = 1.6k 6. Check with a magnifier for solder bridge between
the pins or for dry joint between pins and soldering
ANODES SOLDER pads. To remove a solder bridge, use a de-solder
CAPS
RESISTOR
braid as shown in the figure below.
MH DIODE
De-Solder
braid
Solder Soldering
bridge iron
-4-
Service notes (continued)
IMPORTANT: To protect against possible damage to Procedure:
the solid state devices due to arcing or static discharge, 1. Connect receiver to isolator transformer.
make certain that all ground wires and CTR DAG wire 2. Apply a monoscope pattern.
are securely connected. 3. In service mode. (Refer to service mode section)
CAUTION: The power supply circuit is above earth select register C0b.
ground and the chassis cannot be polarized. Use an 4. Measure TP5 (TPs port close to tuner). Compare
isolation transformer when servicing the receiver to the measure of TP5 and set the data for C0b
avoid damage to the test equipment or to the chassis. according the following table
Connect the test equipment to the proper ground ( ) or
( ) when servicing, or incorrect voltages will be TP5 DATA TO
measured. MEASURE (V) C0b (Hex)
-5-
Receiver feature table
FEATURE\MODEL CT-20G7DF CT-20D12DF
*Note: When ordering a board, add and ” S” after the board suffix application.
Example, If order A-Board for CT-20G7DF, should be ordered as: TNP2AH040DHS.
-6-
Chasis service adjustment procedures
All service adjustments are factory preset and should not require adjustment unless controls and/or
associated components are replaced.
Note: Connect the (-) lead of the voltmeter to the appropriate ground. Use IC801’s heat sink when the HOT
ground symbol ( ) is used. Otherwise, use COLD ground ( ) — tuner shield, IC451’s heat sink or FA2.
IC003
IC002
IC552 TPD15
IC001 IC050
IC551 TPD16
IC801
T CRT
U TPE10 HOT ( )
GND
N TPE11
IC2302 D561
E COLD ( )
R
IC2301
F801
TPD8
D554
TPD9
FA1 CLK
DATA FA2 FOCUS SCREEN
COMPONENTS WITHIN DOT LINES ARE LOCATED AT THE OPOSITE SIDE OF BOARD.
130.0V B+ voltage confirmation LOCATION VOLTAGE
1. Set the BRIGHT and the PICTURE to minimum by
using the PICTURE menu. IC552 Pin3 5.0V ± 0.25V
2. Connect the DVM between C825 (+ side) and cold
IC551 Pin3 9.0V ± 0.25V
ground ( ).
3. Confirm that B+ voltage is 130.0V ± 2.5V. This D554 Cathode 200V ± 15V
voltage supplies B+ to the horizontal output &
flyback circuits. Adjust PICTURE menu for normalized video
Source voltage chart adjustments.
120V AC line input. Set the BRIGHT and the PICTURE
to minimum by using the PICTURE menu. Use cold High voltage check
ground ( ) for the (-) lead of the DVM. 1. Select an active TV channel and confirm that the
horizontal is in sync.
LOCATION VOLTAGE 2. Adjust BRIGHTNESS and PICTURE using picture
icon menu, so video just disappears.
TPD8 26.0V ± 2V 3. Confirm B+ 130V is within limit.
TPD9 25.0V ± 2V 4. Using a high voltage meter confirm that the high
voltage is:
26.60kV±1.25kV
-7-
MAIN TUNER
TNR001
A-BOARD
LEFT&RIGHT
CHANNELS
LEFT CHANNEL
14 AUDIO AMP LEFT +
LEFT
10 LEFT
OUT
-
MPX IN LEFT 21 LEFT 3 TV IN OUT SPEAKER
OUT
6 VOL VAO 5
IC2201 SP SW
9
MTS
-8-
ANN5829S-E1V.
RIGHT RIGHT
22 3 TV IN
OUT
- RIGHT
LEFT RIGHT RIGHT RIGHT SPEAKER
6 VOL 10 +
IN IN OUT OUT
2 3
9 SP SW VAO 5
VOL SP / CP
LEFT LEFT
Audio signal path block diagram
IC001
RIGHT RIGHT MPU/VCJ
M65580MAP10 AUDIO
OUT
A/V 1 A/V 2
Q055
26 28 A11 C1 C-BOARD
TV IN FB
28 R-OUT Q006 1 1
22 Y IN
IC001 Q354 -R Q351 -R
24 C IN MPU/VCJ 30 G-OUT Q007 2 2 Q355 -G Q352 -G
M65580MAP10 Q356 -B Q353 -B
-9-
72 SSW
32 B-OUT Q008 3 3
JK3001 HALF-
OSD
EXT B G R TONE
1 4 8
20 48 49 51 59
5
IC050
6
HALFTONE
13
V IDEO IN
Video signal path block diagram
A/V 1 A/V 2
REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION
- 11 - Parts List
120-02
REPLACEMENT PARTS LIST
Models: CT-20D12DF, CT-20G7DF
Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing
any of these components use only manufacturer’s specified parts.
REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION
D3019 MA3110MTX DIODE, ZENER L416 EXCELSA39V FERRITE BEAD
D3020 MA3110MTX DIODE, ZENER L551 ELH5L4101 COIL
D3021 MA3110MTX DIODE, ZENER L801 ELF15N011A COIL, PEAKING
D3022 MA3110MTX DIODE, ZENER L802 ELEIE680KA COIL, PEAKING 68UH
FUSES L803 TALL08T680KA COIL
F801 XBA2A00101 FUSE 6.3A 125V L2305 EXCELSA35V FERRITE BEAD
INTEGRATED CIRCUITS L2308 EXCELSA24V FERRITE BEAD
IC001 M65580MAP103 MPU/VCJ L2350 ELESN4R7JA COIL, PEAKING 4.7UH
IC002 TVR2AJ125 EEPROM TRANSISTORS
IC003 PIC-37042SR IR RECEIVER Q001 2SD601ARTX TRANSISTOR
IC005 PQ1X331M2ZP VOLTAGE REGULATOR, 3.3V Q006 2SB709ARTX TRANSISTOR
IC006 MN1280R RESET Q007 2SB709ARTX TRANSISTOR
IC050 TC74HC4066AL HALFTONE Q008 2SB709ARTX TRANSISTOR
IC451 LA7837-TV V-OUT Q009 2SC1473A TRANSISTOR
IC551 AN78L09 INT CKT CT-20D12DF Q050 2SB709ARTX TRANSISTOR
IC551 AN78M09LB VOLTAGE REGULATOR 9V CT-20G7DF Q051 2SB709ARTX TRANSISTOR
IC552 AN78M05LB VOLTAGE REGULATOR, 5V Q052 2SB709ARTX TRANSISTOR
IC553 AN78M05LB VOLTAGE REGULATOR, 5V Q053 2SD601ARTX TRANSISTOR
IC801 STRG5623A POWER SUPPLY, 360V Q054 2SD601ARTX TRANSISTOR
IC2201 AN5829S-E1V MTS, S-AGC Q055 2SD601ARTX TRANSISTOR
IC2301 AN17800A AUDIO AMP CT-20G7DF Q090 2SB709ARTX TRANSISTOR
IC2301 AN17801A AUDIO AMP CT-20D12DF Q092 2SB709ARTX TRANSISTOR
IC2302 AN17800A AUDIO AMP CT-20G7DF Q351 2SC3063RL TRANSISTOR
IC2302 AN17801A AUDIO AMP CT-20D12DF Q352 2SC3063RL TRANSISTOR
COILS Q353 2SC3063RL TRANSISTOR
L001 EXCELSA35T FERRITE BEAD Q354 2SD601ARTX TRANSISTOR
L003 TLUABTA2R2K COIL, PEAKING 2.2UH Q355 2SD601ARTX TRANSISTOR
L004 TLUABTA2R2K COIL, PEAKING 2.2UH Q356 2SD601ARTX TRANSISTOR
L005 EXCELDR35V FERRITE BEAD Q451 2SD601ARTX TRANSISTOR
L006 EXCELSA24T FERRITE BEAD Q452 2SD601ARTX TRANSISTOR
L007 EXCELDR35V FERRITE BEAD Q453 2SD601ARTX TRANSISTOR
L008 TLUABTA470K COIL, PEAKING 47UH Q501 2SC1573AH TRANSISTOR
L009 EXCELSA35V FERRITE BEAD Q505 2SD601ARTX TRANSISTOR
L010 ELESN330JA COIL, PEAKING 33UH Q520 2SD601ARTX TRANSISTOR
L011 ELESN330JA COIL, PEAKING 33UH Q551 2SC562200VLA TRANSISTOR
L013 EXCELDR35V FERRITE BEAD Q605 2SB709ARTX TRANSISTOR
L014 ELESN180KA COIL, PEAKING 18UH Q606 2SD601ARTX TRANSISTOR
L015 EXCELSA35V FERRITE BEAD Q820 2SA1767QTA TRANSISTOR
L016 EXCELSA35V FERRITE BEAD Q830 2SB1011QRL TRANSISTOR
L017 TLUABTA100K COIL, PEAKING 10UH Q2350 2SB709ARTX TRANSISTOR
L018 TLUABTA150K COIL, PEAKING 15UH RELAYS
L019 EXCELDR35V FERRITE BEAD RL801 TSEH0005 RELAY
L090 EXCELSA24T FERRITE BEAD RESISTORS
PARTS LIST
- 13 - Parts List
120-02
REPLACEMENT PARTS LIST
Models: CT-20D12DF, CT-20G7DF
Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing
any of these components use only manufacturer’s specified parts.
REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION
R506 ERJ6GEYJ333V RES,M 33K-J-1/10W R2307 ERJ6GEYJ103V RES,M 10K-J-1/10W
R507 ERJ6GEYJ103V RES,M 10K-J-1/10W R2320 ERJ6GEYJ104V RES,M 100K-J-1/10W CT-20D12DF
R508 ERJ6GEYJ103V RES,M 10K-J-1/10W R2350 ERDS2TJ391T RES,C 390-J-1/4W
R510 ERG3FJ272 RES,M 2.7K-J-3W R2351 ERJ6GEYJ562V RES,M 5.6K-J-1/10W
R512 ERG2FJ562H RES,M 5.6K-J-2W R2352 ERJ6GEYJ683V RES,M 68K-J-1/10W
R520 ERJ6GEYJ471V RES,M 470-J-1/10W R2353 ERJ6GEYJ124V RES,M 120K-J-1/10W
R521 ERJ6GEYJ272V RES,M 2.7K-J-1/10W R2354 ERJ6GEYJ123V RES,M 12K-J-1/10W
R531 ERD25FJ470P RES,C 47-J-1/4W R2355 ERJ6GEYJ222V RES,M 2.2K-J-1/10W
R532 ERJ6ENF8871V RES,M 8.87K-F-1/10W R2356 ERJ6GEYJ101V RES,M 100-J-1/10W
R533 ERJ6ENF1301V RES,M 1.3K-F-1/10W R2357 ERJ6GEYJ472V RES,M 4.7K-J-1/10W
R551 ERDS1FJ1R0T RES,C 1.0-J-1/2W R2365 ERDS2TJ102T RES,C 1K-J-1/4W
R552 ERDS1FJ1R0T RES,C 1.0-J-1/2W R2370 ERJ6GEYJ103V RES,M 10K-J-1/10W
R555 ERDS1FJ101T RES,C 100-J-1/2W R2417 ERJ6GEYJ104V RES,M 100K-J-1/10W CT-20D12DF
R556 ERG1SJ221P RES,M 220-J-1W R3001 ERDS2TJ101T RES,C 100-J-1/4W
R557 ERJ6GEYJ103V RES,M 10K-J-1/10W R3005 ERJ6GEYJ334V RES,M 330K-J-1/10W
R558 ERQ2CJP2R2S RES,F 2.2-J-2W R3007 ERJ6GEYJ151V RES,M 150-J-1/10W
R559 ERG2FJ683H RES,M 12K-J-2W R3008 ERJ6GEYJ151V RES,M 150-J-1/10W
R562 ERG3FJ680H RES,M 68-J-3W R3009 ERJ6GEYJ682V RES,M 6.8K-J-1/10W
R563 ERG1SJ150P RES,M 15-J-1W R3010 ERJ6GEYJ334V RES,M 330K-J-1/10W
R567 ERG2FJ122H RES,M 12K-J-2W R3011 ERJ6GEYJ682V RES,M 6.8K-J-1/10W
R572 ERJ6GEYJ222V RES,M 2.2K-J-1/10W R3013 ERJ6ENF75R0V RES,M 75.0-F-1/10W CT-20D12DF
R605 ERDS2TJ103T RES,C 10K-J-1/4W R3014 ERJ6ENF75R0V RES,M 75.0-F-1/10W CT-20D12DF
R606 ERJ6GEYJ562V RES,M 5.6K-J-1/10W R3016 ERDS2TJ181T RES,C 180-J-1/4W
R607 ERJ6GEYJ102V RES,M 1K-J-1/10W R3017 ERDS2TJ181T RES,C 180-J-1/4W
R608 ERJ6GEYJ104V RES,M 100K-J-1/10W R3018 ERJ6GEYJ682V RES,M 6.8K-J-1/10W
R801 ERF7ZK1R5 RES,W 1.5-K-7W R3019 ERJ6GEYJ682V RES,M 6.8K-J-1/10W
R802 ERDS2TJ684T RES,C 680K-J-1/4W R3050 ERJ6GEYJ101V RES,M 100-J-1/10W CT-20D12DF
R803 ERG2FJ100H RES,M 10K-J-1/2W R3051 ERJ6GEYJ101V RES,M 100-J-1/10W CT-20D12DF
R804 ERG2FJ104H RES,M 100K-J-2W SWITCHES
R805 ERX2FZJR18H RES,M .18-J-2W S001 EVQPF106K SWITCH
R806 ERX2FJR56H RES,M .56-J-2W S002 EVQPF106K SWITCH
R807 ERDS2TJ681T RES,C 680-J-1/4W S003 EVQPF106K SWITCH
R808 ERDS2TJ4R7T RES,C 4.7-J-1/4W S004 EVQPF106K SWITCH
R809 ERDS2TJ472T RES,C 4.7K-J-1/4 S005 EVQPF106K SWITCH
R815 ERC12ZGM825D RES,S 8.2MEG-M-1/2 S008 EVQPF106K SWITCH
R817 ERX3FJ6R8 RES,M 6.8-J-3W S009 EVQPF106K SWITCH
R821 ERDS1FJ1R5T RES,C 1.5-J-1/2W TRANSFORMERS
R822 ERDS1FJ1R5T RES,C 1.5-J-1/2W T501 TLH15452 TRANSFORMER HORIZONTAL DRIVER
R823 ERDS1FJ272T RES,C 2.7K-J-1/2W T551 KFT3AA341F TRANSFORMER FLYBACK
R824 ERDS2TJ223T RES,C 22K-J-1/4W T801 ETS29AS183NC TRANSFORMER
R825 ERDS2TJ272T RES,C 2.7K-J-1/4W CRYSTALS/FILTERS
R828 ERJ6GEYJ104V RES,M 100K-J-1/10W X001 TSSA092 CRYSTAL OSCILLATOR
R830 ERDS2TJ104T RES,C 100K-J-1/4W X002 AF080005BE CRYSTAL OSCILLATOR
PARTS LIST
RESISTOR CAPACITOR
TYPE TOLERANCE TYPE TOLERANCE
C Carbon F ± 1% C Ceramic C ± 0.25pF
F Fuse J ± 5% E Electrolytic D ± 0.5pF
M Metal Oxide K ± 10% P Polyester F ± 1pF
S Solid M ± 20% S Styrol J ± 5%
W Wire Wound G ± 2% T Tantalum K ± 10%
L ± 15%
RES, C 270-J-1/4
M ± 20%
P +10% -0%
Z +80% -20%
CAP, P .068UF-K-50V
PARTS LIST
- 15 - Parts List
120-02
Notes:
IMPORTANT SAFETY NOTICE
CHIP TRANSISTOR
THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL
LEAD DESIGNATION
FEATURES THAT ARE IMPORTANT FOR PROTECTION FROM
X-RADIATION, FIRE AND ELECTRICAL SHOCK HAZARDS.
WHEN SERVICING IT IS ESSENTIAL THAT ONLY
B
C
MANUFACTURERS SPECIFIED PARTS BE USED FOR THE E
CRITICAL COMPONENTS DESIGNATED WITH A IN THE
SCHEMATIC.
SCHEMATIC NOTES
1. Resistors are carbon 1/4W unless noted 6. (BOLD LINE) indicates the route
otherwise. of B+ supply.
2. Capacitors are ceramic 50V unless noted 7. The schematic diagrams are current at
otherwise. the time of printing and are subject to
3. Coil value notes is inductance in µH. change without notice.
4. Test point indicated by ; Test point but no 8. Ground symbol indicates HOT
pin . GROUND CONNECTION;
5. Components indicated with are critical indicates COLD GROUND.
parts and replacement should be made NOTE: All other component symbols are
with manufacture specified replacement used for engineering design
parts only. purposes.
VOLTAGE MEASUREMENTS
1. Voltage measurement: - Voltage readings are nominal and
- AC input to the Receiver is 120V. may vary ±10% on active devices.
NTSC (HD, 1125i & 525P when Some voltage reading will vary
applicable) signal generator is with signal strength and picture
connected to the antenna of the content.
Receiver. (Color bar pattern of 100 - Supply voltages are nominal.
IRE white and 7.5 IRE black.) 2. Ground symbol indicates ground lead
- All Picture and Audio adjustments are connection of meter.
set to Normalize. Incorrect ground connection will result
TV ANT/CABLE - (Set-Up Menu) in in erroneous readings.
TV/ANT Mode CAUTION: Incorrect ground connection
Volume - Min. of the test equipment will result in
TV/Video SW - TV position erroneous readings.
Audio Mode - Stereo
3 WAVEFORM MEASUREMENTS
1. indicates waveform measurement. 4. All video and color waveforms are taken
(Measurement can be taken at the best with a wideband scope and a probe
accessible location in common to the with low capacitance (10 to 1). Shape
indicated point.) and peak altitudes may vary
2. Taken with an NTSC signal generator depending on the type of Oscilloscope
connected to the antenna terminal. used and its settings.
(NTSC color bar pattern of 8 bars of EIA 5. Ground symbol shown on waveform
colors, 100 IRE white and 7.5 IRE black.) number indicates (Hot) ground lead
3. Customer Controls (Picture/Audio Menu) are connection of the Oscilloscope.
set to Normalize. Volume is set to “MIN”. CAUTION: Incorrect ground connection of
the test equipment will result in erroneous
readings.
PARTS LIST
- 16 -
Notas
NOTA DE SEGURIDAD
LOS DIAGRAMAS ELÉCTRICOS INCLUYEN
CARACTERÍSTICAS ESPECIALES MUY IMPORTANTES IDENTIFICACIÓN DE TERMINALES
PARA LA PROTECCIÓN CONTRA RAYOS-X, PARA TRANSISTORES EN CHIP
QUEMADURAS Y DESCARGAS ELÉCTRICAS. CUANDO
SE DE SERVICIO ES IMPORTANTE USAR PARA B
REEMPLAZO DE COMPONENTES CRITICOS, SOLO C
E
PARTES ESPECIFICADAS POR EL FABRICANTES. LOS
COMPONENTES CRITICOS ESTAN SEÑALADOS EN LOS
DIAGRAMAS POR EL SIMBOLO .
MEDICIÓN DE VOLTAJES
1. Medición de voltaje: - Las mediciones de los voltajes son
- El voltaje de entrada al Receptor es de nominales y pueden variar hasta
120V de Corriente Alterna. Un 10% en componentes en
generador de patrones con formato funcionamiento. Las lecturas de los
NTSC se conecta a la entrada de la voltajes pueden variar por la
antena. (Patrón de Barras de Colores potencia de la señal y el contenido
con 100 IREs para el Blanco y 7.5 IREs de la imagen.
para el Negro.) - Las fuentes de voltajes son
- Los ajustes de los Menus Picture y nominales.
Audio se normalizan. 2. El símbolo indica el tipo de tierra que
En el Menú Set-Up, en la opción se utiliza en la conexión del medidor.
ANTENA, se selecciona el modo de
CABLE. PRECAUCION: SI no se utiliza la
El nivel de Volumen se minimiza. conexión a la tierra adecuada, se
De los modos TV y Video, seleccionar el obtendrán mediciones equivocadas y
modo TV. podría dañar el equipo de medición.
Seleccionar modo Estereo del Audio.
EAI, formato NTSC de 100 IREs para el se utiliza conexión a Tierra Caliente en
Blanco y 7.5 IREs para el Negro.) el extremo negativo de la punta de
3. Los ajustes de usuario de los Menus prueba.
PICTURE y AUDIO se normalizaron.
PRECAUCION: Si no se utiliza la conexión
Posteriormente el nivel de volumen se
a la tierra adecuada, se obtendrán
ajusta al mínimo.
mediciones equivocadas y podría dañar el
4. Las formas de onda de Video y Color
equipo de medición.
fueron tomadas con un osciloscopio de
- 17 -
A&C-Board Layout - 18 -
- 19 - A&C-Board Layout
A-Board CT-20G7DF - 20 -
- 21 - A-Board CT-20G7DF
A-Board CT-20G7DF - 22 -
- 23 - A-Board CT-20G7DF
A-Board CT-20G7DF - 24 -
NOTES:
- 25 - Notes
A-Board CT-20D12DF - 24 -
- 25 - A-Board CT-20D12DF
A-Board CT-20D12DF - 26 -
- 27 - A-Board CT-20D12DF
A-Board CT-20D12DF - 28 -
C-Board schematic
1 1.3V p-p [20µs] 1.40V p-p [20µs] 28V p-p [5ms] 112V p-p [5ms]
5 9 13
TPA5 (VIDEO) (B OUT) IC451-13 (PUMP-UP) Q551-Collector H Out
A11-3
14.20MHz Xtal
IC001 PIN 35 9.20V p-p [20µs] 5.52V p-p [5ms] 276V p-p [20µs]
2 6 10 14
A/D C OSC V IN IC001-44 (H PULSE) IC801-1
IC451-2
3 1.68V p-p [20µs] 1.32V p-p [20µs] 3.12V p-p [5ms] 2.90V p-p [20µs]
7 11 15
A11-1 (R OUT) V DRIVE IC801-5
IC001-43 (FBT PULSE)
IC451-7
- 31 - A-Board IC voltages
®
Printed in USA
K02052597PL0516