Professional Documents
Culture Documents
950g Wheel Loader 2js00001-Up (Machine) Powered by 3126 Engine (Sebp2529 - 83)
950g Wheel Loader 2js00001-Up (Machine) Powered by 3126 Engine (Sebp2529 - 83)
Pantalla anterior
Bienvenido: r180ta
Producto: WHEEL LOADER
Modelo: 950G WHEEL LOADER 2JS
Configuración: 950G Wheel Loader 2JS00001-UP (MACHINE) POWERED BY
3126 Engine
Pruebas y Ajustes
950G Wheel Loader and 962G
Wheel Loader Electrohydraulic System
Número de medio -RENR2146-05 Fecha de publicación -01/02/2011 Fecha de actualización -08/02/2011
i01261772
Table 1
Required Tools
Part Number Description
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the attachments have been lowered, oil is cool before
removing any components or lines. Remove the oil filler cap only when
the engine is stopped, and the filler cap is cool enough to touch with
your bare hand.
Lower the bucket and/or attachments to the ground and engage the
parking brake.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Running Engine
Illustration 1 g00336022
Pilot Control Valve
(1) Pressure reducing valve. (2) Pressure reducing valve. (3) Pressure tap.
3. Start the engine and run the engine at high idle. Bring the oil to normal operating temperature. The
pressure reading should be 3450 ± 200 kPa (500 ± 29 psi).
5. If the pressure reading is not correct, stop the engine and release the hydraulic system pressure. Refer
to Testing and Adjusting, "System Pressure - Release".
6. For an electro-hydraulic system, replace 114-1266 Pressure Reducing Valve (2). For a pilot hydraulic
system, replace the 154-0191 Pressure Reducing Valve. Tighten the valve to a torque of 60 ± 7 N·m
(45 ± 5 lb ft).
8. Stop the engine and remove the test equipment from pressure tap (3) .
Illustration 2 g00336022
Pilot Control Valve
(1) Pressure reducing valve. (2) Pressure reducing valve. (3) Pressure tap.
3. Start the engine and raise the bucket off the ground.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 3/4
23/3/2019 950G Wheel Loader 2JS00001-UP (MACHINE) POWERED BY 3126 Engine(SEBP2529 - 83) - Documentación
4. Stop the engine. The oil must be at normal operating temperature. The pressure reading should be
2070 ± 200 kPa (300 ± 29 psi).
6. If the pressure reading is not correct, release the hydraulic system pressure. Refer to Testing and
Adjusting, "System Pressure - Release".
7. Replace the 114-1267 Secondary Pressure Reducing Valve (2). Tighten the valve to a torque of 60 ± 7
N·m (45 ± 5 lb ft).
Copyright 1993 - 2019 Caterpillar Inc. Sat Mar 23 2019 15:55:30 GMT-0400 (hora de Bolivia)
Todos los derechos reservados.
r180ta
Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 4/4